TI UC1848

application
INFO
available
UC1848
UC2848
UC3848
Average Current Mode PWM Controller
FEATURES
BLOCK DIAGRAM
• Practical Primary Side Control of
Isolated Power Supplies with DC
Control of Secondary Side Current
• Accurate Programmable Maximum
Duty Cycle Clamp
• Maximum Volt-Second Product Clamp
to Prevent Core Saturation
• Practical Operation Up to 1MHz
• High Current (2A Pk) Totem Pole
Output Driver
• Wide Bandwidth (8MHz) Current Error
Amplifier
• Under Voltage Lockout Monitors VCC,
VIN and VREF
• Output Active Low During UVLO
• Low Startup Current (500µA)
• Precision 5V Reference (1%)
UDG-93003-1
DESCRIPTION
The UC3848 family of PWM control ICs makes primary
side average current mode control practical for isolated
switching converters. Average current mode control insures that both cycle by cycle peak switch current and
maximum average inductor current are well defined and
will not run away in a short circuit situation. The UC3848
can be used to control a wide variety of converter topologies.
In addition to the basic functions required for pulse width
modulation, the UC3848 implements a patented technique of sensing secondary current in an isolated buck
derived converter from the primary side. A current waveform synthesizer monitors switch current and simulates
the inductor current down slope so that the complete current waveform can be constructed on the primary side
without actual secondary side measurement. This information on the primary side allows for full DC control of
output current.
The UC3848 circuitry includes a precision reference, a
wide bandwidth error amplifier for average current control, an oscillator to generate the system clock, latching
PWM comparator and logic circuits, and a high current
SLUS225A - April 1996 - REVISED MARCH 2004
output driver. The current error amplifier easily interfaces
with an optoisolator from a secondary side voltage sensing circuit.
A full featured undervoltage lockout (UVLO) circuit is contained in the UC3848. UVLO monitors the supply voltage
to the controller (VCC), the reference voltage (VREF),
and the input line voltage (VIN). All three must be good
before soft start commences. If either VCC or VIN is low,
the supply current required by the chip is only 500µA and
the output is actively held low.
Two on board protection features set controlled limits to
prevent transformer core saturation. Input voltage is monitored and pulse width is constrained to limit the maximum volt-second product applied to the transformer. A
unique patented technique limits maximum duty cycle
within 3% of a user programmed value.
These two features allow for more optimal use of transformers and switches, resulting in reduced system size
and cost.
Patents embodied in the UC3848 belong to Lambda
Electronics Incorporated and are licensed for use in applications employing these devices.
UC1848
UC2848
UC3848
ABSOLUTE MAXIMUM RATINGS
Analog Output Currents, Source or Sink (Pins 5 & 10) . . . 5mA
Power Dissipation at TA = 60°C . . . . . . . . . . . . . . . . . . . . . . 1W
Storage Temperature Range . . . . . . . . . . . . . . . −65°C to +150°C
Lead Temperature (Soldering 10 seconds) . . . . . . . . . . +300°C
Supply Voltage (Pin 15). . . . . . . . . . . . . . . . . . . . . . . . . . . . 22V
Output Current, Source or Sink (Pin 14)
DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A
Pulse (0.5 s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2A
Power Ground to Ground (Pin 1 to Pin 13) . . . . . . . . . . . ± 0.2V
Analog Input Voltages
(Pins 3, 4, 7, 8, 12, 16) . . . . . . . . . . . . . . . . . . . . . –0.3 to 7V
Analog Input Currents, Source or Sink
(Pins 3, 4, 7, 8, 11, 12, 16) . . . . . . . . . . . . . . . . . . . . . . 1mA
CONNECTION DIAGRAMS
PLCC-20 & LCC-20
(Top View)
Q & L Packages
DIL-16, SOIC-16 (Top View)
J, N, or DW Packages
PACKAGE PIN FUNCTION
FUNCTION
PIN
N/C
1
GND
2
VREF
3
NI
4
INV
5
N/C
6
CAO
7
CT
8
VS
9
DMAX
10
N/C
11
CDC
12
CI
13
IOFF
14
ION
15
N/C
16
PGND
17
OUT
18
VCC
19
UV
20
THERMAL RATINGS TABLE
Package
DIL-16J
DIL-16N
SOIC-16DW
PLCC-20
LCC-20
QJA
80-120
90(1)
50-100(1)
43-75(1)
70-80
QJC
28(2)
45
27
34
20(2)(3)
Q
Q
Q
2
UC1848
UC2848
UC3848
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, all specifications are over the junction temperature range
of −55°C to +125°C for the UC1848, −40°C to +85°C for the UC2848, and 0°C to +70°C for the UC3848. Test conditions are: VCC
= 12V, CT = 400pF, CI = 100pF, IOFF = 100µA, CDC = 100nF, Cvs = 100pF, and Ivs = 400µA, TA = TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
0.95
1
20
25
MAX UNITS
Real Time Current Waveform Synthesizer
Ion Amplifier
Offset Voltage
Slew Rate (Note 1)
lib
1.05
V
V/µs
-2
-20
µA
IOFF Current Mirror
Input Voltage
0.95
1
1.05
V
Current Gain
0.9
1
1.1
A/A
60
100
10
mV
-3
µA
Current Error Amplifier
AVOL
Vio
12V ≤ VCC
20V, 0V
VCM
5V
lib
-0.5
Voh
IO = −200µA
Vol
IO = 200µA
Source Current
VO = 1V
GBW Product
f = 200kHz
3
Slew Rate (Note 1)
dB
3.3
V
0.3
0.6
V
1.4
1.6
2.0
5
8
MHz
8
10
V/µs
240
250
mA
Oscillator
Frequency
TA = 25°C
235
Ramp Amplitude
260
kHz
265
kHz
1.5
1.65
1.8
V
73.5
76.5
79.5
%
1100
ns
14
V
Duty Cycle Clamp
Max Duty Cycle
V(DMAX) = 0.75 • VREF
Volt Second Clamp
Max On Time
900
VCC Comparator
Turn-on Threshold
13
Turn-off Threshold
Hysteresis
3
9
10
2.5
3
V
3.5
V
UC1848
UC2848
UC3848
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, all specifications are over the junction temperature range
of −55°C to +125°C for the UC1848, −40°C to +85°C for the UC2848, and 0°C to +70°C for the UC3848. Test conditions are: VCC
= 12V, CT = 400pF, CI = 100pF, IOFF = 100µA, CDC = 100nF, Cvs = 100pF, and Ivs = 400µA, TA = TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
UV Comparator
Turn-on Threshold
RHYSTERESIS
4.1
4.35
4.6
V
Vuv = 4.2V
77
90
103
kΩ
TA = 25°C
4.95
5
5.05
V
0 < IO < 10mA, 12 < VCC < 20
4.93
Reference
VREF
Line Regulation
12 < VCC < 20V
Load Regulation
0 < IO < 10mA
Short Circuit Current
VREF = 0V
4
30
5.07
V
15
mV
3
15
mV
50
70
mA
Output Stage
Rise & Fall Time (Note 1)
Cl = 1nF
20
45
ns
Output Low Saturation
IO = 20mA
0.25
0.4
V
IO = 200mA
1.2
2.2
V
Output High Saturation
IO = -200mA
2.0
3.0
V
UVLO Output Low Saturation
IO = 20mA
0.8
1.2
V
ISTART
VCC = 12V
0.2
0.4
mA
ICC (pre-start)
VCC = 15V, V(UV) = 0
0.5
1
mA
22
26
mA
ICC
ICC (run)
APPLICATION INFORMATION
Under Voltage Lockout
When the UV comparator is low, ICC is low (500µA) and
the output is low.
The Under Voltage Lockout block diagram is shown in
Fig 1. The VCC comparator monitors chip supply voltage.
Hysteretic thresholds are set at 13V and 10V to facilitate
off-line applications. If the VCC comparator is low, ICC is
low (<500µA) and the output is low.
When both the UV and VCC comparators are high, the
internal bias circuitry for the rest of the chip is activated.
The CDC pin (see discussion on Maximum Duty Cycle
Control and Soft Start) and the Output are held low until
VREF exceeds the 4.5V threshold of the VREF comparator. When VREF is good, control of the output driver is
transferred to the PWM circuitry and CDC is allowed to
charge.
The UV comparator monitors input line voltage (VIN). A
pair of resistors divides the input line to UV. Hysteretic input line thresholds are programmed by Rv1 and Rv2. The
thresholds are
VIN(on) = 4.35V • (1 + Rv1/Rv2′) and
VIN(off) = 4.35V • (1 + Rv1/Rv2) where
Rv2′= Rv2||90k.
The resulting hysteresis is
VIN(hys) = 4.35V • Rv1 / 90k.
If any of the three UVLO comparators go low, the UVLO
latch is set, the output is held low, and CDC is discharged. This state will be maintained until all three comparators are high and the CDC pin is fully discharged.
4
UC1848
UC2848
UC3848
APPLICATION INFORMATION (cont.)
UDG-93004
Oscillator Frequency as a Function of CT
Frequency Decrease as a Function of RT
FREQUENCY (kHz)
10000
1000
RT = Open
100
10
10
100
1000
C (pF)
UDG-93006
UDG-93005
5
10000
UC1848
UC2848
UC3848
APPLICATION INFORMATION (cont.)
of the switch. During the off time, switch current drops
abruptly to zero, but the inductor current actually diminishes with a slope dIL/dt = –VO/L. This down slope must
be synthesized in some manner on the primary side to
provide the entire inductor current waveform for the control circuit.
The patented current waveform synthesizer (Fig. 4) consists of a unidirectional voltage follower which forces the
voltage on capacitor CI to follow the on time switch current waveform. A programmable discharge current synthesizes the off time portion of the waveform. ION is the
input to the follower. The discharge current is programmed at IOFF.
The follower has a one volt offset, so that zero current
corresponds to one volt at CI. The best utilization of the
UC3848 is to translate maximum average inductor current to a 4V signal level. Given N and Ns (the turns ratio
of the power and current sense transformers), proper
scaling of IL to V(CI) requires a sense resistor Rs as calculated from:
UDG-93008-1
Rs = 4V Ns N / IL(max).
Oscillator
Restated, the maximum average inductor current will be
limited to:
A capacitor from the CT pin to GND programs oscillator
frequency, as shown in Fig. 2. Frequency is determined
by:
IL(max) = 4V Ns N/Rs.
IOFF and CI need to be chosen so that the ratio of
dV(CI)/dt to dIL/dt is the same during switch off time as
on time. Recommended nominal off current is 100 A.
This requires
F = 1 / (10k CT).
The sawtooth wave shape is generated by a charging
current of 200 A and a discharge current of 1800 A. The
discharge time of the sawtooth is guaranteed dead time
for the output driver. If the maximum duty cycle control is
defeated by connecting DMAX to VREF, the maximum
duty cycle is limited by the oscillator to 90%. If an adjustment is required, an additional trim resistor RT from CT
to Ground can be used to adjust the oscillator frequency.
RT should not be less than 40k . This will allow up to a
22% decrease in frequency.
CI = (100 A N Ns L) / (Rs VO(nom))
where L is the output inductor value and VO(nom) is the
converter regulated output voltage.
There are several methods to program IOFF. If accurate
average current control is required during short circuit operation, IOFF must track output voltage. The method
shown in Fig. 4 derives a voltage proportional to VIN D
(Duty Cycle). (In a buck converter, output voltage is proportional to VIN D.) A resistively loaded diode connection to the bootstrap winding yields a square wave whose
amplitude is proportional to VIN and is duty cycle modulated by the control circuit. Averaging this waveform with
a filter generates a primary side replica of secondary regulated VO. A single pole filter is shown, but in practice a
two or three pole filter provides better transient response.
Filtered voltage is converted by ROFF to a current to the
IOFF pin to control CI down slope.
Inductor Current Waveform Synthesizer
Average current mode control is a very useful technique
to control the value of any current within a switching converter. Input current, output inductor current, switch current, diode current or almost any other current can be
controlled. In order to implement average current mode
control, the value of the current must be explicitly known
at all times. To control output inductor current (IL) in a
buck derived isolated converter, switch current provides
inductor current information, but only during the on time
6
UC1848
UC2848
UC3848
APPLICATION INFORMATION (cont.)
If the system is not sensitive to short circuit requirements,
Figure 5 shows the simplest method of downslope generation: a single resistor (ROFF = 40k) from IOFF to VREF.
The discharge current is then 100µA. The disadvantage
to this approach is that the synthesizer continues to generate a down slope when the switch is off even during
short circuit conditions. Actual inductor down slope is
closer to zero during a short circuit. The penalty is that
the average current is understated by an amount approximately equal to the nominal inductor ripple current. Output short circuit is therefore higher than the designed
maximum output current.
A third method of generating IOFF is to add a second
winding to the output inductor core (Fig. 6). When the
power switch is off and inductor current flows in the free
wheeling diode, the voltage across the inductor is equal
to the output voltage plus the diode drop. This voltage is
then transformed by the second winding to the primary
side of the converter. The advantages to this approach
are its inherent accuracy and bandwidth. Winding the
second coil on the output inductor core while maintaining
the required isolation makes this a more costly solution.
In the example, ROFF = VO / 100µA. The 4 • ROFF resistor is added to compensate the one volt input level of
the IOFF pin. Without this compensation, a minor current
foldback behavior will be observed.
UDG-93009
UDG-93011
UDG-93010
7
UC1848
UC2848
UC3848
APPLICATION INFORMATION (cont.)
Maximum Volt-Second Circuit
Ground Planes
A maximum volt-second product can be programmed by
a resistor (Rvs) from VS to VIN and a capacitor (Cvs)
from VS to ground (Figure 7). VS is discharged while the
switch is off. When the output turns on, VS is allowed to
charge. Since the threshold of the VS comparator is
much less than VIN, the charging profile at Vs will be essentially linear. If VS crosses the 4.0V threshold before
the PWM turns the output off, the VS comparator will turn
the output off for the remainder of the cycle. The maximum volt-second product is
The output driver on the UC3848 is capable of 2A peak
currents. Careful layout is essential for correct operation
of the chip. A ground plane must be employed (Fig. 8). A
unique section of the ground plane must be designated
for high di/dt currents associated with the output stage.
This point is the power ground to which to PGND pin is
connected. Power ground can be separated from the rest
of the ground plane and connected at a single point, although this is not strictly necessary if the high di/dt paths
are well understood and accounted for. VCC should be
bypassed directly to power ground with a good high frequency capacitor. The sources of the power MOSFET
should connect to power ground as should the return
connection for input power to the system and the bulk input capacitor. The output should be clamped with a high
current Schottky diode to both VCC and PGND. Nothing
else should be connected to power ground.
VIN • TON(max) = 4.0V • Rvs • Cvs.
Maximum Duty Cycle And Soft Start
A patented technique is used to accurately program maximum duty cycle. Programming is accomplished by a divider from VREF to DMAX (Fig. 7). The value
programmed is:
VREF should be bypassed directly to the signal portion
of the ground plane with a good high frequency capacitor.
Low esr/esl ceramic 1 F capacitors are recommended
for both VCC and VREF. The capacitors from CT, CDC,
and CI should likewise be connected to the signal ground
plane.
D(max) = Rd1 / (Rd1 + Rd2).
For proper operation, the integrating capacitor, CDC,
should be larger than CDC(min) >T(osc) / 80k, where
T(osc) is the oscillator period. CDC also sets the soft start
time constant, so values of CDC larger than minimum may
be desired. The soft start time constant is approximately:
T(ss) = 20k • CDC.
UDG-93012-1
8
UDG-93013-1
UC1848
UC2848
UC3848
UDG-93014
UDG-93015
9
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
UC1848J
OBSOLETE
CDIP
J
16
TBD
Call TI
UC2848DW
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Call TI
Level-2-260C-1 YEAR
UC2848DWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC2848J
OBSOLETE
CDIP
J
16
TBD
Call TI
UC3848DW
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Call TI
Level-2-260C-1 YEAR
UC3848DWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3848DWTR
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3848DWTRG4
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3848N
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC3848NG4
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
UC3848DWTR
Package Package Pins
Type Drawing
SOIC
DW
16
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
16.4
Pack Materials-Page 1
10.75
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
10.7
2.7
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UC3848DWTR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated