MPSIND ADC401

ADC400 SERIES
1W, Ultra-High Isolation SIP, Single & Dual Output DC/DC Converters
Selection Guide
Model
Number
Input
Voltage
VDC
Output
Voltage
VDC
Output
Current
Efficiency
mA
% Typ.
Load
Regulation
% Max.
ADC401
5
200
66
10
ADC402
12
80
66
8
15
65
66
8
±5
±100
66
10
ADC405
±12
±40
72
8
ADC406
±15
±35
73
8
ADC411
5
200
66
10
ADC412
12
80
66
8
15
65
66
8
±5
±100
66
10
ADC415
±12
±40
74
8
ADC416
±15
±35
75
8
ADC403
5
(4.5 - 5.5)
ADC404
The ADC400 series is an excellent
selection for a variety of applications
including distributed power
systems, mixed analog/digital
subsystems, portable test
equipments, local power networks
and battery backed systems.
Pin Connections
22.0 [0.87]
2.54 [0.100]
3.5 [0.14]
12.5 [0.49]
The series consists of 12 models
with input voltages of 5V and
12VDC which offers standard
output voltages of 5V, 12V,
15VDC in both single and dual
output configurations.
Mechanical Dimensions
3.5 [0.14]
MPS Industries ADC400 1W
DC/DC's are specially designed
to provide ultra-high levels of
isolation 6000VDC in a miniature
SIP package.
ADC414
21.0 [0.83]
Pin
Singles
Duals
1
+Vin
+Vin
2
-Vin
-Vin
5
-Vout
-Vout
6
No Pin
Common
7
+Vout
+Vout
Case Size –
22.0x7.5x12.5mm (0.87x0.30x0.49inch)
Case Material –
1
2
5
0.50 [0.020]
6
7.5 [0.30]
•
•
•
ADC413
0.5 [0.02]
•
Efficiency up to 75%
6000VDC Isolation
MTBF > 2,000,000 Hours
Low Cost
Input 5 and 12VDC
Output 5, 12, 15,
±5, ±12 and ±15VDC
Temperature Performance
-25°C to +70°C
UL 94V-0 Package Material
Internal SMD Construction
Industry Standard Pin-out
7
2.0 [0.08]
•
•
•
•
•
•
12
(10.8 - 13.2)
0.25 [0.010]
Key Features
Non-Conductive Black Plastic
Weight –
3.9g (0.14Oz)
Tolerance
Pin
Millimeters
Inches
X.X±0.25
X.XX±0.01
X.XX±0.13
X.XXX±0.005
±0.05
±0.002
2463 208th Street, Ste. 205
Tel: (310) 533-1455
http://www.mpsind.com
Torrance, CA 90501
Fax: (310) 533-1853
E-mail: [email protected]
ADC400 SERIES
1W, Ultra-High Isolation SIP, Single & Dual Output DC/DC Converters
Absolute Maximum Ratings
Parameter
General Characteristics
Min.
Max. Units
5VDC Input Models
-0.7
9
VDC
12VDC Input Models
-0.7
18
VDC
Lead Temperature
(1.5mm from case for 10sec.)
---
260
°C
Internal Power Dissipation
---
650
mW
Input Surge Voltage
(1000mS)
Isolation
Voltage
Isolation
Resistance
Isolation
Capacitance
MTBF
Environmental Characteristics
Min.
Ambient
-25
70
°C
Line Regulation
Case
-25
90
°C
Load Regulation
-40
125
°C
Ripple & Noise
--95
Free-Air Convection
%
Short Circuit
Cooling
Min.
Typ.
Max.
Units
60 Seconds
6000
---
---
VDC
500VDC
10
---
---
GΩ
100kHz, 1V
---
15
20
pF
50
80
100
kHz
2
---
---
MHrs
Min.
Typ.
Max.
Units
---
±1.2
±1.5
%
MIL-HDBK-217F
@25°C
Ground Benign
Output Characteristics
Conditions
Operating
Temperature
Operating
Temperature
Storage
Temperature
Humidity
Conditions
Switching
Frequency
Exceeding the unit absolute maximum ratings could cause damage.
These are not continuous operating ratings.
Parameter
Parameter
Max. Units
Parameter
Conditions
For Vin Change of
1%
Io = 20% to 100%
See Selection Guide
20MHz BW
---
100
150
%
mV P-P
0.5 Second Max.
Maximum Capacitive Load
Models by Output Voltage
(Each Output on Duals)
Derating Curve
400LFM
100LFM
Output Power (%)
200LFM
60
Natural
convection
40
20
0
¡ã
-25
50
Duals
Units
680
220
uF
Notes:
100
80
Singles
60
70
80
Ambient Temperature
90
100
110
1. Specifications typical at Ta=+25°C, resistive load, nominal input
voltage, rated output current unless otherwise noted.
2. These power converters require a minimum output load to maintain
specified regulation.
3. Operation under no-load conditions will not damage these modules;
however, they may not meet all specifications listed.
4. All DC/DC converters should be externally fused at the front end for
protection.
5. Other input and output voltage may be available, please contact
factory.
6. All specifications subject to change without notice.
7. For detailed data sheet, please visit our website.
]
2463 208th Street, Ste. 205
Tel: (310) 533-1455
http://www.mpsind.com
Torrance, CA 90501
Fax: (310) 533-1853
E-mail: [email protected]