HDSP-078x, HDSP-079x, HDSP-088x, HDSP-098x Glass/Ceramic Numeric and Hexadecimal Displays for Industrial Applications Data Sheet Description Features These standard solid state displays have a 7.4 mm (0.29 inch) dot matrix character and an on-board IC with data memory latch/decoder and LED drivers in a glass/ ceramic package. • Three character options Numeric, hexadecimal, over range • Three colors; High Efficiency Red, Yellow, High Performance Green • 4 x 7 dot matrix character • Two high efficiency red options Low power, high brightness • Performance guaranteed over temperature • High temperature stabilized • Memory latch/decoder/driver TTL compatible • Categorized for luminous intensity The hermetic HDSP-078x,-079x/‑088x displays utilize a solder glass frit seal. The HDSP-098X displays utilize an epoxy glass-to-ceramic seal. The numeric devices decode positive BCD logic into characters “0‑9,” a “–” sign, decimal point, and a test pattern. The hexadecimal devices decode positive BCD logic into 16 characters, “0-9, A-F.” An input is provided on the hexadecimal devices to blank the display (all LEDS off) without losing the contents of the memory. The over range device displays “±1” and right hand decimal point and is typically driven via external switching transistors. Devices Part Number HDSP- Color Description 0781 High-Efficiency Red Numeric, Right Hand DP 0782 Low Power Numeric, Left Hand DP 0783 Over Range ±1 0784 Hexadecimal 0791 High-Efficiency Red Numeric, Right Hand DP 0792 High Brightness Numeric, Left Hand DP 0794 Hexadecimal 0881 Yellow Numeric, Right Hand DP 0883 Over Range ±1 0884 Hexadecimal 0981 High-Performance Numeric, Right Hand DP 0983 Green Over Range ±1 0984 Hexadecimal Front View A B C D A B D A C D A C D Package Dimensions 7.4 (0.29) FRONT VIEW A FRONT VIEW B FRONT VIEW D 10.2 MAX. (0.400) 10.2 MAX. (0.400) 10.2 MAX. (0.400) 1.5 (0.06) 1.5 (0.06) 13.5 5.6 (0.53) (0.22) 7.4 (0.29) 5.6 (0.22) 5° 3.0 (0.12) 4.8 (0.19) 6 7 3.6 (0.14) COLOR CODE(3) LUMINOUS INTENSITY CATEGORY YYWW SYYWW DATE CODE PIN 1 KEY 3 2 1 FUNCTION HEXADECIMAL 1 Input 2 Input 2 2 Input 4 Input 4 3 Input 8 Input 8 4 Decimal Point Blanking Control 5 6 Latch Enable Ground Latch Enable Ground 7 VCC VCC 8 Input 1 Input 1 NOTES: 1. DIMENSIONS IN MILLIMETERS AND (INCHES). 2. UNLESS OTHERWISE SPECIFIED, THE TOLERANCE ON ALL DIMENSIONS IS ± 0.38 mm (± 0.015 INCH). 3. DIGIT CENTER LINE IS ± 0.25 mm (± 0.01 INCH) FROM PACKAGE CENTER LINE. 4. COLOR CODE FOR HDSP-088X/-098X SERIES. 1.5 (0.06) SEATING PLANE 15.2 (0.600) 0.3 ± 0.08 TYP. (0.012 ± 0.003) 1.3 TYP. (0.050) 3.4 (0.135) 0.5 ± 0.08 TYP. (0.020 ± 0.003) 2.5 ± 0.13 TYP. (0.100 ± 0.005) 2.8 (0.11) NUMERIC 3.8 (0.15) SEATING PLANE 4.3 (0.17) PIN END VIEW 0-10° COUNTRY CODE 4 4.8 (0.19) SIDE VIEW HDSP XXXX 13.5 (0.53) 5° 4.8 (0.19) 8 XZ 10.2 (0.400) 1.5 (0.06) 5° REAR VIEW 5 13.5 (0.53) 7.4 (0.29) tSETUP tHOLD DATA INPUT (LOW LEVEL DATA) 1.5 V TRUTH TABLE 1.5 V BCD DATA[1] DATA INPUT (HIGH LEVEL DATA) 1.5 V 1.5 V tTLH ENABLE INPUT 1.5 V 1.5 V 10% 90% tW Figure 1. Timing diagram. VCC ENABLE 7 5 LOGIC 8 1 2 3 X1 X2 X4 X8 4 DP INPUT DP(2) LATCH MEMORY MATRIX DECODER X8 X4 X2 L L L L L L L H L L H L L L H H L H L L L H L H L H H L L H H H L L L H L L H H L H L H L H H (BLANK) H H L L (BLANK) H H L H •••• H H H L (BLANK) H H H H (BLANK) DECIMAL PT.[2] BLANKING[3] BLANKING(3) CONTROL 4 GROUND 6 Figure 2. Block diagram. LED MATRIX DRIVER LED MATRIX NUMERIC H ENABLE[1] DP X1 ON OFF LOAD DATA LATCH DATA DISPLAY–ON DISPLAY–OFF HEXADECIMAL VDP = L VDP = H VE = L VE = H VB = L VB = H NOTES: 1. H = LOGIC HIGH; L = LOGIC LOW. WITH THE ENABLE INPUT AT LOGIC HIGH, CHANGES IN BCD INPUT LOGIC LEVELS HAVE NO EFFECT UPON DISPLAY MEMORY, DISPLAYED CHARACTER, OR DP. 2. THE DECIMAL POINT INPUT, DP, PERTAINS ONLY TO THE NUMERIC DISPLAYS. 3. THE BLANKING CONTROL INPUT, B, PERTAINS ONLY TO THE HEXADECIMAL DISPLAYS. BLANKING INPUT HAS NO EFFECT UPON DISPLAY MEMORY. Absolute Maximum Ratings Description Symbol Min. Max. Unit Storage Temperature, Ambient HDSP-078x/-079x/-088x TS -65 +125 °C HDSP-098x -55 +100 Operating Temperature, Ambient[1] TA -55 +100 Supply Voltage[2] VCC -0.5 +7.0 V Voltage Applied to Input Logic, dp and Enable Pins VI, VDP, VE -0.5 VCC V Voltage Applied to Blanking Input[2] VR -0.5 VCC V Soldering Temperature [1.59 mm (0.063 inch) Below Body] Solder Dipping, max 5 seconds Wave Soldering, max. 3 seconds 260 250 °C °C Recommended Operating Conditions Description Symbol Min. Nom. Max. Unit Supply Voltage[2] VCC 4.5 5.0 5.5 V Operating Temperature, Ambient[1] TA -55 +100 °C Enable Pulse Width tW 100 nsec Time Data Must Be Held Before Positive Transition of Enable Line tSETUP 50 nsec Time Data Must Be Held After Positive Transition of Enable Line tHOLD 50 nsec Enable Pulse Rise Time tTLH 1.0 msec Optical Characterstics at TA = 25°C, VCC = 5.0 V Device Description Symbol Min. Typ. Max. Unit HDSP-078x Series Luminous Intensity per LED (Digit Average)[3,4] IV 65 140 µcd Peak Wavelength lPEAK 635 nm Dominant Wavelength[5] ld 626 nm HDSP-079x Series Luminous Intensity per LED (Digit Average)[3,4] IV 260 620 µcd Peak Wavelength lPEAK 635 nm Dominant Wavelength[5] ld 626 nm HDSP-088x Series Luminous Intensity per LED (Digit Average)[3,4] lV 215 490 µcd Peak Wavelength lPEAK 583 nm Dominant Wavelength[5,6] ld 585 nm HDSP-098x Series Luminous Intensity per LED (Digit Average)[3,4] IV 298 1100 µcd Peak Wavelength lPEAK 568 nm Dominant Wavelength ld 574 nm Notes: 1. The nominal thermal resistance of a display mounted in a socket that is soldered onto a printed circuit board is RqJA = 50°C/W/device. The device package thermal resistance is RqJ-PIN = 15°C/W/device. The thermal resistance device pin-to-ambient through the PC board should not exceed 35°C/ W/device for operation up to TA = +100°C. 2. Voltage values are with respect to device ground, pin 6. 3. These displays are categorized for luminous intensity with the intensity category designated by a letter code located on the back of the display package. Case temperature of the device immediately prior to the light measurement is equal to 25°C. Electrical/Optical Characteristics TA = –55°C to +100°C Description Symbol Test Conditions Min. Typ.[7] HDSP-078x Series ICC 78 105 HDSP-079x/-088x/-098x Series VCC = 5.5 V Characters “5.” or “B” displayed 120 175 HDSP-078x Series PT 573 390 HDSP-079x/-088x/-098x Series VCC = 5.5 V Characters “5.” or “B” displayed 690 963 Logic, Enable and Blanking Low-Level Input Voltage VIL VCC = 4.5 V 0.8 V Logic, Enable High-Level Input Voltage VIH 2.0 V Blanking High-Voltage; Display Blanked VBH 2.3 V Logic and Enable Low-Level Input Current IIL VCC = 5.5 V –1.6 mA Blanking Low-Level Input Current IBL VIL = 0.4 V –10 µA Logic, Enable and Blanking High-Level Input Current IIH VCC = 5.5 V VIH = 2.4 V +40 µA Weight 1.0 gm 5 x 10-8 cc/sec Supply Current Power Dissipation Leak Rate Notes: 4. The luminous intensity at a specific operating ambient temperature, Iv(TA), may be approximated from the following exponential equation: Iv(TA) = Iv(25°C) e[k(TA-25°C)]. Device K HDSP-078 Series –0.0131/°C HDSP-079x Series HDSP-088x Series –0.0112/°C HDSP-098x Series –0.0104/°C Max. Unit mA mW 5. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 6. The HDSP-088X and HDSP-098X series devices are categorized as to dominant wavelength with the category designated by a number on the back of the display package. 7. All typical values at VCC = 5.0 V and TA = 25°C. Operational Considerations Electrical These devices use a modified 4 x 7 dot matrix of light emitting diodes to display decimal/hexadecimal numeric information. The high efficiency red and yellow displays use GaAsP/GaP LEDs and the high performance green displays use GaP/GaP LEDs. The LEDs are driven by constant current drivers, BCD information is accepted by the display memory when the enable line is at logic low and the data is latched when the enable is at logic high. Using the enable pulse width and data setup and hold times listed in the Recommended Operating Conditions allows data to be clocked into an array of displays at a 6.7 MHz rate. The decimal point input is active low true and this data is latched into the display memory in the same fashion as the BCD data. The decimal point LED is driven by the on-board IC. The blanking control input on the hexadecimal displays blanks (turns off ) the displayed information without disturbing the contents of display memory. The display is blanked at a minimum threshold level of 2.0 volts. When blanked, the display standby power is nominally 250 mW at TA = 25°C. The ESD susceptibility of the IC devices is Class A of MILSTD-883 or Class 2 of DOD-STD-1686 and DOD-HDBK263. Mechanical Preconditioning These displays are hermetically sealed for use in environments that require a high reliability device. These displays are designed and tested to meet a helium leak rate of 5 x 10‑8 cc/sec. These displays are 100% preconditioned by 24 hour storage at 125°C, at 100°C for the HDSP-098x Series. These displays may be mounted by soldering directly to a printed circuit board or insertion into a socket. The lead-to-lead pin spacing is 2.54 mm (0.100 inch) and the lead row spacing is 15.24 mm (0.600 inch). These displays may be end stacked with 2.54 mm (0.100 inch) spacing between outside pins of adjacent displays. Sockets such as Augat 324-AG2D (3 digits) or Augat 508-AG8D (one digit, right angle mounting) may be used. These display devices are designed to provide an optimum ON/OFF contrast when placed behind an appropriate contrast enhancement filter. For further information on contrast enhancement, see Application Note 1015, Contrast Enhancement for LED Displays. The primary thermal path for power dissipation is through the device leads. Therefore, to insure reliable operation up to an ambient temperature of +100°C, it is important to maintain a base-to-ambient thermal resistance of less than 35°C watt/device as measured on top of display pin 3. Contrast Enhancement Over Range Display The over range devices display “±1” and decimal point. The character height and package configuration are the same as the numeric and hexadecimal devices. Character selection is obtained via external switching transistors and current limiting resistors. For further information on soldering and post solder cleaning, see Application Note 1027, Soldering LED Components. Absolute Maximum Ratings Description Symbol Storage Temperature, Ambient TS –65 +125 °C Operating Temperature, Ambient TA –55 +100 °C Forward Current, Each LED IF 10 mA Reverse Voltage, Each LED VR 5 V Min Max Unit Package Dimensions FRONT VIEW C 10.2 MAX. (0.400) 8 7 6 PIN 5 1.5 (0.06) 7.4 (0.29) 4.8 (0.19) 4.8 (0.19) 5 1.9 (0.075) 1 13.5 (0.53) FUNCTION 1 Plus 2 Numeral One 3 4 Numeral One DP 5 Open 6 Open 7 VCC 8 Minus/Plus Pin Character 1 2,3 + 1 X – 0 X 1 X 1 Decimal Point X X Blank 0 0 3.3 (0.13) 2 3 4 Notes: 0: Line switching transistor in Figure 7 cutoff. 1: Line switching transistor in Figure 7 saturated. X: ‘don’t care.’ NOTE: DIMENSIONS IN MILLIMETERS AND (INCHES). #7 VCC = 5.0 V NUMERAL ONE MINUS PLUS PLUS d.p. #3 #2 R1 #4 R2 #8 R1 #1 R3 R3 Figure 3. Typical driving circuit. Luminous Intensity per LED (Digit Average) at TA = 25°C Device Test Conditions Min. Typ. Units HDSP-0783 IF = 2.8 mA 65 140 µcd IF = 8 mA 620 µcd HDSP-0883 IF = 8 mA 215 490 µcd HDSP-0983 IF = 8 mA 298 1100 µcd Recommended Operating Conditions VCC = 5.0 V Forward Current Resistor Value Device Per LED, mA R1 R2 R3 HDSP-0783 Low Power 2.8 1300 200 300 High Brightness 8 360 47 68 HDSP-0883 8 360 36 56 HDSP-0983 8 360 30 43 4 X X X 1 0 8 1 1 X X 0 Electrical Characteristics TA = –55°C to +100°C Device Description Symbol Test Conditions Min. Typ. Max. Unit HDSP-0783 Power Dissipation (All LEDs Illuminated) PT 72 mW IF = 8 mA 224 282 Forward Voltage per LED VF IF = 2.8 mA 1.6 IF = 8 mA 1.75 2.2 HDSP-0883 Power Dissipation (All LEDs Illuminated) PT IF = 8 mA 237 282 mW Forward Voltage per LED VF 1.90 2.2 V HDSP-0983 Power Dissipation (All LEDs Illuminated) PT IF = 8 mA 243 282 mW Forward Voltage per LED VF 1.85 2.2 V Intensity Bin Limits for HDSP-078x Series Bin Category Min. (mcd) Max. (mcd) A B C D E F G 0.065 0.085 0.114 0.165 0.260 0.403 0.625 0.102 0.138 0.200 0.300 0.488 0.756 1.172 Intensity Bin Limits for HDSP-079x Series Bin Category Min. (mcd) Max. (mcd) E F G H 0.260 0.403 0.625 0.969 0.488 0.756 1.172 1.820 Intensity Bin Limits for HDSP-088x Series Bin Category Min. (mcd) Max. (mcd) A B C D E F 0.22 0.28 0.38 0.55 0.82 1.27 0.34 0.46 0.66 0.99 1.54 2.39 Intensity Bin Limits for HDSP-098x Series Bin Category Min. (mcd) Max. (mcd) C D E F G 0.30 0.43 0.65 0.97 1.45 0.52 0.79 1.18 1.76 2.63 IF = 2.8 mA Condition Luminous Intensity per LED. VDD @ 5.0 V Condition Luminous Intensity per LED. VDD @ 5.0 V Color Bin Limits (Dominant Wavelength) Intensity Range (nm) Color Bin Min. Max. Yellow 1 581.50 585.00 2 584.00 587.50 3 586.50 590.00 Green 1 570.00 574.00 2 573.00 577.00 3 576.00 580.00 Note: Bin categories are established for classification of products. Products may not be available in all bin categories. Please consult your local Avago Technologies representative. Condition Luminous Intensity per LED. VDD @ 5.0 V Condition Luminous Intensity per LED. VDD @ 5.0 V For product information and a complete list of distributors, please go to our website: V www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved. Obsoletes 5989-3188EN AV02-1334EN - June 6, 2008