LM1036 LM1036 Dual DC Operated Tone/Volume/Balance Circuit Literature Number: SNAS525B LM1036 Dual DC Operated Tone/Volume/Balance Circuit General Description Features The LM1036 is a DC controlled tone (bass/treble), volume and balance circuit for stereo applications in car radio, TV and audio systems. An additional control input allows loudness compensation to be simply effected. Four control inputs provide control of the bass, treble, balance and volume functions through application of DC voltages from a remote control system or, alternatively, from four potentiometers which may be biased from a zener regulated supply provided on the circuit. Each tone response is defined by a single capacitor chosen to give the desired characteristic. ■ ■ ■ ■ ■ ■ Wide supply voltage range, 9V to 16V Large volume control range, 75 dB typical Tone control, ±15 dB typical Channel separation, 75 dB typical Low distortion, 0.06% typical for an input level of 0.3 Vrms High signal to noise, 80 dB typical for an input level of 0.3 Vrms ■ Few external components required Block and Connection Diagram Dual-In-Line (DIP) and Small Outline (SO) Package 514201 Order Number LM1036N, LM1036M or LM1036MX See NS Package Number N20A or M20B © 2008 National Semiconductor Corporation 5142 www.national.com LM1036 Dual DC Operated Tone/Volume/Balance Circuit February 25, 2008 LM1036 Operating Temperature Range Storage Temperature Range Power Dissipation Lead Temp. (Soldering, 10 seconds) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Control Pin Voltage (Pins 4, 7, 9, 12, 14) 0°C to +70°C −65°C to +150°C 1W 260°C Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. 16V VCC Electrical Characteristics VCC=12V, TA=25°C (unless otherwise stated) Parameter Supply Voltage Range Conditions Min Pin 11 9 Supply Current 35 Zener Regulated Output Voltage Current Pin 17 Maximum Output Voltage Pins 8, 13; f=1 kHz VCC=9V, Maximum Gain Maximum Input Voltage Typ Max Units 16 V 45 mA 5 V mA 5.4 0.8 Vrms VCC=12V 0.8 1.0 Vrms Pins 2, 19; f=1 kHz, VCC 2V 1.3 1.6 Vrms 20 30 kΩ Gain=−10 dB Input Resistance Pins 2, 19; f=1 kHz Output Resistance Pins 8, 13; f=1 kHz Maximum Gain V(Pin 12)=V(Pin 17); f=1 kHz −2 0 Volume Control Range f=1 kHz 70 75 Gain Tracking Channel 1–Channel 2 f=1 kHz 0 dB through −40 dB −40 dB through −60 dB Balance Control Range Pins 8, 13; f=1 kHz Bass Control Range f=40 Hz, Cb=0.39 μF (Note 3) V(Pin 14)=V(Pin 17) V(Pin 14)=0V Treble Control Range f= 16 kHz, Ct,=0.01 μF (Note 3) V(Pin 4)=V(Pin 17) V(Pin 4)=0V Total Harmonic Distortion f=1 kHz, VIN=0.3 Vrms 20 1 2 f=1 kHz, Maximum Gain Signal/Noise Ratio Unweighted 100 Hz–20 kHz Maximum Gain, 0 dB=0.3 Vrms CCIR/ARM (Note 4) Gain=0 dB, VIN=0.3 Vrms Output Noise Voltage at Ω dB dB 3 dB dB 1 −26 −20 dB dB 12 −12 15 −15 18 −18 dB dB 12 −12 15 −15 18 −18 dB dB 0.06 0.03 0.3 % % Gain=0 dB Gain=−30 dB Channel Separation 2 60 75 75 dB 80 dB 79 dB Gain=−20 dB, VIN=1.0 Vrms 72 CCIR/ARM (Note 4) 10 dB 16 μV Minimum Gain Supply Ripple Rejection 200 mVrms, 1 kHz Ripple Control Input Currents Pins 4, 7, 9, 12, 14 (V=0V) −0.6 Frequency Response −1 dB (Flat Response 20 Hz–16 kHz) 250 www.national.com 35 2 50 dB −2.5 μA kHz Note 3: The tone control range is defined by capacitors Cb and Ct. See Application Notes. Note 4: Gaussian noise, measured over a period of 50 ms per channel, with a CCIR filter referenced to 2 kHz and an average-responding meter. Typical Performance Characteristics Balance Control Characteristic Volume Control Characteristics 514221 514220 Tone Control Characteristic Tone Characteristic (Gain vs Frequency) 514222 514223 Tone Characteristic (Gain vs Frequency) Loudness Compensated Volume Characteristic 514225 514224 3 www.national.com LM1036 Note 2: The maximum permissible input level is dependent on tone and volume settings. See Application Notes. LM1036 Input Signal Handling vs Supply Voltage THD vs Gain 514227 514226 Channel Separation vs Frequency Loudness Control Characteristic 514229 514228 Output Noise Voltage vs Gain THD vs Input Voltage 514231 514230 www.national.com 4 TONE RESPONSE The maximum boost and cut can be optimized for individual applications by selection of the appropriate values of Ct (treble) and Cb (bass). The tone responses are defined by the relationships: SIGNAL HANDLING The volume control function of the LM1036 is carried out in two stages, controlled by the DC voltage on pin 12, to improve signal handling capability and provide a reduction of output noise level at reduced gain. The first stage is before the tone control processing and provides an initial 15 dB of gain reduction, so ensuring that the tone sections are not overdriven by large input levels when operating with a low volume setting. Any combination of tone and volume settings may be used provided the output level does not exceed 1 Vrms, VCC=12V (0.8 Vrms, VCC=9V). At reduced gain (<−6 dB)the input stage will overload if the input level exceeds 1.6 Vrms, VCC=12V (1.1 Vrms, VCC=9V). As there is volume control on the input stages, the inputs may be operated with a lower overload margin than would otherwise be acceptable, allowing a possible improvement in signal to noise ratio. Where ab=at=0 for maximum bass and treble boost respectively and ab=at=1 for maximum cut. For the values of Cb and Ct of 0.39 μF and 0.01 μF as shown in the Application Circuit, 15 dB of boost or cut is obtained at 40 Hz and 16 kHz. ZENER VOLTAGE A zener voltage (pin 17=5.4V) is provided which may be used to bias the control potentiometers. Setting a DC level of one half of the zener voltage on the control inputs, pins 4, 9, and 14, results in the balanced gain and flat response condition. Typical spread on the zener voltage is ±100 mV and this must be taken into account if control signals are used which are not referenced to the zener voltage. If this is the case, then they will need to be derived with similar accuracy. Application Circuit 514203 5 www.national.com LM1036 LOUDNESS COMPENSATION A simple loudness compensation may be effected by applying a DC control voltage to pin 7. This operates on the tone control stages to produce an additional boost limited by the maximum boost defined by Cb and Ct. There is no loudness compensation when pin 7 is connected to pin 17. Pin 7 can be connected to pin 12 to give the loudness compensated volume characteristic as illustrated without the addition of further external components. (Tone settings are for flat response, Cb and Ct as given in Application Circuit.) Modification to the loudness characteristic is possible by changing the capacitors Cb and Ct for a different basic response or, by a resistor network between pins 7 and 12 for a different threshold and slope. Application Notes LM1036 Applications Information OBTAINING MODIFIED RESPONSE CURVES The LM1036 is a dual DC controlled bass, treble, balance and volume integrated circuit ideal for stereo audio systems. In the various applications where the LM1036 can be used, there may be requirements for responses different to those of the standard application circuit given in the data sheet. This application section details some of the simple variations possible on the standard responses, to assist the choice of optimum characteristics for particular applications. TONE CONTROLS Summarizing the relationship given in the data sheet, basically for an increase in the treble control range Ct must be increased, and for increased bass range Cb must be reduced. Figure 1 shows the typical tone response obtained in the standard application circuit. (Ct=0.01 μF, Cb=0.39 μF). Response curves are given for various amounts of boost and cut. 514206 FIGURE 3. Tone Characteristic (Gain vs Frequency) Figure 4 shows the effect of changing Ct and Cb in the opposite direction to Ct/2, 2Cb respectively giving reduced control ranges. The various results corresponding to the different Ct and Cb values may be mixed if it is required to give a particular emphasis to, for example, the bass control. The particular case with Cb/2, Ct is illustrated in Figure 5. Restriction of Tone Control Action at High or Low Frequencies It may be desired in some applications to level off the tone responses above or below certain frequencies for example to reduce high frequence noise. This may be achieved for the treble response by including a resistor in series with Ct. The treble boost and cut will be 3 dB less than the standard circuit when R=XC. A similar effect may be obtained for the bass response by reducing the value of the AC bypass capacitors on pins 5 (channel 1) and 16 (channel 2). The internal resistance at these pins is 1.3 kΩ and the bass boost/cut will be approximately 3 dB less with XC at this value. An example of such modified response curves is shown in Figure 6. The input coupling capacitors may also modify the low frequency response. It will be seen from Figure 2 and Figure 3 that modifying Ct and Cb for greater control range also has the effect of flattening the tone control extremes and this may be utilized, with or without additional modification as outlined above, for the most suitable tone control range and response shape. 514204 FIGURE 1. Tone Characteristic (Gain vs Frequency) Figure 2 and Figure 3 show the effect of changing the response defining capacitors Ct and Cb to 2Ct, Cb/2 and 4Ct, Cb/4 respectively, giving increased tone control ranges. The values of the bypass capacitors may become significant and affect the lower frequencies in the bass response curves. Other Advantages of DC Controls The DC controls make the addition of other features easy to arrange. For example, the negative-going peaks of the output amplifiers may be detected below a certain level, and used to bias back the bass control from a high boost condition, to prevent overloading the speaker with low frequency components. LOUDNESS CONTROL The loudness control is achieved through control of the tone sections by the voltage applied to pin 7; therefore, the tone and loudness functions are not independent. There is normally 1 dB more bass than treble boost (40 Hz–16 kHz) with loudness control in the standard circuit. If a greater difference is desired, it is necessary to introduce an offset by means of Ct or Cb or by changing the nominal control voltage ranges. Figure 7 shows the typical loudness curves obtained in the standard application circuit at various volume levels (Cb=0.39 μF). 514205 FIGURE 2. Tone Characteristic (Gain vs Frequency) www.national.com 6 514207 FIGURE 4. Tone Characteristic (Gain vs Frequency) 514208 FIGURE 5. Tone Characteristic (Gain vs Frequency) 514211 FIGURE 8. Loudness Compensated Volume Characteristic 514209 FIGURE 6. Tone Characteristic (Gain vs Frequency) 514212 FIGURE 9. Loudness Compensated Volume Characteristic 514210 FIGURE 7. Loudness Compensated Volume Characteristic 7 www.national.com LM1036 Figure 8 and Figure 9 illustrate the loudness characteristics obtained with Cb changed to Cb/2 and Cb/4 respectively, Ct being kept at the nominal 0.01 μF. These values naturally modify the bass tone response as in Figure 2 and Figure 3. With pins 7 (loudness) and 12 (volume) directly connected, loudness control starts at typically −8 dB volume, with most of the control action complete by −30 dB. Figure 10 and Figure 11 show the effect of resistively offsetting the voltage applied to pin 7 towards the control reference voltage (pin 17). Because the control inputs are high impedance, this is easily done and high value resistors may be used for minimal additional loading. It is possible to reduce the rate of onset of control to extend the active range to −50 dB volume control and below. The control on pin 7 may also be divided down towards ground bringing the control action on earlier. This is illustrated in Figure 12, With a suitable level shifting network between pins 12 and 7, the onset of loudness control and its rate of change may be readily modified. LM1036 When adjusted for maximum boost in the usual application circuit, the LM1036 cannot give additional boost from the loudness control with reducing gain. If it is required, some additional boost can be obtained by restricting the tone control range and modifying Ct, Cb, to compensate. A circuit illustrating this for the case of bass boost is shown in Figure 13. The resulting responses are given in Figure 14 showing the continuing loudness control action possible with bass boost previously applied. USE OF THE LM1036 ABOVE AUDIO FREQUENCIES The LM1036 has a basic response typically 1 dB down at 250 kHz (tone controls flat) and therefore by scaling Cb and Ct, it is possible to arrange for operation over a wide frequency range for possible use in wide band equalization applications. As an example Figure 15 shows the responses obtained centered on 10 kHz with Cb=0.039 μF and Ct=0.001 μF. 514213 FIGURE 10. Loudness Compensated Volume Characteristic 514214 FIGURE 11. Loudness Compensated Volume Characteristic 514215 FIGURE 12. Loudness Compensated Volume Characteristic www.national.com 8 LM1036 514216 FIGURE 13. Modified Application Circuit for Additional Bass Boost with Loudness Control 514217 FIGURE 14. Loudness Compensated Volume Characteristic 514218 FIGURE 15. Tone Characteristic (Gain vs Frequency) 9 www.national.com LM1036 Simplified Schematic Diagram (One Channel) 514219 *Connections reversed www.national.com 10 LM1036 Physical Dimensions inches (millimeters) unless otherwise noted Molded Dual-In-Line Package (N) Order Number LM1036N NS Package Number N20A Small Outline (SO) Package Order Number LM1036M or LM1036MX NS Package Number M20B 11 www.national.com LM1036 Dual DC Operated Tone/Volume/Balance Circuit Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated