U16P20PT CHENMKO ENTERPRISE CO.,LTD THRU SUPER FAST RECOVERY RECTIFIER VOLTAGE RANGE 200 - 400 Volts U16P40PT CURRENT 16 Amperes FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Dual rectifier construction, positive centertap * Glass passivated chip junctions * Low power loss * Low forward voltage, high current capability * High surge current capability * Superfast recovery times for high efficiency * High temperature soldering guaranteed : 260oC/10 seconds at terminals .181 (4.60) .263 (6.70) .248 (6.30) .015 (0.381) PIN 1 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS K - HEATSINK o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. .027 (0.70) .019 (0.50) .035 (0.90) .023 (0.60) .059 (1.50) .035 (0.90) .244 (5.70) .208 (5.30) Case: JEDEC DPAK molded plastic Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Weight: 1.7 grams ( Approximately ) .094 (2.40) .086 (2.20) .022 (0.55) .017 (0.45) .394 (10.00) .354 (9.00) MECHANICAL DATA .113 (2.80) .087 (2.20) .059 (1.50) .051 (1.30) DPAK PIN 2 DPAK Dimensions in inches and (millimeters) MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) SYMBOL U16P20PT U16P30PT U16P40PT UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 200 300 400 Volts Maximum RMS Voltage VRMS 140 210 280 Volts Maximum DC Blocking Voltage VDC 200 300 400 Maximum Average Forward Rectified Current Volts IO 16.0 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 200 Amps Typical Junction capacitance per leg ( NOTE 1 ) CJ 85 R Typical thermal resistance ( NOTE 2 ) Operating and Storage Temperature Range pF o 2.2 JC TJ, TSTG C/W o -55 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 8.0 A DC Maximum DC reverse current at rated DC blocking voltage per leg Maximum reverse recovery time ( NOTE 3 ) per leg VF o TC = 25 C TC = 100oC IR trr NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to case per leg mounted on heatsink 3. Reverse recovery test conditions : IF = 0.5 A, Ir = -1.0 A, Irr = -0.25 A. U16P20PT U16P30PT 0.975 U16P40PT 1.30 5.0 150 35 UNITS Volts uAmps nS 2002-5 RATING CHARACTERISTIC CURVES ( U16P20PT THRU U16P40PT ) 12 8 Single Half Wave 60HZ Resistive or Inductive Load 4 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 16 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 8.3 ms Single Half Sine-Wave (JEDEC Method) 150 125 100 50 25 0 0 2 4 CASE TEMPERATURE, ( oC ) FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARCTERISTICS 20 40 60 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 TJ = 25oC 100 U16P20PT U16P30PT&40PT 10 1.0 PULSE WIDTH=300uS 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, (uA) 120 0.1 TJ = 75oC 10 1.0 TJ = 25oC 0.1 0 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 0 20 INSTANTANEOUS FORWARD VOLTAGE, (V) 40 FIG. 5 - TYPICAL JUNCTION CAPACITANCE TJ =25oC 100 10 .1 .4 60 80 100 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 1000 JUNCTION CAPACITANCE, ( pF ) INSTANTANEOUS FORWARD CURRENT, (A) 6 8 10 NUMBER OF CYCLES AT 60HZ 1.0 4 10 REVERSE VOLTAGE, ( V ) 40 80