54ACTQ32QML 54ACTQ32QML Quiet Series Quad 2-Input OR Gate Literature Number: SNOSAM1 54ACTQ32QML Quiet Series Quad 2-Input OR Gate General Description Features The ’ACTQ32 contains four, 2-input OR gates and utilizes NSC Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet Series™ features GTO™ output control and undershoot corrector in addition to a split ground bus for superior ACMOS performance. Radiation features 54ACTQ32 guaranteed to 100k rd(Si) ICC reduced by 50% Minimum 4KV ESD protection Guaranteed simultaneous switching noise level and dynamic threshold performance n Improved latch-up immunity n Outputs source/sink 24 mA n ACTQ32 has TTL-compatible inputs n n n n Ordering Information NS Part Number JAN Part Number NS Package Number Package Description 54ACTQ32JRQMLV 5962R8973601VCA 100k rd(Si) J14A 14LD CERDIP 54ACTQ32WRQMLV 5962R8973601VDA 100k rd(Si) W14B 14LD CERPACK Logic Symbol IEEE/IEC 20139401 GTO™ is a trademark of National Semiconductor Corporation. FACT™ and FACT Quiet Series™ are trademarks of Fairchild Semiconductor Corporation. © 2005 National Semiconductor Corporation DS201394 www.national.com 54ACTQ32QML Quiet Series Quad 2-Input OR Gate December 2005 54ACTQ32QML Connection Diagram Pin Assignment for DIP and Flatpak 20139403 Pin Names Description An, Bn Inputs On Outputs Capacitance Symbol CI CPD Max Units Input Capacitance Parameter 10.0 pF VCC = Open Power Dissipation 72.0 pF VCC = 5.0V Capacitance www.national.com 2 Conditions 54ACTQ32QML Absolute Maximum Ratings (Note 1) Supply Voltage (VCC) −0.5V to +7.0V DC Input Diode Current (IIK) VI = −0.5V −20 mA VI = VCC + 0.5V +20 mA DC Input Voltage (VI) −0.5V to VCC + 0.5V DC Output Diode Current (IOK) VO = −0.5V −20 mA VO = VCC + 0.5V +20 mA DC Output Voltage (VO) −0.5V to VCC + 0.5V ± 50 mA ± 50 mA DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGnd) Thermal Resistance, Junction to Case (θJC) See Mil-Std-1835 Storage Temperature (TStg) −65˚C ≤ TA ≤ +150˚C Junction Temperature (TJ) 175˚C Maximum Power Dissipation (PD) 500mW Lead Temperature (soldering, 10 seconds) 300˚C Recommended Operating Conditions Supply Voltage (VCC) 4.5V to 5.5V Input Voltage (VI) 0V to VCC Output Voltage (VO) 0V to VCC −55˚C ≤ TA ≤ +125˚C Operating Temperature (TA) Minimum Input Edge Rate (∆V/∆t) VI from 0.8V to 2.0V VCC @ 4.5V, 5.5V 125 mV/ns Maximum High Level Output Current (IOH) −24mA Maximum Low Level Output Current (IOL) +24mA Radiation Features 54ACTQ32JRQMLV 100 krads (Si) 54ACTQ32WRQMLV 100 krads (Si) Quality Conformance Inspection Mil-Std-883, Method 5005 - Group A Subgroup Description 1 Static tests at Temp ˚C 25 2 Static tests at 125 3 Static tests at -55 4 Dynamic tests at 25 5 Dynamic tests at 125 6 Dynamic tests at -55 7 Functional tests at 25 8A Functional tests at 125 8B Functional tests at -55 9 Switching tests at 25 10 Switching tests at 125 11 Switching tests at -55 3 www.national.com 54ACTQ32QML 54ACTQ32–QMLV RH Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VCC = 4.5V to 5.5V, Temperature range −55˚C to 125˚C Symbol IIH IIL VOL Parameter High Level Input Current Low Level Input Current Low Level Output Voltage Max Units Subgroups (Note 2), (Note 3) 0.1 µA 1 (Note 2), (Note 3) 1.0 µA 2, 3 (Note 2), (Note 3) -0.1 µA 1 (Note 2), (Note 3) -1.0 µA 2, 3 VCC = 4.5V, VIH = 2.0V, VIL = 0.8V, IOL = 50.0µA (Note 2), (Note 3) 0.1 V 1, 2, 3 VCC = 5.5V, VIH = 2.0V, VIL = 0.8V, IOL = 50.0µA (Note 2), (Note 3) 0.1 V 1, 2, 3 VCC = 4.5V, VIH = 2.0V, VIL = 0.8V, IOL = 24.0mA (Note 2), (Note 3) 0.36 V 1 (Note 2), (Note 3) 0.5 V 2, 3 (Note 2), (Note 3) 0.36 V 1 (Note 2), (Note 3) 0.5 V 2, 3 VCC = 5.5V, VIH = 5.5V, VIL = 0.0V, IOL = 50.0mA (Note 2), (Note 3), (Note 6) 1.65 V 1, 2, 3 VCC = 4.5V, VIH = 2.0V, VIL = 0.8V, IOL = -50.0µA (Note 2), (Note 3) 4.40 V 1, 2, 3 VCC = 5.5V, VIH = 2.0V, VIL = 0.8V, IOL = -50.0µA (Note 2), (Note 3) 5.40 V 1, 2, 3 VCC = 4.5V, VIH = 2.0V, VIL = 0.8V, IOL = -24.0mA (Note 2), (Note 3) 3.86 V 1 (Note 2), (Note 3) 3.70 V 2, 3 (Note 2), (Note 3) 4.86 V 1 (Note 2), (Note 3) 4.70 V 2, 3 VCC = 5.5V, VIH = 2.0V, VIL = 0.8V, IOL = -50.0mA (Note 2), (Note 3), (Note 6) 3.85 V 1, 2, 3 VCC = 5.5V, VIH = 5.5V (Note 2), (Note 3) 100 nA 1 (Note 2), (Note 3) 40 µA 2, 3 (Note 2), (Note 3) 100 nA 1 (Note 2), (Note 3) 40 µA 2, 3 Conditions VCC = 5.5V, VIH = 5.5V VCC = 5.5V, VIL = 0.0V VCC = 5.5V, VIH = 2.0V, VIL = 0.8V, IOL = 24.0mA VIOL VOH Dynamic Output Current LOW High Level Output Voltage VCC = 5.5V, VIH = 2.0V, VIL = 0.8V, IOL = -24.0mA VIOH ICCH ICCL Dynamic Output Current HIGH Supply Current Supply Current www.national.com VCC = 5.5V, VIH = 0.0V 4 Notes Min (Continued) DC Parameters (Continued) The following conditions apply, unless otherwise specified. DC: VCC = 4.5V to 5.5V, Temperature range −55˚C to 125˚C Symbol Parameter Supply Current Functional ICCF Supply Current ICCT Conditions VCC = 5.5V, VIH = 0.0V VCC = 5.5V, VIH = 3.4V Max Units Subgroups (Note 2), (Note 3) 100 nA 1 (Note 2), (Note 3) 40 µA 2, 3 (Note 2), (Note 3) 1.0 mA 1 (Note 2), (Note 3) 1.6 mA 2, 3 Notes Min VIKL VCC = 4.5V, IKL = -18mA (Note 2), (Note 3) -1.2 V 1, 2, 3 VIKH VCC = 4.5V, IKH = 18mA (Note 2), (Note 3) 5.7 V 1, 2, 3 0.8 V 4 V 4 VILD Maximum Low Level Dynamic Input Voltage VCC = 5.0V, Load 50pF / 500Ω (Note 7), (Note 10) VIHD Minimum High Level Dynamic Input Voltage VCC = 5.0V, Load 50pF / 500Ω (Note 7), (Note 10) VOLP Quiet Output Maximum Dynamic VOL VCC = 5.0V, Load 50pF / 500Ω (Note 7), (Note 9) 1.5 V 4 VOLV Quiet Output Minimum Dynamic VOL VCC = 5.0V, Load 50pF / 500Ω (Note 7), (Note 9) -1.2 V 4 2.2 AC Parameters The following conditions apply, unless otherwise specified. AC: CL = 50pF, RL = 500Ω, tRise = 3.0nS, tFall = 3.0nS Symbol tPLH tPHL Parameter Propagation Delay Propagation Delay Conditions VCC = 4.5V VCC = 4.5V Notes Min Max Units Subgroups (Note 4), (Note 5), (Note 8) 1.5 7.0 ns 9 (Note 4), (Note 5), (Note 8) 1.5 7.5 ns 10, 11 (Note 4), (Note 5), (Note 8) 1.5 7.0 ns 9 (Note 4), (Note 5), (Note 8) 1.5 7.5 ns 10, 11 tOSLH Output to Output Skew VCC = 4.5V (Note 7) 1.0 ns 9, 10, 11 tOSHL Output to Output Skew VCC = 4.5V (Note 7) 1.0 ns 9, 10, 11 5 www.national.com 54ACTQ32QML 54ACTQ32–QMLV RH Electrical Characteristics 54ACTQ32QML 54ACTQ32–QMLV RH Electrical Characteristics (Continued) Delta Parameters The following conditions apply, unless otherwise specified. Burn-in and operating life test, Delta parameters (+25˚C) Symbol Parameter Conditions Notes Min Max Units Subgroups ICCH Quiescent supply current (Note 11), (Note 12) ± 100 nA 1 ICCL Quiescent supply current (Note 11), (Note 12) ± 100 nA 1 Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT™ circuits outside databook specifications. Note 2: Screen tested 100% on each device @ +25˚C & +125˚C temperature, Subgroup 1, 2, 7 & 8. Note 3: Sample tested (TM5005, Table 1) on each manufacturing lot @ +25˚C, +125˚C, & −55˚C, Subgroups A1, 2, 3, 7, & 8 Note 4: Screen tested 100% on each device @ +25˚C, only. Subgroup A9. Note 5: Sample tested (TM5005, Table 1) on each manufacturing lot @ +25˚C, +125˚C, & −55˚C temperature, Subgroups A9, 10 & 11 Note 6: Transmission line driving test, guardbanded limits set for +25˚C, 2mS duration maximum Note 7: Guaranteed but not tested. Design characterization data Note 8: +25˚C, & +125˚C minimum limits guaranteed for 5.5V by guardbanding 4.5V minimum limits. Note 9: Maximum number of outputs defined as (n) switching. Data inputs are driven 0V to 3V. One output @ VOL Note 10: Maximum number of data inputs (n) switching. (n-1) inputs switching 0V to 3V. Input-Under-Test switching 3V to threshold (VILD, 0V to threshold VIHD, ƒ = 1MHz Note 11: These parameters shall be recorded before and after the required burn-in and life tests to determine the delta limits. Note 12: This limit may not be production tested. www.national.com 6 Date Released 12/14/05 Revision A Section New Release, Corporate format. Additions made in conversion: Radiation Features, Delta parameter table in electricals and Notes 11 & 12. 7 Originator Changes L. Lytle 1 MDS datasheet converted into one Corp. datasheet format. Additions made in conversion: Radiation Features, pg 3, Delta parameter table in electricals and Notes 11 & 12 , pg 6 to reflect SMD. MV54ACTQ32–X Rev 1A0 will be archived. www.national.com 54ACTQ32QML Revision History Section 54ACTQ32QML Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Ceramic Dual-In-Line Package (J) NS Package Number J14A www.national.com 8 54ACTQ32QML Quiet Series Quad 2-Input OR Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Ceramic Flatpak (W) NS Package Number W14B National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated