TI AFE032

AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Power-Line Communications Analog Front-End
Check for Samples: AFE032
APPLICATIONS
•
•
•
•
•
eMetering
Home Area Networks
Lighting
Solar
Pilot Wires and EVSEs
The AFE032 transmit power amplifier operates from a
single supply in the range of 7 V to 24 V. At typical
load current (IOUT = 1.5 APEAK), a wide output swing
provides a 12-VPP capability with a nominal 15-V
supply.
The device is internally protected against
overtemperature and short-circuit conditions. The
device also provides a selectable current limit. An
interrupt output is provided, indicating current limit,
thermal limit, and undervoltage. A shutdown pin is
also available, and can be used to quickly place the
device into the lowest-power state. Each functional
block can be enabled or disabled to optimize power
dissipation through the serial peripheral interface
(SPI),
DAC_NRF
The AFE032 is housed in a thermally-enhanced,
surface-mount,
PowerPAD,
QFN-48
package.
Operation is specified over the extended industrial
junction temperature range of –40°C to +125°C.
TX_RX_NRF
• Supports:
– CENELEC Bands A, B, C, D
– ARIB STD-T84, FCC
– FSK, SFSK, and NB-OFDM
• Conforms To:
– EN50065-1, -2, -3, -7
– FCC, Part 15
– ARIB STD-T84
• Standards:
– G3, PRIME, P1901.2, ITU-G.hnem
• Programmable Tx Low-Pass Filters and
Rx Band-Pass Filters
• Integrated Power-Line Driver with Thermal and
Overcurrent Protection
• Low-Power Consumption:
– 50 mW (Receiver Mode)
• Receive Sensitivity: 10 μVRMS (Typ)
• Four-Wire SPI™ Interface
• Three Integrated Zero-Crossing Detectors
• Package: QFN-48 PowerPAD™
• Extended Temperature Range:
–40°C to +125°C
2345
The integrated receiver is able to detect signals down
to 10 μVRMS (G3-FCC mode) and is capable of a wide
range of gain options to adapt to varying input-signal
conditions. The monolithic integrated circuit provides
high
reliability
in
demanding
power-line
communication applications.
PA_NRF
FEATURES
1
PA_IN
PA_VS
DVDD
DGND
AVDD1
AVDD2
Bias
and
References
Power
Amplifier
AGND1
The AFE032 is a low-cost, integrated, power-line
communications (PLC), analog front-end (AFE)
device capable of transformer-coupled connections to
the power-line while under the control of a digital
signal processor (DSP) or microcontroller. This
device is ideal for driving high-current, low-impedance
lines up to 1.9 A into reactive loads.
ZC1
ZC_OUT1
ZC2
ZC_OUT2
ZC_OUT3
ZC3
AGND2
PA_GND
SCLK
DIN
DOUT
TSENSE
Digital Interface
(SPI)
AFE032
RX PGA2
RX_PGA2_IN
CS
DAC
RX_PGA2_OUT
SD
DESCRIPTION
PA_OUT ZC_IN3 ZC_IN2 ZC_IN1
PA_ISET
RX_FLAG
TX PGA
Control Registers
Programmable
DAC
TX_FLAG
RX_F_OUT
Filter
RX PGA1
INT
XCLK
DAC_OUT
TX_PGA_IN
RX_PGA1_IN
TX_F_OUT
1
2
3
4
5
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
Illinois Capacitor is a trademark of Illinois Capacitor, Inc.
SPI is a trademark of Motorola Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
(1)
For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
PA_VS
Supply voltage (pins 44, 45)
Pins 3, 4, 6, 7, 8, 10
Pins 13, 21, 28, 31, 32, 38, 39
Voltage (2)
Pins 18, 19
Pin 27
Signal input terminals
Current (2)
Voltage
Signal output terminals
VALUE
UNIT
+26
V
DGND – 0.4 to DVDD + 0.4
V
AGND – 0.4 to AVDD + 0.4
V
PA_GND – 0.4 to PA_VS + 0.4
V
AVDD + 0.4 to 26
V
Pins 3, 4, 6, 7, 8, 10
±10
mA
Pins 13, 21, 28, 31, 32, 38, 39
±10
mA
Pins 18, 19
±10
mA
Pin 35
±10
mA
Pins 5, 9, 47, 48
DGND – 0.4 to DVDD + 0.4
V
Pins 14, 17, 20, 22, 33, 36, 37
AGND – 0.4 to AVDD + 0.4
V
PA_GND – 0.4 to PA_VS + 0.4
V
Pins 42, 43
Current; short-circuit to GND
Pins 5, 9, 47, 48
Continuous
Current; short-circuit to GND
Pins 14, 17, 20, 22, 33, 36, 37
Continuous
Current; short-circuit to GND
Pins 42, 43
Continuous
AVDD
Analog supply voltage (pins 11, 30)
5.5
DVDD
Digital supply voltage
5.5
V
TA
Operating temperature (3)
–40 to +150
°C
Tstg
Storage temperature
–55 to +150
°C
TJ
Junction temperature
+150
°C
Human body model (HBM)
3000
V
Machine model (MM)
200
V
Charged device model (CDM)
500
V
Electrostatic discharge
ratings
ESD
(1)
(2)
(3)
V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and do not imply functional operation of the device at these or any other conditions beyond those indicated. Exposure to absolutemaximum-rated conditions for extended periods may affect device reliability.
Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.4 V beyond the supply rails should
be current limited to 10 mA or less.
The device automatically goes to shutdown above +165°C.
THERMAL INFORMATION
AFE032
THERMAL METRIC (1)
RGZ (QFN)
UNITS
48 PINS
θJA
Junction-to-ambient thermal resistance
22.5
θJCtop
Junction-to-case (top) thermal resistance
12.1
θJB
Junction-to-board thermal resistance
7.5
ψJT
Junction-to-top characterization parameter
2.0
ψJB
Junction-to-board characterization parameter
5.4
θJCbot
Junction-to-case (bottom) thermal resistance
1.7
(1)
2
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS: Transmitter
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
165
171
176
µV
4.8
5.2
MSPS
±0.5%
2%
DAC
Resolution
12-bit DAC, internal VREF = 0.7 V
DR
Data rate (1)
DAC pin high, 12-bit word
GE
Gain error
Full-scale range, TJ = –40°C to +125°C
–2%
DAC OUTPUT
RO
Output resistance
G = 1, f = 100 kHz
1
kΩ
TX_PGA INPUT
(AGND +
0.15) /
gain
Input voltage range
RI
Input resistance
(AVDD – 0.15) /
gain
V
G = 1.15 V/V
52
kΩ
G = 2.3 V/V
34
kΩ
G = 3.25 V/V
26
kΩ
G = 4.6 V/V
20
kΩ
1.15, 2.3, 3.25, 4.6 (2)
G
Gain
V/V
GE
Gain error
Includes DAC, programmable filter,
and TX_PGA for all gains, TJ = –40°C to +125°C
–2%
±0.1%
2%
Gain error drift
Includes DAC, programmable filter,
and TX_PGA for all gains, TJ = –40°C to +125°C
–10
±3
+10
ppm/°C
TX_PGA FREQUENCY RESPONSE
CL = 20 pF, G = 1.15 V/V,
TJ = –40°C to +125°C
30
MHz
CL = 20 pF, G = 2.3 V/V,
TJ = –40°C to +125°C
21.5
MHz
CL = 20 pF, G = 3.25 V/V,
TJ = –40°C to +125°C
17.5
MHz
CL = 20 pF, G = 4.6 V/V,
TJ = –40°C to +125°C
15.5
MHz
CEN-A
35 kHz to 95 kHz
370
µVRMS
CEN-B
95 kHz to 125 kHz
220
µVRMS
CEN-C
125 kHz to 140 kHz
160
µVRMS
CEN-D
140 kHz to 148 kHz
98
µVRMS
ARIB STD-T84
35 kHz to 420 kHz
640
µVRMS
FCC-LOW
35 kHz to 125 kHz
384
µVRMS
G3-FCC
150 kHz to 490 kHz
565
µVRMS
Bandwidth (3)
BW
TX PATH TRANSMITTER NOISE
Integrated noise
at PA output (5)
(4)
POWER AMPLIFIER (PA) INPUT
Input voltage range
For linear operation
(PA_GND
+ 0.4) /
gain
Input impedance
(PA_VS – 0.4) /
gain
V
17
kΩ
PA FREQUENCY RESPONSE
BW
Bandwidth
ILOAD = 0 mA
SR
Slew rate
PA_VS = 24 V, 20-V step
Full-power bandwidth
PA_VS = 24 V, VOUT = 20 VPP
Power-supply rejection ratio
RTI, dc to f = 50 kHz
PSRR
(1)
(2)
(3)
(4)
(5)
3.4
80
3.82
4.23
MHz
75
V/µs
1
MHz
94
dB
Refer to the Application Information section.
This parameter is from DAC_OUT to TX_F_OUT. This parameter includes the LPF gain error and is the dc gain. Adding LPF causes
some loss of gain flatness.
This parameter is internal to the device. Bandwidth is designed and simulated over corners to ensure a low-distortion PGA in the
application.
Includes the DAC, programmable filter, TX_PGA, and PA noise-reducing capacitor = 1 nF from DAC_NRF to ground, PA_NRF to
ground, and TX_RF_NRF to ground.
Includes the DAC, TX_PGA (gain = 4.6), LPF, and PA.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
3
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS: Transmitter (continued)
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PA OUTPUT
From PA_VS
Voltage output
swing
VO
From PA_GND
IO = 200-mA sourcing, 1-ms pulse
0.5
V
IO = 1.5-A sourcing, 1-ms pulse
2.25
V
IO = 200 mA sinking, 1-ms pulse
0.5
V
IO = 1.5-A sinking, 1-ms pulse
1.5
V
Maximum continuous current, dc
Pin 26 connected to ground,
REG_PA_CURRENT_CFG[5:4] = 11
Output resistance
IO = 1.9 A, f = 500 kHz
PA disabled output impedance
f = 100 kHz, PA_NRF enabled
Resistor-selectable
Output current
limit
Digitally-selectable (6)
RSET connected from pin 26 to ground
1.9
A
Ω
0.1
130 || 105
kΩ || pF
See the Application Information section
Pin 26 connected to ground,
REG_PA_CURRENT_CFG[5:4] = 00
1.25
A
Pin 26 connected to ground,
REG_PA_CURRENT_CFG[5:4] = 01
1.8
A
Pin 26 connected to ground,
REG_PA_CURRENT_CFG[5:4] = 10
2.5
A
Pin 26 connected to ground,
REG_PA_CURRENT_CFG[5:4] = 11
3.0
A
+165
°C
+15
°C
+150
°C
PA THERMAL SHUTDOWN
Junction temperature at shutdown
Hysteresis
Return to normal operation
PA TSENSE DIODE
η
Diode ideality factor
1.03
PA GAIN
G
Nominal gain
PA_OUT / PA_IN
GE
Gain error
TJ = –40°C to +125°C
Gain error drift
TJ = –40°C to +125°C
(6)
(7)
4
7.4 (7)
–2%
0.1%
±5
V/V
2%
ppm/°C
Refer to the Application Information section.
This gain reflects a direct measurement on the PA block by itself. The gain in the signal chain composed by Tx PGA, Tx Filter and PA
equals the Tx PGA gain multiplied by 7 V/V (where 7 V/V is the gain of the PA block when its input is capacitively coupled to the Tx
Filter output). Refer to the Power Amplifier Block section for more information.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS: Programmable Filter
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LOW-PASS FILTER (LPF)
Cutoff
frequencies
in Tx
mode (1)
CEN-A
1-dB gain flatness, TJ = –40°C to +125°C
94
102
110
kHz
CEN-B, CEN-C, CEN-D, FCC-LOW
1-dB gain flatness, TJ = –40°C to +125°C
148
160
172
kHz
ARIB STD-T84
1-dB gain flatness, TJ = –40°C to +125°C
405
435
475
kHz
G3-FCC
1-dB gain flatness, TJ = –40°C to +125°C
470
505
540
kHz
Transition time
Rx to Tx
PA_NRF, TX_RX_NRF, and DAC,
TJ = –40°C to +125°C
Tx to Rx
NRF enabled, TJ = –40°C to +125°C
80 (2)
µs
30
µs
1
kΩ
LPF OUTPUT
RO
Output impedance
f = 100 kHz
HIGH-PASS FILTER (HPF)
CEN-A, CEN-B, CEN-C, CEN-D,
ARIB STD-T84, FCC-LOW
1-dB gain flatness, TJ = –40°C to +125°C
30
35
40
kHz
G3-FCC
1-dB gain flatness, TJ = –40°C to +125°C
120
132
152
kHz
Transition time
PA_NRF, TX_RX_NRF, and DAC,
TJ = –40°C to +125°C
Rx to Tx
Tx to Rx
NRF enabled, TJ = –40°C to +125°C
30
µs
(2)
µs
1
kΩ
80
HPF OUTPUT
RO
(1)
(2)
Output impedance
f = 100 kHz
These cutoff frequencies are only valid when the filter is used as a low-pass filter. Refer to the Register Map section in the Application
Information for register settings.
See the Application Information section for the start-up procedure.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
5
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS: Receiver
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
RX_PGA1 INPUT
Input voltage range
For linear operation
(AGND +
0.15) /
gain
G = 0.125 V/V
RI
Input resistance
(AVDD – 0.15) /
gain
V
111.1
kΩ
G = 0.25 V/V
100
kΩ
G = 0.5 V/V
133
kΩ
G = 1 V/V
100
kΩ
G = 2 V/V
66
kΩ
G = 4 V/V
40
kΩ
G = 8 V/V
22
kΩ
G = 16 V/V
12
kΩ
G = 32 V/V
6
kΩ
RX_PGA1 GAIN
0.125, 0.25, 0.5,
1, 2, 4, 8, 16, 32
DC gain
GE
Gain error
For all gains, TJ = –40°C to +125°C
Gain error drift
TJ = –40°C to +125°C
–5%
V/V
5%
±100
ppm/°C
RX_PGA1 FREQUENCY RESPONSE
BW
Bandwidth
CL = 20 pF, G = 0.125 V/V
47
MHz
CL = 20 pF, G = 0.25 V/V
18
MHz
CL = 20 pF, G = 0.5 V/V
6
MHz
CL = 20 pF, G = 1 V/V
4
MHz
CL = 20 pF, G = 2 V/V
3
MHz
CL = 20 pF, G = 4 V/V
2.5
MHz
CL = 20 pF, G = 8 V/V
2.1
MHz
CL = 20pF, G = 16 V/V
1.85
MHz
CL = 20 pF, G = 32 V/V
1.55
MHz
RX_PGA2 INPUT
Input voltage range
RI
6
Input resistance
For linear operation
(AVDD –
0.15)/
gain
(AGND + 0.15) /
gain
V
G = 1 V/V
54
kΩ
G = 4 V/V
21
kΩ
G = 16 V/V
5.5
kΩ
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS: Receiver (continued)
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Rx_PGA2 GAIN
G
Gain
GE
Gain error
For all gains, TJ = –40°C to +125°C
1, 4, 16
Gain error drift
TJ = –40°C to +125°C
±100
ppm/°C
CL = 20 pF, G = 1 V/V
6.73
MHz
CL = 20 pF, G = 4 V/V
5
MHz
CL = 20 pF, G = 16 V/V
3
MHz
G = 1, f = 100 kHz
1
kΩ
CEN-A
35 kHz to 95 kHz
10
µVRMS
CEN-B
95 kHz to 125 kHz
5
µVRMS
CEN-C
125 kHz to 140 kHz
3
µVRMS
CEN-D
140 kHz to 148 kHz
2
µVRMS
ARIB STD-T84
35kHz to 400 kHz
12
µVRMS
FCC-LOW
35 kHz to 125 kHz
11
µVRMS
G3-FCC
150 kHz to 490 kHz
10
µVRMS
–2%
V/V
2%
RX_PGA2 FREQUENCY RESPONSE
BW
Bandwidth
RX_PGA2 OUTPUT
Output resistance
RX PATH SENSITIVITY
(1)
Input-referred
integrated noise
(1)
Noise-reducing capacitor = 1 nF from TX_RX_NRF to ground, RX_PGA1 = 32, and RX_PGA2 = 1.
ELECTRICAL CHARACTERISTICS: Noise-Reducing Filters
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PA_NRF
Bias voltage
ROUT
Output resistance
tON
Turn-on time
tOFF
Turn-off time
VPAV
Noise-reducing capacitor = 1 nF from
PA_NRF to ground
/2
V
4
kΩ
250
ms
10
µs
S
TX_RX_NRF
Bias voltage
VAVDD / 2
V
1
kΩ
10
µs
Turn-off time
10
µs
Bias voltage
VAVDD / 4.7
V
1
kΩ
10
µs
10
µs
ROUT
Output resistance
tON
Turn-on time
tOFF
Noise-reducing capacitor = 1 nF from
TX_RX_NRF to ground
DAC_NRF
ROUT
Output resistance
tON
Turn-on time
tOFF
Turn-off time
Noise-reducing capacitor = 1 nF from
DAC_NRF to ground
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
7
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS: Digital
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
–1
0.01
1
UNIT
DIGITAL INPUTS (SCLK, DI, CS, SD, DAC, XCLK)
0 V ≤ VIN ≤ DVDD
Leakage input current
VIH
High-level input voltage
VIL
Low-level input voltage
0.7 × DVDD
µA
V
0.3 × DVDD
V
SD pin function
(active high)
SD pin high
SD > 0.7 × DVDD
SD pin low
SD < 0.3 × DVDD
DAC pin function
(active high)
DAC pin high
DAC > 0.7 × DVDD
SPI access to DAC registers
DAC pin low
DAC < 0.3 × DVDD
SPI access to command and data registers
XCLK frequency range
XCLK jitter < 180 ps
Device in shutdown
Device in normal operation
5
40
MHz
DIGITAL OUTPUTS (DO, ZC_OUT)
VOH
High-level output voltage
IOH = 3 mA
VOL
Low-level output voltage
IOL = –3 mA
DVDD – 0.4
GND
DVDD
V
GND + 0.4
V
1
µA
DIGITAL OUTPUTS (INT, TX_FLAG, RX_FLAG)
IOH
High-level output current
VOH = 3.3 V
VOL
Low-level output voltage
IOL = 4 mA
IOL
Low-level output current
VOL = 400 mV
INT pin (active low,
open-drain)
INT pin high
INT sink high < 1 µA
INT pin low
INT < 0.4 V
TX_FLAG (active low, TX_FLAG pin high
open-drain)
TX_FLAG pin low
TX_FLAG sink high < 1 µA
RX_FLAG pin high
RX_FLAG sink high < 1 µA
RX_FLAG pin low
RX_FLAG < 0.4 V
RX_FLAG (active
low, open-drain)
TX_FLAG < 0.4 V
0.4
4
V
mA
Normal operation
Interrupt has occurred
Tx block disabled
Tx block ready
Rx block disabled
Rx block ready
GAIN TIMING
Gain select time
0.2
µs
SHUTDOWN MODE TIMING
Enable time
SD pin transitions from high to low
3
ms
Disable time
SD pin transitions from low to high
2
ms
DVDD ≥ 2 V
3
ms
POR TIMING
Power-on reset power-up time
8
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
ELECTRICAL CHARACTERISTICS: Zero-Crossing Detector
At TCASE = +25°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Input voltage range
AGND
AVDD
Input current range
–10
10
RIN
Input resistance
CIN
Input capacitance
AGND ≤ VIN ≤ AVDD
UNIT
V
mA
2
MΩ
4
pF
Rising threshold
0.45
0.9
1.35
V
Falling threshold
0.25
0.5
0.75
V
0.2
0.4
0.6
Hysteresis
Jitter
50 Hz and 60 Hz, 240 VRMS and 120 VRMS
V
10
ns
ELECTRICAL CHARACTERISTICS: Power Supply
At TCASE = +25°C, TJ = –40°C to +125°C, VPAVS = 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
15
24
UNIT
OPERATING SUPPLY RANGE
PA_VS
Power amplifier
DVDD
Digital supply
7
3.3
V
V
AVDD
Analog supply
3.3
V
QUIESCENT CURRENT (SD pin low)
IQPA_VS
Power amplifier
IO = 0 V, PA = on (1),
REG_PA_CURRENT_CFG[7:6] = 00
40
48
56
mA
IO = 0 V, PA = on (1),
REG_PA_CURRENT_CFG[7:6] = 01
68
78
88
mA
IO = 0 V, PA = on (1),
REG_PA_CURRENT_CFG[7:6] = 10
84
96
108
mA
IO = 0 V, PA = on (1),
REG_PA_CURRENT_CFG[7:6] = 11
10
17
24
mA
(2)
1.5
2.5
3.5
mA
Rx configuration (3)
1.1
2.1
3.1
mA
Tx configuration
IQDVDD
Digital supply
All blocks disabled
IQAVDD
Analog supply
(4)
330
450
µA
Tx configuration (3)
8
11
14
mA
Rx configuration (4)
9
13
17
mA
25
100
µA
All blocks disabled (4)
SHUTDOWN
SDPA_VS
Power amplifier
SD pin high
40
150
µA
SDDVDD
Digital supply
SD pin high
330
400
µA
SDAVDD
Analog supply
SD pin high
25
50
µA
(1)
(2)
(3)
(4)
PA and PA output enabled.
The DAC, TX_PGA, low-pass filter, PA, PA_NRF, TX_RX_NRF, and DAC_NRF blocks are enabled in the Tx configuration. All other
blocks are disabled.
The RX_PGA1, high-pass filter, low-pass filter, RX_PGA2, and TX_RX_NRF blocks are enabled in the Rx configuration. All other blocks
are disabled.
All internal blocks disabled, SD pin low.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
9
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
SPI TIMING REQUIREMENTS
PARAMETER
MIN
Input capacitance
TYP
MAX
1
UNIT
pF
tRFI
Input rising and falling time (CS, DIN, SCLK)
tRFO
DOUT rising and falling time
tCSH
CS high time
10
DAC_CLK
cycles (1)
tCS0
SCLK edge to CS falling edge setup time
10
ns
tCSSC
CS falling edge to first SCLK edge setup time
10
fSCLK
SCLK frequency
tHI
SCLK high time
16.7
25
ns
tLO
SCLK low time
16.7
25
ns
tSCCS
SCLK last edge to CS rising edge setup time
10
ns
tCS1
CS rising edge to SCLK edge setup time
10
ns
tSU
DIN setup time
5
ns
tHD
DIN hold time
5
tDO
SCLK to DOUT valid propagation delay
16
ns
tsoz
CS rising edge to DOUT forced to Hi-Z
20
ns
(1)
10
2
ns
10
ns
ns
20
30
MHz
ns
CS pin must remain high for at least ten DAC_CLK cycles after a write operation and must remain high for at least five DAC_CLK cycles
after a read operation.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
TIMING DIAGRAMS
tCSH
CS
tCSSC
tSCCS
tLO
tCS1
tCS0
tHI
SCLK
tSU
1/fSCLK
tHD
DIN
tSOZ
tDO
Hi-Z
Hi-Z
DOUT
Figure 1. SPI Mode 0,0
tCSH
CS
tCSSC
tSCCS
tHI
tCS1
tCS0
tLO
SCLK
tSU
tHD
1/fSCLK
DIN
tDO
Hi-Z
tSOZ
Hi-Z
DOUT
Figure 2. SPI Mode 1,1
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
11
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
PIN CONFIGURATION
RX_FLAG
TX_FLAG
PA_VS3
PA_VS1
PA_VS2
PA_OUT1
PA_OUT2
PA_GND1
PA_GND2
ZC_IN1
ZC_IN2
ZC_OUT1
RGZ PACKAGE
QFN-48
(TOP VIEW)
48
47
46
45
44
43
42
41
40
39
38
37
DGND
1
36
ZC_OUT2
DVDD
2
35
TSENSE
SCLK
3
34
DNC
DIN
4
33
ZC_OUT3
DOUT
5
32
ZC_IN3
CS
6
31
PA_GND3
Thermal Pad
XCLK 10
27
RX_PGA1_IN
AVDD1 11
26
PA_ISET
AGND1 12
25
NC
13
14
15
16
17
18
19
20
21
22
23
24
DGND2
TX_RX_NRF
NC
28
RX_F_OUT
9
RX_PGA2_IN
INT
RX_PGA2_OUT
AGND2
PA_NRF
29
PA_IN
8
TX_F_OUT
SD
DAC_NRF
AVDD2
DNC
30
DAC_OUT
7
TX_PGA_IN
DAC
NOTE: Connect exposed thermal pad to ground.
12
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
PIN DESCRIPTIONS
NAME
PIN NO.
AGND1
12
Analog ground
DESCRIPTION
AGND2
29
Analog ground
AVDD1
11
Analog supply
AVDD2
30
Analog supply
CS
6
SPI digital chip-select input
DAC
7
DAC mode select digital input
DAC_OUT
14
DAC analog output
DAC_NRF
16
DAC noise-reducing filter analog input
DGND
1
Digital ground
DGND2
24
Digital ground
DIN
4
SPI digital input
DNC
15, 34
Do not connect
DOUT
5
SPI digital output (push or pull)
DVDD
2
Digital supply
INT
9
Interrupt on undervoltage, undercurrent, or thermal overload (digital output, open-drain, active low)
NC
23, 25
PA_GND1
41
Power amplifier ground
PA_GND2
40
Power amplifier ground (connect to PA_GND1, pin 41)
PA_GND3
31
Power amplifier ground (connect to PA_GND1, pin 41)
PA_IN
18
Power amplifier analog input
PA_ISET
26
Power amplifier current-limit adjust pin (left open if not used)
PA_NRF
19
Power amplifier noise-reducing filter analog input
PA_OUT1
43
Power amplifier output
PA_OUT2
42
Power amplifier output (connect to PA_OUT1, pin 43)
PA_VS1
45
Power amplifier supply
PA_VS2
44
Power amplifier supply (connect to PA_VS1, pin 45)
PA_VS3
46
Power amplifier supply (connect to PA_VS1, pin 45)
RX_F_OUT
22
Receiver filter analog output
No internal connection (connect to GND or leave unconnected)
RX_FLAG
48
Receiver ready flag (digital output, open-drain, active low)
RX_PGA1_IN
27
Receiver PGA1 analog input
RX_PGA2_IN
21
Receiver PGA2 analog input
RX_PGA2_OUT
20
Receiver PGA2 analog output
SCLK
3
SPI serial clock input
SD
8
System shutdown digital input (active high)
TSENSE
35
Analog temperature sensing diode (anode)
TX_F_OUT
17
Transmit filter analog output
TX_FLAG
47
Transmitter ready flag (digital output, open-drain, active low)
TX_PGA_IN
13
Transmitter PGA analog input
TX_RX_NRF
28
Transmitter and receiver noise-reducing filter analog input
XCLK
10
DAC clock digital input
ZC_IN1
39
Zero-crossing detector 1, analog input
ZC_IN2
38
Zero-crossing detector 2, analog input
ZC_IN3
32
Zero-crossing detector 3, analog input
ZC_OUT1
37
Zero-crossing detector 1, digital output (push or pull)
ZC_OUT2
36
Zero-crossing detector 2, digital output (push or pull)
ZC_OUT3
33
Zero-crossing detector 3, digital output (push or pull)
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
13
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
DAC_NRF
TX_RX_NRF
PA_NRF
FUNCTIONAL BLOCK DIAGRAM
PA_IN
PA_VS
PA_OUT ZC_IN3 ZC_IN2 ZC_IN1
PA_ISET
DVDD
DGND
AVDD1
AVDD2
Bias
and
References
Power
Amplifier
AGND1
ZC1
ZC_OUT1
ZC2
ZC_OUT2
ZC3
ZC_OUT3
AGND2
PA_GND
SCLK
DIN
DOUT
TSENSE
Digital Interface
(SPI)
AFE032
RX PGA2
RX_PGA2_IN
CS
DAC
RX_PGA2_OUT
SD
RX_FLAG
TX PGA
Control Registers
Programmable
DAC
TX_FLAG
Filter
RX PGA1
INT
XCLK
14
RX_F_OUT
DAC_OUT
TX_PGA_IN
Submit Documentation Feedback
RX_PGA1_IN
TX_F_OUT
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
TYPICAL CHARACTERISTICS
V S
= 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
10
0
0
-20
-10
-40
-20
-60
Gain (dB)
Gain (dB)
At TJ = +25°C, VPA
-30
90 kHz (CENELEC A)
-40
-80
-100
35 kHz - 140 kHz (CENELEC A to D)
150 kHz - 420 kHz (ARIB)
150 kHz - 490 kHz (FCC)
140 kHz (CENELEC B to D)
-50
-120
420 kHz (ARIB)
490 kHz (FCC)
-60
1000
10k
100k
1M
-140
1000
10M
Frequency (Hz)
1M
10M
C001
Figure 4. Rx BAND-PASS FILTER GAIN vs FREQUENCY
10-5
Noise Density (9¥+])
10-5
Noise Density (9¥+]
100k
Frequency (Hz)
Figure 3. Tx, Rx LOW-PASS FILTER GAIN vs FREQUENCY
10-6
10-7
10-6
10-7
10-8
Gain (RX PGA1) = 32
Gain (RX PGA2) = 1
10-8
10k
Gain = 4.6
100k
10-9
10k
1M
Frequency (Hz)
100k
1M
10M
100M
Frequency (Hz)
C003
Figure 5. Rx PATH NOISE DENSITY
C004
Figure 6. Tx PATH NOISE DENSITY
20
140
15
120
10
100
5
PSRR (dB)
Gain (dB)
10k
C002
0
-5
80
60
40
-10
20
-15
-20
0
10k
100k
1M
10M
100M
Frequency (Hz)
1
C00
Figure 7. PA GAIN vs FREQUENCY
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Product Folder Links: AFE032
C00
Figure 8. PA PSRR vs FREQUENCY
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
100M
15
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VPA
V S
= 15 V, and VAVDD = VDVDD = 3.3 V, unless otherwise noted.
15
120
110
PA Output (OFDM Signal)
100
90
10
Level (dBµV)
Output Voltage (V)
12.5
7.5
positive Load
5
80
70
ARIB Spectrum Mask
60
50
negative Load
40
2.5
30
0
20
0
0.5
1
1.5
2
2.5
3
Load Current (A)
3.5
0
200k
400k
600k
800k
Frequency (Hz)
C00
Figure 9. PA OUTPUT vs OUTPUT LOAD
1M
C005
Figure 10. ARIB CONDUCTED EMISSIONS
120
110
PA Output (OFDM Signal)
100
Level (dBµV)
90
80
70
FCC Spectrum Mask
60
50
40
30
20
0
200k
400k
600k
800k
Frequency (Hz)
1M
C006
Figure 11. FCC CONDUCTED EMISSIONS
16
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
APPLICATION INFORMATION
GENERAL DESCRIPTION
The AFE032 is an integrated, power-line communication, analog front-end device that functions in conjunction
with a microcontroller. The device conditions data generated in a microcontroller and transmits such data onto
power lines through a line-coupling circuit.
The device includes several primary functional blocks:
• A power amplifier (PA) transmits data onto power lines through a line-coupling circuit.
• The transmit path (Tx) consists of a high-precision, digital-to-analog converter (DAC), programmable amplifier
(TX_PGA), and low-pass filter (LPF).
• The receive path (Rx) consists of two programmable amplifiers (RX_PGA1 and RX_PAG2) and a band-pass
filter [(an LPF and a high-pass filter (HPF)].
BLOCK DESCRIPTIONS
Power Amplifier Block
The power amplifier (PA) block consists of a high slew rate, high-voltage, and high-current operational amplifier.
The PA is configured with an inverting gain of 7 V/V, has a low-pass filter response, and maintains excellent
linearity and low distortion throughout its bandwidth. The PA is specified to operate from 7 V to 24 V and can
deliver up to ±1.9 A of continuous output current over the specified junction temperature range of –40°C to
+125°C. The PA block is shown in Figure 12.
PA_VS1,
PA_VS2,
PA_VS3
TSENSE
Inside the Device
Power Amplifier
17 k:
PA_OUT1,
PA_OUT2
PA_IN
PA_ISET
PA_GND1,
PA_GND2,
PA_GND3
Figure 12. PA Block Equivalent Circuit
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
17
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Connecting the PA in a typical power line communication (PLC) application requires few additional components.
Figure 13 shows the typical connections to the PA block.
PA Supply
47 PF
100 nF
PA_VS1,
PA_VS2,
PA_VS3
TSENSE
Inside the Device
PA_IN
PA_OUT1,
PA_OUT2
Power Amplifier
17 k:
CIN
PA_ISET
Optional
RSET
PA_GND1,
PA_GND2,
PA_GND3
Figure 13. Typical Connections to the PA
The external capacitor (CIN) introduces a single-pole, high-pass characteristic to the PA transfer function. The CIN
and PA combination has a band-pass response because of the inherent low-pass transfer function from the PA.
The value of the high-pass cutoff frequency is determined by CIN reacting with the input resistance of the PA
circuit, and can be determined by Equation 1:
1
CIN =
2 ´ p ´ 18 kW ´ fHP
where:
•
•
CIN = external input capacitor and
fHP = desired high-pass cutoff frequency.
(1)
For example, setting CIN to 3.3 nF results in a high-pass cutoff frequency of 2.9 kHz. The voltage rating for CIN
should be determined to withstand operation up to the PA power-supply voltage.
When the transmitter is not in use, the output can be disabled and placed in a high-impedance state by following
the procedure outlined in the Power Amplifier Enable Sequence section.
Refer to the Initialization Sequence and Power Amplifier Enable Sequence sections for details on the proper
sequence when enabling the power amplifier.
18
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
PA Current Limiting
The PA_ISET pin (pin 26) provides a resistor-programmable output current limit for the PA block. Equation 2
determines the value of the external RSET resistor attached to this pin.
1.2 V ´ 16.320 kW
ILIM =
RINT + RSET
where:
•
•
•
RSET = the value of the external resistor connected between pin 26 and ground,
RINT = the value of the internal resistor as programmed by the SPI interface in Table 18 (bits 4 and 5), and
Ilim = the value of the desired current limit for the PA.
(2)
RINT bit setting for bits 4 and 5 in Table 18 are listed in Table 1.
Table 1. RINT Bit Settings
BIT SETTING
RINT VALUE
00
17 kΩ
01
11 kΩ
10
8 kΩ
11
1.2 kΩ
Note that there is a 30% tolerance on the Ilim value given by Equation 2.
Tx Block
The Tx block consists of the Tx PGA and Tx filter.
The Tx PGA is a low-noise, high-performance, programmable gain amplifier. In DAC mode [where the DAC pin,
pin 7, is a logic '1' and Tx enable (bit 4 in the REG_RX/TX_CTL register) is a logic '1'], the Tx PGA operates as
the internal digital-to-analog converter (DAC) output buffer with programmable gain. The Tx PGA gain is
programmed through the serial interface. The Tx PGA gain settings are 1.15 V/V, 2.3 V/V, 3.25 V/V, and 4.6 V/V.
Gain is selectable via the TX_PGA gain pins (bits 2 to 0 in the REG_RX/TX_CTL register).
The Tx filter is a unity-gain, fourth-order, low-pass filter. The Tx filter cutoff frequency is selectable between the
CENELEC (bands A, B, C, or D), ARIB, or FCC modes. The LPF band select bits (bits 6 to 4 in the
REG_HPF/LPF_CFG register) determine the cutoff frequency.
When in DAC mode, the device accepts serial data from the microprocessor and writes that data to the internal
DAC registers.
Proper connections for the Tx signal path for DAC mode operation are shown in Figure 14.
ZF
Inside the Device
SCLK
TX PGA
DIN
DOUT
Digital Interface
(SPI)
PA_OUT2
Programmable
Power Amplifier
DAC
1 k:
Filter
ZIN
PA_OUT1
1 k:
CS
17 k:
XCLK
DAC_OUT
TX_PGA_IN
TX_F_OUT
CDAC
PA_IN
CIN
C IN
1
2 u S u 18k: u f HP
(1) For the capacitor value of CIN, fHP is the desired lower cutoff frequency and 17 kΩ is the PA input resistance.
Figure 14. Recommended Tx Signal Chain Connections
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
19
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
The capacitors listed in Figure 14 should be rated to withstand the full AVDD power-supply voltage for CDAC and
PA_VS for CIN.
Rx Block
The Rx block consists of the Rx PGA1, Rx filter, and Rx PGA2. Both Rx PGA1 and Rx PGA2 are highperformance programmable gain amplifiers that can be configured through the SPI interface.
Rx PGA1 can operate as either an attenuator or in gain. The Rx PGA1 gain steps are 0.125 V/V, 0.25 V/V, 0.5
V/V, 1 V/V, 2 V/V, 4 V/V, 8 V/V, 16 V/V, and 32 V/V. Gains are selectable with the RX_PGA1 gain bits (bits 7 to
4 in the REG_RXPGA_CFG register). Configuring the Rx PGA1 as an attenuator (at gains less than 1 V/V) is
useful for applications where large interference signals are present within the signal band. Attenuating the large
interference allows these signals to pass through the analog Rx signal chain without causing an overload; the
interference signal can then be processed and removed within the microprocessor as necessary. Similarly, if a
transmitter is located close to the receiver, gains less than 1 V/V may be needed.
The Rx PGA2 gain steps are 1 V/V, 4 V/V, and 16 V/V. Gains are selectable through the RX_PGA2 gain bits
(bits 3 to 1 in the REG_RXPGA_CFG register).
The Rx filter is a very low-noise, unity-gain, fourth-order, low-pass or band-pass filter. The Rx filter cutoff
frequency is selectable between the CENELEC (bands A, B, C, or D), ARIB, or FCC modes. The LPF band
select bits (bits 6 to 4 of the REG_HPF/LPF_REG register) determine the cutoff frequency for the LPF. The HPF
band select bits (bits 1 and 2 of the REG_HPF/LPF_REG register) set up the cutoff frequency of the HPF.
Recommended connections for the Rx signal chain are shown in Figure 15.
Inside the Device
RX_PGA1
RX_PGA1_IN
From line-coupling circuit
or passive band-pass filter.
C1
330 :
To ADC input of MCU.
RRXPGA1IN
C1
RX_PGA2
Programmable
1 k:
Filter
RX_PGA2_ OUT
1
2 u S u f u R RXPGA 1 IN
1 k:
RRXPGA2IN
RX_PGA2_IN
RX_F_OUT
C2
C2
1
2 u S u f u ( R RXPGA 2 IN 1k: )
(1) For capacitor value C1, f is the desired lower cutoff frequency and RRXPAG1IN is the input resistance of RX_PGA1.
(2) For capacitor value C2, f is the desired lower cutoff frequency and RRXPAG2IN is the input resistance of RX_PGA2.
Figure 15. Recommended Connections for Rx Signal Chain
Figure 16 shows, a fourth-order, passive band-pass filter that is optional but recommended for applications with
high performance needs. The external passive band-pass filter removes unwanted, out-of-band signals from the
signal path, and it prevents such signals from reaching the active internal filters within the device.
R3
L3
From Line-Coupling Circuit
To RX_PGA1 Input
C3
C1
R4
C4
C1
L4
1
2 u S u f u RRXPGA1IN
(1) For capacitor value C1, f is the desired lower cutoff frequency and RRXPGA1IN is the input resistance of RX_PGA1.
Figure 16. Passive Band-Pass Rx Filter
20
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
The following steps can be used to quickly design the passive pass-band filter. (Note that these steps produce
an approximate result.)
1. Choose the filter characteristic impedance, ZC:
– For a –6-db passband attenuation: R3 = R4 = ZC.
– For a 0-db passband attenuation: R4 = ZC, R3 = 10 × ZC.
2. Calculate values for C3, C4, L3, and L4 using the following equations:
1
C3 =
2 ´ p ´ f3 ´ ZC
1
C4 =
2 ´ p ´ f4 ´ ZC
L3 =
ZC
2 ´ p ´ f3
L4 =
ZC
2 ´ p ´ f4
Table 2 and Table 3 show standard values for common applications.
Table 2. Recommended Component Values for Fourth-Order Passive Band-Pass Filters (0-dB Pass-Band
Attenuation)
FREQUENCY
RANGE
(kHz)
CHARACTERISTIC
IMPEDANCE
R3
R4
(kΩ)
C3
(nF)
C4
(nF)
L3
(μH)
L4
(μH)
CENELEC A
35 to 95
1 kΩ
1 kΩ
10
4.7
1.5
1500
4700
CENELEC B, C, D
95 to 150
1 kΩ
1 kΩ
10
1.7
1
1200
1500
SFSK
63 to 74
1 kΩ
1 kΩ
10
2.7
2.2
2200
2200
FCC and ARIB
15 to 600
100 Ω
100 Ω
1
100
2.2
27
1000
FREQUENCY BAND
Table 3. Recommended Component Values for Fourth-Order Passive Band-Pass Filters (–6-dB PassBand Attenuation)
FREQUENCY
RANGE
(kHz)
CHARACTERISTIC
IMPEDANCE
R3
R4
C3
(nF)
C4
(nF)
L3
(μH)
L4
(μH)
CENELEC A
35 to 95
1 kΩ
1 kΩ
1 kΩ
4.7
1.5
1500
4700
CENELEC B, C, D
95 to 150
1 kΩ
1 kΩ
1 kΩ
1.7
1
1200
1500
SFSK
63 to 74
1 kΩ
1 kΩ
1 kΩ
2.7
2.2
2200
2200
FCC and ARIB
15 to 600
100 Ω
100 Ω
100 Ω
100
2.2
27
1000
FREQUENCY BAND
Avoid excessive capacitive loading when laying out the printed circuit board (PCB) traces from the inputs or
outputs of the Rx block components. Keeping the PCB capacitance from the inputs to ground, or outputs to
ground, below 100 pF is recommended.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
21
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Figure 17 shows the complete Rx signal path, including the optional passive band-pass filter.
Inside the Device
R3
RX_PGA1
RX_PGA1_IN
L3
RX_PGA2
Programmable
330 :
From Line-Coupling Circuit
To ADC Input of MCU
RRXPGA1IN
C1
C3
1 k:
Filter
RRXPGA2IN
1 k:
R4
C4
RX_PGA2_OUT
L4
C1
RX_F_OUT
1
2 u S u f u R RXPGA 1 IN
RX_PGA2_IN
C2
C2
1
2 u S u f u ( R RXPGA 2 IN 1k:)
(1) For capacitor value C1, f is the desired lower cutoff frequency and RRXPGA1IN is the input resistance of RX_PGA1.
(2) For capacitor value C2, f is the desired lower cutoff frequency and RRXPGA2IN is the input resistance of RX_PGA2.
Figure 17. Complete Rx Signal Path (with Optional Band-Pass Filter)
DAC Block and DSP Path
The AFE032 contains a digital signal processing (DSP) path that receives incoming DAC samples delivered from
an external processor, conditions each sample, and delivers these samples to a 12-bit DAC. The device serial
interface is used to write directly to the DSP path when the DAC pin (pin 7) is driven high. Use the following
sequence to write samples to the DAC:
• Send a valid XCLK signal to the device (refer to the AFE032 Clock Requirements section for more details on
the XCLK signal).
• Set CS low.
• Wait 20 DAC_CLK cycles (refer to the AFE032 Clock Requirements section for more details on the
relationship between the XCLK frequency and DAC_CLK frequency).
• Set the DAC pin (pin 7) high to configure the device in DAC mode.
• Write a 12-bit word to DIN. (1) Note that the DAC register is left-justified.
• Set CS high to indicate that the sample is entered.
Refer to the DAC Mode section for more details on using the device in DAC mode.
The full-scale DAC output swing equals the DAC_NRF voltage level. Table Table 4 shows the ideal dc DAC
output voltage for a given input code.
Table 4. Ideal DAC Output
INPUT CODE (Hex)
(1)
IDEAL DAC OUTPUT VOLTAGE (V)
7FF
DAC_NRF bias voltage
001
[(DAC_NRF bias voltage) / (212 – 1)] + (DAC_NRF bias voltage) / 2
000
(DAC_NRF bias voltage) / 2
FFF
[(DAC_NRF bias voltage) / 2] – (DAC_NRF bias voltage) / (212 – 1)
800
0
The only exception to the 12-bit DAC sample length is when using a 16-bit envelope. See the SPI Envelope Exception Case section for
more details.
DAC_NRF, PA_NRF, and TX_RX_NRF Blocks
The DAC_NRF, PA_NRF, and TX_RX_NRF blocks create biasing points used internally to the device. Each
reference divides its respective power-supply voltage with a precision resistive voltage divider. PA_NRF provides
a PA_VS / 2 voltage used for the PA; TX_RX_NRF provides an AVDD / 2 voltage used for the Tx PGA, Tx filter,
Rx PGA1, Rx filter, and Rx PGA2; and DAC_NRF provides an AVDD / 4.7 voltage used for the DAC. Each NRF
block has its output brought out to an external pin that can be used for filtering and noise reduction. These
capacitors are optional, but are recommended for best performance.
22
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Zero-Crossing Detector Block
The device includes three zero-crossing detectors. Zero-crossing detectors can be used to synchronize
communications signals to the ac line or sources of noise. Typically, in single-phase applications, only a single
zero-crossing detector is used. In three-phase applications, two or three zero-crossing detectors can be used.
Figure 18 shows the AFE032 configured for non-isolated, zero-crossing detection.
+
AVDD
3.3 V
ZLLS410 or
Equivalent
330 kW
330 kW
AVDD
330 kW
ZC_IN
ZC_OUT
Zero-Crossing
120 VAC to 240 VAC
50 Hz to 60 Hz
ZLLS410 or
Equivalent
AGND
Inside the Device
Figure 18. Non-Isolated Zero-Crossing Detection Using the AFE032
120 VAC to 240 VAC
50 Hz to 60 Hz
Non-isolated zero-crossing waveforms are shown in Figure 19.
350
0
-350
ZC_OUT
3.3
0
0
50
100
Time (5 ms/div)
Figure 19. Non-Isolated, Zero-Crossing Waveforms
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
23
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Schottky diodes are recommended (see Figure 18) for maximum device protection from line transients. These
diodes limit the ZC_IN pins (pins 32, 38, and 39) to within the maximum rating of (AVDD + 0.4 V) and (AGND –
0.4 V). Some applications may require an isolated zero-crossing detection circuit. With a minimal amount of
components, the AFE032 can be configured for isolated zero-crossing detection, as shown in Figure 20.
+
AVDD
3.3 V
AVDD
ZC_IN
ZC_OUT
Zero-Crossing
120 VAC to 240 VAC
50 Hz to 60 Hz
AGND
Inside the Device
PS2505-1A Opto Isolator
or Equivalent
Figure 20. Isolated Zero-Crossing Detection Using the AFE032
120 VAC to 240 VAC
50 Hz to 60 Hz
Isolated zero-crossing waveforms are shown in Figure 21.
350
0
-350
ZC_OUT
3.3
0
0
50
100
Time (5 ms/div)
Figure 21. Isolated Zero-Crossing Waveforms
24
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
DIGITAL LOGIC INTERFACE
The primary functions of the AFE032 digital module are to:
• Provide an interface for an external DSP to configure the internal blocks of the AFE032.
• Provide a digital processing path that conditions samples coming from an external DSP.
• Transmit the conditioned samples to the internal 12-bit DAC.
To accomplish these functions, the device digital logic supports two modes of operation: SPI mode and DAC
mode.
In SPI mode, the device processes commands to either configure the internal analog and digital circuits or to
provide status to an external DSP. In DAC mode, an external DSP uses the SPI to provide DAC samples to the
device.
Descriptions of all the registers mentioned in this section can be found in the Register Map section.
AFE032 Clock Requirements
The device requires the following clocks: XCLK and SCLK.
XCLK is a free-running clock with a 50/50 duty cycle, frequency ranges from 10 MHz to 40 MHz, and less than
180 ps of RMS jitter. SCLK is an SPI clock used for the SPI interface with frequency ranges from 14 MHz to 30
MHz. This clock is active when CS is '0'.
The device contains two programmable clock dividers that can be used to generate the internal DAC clock
(referred to as DAC_CLK). This internal DAC clock determines the rate at which the internal device DAC updates
its analog output. The internal DAC clock is also used by the digital logic in the device (with the exception of the
SPI slave module that requires a separate SCLK signal). The REG_CLK_DIV register is programmed by the user
to control the internal DAC clock frequency. The internal DAC clock is created by two 4-bit clock dividers in
series. Each divider is a 4-bit decimal clock divider that can divide the frequency of the XCLK signal by an
integer between 1 and 16. Each clock divider produces an N+1 divided-down clock, where N is the programmed,
4-bit divide value. The XCLK frequency can be divided by a maximum value of 256. The first divider in the series
is controlled by the POST_CLK_DIV bits (bits 7 to 4 in the REG_CLK_DIV register) and the second divider is
controlled by the PRE_CLK_DIV bits (bits 3 to 0 in the REG_CLK_DIV register). If the application does not need
to divide XCLK by a value greater than 16, then POST_CLK_DIV is not programmed because these bits default
to '0'. For applications where XCLK must be divided down by a number greater than 16, both PRE_CLK_DIV and
POST_CLK_DIV are used to create the target divide-down value required to generate DAC_CLK. In sum, the
relationship between XCLK and DAC_CLK can be expressed as Equation 3:
XCLK = (POST_CLK_DIV + 1) (PRE_CLK_DIV + 1) (DAC_CLK)
(3)
Note that for proper device operation, DAC_CLK must always be slower than SCLK.
In DAC mode, an external processor (also referred to as the SPI master or external DSP) transmits DAC
samples to the device via the SPI at a rate of fS samples per second. fS may be less than or equal to DAC_CLK;
however, the external processor clock and the AFE032 XCLK must be generated from the same crystal.
Power-Up Sequence
A specific power-up sequence must be implemented to properly use the AFE032. The device internal blocks are
disabled if proper VDD levels are not maintained. The following sequence applies at power-up (note that the SD
pin must be held low throughout the entire power-up sequence):
• Power is applied to the device.
• When the supply connected to the AVDD1, AVDD2, and DVDD pins reaches a valid, 3-V dc voltage level, the
device digital logic comes out of reset.
• At this point, a valid XCLK signal is sent to the device for at least 65,536 cycles.
Every time power is applied to the device, in addition to the power-up sequence, a complete initialization
sequence must be followed before the user can transmit data with the power amplifier. The complete initialization
sequence must be followed also after a soft reset is performed (see the AFE032 Reset Options section for more
information on soft reset). The Initialization Sequence section provides more details. Similarly, perform a
sequence each time the device transitions from receiver mode (also referred to as RX mode) to transmitter mode
(also referred to as TX mode). The Power Amplifier Enable Sequence section provides more details for this Rx to
Tx mode transition sequence.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
25
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
SPI Mode
Holding the DAC pin low places the device in SPI mode. The following rules apply to the SPI slave operation
when the device is in SPI mode:
• Each SPI operation is 16 bits wide.
• The CS pin is set to '0' for each 16-bit SPI operation.
• The CS pin is set to '1' between consecutive SPI operations.
• A minimum of ten DAC_CLK cycles must be inserted after a write operation and a minimum of five DAC_CLK
cycles must be inserted after a read operation. During these cycles, the CS pin is set to '1'.
• The device DIN pin value is latched in during the SCLK rising edge.
• The device drives DOUT on the SCLK falling edge.
• DOUT assumes a high-impedance state when CS is set to '1'.
During an SPI operation in SPI mode, the following protocol is applied to the DIN pin by the SPI master:
• The first bit of the operation is the read and write (R/W) bit. An SPI read is specified when an R/W bit is '1'.
An SPI write is specified when an R/W bit is '0'.
• The next seven bits are the SPI address.
• The next eight bits are the SPI data.
Table 5 lists a complete example of the 16-bit codeword format.
Table 5. 16-Bit Codeword Format for an SPI Operation in SPI Mode
BIT NAME
LOCATION
(0 = LSB, 15 = MSB)
DATA0
0
LSB of SPI data
DATA1
1
SPI data
DATA2
2
SPI data
DATA3
3
SPI data
DATA4
4
SPI data
DATA5
5
SPI data
DATA6
6
SPI data
FUNCTION
DATA7
7
MSB of SPI data
ADDR0
8
LSB of register address bit
ADDR1
9
Register address bit
ADDR2
10
Register address bit
ADDR3
11
Register address bit
ADDR4
12
Register address bit
ADDR5
13
Register address bit
ADDR6
14
MSB of register address bit
R/W
15
Read or write: 0 = write, 1 = read
During an SPI operation, the following protocol is applied to the DOUT pin:
• If the current SPI operation from the master is a write operation, the AFE032 displays the previous operation
received from the master on DOUT.
• If the current SPI operation from the master is a read operation, the AFE032 displays the R/W bit of the
previous operation followed by the 7-bit address of the previous operation on DOUT. The remaining eight bits
that follow depend on whether the previous operation was a read or write operation.
– If a read request immediately follows a write operation, then the last eight bits are whatever was written to
the device on DIN by the SPI master.
– If a read request immediately follows a read operation, then the last eight bits are the contents of the
AFE032 address used in the previous read operation.
Note that two SPI operations are required for the device to transmit status bits over the SPI. The first operation
provides the AFE032 with the SPI register address to be read. The second operation transfers the data.
26
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
A minimum of ten DAC_CLK cycles must be inserted between consecutive write operations and a minimum of
five DAC_CLK cycles must be inserted between consecutive read operations.
DAC Mode
The device digital logic contains four digital processing blocks to condition incoming DAC samples delivered from
an external processor. The digital processing blocks in the device are referred to as the DSP path, as shown in
Figure 22.
Device DSP Path
Address
CS
Write Data
DIN
DOUT
Device Control
Register Bank
Read Data
SPI
Slave
Valid
Data
SCLK
ASYNCH
FIFO
Block 2
Block 1
Block 3
Clip and
Offset
Block 4
12-Bit
DAC
DAC_OUT
SCLK
Bypass
XCLK
Bypass
Bypass
Bypass
DAC_CLK
Clock Divider
Figure 22. AFE032 DSP Path
Each block in the DSP path can be enabled or disabled to accommodate for different application scenarios.
Processing DAC samples through the device can be broken down as follows:
• The device receives DAC samples (12 bits per sample) from an external DSP through the SPI at a rate of fS
samples per second.
• The device receives the 12-bit samples and processes them as real signed numbers. Thus, bit 11 is
processed as a sign bit. Therefore, the absolute value of each sample has 11 bits of resolution.
• The device extracts the DAC samples from the SPI and synchronizes them to DAC_CLK through the
ASYNCH FIFO.
NOTE
The only exception to the 12-bit DAC sample length is when using a 16-bit envelope. See
the SPI Envelope Exception Case section for more details.
When an external DSP is ready to send DAC samples to the device, the DAC_MODE pin is asserted. The device
digital logic reconfigures the SPI slave to run in a proprietary mode of operation in order to receive samples from
the external DSP. In other words, the SPI interface becomes a write-only serial interface so that the external
DSP can send DAC samples to the device. Each sample must be 12 bits wide.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
27
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
The device digital logic sends valid samples to the DAC as long as the external DSP asserts the DAC_MODE pin
and sends 12-bit samples to the device. Note that whenever DAC_MODE is not asserted, whichever values are
present in the output stage of the DSP path continue to be driven to the DAC. Note also that, by default, all
digital processing blocks in the device retain their states when DAC mode is deasserted (see the DSP Path State
Retention section for more details). Use the following sequence to write samples to the DAC:
1. Send a valid XCLK signal to the device (refer to the AFE032 Clock Requirements section for more details on
the XCLK signal).
2. Set CS low.
3. Wait for at least 20 DAC_CLK cycles.
4. Set DAC (pin 7) high. This setting places the device in DAC mode.
5. Write the first 12-bit word to DIN. Note that the DAC register is left-justified.
6. Set CS high to indicate that the sample is entered.
7. Wait for at least four SCLK cycles.
8. Set CS low.
9. Write the subsequent 12-bit word to DIN. Note that the DAC register is left-justified.
10. Set CS high for at least four SCLK cycles to indicate that the sample is entered.
11. Repeat the last three steps for each new DAC sample.
NOTE
The only exception to the 12-bit DAC sample length is when using a 16-bit envelope. See
the SPI Envelope Exception Case section for more details.
Appending 24 mid-range value samples at the end of every transmission of DAC samples is recommended.
These 24 samples provide a smooth transition of the entire transmit path (that is, DSP blocks, Tx PGA, and Tx
filter) to SPI mode. When the transmission of the last DAC sample ends (and the CS pin is set high), wait for at
least 20 DAC_CLK cycles before bringing the DAC pin (pin 7) low.
SPI Envelope Exception Case
Some external processors cannot create a 12-bit wide SPI transmission and output 16 bits. If this limitation is
encountered, the device supports a special mode where a 12-bit DAC sample can be sent over the SPI inside a
16-bit window. To use the AFE032 16-bit SPI envelope feature take into account the following points:
• Set the DAC SPI select bit (bit 0 of the REG_AFE032_CTRL register) to '1'.
• Wait for at least 20 DAC_CLK cycles after setting the DAC SPI select bit.
• Set the DAC pin (pin 7) high. This setting places the device in DAC mode.
• Drive the 12-bit DAC sample in the MSB position of the 16-bit SPI envelope.
• Provide 16 valid SCLK cycles in the SPI envelope.
The AFE032 SPI slave latches the first 12 bits and forwards them to the DSP path. The remaining four bits are
dropped. When operating the device with the 16-bit SPI envelope enabled, the SPI must be driven exactly as
described in this section or the device will not process the DAC samples successfully.
Digital Filtering
Blocks 1 and 2 of the DSP path provide digital filtering to the samples generated by the external processor.
This section provides recommendations for the coefficient values for filter block 1 and filter block 2 of the DSP
path. Three frequency bands are considered:
• CENELEC A band, comprised of frequencies between 3 kHz and 95 kHz.
• ARIB band, comprised of frequencies between 10 kHz and 450 kHz.
• FCC band, comprised of frequencies between 10 kHz and 490 kHz.
Note that the addresses of all registers mentioned in this section are given in the REGISTER MAP section.
Table 6 provides the recommended PRE_CLK_DIV and POST_CLK_DIV values of the REG_CLK_DIV register
for the case of a 37.5 MHz XCLK frequency.
28
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 6. Recommended Clock Divider Values for Different Frequency Bands and XCLK = 37.5 MHz
Frequency band
Clock divider value (decimal)
POST_CLK_DIV (Hex)
PRE_CLK_DIV (Hex)
CENELEC A
22
10
1
ARIB
7
0
6
FCC
7
0
6
Table 7 provides the recommended coefficient values (in hexadecimal form) for block 1.
Table 7. Recommended Coefficient Values for Block 1 of DSP Path
Register
CENELEC A
ARIB
FCC
REG_COEFF1_BLOCK_1_MS
Disable
CC
A3
REG_COEFF1_BLOCK_1_LS
Disable
40
E0
REG_COEFF2_BLOCK_1_MS
Disable
E4
D8
REG_COEFF2_BLOCK_1_LS
Disable
50
E0
REG_COEFF3_BLOCK_1_MS
Disable
40
40
REG_COEFF3_BLOCK_1_LS
Disable
00
00
REG_COEFF4_BLOCK_1_MS
Disable
78
7E
REG_COEFF4_BLOCK_1_LS
Disable
40
80
REG_COEFF5_BLOCK_1_MS
Disable
40
40
REG_COEFF5_BLOCK_1_LS
Disable
00
00
REG_COEFF6_BLOCK_1_MS
Disable
30
17
REG_COEFF6_BLOCK_1_LS
Disable
C0
A0
REG_COEFF7_BLOCK_1_MS
Disable
15
3E
REG_COEFF7_BLOCK_1_LS
Disable
A0
D0
Table 8 provides the recommended coefficient values (in hexadecimal form) for block 2.
Table 8. Recommended Coefficient Values for Block 2 of DSP Path
Register
CENELEC A
ARIB
FCC
REG_COEFF1_BLOCK_2_MS
10
F8
D4
REG_COEFF1_BLOCK_2_LS
40
30
00
REG_COEFF2_BLOCK_2_MS
00
00
00
REG_COEFF2_BLOCK_2_LS
00
00
00
REG_COEFF3_BLOCK_2_MS
0C
0C
0C
REG_COEFF3_BLOCK_2_LS
F0
B0
60
REG_COEFF4_BLOCK_2_MS
0C
0C
0C
REG_COEFF4_BLOCK_2_LS
F0
B0
60
REG_COEFF5_BLOCK_2_MS
00
00
00
REG_COEFF5_BLOCK_2_LS
00
00
00
REG_COEFF6_BLOCK_2_MS
06
C3
96
REG_COEFF6_BLOCK_2_LS
E0
80
20
REG_COEFF7_BLOCK_2_MS
D1
D0
CC
70
REG_COEFF7_BLOCK_2_LS
80
F0
REG_COEFF8_BLOCK_2_MS
0A
09
19
REG_COEFF8_BLOCK_2_LS
C0
20
A0
REG_COEFF9_BLOCK_2_MS
06
0D
30
REG_COEFF9_BLOCK_2_LS
00
C0
E0
REG_COEFF10_BLOCK_2_MS
0A
09
19
REG_COEFF10_BLOCK_2_LS
C0
20
A0
REG_COEFF11_BLOCK_2_MS
2D
60
3B
REG_COEFF11_BLOCK_2_LS
20
60
C0
REG_COEFF12_BLOCK_2_MS
69
6B
6E
REG_COEFF12_BLOCK_2_LS
60
90
80
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
29
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Figure 23 shows the transfer function of block 2 when the recommended coefficients for the CENELEC A band
are used.
1.2
CELENEC A Filter
FS = 400 kHz
Magnitude (abs(H))
1
Block 2
0.8
0.6
0.4
0.2
0
30
60
90
120
150
180
Frequency (kHz)
210
C012
Figure 23. Transfer Function of Block 2 - CENELEC A Band Coefficients According to Table 8
Figure 24 shows the transfer function of blocks 1 and 2 when the recommended coefficients for the ARIB band
are used.
1.2
Magnitude (abs(H))
1
0.8
0.6
ARIB Filter
FS = 1200 kHz
0.4
Block 2
0.2
Block 1
0
100
200
300
400
500
Frequency (kHz)
600
C011
Figure 24. Transfer Function of Blocks 1 and 2 - ARIB Band Coefficients According to Table 7 and
Table 8
Figure 25 shows the transfer function of blocks 1 and 2 when the recommended coefficients for the FCC band
are used.
1.2
Magnitude (abs(H))
1
0.8
0.6
FCC Filter
FS = 1200 kHz
0.4
Block 2
0.2
Block 1
0
100
200
300
400
500
Frequency (kHz)
600
C010
Figure 25. Transfer Function of Blocks 1 and 2 - FCC Band Coefficients According to Table 7 and Table 8
SPI Clock To DAC Clock Synchronization
The device receives DAC samples from the external DSP over the SPI (which operates using SCLK) and writes
these samples to the ASYNCH FIFO for internal synchronization (the ASYNCH FIFO and the rest of the DSP
path operate using the internally-generated DAC_CLK signal). The FIFO read controller pulls the samples out of
the ASYNCH FIFO at the rate determined by the DAC_CLK frequency (not the rate determined by fS).
30
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Refer to Figure 22 for the block diagram of the AFE032 DSP path. Bits 1 though 4 of the REG_AFE032_CTRL
register determine which blocks are included in the DSP path and which are bypassed. The default values of
these bits is '0' and all four blocks are included in the DSP path when the device is powered up.
Block 3 of the DSP path operates synchronously with DAC_CLK and interpolates (by a factor of four) the signals
coming from the ASYNCH FIFO. Such interpolation requires that samples stored in the ASYNCH FIFO be
extracted no faster than one time every four DAC_CLK cycles; such interpolation also imposes an upper bound
to fS. The external DSP must send samples to the device at a rate less than or equal to one-fourth the DAC_CLK
frequency [that is, fS ≤ (DAC_CLK / 4)].
Block 4 should be used to improve performance in two cases:
• When block 3 is included in the DSP path and fS is strictly less than one-fourth the DAC_CLK frequency [that
is, fS < (DAC_CLK / 4)].
• When block 3 is bypassed (not included in the DSP path) and fS is strictly less than the DAC_CLK frequency
(that is, fS < DAC_CLK).
For these two cases, block 4 should be used and its 32-bit parameter should be written to the REG_OFFSET0,
REG_OFFSET1, REG_OFFSET2, and REG_OFFSET3 registers. This section describes four typical scenarios
that can be found in most applications.
Block 3 and Block 4 Are Bypassed
If an external DSP transmits DAC samples to the device at a rate equal to the DAC_CLK frequency (that is, fS =
DAC_CLK), then both block 3 and block 4 should be bypassed. Write a '0' to bits 1 to 4 of the
REG_AFE032_CTRL register. A parameter for block 4 does not need to be calculated or written. Table 9 shows
examples of this scenario.
Table 9. Example Cases of Bypassed Blocks 3 and 4
fS
(kSPS)
XCLK
(MHz)
XCLK
DIVIDER
REG_CLK_DIV (Hex)
DAC_CLK
(MHz)
BLOCK 3
BLOCK 4
500
37.5
75
4E
0.5
Bypassed
Bypassed
800
19.2
24
27
0.8
Bypassed
Bypassed
Block 3 Is Included, Block 4 Is Bypassed
If an external DSP transmits DAC samples to the device at a rate equal to one-fourth the DAC_CLK frequency
[that is, fS = (DAC_CLK / 4)], then block 3 is included and block 4 is bypassed. Write a '0' to bits 1, 2, and 4 and
write a '1' to bit 3 of the REG_AFE032_CTRL register. A parameter for block 4 does not need to be calculated or
written. Table 10 shows examples of this scenario.
Table 10. Example Cases of Block 3 Included and Block 4 Bypassed
fS
(MSPS)
XCLK
(MHz)
XCLK
DIVIDER
REG_CLK_DIV (Hex)
DAC_CLK
(MHz)
BLOCK 3
BLOCK 4
1.2
19.2
4
03
4.8
Included
Bypassed
0.625
37.5
15
0E
2.5
Included
Bypassed
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
31
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Block 3 Is Bypassed, Block 4 Is Included
If an external DSP transmits DAC samples to the device at a rate close to but less than the DAC_CLK frequency
(that is, fS < DAC_CLK), then block 3 is bypassed and block 4 is included. Write a '0' to bits 1, 2, and 3 and write
a '1' to bit 4 of the REG_AFE032_CTRL register. In this case, the 32-bit parameter for block 4 must be calculated
and written. This mode of operation is recommended as long as the ratio between fS and DAC_CLK is greater
than 0.8 and less than 1 (that is, 0.8 DAC_CLK < fS < DAC_CLK). Table 11 shows examples of this scenario.
To
•
•
•
calculate the 32-bit parameter for block 4:
Calculate the ratio between fS and DAC_CLK. Ratio = fS / DAC_CLK.
Multiply the ratio by 4,294,967,296. Product = (ratio)(4,294,967,296).
The parameter for block 4 is equal to the integer part of the product found. Parameter = integer part of
product.
The value of the 32-bit parameter for block 4 must be written in hexadecimal form to the REG_OFFSET0,
REG_OFFSET1, REG_OFFSET2, and REG_OFFSET3 registers. The order should be such that the most
significant byte of the parameter is stored in REG_OFFSET0 and the least significant byte is stored in
REG_OFFSET3.
Table 11. Example Cases of Block 3 Bypassed and Block 4 Included
BLOCK 4
PARAMETER
(Hex)
fS
(MSPS)
XCLK
(MHz)
XCLK
DIVIDER
REG_CLK_
DIV (Hex)
DAC_CLK
(MHz)
BLOCK 3
BLOCK 4
1.2
37.5
28
1D
1.339
Bypassed
Included
E5604189
0.8
37.5
45
48
0.833
Bypassed
Included
F5C28F5C
Block 3 and Block 4 Are Included
If an external DSP transmits DAC samples to the device at a rate close to but less than one-fourth the DAC_CLK
frequency [that is, fS < (DAC_CLK / 4)], then both block 3 and block 4 are included. Write a '0' to bits 1 and 2 and
write a '1' to bits 3 and 4 of the REG_AFE032_CTRL register. In this case, the 32-bit parameter for block 4 must
be calculated and written. This mode of operation is recommended as long as the ratio between fS and
DAC_CLK is greater than 0.2 and less than 0.25 (that is, 0.2 DAC_CLK < fS < 0.25 DAC_CLK). Table 12 shows
examples of this scenario.
To
•
•
•
calculate the 32-bit parameter for block 4:
Calculate the ratio between fS and DAC_CLK. Ratio = fS / DAC_CLK.
Multiply the ratio by 17,179,869,184. Product = (ratio)(17,179,869,184).
The parameter for block 4 is equal to the integer part of the product found. Parameter = integer part of
product.
The value of the 32-bit parameter for block 4 must be written in hexadecimal form to the REG_OFFSET0,
REG_OFFSET1, REG_OFFSET2, and REG_OFFSET3 registers. The order should be such that the most
significant byte of the parameter is stored in REG_OFFSET0 and the least significant byte is stored in
REG_OFFSET3.
Table 12. Example Cases of Block 3 and Block 4 Included
32
fS
(MSPS)
XCLK
(MHz)
XCLK
DIVIDER
REG_CLK_
DIV (Hex)
DAC_CLK
(MHz)
BLOCK 3
BLOCK 4
BLOCK 4
PARAMETER
(Hex)
1
37.5
9
08
4.167
Included
Included
F5C28F5C
1
19.2
4
03
4.8
Included
Included
D5555555
0.4
22.5
14
0D
1.607
Included
Included
FEDCBA98
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
DSP Path State Retention
By default, blocks 1 through 4 of the DSP path retain their states in between DAC sample bursts (when DAC
mode is deasserted). This default implementation functions best for most applications provided that all DAC
sample bursts end with at least 24 samples of midrange values. These 24 samples provide a smooth transition to
SPI mode. The default implementation can be altered by changing the DSP_CFG bit of the REG_AUX_CTL
register (see the Register Map section).
DAC Sample Clipping and Bias
The device provides the ability to clip DAC samples at the last stage of digital processing. An additional offset
may be added to the clipped DAC sample at the user's discretion. The clipping circuit operates in the following
manner:
• Program the device with an 11-bit clip value on the REG_CLIP0 and REG_CLIP1 registers.
• Program the device with an 11-bit clip offset value on the REG_CLIP_OFFSET0 and REG_CLIP_OFFSET1
registers.
• The programmed clip and offset values are not signed.
• The device digital logic compares the 11-bit magnitude of the DAC sample from the DSP path to the clip
value.
• If the magnitude of the DAC sample is greater than the clip value, then the final DAC sample equals the clip
value minus the offset value.
• If the magnitude of the DAC sample is less than the clip value, then the final DAC sample is unchanged.
AFE032 Reset Options
The device has two main types of reset mechanisms available. These reset options are hardware invoked and
software invoked.
External Reset and Analog Shutdown Mode
The device can be disabled by asserting the external SD pin. Asserting the external SD pin causes the device
digital logic to reset and also causes the analog module to shut down. Asserting the external SD pin disables the
DAC clock and the entire device is disabled. Adhere to the following protocol when asserting the external SD pin:
• Assert the SD pin for at least 1 µs.
• Make sure that the device receives a valid XCLK clock before, during, and after the SD pin is asserted.
When the SD pin is deasserted, a valid XCLK signal must be sent to the device for at least 65,536 cycles. The
device must be reprogrammed because all control registers are now reset.
Software Reset Options
Two types of software resets can be applied to the device digital logic: soft reset and sticky reset. Soft reset and
sticky reset create a reset pulse that is eight DAC_CLK cycles wide for the internal logic. These two reset
commands are controlled by the REG_AFE032_CTL register. Sticky reset preserves all SPI register settings. In
order to properly use the sticky reset, the values of all other control bits in the REG_AFE032_CTL register must
be read and noted before asserting the sticky reset bit. Whatever is written to the REG_AFE032_CTL register is
latched when performing a sticky reset. A soft reset, on the other hand, brings all device digital circuits to their
default states.
After a soft reset or sticky reset is performed, a valid XCLK signal must be sent to the device for at least 65,536
cycles. The device must be reprogrammed because all control registers are now reset (with the exception of the
REG_AFE032_CTL register bits in the case of a sticky reset).
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
33
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
AFE032 Interrupts
The device contains three maskable interrupt signals: IFLAG_INT, TFLAG_INT, and DIG_ERR_INT. These
interrupt masks are set by default and can be changed by writing to the REG_FLAG_CTL register. The interrupt
masks are used to prevent any or all interrupt signals from commanding the active-low, open-drain interrupt pin
(INT). The REG_AFE_STATUS register contains the status of the three maskable interrupt signals; these signals
operate as follows:
• IFLAG_INT: This interrupt is asserted when the PA goes to current limit mode for at least 16,384 DAC_CLK
cycles. If the PA goes to current limit mode but then falls out of current limit mode before 16,384 DAC_CLK
cycles have elapsed, then the IFLAG_INT is not set.
• TFLAG_INT: This interrupt is asserted when the PA goes to overtemperature mode.
• DIG_ERR_INT: This interrupt is a logical OR of all of individual interrupt vectors located in the
REG_DIG_ERR register. See the Digital Interrupt Bits section and Table 26 for more detalis.
Note that reading the REG_AFE_STATUS register resets the IFLAG_INT and TFLAG_INT bits. Similarly, reading
the REG_DIG_ERR register resets all of its bits. Note that the DIG_ERR_INT bit is not reset until the
REG_DIG_ERR register is read.
Digital Interrupt Bits
The device can identify certain errors that may be caused because of improper programming or clocking. These
errors are: AFIFO overflow, SPI write address fail, SPI illegal access, and SPI address error.
An AFIFO overflow error occurs if the ASYNCH FIFO used to convert DAC samples from the SPI to the DAC
clock domain has overflowed. This error indicates that the external DSP is transmitting DAC samples at a rate
(fS) higher than the maximum capability of the device DSP path for the current configuration. Refer to the SPI
Clock To DAC Clock Synchronization section for details on the proper selection of fS and XCLK.
An SPI write address fail error occurs when a read-only register is attempted to be written to. An SPI illegal
access error occurs when a reserved SPI register is attempted to be written to.
An SPI address error occurs when an SPI register is attempted to be accessed incorrectly. This error is caused
by several reasons: if a reserved SPI register is attempted to be written to, if an SPI register is attempted to be
accessed with an incorrect address (that is, an address that does not exist in Table 13), or if a read-only register
is attempted to be written to.
Initialization Sequence
The following initialization sequence must be performed (in addition to the sequence described in the Power-Up
Sequence section) to ensure the device is ready for communication to the power line each time power is applied
to the device and each time after a soft reset is performed:
• Ensure the shutdown pin is low.
• Ensure a valid XCLK signal is present.
• Configure the device in SPI mode by taking the DAC pin low.
• Wait for at least 65,536 XCLK cycles.
• Enable the PA_NRF, TX_RX_NRF, and DAC_NRF blocks.
• Configure the two programmable clock dividers.
• Select the Tx filter band.
• Set the Enable assist bit (bit 7 in the REG_HPF/LPF_CFG register).
• Select which block in the digital path is used and which is bypassed.
• If block 4 is included, program the block 4 parameter of the DSP path.
• Set the Tx PGA, Rx PGA 1, and Rx PGA 2 gains.
• Enable the low-pass filter (LPF) and high-pass filter (HPF) according to the application requirements by
writing to the REG_DAC/HPF/LPF/PA_CTL register. Make sure to enable the filter bias (bit 5 of the
REG_DAC/HPF/LPF/PA_CTL register).
• Enable the DAC block by writing to register REG_DAC/HPF/LPF/PA_CTL (do not set the DAC pin high; just
enable the DAC block to ensure the block is ready when the device is configured for transmission).
• Wait for two seconds to ensure all voltage references and signal path capacitors reach a steady state.
34
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Power Amplifier Enable and Disable Sequences
Whether immediately after the initialization sequence or when transitioning from receiver mode to transmitter
mode, one of the PA enable sequences described in this section must be used each time the device initiates a
signal transmission on the power line via the power amplifier. The specific enable sequence used depends on
whether the DAC block is enabled at least 300 µs prior to the start of the PA enable sequence or not.
PA Enable Sequence for a DAC Already Enabled Case
Use the following sequence if the DAC has been enabled for at least 300 µs.
• Simultaneously set the PA IQ current control bits (bits 6 and 7) and the PA current limit bits (bits 4 and 5) of
the REG_PA_CURRENT_CFG register. The PA IQ current control bits must be set to '10' (that is, the 95 mA
option). The PA current limit bit settings depend on the application.
• Enable the Filter bias enable bit (bit 5) of the REG_DAC/HPF/LPF/PA_CTL register.
• Write '1' to the TX enable bit (bit 4), and '0' to the RX enable bit (bit 3) of the REG_RX/TX_CTL register.
• Wait for 50 µs.
• Write B4 (hex) to the REG_DAC/HPF/LPF/PA_CTRL register. (This setting enables the PA internal subregulation circuitry, maintains the LPF and filter bias, and keeps the DAC enabled while leaving the HPF and
PA output stage disabled.)
• Wait for 20 µs.
• Write BC (hex) to the REG_DAC/HPF/LPF/PA_CTRL register. (This setting enables the PA output stage
while keeping the PA internal sub-regulation circuitry, LPF, filter bias, and DAC enabled. The HPF remains
disabled.)
• Enable the ENPAIQN bit (bit 3) and the ENPAIQP bit (bit 2) of the REG_PA_CURRENT_CFG register.
• Enable the ENPCOMP bit (bit 7) and ENNCOMP bit (bit 6) of the REG_RX/TX_CTL register.
• Set the Tx PGA gain to the desired value.
• Wait for at least 20 DAC_CLK cycles.
• Configure the device in DAC mode by taking the DAC pin high.
• Write the desired samples to the DAC following the procedure outlined in the DAC Mode section.
PA Enable Sequence Starting from a DAC in Disabled State Case
Use the following sequence if the DAC is disabled or if it is enabled for less than 300 µs prior to the start of the
PA enable sequence:
• Simultaneously set the PA IQ current control bits (bits 6 and 7) and PA current limit bits (bits 4 and 5) of the
REG_PA_CURRENT_CFG register. The PA IQ current control bits must be set to '10' (that is, the 95 mA
option). The PA current limit bit settings depend on the application.
• Enable the DAC by writing '1' to the DAC enable bit (bit 2) and the Filter bias enable bit (bit 5) of the
REG_DAC/HPF/LPF/PA_CTL register.
• Write '1' to the TX enable bit (bit 4), and '0' to the RX enable bit (bit 3) of the REG_RX/TX_CTL register.
• Wait for 300 µs.
• Write B4 (hex) to the REG_DAC/HPF/LPF/PA_CTRL register. (This setting enables the PA internal subregulation circuitry, maintains the LPF and filter bias, and keeps the DAC enabled while leaving the HPF and
PA output stage disabled.)
• Wait for 20 µs.
• Write BC (hex) to the REG_DAC/HPF/LPF/PA_CTRL register. (This setting enables the PA output stage
while keeping the PA internal sub-regulation circuitry, LPF, filter bias, and DAC enabled. The HPF remains
disabled.)
• Enable the ENPAIQN bit (bit 3) and the ENPAIQP bit (bit 2) of the REG_PA_CURRENT_CFG register.
• Enable the ENPCOMP bit (bit 7) and ENNCOMP bit (bit 6) of the REG_RX/TX_CTL register.
• Set the Tx PGA gain to the desired value.
• Wait for at least 20 DAC_CLK cycles.
• Configure the device in DAC mode by taking the DAC pin high.
• Write the desired samples to the DAC following the procedure outlined in the DAC Mode section.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
35
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
PA Disable Sequence
Use the following sequence to disable the PA:
• Disable the PA output enable bit (bit 3) on the REG_DAC/HPF/LPF/PA_CTRL register.
• Disable the PA internal sub-regulation circuitry (bit 4) of the REG_DAC/HPF/LPF/PA_CTL register.
• Disable the ENPAIQN bit (bit 3) and the ENPAIQP bit (bit 2) of the REG_PA_CURRENT_CFG register.
• Disable the ENPCOMP bit (bit 7) and ENNCOMP bit (bit 6) of the REG_RX/TX_CTL register.
• Set the PA IQ current control bits (bits 6 and 7) of the REG_PA_CURRENT_CFG register to '00' (that is, the
55 mA option).
36
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
REGISTER MAP
The AFE032 data registers are listed in the memory map of Table 13. A description of each register is given in the Register Description section.
Table 13. Data Register Memory Map
REGISTER
ADDRESS
(Hex)
DEFAULT
VALUE (Hex)
BIT 7
BIT 6
REG_AFE032_CTL
00
00
Soft reset
REG_FLAG_CTL
01
E0
RESERVED
02
7F
IFLAG mask
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Sticky reset
Reserved
Bypass Block 4
Bypass Block 3
Bypass Block 2
Bypass Block 1
DAC SPI select
TFLAG mask
DIG_ERR
mask
HPF enable
Filter bias
enable
Reserved
REG_DAC/HPF/LPF/PA_CTL
03
00
REG_PA_CURRENT_CFG
04
00
REG_HPF/LPF_CFG
05
00
Enable Assist
REG_RX/TX_CTL
06
00
ENPCOMP
ENNCOMP
REG_RX_PGA_CFG
07
00
Zero-cross1
detect enable
Zero-cross2
detect enable
IFLAG_INT
TFLAG_INT
REG_VREF/ZEROX
08
00
RESERVED
09
18
REG_AFE_STATUS
0A
01
RESERVED
0B
00
RESERVED
0C
00
REG_DIG_ERROR
0D
00
Reserved
LPF enable
PA IQ current control
PA enable
PA current limit
LPF band select
PA output
enable
DAC enable
Reserved
Disable TLIM
ENPAIQN
ENPAIQP
ENPAICLN
ENPAICLP
Reserved
Reserved
Tx enable
Rx enable
Zero-cross3
detect enable
PA_NRF
enable
TX_RX_NRF
enable
Reserved
DIG_ERR_INT
RX_PGA1 gain
HPF band select
Reserved
TX_PGA gain
RX_PGA2 gain
Reserved
DAC_NRF
enable
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SPI write
address fail
AFIFO overflow
Die_ID
SPI illegal
access
SPI address
error
REG_ID
0E
00
REG_CLK_DIV
0F
03
Revision
REG_OFFSET_0
10
F5
Most significant byte of block 4 parameter
REG_OFFSET_1
11
C2
Second to MSB of block 4 parameter
REG_OFFSET_2
12
8F
Third to MSB of block 4 parameter
REG_OFFSET_3
13
5C
Least significant byte of block 4 parameter
REG_CLIP_0
14
FF
REG_CLIP_1
15
E0
REG_CLIP_OFFSET_0
16
00
REG_CLIP_OFFSET_1
17
00
REG_AUX_CTL
18
26
RESERVED
19 to 23
00
REG_COEFF1_BLOCK_2_MS
24
B9
REG_COEFF1_BLOCK_2_LS
25
D0
REG_COEFF2_BLOCK_2_MS
26
E8
REG_COEFF2_BLOCK_2_LS
27
60
DAC clock POST_CLK_DIV
Reserved
Reserved
DAC clock PRE_CLK_DIV
CLIP_MSB
CLIP_LSB
Reserved
CLIP_OFF_MSB
CLIP_OFF_LSB
Reserved
Reserved
Reserved
DSP_CFG
Reserved
Reserved
Bits 11:4 of coefficient 1 for filter block 2
Bits 3:0 of coefficient 1 for filter block 2
Reserved
Bits 11:4 of coefficient 2 for filter block 2
Bits 3:0 of coefficient 2 for filter block 2
Reserved
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
37
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 13. Data Register Memory Map (continued)
38
REGISTER
ADDRESS
(Hex)
DEFAULT
VALUE (Hex)
REG_COEFF3_BLOCK_2_MS
28
0F
REG_COEFF3_BLOCK_2_LS
29
00
REG_COEFF4_BLOCK_2_MS
2A
1D
REG_COEFF4_BLOCK_2_LS
2B
C0
REG_COEFF5_BLOCK_2_MS
2C
0F
REG_COEFF5_BLOCK_2_LS
2D
00
REG_COEFF6_BLOCK_2_MS
2E
99
REG_COEFF6_BLOCK_2_LS
2F
40
REG_COEFF7_BLOCK_2_MS
30
CA
REG_COEFF7_BLOCK_2_LS
31
10
REG_COEFF8_BLOCK_2_MS
32
1F
REG_COEFF8_BLOCK_2_LS
33
20
REG_COEFF9_BLOCK_2_MS
34
3B
REG_COEFF9_BLOCK_2_LS
35
10
REG_COEFF10_BLOCK_2_MS
36
1F
REG_COEFF10_BLOCK_2_LS
37
20
REG_COEFF11_BLOCK_2_MS
38
23
REG_COEFF11_BLOCK_2_LS
39
B0
REG_COEFF12_BLOCK_2_MS
3A
44
REG_COEFF12_BLOCK_2_LS
3B
20
REG_COEFF1_BLOCK_1_MS
3C
B9
REG_COEFF1_BLOCK_1_LS
3D
D0
REG_COEFF2_BLOCK_1_MS
3E
E8
REG_COEFF2_BLOCK_1_LS
3F
60
REG_COEFF3_BLOCK_1_MS
40
0F
REG_COEFF3_BLOCK_1_LS
41
00
REG_COEFF4_BLOCK_1_MS
42
1D
REG_COEFF4_BLOCK_1_LS
43
C0
REG_COEFF5_BLOCK_1_MS
44
0F
REG_COEFF5_BLOCK_1_LS
45
00
REG_COEFF6_BLOCK_1_MS
46
23
REG_COEFF6_BLOCK_1_LS
47
B0
REG_COEFF7_BLOCK_1_MS
48
44
REG_COEFF7_BLOCK_1_LS
49
20
REG_DAC_SAMPLE_MS
4A
00
REG_DAC_SAMPLE_LS
4B
00
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Bits 11:4 of coefficient 3 for filter block 2
Bits 3:0 of coefficient 3 for filter block 2
Reserved
Bits 11:4 of coefficient 4 for filter block 2
Bits 3:0 of coefficient 4 for filter block 2
Reserved
Bits 11:4 of coefficient 5 for filter block 2
Bits 3:0 of coefficient 5 for filter block 2
Reserved
Bits 11:4 of coefficient 6 for filter block 2
Bits 3:0 of coefficient 6 for filter block 2
Reserved
Bits 11:4 of coefficient 7 for filter block 2
Bits 3:0 of coefficient 7 for filter block 2
Reserved
Bits 11:4 of coefficient 8 for filter block 2
Bits 3:0 of coefficient 8 for filter block 2
Reserved
Bits 11:4 of coefficient 9 for filter block 2
Bits 3:0 of coefficient 9 for filter block 2
Reserved
Bits 11:4 of coefficient 10 for filter block 2
Bits 3:0 of coefficient 10 for filter block 2
Reserved
Bits 11:4 of coefficient 11 for filter block 2
Bits 3:0 of coefficient 11 for filter block 2
Reserved
Bits 11:4 of coefficient 12 for filter block 2
Bits 3:0 of coefficient 12 for filter block 2
Reserved
Bits 11:4 of coefficient 1 for filter block 1
Bits 3:0 of coefficient 1 for filter block 1
Reserved
Bits 11:4 of coefficient 2 for filter block 1
Bits 3:0 of coefficient 2 for filter block 1
Reserved
Bits 11:4 of coefficient 3 for filter block 1
Bits 3:0 of coefficient 3 for filter block 1
Reserved
Bits 11:4 of coefficient 4 for filter block 1
Bits 3:0 of coefficient 4 for filter block 1
Reserved
Bits 11:4 of coefficient 5 for filter block 1
Bits 3:0 of coefficient 5 for filter block 1
Reserved
Bits 11:4 of coefficient 6 for filter block 1
Bits 3:0 of coefficient 6 for filter block 1
Reserved
Bits 11:4 of coefficient 7 for filter block 1
Bits 3:0 of coefficient 7 for filter block 1
Reserved
Bits 11:4 of DAC sample fed from DSP path into DAC
Bits 3:0 of DAC sample fed from DSP path into DAC
Submit Documentation Feedback
Reserved
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Register Description
Table 14. REG_AFE032_CTL Register (Address = 00h)
7
6
5
Soft reset
Sticky reset
Reserved
R0/W
R0/W
R
4
3
2
1
0
Bypass Block 4 Bypass Block 3 Bypass Block 2 Bypass Block 1 DAC SPI select
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = read and write; R0/W = read '0' and write (these bits always reset to '0' after being written); R = read-only.
Bit 7
Soft reset
This bit creates a reset pulse to all AFE digital circuits and control registers. This bit is self resetting.
0 = Normal operation (default)
1 = Reset
Bit 6
Sticky reset
This bit resets all AFE digital circuits except the SPI registers. The SPI registers maintain all currently programmed
values. This bit is self resetting.
0 = Normal operation (default)
1 = Reset
Bit 5
Reserved
This bit is reserved.
Default = 0.
Bit 4
Bypass Block 4
This bit determines if block 4 is included in the signal path.
0 = Include block 4 (default)
1 = Bypass block 4
Bit 3
Bypass Block 3
This bit determines if block 3 is included in the signal path.
0 = Include block 3 (default)
1 = Bypass block 3
Bit 2
Bypass Block 2
This bit determines if block 2 is included in the signal path.
0 = Include block 2 (default)
1 = Bypass block 2
Bit 1
Bypass Block 1
This bit determines if block 1 is included in the signal path.
0 = Include block 1 (default)
1 = Bypass block 1
Bit 0
DAC SPI select
This bit sets the 12-bit DAC sample in either a 16-bit SCLK envelope or a 12-bit SCLK envelope.
0 = 12-bit DAC burst (default)
1 = 16-bit DAC burst
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
39
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 15. REG_FLAG_CTL Register (Address = 01h)
7
6
5
4
3
2
IFLAG mask
TFLAG mask
DIG_ERR
mask
Reserved
R/W
R/W
R/W
R
1
0
LEGEND: R/W = read and write; R = read-only.
Bit 7
IFLAG mask
Software asserts this bit to prevent the current-limit interrupt from commanding the INT external pin. The current
limit event still asserts the IFLAG_INT bit on the REG_AFE_STATUS register.
0 = Do not mask
1 = Mask IFLAG_INT (default)
Bit 6
TFLAG mask
Software asserts this bit to prevent the overtemperature interrupt from commanding the INT external pin. The
overtemperature event still asserts the TFLAG_INT bit on the REG_AFE_STATUS register.
0 = Do not mask
1 = Mask TFLAG_INT (default)
Bit 5
DIG_ERR mask
Software asserts this bit to prevent the digital error status bits from commanding the INT external pin. Any digital
errors can still be read in the REG_DIG_ERROR register.
0 = Do not mask
1 = Mask digital errors (default)
Bits[4:0]
Reserved
These bits are reserved.
Default = 0.
Table 16. RESERVED Register (Address = 02h)
7
6
5
4
3
2
1
0
Reserved
R
LEGEND: R = read-only.
This register is reserved. Default = 7Fh
40
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 17. REG_DAC/HPF/LPF/PA_CTRL Register (Address = 03h)
7
6
5
4
3
2
1
LPF enable
HPF enable
Filter bias
enable
PA enable
PA output
enable
DAC enable
Reserved
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
Disable TLIM
R/W
LEGEND: R/W = read and write.
Bit 7
LPF enable
This bit enables and disables the programmable analog low-pass filter (LPF).
0 = LPF disabled (default)
1 = LPF enabled
Bit 6
HPF enable
This bit enables and disables the programmable analog high-pass filter (HPF).
0 = HPF disabled (default)
1 = HPF enabled
Bit 5
Filter bias enable
This bit enables and disables the programmable LPF and HPF. For normal Rx or Tx operation, this bit remains
enabled. For power-down operation, this bit is disabled by placing the analog filters in low-power mode with high
output impedance.
0 = Disabled (default)
1 = Enable filter bias
Bit 4
PA enable
This bit enables and disables the internal sub-regulation circuitry of the power amplifier.
0 = Disabled (default)
1 = PA enabled
Bit 3
PA output enable
This bit enables the PA output stage. When enabled, the PA output stage functions normally with a low output
impedance capable of driving heavy loads. When disabled, the PA output stage is placed in a high-impedance
state.
0 = Disabled (default)
1 = PA output enabled
Bit 2
DAC enable
This bit enables and disables the DAC.
0 = DAC disabled (default)
1 = DAC enabled
Bit 1
Reserved
This bit is reserved.
Default = 0
Bit 0
Disable TLIM
This bit enables and disables the PA thermal shutdown circuitry. Warning: keeping the PA thermal shutdown
circuitry enabled to prevent potential permanent damage to the device is strongly recommended. See the Thermal
Overload section for more details.
0 = PA TLIM enabled (default)
1 = PA TLIM disabled
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
41
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 18. REG_PA_CURRENT_CFG Register (Address = 04h)
7
6
5
4
3
2
1
PA IQ current control
PA current limit
ENPAIQN
ENPAIQP
ENPAICLN
R/W
R/W
R/W
R/W
R/W
0
ENPAICLP
R/W
LEGEND: R/W = read and write.
Bits[7:6]
PA IQ current control
These bits control the PA programmable quiescent current.
00
01
10
11
Bits[5:4]
=>
=>
=>
=>
55
80
95
25
mA,
mA,
mA,
mA,
typ (default)
typ
typ
typ
PA current limit
These bits control the PA programmable current limit.
00
01
10
11
Bit 3
=>
=>
=>
=>
1.25 A, typ (default)
1.8 A, typ
2.5 A, typ
3.0 A, typ
ENPAIQN
This bit enables and disables the PA quiescent current negative bias circuitry.
0 = Disabled (default)
1 = Enabled
Bit 2
ENPAIQP
This bit enables and disables the PA quiescent current positive bias circuitry.
0 = Disabled (default)
1 = Enabled
Bit 1
ENPAICLN
This bit enables and disables the PA negative current limit circuitry.
0 = The PA negative current limit circuitry is enabled and protects the device (default)
1 = The PA negative current limit circuitry is disabled and the device is at risk of permanent damage if a current
overload event occurs
Bit 0
ENPAICLP
This bit enables and disables the PA positive current limit circuitry.
0 = The PA positive current limit circuitry is enabled and protects the device (default)
1 = The PA positive current limit circuitry is disabled and the device is at risk of permanent damage if a current
overload event occurs
42
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 19. REG_HPF/LPF_CFG Register (Address = 05h)
7
6
5
4
3
2
1
0
Enable assist
LPF band select
Reserved
HPF band select
Reserved
R/W
R/W
R/W
R/W
R
LEGEND: R/W = read and write; R = read only.
Bit 7
Enable assist
This bit must be asserted as part of the analog signal chain (Tx and Rx PGAs and filters) enabling process.
0 = Enable assist circuitry is not engaged (default)
1 = Enable assist circuitry is engaged (recommended for best performance)
Bits[6:4]
LPF band select
This bit selects the programmable analog LPF cutoff frequency.
000 = 95 kHz (default)
001 = 150 kHz
010 = 420 kHz
011 = 490 kHz
Bit 3
Reserved
This bit is reserved.
Default = 0
Bits[2:1]
HPF band select
This bit selects the programmable analog HPF cutoff frequency.
00 = 35 kHz (default)
01 = 150 kHz
Bit 0
Reserved
This bit is reserved.
Default = 0
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
43
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 20. REG_RX/TX_CTL Register (Address = 06h)
7
6
5
4
3
2
1
ENPCOMP
ENNCOMP
Reserved
TX enable
RX enable
TX_PGA gain
R/W
R/W
R/W
R/W
R/W
R/W
0
LEGEND: R/W = read and write.
Bit 7
ENPCOMP
This bit enables the PA positive start control.
0 = Disabled (default)
1 = Enabled
Bit 6
ENNCOMP
This bit enables the PA negative start control.
0 = Disabled (default)
1 = Enabled
Bit 5
Reserved
This bit is reserved.
Default = 0
Bit 4
TX enable
This bit enables and disables TX_PGA and configures the programmable filter for either Tx or Rx mode.
0 = Tx path disabled (default)
1 = Tx path enabled
Bit 3
RX enable
This bit enables and disables RX_PGA1 and RX_PGA2. This bit can either be left enabled or disabled during Tx
mode.
0 = Rx disabled (default)
1 = Rx enabled
Bits[2:0]
TX_PGA gain
These bits select the TX_PGA gain.
000 = 1.15 (default)
001 = 2.3
010 = 3.25
011 = 4.6
44
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 21. REG_RXPGA_CFG Register (Address = 07h)
7
6
5
4
3
2
1
0
RX_PGA1 gain
RX_PGA2 gain
Reserved
R/W
R/W
R/W
LEGEND: R/W = read and write.
Bits[7:4]
RX_PGA1 gain
These bits select the RX_PGA1 gain.
0000 = 0.125 (default)
0001 = 0.25
0010 = 0.5
0011 = 1
0100 = 2
0101 = 4
0110 = 8
0111 = 16
1000 = 32
Bits[3:1]
RX_PGA2 gain
These bits select the RX_PGA2 gain.
000 = 1 (default)
001 = 4
010 = 16
Bit 0
Reserved
This bit is reserved.
Default = 0
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
45
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 22. REG_VREF/ZEROX Register (Address = 08h)
7
6
5
4
3
2
1
0
Zero-cross1
detect enable
Zero-cross2
detect enable
Zero-cross3
detect enable
PA_NRF
enable
TX_RX_NRF
enable
DAC_NRF
enable
Reserved
R/W
R/W
R/W
R/W
R/W
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bit 7
Zero-cross1 detect enable
This bit enables and disables the zero-crossing 1 detector.
0 = Disabled (default)
1 = Enabled
Bit 6
Zero-cross2 detect enable
This bit enables and disables the zero-crossing 2 detector.
0 = Disabled (default)
1 = Enabled
Bit 5
Zero-cross3 detect enable
This bit enables and disables the zero-crossing 3 detector.
0 = Disabled (default)
1 = Enabled
Bit 4
PA_NRF enable
This bit enables and disables the PA noise-reducing filter (NRF) and internal reference bias generator. For normal
operation, this bit is enabled. This bit is disabled during operational conditions requiring maximum power savings.
The device cannot transmit when this bit is disabled.
0 = Disabled (default)
1 = Enabled
Bit 3
TX_RX_NRF enable
This bit enables and disables the Tx and Rx NRF and internal reference bias generator. For normal operation, this
bit is enabled. This bit is disabled during operational conditions requiring maximum power savings. The device
cannot transmit or receive when this bit is disabled.
0 = Disabled (default)
1 = Enabled
Bit 2
DAC_NRF enable
This bit enables and disables the DAC NRF and internal reference bias generator. For normal operation, this bit is
enabled. This bit is disabled during operational conditions requiring maximum power savings. The device cannot
transmit when this bit is disabled.
0 = Disabled (default)
1 = Enabled
Bits[1:0]
Reserved
These bits are reserved.
Default = 0
Table 23. RESERVED Register (Address = 09h)
7
6
5
4
3
2
1
0
Reserved
R
LEGEND: R = read-only.
This register is reserved. Default = 18h
46
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 24. REG_AFE_STATUS Register (Address = 0Ah)
7
6
5
4
3
2
1
IFLAG_INT
TFLAG_INT
Reserved
DIG_ERR_INT
Reserved
R0
R0
R0
R
R
0
LEGEND: R/W = read and write; R = read-only; R0 = read '0' (these bits reset to '0' after being read).
Bit 7
IFLAG_INT
This bit is set when the PA enters the current limit state for at least 16,384 DAC_CLK cycles. This interrupt is
cleared after being read.
0 = PA current limit not detected (default)
1 = PA current limit detected
Bit 6
TFLAG_INT
This bit is set when the PA enters the thermal limit state. This interrupt is cleared after being read.
0 = PA thermal limit not detected (default)
1 = PA thermal limit detected
Bit 5
Reserved
This bit is reserved.
Default = 0
Bit 4
DIG_ERR_INT
This bit is set when a digital error is detected. The REG_DIG_ERROR register must be read in order to clear this
interrupt.
0 = Digital errors not detected (default)
1 = Digital errors detected
Bits[3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 25. RESERVED Registers (Address = 0Bh to 0Ch)
7
6
5
4
3
2
1
0
Reserved
R
LEGEND: R = read-only.
These registers are reserved.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
47
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 26. REG_DIG_ERROR Register (Address = 0Dh)
7
6
5
4
3
2
1
0
Reserved
Reserved
AFIFO overflow
SPI write
address fail
SPI illegal
access
SPI address
error
Reserved
R0
R0
R0
R0
R0
R0
R
LEGEND: R = read-only; R0 = read '0' (these bits reset to '0' after being read).
This register is comprised of digital logic error detection bits. All bits are reset to '0' when read.
Bits[7:6]
Reserved
Reserved
Default = 0
Bit 5
AFIFO overflow
SPI and DAC ASYNCH FIFO overflow.
0 = Normal operation (default)
1 = Error detected
Bit 4
SPI write address fail
An error indicates that a read-only register was attempted to be written to.
0 = Normal operation (default)
1 = Error detected
Bit 3
SPI illegal access
An error indicates that a register reserved for factory testing and trimming was attempted to be written to.
0 = Normal operation (default)
1 = Error detected
Bit 2
SPI address error
An error indicates that either a nonexistent register, a reserved register, or a read-only register was attempted to be
written to.
0 = Normal operation (default)
1 = Error detected
Bits 1:0
Reserved
These bits are reserved.
Default = 0
Table 27. REG_ID Register (Address = 0Eh)
7
6
5
4
3
2
1
Die_ID
Revision
Reserved
R
R
R
0
LEGEND: R = read-only.
Bits[7:6]
Die_ID
These bits are the die identification.
Default = 0
Bits[5:3]
Revision
These bits are the revision indicator.
Default = 0
Bits[2:0]
Reserved
These bits are reserved.
Default = 0
48
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 28. REG_CLK_DIV Register (Address = 0Fh)
7
6
5
4
3
2
1
DAC clock POST_CLK_DIV
DAC clock PRE_CLK_DIV
R/W
R/W
0
LEGEND: R/W = read and write.
Bits[7:4]
DAC clock POST_CLK_DIV
Internal DAC clock divider offset.
These bits control the value of the second clock divider. DAC_CLK is related to XCLK by: XCLK = (PRE_CLK_DIV
+ 1) × (POST_CLK_DEV + 1) x DAC_CLK.
Default = 0
Bits[3:0]
DAC clock PRE_CLK_DIV
Internal DAC clock divider offset.
These bits control the value of the first clock divider. DAC_CLK is related to XCLK by: XCLK = (PRE_CLK_DIV + 1)
× (POST_CLK_DEV + 1) x DAC_CLK.
Default = 3h
Table 29. REG_OFFSET_0 Register (Address = 10h)
7
6
5
4
3
2
1
0
1
0
1
0
Most significant byte of block 4 parameter
R/W
LEGEND: R/W = read and write.
Bits[7:0]
Most significant byte of block 4 parameter
These bits are the MSB of the 32-bit parameter for block 4 of the DSP path.
Default = F5h
Table 30. REG_OFFSET_1 Register (Address = 11h)
7
6
5
4
3
2
Second to MSB of block 4 parameter
R/W
LEGEND: R/W = read and write.
Bits[7:0]
Second to MSB of block 4 parameter
These bits are second in line to the MSB of the block 4 parameter.
Default = C2h
Table 31. REG_OFFSET_2 Register (Address = 12h)
7
6
5
4
3
2
Third to MSB of block 4 parameter
R/W
LEGEND: R/W = read and write.
Bits[7:0]
Third to MSB of block 4 parameter
These bits are third in line to the MSB of the block 4 parameter.
Default = 8Fh
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
49
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 32. REG_OFFSET_3 Register (Address = 13h)
7
6
5
4
3
2
1
0
1
0
Least significant byte of block 4 parameter
R/W
LEGEND: R/W = read and write.
Bits[7:0]
Least significant byte of block 4 parameter
These bits are the LSB of the block 4 parameter.
Default = 5Ch
Table 33. REG_CLIP_0 Register (Address = 14h)
7
6
5
4
3
2
CLIP_MSB
R/W
LEGEND: R/W = read and write.
Bits[7:0]
CLIP_MSB
These bits are the MSB of the 11-bit clip value. Input samples to the DAC are clipped by this value.
These bits control DAC_CLIP[10:3].
Default = FFh
Table 34. REG_CLIP_1 Register (Address = 15h)
7
6
5
4
3
2
CLIP_LSB
Reserved
R/W
R0
1
0
LEGEND: R/W = read and write; R0 = read '0' (these bits reset to '0' after being read).
Bits[7:5]
CLIP_LSB
These bits are the LSB of the 11-bit clip value. Input samples to the DAC are clipped by this value.
These bits control DAC_CLIP[2:0].
Default = 07h
Bits[4:0]
Reserved
These bits are reserved.
Default = 0
Table 35. REG_CLIP_OFFSET_0 Register (Address = 16h)
7
6
5
4
3
2
1
0
CLIP_OFF_MSB
R/W
LEGEND: R/W = read and write.
Bits[7:0]
CLIP_OFF_MSB
These bits are the MSB of the 11-bit clip offset value. Clipped DAC samples have this offset subtracted from the
clipped value.
These bits control DAC_CLIP_OFF[10:3].
Default = 0
50
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 36. REG_CLIP_OFFSET_1 Register (Address = 17h)
7
6
5
4
3
2
1
CLIP_OFF_LSB
Reserved
R/W
R
0
LEGEND: R/W = read and write; R = read-only.
Bits[7:5]
CLIP_OFF_LSB
These bits are the LSB of the 11-bit clip offset value. Clipped DAC Samples have this offset subtracted from the
clipped value.
These bits control DAC_CLIP_OFF[2:0].
Default = 0
Bits[4:0]
Reserved
These bits are reserved.
Default = 0
Table 37. REG_AUX_CTL Register (Address = 18h)
7
6
5
Reserved
Reserved
DSP_CFG
4
3
Reserved
2
1
Reserved
0
R/W
R/W
R/W
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits[7:6]
Reserved
This bits are reserved.
Default = 0
Bit 5
DSP_CFG
This bit allows the state of the DSP blocks to be retained or to be forced to their reset values during SPI mode.
0 = Hold the state of the DSP path blocks when the device is in SPI mode (default)
1 = Reset the state of the DSP path when the device is in DAC mode
Bits[4:1]
Reserved
These bits are reserved.
Default = 3h
Bit 0
Reserved
This bit is reserved.
Default = 0
Table 38. RESERVED Registers (Address = 19h to 23h)
7
6
5
4
3
2
1
0
1
0
Reserved
R
LEGEND: R = read-only.
These registers are reserved.
Table 39. REG_COEFF1_BLOCK_2_MS Register (Address = 24h)
7
6
5
4
3
2
Bits 11:4 of coefficient 1 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 1 for filter block 2
These bits contain the eight most significant bits of coefficient 1 for filter block 2.
Default = B9h
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
51
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 40. REG_COEFF1_BLOCK_2_LS Register (Address = 25h)
7
6
5
4
3
2
Bits 3:0 of coefficient 1 for filter block 2
Reserved
R/W
R
1
0
1
0
1
0
1
0
1
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 1 for filter block 2
These bits contain the four least significant bits of coefficient 1 for filter block 2.
Default = Dh
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 41. REG_COEFF2_BLOCK_2_MS Register (Address = 26h)
7
6
5
4
3
2
Bits 11:4 of coefficient 2 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 2 for filter block 2
These bits contain the eight most significant bits of coefficient 2 for filter block 2.
Default = E8h
Table 42. REG_COEFF2_BLOCK_2_LS Register (Address = 27h)
7
6
5
4
3
2
Bits 3:0 of coefficient 2 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 2 for filter block 2
These bits contain the four least significant bits of coefficient 2 for filter block 2.
Default = 6h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 43. REG_COEFF3_BLOCK_2_MS Register (Address = 28h)
7
6
5
4
3
2
Bits 11:4 of coefficient 3 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 3 for filter block 2
These bits contain the eight most significant bits of coefficient 3 for filter block 2.
Default = 0Fh
Table 44. REG_COEFF3_BLOCK_2_LS Register (Address = 29h)
7
6
5
4
3
2
Bits 3:0 of coefficient 3 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
52
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
Bits [7:4]
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Bits 3:0 of coefficient 3 for filter block 2
These bits contain the four least significant bits of coefficient 3 for filter block 2.
Default = 0h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 45. REG_COEFF4_BLOCK_2_MS Register (Address = 2Ah)
7
6
5
4
3
2
1
0
1
0
1
0
1
0
Bits 11:4 of coefficient 4 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 4 for filter block 2
These bits contain the eight most significant bits of coefficient 4 for filter block 2.
Default = 1Dh
Table 46. REG_COEFF4_BLOCK_2_LS Register (Address = 2Bh)
7
6
5
4
3
2
Bits 3:0 of coefficient 4 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 4 for filter block 2
These bits contain the four least significant bits of coefficient 4 for filter block 2.
Default = Ch
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 47. REG_COEFF5_BLOCK_2_MS Register (Address = 2Ch)
7
6
5
4
3
2
Bits 11:4 of coefficient 5 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 5 for filter block 2
These bits contain the eight most significant bits of coefficient 5 for filter block 2.
Default = 0Fh
Table 48. REG_COEFF5_BLOCK_2_LS Register (Address = 2Dh)
7
6
5
4
3
2
Bits 3:0 of coefficient 5 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 5 for filter block 2
These bits contain the four least significant bits of coefficient 5 for filter block 2.
Default = 0h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
53
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 49. REG_COEFF6_BLOCK_2_MS Register (Address = 2Eh)
7
6
5
4
3
2
1
0
1
0
1
0
1
0
1
0
Bits 11:4 of coefficient 6 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 6 for filter block 2
These bits contain the eight most significant bits of coefficient 6 for filter block 2.
Default = 99h
Table 50. REG_COEFF6_BLOCK_2_LS Register (Address = 2Fh)
7
6
5
4
3
2
Bits 3:0 of coefficient 6 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 6 for filter block 2
These bits contain the four least significant bits of coefficient 6 for filter block 2.
Default = 4h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 51. REG_COEFF7_BLOCK_2_MS Register (Address = 30h)
7
6
5
4
3
2
Bits 11:4 of coefficient 7 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 7 for filter block 2
These bits contain the eight most significant bits of coefficient 7 for filter block 2.
Default = CAh
Table 52. REG_COEFF7_BLOCK_2_LS Register (Address = 31h)
7
6
5
4
3
2
Bits 3:0 of coefficient 7 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 7 for filter block 2
These bits contain the four least significant bits of coefficient 7 for filter block 2.
Default = 1h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 53. REG_COEFF8_BLOCK_2_MS Register (Address = 32h)
7
6
5
4
3
2
Bits 11:4 of coefficient 8 for filter block 2
R/W
LEGEND: R/W = read and write.
54
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
Bits [7:0]
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Bits 11:4 of coefficient 8 for filter block 2
These bits contain the eight most significant bits of coefficient 8 for filter block 2.
Default = 1Fh
Table 54. REG_COEFF8_BLOCK_2_LS Register (Address = 33h)
7
6
5
4
3
2
Bits 3:0 of coefficient 8 for filter block 2
Reserved
R/W
R
1
0
1
0
1
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 8 for filter block 2
These bits contain the four least significant bits of coefficient 8 for filter block 2.
Default = 2h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 55. REG_COEFF9_BLOCK_2_MS Register (Address = 34h)
7
6
5
4
3
2
Bits 11:4 of coefficient 9 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 9 for filter block 2
These bits contain the eight most significant bits of coefficient 9 for filter block 2.
Default = 3Bh
Table 56. REG_COEFF9_BLOCK_2_LS Register (Address = 35h)
7
6
5
4
3
2
Bits 3:0 of coefficient 9 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 9 for filter block 2
These bits contain the four least significant bits of coefficient 9 for filter block 2.
Default = 1h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 57. REG_COEFF10_BLOCK_2_MS Register (Address = 36h)
7
6
5
4
3
2
1
0
Bits 11:4 of coefficient 10 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 10 for filter block 2
These bits contain the eight most significant bits of coefficient 10 for filter block 2.
Default = 1Fh
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
55
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 58. REG_COEFF10_BLOCK_2_LS Register (Address = 337h)
7
6
5
4
3
2
1
Bits 3:0 of coefficient 10 for filter block 2
Reserved
R/W
R
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 10 for filter block 2
These bits contain the four least significant bits of coefficient 10 for filter block 2.
Default = 2h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 59. REG_COEFF11_BLOCK_2_MS Register (Address = 38h)
7
6
5
4
3
2
1
0
1
0
Bits 11:4 of coefficient 11 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 11 for filter block 2
These bits contain the eight most significant bits of coefficient 11 for filter block 2.
Default = 23h
Table 60. REG_COEFF11_BLOCK_2_LS Register (Address = 39h)
7
6
5
4
3
2
Bits 3:0 of coefficient 11 for filter block 2
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 11 for filter block 2
These bits contain the four least significant bits of coefficient 11 for filter block 2.
Default = Bh
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 61. REG_COEFF12_BLOCK_2_MS Register (Address = 3Ah)
7
6
5
4
3
2
1
0
Bits 11:4 of coefficient12 for filter block 2
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 12 for filter block 2
These bits contain the eight most significant bits of coefficient 12 for filter block 2.
Default = 44h
Table 62. REG_COEFF12_BLOCK_2_LS Register (Address = 3Bh)
7
6
5
4
3
2
1
Bits 3:0 of coefficient 12 for filter block 2
Reserved
R/W
R
0
LEGEND: R/W = read and write; R = read-only.
56
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
Bits [7:4]
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Bits 3:0 of coefficient 12 for filter block 2
These bits contain the four least significant bits of coefficient 12 for filter block 2.
Default = 2h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 63. REG_COEFF1_BLOCK_1_MS Register (Address = 3Ch)
7
6
5
4
3
2
1
0
1
0
1
0
1
0
Bits 11:4 of coefficient 1 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 1 for filter block 1
These bits contain the eight most significant bits of coefficient 1 for filter block 1.
Default = B9h
Table 64. REG_COEFF1_BLOCK_1_LS Register (Address = 3Dh)
7
6
5
4
3
2
Bits 3:0 of coefficient 1 for filter block 1
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 1 for filter block 1
These bits contain the four least significant bits of coefficient 1 for filter block 1.
Default = Dh
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 65. REG_COEFF2_BLOCK_1_MS Register (Address = 3Eh)
7
6
5
4
3
2
Bits 11:4 of coefficient 2 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 2 for filter block 1
These bits contain the eight most significant bits of coefficient 2 for filter block 1.
Default = E8h
Table 66. REG_COEFF2_BLOCK_1_LS Register (Address = 3Fh)
7
6
5
4
3
2
Bits 3:0 of coefficient 2 for filter block 1
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 2 for filter block 1
These bits contain the four least significant bits of coefficient 2 for filter block 1.
Default = 6h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
57
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 67. REG_COEFF3_BLOCK_1_MS Register (Address = 40h)
7
6
5
4
3
2
1
0
1
0
1
0
1
0
1
0
Bits 11:4 of coefficient 3 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 3 for filter block 1
These bits contain the eight most significant bits of coefficient 3 for filter block 1.
Default = 0Fh
Table 68. REG_COEFF3_BLOCK_1_LS Register (Address = 41h)
7
6
5
4
3
2
Bits 3:0 of coefficient 3 for filter block 1
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 3 for filter block 1
These bits contain the four least significant bits of coefficient 3 for filter block 1.
Default = 0h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 69. REG_COEFF4_BLOCK_1_MS Register (Address = 42h)
7
6
5
4
3
2
Bits 11:4 of coefficient 4 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 4 for filter block 1
These bits contain the eight most significant bits of coefficient 4 for filter block 1.
Default = 1Dh
Table 70. REG_COEFF4_BLOCK_1_LS Register (Address = 43h)
7
6
5
4
3
2
Bits 3:0 of coefficient 4 for filter block 1
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 4 for filter block 1
These bits contain the four least significant bits of coefficient 4 for filter block 1.
Default = Ch
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 71. REG_COEFF5_BLOCK_1_MS Register (Address = 44h)
7
6
5
4
3
2
Bits 11:4 of coefficient 5 for filter block 1
R/W
LEGEND: R/W = read and write.
58
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
Bits [7:0]
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Bits 11:4 of coefficient 5 for filter block 1
These bits contain the eight most significant bits of coefficient 5 for filter block 1.
Default = 0Fh
Table 72. REG_COEFF5_BLOCK_1_LS Register (Address = 45h)
7
6
5
4
3
2
Bits 3:0 of coefficient 5 for filter block 1
Reserved
R/W
R
1
0
1
0
1
0
1
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 5 for filter block 1
These bits contain the four least significant bits of coefficient for filter block 1.
Default = 0h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 73. REG_COEFF6_BLOCK_1_MS Register (Address = 46h)
7
6
5
4
3
2
Bits 11:4 of coefficient 6 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 6 for filter block 1
These bits contain the eight most significant bits of coefficient 6 for filter block 1.
Default = 23h
Table 74. REG_COEFF6_BLOCK_1_LS Register (Address = 47h)
7
6
5
4
3
2
Bits 3:0 of coefficient 6 for filter block 1
Reserved
R/W
R
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 6 for filter block 1
These bits contain the four least significant bits of coefficient 6 for filter block 1.
Default = Bh
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 75. REG_COEFF7_BLOCK_1_MS Register (Address = 48h)
7
6
5
4
3
2
Bits 11:4 of coefficient 7 for filter block 1
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of coefficient 7 for filter block 1
These bits contain the eight most significant bits of coefficient 7 for filter block 1.
Default = 44h
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
59
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Table 76. REG_COEFF7_BLOCK_1_LS Register (Address = 49h)
7
6
5
4
3
2
Bits 3:0 of coefficient 7 for filter block 1
Reserved
R/W
R
1
0
1
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of coefficient 7 for filter block 1
These bits contain the four least significant bits of coefficient 7 for filter block 1.
Default = 2h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
Table 77. REG_DAC_SAMPLE_MS Register (Address = 4Ah)
7
6
5
4
3
2
Bits 11:4 of DAC sample fed from DSP path into DAC
R/W
LEGEND: R/W = read and write.
Bits [7:0]
Bits 11:4 of DAC sample fed from DSP path into DAC
These bits contain the eight most significant bits of DAC sample fed from DSP path into DAC.
Default = 00h
Table 78. REG_DAC_SAMPLE_LS Register (Address = 4Bh)
7
6
5
4
3
2
1
Bits 3:0 of DAC sample fed from DSP path into DAC
Reserved
R/W
R
0
LEGEND: R/W = read and write; R = read-only.
Bits [7:4]
Bits 3:0 of DAC sample fed from DSP path into DAC
These bits contain the four least significant bits of DAC sample fed from DSP path into DAC.
Default = 0h
Bits [3:0]
Reserved
These bits are reserved.
Default = not applicable
60
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
POWER SUPPLIES
The device has two low-voltage analog power-supply pins and one low-voltage digital supply pin. Internally, the
two analog supply pins are connected to each other through back-to-back electrostatic discharge (ESD)
protection diodes. These pins must be connected to each other on the application printed circuit board (PCB).
Connecting the digital supply pin and the two analog supply pins together on the PCB is also recommended.
Both low-voltage analog ground pins are also connected internally through back-to-back ESD protection diodes.
These ground pins should also be connected to the digital ground pin on the PCB. Bypassing the low-voltage
power supplies with a parallel combination of a 10-μF and 100-nF capacitor is recommended. The PA block is
biased separately from a high-voltage, high-current supply.
Three PA power-supply pins and three PA ground pins are available to provide a path for the high currents
associated with driving the low impedance of the ac mains. Connecting the three PA supply pins together is
recommended. Placing a 47-μF to 100-μF bypass capacitor in parallel with a 100-nF capacitor as close as
possible to the device is also recommended. Care must be taken when routing the high-current ground lines on
the PCB to avoid creating voltage drops in the PCB ground that may vary with changes in load current.
The device has many options to enable or disable the functional blocks to allow for flexible power-savings
modes. Refer to the Electrical Characteristics: Power Supply table for power consumption in specific modes.
DAC, SD, INT, TSENSE, TX_FLAG, AND RX_FLAG PINS
This section discusses the DAC, SD, INT, TSENSE, TX_FLAG, and RX_FLAG pins.
DAC (Pin 7)
The DAC pin is used to configure the SPI to either read data to or write data from the command and data
registers, or to write data to the DAC register. Setting the DAC pin high allows access to the DAC register.
Setting the DAC pin low allows access to the command and data registers.
SD (Pin 8)
The shutdown pin (SD) can be used to shut down the entire device for maximum power savings. When the SD
pin is low, the device operates normally. When the SD pin is high, all circuit blocks within the device (including
the serial interface) are placed in the lowest-power operating modes. In this condition, the entire device draws
only 395 μA (typical) of current. All register contents at the time the device is placed in shutdown mode are
erased; when the device is re-enabled, the register contents are the device default values. Follow the protocol
described in the External Reset and Analog Shutdown Mode section when asserting the SD pin.
INT (Pin 9)
The interrupt pin (INT) is an active-low, open-drain output pin that can be used to signal the microprocessor of an
unusual operating condition that results from an anomaly on the power line. The INT pin can be triggered by
external circuit conditions and SPI operations, depending upon the REG_FLAG_CTL register settings. The
device can be programmed to issue an interrupt on current overload, thermal overload, and digital error
conditions. Refer to the AFE032 Interrupts section for more information.
When an interrupt is signaled (that is, INT goes low), the contents of the IFLAG_INT, TFLAG_INT, and
DIG_ERR_INT bits (bits 7, 6, and 4, respectively, in the REG_AFE_STATUS register) can be read to determine
the type of interrupt that occurred. The REG_FLAG_CTL register settings should be configured each time the
device is powered on.
Current overload and thermal overload conditions are explained in the Current Overload and Thermal Overload
sections. Digital error conditions are explained in the AFE032 Interrupts section.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
61
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Current Overload
The maximum output current allowed from the power amplifier (PA) can be programmed with the external RSET
resistor connected between PA_ISET (pin 26) and ground. The PA goes to current limit state if a fault condition
occurs, causing the PA to source or sink more current than its programmed limit value. IFLAG_INT (bit 7 in the
REG_AFE_STATUS register) is set to '1' if the PA goes to current limit state for more than 16,384 DAC_CLK
cycles.
Setting the IFLAG mask bit of the REG_FLAG_CTL register prevents a fault condition from commanding the
active-low, open-drain interrupt pin (INT). Note that the PA still goes to a current limit state to protect the device
and the IFLAG_INT bit is still set to '1'.
CAUTION
ENPAICLN and ENPAICLP (bits 1 and 0 of the REG_PA_CURRENT_CFG register,
respectively) allow the current limit protection circuitry to be enabled or disabled. By
default, the current limit protection circuitry is enabled and protects the device from
damage during current overload events only if the ENPAICLN and ENPAICLP bits
remain in their default states. Disabling these bits can potentially damage the device in
an current overload event.
Thermal Overload
The device contains internal PA thermal shutdown protection circuitry that automatically disables the PA output
stage if the junction temperature exceeds +165°C.
Note that the thermal shutdown protection circuitry only operates if a fault condition causes thermal overload
(that is, forces the junction temperature to exceed +165°C) and the Disable TLIM bit (bit 0 in the
REG_DAC/HPF/LPF/PA_CTL register) remains in the default state of '0'. The device thermal shutdown
protection circuitry allows the PA to resume normal operation only when the junction temperature falls below
+150°C. The TFLAG_INT bit remains set to '1' even after the device returns to normal operation. The
TFLAG_INT bit can be reset to '0' by performing a read operation on the REG_AFE_STATUS register.
Setting the TFLAG mask bit of the REG_FLAG_CTL register prevents a thermal overload event from
commanding the active-low, open-drain interrupt pin (INT). Note that the internal PA thermal shutdown protection
circuitry still disables the PA output stage automatically (provided that a thermal overload condition occurs and
the Disable TLIM bit is in set to '0') and the TFLAG_INT bit is still set to '1'.
62
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
TSENSE (Pin 35)
The TSENSE pin is internally connected to the anode of a temperature-sensing diode located within the PA
output stage. Figure 26 shows a remote junction temperature sensor circuit that can be used to measure the
device junction temperature. Measuring the device junction temperature is optional and is not required.
+3.3 V
0.1 mF
10 kW
(typ)
1
AFE032
V+
SCL
50 W
2
TSENSE
50 pF
3
D+
10 kW
(typ)
10 kW
(typ)
10 kW
(typ)
8
TMP411
SDA
7
SMBus
Controller
DALERT/THERM2
THERM
6
4
Overtemperature
Fault
GND
5
Figure 26. Interfacing the TMP411 to the AFE032
TX_FLAG (Pin 47)
The TX_FLAG pin is an open-drain output that indicates the readiness of the Tx signal path for transmission.
When the TX_FLAG pin is high, the transmit signal path is enabled and ready for transmission. When the
TX_FLAG pin is low, the transmit path is not ready for transmission.
RX_FLAG (Pin 48)
The RX_FLAG pin is an open-drain output that indicates the readiness of the Rx signal path for transmission.
When the RX_FLAG pin is high, the transmit signal path is enabled and ready for transmission. When the
RX_FLAG pin is low, the transmit path is not ready for transmission.
LINE-COUPLING CIRCUIT
The line-coupling circuit is one of the most critical circuits in a power-line modem. The line-coupling circuit has
two primary functions: first, to block the low-frequency signal of the mains (commonly 50 Hz or 60 Hz) from
damaging the low-voltage modem circuitry; second, to couple the modem signal to and from the ac mains. A
typical line-coupling circuit is shown in Figure 27.
Power
Amplifier
Low-Voltage
Capacitor
High-Voltage
Capacitor
+
N1
L
Phase
+
N2
Neutral
Figure 27. Simplified Line-Coupling Circuit
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
63
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
CIRCUIT PROTECTION
Power-line communications are often located in operating environments that are harsh for electrical components
connected to the ac line. Noise or surges from electrical anomalies (such as lightning, capacitor bank switching,
inductive switching, or other grid fault conditions) can damage high-performance integrated circuits if proper
protection is not provided. The AFE032, however, can survive even the harshest conditions by using a variety of
techniques to protect the device.
Layout the protection circuitry in order to dissipate as much of the electrical disturbance as possible with a multilayer approach using metal-oxide varistors (MOVs), transient voltage suppression diodes (TVSs), Schottky
diodes, and a Zener diode. These components dissipate the electrical disturbance before the anomaly reaches
the device. Figure 28 shows the recommended strategy for transient overvoltage protection.
PA
Power Supply
D1
Device
D2
Low-Voltage
Capacitor
High-Voltage
Capacitor
Phase
+
N1
+
N2
MOV
D3
Power
Amplifier
Neutral
TVS
Figure 28. Transient Overvoltage Protection for AFE032
Note that the high-voltage coupling capacitor must be able to withstand pulses up to the clamping protection
provided by the MOV. A metalized polypropylene capacitor, such as the 474MKP275KA from Illinois Capacitor™,
is rated for 50 Hz to 60 Hz and 250 VAC to 310 VAC, and can withstand 24 impulses of 2.5 kV.
64
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Table 79 and Table 80 list several recommended transient protection components.
Table 79. Recommended Transient Protection Devices (120 VAC, 60 Hz)
(1)
(2)
(3)
COMPONENT
DESCRIPTION
MANUFACTURER
MFR PART NO (OR EQUIVALENT)
D1
Zener diode
Diodes, Inc.
1SMB59xxB (1)
D2, D3
Schottky diode
Diodes, Inc.
B340A
TVS
Transient voltage suppressor
Littelfuse, Inc.
SMCJxxCA (2)
MOV
Varistor
Littelfuse, Inc.
TMOV20RP140E
HV capacitor
High-voltage capacitor
Illinois Capacitor, Inc
474MKP275KA (3)
Select the zener breakdown voltage at the lowest available rating beyond the normal power-supply operating range. For example,
1SMB5931B is suitable for systems where PA_VS = 15 V, whereas 1SMB5934B is suitable for systems where PA_VS = 20 V.
Select the TVS breakdown voltage at or slightly less than (0.5 × PA_VS). For example, SMCJ6.0CA is suitable for systems where
PA_VS = 15 V, whereas SMCJ8.0CA is suitable for systems where PA_VS = 20 V.
A common value for the high-voltage capacitor is 470 nF. Other values may be substituted depending on the appliction requirements.
Note that when making a substitution, for reliability, the capacitor must be selected from the same family or an equivalent family of
capacitors rated to withstand high-voltage surges on the power line.
Table 80. Recommended Transient Protection Devices (240 VAC, 50 Hz)
(1)
(2)
(3)
COMPONENT
DESCRIPTION
MANUFACTURER
MFR PART NO (OR EQUIVALENT)
D1
Zener diode
Diodes, Inc.
1SMB59xxB (1)
D2, D3
Schottky diode
Diodes, Inc.
B340A
TVS
Transient voltage suppressor
Littelfuse, Inc.
SMCJxxCA (2)
MOV
Varistor
Littelfuse, Inc.
TMOV20RP300E
HV capacitor
High-voltage capacitor
Illinois Capacitor, Inc
474MKP275KA (3)
Select the zener breakdown voltage at the lowest available rating beyond the normal power-supply operating range. For example,
1SMB5931B is suitable for systems where PA_VS = 15 V, whereas 1SMB5934B is suitable for systems where PA_VS = 20 V.
Select the TVS breakdown voltage at or slightly less than (0.5 × PA_VS). For example, SMCJ6.0CA is suitable for systems where
PA_VS = 15 V, whereas SMCJ8.0CA is suitable for systems where PA_VS = 20 V.
A common value for the high-voltage capacitor is 470 nF. Other values may be substituted depending on the appliction requirements.
Note that when making a substitution, for reliability, the capacitor must be selected from the same family or an equivalent family of
capacitors rated to withstand high-voltage surges on the power line.
THERMAL CONSIDERATIONS
In a typical power-line communications application, the device dissipates 2 W of power when transmitting to the
low-impedance ac line. This amount of power dissipation can increase the junction temperature, which in turn
can lead to a thermal overload that results in signal transmission interruptions if the PCB thermal design is not
implemented properly. Proper management of heat flow from the device as well as good PCB design and
construction are required to ensure proper device temperature, maximize performance, and extend device
operating life.
The device is assembled in a 7-mm x 7-mm, QFN-48 package. As Figure 29 shows, this QFN package has a
large-area exposed thermal pad on the underside that is used to conduct heat away from the device and to the
underlying PCB.
Figure 29. QFN Package with Large-Area Exposed Thermal Pad
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
65
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
Some heat is conducted from the silicon die surface through the plastic packaging material and is transferred to
the ambient environment. However, this route is not the primary thermal path for heat flow because plastic is a
relatively poor conductor of heat. Heat also flows across the silicon die surface to the bond pads, through the
wire bonds, to the package leads, and finally to the top layer of the PCB. While both of these paths for heat flow
are important, the majority (nearly 80%) of the heat flows downward, through the silicon die, to the thermallyconductive die-attach epoxy, and to the exposed thermal pad on the underside of the package (as shown in
Figure 30). Minimizing the thermal resistance of this downward path to the ambient environment maximizes the
life and performance of the device.
Less than 1%
~20%
~20%
~80%
Figure 30. Heat Flow in the QFN Package
The exposed thermal pad must be soldered to the PCB thermal pad. The thermal pad on the PCB must be the
same size as the exposed thermal pad on the underside of the QFN package. Refer to Application Report,
QFN/SON PCB Attachment (SLUA271A), for recommendations on attaching the thermal pad to the PCB.
Figure 31 illustrates the direction of heat spreading to the PCB from the device.
Device
Figure 31. Heat Spreading to PCB
The heat spreading to the PCB is maximized if the thermal path is uninterrupted. Best results are achieved if the
heat-spreading surfaces are filled with copper to the greatest extent possible, thus maximizing the percentage of
area covered on each layer. As an example, a thermally robust, multilayer PCB design can consist of four layers
with copper (Cu) coverage of 60% in the top layer, 85% and 90% in the inner layers (respectively), and 95% on
the bottom layer.
66
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
Increasing the number of layers in the PCB, using thicker copper, and increasing the PCB area are all factors
that improve the spread of heat. Figure 32 through Figure 34 show thermal resistance performance as a function
of each of these factors.
THERMAL RESISTANCE vs NUMBER OF PCB LAYERS
THERMAL RESISTANCE vs BOARD AREA
36
28
2
PCB Area = 3 in , 2 oz Cu
(Results are from thermal
simulations)
32
Four-Layer PCB, 2 oz Cu
(Results are from thermal
simulations)
26
Thermal Resistance (°C/W)
Thermal Resistance (°C/W)
34
30
28
26
24
22
24
22
20
18
16
14
12
20
10
1
2
3
4
5
6
7
8
4
2
6
8
10
12
14
2
Number of Layers
PCB Area (in )
Figure 32. Thermal Resistance as a Function of
the Number of Layers in the PCB
Figure 33. Thermal Resistance as a Function of
PCB Area
35
Four-Layer PCB, PCB
2
Area = 4.32 in , 2 oz Cu
(Results are from thermal
simulations)
Thermal Resistance (°C/W)
33
31
29
27
25
23
21
19
17
15
0.5
1
1.5
2
2.5
Cu Thickness (oz)
Figure 34. Thermal Resistance as a Function of Copper Thickness
For additional information on thermal PCB design using exposed thermal pad packages, refer to Application
Reports Analog Front-End Design for a Narrowband Power-Line Communications Modem Using the AFE031
(SBOA130) and PowerPAD™ Thermally-Enhanced Package (SLMA002E) (both available for download at
www.ti.com).
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
67
AFE032
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
www.ti.com
TYPICAL APPLICATION SCHEMATIC
A schematic for a typical application is provided in Figure 35.
18 V
3.3 V
100 k:
100 nF
10 nF
470 nF
10 PF
47 PF
1 P+
33 k:
33 k:
600 n+
100 k:
4.7 :
TMS320F28x
41
40
39
ZC_OUT1
ZC_IN1
42
PA_GND2
PA_VS2
43
PA_GND1
44
PA_OUT2
45
PA_VS1
46
PA_OUT1
3.3 V
47
RX_FLAG
DGND 1
48
TX_FLAG
DNC
GPIO
ZC_IN2
TVS
GPIO
38
37
100 :
2
AFE032
3
DIN
GPIO
4
DIGITAL
INTERFACE
(SPI)
5
GPIO
34
DNC
33
ZC_OUT3
32
DOUT
ZC_OUT2
35 TSENSE
SCLK
GPIO
1 nF
36
10 PF
DVDD
CONNECTION TO
POWER LINE
27 P+
ZC_IN3
31 DNC
3.3 V
CS
6
GPIO
30
DAC
GPIO
SD
GPIO
29
9
XCLK
GPIO
100 nF
8
INT
GPIO
100 nF
AVDD2
7
DSP
PATH
10
AGND2
POWER
AMPLIFIER
DAC
10 nF
33 k:
28
RX PGA1
TX_RX_NRF
3.3 V
AVDD1
27
11
TX PGA
RX PGA1 IN
FILTER
RX PGA2
26
10 PF
10 nF
PA ISET
1 k:
1 m+
AGND1
2.2 nF
25 NC
12
10 nF
23
24
DGND2
22
NC
21
20
RX_F_OUT
10 nF
19
RX_PGA2_IN
18
4.7 nF
PA NRF
17
PA IN
16
TX_F_OUT
15
DNC
DAC NRF
2.2 nF
14
DAC OUT
13
TX_PGA_IN
3.3 V
4.7 nF
100 k: 100 k:
RX_PGA2_OUT
ADC IN
330 :
Figure 35. Typical Application with Transformer Coupling
PACKAGING AND MECHANICALS
Complete mechanical drawings and packaging information are appended to the end of this data sheet.
68
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
AFE032
www.ti.com
SBOS669A – AUGUST 2013 – REVISED DECEMBER 2013
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (August 2013) to Revision A
Page
•
Changed document from product preview to production data .............................................................................................. 1
•
Changed first sub-bullet of second Features bullet .............................................................................................................. 1
•
Changed front page image ................................................................................................................................................... 1
•
Added Ordering Information and Absolute Maximum Ratings table ..................................................................................... 2
•
Added Thermal Information and Electrical Characteristics tables ........................................................................................ 3
•
Added SPI Timing Requirements table and Timing Diagrams section ............................................................................... 10
•
Added Pin Configuration section ........................................................................................................................................ 12
•
Added Functional Block Diagram section ........................................................................................................................... 14
•
Added Typical Characteristics section ................................................................................................................................ 15
•
Added Application Information section ............................................................................................................................... 17
•
Changed Series name in graph in Figure 23 ...................................................................................................................... 30
•
Changed Series names in graph legend in Figure 24 ........................................................................................................ 30
•
Changed Series names in graph legend in Figure 25 ........................................................................................................ 30
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: AFE032
69
PACKAGE OPTION ADDENDUM
www.ti.com
29-Dec-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
AFE032IRGZR
ACTIVE
VQFN
RGZ
48
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
AFE032
AFE032IRGZT
ACTIVE
VQFN
RGZ
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
AFE032
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
29-Dec-2013
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Dec-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
AFE032IRGZR
VQFN
RGZ
48
2500
330.0
16.4
7.3
7.3
1.5
12.0
16.0
Q2
AFE032IRGZT
VQFN
RGZ
48
250
180.0
16.4
7.3
7.3
1.5
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Dec-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
AFE032IRGZR
VQFN
RGZ
48
2500
367.0
367.0
38.0
AFE032IRGZT
VQFN
RGZ
48
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated