S/MOT/SW960330/A/16/03/2000 INVERSEURS DE SENS DE ROTATION MOTOR REVERSER ( Ready to use) page 1 /5 F/GB SW960330 Le relais SW960330 est étudié pour démarrer et inverser le sens de rotation de moteurs triphasés asynchrones , avec la commutation de 2 phases uniquement ( 4 commutateurs : 2 legs) . Le produit directement montable sur rail DIN avec un calibre des thyristors de 50ARMS , permet de contrôler un moteur avec un courant nominal de 4,5ARMS soit 1,5kWatts sous 400VAC , en tenant compte des courants de démarrage et d'inversion. Ces produits sont réalisés avec des composants haute immunité , sans relais REED ( tout électronique) , avec toutes les protections : RC , VDR,... mais aussi intervérouillage , temporisation entre chaque inversion,... Ces relais sont équipés de thyristors 1600V. 3x400VAC 1,5KW Boitier IP20 IP20 housing 72 100 The relay SW960330 is designed for controlling and inverting the direction of a three-phase motors without direct third leg ( two legs). Directly mounting on a DIN rail , this product with a maximum current of semiconductors of 50 Amps. rms , can drive a motor with a current rating of 4,5 Amps.rms (or approximately 1,5kW under 400 V), taking the starting and reversing current into account. These products are designed with very high immunity components , without REED switches (only composed of solid state components) , with all protections : RC , VDR ,..... temporisation ,........., and 1600Volt peak voltage components. 83 25 3x 400VAC Internal block diagram : 1L1 -A2/B2 0V Forward 3L2 5L3 Reverse +B1 Control logic 12-30VDC + B1 -A2/B2 3L2 celduc France 5L3 24-500VAC Insulation (photocouplers) 8,5A AC53a (EN60947-1) With suitable heatsink See instruction sheet R F + A1 +A1 + B1 - A2/B2 1L1 EN60947-1 RC -VDR protection +A1 Reverse Forward 1L1 3L2 5L3 2T1 4T2 6T3 2T1 Solid State Motor Reverser SW9 2T1 4T2 4T2 6T3 6T3 M3~ Proud to serve you All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis. celduc r e l a i s S/MOT/SW960330/A/16/03/2000 page 2 / 5 F/GB Synoptique interne / Internal diagram for two leg models : Forward Reverse LED Controls Common A 2 /B2 Reverse Insu lation Switch RC network B1 + Forward lation Switch Mains or load 2T1 ~ Load or mains 3L2 ~ Mains or load 4T2 ~ Load or mains 5L3 ~ Mains or load 6T3 ~ Load or mains VDR Control lock Insu 1L1 ~ RC network VDR A1 + Input circuit Insu Insu lation Switch lation RC network Switch VDR RC network L3-T3 depending of models VDR Control Développé conformément aux normes / Designed in compliance with standards: ->EN60947-4-2 (V.D.E. 0660 part 109, I.E.C. 158-2) ->EN60947-1 & A11 ->EN60950 (V.D.E. 0805-> office equipment) (Pending approval) ->U.L. 508 (Pending approval) ->c.U.L (Pending approval) Plage de tension de commande / Control voltage range Plage de courant de commande / Control current range Tension de non fonctionnement/ Release voltage LED de visualisation / Display LED Uc Ic Ur 12-30VDC 15-25mADC 6VDC Yes Yes 30V no output fixed 70ms protection en cas de cdes simultanées / protection against simultaneous controls tension inverse maxi / Maximum reverse voltage Signal de sortie / Output signal temporisation inversion / Reversing time Urv Caractéristiques d'entrée-sortie (à 20°C) / Input-output characteristics (at 20°C) Isolement entrée-sortie/Input-output isolation @500m Isolement sortie-semelle/Output-case isolation @500m Tension assignée isolement/rated impulse voltage Caractéristiques générales / General characteristics Poids/Weight Plage de température de stockage / Storage temperature range Plage de température de fonctionnement/Operating temperature range Ui Ui Uimp Unit VRMS VRMS V 3300 3300 4000 130g -40 / +100 -40 / +100 Unit g °C °C celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 Output page 3 / 5 F/GB Tension nominale/ Standard mains voltage Plage de tension de fonctionnement / Mains voltage range tension crête non répétitive/ Non-repetitive maximum peak voltage Courant AC-53 maxi/ Max. nom. current (AC53a=AC3) @40°C Puissance moteur/ 3 pole power motor ( 3x400VAC) Chute directe / Max Direct voltage drop (@Ie) Courant crête non répétitif/ Non repetitive overload current (@ 1 cycle of 10ms) I2t value/ Melting limit (choice of fuse) @10ms Courant minimal de charge / Minimum load current facteur de puissance/ Power factor (@ Ie) Ue Un Up Ie Pn Ud 400 VAC 24-520VAC 1600V 4,5ARMS 1,5KW 1,4VRMS ITSM 550A 2 1500 A2s 100 mA 0 up to 1 20ms / 100ms 10ms 5 mARMS 500V/µs 25 up to 440Hz It Imin Pf Temps d'ouverture et de temporisation/ Turn on time-reversing time(@50Hz) ton/trv Temps d'ouverture/ Turn off time (@50Hz) toff Courant de fuite /Maximum leakage current (@Ue/50Hz) Ilk dv/dt / Max off state voltage rise dv/dt Fréquence de réseau / Operating frequency range f 4KV direct at output, 4KV with a clamp at input no turn on or damage 2KV in common mode, 1KV in differential mode (Input & output) no turn on or damage 10V/m E.M.C. Max conducted immunity level Test accord. to I.E.C.1000-4-4 (bursts) Max conducted immunity level Test acc. to I.E.C.1000-4-5 (el. shocks) Max radiated immunity level Test accord. to I.E.C.1000-4-3 Max electrostatic disch. immunity level Test accord. to I.E.C.1000-4-2 Max conducted emission level (0,8<Pf<1) Test according to EN55011 Max radiated emission level Test accord. to EN55011 @Ie Base/junction thermal resistance Rthjc Ambient/junction thermal resistance Rthja (relay mounted vertically) Weight Characteristics given at 25°C unless otherwise specified no turn on or damage 8KV in the air / 4KV touching no turn on or damage The conducted noise made by SSR depends on the wiring configuration and the load type. Test methods recommended by European E.M.C. standards giving results far from reality, we have chosen to advise the right filter suited for the customer's use: Refer to EMC chapter <30dBµV from 30 up to 230MHz ; <37dBµV from 230 up to 1000MHz Misc. 0,5K/W (1 leg) 5K/W 130g REVERSERS + HEATSINK SELECTION IN COMPLIANCE WITH EN60947-4-2 Relays with heatsink Ferraz fuse type Overload relay type SSR SELECTION motors soft-staters 14x51 size / max. rating Klöckner-Moeller am 8A/500V am 8A/500V am 12A/500V am 12A/500V am 12A/500V am 12A/500V Z00-2.4 Z00-6 Z00-6 Z00-6 Z00-10 Z00-10 for a permanent current Motor power In motor 0,75 kW 1,1 kW 1,5 kW 2,2 kW 3 kW 4 kW two legs (@ 400V) ambient =40°C 2A 2,6A 3,5A 5A 6,6A 8,5A SW960330 SW960330 SW960330 SW961230 (See data-sheet) SW961230 (See data-sheet) SW961230 (See data-sheet) For motor > 4kW consult us : we have some solutions celduc r e l a i s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 Total wasted power (W) Caractéristiques thermiques / Thermal curves : page 4 / 5 F/GB 30 30 25 25 20 20 15 15 10 10 5 5 0 0 2 Courant de surcharge non repetitif :ITSM / Non repetitive surge peak onstate current : ITSM 12 0 10 20 30 40 50 60 70 80 90 100 0 Ambient temperature (°C) Surge current Itsm (A peak) = f(t) for models with Itsm =550A 600 1 Itsm (Apeak) 1 : No repetitive Itsm (Apeak)=f(t) without voltage reapplied 4 6 8 10 RMS load current (A) 2 : Repetitive Itsm (Apeak)=f(t) with voltage reapplied for initial Tj =70°C SV 400 200 2 0 0,01 0,1 t (s) 1 10 Wiring of the control circuit: NUMBER OF WIRES 1 SOLID (No ferrule) MINIMUM TORQUE SCREWDRIVER TYPE 2 (DISTRIBUTION) FINE STRANDED (With ferrule) SOLID (No ferrule) FINE STRANDED (With ferrule) N.m 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 SV 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 POZIDRIV 2 1,2 Wiring of the power circuit: NUMBER OF WIRES 1 SOLID (No ferrule) 0,8 x 5,5 mm MINIMUM TORQUE SCREWDRIVER TYPE 2 (DISTRIBUTION) FINE STRANDED (With ferrule) SOLID (No ferrule) FINE STRANDED (With ferrule) N.m 1,5 ... 10 mm2 1,5 ... 6 mm2 1,5 ... 10 mm2 1,5 ... 6 mm2 0,8 x 5,5 mm POZIDRIV 2 1,8 celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 page 5 / 5 F/GB NOTE D'APPLICATION : UTILISER UN SW9 POUR L'INVERSION DE SENS DE ROTATION D'UN MOTEUR ASYNCHRONE MONOPHASE A CONDENSATEUR DE DEPHASAGE APPLICATION NOTE : USING A SW9 RELAY FOR REVERSING AN ASYNCHRONOUS SINGLE PHASE MOTOR WORKING WITH A PHASE SHIFTING CAPACITOR ALIMENTATION MONOPHASE / Main voltage L N Reverse Forward 1L1 3L2 12-30VDC celduc France Note : The SW9 relay which has been initially developped in order to reverse three phase asynchronous motors , can be used for reversing single phase motors . This relay has 4 power switches , a reversing temporization and a lock in case of simultaneous controls . If you need a big quantity for a single phase use , please contact us , because we are able to simplify the product as only 2 switches among 4 are used . 8,5A AC53a (EN60947-1) 1L1 3L2 5L3 2T1 4T2 Solid State Motor Reverser SW9 2T1 Note : Le relais SW9 développé initialement pour inverser le sens de rotation des moteurs asynchrones triphasés peut aussi être utilisé pour l'inversion de moteurs monophasés . Ce relais possède 4 voies de puissance , une temporisation à l'inversion et un verrouillage en cas de commande simultanée . Pour des quantités importantes , en utilisation monophasée , le produit peut être simplifié car seulement 2 voies sur 4 sont utilisées . 5L3 24-500VAC With suitable heatsink See instruction sheet R F +A1 +B1 -A2/B2 EN60947-1 4T2 6T3 6T3 C M celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19