TI LM119HRQMLV

LM119QML
LM119QML High Speed Dual Comparator
Literature Number: SNOSAN3A
LM119QML
High Speed Dual Comparator
General Description
Features
The LM119 is a precision high speed dual comparator fabricated on a single monolithic chip. It is designed to operate
over a wide range of supply voltages down to a single 5V logic
supply and ground. Further, it has higher gain and lower input
currents than devices like the LM710. The uncommitted collector of the output stage makes the LM119 compatible with
RTL, DTL and TTL as well as capable of driving lamps and
relays at currents up to 25 mA.
Although designed primarily for applications requiring operation from digital logic supplies, the LM119 is fully specified for
power supplies up to ±15V. It features faster response than
the LM111 at the expense of higher power dissipation. However, the high speed, wide operating voltage range and low
package count make the LM119 much more versatile than
older devices like the LM711.
■ Available with radiation guaranteed
■
■
■
■
■
■
■
100 krad(Si)
— High Dose Rate
100 krad(Si)
— ELDRS Free
Two independent comparators
Operates from a single 5V supply
Typically 80 ns response time at ±15V
Minimum fan-out of 2 each side
Maximum input current of 1 μA over temperature
Inputs and outputs can be isolated from system ground
High common mode slew rate
Ordering Information
NS Part Number
SMD Part Number
LM119E/883
LM119E-SMD
86014012A
NS Package Number
Package Description
E20A
20LD LCC
E20A
20LD LCC
H10C
10LD T0-100 Metal Can
8601401IA
H10C
10LD T0-100 Metal Can
LM119H-QMLV
5962-9679801VIA
H10C
10LD T0-100 Metal Can
LM119HRQMLV
HIGH DOSE RATE (Note 13)
5962R9679801VIA
100 krad(Si)
H10C
10LD T0-100 Metal Can
LM119HRLQMLV
ELDRS FREE (Note 14)
5962R9679802VIA
100 krad(Si)
H10C
10LD T0-100 Metal Can
LM119H/883
LM119H-SMD
LM119J/883
J14A
14LD CERDIP
8601401CA
J14A
14LD CERDIP
LM119J-QMLV
5962-9679801VCA
J14A
14LD CERDIP
LM119JRQMLV
HIGH DOSE RATE (Note 13)
5962R9679801VCA
100 krad(Si)
J14A
14LD CERDIP
LM119JRLQMLV
ELDRS FREE (Note 14)
5962R9679802VCA
100 krad(Si)
J14A
14LD CERDIP
W10A
10LD CERPAK
LM119J-SMD
LM119W/883
LM119W-SMD
8601401HA
W10A
10LD CERPAK
LM119W-QMLV
5962-9679801VHA
W10A
10LD CERPAK
LM119WRQMLV
HIGH DOSE RATE (Note 13)
5962R9679801VHA
100 krad(Si)
W10A
10LD CERPAK
LM119WRLQMLV
ELDRS FREE (Note 14)
5962R9679802VHA
100 krad(Si)
W10A
10LD CERPAK
LM119WG/883
WG10A
10LD Ceramic SOIC
LM119WG-QMLV
5962-9679801VXA
WG10A
10LD Ceramic SOIC
LM119WGRQMLV
HIGH DOSE RATE (Note 14)
5962R9679801VXA
100 krad(Si)
WG10A
10LD Ceramic SOIC
© 2009 National Semiconductor Corporation
201437
www.national.com
LM119QML High Speed Dual Comparator
January 13, 2009
LM119QML
NS Part Number
SMD Part Number
NS Package Number
LM119WGRLQMLV
ELDRS FREE (Note 14)
5962R9679802VXA
100 krad(Si)
WG10A
LM119 MDE
ELDRS FREE DIE
(Notes 1, 14)
5962R9679802V9A
100 krad(Si)
LM119 MDR
HIGH DOSE RATE DIE
(Notes 1, 13)
5962R9679801V9A
100 krad(Si)
Package Description
10LD Ceramic SOIC
Note 1: FOR ADDITIONAL DIE INFORMATION, PLEASE VISIT THE HI REL WEB SITE AT: www.national.com/analog/space/level_die
Connection Diagrams
Dual-In-Line Package
Leadless Chip Carrier
20143704
Top View
See NS Package Number J14A
20143708
Top View
See NS Package Number E20A
Metal Can Package
20143709
See NS Package Number W10A, WG10A
20143707
Case is connected to pin 5 (V−)
Top View
See NS Package Number H10C
www.national.com
2
LM119QML
Schematic Diagram
20143701
*Do not operate the LM119 with more than 16V between GND and V+
3
www.national.com
LM119QML
Absolute Maximum Ratings (Note 2)
Total Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Ground to Positive Supply Voltage
Differential Input Voltage
Input Voltage (Note 4)
Power Dissipation (Note 3)
Output Short Circuit Duration
Storage Temperature Range
36V
36V
25V
18V
±5V
±15V
500 mW
10 sec
−65°C ≤ TA ≤ 150°C
−55°C ≤ TA ≤ 125°C
150°C
260°C
Operating Ambient Temperature Range
Maximum Junction Temperature (TJ)
Lead Temperature (Soldering, 10 sec.)
Thermal Resistance
θJA
E Package (Still Air)
E Package (500LF/Min Air flow)
H Package (Still Air)
H Package (500LF/Min Air flow)
J Package (Still Air)
J Package (500LF/Min Air flow)
W Package (Still Air)
W Package (500LF/Min Air flow)
WG Package (Still Air)
WG Package (500LF/Min Air flow)
89°C/W
63°C/W
162°C/W
88°C/W
94°C/W
52°C/W
215°C/W
132°C/W
215°C/W
132°C/W
θJC
E Package
H Package
J Package
W Package
WG Package
Package Weight
E Package
H Package
J Package
W Package
WG Package
ESD rating (Note 5)
www.national.com
5°C/W
31°C/W
11°C/W
13°C/W
13°C/W
TBD
TBD
TBD
TBD
225mg
800V
4
Mil-Std-883, Method 5005 - Group A
Subgroup
Description
Temp °C
1
Static tests at
25
2
Static tests at
125
3
Static tests at
-55
4
Dynamic tests at
25
5
Dynamic tests at
125
6
Dynamic tests at
-55
7
Functional tests at
25
8A
Functional tests at
125
8B
Functional tests at
-55
9
Switching tests at
25
10
Switching tests at
125
11
Switching tests at
-55
12
Settling time at
25
13
Settling time at
125
14
Settling time at
-55
5
www.national.com
LM119QML
Quality Conformance Inspection
LM119QML
LM119/883 Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
+ICC
Parameter
Positive Supply Current
Conditions
ILeak
IIB
Negative Supply Current
Output Leakage Current
Input Bias Current
Notes
Min
±VCC = ±15V, VO = Low
V+
-ICC
VCM = 0V
= 5.6V thru 1.4KΩ
±VCC = ±15V, VO = Low
-4.2
V+
-4.5
= 5.6V thru 1.4KΩ
+V
CC = 15V, VCC = -1V,
VGnd = 0V, VO = 35V,
VI = 5mV
Input Offset Current
2
mA
1
mA
2
1.8
µA
1
9.5
µA
2
3
1
0.475
µA
1
.95
µA
2, 3
-3.8
3.8
mV
1
VCM = 1V, RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
+V
-3.8
3.8
mV
1
VCM = 3V, RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
±VCC = ±15V, VCM = 12V,
-3.8
3.8
mV
1
RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
±VCC = ±15V, VCM = -12V,
-3.8
3.8
mV
1
-6.8
6.8
mV
2, 3
-75
75
nA
1
-100
100
nA
2, 3
+V
CC
CC
CC
= 5V, −VCC = 0V,
= 5V, −VCC = 0V,
+V
CC
CC
= 5V, −VCC = 0V, VCM = 1V
= 5V, −VCC = 0V, VCM = 3V
-75
75
nA
1
-100
100
nA
2, 3
-75
75
nA
1
-100
100
nA
2, 3
-75
75
nA
1
-100
100
nA
2, 3
1.5
V
1
±VCC = ±15V, IO = 25mA,
VI = -5mV
−
CC = 5V, VCC = 0V,
IO= 4.0mA
(Note 12)
0.4
V
1, 2
(Note 12)
0.6
V
3
±VCC = ±15V, Delta VO = 12V,
(Note 9),
(Note 10)
10.5
K
4
(Note 9),
(Note 10)
10
K
5, 6
(Note 9),
(Note 11)
8.0
K
4
(Note 9),
(Note 11)
5.0
K
5
(Note 9),
(Note 11)
5.8
K
6
RL = 1.4KΩ
+V
CC
= 5V, −VCC = 0V,
Delta VO = 4.5V, RL = 1.4KΩ
www.national.com
mA
2, 3
+V
Voltage Gain
11.5
µA
±VCC = ±15V, VCM = -12V
AV
1
0.95
±VCC = ±15V, VCM = 12V
Output Saturation Voltage
mA
µA
+V
VSat
11
µA
RS ≤ 5KΩ
IIO
Subgroups
10.0
= 5V, −VCC = 0V,
VCM = 1.5V
Input Offset Voltage
Units
0.475
±VCC = ±15V
+V
VIO
Max
6
LM119QML
LM119-SMD Electrical Characteristics
SMD 8601401
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
+ICC
Parameter
Positive Supply Current
Conditions
ILeak
IIB
Negative Supply Current
Output Leakage Current
Input Bias Current
Notes
Min
±VCC = ±15V, VO = Low
V+
-ICC
VCM = 0V
= 5.6V thru 1.4KΩ
Input Offset Voltage
1
-4.5
mA
2
-6.0
mA
3
= 5.6V thru 1.4KΩ
+V
CC = 15V, VCC = -1V,
VGnd = 0V, VO = 35V
(Note 6)
1.8
µA
1
(Note 6)
10
µA
2, 3
0.475
µA
1
0.95
µA
2, 3
0.475
µA
1
2, 3
±VCC = ±15V
+V
CC
= 5V
+V
CC = 5V, VCM = 1V, RS ≤ 5KΩ
(Note 7)
CC
= 5V, VCM = 3V,
.95
µA
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
-3.8
3.8
mV
1
RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
±VCC = ±15V, VCM = -12V,
-3.8
3.8
mV
1
-6.8
6.8
mV
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
+V
CC
= 5V, VCM = 1V
+V
CC = 5V, VCM = 3V
±VCC = ±15V, VCM = -12V
Output Saturation Voltage
-75
75
nA
1
-100
100
nA
2, 3
-75
75
nA
1
-100
100
nA
2, 3
CC = 5V
(Note 7),
(Note 8)
1.0
3.0
V
1, 2, 3
±VCC = ±15V
(Note 8)
-12
12
V
1, 2, 3
±VCC = ±15V, IO = 25mA,
(Note 6)
1.5
V
1, 2, 3
0.4
V
1, 2
0.6
V
3
10.5
K
4
+V
VI ≤ -5mV
+V
CC
= 3.5V, -VCC = -1V,
VI ≤ -6mV, IO ≤ 3.2mA
AV
Voltage Gain
±VCC = ±15V, Delta VO = 12V,
Common Mode Rejection Ratio
(Note 9)
RL = 1.4KΩ
(Note 9)
10
K
5, 6
+V
(Note 7),
(Note 9)
8.0
K
4
(Note 7),
(Note 9)
5.0
K
5
(Note 7),
(Note 9)
5.8
K
6
80
dB
4
CC = 5V, VCC = 0V,
Delta VO = 4.5V, RL = 1.4KΩ
CMRR
11.5
V+
±VCC = ±15V, VCM = 12V
VSat
1
2, 3
RS ≤ 5KΩ
Input Voltage Range
mA
mA
±VCC = ±15V, VCM = 12V,
VI
11
mA
RS ≤ 5KΩ
Input Offset Current
Subgroups
-4.2
+V
IIO
Units
±VCC = ±15V, VO = Low
(Note 7)
VIO
Max
±VCC = ±15V, VCM = ±12V
7
www.national.com
LM119QML
LM119 Electrical Characteristics
SMD 5962-9679801, HIGH DOSE RATE
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
+ICC
Parameter
Positive Supply Current
Conditions
ILeak
IIB
Negative Supply Current
Output Leakage Current
Input Bias Current
Notes
Min
±VCC = ±15V, VO = Low
V+
-ICC
VCM = 0V
= 5.6V thru 1.4KΩ
Input Offset Voltage
1
-4.5
mA
2
-6.0
mA
3
= 5.6V thru 1.4KΩ
+V
CC = 15V, VCC = -1V,
VGnd = 0V, VO = 35V
(Note 6)
1.8
µA
1
(Note 6)
10
µA
2, 3
0.475
µA
1
0.95
µA
2, 3
0.475
µA
1
2, 3
±VCC = ±15V
+V
CC
= 5V
+V
CC = 5V, VCM = 1V, RS ≤ 5KΩ
(Note 7)
CC
= 5V, VCM = 3V,
.95
µA
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
-3.8
3.8
mV
1
RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
±VCC = ±15V, VCM = -12V,
-3.8
3.8
mV
1
-6.8
6.8
mV
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
+V
CC
= 5V, VCM = 1V
+V
CC = 5V, VCM = 3V
±VCC = ±15V, VCM = -12V
Output Saturation Voltage
-75
75
nA
1
-100
100
nA
2, 3
-75
75
nA
1
-100
100
nA
2, 3
CC = 5V
(Note 7),
(Note 8)
1.0
3.0
V
1, 2, 3
±VCC = ±15V
(Note 8)
-12
12
V
1, 2, 3
±VCC = ±15V, IO = 25mA,
(Note 6)
1.5
V
1, 2, 3
0.4
V
1, 2
0.6
V
3
10.5
K
4
+V
VI ≤ -5mV
+V
CC
= 3.5V, -VCC = -1V,
VI ≤ -6mV, IO ≤ 3.2mA
AV
Voltage Gain
±VCC = ±15V, Delta VO = 12V,
Common Mode Rejection Ratio
www.national.com
(Note 9)
RL = 1.4KΩ
(Note 9)
10
K
5, 6
+V
(Note 7),
(Note 9)
8.0
K
4
(Note 7),
(Note 9)
5.0
K
5
(Note 7),
(Note 9)
5.8
K
6
80
dB
4
CC = 5V, VCC = 0V,
Delta VO = 4.5V, RL = 1.4KΩ
CMRR
11.5
V+
±VCC = ±15V, VCM = 12V
VSat
1
2, 3
RS ≤ 5KΩ
Input Voltage Range
mA
mA
±VCC = ±15V, VCM = 12V,
VI
11
mA
RS ≤ 5KΩ
Input Offset Current
Subgroups
-4.2
+V
IIO
Units
±VCC = ±15V, VO = Low
(Note 7)
VIO
Max
±VCC = ±15V, VCM = ±12V
8
DC DELTA Parameters
The following conditions apply, unless otherwise specified.
VCM = 0V, Delta calculations performed on QMLV devices at group B, subgroup 5 only.
Symbol
+ICC
Min
Max
Units
Subgroups
-1.0
1.0
mA
1
-0.5
0.5
mA
1
-0.4
0.4
mV
1
Min
Max
Units
Subgroups
±VCC = ±15V
1.0
µA
1
VCC = 5V
1.0
µA
1
Parameter
Positive Supply Current
Conditions
±VCC = ±15V, VO = Low
V+
-ICC
Negative Supply Current
Notes
= 5.6V thru 1.4KΩ
±VCC = ±15V, VO = Low
V+ = 5.6V thru 1.4KΩ
VIO
Input Offset Voltage
+V
CC
= 5V, VCM = 1V, RS ≤ 5KΩ
SMD 5962-9679801, High Dose Rate
100K Post Radiation Parameters @ 25°C
The following conditions apply, unless otherwise specified.
Symbol
IIB
VIO
Parameter
Input Bias Current
Input Offset Voltage
(Note 13)
VCM = 0V
Conditions
Notes
+V
CC
= 5V, VCM = 1V, RS ≤ 5KΩ
-4.0
4.0
mV
1
+V
CC
= 5V, VCM = 3V, RS ≤ 5KΩ
-4.0
4.0
mV
1
-4.0
4.0
mV
1
-4.0
4.0
mV
1
±VCC = ±15V, VCM = 12V, RS ≤
5KΩ
±VCC = ±15V, VCM = −12V, RS ≤
5KΩ
9
www.national.com
LM119QML
SMD 5962-9679801, HIGH DOSE RATE
LM119QML
LM119 Electrical Characteristics
SMD 5962-9679802, ELDRS FREE
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
+ICC
Parameter
Positive Supply Current
Conditions
ILeak
IIB
Negative Supply Current
Output Leakage Current
Input Bias Current
Notes
Min
±VCC = ±15V, VO = Low
V+
-ICC
VCM = 0V
= 5.6V thru 1.4KΩ
Input Offset Voltage
1
-4.5
mA
2
-6.0
mA
3
= 5.6V thru 1.4KΩ
+V
CC = 15V, VCC = -1V,
VGnd = 0V, VO = 35V
(Note 6)
1.8
µA
1
(Note 6)
10
µA
2, 3
0.475
µA
1
0.95
µA
2, 3
0.475
µA
1
2, 3
±VCC = ±15V
+V
CC
= 5V
+V
CC = 5V, VCM = 1V, RS ≤ 5KΩ
(Note 7)
CC
= 5V, VCM = 3V,
.95
µA
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
(Note 7)
-3.8
3.8
mV
1
(Note 7)
-6.8
6.8
mV
2, 3
-3.8
3.8
mV
1
RS ≤ 5KΩ
-6.8
6.8
mV
2, 3
±VCC = ±15V, VCM = -12V,
-3.8
3.8
mV
1
-6.8
6.8
mV
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
(Note 7)
-75
75
nA
1
(Note 7)
-100
100
nA
2, 3
+V
CC
= 5V, VCM = 1V
+V
CC = 5V, VCM = 3V
±VCC = ±15V, VCM = -12V
Output Saturation Voltage
-75
75
nA
1
-100
100
nA
2, 3
-75
75
nA
1
-100
100
nA
2, 3
CC = 5V
(Note 8),
(Note 8)
1.0
3.0
V
1, 2, 3
±VCC = ±15V
(Note 8)
-12
12
V
1, 2, 3
±VCC = ±15V, IO = 25mA,
(Note 6)
1.5
V
1, 2, 3
0.4
V
1, 2
0.6
V
3
10.5
K
4
+V
VI ≤ -5mV
+V
CC
= 3.5V, -VCC = -1V,
VI ≤ -6mV, IO ≤ 3.2mA
AV
Voltage Gain
±VCC = ±15V, Delta VO = 12V,
Common Mode Rejection Ratio
www.national.com
(Note 9)
RL = 1.4KΩ
(Note 9)
10
K
5, 6
+V
(Note 7),
(Note 9)
8.0
K
4
(Note 7),
(Note 9)
5.0
K
5
(Note 7),
(Note 9)
5.8
K
6
80
dB
4
CC = 5V, VCC = 0V,
Delta VO = 4.5V, RL = 1.4KΩ
CMRR
11.5
V+
±VCC = ±15V, VCM = 12V
VSat
1
2, 3
RS ≤ 5KΩ
Input Voltage Range
mA
mA
±VCC = ±15V, VCM = 12V,
VI
11
mA
RS ≤ 5KΩ
Input Offset Current
Subgroups
-4.2
+V
IIO
Units
±VCC = ±15V, VO = Low
(Note 7)
VIO
Max
±VCC = ±15V, VCM = ±12V
10
DC DELTA Parameters
The following conditions apply, unless otherwise specified.
VCM = 0V, Delta calculations performed on QMLV devices at group B, subgroup 5 only.
Symbol
+ICC
Parameter
Positive Supply Current
Conditions
±VCC = ±15V, VO = Low
V+
-ICC
Negative Supply Current
Notes
Min
Max
Units
Subgroups
-1.0
1.0
mA
1
-0.5
0.5
mA
1
-0.4
0.4
mV
1
= 5.6V thru 1.4KΩ
±VCC = ±15V, VO = Low
V+ = 5.6V thru 1.4KΩ
VIO
Input Offset Voltage
+V
CC
= 5V, VCM = 1V, RS ≤ 5KΩ
SMD 5962-9679802, ELDRS FREE
100K Post Radiation Parameters @ 25°C
(Note 14)
The following conditions apply, unless otherwise specified.
Symbol
IIB
VIO
Max
Units
Subgroups
±VCC = ±15V
1.0
µA
1
VCC = 5V
1.0
µA
1
Parameter
Input Bias Current
Input Offset Voltage
VCM = 0V
Conditions
Notes
Min
+V
CC
= 5V, VCM = 1V, RS ≤ 5KΩ
-4.0
4.0
mV
1
+V
CC
= 5V, VCM = 3V, RS ≤ 5KΩ
-4.0
4.0
mV
1
-4.0
4.0
mV
1
-4.0
4.0
mV
1
±VCC = ±15V, VCM = 12V, RS ≤
5KΩ
±VCC = ±15V, VCM = −12V, RS ≤
5KΩ
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package
junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/
θJA or the number given in the Absolute Maximum Ratings, whichever is lower.
Note 4: For supply voltages less than ±15V the absolute maximum input voltage is equal to the supply voltage.
Note 5: Human Body model, 1.5KΩ in series with 100pF.
Note 6: VI ≥ 8mV at extremes for ILeak and VI ≤ −8mV at extremes for VSat (VI to exceed VOS.
Note 7: 5V differential across +VCC and −VCC.
Note 8: Parameter guaranteed by VIO and IIO tests.
Note 9: K = V/mV.
Note 10: Gain is computed with an output swing from +13.5V to +1.5V.
Note 11: Gain is computed with an output swing from +5.0V to +0.5V.
Note 12: Output is monitored by measuring VI with limits from 0 to 6mV at all temperatures
Note 13: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate sensitivity. Radiation end point limits for the noted
parameters are guaranteed only for the conditions as specified in MIL-STD-883, per Test Method 1019, Condition A.
Note 14: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
Low dose rate testing has been performed on a wafer-by-wafer basis, per Test Method 1019, Condition D of MIL-STD-883, with no enhanced low dose rate
sensitivity (ELDRS).
11
www.national.com
LM119QML
SMD 5962-9679802, ELDRS FREE
LM119QML
Typical Performance Characteristics
Input Currents
Common Mode Limits
20143710
20143711
Transfer Function
Response Time for Various
Input Overdrives
20143712
20143713
Response Time for Various
Input Overdrives
Input Characteristics
20143715
20143714
www.national.com
12
LM119QML
Response Time for Various
Input Overdrives
Response Time for Various
Input Overdrives
20143716
20143717
Supply Current
Output Saturation Voltage
20143718
20143719
Supply Current
Output Limiting
Characteristics
20143720
20143721
13
www.national.com
LM119QML
Typical Applications
(Note Pin numbers are for metal can package. )
Relay Driver
20143705
Note 15: Pin numbers are for metal can package.
Window Detector
20143706
VOUT = 5V for VLT ≤ VIN ≤ VUT
VOUT = 0 for VIN ≤ VLTor VIN ≥ VUT
www.national.com
14
Date Released Revision
07/24/08
01/13/09
A
B
Section
Originator
New release to corporate format
Features, Ordering Info., Electrical
Section, Notes 13 and 14
15
Changes
L. Lytle
2 MDS datasheets converted into one
corporate data sheet format. Added Radiation
information. MDS data sheets MNLM119-X
Rev. 0F1 & MDLM119-X Rev 2A2 will be
archived.
Larry McGee
Added reference to ELDRS and Die NSID's to
data sheet. Correction from: 100k rd(Si) to 100
krad(Si) in ordering info. Changed wording in
Notes 13 and 14 Revision A will be Archived.
www.national.com
LM119QML
Revision History
LM119QML
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H10C
Cavity Dual-In-Line Package (J)
NS Package Number J14A
www.national.com
16
LM119QML
Ceramic Flatpack (W)
NS Package Number W10A
Ceramic SOIC (WG)
NS Package Number WG10A
17
www.national.com
LM119QML
Metal Leadless Chip Carrier (LCC)
NS Package Number E20A
www.national.com
18
LM119QML
Notes
19
www.national.com
LM119QML High Speed Dual Comparator
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage Reference
www.national.com/vref
Design Made Easy
www.national.com/easy
PowerWise® Solutions
www.national.com/powerwise
Solutions
www.national.com/solutions
Serial Digital Interface (SDI)
www.national.com/sdi
Mil/Aero
www.national.com/milaero
Temperature Sensors
www.national.com/tempsensors
Solar Magic®
www.national.com/solarmagic
Wireless (PLL/VCO)
www.national.com/wireless
Analog University®
www.national.com/AU
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2009 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
German Tel: +49 (0) 180 5010 771
English Tel: +44 (0) 870 850 4288
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated