S/MOT/SV969300E/A/01/10/2003 INVERSEURS DE SENS DE ROTATION MOTOR REVERSER Entraxe 47,5mm /4,7,5mm mounting page 1 /5GB SV969300E 3x400VAC 4KW two legs model Le relais SV969300 est étudié pour démarrer et inverser le sens de rotation de moteurs triphasés asynchrones , avec la commutation de 2 phases uniquement ( 4 commutateurs : 2 legs) . Le calibre des thyristors est de 50AR MS (75A sur demande) , ce qui permet de contrôler un moteur avec un courant nominal de 8 à 10ARMS soit 4kWatts sous 400VAC ( 7,5kW sur demande avec les calibres 75A) , en tenant compte des courants de démarrage et d'inversion. Ces produits sont réalisés avec des composants haute immunité , sans relais REED ( tout électronique) , avec toutes les protections : RC , VDR,... mais aussi intervérouillage , temporisation entre chaque inversion,... Ces relais sont équipés de thyristors 1600V. Boitier IP20 IP20 housing The relay SV969300 is designed for controlling and inverting the direction of a three-phase motors without direct third leg ( two legs). The maximum current of semiconductors is 50 Amps. rms (75A on request), which allows a motor with a current rating of 8 up to 10 Amps.rms (or approximately 4 kW under 400 V (7,5kW on request )), taking the starting and reversing current into account. These products are designed with very high immunity components , without REED switches (only composed of solid state components) , with all protections : RC , VDR ,..... temporisation ,........., and 1600Volt peak voltage components. 82,7 Dimensions / Dimensions: M4 19 56,5 76 M3,5 23 47,6 58,4 5,3 19 92 100 3x 400VAC Circuit équivalent/Equivalent circuit : Internal block diagram : 1L1 0V -A2/B2 12-30VDC + B1 - A2/B2 3L2 celduc France Reverse Control logic 5L3 24-500VAC RC -VDR protection +A1 8,5A AC53a (EN60947-1) With suitable heatsink See instruction sheet R F +A1 +B1 - A2/B2 1L1 +A1 5L3 +B1 Reverse Forward EN60947-1 Forward 3L2 1L1 3L2 5L3 2T1 4T2 6T3 Insulation (photocouplers) Solid State Motor Reverser SV969300 2T1 4T2 6T3 M3~ Proud to serve you All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis. 2T1 4T2 6T3 celduc r e l a i s S/MOT/SV969300E/A/01/10/2003 page 2 / 5 F/GB Synoptique interne / Internal diagram for two leg models : Forward Reverse LED Controls Common A 2 /B2 Reverse Insu lation Switch RC network B1 + Forward lation Switch RC network Mains or load 2T1 ~ Load or mains 3L2 ~ Mains or load 4T2 ~ Load or mains 5L3 ~ Mains or load 6T3 ~ Load or mains VDR Control lock Insu 1L1 ~ VDR A1 + Input circuit Insu Insu lation Switch lation RC network Switch RC network VDR L3-T3 depending of models VDR Control Développé conformément aux normes / Designed in compliance with standards: ->EN60947-4-2 (V.D.E. 0660 part 109, I.E.C. 158-2) ->EN60947-1 & A11 ->EN60950 (V.D.E. 0805-> office equipment) (Pending approval) ->U.L. 508 (Pending approval) ->c.U.L (Pending approval) Plage de tension de commande / Control voltage range Plage de courant de commande / Control current range Tension de non fonctionnement/ Release voltage LED de visualisation / Display LED Uc Ic Ur 12-30VDC 15-25mADC 6VDC Yes Yes 30V no output fixed 70ms protection en cas de cdes simultanées / protection against simultaneous controls tension inverse maxi / Maximum reverse voltage Signal de sortie / Output signal temporisation inversion / Reversing time Urv Caractéristiques d'entrée-sortie (à 20°C) / Input-output characteristics (at 20°C) Isolement entrée-sortie/Input-output isolation @500m Isolement sortie-semelle/Output-case isolation @500m Tension assignée isolement/rated impulse voltage Caractéristiques générales / General characteristics Poids/Weight Plage de température de stockage / Storage temperature range Plage de température de fonctionnement/Operating temperature range Ui Ui Uimp 3300 3000 4000 130g -40 / +100 -40 / +100 Unit VRMS VRMS V Unit g °C °C celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SV969300E/A/01/10/2003 Sortie/ Output page 3 / 5 F/GB Tension nominale/ Standard mains voltage Plage de tension de fonctionnement / Mains voltage range tension crête non répétitive/ Non-repetitive maximum peak voltage Courant AC-53 maxi/ Max. nom. current (AC53a=AC3) @40°C Puissance moteur/ 3 pole power motor ( 3x400VAC) Chute directe / Max Direct voltage drop (@Ie) Courant crête non répétitif/ Non repetitive overload current (@ 1 cycle of 10ms) I2t value/ Melting limit (choice of fuse) @10ms Courant minimal de charge / Minimum load current facteur de puissance/ Power factor (@ Ie) Temps d'ouverture et de temporisation/ Turn on time-reversing time(@50Hz) Temps d'ouverture/ Turn off time (@50Hz) Courant de fuite /Maximum leakage current (@Ue/50Hz) dv/dt / Max off state voltage rise Fréquence de réseau / Operating frequency range 400 VAC 24-520VAC 1600V 8,5A ( see motor reverser selection) 4kW/5,5hp 1,4VRMS ITSM 550A I2t Imin Pf ton/trv toff Ilk dv/dt f 1500 A2s 100 mA 0 up to 1 20ms / 100ms 10ms 5 mARMS 500V/µs 25 up to 440Hz 4KV direct at output, 4KV with a clamp at input no turn on or damage 2KV in common mode, 1KV in differential mode (Input & output) no turn on or damage 10V/m E.M.C. Max conducted immunity level Test accord. to I.E.C.1000-4-4 (bursts) Max conducted immunity level Test acc. to I.E.C.1000-4-5 (el. shocks) Max radiated immunity level Test accord. to I.E.C.1000-4-3 Max electrostatic disch. immunity level Test accord. to I.E.C.1000-4-2 Max conducted emission level (0,8<Pf<1) Test according to EN55011 Max radiated emission level Test accord. to EN55011 @Ie Base/junction thermal resistance Rthjc Ambient/junction thermal resistance Rthja (relay mounted vertically) Weight Characteristics given at 25°C unless otherwise specified Ue Un Up Ie Pn Ud no turn on or damage 8KV in the air / 4KV touching no turn on or damage The conducted noise made by SSR depends on the wiring configuration and the load type. Test methods recommended by European E.M.C. standards giving results far from reality, we have chosen to advise the right filter suited for the customer's use: Refer to EMC chapter <30dBµV from 30 up to 230MHz ; <37dBµV from 230 up to 1000MHz Misc. 0,5K/W (1 leg) 5K/W 130g Thin layer of thermal grease 91 Mounting of a relay on a heatsink 40 Template r e l a i s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SV969300E/A/01/10/2003 Caractéristiques thermiques / Thermal curves : page 4 / 5 F/GB 30 30 1,2K/W = WF121100 Total wasted power (W) 25 25 20 20 15 15 sans dissipateur/ without heatsink 10 10 5 5 0 0 2 4 6 8 10 RMS load current (A) 12 0 Surge current Itsm (A peak) = f(t) 0 10 20 30 40 50 60 70 80 90 100 Ambient temperature (°C) for models with Itsm =550A 600 Itsm (Apeak) No repetitive Itsm (Apeak)=f(t) without voltage reapplied 400 200 0 0,01 Repetitive Itsm (Apeak)=f(t) with voltage reapplied for initial Tj =70°C 0,1 1 t (s) 10 Courant de surcharge non repetitif :ITSM / Non repetitive surge peak on-state current : ITSM REVERSERS + HEATSINK SELECTION IN COMPLIANCE WITH EN60947-4-2 Heatsink Relays with Ferraz fuse Overload Relays without heatsink ambient =40°C type relay type heatsink heatsink =80°C SSR SELECTION motors soft-staters for a permanent current Motor power In motor 0,75 kW 1,1 kW 1,5 kW 2,2 kW 3 kW 4 kW 14x51 size / max. rating Klöckner-Moeller am 8A/500V am 8A/500V am 12A/500V am 12A/500V am 12A/500V am 12A/500V Z00-2.4 Z00-6 Z00-6 Z00-6 Z00-10 Z00-10 two legs (@ 400V) two legs models 50A with integrated DIN RAIL adaptor ambient =40°C 2A 2,6A 3,5A 5A 6,6A 8,5A SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 none none none WF121000 WF121000 WF121000 SW960330 SW960330 SW960330 SW961230 SW961230 SW961230 For motor > 4kW consult us : we have some solutions celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SV969300E/A/01/10/2003 page 5 / 5 F/GB 03/94 NOTE D'APPLICATION : UTILISATION DU RELAIS STATIQUE SV969300 POUR L'INVERSION DE SENS DE ROTATION D'UN MOTEUR ASYNCHRONE MONOPHASE A CONDENSATEUR DE DEPHASAGE APPLICATION NOTE : USING A SV969300 RELAY FOR REVERSING AN ASYNCHRONOUS SINGLE PHASE MOTOR WORKING WITH A PHASE SHIFTING CAPACITOR ALIMENTATION MONOPHASE / Main voltage L N Reverse Forward 1L1 3L2 12-30VDC celduc France 5L3 24-500VAC 8,5A AC53a (EN60947-1) With suitable heatsink See instruction sheet 3L2 SV969300 2T1 2T1 4T2 4T2 R 1L1 5L3 Solid State Motor Reverser F +A1 +B1 -A2/B2 EN60947-1 Note : Le relais SV969300 développé initialement pour inverser le sens de rotation des moteurs asynchrones triphasés peut aussi être utilisé pour l'inversion de moteurs monophasés . Ce relais possède 4 voies de puissance , une temporisation à l'inversion et un verrouillage en cas de commande simultanée . Pour des quantités importantes , en utilisation monophasée , le produit peut être simplifié car seulement 2 voies sur 4 sont utilisées . 6T3 6T3 C Note : The SV969300 relay which has been initially developped in order to reverse three phase asynchronous motors , can be used for reversing single phase motors . This relay has 4 power switches , a reversing temporization and a lock in case of simultaneous controls . If you need a big quantity for a single phase use , please contact us , because we are able to simplify the product as only 2 switches among 4 are used . M celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19