TI TPS79718-EP

TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
ULTRA LOW-POWER, 10 mA, LDO LINEAR REGULATORS WITH POWER GOOD OUTPUT
FEATURES
APPLICATIONS
•
•
1
•
•
•
•
•
•
•
•
•
•
•
(1)
Controlled Baseline
– One Assembly Site
– One Test Site
– One Fabrication Site
Extended Temperature Performance of
–55°C to 125°C
Enhanced Diminishing Manufacturing Sources
(DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree(1)
10 mA Low-Dropout Regulator
Ultralow 1.2 µA Quiescent Current at 10 mA
5-Pin SC70/SOT-323 (DCK) Package
Integrated Power Good Output
Stable With Any Capacitor (> 0.47 µF)
Dropout Voltage Typically 105 mV at 10 mA
(TPS79733)
Overcurrent Limitation
Component qualification in accordance with JEDEC and
industry standards to ensure reliable operation over an
extended temperature range. This includes, but is not limited
to, Highly Accelerated Stress Test (HAST) or biased 85/85,
temperature cycle, autoclave or unbiased HAST,
electromigration, bond intermetallic life, and mold compound
life. Such qualification testing should not be viewed as
justifying use of this component beyond specified
performance and environmental limits.
Battery-Powered Microcontrollers and
Microprocessors
DESCRIPTION/ORDERING INFORMATION
The TPS797xx family of low-dropout (LDO) voltage
regulators offers the benefits of low-dropout voltage
and ultralow-power operation. The device is stable
with any capacitor (> 0.47 µF). Therefore,
implementations of this device require little board
space due to the miniaturized packaging and
potentially small output capacitor. In addition, the
family includes an integrated open drain active-high
power good (PG) output. Intended for use in
microcontroller based, battery-powered applications,
the
TPS797xx
family's
low
dropout
and
ultralow-powered operation results in a significant
increase in system battery operating life. The small
packaging minimizes consumption of board space.
The device is enabled when the applied voltage
exceeds the minimum input voltage. The usual PNP
pass transistor has been replaced by a PMOS pass
element. Because the PMOS pass element behaves
as a low-value resistor, the dropout voltage is low,
125 mV (typ) at 10 mA of load current and is directly
proportional to the load current. The quiescent current
is ultralow (1.2 µA typ) and is stable over the entire
range of output load current (0 mA to 10 mA). When
properly configured with a pullup resistor, the PG
output can be used to implement a power-on reset or
low battery indicator. The TPS797xx is offered in
1.8 V, 3 V, and 3.3 V fixed options.
ORDERING INFORMATION (1)
TA
PACKAGE (2)
VOLTAGE
1.8 V
–55°C to 125°C
3V
SC70/SOT-323 (DCK)
3.3 V
(1)
(2)
(3)
PART NUMBER
SYMBOL
TPS79718MDCKREP
CKW
TPS79730MDCKREP
BUA
TPS79733MDCKREP (3)
TBD
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
Product Preview. Parameters in electrical characteristics are subject to change.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2007, Texas Instruments Incorporated
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
DCK PACKAGE
(TOP VIEW)
1
GND
2
NC
3
5
OUT
2
VI = 4.3 V
VO = 3.3 V
Co = 1 µF
IO = 10 mA
1.75
4
Ground Current − µ A
PG
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
IN
1.50
1.25
1
0.75
0.50
−40
−15
10
35
60
TA − Free-Air Temperature − °C
85
DEVICE INFORMATION
FUNCTIONAL BLOCK DIAGRAM
VOUT
VIN
Current
Sense
ILIM
_
R1
+
GND
R2
Vref = 1.235 V
Bandgap
Reference
VIN
PG
Delay
TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
IN
4
GND
2
NC
3
OUT
5
PG
2
1
I/O
I
DESCRIPTION
The IN terminal is the power supply input to the device.
Ground
No connection
O
The OUT terminal provides the regulated output voltage of the device.
O
The PG terminal for the fixed voltage option devices is an open-drain active-high output that indicates
the status of VO (output of the LDO). When VO exceeds approximately 90% of the regulated voltage,
PG goes to a high impedance state. It goes to a low-impedance state when VO falls below
approximately 90% (i.e. overload condition) of the regulated voltage. The open drain output of the PG
terminal requires a pullup resistor.
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
Input voltage range (2)
Maximum dc output voltage
Peak output current
VALUE
UNIT
0.3 to 6
V
4.9
V
Internally limited
ESD rating, HBM
3
kV
ESD rating, CDM
1
kV
Continuous total power dissipation
See Dissipation Rating Table
TJ
Operating junction temperature range
–55 to 145
°C
TA
Operating ambient temperature range
–55 to 125
°C
Tstg
Storage temperature range
–65 to 150
°C
(1)
(2)
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
DISSIPATION RATINGS
BOARD
PACKAGE
RθJC
(°C/W)
RθJA
(°C/W)
DERATING
FACTOR
ABOVE
TA = 25°C
TA ≥ 25°C
POWER
RATING
TA = 70°C
POWER
RATING
TA = 85°C
POWER
RATING
Low K
DCK
165.39
396.24
2.52 mW/°C
252 mW
139 mW
101 mW
0W
High K
DCK
165.39
314.74
3.18 mW/°C
318 mW
175 mW
127 mW
127 mW
Copyright © 2006–2007, Texas Instruments Incorporated
TA = 125°C
POWER
RATING
Submit Documentation Feedback
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
3
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
ELECTRICAL CHARACTERISTICS
over operating free-air temperature range (unless otherwise noted)
PARAMETER
VI
TEST CONDITIONS
MIN
IO = 3 mA
Input voltage (1)
Continuous output current
Operating ambient temperature
V
5.5
V
0
10
mA
–55
125
°C
1.895
V
3.12
V
3.432
V
TA = 25°C, 2.8 V < VI < 5.5 V
TPS79718
1.8
TJ = –55°C to 125°C,
2.8 V < VI < 5.5 V
1.705
TA = 25°C, 4 V < VI < 5.5 V
Output voltage
(1mA to 10mA load) (3)
TPS79730
3
TJ = –55°C to 125°C,
4 V < VI < 5.5 V
2.88
TA = 25°C, 4.3 V < VI < 5.5 V
TPS79733
Quiescent current (GND current) (3)
Load regulation
4
1.2
TJ = –55°C to 125°C, IO = 10 mA
5
17
VO + 1 V < VI ≤ 5.5 V, TA = 25°C
VO = 0 V, See Note 4
190
Power supply ripple rejection (TPS79718)
f = 100 Hz, CO = 10 mF, IO = 10 mA,
TA = 25°C
105
IO = 10 mA, TA = –55°C to 125°C
VO decreasing
VI = 1.4 V, I(PG) = 100 uA
PG leakage current
V(PG) = 5 V
mA
dB
400
IO = 10 mA, TA = 25°C
PG output low voltage
300
125
IO = 10 mA, TA = –55°C to 125°C
PG trip threshold voltage
%/V
µVRMS
50
IO = 10 mA, TA = 25°C
I(PG) = 100 uA, V(PG) ≥ 0.8 V
mV
0.8
Output current limit
Minimum input voltage for valid PG
µA
0.15
VO + 1 V < VI ≤ 5.5 V,
TJ = –55°C to 125°C
600
TPS79733
(4)
TA = 25°C, 0 mA < IO < 10 mA
BW = 200 Hz to 100 kHz,
CO = 10 mF,
IO = 10 mA, TA = 25°C
Dropout voltage (4)
(3)
3.168
Output noise voltage (TPS79718)
TPS79730
(1)
(2)
3.3
TJ = –55°C to 125°C,
4.3 V < VI < 5.5 V
TA = 25°C, IO = 1 mA to 10 mA
Output voltage line regulation
(ΔVout/ΔVin) (3)
UNIT
2
(2)
TA
MAX
5.5
IO = 10 mA
IO
TYP
1.8
mV
400
1.2
V
90
0.14
0.1
%VO
0.4
V
nA
To calculate the minimum input voltage for your maximum output current, use the following formula: VI(min) = VO(max) + VDO (max load)
Continuous output current is limited by internal protection circuitry, but it is not recommended that the device operate under conditions
beyond those specified in this table for extended periods of time.
The minimum IN operating voltage is 1.8 V or VO (typ) + 1 V, whichever is greater. The maximum IN voltage is 5.5 V. There is no
minimum output current requirement and the maximum output current is 10 mA.
IN voltage equals VO(typ) – 100 mV; The TPS79730 input voltage is set to 2.9 V and the TPS79733 input voltage is set to 3.2 V. The
TPS79718 dropout voltage is limited by input voltage range limitations.
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
TPS797xx PG TIMING DIAGRAM
VIN
Vmin
(see Note A)
t
VOUT
Threshold
Voltage
VIT +
(see Note B)
VIT −
(see Note B)
t
PG
Output
t
A.
Vmin = VOUT + VDO
B.
The PG trip voltage is typically 10% lower than the output voltage (90%VO). VIT- to VIT+ is the hysteresis voltage.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
5
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.315
1.815
VI = 4.3 V
Co = 1 µF
TA = 25°C
3.35
VI = 2.8 V
Co = 1 µF
TA = 25°C
3.305
3.300
3.295
3.33
1.805
1.800
1.795
3.290
1.790
3.285
1.785
VI = 4.3 V
Co = 1 µF
3.34
V O − Output Voltage − V
1.810
V O − Output Voltage − V
3.310
V O − Output Voltage − V
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
3.32
3.31
IO = 1 mA
3.30
3.29
IO = 10 mA
3.28
3.27
3.26
0
2
4
6
8
IO − Output Current − mA
2
4
6
8
IO − Output Current − mA
10
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
Ground Current − µ A
IO = 1 mA
IO = 10 mA
1.79
VI = 4.3 V
VO = 3.3 V
Co = 1 µF
IO = 10 mA
1.50
1.25
1
0.75
−15
10
35
60
TA − Free-Air Temperature − °C
0.50
−40
85
IO = 10 mA
6
IO = 1 mA
4
2
0
−15
10
35
60
TA − Free-Air Temperature − °C
85
100
1k
10 k
f − Frequency − Hz
Figure 6.
OUTPUT IMPEDANCE
vs
FREQUENCY
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
vs
POWER UP / POWER DOWN
IO = 1 mA
25
20
IO = 10 mA
15
10
VI = 3.2 V
Co = 1 µF
100
IO = 10 mA
80
60
40
IO = 1 mA
20
5
0
100
1k
10k
100k
1M
10 M
f − Frequency − Hz
0
−40 −25
−10
VO = 3.3 V
RL = 330 Ω
6
VO − Output Voltage − V
V − Input Voltage − V
I
120
5
20
35
5
VI
4
3
VO
2
1
0
50
65
80
0
TA − Free-Air Temperature − °C
Figure 7.
10 20
30 40 50
60 70 80 90 100
t − Time − ms
Figure 8.
Submit Documentation Feedback
100 k
7
140
V DO − Dropout Voltage − mV
Zo − Output Impedance − Ω
8
Figure 5.
VI = 4.3 V
VO = 3.3 V
Co = 1 µF
TJ = 25°C
10
VI = 2.8 V
VO = 1.8 V
Co = 1 µF
Figure 4.
40
6
10
Output Spectral Noise Density − nV/
1.75
Hz
2
1.80
30
85
Figure 3.
1.81
35
−15
10
35
60
TA − Free-Air Temperature − °C
Figure 2.
VI = 2.8 V
Co = 1 µF
1.78
−40
−40
Figure 1.
1.82
V O − Output Voltage − V
3.25
0
10
Figure 9.
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS (continued)
100
50
IO = 10 mA
VO = 1.8 V
Co = 4.7 µF
0
50
100
50
0
−50
VI = 2.8 V
VO = 1.8 V
Co = 4.7 µF
−100
10
5
1 mA
0
IO = 10 mA
Co = 4.7 µF
5.3
4.3
dv
0.14 V
=
dt
µs
200
100
0
−100
0 200 400 600 800 1 k 12
−100
V − Input Voltage − V
I
2.8
TPS79733
LINE TRANSIENT RESPONSE
V − Output Voltage − mV
O
3.8
∆ VO− Change In
Output Voltage − mV
0.14 V
dv
=
µs
dt
TPS79718
LOAD TRANSIENT RESPONSE
Current Load − mA
VO − Output Voltage − mV V − Input Voltage − V
I
TPS79718
LINE TRANSIENT RESPONSE
0 100 200 300 400 500 600 700 800 900 1 k
14 16
18
2k
t − Time − µs
t − Time − µs
Figure 10.
−200
0 100 200 300 400 500 600 700 800 900 1 k
Figure 11.
t − Time − µs
Figure 12.
VI = 4.3 V
Co = 4.7 µF
100
50
I O − Output Current − mA
0
−50
−100
10
∆ V − Change In
O
Output Voltage − mV
TPS79733
LOAD TRANSIENT RESPONSE
5
1 mA
0
0
200 400 600 800 1 k 12 14
16 18
2k
t − Time − µs
Figure 13.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
7
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
APPLICATION INFORMATION
The TPS797xx family of low-dropout (LDO) regulators haS been optimized for use in micropower applications.
The devices feature extremely low dropout voltages and ultralow quiescent current (1.2 µA typ).
A typical application circuit is shown in Figure 14.
TPS797xx
4
IN
PG 1
100 kΩ
+
C1
0.1 µF
OUT
5
VO
3
−
NC
GND
+
0.47 µF
2
Figure 14. Typical Application Circuit
External Capacitor Requirements
Although not required, a 0.1 µF or larger input bypass capacitor, connected between IN and GND and located
close to the TPS797xx, is recommended, especially when a highly resistive power supply is powering the LDO in
addition to other devices.
Like all low-dropout regulators, the TPS797xx requires an output capacitor connected between OUT and GND to
stabilize the internal control loop. The minimum recommended capacitance is 0.47 µF. Any 0.47 µF capacitor is
suitable. Capacitor values larger than 0.47 µF are acceptable.
Power Dissipation and Junction Temperature
Specified regulator operation is assured to a junction temperature of 125°C; restrict the maximum junction
temperature to 125°C under normal operating conditions. This restriction limits the power dissipation the
regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or
equal to PD(max).
T max * T
A
P
+ J
D(max)
R
θJA
The maximum-power-dissipation limit is determined using the following equation:
Where:
TJmax is the maximum allowable junction temperature.
RθJA is the thermal resistance junction-to-ambient for the package (see the Power Dissipation Rating Table).
TA is the ambient temperature.
The regulator dissipation is calculated using:
PD = (VI - VO) × IO
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal
protection circuit.
8
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
TPS79718-EP, TPS79730-EP, TPS79733-EP
www.ti.com
SGLS348A – AUGUST 2006 – REVISED OCTOBER 2007
Regulator Protection
The TPS797xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be
appropriate.
The TPS797xx features internal current limiting. During normal operation, the TPS797xx limits output current to
approximately 190 mA. When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. Take care not to exceed the power dissipation ratings of the package.
Microcontroller Application
One application for which this device is particularly suited is providing a regulated input voltage and power good
(PG) supervisory signal to low-power devices such as mixed-signal microcontrollers. The quiescent or ground
current of the TPS797xx family is typically 1.2 µA even at full load; therefore, the reduction in battery life by
including the TPS797xx in the system is negligible. The primary benefits of using the TPS797xx to power low
power digital devices include:
• Regulated output voltage that protects the device from battery droop and noise on the line (e.g., switch
bounce)
• Smooth, monotonic power up
• PG signal for controlled device RESET
• Potential to use an existing 5-V power rail to power a 3.3 V or lower device
• Potential to provide separate digital and analog power and ground supplies for a system with only one power
source
Figure 15 shows an application in which the TPS79718 is used to power Texas Instruments MSP430 mixed
signal microcontroller.
VOUT
VIN
VCC
1.8 V
+
0.47 µF
TPS79718
−
MSP430
or Equivalent
0.1 µF
PG
GND
RESET
VSS
Figure 15. MSP430 Microcontroller Powered by the TPS79718 Regulator
Minimal board space is needed to accommodate the DCK (SC70/SOT-323) packaged TPS79718, the 0.1 µF
output capacitor, the 0.47 µF input capacitor, and the pullup resistor on the PG pin.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS79718-EP TPS79730-EP TPS79733-EP
9
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS79718MDCKREP
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS79730MDCKREP
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
V62/06673-01XE
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
V62/06673-02XE
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS79718-EP, TPS79730-EP, TPS79733-EP :
TPS79718, TPS79730, TPS79733
• Catalog:
• Automotive: TPS79718-Q1, TPS79730-Q1, TPS79733-Q1
NOTE: Qualified Version Definitions:
- TI's standard catalog product
• Catalog
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Jul-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS79718MDCKREP
SC70
DCK
5
3000
180.0
8.4
2.25
2.4
1.22
4.0
8.0
Q3
TPS79730MDCKREP
SC70
DCK
5
3000
180.0
8.4
2.25
2.4
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Jul-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS79718MDCKREP
SC70
DCK
5
3000
202.0
201.0
28.0
TPS79730MDCKREP
SC70
DCK
5
3000
202.0
201.0
28.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated