ER1A THRU ER1J SURFACE MOUNT SUPERFAST RECTIFIER VOLTAGE - 50 to 600 Volts CURRENT - 1.0 Ampere FEATURES l For surface mounted applications l Low profile package l l Built-in strain relief Easy pick and place l l Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory l Flammability Classification 94V-O Glass passivated junction l SMB/DO-214AA High temperature soldering: 260 ¢J /10 seconds at terminals MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.003 ounce, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=100 ¢J Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current TA=25 ¢J At Rated DC Blocking Voltage TA=100 ¢J Maximum Reverse Recovery Time (Note 1) Typical Junction capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range SYMBOLS ER1A ER1B ER1C ER1D ER1E ER1G ER1J UNITS 50 100 150 200 300 400 600 Volts VRRM 35 70 105 140 210 280 420 Volts VRMS 50 100 150 200 300 400 600 Volts VDC I(AV) 1.0 Amps IFSM 30.0 Amps VF IR TRR CJ R £KJL TJ ,TSTG NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts 3. 8.0mm2 (.013mm thick) land areas 0.95 1.25 5.0 100 35.0 10.0 34 -50 to +150 1.7 Volts £g A nS PF ¢J /W ¢J RATING AND CHARACTERISTIC CURVES ER1A THRU ER1J trr +0.5A 2.0 SINGLE PHASE HALF WAVE -0.25 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. RESISTIVE OR INDUCTIVE P.C.B MOUNTED ON 0.315×0.315"(8.0×8.0mm) PAD AREAS AVERAGE FORWARD CURRENT AMPERES 0 -1.0 SET TIME BASE FOR Source Impedance = 50 Ohms 1.0 25 1cm 50 75 100 125 150 175 LEAD TEMPERATURE, ¢J 50 ns/cm Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND Fig. 2-MAXIMUM AVERAGE FORWARD CURRENT RATING 1000 INSTANTANEOUS FORWARD CURRENT AMPERES IR-REVERSE LEAKAGE CURRENT, MICROAMPERES TEST CIRCUIT DIAGRAM 100 TJ = 125¢J 10 TJ = 75¢J 1 TJ = 25¢J 0.1 20 40 60 80 100 120 10 ER1A 1 ER1E ER1J 0.1 T J = 25 ¢J 0.01 0.001 0.2 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE VOLTS Fig. 3-TYPICAL REVERSE CHARACTERISTICS Fig. 4-TYPICAL FORWARD CHARACTERISTICS 14 30 JUNCTION CAPACITANCE, pF PEAK FORWARD SURGE CURRENT, AMPERES % OF PIV. VOLTS 25 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 20 15 10 5 1 2 5 10 20 50 100 12 10 TJ = 25¢J f = 1.0MHz Vsig = 50mVp-p 8.0 6.0 4.0 2.0 .1 1 10 100 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE, VOLTS Fig. 5-MAXIMUM NON-REPETITIVE SURGE CURRENT Fig. 6-TYPICAL JUNCTION CAPACITANCE