LME49713 LME49713 High Performance, High Fidelity Current Feedback Audio Operational Amplifier Literature Number: SNAS386E LME49713 High Performance, High Fidelity Current Feedback Audio Operational Amplifier General Description Key Specifications The LME49713 is an ultra-low distortion, low noise, ultra high slew rate current feedback operational amplifier optimized and fully specified for high performance, high fidelity applications. Combining advanced leading-edge process technology with state-of-the-art circuit design, the LME49713 current feedback operational amplifier delivers superior signal amplification for outstanding performance. Operating on a wide supply range of ±5V to ±18V, the LME49713 combines extremely low voltage noise density (1.9nV/√Hz) with very low THD+N (0.00036%) to easily satisfy the most demanding applications. To ensure that the most challenging loads are driven without compromise, the LME49713 has a high slew rate of ±1900V/μs and an output current capability of ±100mA. Further, dynamic range is maximized by an output stage that drives 150Ω loads to within 2.9V of either power supply voltage. The LME49713 's outstanding CMRR (88dB), PSRR (100dB), and VOS (0.05mV) give the amplifier excellent operational amplifier DC performance. The LME49713 is available in an 8–lead narrow body SOIC and 8–lead metal can (TO-99). Demonstration boards are available. ■ Power Supply Voltage Range ±5V to ±18V ■ THD+N, f = 1kHz AV = 1, RL = 100Ω, VOUT = 3VRMS 0.0006% (typ) ■ THD+N, f = 1kHz AV = 1, RL = 600Ω, VOUT = 1.4VRMS 0.00036% (typ) ■ Input Noise Density 1.9nV/√Hz (typ) ■ Slew Rate ±1900V/μs (typ) ■ Bandwidth AV = –1, RL= 2kΩ, RF = 1.2kΩ ■ Input Bias Current ■ Input Offset Voltage 132MHz (typ) 1.8μA (typ) 0.05mV (typ) Features ■ ■ ■ ■ ■ Easily drives 150Ω loads Optimized for superior audio signal fidelity Output short circuit protection 100dB (typ) PSRR and 88dB (typ) CMRR SOIC High Performance and Metal can packages Applications ■ ■ ■ ■ ■ ■ ■ ■ ■ © 2010 National Semiconductor Corporation 202132 Ultra high quality audio amplification High fidelity preamplifiers High fidelity multimedia State of the art phono pre amps High performance professional audio High fidelity equalization and crossover networks High performance line drivers High performance line receivers High fidelity active filters www.national.com LME49713 High Performance, High Fidelity Current Feedback Audio Operational Amplifier June 2, 2010 LME49713 Connection Diagrams SOIC Package LME49713MA Top Mark 20213202 N = National Logo Z = Assembly plant code X = 1 Digit date code TT = Die traceability L49713 = LME49713 MA = Package code 20213201 Order Number LME49713MA See NS Package Number M08A Metal Can 20213222 Order Number LME49713HA See NS Package Number H08C www.national.com 2 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. θJA (MA) Temperature Range Power Supply Voltage (VS = V+ - V-) 38V Storage Temperature −65°C to 150°C Input Voltage (V-) - 0.7V to (V+) + 0.7V Output Short Circuit (Note 3) Internally Limited 2000V 200V 150°C 145°C/W TMIN ≤ TA ≤ TMAX Supply Voltage Range –40°C ≤ TJ ≤ 70°C ±5.0V ≤ VS ≤ ± 18V Continuous Electrical Characteristics (Note 1, Note 2) The following specifications apply for the VS = ±15V, RL = 2kΩ, RSOURCE = 10Ω, fIN = 1kHz, and TJ = 25°C, unless otherwise specified. LME49713 Symbol Parameter Conditions Typical Limit (Note 6) (Note 7) 0.0006 0.00036 0.00071 0.00045 Units (Limits) AV = 1, VOUT = 3VRMS, RF = 1.2kΩ THD+N Total Harmonic Distortion + Noise RL = 100Ω, VOUT = 3VRMS RL = 600Ω, VOUT = 1.4VRMS IMD Intermodulation Distortion AV = 1, VIN = 3VRMS Two-tone, 60Hz & 7kHz 4:1 BW Bandwidth SR FPBW ts % (max) % (max) 0.00009 % AV = –1, RF = 1.2kΩ 132 MHz Slew Rate VO = 20VP-P, AV = –1 ±1900 V/μs Full Power Bandwidth VOUT = 20VP-P, AV = –1 30 MHz Settling time AV = –1, 10V step, 0.1% error range 50 ns Equivalent Input Noise Voltage fBW = 20Hz to 20kHz 0.26 0.6 μVRMS Equivalent Input Noise Density f = 1kHz f = 10Hz 1.9 11.5 4.0 nV/√Hz in Current Noise Density f = 1kHz f = 10Hz 16 160 VOS Input Offset Voltage en ±0.05 Average Input Offset Voltage Drift vs ΔVOS/ΔTemp –40°C ≤ TA ≤ 85°C Temperature (max) (max) pA/√Hz ±1.0 mV (max) μV/°C 0.29 PSRR Average Input Offset Voltage Shift vs VSUPPLY = ±5V to ±15V Power Supply Voltage (Note 8) 100 95 dB (min) IB Input Bias Current VCM = 0V 1.8 6 μA (max) ΔIOS/ΔTemp Input Bias Current Drift vs Temperature –40°C ≤ TA ≤ 85°C Inverting input Non-inverting input 4.5 4.7 IOS Input Offset Current VCM = 0V 1.3 5 μA (max) ±13.5 (V+) – 2.0 (V-) + 2.0 V (min) V (min) –10V<Vcm<10V 88 86 dB (min) Non-inverting-input Input Impedance –10V<Vcm<10V 1.2 MΩ Inverting-input Input Impedance 58 Ω VIN-CM Common-Mode Input Voltage Range CMRR Common-Mode Rejection ZIN –10V<Vcm<10V nA/°C nA/°C VOUT = ±10V ZT Transimpedance VOUTMAX Maximum Output Voltage Swing RL = 200Ω RL = ∞ 4.2 4.7 2.0 2.65 MΩ (min) MΩ (min) RL = 150Ω ±11.1 ±10.3 V (min) RL = 600Ω ±11.6 ±11.4 V (min) 3 www.national.com LME49713 Power Dissipation ESD Rating (Note 4) ESD Rating (Note 5) Junction Temperature Thermal Resistance Absolute Maximum Ratings (Note 1, Note LME49713 LME49713 Symbol Parameter IOUT Output Current IOUT-CC Instantaneous Short Circuit Current ROUT IS Conditions RL = 150Ω, VS = ±18V Typical Limit (Note 6) (Note 7) ±100 ±91 ±140 Output Resistance fIN = 5MHz, Open-Loop 10 Total Quiescent Current IOUT = 0mA 8.5 Units (Limits) mA (min) mA Ω 10 mA (max) Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: Amplifier output connected to GND, any number of amplifiers within a package. Note 4: Human body model, applicable std. JESD22-A114C. Note 5: Machine model, applicable std. JESD22-A115-A. Note 6: Typical values represent most likely parametric norms at TA = +25ºC, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 7: Datasheet min/max specification limits are guaranteed by test or statistical analysis. Note 8: PSRR is measured as follows: VOS is measured at two supply voltages, ±5V and ±15V. PSRR = | 20log(ΔVOS/ΔVS) |. www.national.com 4 THD FFT vs Frequency VO = 3VRMS, RL = 1kΩ, VS = ±15V, AV = 1 THD FFT vs Frequency VO = 3VRMS, RL = 100Ω, VS = ±15V, AV = 1 20213219 20213220 THD FFT vs Frequency VO = 3VRMS, RL = 600Ω, VS = ±15V, AV = 1 THD FFT vs Frequency VO1 = 1.4VRMS, RL = 1kΩ, VS = ±15V, AV = 1 20213221 20213216 THD FFT vs Frequency VO1 = 1.4VRMS, RL = 100Ω, VS = ±15V, AV = 1 THD FFT vs Frequency AV =1. 4VRMS, RL = 600Ω, VS = ±15V, AV = 1 20213217 20213218 5 www.national.com LME49713 Typical Performance Characteristics LME49713 THD vs Frequency VO = 3VRMS, RL = 100Ω, SOIC THD vs Frequency VO = 3VRMS, RL = 600Ω, SOIC 202132p6 202132p5 THD vs Frequency VO = 3VRMS, RL = 100Ω THD vs Output Voltage VO = 3VRMS, RL = 600Ω 202132p7 202132p8 THD vs RF Output Voltage vs Supply Voltage AV = 1, RL = 600Ω 202132p9 20213212 www.national.com 6 Supply Current (ICC) vs Power Supply RL = open 20213213 20213214 Supply Current (IEE) vs Power Supply RL = open Gain vs Frequency VS = ±15V, G = –1 20213204 20213215 Gain vs Frequency VS = ±15V, G = –2 Gain vs Frequency VS = ±15V, G = –5 20213205 20213206 7 www.national.com LME49713 Output Voltage vs Supply Voltage AV = 1, RL = open LME49713 Gain vs Frequency VS = ±15V, G = –10 Gain vs Frequency RF = 800Ω, VS = ±15V 20213207 20213208 Gain vs Frequency RF = 1.2kΩ, VS = ±15V Gain vs Frequency RF = 2kΩ, VS = ±15V 20213210 20213209 Gain vs Frequency RF = 3kΩ, VS = ±15V CMRR vs Frequency VS= ±15V 202132p0 20213211 www.national.com 8 LME49713 PSRR vs Frequency VS= ±15V, VRIPPLE = 200mVP-P Current Noise vs Frequency VS= ±15V 202132p1 202132p3 Equivalent Voltage Noise vs Frequency VS= ±15V Slew Rate vs Output Voltage VS= ±15V 202132p2 202132p4 9 www.national.com LME49713 SLEW RATE CONSIDERATIONS A current feedback amplifier’s slew rate characteristics are different than that of voltage feedback amplifiers. A voltage feedback amplifier’s slew rate limiting or non-linear amplifier behavior is dominated by the finite availability of the first stage tail current charging the second stage voltage amplifier’s compensation capacitor. Conversely, a current feedback amplifier’s slew rate is not constant. Transient current at the inverting input determines slew rate for both inverting and non-inverting gains. The non-inverting configuration slew rate is also determined by input stage limitations. Accordingly, variations of slew rates occur for different circuit topologies. Application Information GENERAL AMPLIFIER FUNCTION Voltage feedback amplifiers have a small-signal bandwidth that is a function of the closed-loop gain. Conversely, the LME49713 current feedback amplifier features a small-signal bandwidth that is relatively independent of the closed-loop gain. This is shown in Figure 1 where the LME49713’s gain is –1,–2, –5 and –10. Like all current feedback amplifiers, the LME49713’s closed-loop bandwidth is a function of the feedback resistance value. Therefore, Rs must be varied to select the desired closed-loop gain. DRIVING CAPACITIVE LOADS The LME49713 can drive significantly higher capacitive loads than many current feedback amplifiers. Although the LME49713 can directly drive as much as 100pF without oscillating, the resulting response will be a function of the feedback resistor value. POWER SUPPLY BYPASSING AND LAYOUT CONSIDERATIONS Properly placed and correctly valued supply bypassing is essential for optimized high-speed amplifier operation. The supply bypassing must maintain a wideband, low-impedance capacitive connection between the amplifier’s supply pin and ground. This helps preserve high speed signal and fast transient fidelity. The bypassing is easily accomplished using a parallel combination of a 10μF tantalum and a 0.1μF ceramic capacitors for each power supply pin. The bypass capacitors should be placed as close to the amplifier power supply pins as possible. CAPACITIVE FEEDBACK It is quite common to place a small lead-compensation capacitor in parallel with a voltage feedback amplifier’s feedback resistance, Rf. This compensation reduces the amplifier’s peaking in the frequency domain and damps the transient response. Whereas this yields the expected results when used with voltage feedback amplifiers, this technique must not be used with current feedback amplifiers. The dynamic impedance of capacitors in the feedback loop reduces the amplifier’s stability. Instead, reduced peaking in the frequency response and bandwidth limiting can be accomplished by adding an RC circuit to the amplifier’s input. FEEDBACK RESISTOR SELECTION (Rf) The value of the Rf, is also a dominant factor in compensating the LME49713. For general applications, the LME49713 will maintain specified performance with an 1.2kΩ feedback resistor. Although this value will provide good results for most applications, it may be advantageous to adjust this value slightly for best pulse response optimized for the desired bandwidth. In addition to reducing bandwidth, increasing the feedback resistor value also reduces overshoot in the time domain response. 20213209 FIGURE 1. Bandwidth as a function of gain www.national.com 10 LME49713 Revision History Rev Date 1.0 09/26/07 Description Initial release. 1.1 09/28/07 Added the Typical Performance curves. 1.2 10/03/07 Input Limit values. 1.3 10/29/07 Edited the Specification table, typical performance curve, and text edits. 1.4 01/29/08 Added more curves in the Typical Performance section. 1.5 07/24/08 Added the Metal Can package. 1.6 08/20/08 Text edits (updated some of the curves' titles). 1.7 08/22/08 Text edits. 1.8 02/08/10 Input changes on typical and limits in the EC table. 1.9 04/23/10 Input Typical and Limit edits on THD+N and IOUT in the EC table. 2.0 06/02/10 Input text edits on the first page. 11 www.national.com LME49713 Physical Dimensions inches (millimeters) unless otherwise noted SOIC Package Order Number LME49713MA NS Package Number M08A Metal Can Order Number LME49713HA NS Package Number H08C www.national.com 12 LME49713 Notes 13 www.national.com LME49713 High Performance, High Fidelity Current Feedback Audio Operational Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated