UNISONIC TECHNOLOGIES CO., LTD L6726 LINEAR INTEGRATED CIRCUIT UNIVERSAL SPEECH CIRCUIT DESCRIPTION The UTC L6726 is a mask-programmable, monolithic integrated speech circuits for using in electronic telephones. It is designed for using with a low impedance microphone. Transmitting and receiving gain are regulated with line length. Different regulation for various current feeds can be set by external resistors. Typical current feeds as 48V 2·200Ω, 48V, 2·400Ω, and 36V, 2·500Ω, can be handled. Application dependent parameters such as line balance, side tone level, amplification and frequency response are set by external components. Parameters are set independently which means easy adaptation for various market needs. The UTC L6726 is developed for using with CMOS-type dialer ICs. A separate DTMF input is switched when the circuit is muted, and an adjustable DC supply is provided for feeding an external CMOS device. FEATURES *Minimum number of inexpensive external components, 5 capacitors and 11 resistors. *Mute function for operation with DTMF-generator. *Transmit and receive gain regulation for automatic loop loss compensation. *Extended current and voltage range 5~130mA, down to 2V. *Differential microphone input for good balance to ground. *Balanced receiver output stage. *Short start-up time. *Stabilized DC-supply for low current CMOS dialers and/or electret microphones. *DTMF-input controlled by mute. ORDERING INFORMATION Ordering Number Lead Free L6726L-D18-T L6726L-S18-R L6726L-S18-T Halogen Free L6726G-D18-T L6726G-S18-R L6726G-S18-T www.unisonic.com.tw Copyright © 2012 Unisonic Technologies Co., Ltd Package Packing DIP-18 SOP-18 SOP-18 Tube Tape Reel Tube 1 of 13 QW-R108-015,C L6726 LINEAR INTEGRATED CIRCUIT PIN CONFIGURATION PIN DESCRIPTIONS Pin No. Pin Name 1 +L 2 TO 3 TI 4 +C 5 Mute 6 7 8 9 10 11 12 13 14 15 16 17 18 GR DCS DCO DCC DI MO MI 1 MI 2 -L RI DR RE 1 RE 2 Description Output of the DC-regulator and transmit amplifier. This pin is connected to the line through a polarity guard and diode bridge. Output of the transmit amplifier. This pin is connected through a resistor of 47 to 100Ω to -L, which sets the DC-resistance of the circuit. The output has a low AC output impedance and the signal is used to drive a side tone balancing network. Input of transmit amplifier. Input impedance 17kΩ±20% The positive power supply terminal for most of the circuitry inside the UTC L6726 (about 1mA current consumption).The +C-PIN shall be connected to a decoupling capacitor of 47μF to 150μF When low, speech circuit is muted and the DTMF input is enabled. Maximum voltage (at mute) is 0.3V,current sink requirement of external driver is 50μA Control input for the gain regulation circuitry. The sense input to the DC-supply. The output from the DC-supply. The control output from the DC-supply The input for the DTMF-signal. Input impedance is 25kΩ±20% Output of the microphone amplifier or DTMF-amplifier Input to the microphone amplifier. Input impedance 1.7kΩ±20% The negative power terminal, connected to the line though a polarity guard diode bridge Input of receiver amplifier. Input impedance is approximately 38kΩ±20% The control input for the receiver amplifier driving capability. Receiver amplifier outputs. Output impedance is approximately 3Ω. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT Line Voltage, tP =2s VL 0~22 V Line Current, Continuous IL 0~130 mA Operating Temperature TOPR -40~+70 °C Storage Temperature TSTG -55~+125 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. ELECTRICAL CHARACTERISTICS (TA=25℃ unless otherwise specified) PARAMETER FIG. TEST CONDITIONS Line Voltage 1 IL=15mA IL=100mA Transmitting Gain, Note 1 1 20·10log(V2/V3), 1kHz Transmitting Range Of Regulation Transmitting Frequency Response 1 1 1kHz, RL=0 ~ 900 Ω 200Hz ~ 3.4kHz Receiving Gain, Note 1 1 20·10log (V4/V1), 1kHz Receiving Range Of Regulation Receiving frequency response Microphone Input Impedance Pin12,13 Transmitter Input Impedance Pin 3 1 1 1kHz, RL=0 ~ 900 Ω 200Hz ~ 3.4kHz 1 1kHz, note 3 1 Transmitter Dynamic Output 1 Transmitter Max Output Receiver Output Impedance 1 1 Receiver Dynamic Output (Note 2) 1 Receiver Max Output 2 Transmitter Output Noise 1 Receiver Output Noise 1 1kHz 200Hz~3.4kHz, ≤2% distortion, IL=20~100mA 200 Hz~3.4kHz, IL=0-100mA,V3=0.1V 1kHz, note 3 200Hz~3.4kHz ≤2% distortion, IL=20~100mA Measured with line rectifier 200 Hz~3.4kHz, IL=0~100mA, V1=0~50V PSOF-weighting, Rel1 VRMS, RL=0 A-weighting, Rel 1VRMS, with cable 0~5km, φ=0.5mm, 0~3km, φ=0.3mm Mute Input Voltage at Mute (Active Low) 1 DC-Supply Voltage 1 RL=0Ω RL=400Ω RL=900Ω~2.2kΩ RL=0Ω RL=400Ω RL=900Ω~2.2kΩ TYP 3.7 13 43 45.5 48 5 -16.5 -14 -11.5 5 MAX UNIT 4.1 V 15 45 dB 47.5 50 7 dB 1 dB -14.5 -12 dB -9.5 7 dB 1 dB 1.7(//2.7) kΩ 17 kΩ 1.5 Vp 3 3(+310) Vp Ω 0.5 Vp 0.9 Vp -75 dBPSOF -85 dBA 0.3 IL=10~100mA, IDC=0mA IL=10~100mA, IDC=2mA DC-Supply Current, Pin8 1 Dc-Output Pin8 Input Leakage 3 VDC=2.35V Current (No Supply) DTMF Transmitting Gain 1 VM=0.3V Notes: 1. Adjustable to both higher and lower values with external components. 2. The dynamic output can be doubled, see applications information. 3. External resistor in the test set up. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 3.3 11 41 43.5 46 3 -1 -18.5 -16 -13.5 3 -1 2.35 2.2 V 2 mA 0.1 24.5 V 26.5 μA 28.5 dB 3 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT FUNCTIONAL DIAGRAM 1 DTMF input UTC L6726 10 17 AD AR AT 12 Telephone Line 18 AM 13 DC 8 9 7 5 11 3 2 15 16 6 14 4 DC output for external 3 CMOS device 1 Mute (active low) 5 2 4 1.Impedance to line and radio interference suppression. 2.Transmit gain and frequency response network. 3.Receive gain and frequency response network. 4.Side tone balance network. 5.DC-supply components. MUTE RL=0~4KΩ 0 Ω when artificail line is used 5H+5H RLoad =400Ω+400Ω E=48.5V +LINE DTMF 600Ω V2 + ARTIFICAIAL LINE + C1 1μF VM IL IDC VL VDC V3 UTC 6726 with external component see fig 3 REC V1 ZMIC=350 Ω MIC V4 ZRec=350 Ω -LINE C1= 1μF when artificial line is used 470μF when not used Fig. 1 Test setup without rectifier bridge MUTE VM RL=0~4KΩ 5H+5H RLoad =400Ω+400Ω + E=50V C1 1μF V2 Uz=(15 ~16)V IL +LINE + DTMF 600Ω VL IDC V3 UTC 6726 with external component see fig 3 REC V1 ZMIC=350 Ω MIC V4 ZRec=350 Ω VDC -LINE Fig. 2 Test setup with rectifier bridge UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT FUNCTIONAL DIAGRAM(Cont.) +Line 1 DTMF input C8 10 220nF DC 8 9 7 CMOS device 1 8 AM 13 DC supply OUT 5 Sense input Control output R4 18k 11 3 C3 100nF MUTE R5 22k + 47μF R14 310Ω AR AT 12 MIC R16 350Ω 27k 1 7 UTC 6726 AD R6 75 Ω C7 15 14 6 2 R7 910 Ω C4 47nF R11 560Ω 3kΩ R8 R9 11k Note : * Not used in test setup R13 C5 11k REC 350 Ω 14 4 R10 82k 910 Ω R3 R1 * R15 R2 * 10 Ω 47μF + C1 C2 15nF -Line 100nF Fig. 3 Circuit with external components for test setup. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT FUNCTIONAL DESCRIPTION The gain of the transmitting and receiving amplifiers are continuously and euqually changed with the line length. The starting point for the gain regulation is externally set .The gain regulation can be cut-off externally, see table under gain regulation below. The outputs of the transmitting and receiving amplifiers have internals limitations of the output amplitudes. The circuit includes a temperature independent voltage reference used for regulation of the DC line voltage and for the transmitting and receiving gain regulation. The DC voltage is very fast settled to its final value with a minimum of overshoot. The circuit uses a minimum of external components. In a normal practical case only 5 external capacitors of which only one is an electrolytic/tantalum filter capacitor .The other capacitor are needed as radio interference suppression capacitor over the line, one capacitor in the side-tone balancing network and one capacitor for low frequency cut-off in each of the transmitting and receiving amplifiers. The frequency response is except for that, flat for both amplifiers. The circuit will with external components get a very good return loss behavior both against purely resistive lines as for instance 600 Ω and against complex networks as 900 Ω in parallel with 30nF. To get a good CMRR the microphone input is balanced. It is possible to add a push-button controlled cut-off of the transmitting amplifier to the circuit without any disturbance of the other circuit functions A mute input is included in the circuit. It gives: 1. Cut-off the microphone amplifier. 2. Reduced gain in the receiving amplifier. 3. Connection of the DTMF input. The receiver amplifier is equipped with a high impedance input stage. This gives a less expensive RC-network on the input. Only resistive elements are used to set the receiving gain. A push-pull power stage in the receiving amplifier gives a high output swing. To get the extended low current and voltage range two resistors have to be connected from microphone input to ground. The side-tone balanced can be set by a RC-network without influence on other parameters. An inexpensive solution requires only one capacitor while more capacitors can give better performance. In fig.4①②③ and ④ are RC-links with the following functions: 1. For radio interference suppression and to give the correct return loss behavior. 2. To set the gain and frequency response for transmitting. 3. To set the gain and frequency response for receiving. 4. To set the side-tone level A stabilized DC output, with a pre-set output voltage of 2.35V, is provided to facilitate interfacing to external COMS dialer ICs. The voltage is adjustable with two resistors, as indicated in fig.5. The output requires some filtering to avoid distortion on the telephone line. Note that a high current consumption of the external device will alters the DC characteristics of the speech circuit. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT FUNCTIONAL DESCRIPTION(Cont.) 1.2V 1 +Line 8 0~470Ω + - VDC1 0~470Ω 9 15kΩ 15kΩ 7 14 RDC1 RDC2 + VDC2 + 4.7~47μF Fig. 5 DC regulator for external CMOS devices UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION Refer to fig. 6 Gain regulation (R1, R2): These resistors set the starting point for the gain-and side tone regulation. Input impedance pin 6 is about 5.5 kΩ±20%. Below are some typical values for R1 and R2, for some different supplies from telephone stations. Battery feed R1 R2 R6 No regulation Set for short line gain. 22kΩ 47~100Ω All feedings Regulation: 47Ω ∞ ∞ 48V, 2·200Ω 75Ω ∞ ∞ 48V, 2·400Ω 100Ω 180kΩ 36V, 2·500Ω Impedance to line (R3, C1, C2): C1 in series with R3 and those in parallel with C2 give the impedance to the line from the set. C2 must normally be there for the interference too. The network is optimized with regard to the return loss. The time constant R3, C1 cannot be allowed to be too small. If the time constant is to small, distortion at low frequencies may be generated. If R3 is changed this will change the DC-characteristic too, which set by the voltage at pin 4. The input current at pin 4 is about 1mA Microphone selection (M1, R16): The microphone can be either dynamic, magnetic or electrets. See fig. 12, 14 and 15. The input impedance between pin 12 and 13 is about 1.7kΩ with typical variation ±20% Transmitting gain and frequency response (R4, R5, C3, C4): The network gives the amplification and frequency response for the transmitter. R5 is used when a greater reduction of the gain is wanted. Input impedance at pin 3 is about 17 kΩ with typical variation ±20%.The sum of the resistors R4 and R5 must not be less than 35 kΩ because of DC-current to ground. Below is some simple variations of this network. (See fig. 7). DC-characteristics (R6): Sets the DC-characteristic and take care of some of the supplied power. The resistor have also function with the protection of the circuit, the transmitter, the gain regulation and side tone. Common values are 47 Ω to 100 Ω. Side tone level, receiving gain and frequency response.(R7,R8,R9,R10,R11,C5): The network sets the side tone balance. The network in the application is one of many possibilities. R10 and R11 balance together the signals that go two different ways from the transmitter output stage one from pin1 and the other from pin2. The balance network consist of R8, R9 and C5. The example is not optimized to any specified line, it is only given to show the principle. Fig8, 9 and 10 are examples of balance networks. Fig.10 is especially suited for lines with high current supply. R12, R13, C6, (R10, R11): The networks gives the gain and frequency response for the receiver. Input impedance at pin 15 is about 38 kΩ with a typical variation of ±20%.For different possibilities for the design of the network, see the network for the transmitter (R4, R5, C3) REC, R14: R14 generates the output impedance to the magnetic earphone (fig.11). If a dynamic earphone is used it should be placed between pin 17 and 18.See fig. 16. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 8 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION(Cont.) R15: This resistor is used to set the driving capability of the receiver output amplifier. Common values are 0 Ω to 50 Ω. Setting it for low driving capability results in function at lower line current. Breaking up pin 16 will give lower power consumption and total mute of the receiver when muting the circuit. Disconnecting pin 15 will of cause also give total receiver mute. D1, D2, D3, D4, D5: Rectifier bridge and over voltage protector. The zener voltage at D5 should be as low as possible. Common values are between 12V~16V. RDC1, RDC2: Refer to fig. 5 The pre-set output voltage of 2.35V can easily, if needed, be changed to another value by applying one or two resistor(RDC1,RDC2) in parallel with the internal resistors (each 15kΩ+/-20%).It is possible to get a rather high voltage and current from the DC-supply as long as the high current and voltage is available from the line. The DC voltage has to be filtered by a capacitor and this can, at high DC-voltage and low line current, interfere with the signal on the line and cause distortion. You can minimize the interference, with a resistor in series with the filter capacitor. The DC voltage will, of course, be more dependent of the DC-supply current. The DC-output pin has a very low input leak current, to allow stand-by feeding of the dialer. It is also possible to use pin 9 to feed microphones etc. that do not need stand-by feeding, without interfering with the stand-by feeding on pin 8. Note that a high current consumption by the external device will alter the DC characteristics of the speech circuit UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 9 of 13 QW-R108-015, C www.unisonic.com.tw 9 # 8 0 7 * UNISONIC TECHNOLOGIES CO., LTD 13 12 10 47μF 220nF Note : * Not used in test setup GND MUTE out DC DTMF dialler (CMOS type) DTMF Output 6 5 4 3 2 1 22k 18k 5 11 75Ω 100nF 3 AT 6.2k 15 16 6 AR 11k 100 nF 11k 10Ω 560Ω 910Ω 2 UTC L6726 Fig. 6 Typical tong dialling telephone Sense input Control output 8 9 7 DC AM AD 1 ∞ ∞ 14 * * 4 82k 18 17 47μF 910Ω 15nF 10Ω Telephone Line UZ=12V KEYPAD L6726 LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION(Cont.) QW-R108-015, C 10 of 13 L6726 LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION(Cont.) DESIGN PROCEDURE: 1. Circuit impedance to the line. 2. DC-characteristic 3. Gain regulation. 4. Transmitter gain and frequency response. 5. Receiver gain and frequency response. 6. Side-tone. 7. Components to suppress radio interference, specially the wires up to the handset. Others: The circuit can be placed either in the telephone or in the handset. Cut off the transmitter can be done at F1 without interference of other functions of the circuit. When using the extended low current and low voltage range (5mA, 2V), two resistors have to be connected from the microphone inputs to ground as shown in fig. 13. 11 11 3 3 2 15 RA RA CA RB CB 11 RA RB R6 11 3 3 2 RA CA RA 3 11 RA RB 3 RA RB 3 R6 CA CB R10 +Line CB 11 CA R11 RB RA RA 15 2 CA RB 11 CA RC 3 CA CA R10 +Line R11 RB RB CB RB R6 11 15 RA CA CB R10 +Line R11 CA RA RB RC CA Fig. 8 Examples of network "4" CB Fig. 7 Examples of network "2" UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 11 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION(Cont.) +Line R10 R12 +Line 2 C6 Zbal 15 2 R11 RA R6 C6 15 R12 RB R6 C Low impedance network. Rc * To get flat response for receiving Fig. 10 Sidetone network especially suited for applicatons with a high line current,when R6 has a low value Fig. 9 Typical sidetone network 4 R14 17 200Ω 200Ω 1μF 1μF 12 13 18 14 Fig.11 Magnetic reciever connection Fig. 12 Electret microphone with FET buffer 12 12 MIC 13 50k 11 AM 50k -Line Fig. 13 Additional components for extended low current/voltage oeration UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 13 Fig. 14 Connection of a magnetic microphone 12 of 13 QW-R108-015, C L6726 LINEAR INTEGRATED CIRCUIT UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 13 of 13 QW-R108-015, C