F06C05PT CHENMKO ENTERPRISE CO.,LTD THRU FAST RECOVERY RECTIFIER VOLTAGE RANGE 50 - 600 Volts F06C60PT CURRENT 6 Amperes FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Dual rectifier construction, positive centertap * Glass passivated chip junctions * Low power loss * Low forward voltage, high current capability * High surge current capability * Fast recovery times for high efficiency * High temperature soldering guaranteed : 260oC/10 seconds at terminals TO-220 .108 (2.75) .187 (4.7) .148 (3.8) .153 (3.9) .146 (3.7) .413 (10.5) .374 (9.5) .053 (1.3) .047 (1.2) .270 (6.9) .230 (5.8) .610 (15.5) .583 (14.8) MECHANICAL DATA Case: JEDEC TO-220 molded plastic Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Weight: 2.24 grams ( Approximately ) .157 (4.0) .583 (14.8) .531 (13.5) .051 (1.3) .043 (1.1) .035 (0.9) .028 (0.7) .102 (2.6) .091 (2.3) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. .020 (0.5) .126 (3.2) TO-220 Dimensions in inches and (millimeters) MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS SYMBOL F06C05PT F06C10PT F06C15PT F06C20PT F06C30PT F06C40PT F06C50PT F06C60PT UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 500 600 Volts Maximum RMS Voltage VRMS 35 70 105 140 210 280 350 420 Volts Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 500 600 Maximum Average Forward Rectified Current Volts IO 6.0 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 50 Amps Typical Junction capacitance per leg ( NOTE 1 ) CJ R Typical thermal resistance ( NOTE 2 ) Operating and Storage Temperature Range 55 30 pF o 5.0 JC TJ, TSTG C/W o -65 to +175 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 3.0 A DC Maximum DC reverse current at rated DC blocking voltage per leg Maximum reverse recovery time ( NOTE 3 ) per leg NOTES : 1. 2. 3. 4. F06C05PT F06C10PT F06C15PT F06C20PT VF o TC = 25 C TC = 100oC Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts Thermal resistance from junction to case per leg mounted on heatsink Reverse recovery test conditions : IF = 0.5 A, Ir = -1.0 A, Irr = -0.25 A. Suffix " C " = Common Cathod, Suffix " A " = Common Anode, Suffix " D " = Double. F06C40PT F06C50PT F06C60PT uAmps 70 150 UNITS Volts 5.0 IR trr F06C30PT 1.30 250 nS 2001-6 FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) D.U.T (+) 0 PULSE GENERATOR (NOTE 2) 25 Vdc (approx) (-) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A 1cm NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. SET TIME BASE FOR 50/100 nS/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 8.0 6.0 4.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 2.0 0 0 25 50 75 100 125 150 175 CASE TEMPERATURE ( OC ) 200 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 10 TJ =100oC 1.0 TJ =75oC .1 TJ =25oC 60 Pulse Width = 300uS 1% Duty Cycle 10 6.0 1.0 0.6 TJ =25oC 0.1 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1.8 FIG. 6 - TYPICAL JUNCTION CAPACITANCE 70 500 60 JUNCTION CAPACITANCE, ( pF ) PEAK FORWARD SURGE CURRENT, ( A ) AVERAGE FORWARD CURRENT, ( A ) RATING CHARACTERISTIC CURVES ( F06C05PT THRU F06C60PT ) 8.3ms Single Half Sine-Wave (JEDEC Method) 50 40 30 20 10 0 TJ = 25oC 200 100 60 40 F06C05PT~F06C20PT 20 F06C30PT~F06C60PT 10 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100