54ACQ646,54ACTQ646 54ACTQ646 Quiet Series Octal Transceiver/Register with 3-STATE Outputs Literature Number: SNOS135 54ACTQ646 Quiet Series Octal Transceiver/Register with 3-STATE Outputs General Description Features The ACTQ646 consist of registered bus transceiver circuits, with outputs, D-type flip-flops, and control circuitry providing multiplexed transmission of data directly from the input bus or from the internal storage registers. Data on the A or B bus will be loaded into the respective registers on the LOW-to-HIGH transition of the appropriate clock pin (CPAB or CPBA). The four fundamental handling functions available are illustrated in Figures 1, 2, 3, 4. The ACTQ utilizes FSC Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet Series™ features GTO™ output control and undershoot corrector in addition to a split ground bus for superior performance. n Guaranteed simultaneous switching noise level and dynamic threshold performance n Independent registers for A and B busses n Multiplexed real-time and stored data transfers n 300 mil slim dual-in-line package n Outputs source/sink 24 mA n Faster prop delays than the standard AC/ACT646 n 4 kV minimum ESD immunity n Standard Microcircuit Drawing (SMD) 5962-9219601 Logic Symbols IEEE/IEC DS100326-1 DS100326-2 Pin Descriptions Pin Names A0–A7 Description Data Register A Inputs Data Register A Outputs B0–B7 Data Register B Inputs Data Register B Outputs CPAB, CPBA Clock Pulse Inputs SAB, SBA Transmit/Receive Inputs GTO™ is a trademark of National Semiconductor Corporation FACT™ and FACT Quiet Series™ are trademarks of Fairchild Semiconductor Corporation © 1998 National Semiconductor Corporation DS100326 www.national.com 54ACTQ646 Quiet Series Octal Transceiver/Register with 3-STATE Outputs September 1998 Logic Symbols (Continued) Pin Descriptions Pin Names (Continued) Description G Output Enable Input DIR Direction Control Input Connection Diagram Pin Assignment for DIP and Flatpack DS100326-3 Pin Assignment for LCC DS100326-4 www.national.com 2 Storage from Bus to Register Real Time Transfer A-Bus to B-Bus DS100326-7 DS100326-5 FIGURE 1. FIGURE 3. Real Time Transfer B-Bus to A-Bus Transfer from Register to Bus DS100326-8 DS100326-6 FIGURE 4. FIGURE 2. Function Table Inputs Data I/O (Note 1) G DIR CPAB CPBA H X H or L H or L X X H X N X X X SAB SBA A0–A7 B0–B7 Input Input Function Isolation Clock An Data into A Register H X X N X X Clock Bn Data into B Register L H X X L X An to Bn — Real Time (Transparent Mode) L H N X L X L H H or L X H X A Register to Bn (Stored Mode) L H N X H X Clock An Data into A Register and Output to Bn L L X X X L L L X N X L Input Output Clock An Data into A Register Bn to An — Real Time (Transparent Mode) Output Input Clock Bn Data into B Register L L X H or L X H B Register to An (Stored Mode) L L X N X H Clock Bn Data into B Register and Output to An H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial N = LOW-to-HIGH Transition Note 1: The data output functions may be enabled or disabled by various signals at the G and DIR inputs. Data input functions are always enabled; i.e., data at the bus pins will be stored on every LOW-to-HIGH transition of the appropriate clock inputs. 3 www.national.com Logic Diagram DS100326-9 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.national.com 4 Absolute Maximum Ratings (Note 2) Junction Temperature (TJ) CDIP If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DC Input Diode Current (IIK) VI = −0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = −0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) DC Latch-Up Source or Sink Current 175˚C Recommended Operating Conditions −0.5V to +7.0V Supply Voltage (VCC) ACTQ Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) 54ACTQ Minimum Input Edge Rate ∆V/∆t ACTQ Devices VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V −20 mA +20 mA −0.5V to VCC + 0.5V −20 mA +20 mA −0.5V to VCC + 0.5V ± 50 mA 4.5V to 5.5V 0V to VCC 0V to VCC −55˚C to +125˚C 125 mV/ns Note 2: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT™ circuits outside databook specifications. ± 50 mA −65˚C to +150˚C ± 300 mA DC Electrical Characteristics for ACTQ Symbol Parameter VCC TA = (V) −55˚C to +125˚C Units Conditions Guaranteed Limits VIH VIL VOH VOL IIN Minimum High Level 4.5 2.0 Input Voltage 5.5 2.0 Maximum Low Level 4.5 0.8 Input Voltage 5.5 0.8 Minimum High Level 4.5 4.4 Output Voltage 5.5 5.4 4.5 3.7 5.5 4.7 Maximum Low Level 4.5 0.1 Output Voltage 5.5 0.1 Maximum Input V VOUT = 0.1V V or VCC − 0.1V VOUT = 0.1V V or VCC − 0.1V IOUT = −50 µA V (Note 3) VIN = VIL or VIH IOH = −24 mA V IOH = −24 mA IOUT = 50 µA V (Note 3) VIN = VIL or VIH IOL = 24 mA 4.5 0.5 5.5 0.5 5.5 ± 1.0 µA IOL = 24 mA VI = VCC, GND 5.5 ± 10.0 µA VI = VIL, VIH VO = VCC, GND 5.5 1.6 mA VI = VCC − 2.1V VOLD = 1.65V Max VOHD = 3.85V Min VIN = VCC Leakage Current IOZT Maximum I/O Leakage Current (An, Bn Inputs) ICCT Maximum ICC/Input (Note 4) IOLD Minimum Dynamic 5.5 50 mA IOHD Output Current 5.5 −50 mA ICC Maximum Quiescent 5.5 160.0 µA Supply Current or GND (Note 5) 5 www.national.com DC Electrical Characteristics for ACTQ Symbol Parameter (Continued) VCC TA = (V) −55˚C to +125˚C Units Conditions Guaranteed Limits VOLP Quiet Output 5.0 1.5 V Maximum Dynamic VOL VOLV Quiet Output (Note 6) 5.0 -1.2 V Minimum Dynamic VOL (Note 6) Note 3: All outputs loaded; thresholds on input associated with output under test. Note 4: Maximum test duration 2.0 ms, one output loaded at a time. Note 5: ICC for 54ACTQ @ 25˚C is identical to 74ACQ @ 25˚C. Note 6: Max number of outputs defined as (n). Data inputs are driven 0V to 3V. One output @ GND. AC Electrical Characteristics Symbol Parameter tPLH, Propagation Delay tPHL Clock to Bus tPLH, Propagation Delay tPHL Bus to Bus tPLH, Propagation Delay tPHL SBA or SAB to An or Bn VCC (V) (Note 7) TA = −55˚C to +125˚C CL = 50 pF Units Min Max 5.0 2.0 11.0 ns 5.0 2.0 12.0 ns 5.0 2.0 12.5 ns 5.0 1.5 15.0 ns 5.0 1.5 12.0 ns 5.0 1.5 15.0 ns 5.0 1.5 12.0 ns (w/An or Bn HIGH or LOW) tPZH, Enable Time tPZL G to An or Bn tPHZ, Disable Time tPLZ G to An or Bn tPZH, Enable Time tPZL DIR to An or Bn tPHZ, Disable Time tPLZ DIR to An or Bn Note 7: Voltage Range 5.0 is 5.0V ± 0.5V AC Operating Requirements Symbol TA = −55˚C to +125˚C CL = 50 pF Units Parameter VCC (V) (Note 8) Setup Time, HIGH or LOW 5.0 3.0 ns 5.0 1.5 ns 5.0 4.0 ns Guaranteed Minimum tS Bus to Clock tH Hold Time, HIGH or LOW Bus to Clock tW Clock Pulse Width HIGH or LOW Note 8: Voltage Range 5.0 is 5.0V ± 0.5V www.national.com 6 Capacitance Symbol Parameter Max Units 15 pF CIN Input Capacitance CI/O Input/Output Capacitance 20.0 pF CPD Power Dissipation 100.0 pF Conditions VCC = OPEN VCC = 5.0V VCC = 5.0V Capacitance 7 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead Ceramic Dual-In-Line Package Number J24A 24-Lead Cerpack Package Number W24C www.national.com 8 inches (millimeters) unless otherwise noted (Continued) 28-Lead Leadless Chip Carrier Package Number E28A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. 54ACTQ646 Quiet Series Octal Transceiver/Register with 3-STATE Outputs Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated