ZeroIC AWT6331 Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module TM Data Sheet - Rev 2.1 FEATURES • InGaP HBT Technology • High Efficiency: 39 % @ +28 dBm output • Zero Quiescent Current in Switch Mode • Internal Voltage Regulation • Optimized for a 50 Ω System • Low Profile Surface Mount Package: 1 mm • CDMA 1XRTT, 1xEV-DO Compliant • RoHS Compliant Package, 250 oC MSL-3 • Suitable for BC10 (806-824 MHz) Applications band APPLICATIONS • CDMA/EVDO Cell-band Wireless Handsets and Data Devices M27 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module PRODUCT DESCRIPTION The AWT6331 is a new product in the revolutionary ZeroIC™ PA family. The AWT6331 uses ANADIGICS’ exclusive InGaP-Plus™ technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWT6331 has a unique architecture with two RF inputs. One input drives the power amplifier while the other input drives an RF switch that bypasses the power amplifier, going directly to the RF output. The mode control logic selects the PA or the RF switch. In RF switch mode, current consumption is less than 10 A, reducing the average current consumption 70% more than a HELP2™ PA over the CDG profile. Its integrated voltage regulator eliminates the need for external components further reducing size and BOM cost. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 system. GND at slug (pad) VEN 10 GND 1 Bias Control VMODE 2 9 GND RFIN 3 8 RFOUT RFIN_Switch 4 7 VCC VBATT 5 6 VCC Figure 1: Block Diagram 10/2008 AWT6331 GND VEN 1 10 GND VMODE 2 9 GND RFIN_PA 3 8 RFOUT RFIN_Switch 4 7 VCC VBATT 5 6 VCC GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VEN 2 VMODE Mode Control 3 RFIN_PA RF Input to PA 4 RFIN_SWITCH 5 VBATT Battery Voltage 6 VCC Supply Voltage 7 VCC Supply Voltage 8 RFOUT RF Output 9 GND Ground 10 GND Ground PA Enable Voltage RF Input to Switch Data Sheet - Rev 2.1 10/2008 AWT6331 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC and VBATT) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Enable Voltage (VEN) 0 +3.5 V RF Input Power (PIN) to PA - +10 dBm RF Input Power (PIN) to Switch - +20 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +2.2 0 +2.4 - +3.1 +0.5 V PA "on", Switch "on" PA "shut down" Mode Control Voltage (VMODE) +2.2 0 +2.4 - +3.1 +0.5 V PA Mode Switch Mode RF Output Power (POUT) 27.5(1) 28.0 - dBm Case Temperature (TC) -30 - +85 °C CDMA The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1)For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.1 10/2008 3 AWT6331 Table 4: Electrical Specifications - CDMA Operation (IS-95 Modulation) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain Insertion Loss 25 - 28 0.7 30.5 1.5 dB POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -50 -70 -46.5 - dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -58.5 -70 -56 - dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V Isolation 32 40 - dB RFOUT to RFIN_SWITCH, VMODE = +2.4 V, PA "on" Power-Added Efficiency (1) 36 39 - % POUT = +28 dBm, VMODE = +2.4 V Enable Current - <0.1 0.25 mA through VEN pin, VEN = +2.4 V Mode Control Current - <0.01 0.1 mA through VMODE pin, VMODE = +2.4 V - <10 15 Leakage Current A - <10 18 Noise in Receive Band - -135 -133 Harmonics 2fo 3fo, 4fo - -40 -45 -30 -30 dBc Input Impedance - - 2:1 VSWR Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure VCC = +4.2 V, VEN = 0 V, VMODE = 0 V or +2.4 V VCC = +4.2 V, VEN = +2.4 V, VMODE = 0 V, Switch Mode dBm/Hz 869 MHz to 894 MHz CW Measurement - - -65 dBc POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Applies over all operating conditions Notes: (1) PAE and ACP limit applies at 836.5 MHz (IS-95 modulation). 4 COMMENTS Data Sheet - Rev 2.1 10/2008 AWT6331 APPLICATION INFORMATION Power Modes The power amplifier may be placed in either a Low Power mode or a High Power mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Power Control table lists the recommended modes of operation for various applications. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VEN and VMODE voltages. Table 5: Power Control POUT LEVELS POWER MODE VEN VMODE CDMA - Switch Bypass -* Low +2.4 V 0V Shutdown -* Low 0V +2.4 V CDMA - PA All High +2.4 V +2.4 V - Shutdown 0V 0V APPLICATION Shutdown *Dependent upon typical output power from Transceiver and phone design. VENABLE VMODE 1 VENABLE GND 2 VMODE GND 3 RFIN_PA 4 RFIN_SWITCH 5 VBATT C1 2.2 µF C2 0.01 F RFIN_PA RFIN_SWITCH VBATT GND at slug 10 9 RFOUT 8 VCC 7 VCC 6 GND at slug C6 68 pF RFOUT VCC C3 330 pF C4 0.01 µF C5 2.2 µF Figure 3: Application Circuit Data Sheet - Rev 2.1 10/2008 5 AWT6331 PACKAGE OUTLINE Figure 4: M27 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module 6331R LLLLNN BBBBCC Figure 5: Branding Specification 6 Data Sheet - Rev 2.1 10/2008 AWT6331 COMPONENT PACKAGING Pin 1 Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" Data Sheet - Rev 2.1 10/2008 7 AWT6331 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6331RM27Q7 -30 °C to +85 °C RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module AWT6331RM27P9 -30 °C to +85 °C RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.1 10/2008