CHENMKO HMB12PT

HMB11PT
CHENMKO ENTERPRISE CO.,LTD
THRU
MINIATURE GLASS PASSIVATED
SINGLE-PHASE SURFACE MOUNT BRIDGE RECTIFIER
VOLTAGE RANGE 50 - 200 Volts CURRENT 0.5 Ampere
HMB13PT
FEATURES
* Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
* Surge overload rating of 35 Amperes peak
* Glass passivated chip junction
* Ideal for printed circuit board
* High temperature soldering guaranteed :
260oC/10 seconds at terminals
0.272(6.90)
MECHANICAL DATA
Case: JEDEC MD-S molded plastic
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Polarity syHMBols marked on body
Weight: 0.008 ounces, 0.22 gram
0.252(6.40)
0.161(4.10)
0.144(3.65)
0.179(4.55)
0.038(0.96)
0.019(0.48)
0.058(1.47)
0.054(1.37)
0.017(0.43)
0.105(2.67)
0.095(2.41)
0.008(0.20)
0.004(0.10)
0.117(2.97)
0.107(2.72)
0.106(2.70)
0.090(2.30)
0.114(2.90)
0.094(2.40)
Ratings at 25oC aHMBient temperature unless otherwise specified.
Single phase, half wave, 60 HZ, resistive or inductive load.
For capacitive load, derate current by 20%.
0.195(4.95)
0.062(1.57)
0.058(1.47)
0.029(0.74)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
0.205(5.21)
0.016(0.41)
0.006(0.15)
0.195(4.95)
0.049(1.24)
0.039(0.99)
MD-S
0.0075(0.19)
0.0065(0.16)
MD-S
Dimensions in inches and (millimeters)
MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted )
HMB12PT
HMB13PT
UNITS
Maximum Recurrent Peak Reverse Voltage
RATINGS
SYHMBOL
VRRM
50
100
200
Volts
Maximum RMS Voltage
VRMS
35
70
140
Volts
Maximum DC Blocking Voltage
VDC
50
100
200
Volts
Maximum Average Forward Rectified Current TA = 30oC
On glass-epoxy P.C.B.(NOTE 1)
On aluminum substrate (NOTE 2)
HMB11PT
IO
0.5
Amps
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
IFSM
30
Amps
Maximum Reverse Recovery Time
TRR
50
nSec
Typical Junction Capacitance (Note 3)
CJ
10
Typical thermal resistance per leg
R
Operating and Storage Temperature Range
pF
o
85
JA
TJ, TSTG
C/W
o
-55 to +150
C
ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted )
CHARACTERISTICS
SYHMBOL
Maximum Instantaneous Forward Voltage at 0.5 A DC
Maximum DC reverse current at rated
@ TA = 25oC
DC blocking voltage per leg
@ TA = 100oC
VF
HMB11PT
HMB12PT
HMB13PT
UNITS
1.1
Volts
5.0
uAmps
200
uAmps
IR
NOTES : 1. On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.27 X 1.27 mm) pads
2. On aluminum substrate P.C.B. with an area of 0.8 x 0.8 x 0.25" (20 x 20 x 6.4mm) mounted on 0.05 x 0.05" (1.27 x 1.27mm) solder pad
3. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts
2002-9
FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC
50
NONINDUCTIVE
10
NONINDUCTIVE
trr
+0.5A
(-)
D.U.T
(+)
25 Vdc
(approx)
(-)
0
PULSE
GENERATOR
(NOTE 2)
1
NONINDUCTIVE
OSCILLOSCOPE
(NOTE 1)
-0.25A
(+)
-1.0A
1cm
NOTES: 1. Rise Time = 7 ns max. Input Impedance =
1 megohm. 22 pF.
2. Rise Time = 10 ns max. Source Impedlance=
50 ohms.
SET TIME BASE FOR
10/20 nS/cm
FIG. 3 - TYPICAL REVERSE CHARACTERISTICS
PER BRIDGE ELEMENT
0.75
Copper Pads .05 In2
(1.27mm2) PC Board
0.50
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.25
0
0
25 50 75 100 125 150 175
LEAD TEMPERATURE ( OC )
FIG. 4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT, ( A )
INSTANTANEOUS REVERSE CURRENT, (uA)
FIG. 2 - TYPICAL FORWARD
CURRENT DERATING CURVE
20
1000
100
TJ =100oC
10
1
TJ =25oC
10
Pulse Width = 300uS
1% Duty Cycle
3.0
1.0
0.3
TJ =25oC
0.1
.03
.01
0.1
0
20
40
60
80
100
0
.2
PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % )
PEAK FORWARD SURGE CURRENT, ( A )
200
100
60
40
20
f = 1.0MHZ
Vsig = 50 mVp-p
10
TJ =25oC
6
4
2
1
.1
.2
.4
1.0
2
4
10
20
REVERSE VOLTAGE, ( V )
40
100
.4
.6
.8
1.0
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE, ( V )
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, ( pF )
AVERAGE FORWARD CURRENT, ( A )
RATING CHARACTERISTIC CURVES ( HMB11PT THRU HMB13PT )
FIG. 6 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER BRIDGE ELEMENT
35
30
Single Half Sine-Wave
(JEDEC Method)
25
20
15
10
5
0
1
2
5
10
20
NUMBER OF CYCLES AT 60 Hz
50
100