ER2A thru ER2J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -2.0 Amperes SMB/DO-214AA FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .075(1.91) .083(2.11) .130(3.30) .155(3.94) .160(4.06) .185(4.70) .006(.152) .012(.305) .083(2.13) .096(2.44) MECHANICAL DATA .002(.051) .008(.203) .030(0.76) .050(1.27) Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 12mm tape (EIA-481) Weight: 0.003 ounces, 0.093 gram .200(5.08) .220(5.59) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ER2A ER2B ER2C ER2D ER2E ER2G ER2J UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 V Maximum Average Forward Rectified Current, at TL=110 C I(AV) 2.0 A Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 A Maximum Instantaneous Forward Voltage at 2.0A VF Maximum DC Reverse Current at Rated DC Blocking Voltage IR 0 @ TA=250C @ TA=1000C 0.95 1.25 5.0 TRR 35.0 Typical Junction Capacitance (Note 2) CJ 25.0 R Operating and Storage Temperature Range TJ , TSTG JL Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. A 150 Maximum Reverse Recovery Time (Note 1) Maximum Thermal Resistance (Note 3) V 1.7 20.0 -50 to +150 nS pF 0 C/W 0 C ER2A thru ER2J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ER2A THRU ER2J Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G trr 10 Noninductive +0.5A ( ) D.U.T. (+) 25 Vdc (approx) ( ) AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 50 Noninductive Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING 0 PULSE GENERATOR NOTE 2 1 NONInductive -0.25 (+) OSCILLOSCOPE NOTE 1 -1.0 NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. 1cm SET TIME BASE FOR 10ns/cm 2.4 2.0 SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.3x0.3"(8.0x8.0mm) COPPER PAD AREAS 1.6 1.2 0.8 0.4 0 0 20 40 60 80 100 120 140 160 LEAD TEMPERATURE, oC Fig. 3 - TYPICAL REVERSE CHARACTERISTICS 1000 Fig. 4 - TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES 50.0 0 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES TJ=100C 100 10 TJ=750C 0 TJ=25 C 1.0 0.1 40 60 80 100 120 ER2E 1.0 ER2J 0 140 PULSE WIDTH=300 S 2% DUTY CYCLE 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS Fig. 6 - TYPICAL JUNCTION CAPACITANCE Fig. 5 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 60 50 50 CAPACITANCE, pF PEAK FORWARD SURGE CURRENT, AMPERES TJ=25 C 0.1 0.01 0.4 0.01 20 ER2A 10.0 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD 40 30 20 40 0 TJ=25C f=1.0MHZ Vslg=50mVp-p 30 20 10 10 1 2 5 10 20 NUMBER OF CYCLES AT 60Hz 50 100 0.1 0.5 1 5 10 20 50 100 200 REVERSE VOLTAGE, VOLTS 500 1000