LMC1983 Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs General Description The LMC1983 is a monolithic integrated circuit that provides volume, balance, tone (bass and treble), loudness controls and selection between three pairs of stereo inputs. These functions are digitally controlled through a three-wire communication interface. There are two digital inputs for easy interface to other audio peripherals such as stereo decoders. The LMC1983 is designed for line level input signals (300 mV–2V) and has a maximum gain of −0.5 dB. Volume is set at minimum and tone controls are flat when supply voltage is first applied. Low noise and distortion result from using analog switches and poly-silicon resistor networks in the signal path. Additional tone control can be achieved using the LMC835 stereo 7-band graphic equalizer connected to the LMC1983’s SELECT OUT/SELECT IN external processor loop. Features n Low noise and distortion n n n n n n n n n n n Three pairs of stereo inputs Loudness compensation 40 position 2 dB/step volume attenuator plus mute Independent left and right volume controls Low noise-suitable for use with DNR ® and Dolby ® noise reduction External processor loop Signal handling suitable for compact discs Pop-free switching Serially programmable: INTERMETAL bus (IM) interface 6V to 12V single supply operation 28 Pin DIP or PLCC Package Applications n n n n n Stereo television Music reproduction systems Sound reinforcement systems Electronic music (MIDI) Personal computer audio control Block Diagram DS011279-1 DNR ® is a registered trademark of National Semiconductor Corporation. Dolby ® is a registered trademark of Dolby Labs. © 1999 National Semiconductor Corporation DS011279 www.national.com LMC1983 Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs August 1992 Absolute Maximum Ratings (Notes 1, Lead Temperature N Package, (Soldering, 10 Seconds) V Package, (Vapor Phase, 60 Seconds) Infrared, (15 Seconds) ESD Susceptability (Note 5) 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V+ − GND) Voltage at any Pin Input Current at any Pin (Note 3) Package Input Current (Note 3) Power Dissipation (Note 4) Junction Temperature Storage Temperature 15V GND − 0.2V to V+ + 0.2V +260˚C 215˚C 220˚C 2 kV Operating Ratings (Notes 1, 2) 5 mA 20 mA 500 mW +125˚C −65˚C to +150˚C Temperature Range LMC1983CIN, LMC1983CIV Supply Voltage Range (V+ − V−) TMIN ≤ TA ≤ TMAX −40˚C ≤ TA ≤ +85˚C 6V to 12V Electrical Characteristics The following specifications apply for V+ = 9V, fIN = 1 kHz, input signal (300 mV) applied to INPUT 1, volume = 0 dB, bass = 0 dB, treble = 0 dB, and loudness is off unless otherwise specified. All limits apply for TA = TJ = +25˚C. Symbol Parameter Conditions IS Supply Current VIN Input Voltage Clipping Level (1.0% THD), THD Total Harmonic Distortion Left and Right channels; Typical Limit Unit (Note 6) (Note 7) (Limit) 15 25 mA (max) 2.3 2.0 Vrms (min) 0.008 0.1 % (max) 0.4 1.0 % (max) 0.5 1.0 % (max) 0.07 0.5 % (max) Select Out (Pins 7, 22) Output Pins 13, 16 VIN = 0.3 Vrms; fIN = 100 Hz, 1 kHz, 10 kHz VIN = 2.0 Vrms; fIN = 100 Hz, 1 kHz VIN = 2.0 Vrms; fIN = 10 kHz VIN = 0.5 Vrms; Bass and Treble Tone Controls Set at Maximum VIN = 0.3 Vrms; Volume 0.06 0.15 % (max) Tone Controls Set at Maximum VIN = 0.3 Vrms; between Any 2.0 4.0 mV (max) Two Adjacent Control Settings VIN = 0.3 Vrms; 18 20 mV (max) Pins 7, 22, (470Ω to Ground at Input) 150 200 Ω (max) Pins 13, 16 26 40 Ω (max) AC Input Impedance Pins 4, 5, 23, 24, 25 50 72 kΩ (max) 35 kΩ (min) Volume Attenuator Range Pins 13, 16; Volume 0.5 1.5 dB (max) Attenuator at −20 dB, Bass and Treble DC Shifts All Mode and Input Positions ROUT RIN AC Output Impedance Attenuation at 0100010XXX000000 (0 dB) 0100010XXX101XXX (80 dB); 80 (Relative to Attenuation at 78 dB (min) 82 dB (max) the 0 dB Setting) Volume Step Size All Volume Attenuation Settings from 0100010XXX101XXX (80 dB) to 0100010XXX000000 (0 dB) (Note 9) www.national.com 2 2.0 1.5 dB (min) 2.5 dB (min) Electrical Characteristics (Continued) The following specifications apply for V+ = 9V, fIN = 1 kHz, input signal (300 mV) applied to INPUT 1, volume = 0 dB, bass = 0 dB, treble = 0 dB, and loudness is off unless otherwise specified. All limits apply for TA = TJ = +25˚C. Symbol Parameter Conditions Typical Limit Unit (Note 6) (Note 7) (Limit) ± 0.1 ± 1.5 dB (min) ± 2.0 dB (min) 105 86 dB (max) ± 12 dB (max) ± 0.1 ± 10.0 ± 14.0 ± 1.5 2.0 1.5 dB (min) 2.5 dB (max) dB (max) ± 0.1 ± 10.0 ± 14.0 ± 1.5 2.0 1.5 dB (min) 2.5 dB (max) ± 0.1 ± 1.0 dB (max) 11.5 13.5 dB (max) All Volume Attenuation Settings from Channel-to-Channel 0100010XXX100110 (76 dB) to Tracking Error 0100010XXX000000 (0 dB) from 0100010XXX101XXX (80 dB) to 0100010XXX100111 (78 dB) Mute Attenuation Bass Gain Range VIN = 1.0 Vrms fIN = 100 Hz, Pins 13, 16 Bass Step Size fIN = 100 Hz, Pins 13, 16 fIN = 100 Hz, Pins 13, 16 Treble Gain Range (Relative to Previous Level) fIN = 10 kHz, Pins 13, 16 Bass Tracking Error Treble Tracking Error Treble Step Size fIN = 10 kHz, Pins 13, 16 fIN = 10 kHz, Pins 13, 16 ± 12 (Relative to Previous Level) Frequency Response Loudness VIN Applied to Input 1 and Input 2; fIN = 20 Hz − 20 kHz dB (min) dB (max) dB (min) dB (max) (Relative to Signal Amplitude at 1 kHz) Volume Attenuator = 40 dB, Loudness on (See Figure 5 ) Gain at 100 Hz (Referenced to Gain at 1 kHz) 9.5 dB (min) 8.5 dB (max) Gain at 10 kHz (Referenced 6.5 to Gain at 1 kHz) VIN = 1.0 Vrms, A Weighted, Measured at 1 kHz, RS = 470Ω 4.5 dB (min) Signal-to-Noise Ratio 95 90 dB (min) Channel Balance All Volume Settings 0.2 1.0 dB (max) Channel Separation Input Pins 4, 25: Output Pins 13, 16; VIN = 1.0 Vrms (Note 8) 80 60 dB (min) Input-Input Isolation 470Ω to AC Ground on Unused Input V+ = 9 VDC; 200 mVrms, 100 Hz Sinewave Applied to Pin 26 95 60 dB (min) 32 28 dB (min) PSSR Power Supply Rejection Ratio fCLK Clock Frequency VIN(1) Logic “1” Input Voltage 5.0 1.0 MHz (max) Pins 1, 27, 28 (IM Bus) 1.3 2.0 V (min) Pins 2, 3 2.9 5.5 V (min) 0.8 V (max) 3.5 V (max) VIN(0) Logic “0” Input Voltage Pins 1, 27, 28 (IM Bus) 0.4 Pins 2, 3 1.2 VOUT(1) Logic “1” Output Voltage Pin 28 (IM Bus) VOUT(0) Logic “0” Output Voltage Pin 28 (IM Bus) 0.4 2.0 V (min) 0.8 V (max) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the deivce may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are specified with respect to ground. Note 3: When the input voltage (VIN) at any pin exceeds the power supply voltages (VIN < V− or VIN > V+) the absolute value of the current at that pin should be limited to 5 mA or less. The 20 mA package input current limits the number of pins that can exceed the power supply voltages with 5 mA current limit to four. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum allowable power dissipation is PD = (TJMAX − TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LMC1983CIN, TJMAX = +125˚C, and the typical junction-to-ambient thermal resistance, when board mounted, is 67˚C/W. 3 www.national.com Electrical Characteristics (Continued) Note 5: Human body model; 100 pF discharged through a 1.5 kΩ resistor. Note 6: Typicals are at TJ = +25˚C and represent the most likely parametric norm. Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: The Input-Input Isolation is tested by driving one input and measuring the output when the undriven input are selected. Note 9: The Volume Step Size is defined as the change in attenuation between any two adjacent volume attenuation settings. The nominal Volume Step Size is 2 dB. Typical Performance Characteristics Supply Current vs Supply Voltage Output Voltage vs Supply Voltage DS011279-11 THD vs Load Impedance THD vs Load Impedance DS011279-12 CCIR Output Noise vs Volume Setting DS011279-14 THD vs VIN (VOUT Constant) DS011279-13 Channel Separation vs Frequency DS011279-15 DS011279-16 Mute Gain vs Frequency THD vs Frequency DS011279-18 DS011279-17 www.national.com DS011279-19 4 Typical Performance Characteristics Tone Control Response with Equal Bass and Treble Control Settings (Continued) Loudness Response vs Frequency Select Input Impedance vs Frequency DS011279-21 DS011279-22 DS011279-20 Connection Diagram DS011279-2 Top View Order Number LMC1983CIN See NS Package Number N28B DS011279-10 Top View Order Number LMC1983CIV See NS Package Number V28A 5 www.national.com Pin Description CLK (1) The INTERMETAL (IM) Bus clock is applied to the CLOCK pin. This input accepts a TTL or CMOS level signal. The input is used to clock the DATA signal. A data bit must be valid on the rising clock edge. DIGITAL INPUT Internally tied high to V+ through a 1 & 2 (2, 3) 30 kΩ pull-up resistor, these inputs allow a peripheral device to place any single-bit, active low digital information onto the IM Bus. It is then sent out to the controlling device through the DATA pin. Examples of such information could include indication of the presence of a Second Audio Program (SAP) or an FM stereo carrier. INPUTS 1, 2 & 3 These are the LMC1983’s three stereo (4, 25; 5, 24; 6, 23) input pairs. SELECT OUT The selected INPUT signal is available (7, 22) at this output. This feature allows external signal processors such as noise reduction or graphic equalizers to be used. This output can typically sink 1 mA. These pins should be capacitively coupled to pins 8 and 21, respectively, if no external processor is used. SELECT IN These are the inputs that an external (8, 21) signal processor uses to return a signal to the LMC1983. These pins should be capacitively coupled to pins 7 and 22, respectively, if no external processor is used. TONE IN These are the inputs to the tone con(9, 20) trol amplifier. See the Application Information section titled “Tone Control Response”. TONE OUT Tone control amplifier output. See the (10, 19) Application Information section titled “Tone Control Response”. OP AMP These outputs are used with external OUT (11, 18) tone control capacitors. Internally, this output is applied to the volume attenuators. LOUDNESS The output signal on these pins is a (12, 17) voltage taken from the volume attenuator’s −40 dB tap point. An external R–C network is connected to these pins. The output signal from these pins MAIN drives a stereo power amplifier. The OUTPUT output can typically sink 1 mA. (13, 16) BYPASS (14) A 10 µF capacitor is connected be- www.national.com GROUND (15) V+ (26) ID (27) DATA (28) tween this pin and ground to provide an AC ground for the internal half-supply voltage reference. This pin is connected to analog ground. This is the power supply connection. The LMC1983 is operational with supply voltages from 6V to 12V. This pin should be bypassed to ground through a 1.0 µF capacitor. This is the IDENTITY digital input that, when low, signals the LMC1983 to receive, from a controlling device, a device address (40H–47H), present on the DATA line. This is the serial data input for communications sent by a controller. The controller must have open drain outputs used with external pull-up resistors. The data rate has a maximum frequency of 1 MHz. The LMC1983 requires 16 bits of data to control or change a function: the first 8 bits select the LMC1983 and one of eight functions. The final eight bits set the function to a desired value. The data must be valid on the rising edge of the CLOCK input signal. General Information The LMC1983 is a CMOS/bipolar building block intended for high fidelity audio signal processing. It is designed for line level inputs signals (300 mV − 2V) and has a maximum gain of −0.5 dB. While the LMC1983 is manufactured with CMOS processing, NPN transistors are used to build low noise op amps. The combination of CMOS switches, bipolar op amps, and poly-silicon resistors make it possible to achieve an order of magnitude quality improvement over other bipolar circuits that use analog multipliers to accomplish gain adjustment. Internal circuits set the volume to minimum, tone controls to flat, the mute to on, and all other functions off when power is first applied. Individual left and right volume controls are software programmed to achieve the stereo balance function. Figure 1 shows the connection diagram of a typical LMC1983 application. The LMC1983 has internal decoding logic that allows a microprocessor (µP) or microcontroller (µC) to communicate directly to the audio control circuitry through an INTERMETAL (IM) Bus interface. This three-wire interface consists of a bi-directional DATA line, a Clock (CLK) input line, and an Identity (ID) line. Address and function selection data (8 bits) are serially shifted from the controller to the LMC1983. This is followed by 8 bits of function value data. Data present in the internal shift register is latched and the instruction is executed. 6 General Information (Continued) DS011279-3 FIGURE 1. Typical Application Application Information The output signal at pins 7 and 22 can be used to drive exteral audio processing circuits such as noise reduction (LM1894–DNR or Dolby) or graphic equalizers (LMC835). It is important that if any noise reduction is used it be placed ahead of any tone controls or equalizers in the external circuit path to preserve the frequency spectrum of the selected input signal. Otherwise, any frequency equalization could prevent the proper operation of the noise reduction circuit. If no external processor is used, a capacitor should be used to couple the SELECT OUT signals directly to pins 8 and 21, respectively. INPUT SELECTOR The LMC1983’s input selector and mode control are shown in Figure 2. The input selector selects one of three stereo signal sources or a mute function with typical attenuation of 100 dB. The selected signals are then sent to a mode control matrix. As shown in Table 1, the matrix provides normal stereo or can direct any given channel to both LEFT or RIGHT SELECT OUTPUTs. The third matrix mode is normal stereo. The control matrix output is buffered and appears on each channel’s respective SELECT OUT pin (7, 22). Switching noise is kept to a minimum when mute is selected by using a 50 kΩ bias resistor. Noise performance is optimized through the use of emitter followers in the mode control matrix’s output. Internal 50 kΩ resistors are connected to each input selector pin to provide the proper bias point for the emitter follower buffers. Each internal 50 kΩ bias resistor is connected to a common half-supply (V+/2) source. This produces a voltage at pins 7 and 22 (SELECT OUT) that is 1.4V below V+/2 (typically 3.1V with V+ = 9V). Since a DC voltage is present at the input pins (4, 5, 6, 23, 24, and 25), input signals should be AC coupled through a 1 µF capacitor. MINIMUM LOAD IMPEDANCE The LMC1983 employs emitter-followers to buffer the selected stereo channels. The buffered signals are available at pins 7 and 22 (SELECT OUT). The SELECT OUT buffers operate with a typical bias current of 1 mA. The Electrical Specifications table lists a maximum input signal of 2.0 Vrms (2.8 Vpeak) for 1% THD at the SELECT OUT pins. This distortion level is achieved when the minimum AC load impedance seen by the SELECT OUT pins is 2.5 kΩ (2.5V/1 mA). Using lower load impedances results in clipping 7 www.national.com Application Information The SELECT IN pins have an input impedance that varies with the BASS and TREBLE control settings. The input impedance is 100 kΩ at DC and 19 kΩ at 1 kHz when the controls are set at 0 dB. Minimum input impedance of 30.4 kΩ at DC and 16 kΩ at 1 kHz occurs when maximum boost is selected. At 10 kHz the minimum input impedance, with the tone controls flat, is 6.8 kΩ and, with the tone controls at maximum boost, is 2.5 kΩ. (Continued) at lower output levels. If the load impedance is DC-coupled, an increased quiescent current can flow. Latch-up may occur if the total emitter current exceeds 5 mA. Thus, maximum output voltage can be increased and much lower distortion levels can be achieved using load impedances of at least 25 kΩ. INPUT IMPEDANCE The input impedance of pins 4, 5, 6, 23, 24 and 25 is defined by internal bias resistors and is typically 50 kΩ. DS011279-4 FIGURE 2. Input and Mode Select Circuitry www.national.com 8 Application Information (Continued) TABLE 1. IM Bus Programming Codes for LMC1983 Address Function Data Input Select + Mute XXXXXX00 INPUT1 XXXXXX01 INPUT2 XXXXXX10 INPUT3 (A7–A0) 01000000 Selected 01000001 Loudness 01000010 Bass 01000011 01000100 01000101 01000110 01000111 Function Treble Left Volume Right Volume Mode Select Read Digital Input 1 XXXXXX11 MUTE XXXXXXX0 Loudness OFF XXXXXXX1 Loudness ON XXXX0000 −12 dB XXXX0011 −6 dB XXXX0110 FLAT XXXX1001 +6 dB XXXX11XX +12 dB XXXX0000 −12 dB XXXX0011 −6 dB XXXX0110 FLAT XXXX1001 +6 dB XXXX11XX +12 dB XX000000 0 dB XX010100 −40 dB XX101XXX −80 dB XX11XXXX −80 dB XX000000 0 dB XX010100 −40 dB XX101XXX −80 dB XX11XXXX −80 dB XXXXX100 Left Mono XXXXX101 Stereo XXXXX11X Right Mono D0 = Digital Input 1 D1 = Digital Input 2 XXXXXXD1D0 or Digital Input 2 on IM Bus 9 www.national.com Application Information C3 and C2 sets the mid-frequency gain. Symmetrical tone response is achieved when C2 = C3. However, with C2 = 2(C3) and the tone controls set to “flat”, the frequency response will be flat at 20 Hz and 20 kHz, and +6 dB at 1 kHz. (Continued) EXTERNAL SIGNAL PROCESSING The SELECT OUT pins (7 and 22) enable greater system design flexibility by providing a means to implement an external processing loop. This loop can be used for noise reduction circuits such as DNR (LM1894) or multi-band graphic equalizers (LMC835). If both are used, it is important to ensure that the noise reduction circuitry precede the equalization circuits. Failure to do so results in improper operation of the noise reduction circuits. The system shown in Figure 3 utilizes the external loop to include DNR and a multi-band equalizer. The frequency where a tone control begins to deviate from a flat response is referred to as the turn-over frequency. With C = C2 = C3, the LMC1983’s treble turn-over frequency is nominally The bass turn-over frequency is nominally TONE CONTROL RESPONSE Bass and treble tone controls are included in the LMC1983. The tone controls use just two external capacitors for each stereo channel. Each has a corner frequency determined by the value of C2 and C3 (see Figure 4 ) and internal resistors in the feedback loop of the internal tone amplifier. The maximum-boost or cut is determined by the data sent to the LMC1983 (see Table 1). The typical tone control response shown in Typical Performance Curves were generated with C2 = C3 = 0.0082 µF and show the response for each step. When modifying the tone control response it is important to note that the ratio of when maximum boost is chosen. The inflection points (the frequencies where the boost or cut is within 3 dB of the final value) are for treble and bass DS011279-5 FIGURE 3. System Block Diagram Utilizing the External Processing Loop (One Channel Shown) www.national.com 10 Application Information The LMC1983’s loudness function uses external components R1, R2, C4 and C5, as shown in Figure 5, to select the frequencies where bass and treble boost begin. The amount of boost is dependent on the volume attenuator’s setting. The loudness characteristic, with the volume attenuator set at 40 dB, has a transfer function of (Continued) The external components R1 and C4 can be eliminated and pin 11(18) left open if bass boost is the only desired loudness characteristic. DS011279-6 FIGURE 4. The Tone Control Amplifier Increasing the values of C2 and C3 decreases the turnover and inflection frequencies: i.e., the Tone Control Response Curves shown in Typical Performance Curves will shift left when C2 and C3 are increased and shift right when C2 and C3 are decreased. With C2 = C3 = 0.0082, 2 dB steps are achieved at 100 Hz and 10 kHz. Changing C2 and C3 to 0.01 µF shifts the 2 dB per step frequency to 72 Hz and 8.3 kHz. If the tone control capacitors’ size is decreased these frequencies will increase. With C2 = C3 = 0.0068 µF the 2 dB steps take place at 130 Hz and 11.2 kHz. DS011279-7 FIGURE 5. Loudness Control Circuit SERIAL DATA COMMUNICATION The LMC1983 uses the INTERMETAL serial bus (IM Bus) standard. Serial data information is sent to the LMC1983 over a three wire IM Bus consisting of Clock (CLK), Data (DATA), and Identity (ID). The DATA line is bidirectional and the CLK and ID lines are unidirectional from the microprocessor or micontroller to the LMC1983. The LMC1983’s bidirectional capability is accomplished by using an open drain output on the DATA line and an external 1 kΩ pull-up resistor. The LMC1983 responds to address values from 01000000 (40H) through 01000111 (47H). The addresses select one of the eight available functions (see Table 1). The IM Bus’ lines have a logic high standby state when using TTL logic levels. As shown in Figure 6, data transmission is initiated by low levels on CLK and ID. Next, eight address bits are sent. This address information includes the code to select one of the LMC1983’s desired functions. Each address bit is clocked in on the rising edge of CLK. The ID line is taken high after the eight bits of address data are received by the LMC1983. LOUDNESS The human ear has less sensitivity to high and low frequencies relative to its sensitivity to mid-range frequencies between 2 kHz and 6 kHz for any given acoustic level. The low and high frequency sensitivity decreases faster than the sensitivity to the mid-range frequencies as the acoustic level drops. The LMC1983’s loudness function can be used to help compensate for the decreased sensitivity by boosting the gain at low and high frequencies as the volume control attenuation increases (see the curve labeled “Gain vs Frequency with Loudness Active”). DS011279-8 FIGURE 6. LMC1983’s INTERMETAL Serial Bus Timing Table 1 also details the serial data structure, range, and bit assignments that sets each function’s operating point. The volume and tone controls’ function control data binarily increments from zero to maximum as the function’s operating point changes from 80 dB attenuation to 0 dB attenuation (volume) or −12 dB to +12 dB (tone controls). Note that not all data bits are needed by each function. The extra bits shown as “X”s (“don’t cares”) are position holders and have The controlling system continues toggling the CLK line eight more times. Data that determines the selected function’s operating point is written into, or single bit information on DIGITAL INPUT 1 or DIGITAL INPUT 2 is read from, the LMC1983. Finally, the end of transmission is signaled by pulsing the ID line low for a minimum of 3 µs. The transmitted function data is latched and the function changes to its new setting. 11 www.national.com Application Information DIGITAL I/O (Continued) The LMC1983’s two Digital Input pins, 2 and 3, provide single-bit communication between a peripheral device and the controller over the IM Bus. Each pin has an internal 30 kΩ pull-up resistor. Therefore, these pins should be connected to open collector/drain outputs. The type of information that could be received on these lines and retrieved by a controller include FM stereo pilot indication, power on/off, Secondary Audio Program (SAP), etc. According to Table 1, the logic state of DIGITAL INPUT 1 and DIGITAL INPUT 2 is latched and can be retrieved over the IM Bus using the read command (47H). The single-bit information sent on the IM Bus is active low since these lines are internally pulled high. no affect on a respective control. They are necessary to properly position the data in the LMC1983’s internal data shift register. Unexpected results may take place if these bits are not sent. The LMC1983’s internal data shift register can handle either a 16-bit word or two 8-bit serial data transmissions. It is the final 8 bits of data received before the ID line goes high that are used as the LMC1983 selection and function addresses. The final eight bits after the ID line returns high are used to change a function’s operating point. CLK must be stopped when the final 8 data bits are received. The data stored in the internal data latch remains unchanged until the ID is pulsed, signifying the end of data transmission. When ID is pulsed, the new data in the data shift register is latched into the data latch and the selected function takes on a new operating point. A complete description and more information concerning the IM Bus is given in the appendix of ITT’s CCU2000 datasheet. www.national.com 12 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LMC1983CIN NS Package Number N28B Order Number LMC1983CIV NS Package Number V28A 13 www.national.com LMC1983 Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.