MURATA-PS HPR117VC

HPR1XXVC
0.75 Watt Single Output DC/DC Converter
The HPR1XXVC Series uses advanced
circuit design and packaging technology to deliver superior reliability and
performance. A 170kHz push-pull
oscillator is used in the input stage. Beatfrequency oscillation problems are reduced when using the HPR1XXVC Series
with high frequency isolation amplifiers.
Reduced parts count and high
efficiency add to the reliability of the
HPR1XXVC Series. The high efficiency of
the HPR1XXVC Series means less internal
power dissipation, as low as 190mW.
With reduced heat dissipation the
HPR1XXVC Series can operate at
higher temperatures with no degradation.
In addition, the high efficiency of the
HPR1XXVC Series means the series is
able to offer greater than 10 W/inch3 of
output power density. Operation down
to no load will not impact the reliability
of the series, although a >1mA minimum
load is needed to realize published
specifications.
The HPR1XXVC Series provides the
user a low cost converter without sacrificing reliability. The use of surface mounted
devices and advanced manufacturing technologies make it possible to offer premium
performance and low cost.
SPECIFICATIONS All specifications are typical at TA = +25°C nominal input voltage unless otherwise specified.
PRODUCT SELECTION CHART
MODEL
NOMINAL
INPUT
VOLTAGE
(VDC)
RATED
OUTPUT
VOLTAGE
(VDC)
RATED
OUTPUT
CURRENT
(mA)
NO LOAD
(mA)
5
5
5
5
5
5
12
12
12
12
12
12
15
15
15
15
15
15
24
24
24
24
24
24
5
12
15
±5
±12
±15
5
12
15
±5
±12
±15
5
12
15
±5
±12
±15
5
12
15
±5
±12
±15
150
62
50
±75
±30
±25
150
62
50
±75
±30
±25
150
62
50
±75
±30
±25
150
62
50
±75
±30
±25
20
20
20
20
20
20
10
10
10
10
10
10
8
8
8
8
8
8
8
8
8
8
8
8
HPR100VC
HPR101VC
HPR102VC
HPR103VC
HPR104VC
HPR105VC
HPR106VC
HPR107VC
HPR108VC
HPR109VC
HPR110VC
HPR111VC
HPR112VC
HPR113VC
HPR114VC
HPR115VC
HPR116VC
HPR117VC
HPR118VC
HPR119VC
HPR120VC
HPR121VC
HPR122VC
HPR123VC
INPUT CURRENT
RATED LOAD
(mA)
REFLECTED
RIPPLE
CURRENT
(mAp-p)
EFFICIENCY
(%)
216
212
212
218
212
200
90
81
81
88
81
81
72
72
72
72
63
63
48
48
45
45
45
45
10
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
15
15
15
15
15
15
69
70
71
68
68
75
69
77
77
71
74
77
69
69
69
69
76
79
65
65
76
69
67
69
Note: Other input to output voltages may be available. Please contact factory.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
HPR1XXVC.B01 Page 1 of 4
HPR1XXVC
0.75 Watt Single Output DC/DC Converter
SPECIFICATIONS, ALL MODELS
Specifications are at TA = +25°C nominal input voltage unless otherwise specified.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL
OUTPUT
INPUT
Voltage Range
4.5
5
5.5
VDC
10.8
12
13.2
VDC
13.5
15
16.5
VDC
21.6
24
26.4
VDC
Voltage Rise Time See Typical Performance Curves & Application Notes: “Capacitive Loading Effects on Start-Up of DC/DC Converters”
OUTPUT
Rated Power
750
mW
Voltage Setpoint Accuracy
Rated Load, Nominal VIN
±5
%
Ripple & Noise
BW = DC to 10MHz
150
200
mVp-p
BW =10Hz to 2MHz
30
40
mVrms
Voltage (Over Input Voltage Range) 1mA to Rated Current, VOUT = 5V
4.75
7
VDC
1mA to Rated Current, VOUT = 12V
11.40
15
VDC
1mA to Rated Current, VOUT = 15V
14.25
18
VDC
Temperature Coefficent
.01
.05
%/ °C
REGULATION
Load Regulation (All other modes)
Rated Load to 1mA Load
3
%
GENERAL
ISOLATION
Rated Voltage
750
VDC
Test Voltage
60 Hz, 10 Seconds
750
Vrms
Resistance
10
GΩ
Capacitance
25
100
pF
Leakage Current
VISO= 240VAC, 60Hz
2
8.5
μArms
Switching Frequency
170
kHz
Frequency Change
Over Line and Load
24
%
Package Weight
3
g
MTTF per MIL-HDBK-217, Rev. F*
Circuit Stress Method
Ground Benign
TA = +25°C
7.9
MHr
Fixed Ground
TA = +35°C
1.9
MHr
Naval Sheltered
TA = +35°C
1.2
MHr
Airborne Uninhabited Fighter
TA = +35°C
300
kHr
Moisture Sensitivity Level (MSL)
IPC/JEDEC J-STD-20
2
TEMPERATURE
Specification
-25
+25
+85
°C
Operation
-40
+100
°C
Storage
-40
+110
°C
SOLDERING INFORMATION
The HPR1XXVC devices are intended for wave soldering or manual soldering.
They are not intended to be subject to surface mount processes under any circumstances.
The normal wave soldering process can be used with these devices where the device is subjected
to a maximum wave temperature of 260°C for a period of no more than 10 seconds. Within this
time and temperature range, the integrity of the device’s plastic body will not be compromised and
internal temperatures within the converter will not exceed 175°C. Care should be taken to control
manual soldering limits identical to that of wave soldering.
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
HPR1XXVC.B01 Page 2 of 4
HPR1XXVC
0.75 Watt Single Output DC/DC Converter
TYPICAL PERFORMANCE CURVES
Specifications are at TA = +25°C nominal input voltage and nominal load.
VOUT VS LOAD
(5Vout Models)
VOUT VS LOAD
(±5Vout Models)
5.7
5.4
5.5
5.2
VOUT VS LOAD
(12Vout Models)
12.5
5.3
12.3
Vout
Vout
Vout
12.4
5.0
12.2
12.1
5.1
4.8
4.9
4.6
12.0
0
80
40
120
160
11.9
0
20
Output Current (mA)
40
60
0
80
VOUT VS LOAD
(±12Vout Models)
80
VOUT VS LOAD
(±15Vout Models)
16.0
15.7
12.4
15.5
12.3
15.5
Vout
Vout
Vout
60
16.5
15.9
12.5
40
Output Current each load (mA)
VOUT VS LOAD
(15Vout Models)
12.6
15.0
12.2
15.3
14.5
12.1
15.1
14.0
12.0
14.9
0
10
20
30
13.5
0
40
20
40
60
80
Output Current each load (mA)
Output Current each load (mA)
EFFICIENCY VS LOAD
OSCILLATION FREQUENCY VS
TEMPERATURE
90
0.2
0
0.4
0.6
0.8
1.0
Output Power each load (Watts)
220
Frequency (KHz)
75
Efficiency (%)
20
Output Current each load (mA)
60
45
30
15
0
0
20
60
40
200
180
160
140
80
-30
100
0
% of Rated Load (%)
30
60
90
Temperature (°C)
SAFE OPERATING AREA
LOAD CAPACITANCE vs INPUT RISE TIME
(5 Vout models)
600
50
Total Load Capacitance (uF)
Total Load Capacitance (uF)
500
400
300
SAFE OPERATING AREA
200
40
30
SAFE OPERATING AREA
20
10
100
0
0
0
5
10
15
20
25
30
35
Rise Time of Input Voltage (mS)
40
45
5
10
15
20
25
30
35
40
45
50
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(12 Vout models)
NOTES:
1.) When operated within the SAFE OPERATING AREA as defined
by the above curves, the output voltage of HPR1XXC devices is
guaranteed to be within 95% of its steady-state value within 100
milliseconds after the input voltage has reached 95% of its steadystate value.
80
70
60
50
SAFE OPERATING AREA
40
0
50
90
Total Load Capacitance (uF)
LOAD CAPACITANCE vs INPUT RISE TIME
(15 Vout models)
60
30
20
10
0
0
5
10
15
20
25
30
35
40
45
50
2.) For dual output models, total load capacitance is the sum of the
capacitances on the plus and minus outputs.
Rise Time of Input Voltage (mS)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
HPR1XXVC.B01 Page 3 of 4
HPR1XXVC
0.75 Watt Single Output DC/DC Converter
MECHANICAL
PACKAGE/PINOUT “V”
DIP PACKAGE
0.785±0.010"
(19.94±0.25)
14 13
11 10 9 8
TOP VIEW
0.695±0.015"
(17.65±0.38)
0.525±0.010"
(13.34±0.25)
1 2 3 4 5 6 7
0.375±0.005"
(9.52±0.13)
SIDE VIEW
0.015±0.005"
(0.38±0.13)
0.020±0.002"
(0.51±0.05)
0.100±0.010"
(2.54±0.25)
0.125+0.030"
-0.000"
(3.18+0.76) BOTTOM
(
-0.00)
0°-15°
0.600"
(15.24)
PIN CONNECTIONS
PIN#
1
2
3
4
5
6
SINGLES
+VIN
-VIN
NC
NC
-VOUT
NC
DUALS
PIN#
+VIN
-VIN
NC
NC
-VOUT
Common
7
8
9
10
11
13
14
SINGLES
DUALS
+VOUT
NC
NC
NC
NC
NC
NC
+VOUT
NC
NC
NC
NC
NC
NC
VIEW
NOTES:
NC = Do Not Connect.
Duplicate pin functions are internally connected.
All dimensions are in inches (millimeters).
GRID: 0.100 inches (2.54 millimeters)
MATERIAL: Lead material is phosphor bronze; lead
finish is 100-300 microinches of matte tin over a
nickel barrier layer of 5-40 microinches.
ABSOLUTE MAXIMUM RATINGS
ORDERING INFORMATION
HPR
Internal Power Dissipation ........................................ 450mW
Short Circuit Duration ................................................ Momentary
1XX V
C
Device Family
HPR Indicates DC/DC Converter
Model Number
Selected from Table of Electrical Characteristics
Package Option
V = DIP Package
RoHS Compliant Version
USA:
Mansfield (MA), Tel: (508) 339-3000, email: [email protected]
Canada: Toronto, Tel: (866) 740-1232, email: [email protected]
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected]
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected]
Germany: München, Tel: +49 (0)89-544334-0, email: [email protected]
www.murata-ps.com email: [email protected] ISO 9001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2008 Murata Power Solutions, Inc.
Japan:
Tokyo, Tel: 3-3779-1031, email: [email protected]
Osaka, Tel: 6-6354-2025, email: [email protected]
Website: www.murata-ps.jp
China:
Shanghai, Tel: +86 215 027 3678, email: [email protected]
Guangzhou, Tel: +86 208 221 8066, email: [email protected]
04/17/08
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
HPR1XXVC.B01 Page 4 of 4