MB2505 THRU MB2510 SINGLE-PHASE GLASS PASSIVATED SILICON BRIDGE RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 25 Amperes d e u n i nt FEATURES * * * * Superior thermal desing 300 amperes surge rating 1/4" universal faston terminal Hole thru for #8 screw o c is D MECHANICAL DATA * Epoxy : Device has UL flammability classification 94V-0 * UL listed the recongnized component director, file #94233 MB-25 DISCONTINUED- "This series is replaced by the MP25 series that meets to the same fit and function parameters. The MP25 series is preferred for PCB assembly.＂ MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. MB-25W For capacitive load, derate current by 20%. MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) RATINGS MB252 MB254 MB256 Maximum Recurrent Peak Reverse Voltage SYMBOL VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC = 55oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range MB2505 MB251 MB258 MB2510 UNITS IO 25.0 Amps IFSM 300 Amps RqJC 4 RqJA 16 T J, TSTG O -55 to + 150 C/W 0 C ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 12.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage NOTES : VF @TA = 25oC @TA = 100oC 1. Suffix "W" for wire type. 2. Typical Thermal Resistance: Heat-sink case mounted. 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. IR MB2505 MB251 MB252 MB254 1.1 5.0 500 MB256 MB258 MB2510 UNITS Volts uAmps 2007-5 AVERAGE FORWARD CURRENT, (A) 30 25 20 15 10 Single Phase Half Wave 60Hz Inductive or Resistive Load 0.375" (9.5mm) Lead Length 5 0 0 50 100 150 INSTANTANEOUS FORWARD CURRENT, (uA) RATING AND CHARACTERISTICS CURVES ( MB2505 THRU MB2510 ) 1000 TA = 100 OC 100 TA = 75 OC 10 TA = 25 OC 1 0.1 0 500 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.2 TYPICAL REVERSE CHARACTERISTICS 10 TJ = 25 OC Pulse width=300mS 1% Duty Cycle 0 40 CASE TEMPERATURE, ( C) 100 1 20 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (A) O 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 300 140 8.3mS Single Half Sine-Wave JEDEC Method 250 200 150 100 50 0 1 2 5 10 20 50 100 INSTANTANEOUS FORWARD VOLTAGE, (V) NUMBER OF CYCLES AT 60Hz FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .452 MAX. (11.5) .480 (12.2) .425 (10.8) 1.181 (30.0) 1.102 (28.0) .673 (17.1) .633 (16.1) AC .732 (18.6) .692 (17.6) AC .582 (14.8) .543 (13.8) MB-25 .452 MAX. (11.5) .042 (1.1) DIA. .080 (2.0) TYP. 1.181 (30.0) 1.102 (28.0) HOLE FOR NO. 8 SCREW 1.181 (30.0) 1.102 (28.0) .673 (17.1) .633 (16.1) .591 MAX. (15.0) 1.181 (30.0) 1.102 (28.0) AC .732 (18.6) .692 (17.6) AC .033x.250 (0.8x6.4) HOLE FOR NO. 8 SCREW .732 (18.6) .692 (17.6) MB-25W .468 (11.9) .429 (10.9) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.