Precision Sub-Miniature 5.0x3.2mm TCXO / VCTCXO Designed for Telecom Applications Description 2111 Comprehensive Drive M6 02 12. 0806 8M hz Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Features: The Connor-Winfield 5.0x3.2mm Temperature Compensated Crystal Oscillators and Voltage Controlled Temperature Compensated Crystal Oscillators are designed for use in applications requiring tight frequency stability in a small package. Through the use of Analog Temperature Compensation, this device is capable of holding sub 1-ppm stabilities over wide temperature ranges. 3.3V Operation LVCMOS or Clipped Sinewave Output Logic Sub-Miniature 5.0x3.2mm SMT Package Frequency Stabilities Available: ±0.28ppm with STRATUM 3 Holdover, ±0.50ppm or ±1.00ppm Temperature Ranges Available: 0 to 70°C -40 to 85°C Low Power <10mA Low Jitter <1pS RMS Tape and Reel Packaging RoHS Compliant / Lead Free Recommended for new designs Applications Ordering Information M602 - 012.8M STRATUM 3 Applications GPS Receivers Instrumentation Femtocells FTTH, FTTC TCXO SERIES 0.083 Max. (2.1mm) Top View 0.065 (1.65mm) 0.006 Typ. (0.15mm) 0.028 (0.71mm) 0.042 (1.07mm) 0.016 (0.41mm) M602 0806 12.8MHZ 0.197 (5.0mm) 0.050 (1.27mm) 0.028 (0.71mm) Pad 8 Pad 1 Dimensional Tolerance: +/-0.005 (+/-0.127mm) CENTER FREQUENCY Pad Connections Package Layout 0.126 (3.2mm) Example Part Number 0.008 Typ. (0.20mm) Bottom View 0.042 (1.07mm) Pad 1 2 3 4 5 6 7 8 Connection Voltage Control or N/C Do not connect Do not connect Ground Output Do not connect Do not connect Supply, Vcc Ordering Information - M 6 0 2 Type: Precision TCXO VCTCXO 3.2x5mm Temperature Range: 5 = 0 to 70° C 6 = -40 to 85° C Frequency Stability: 0 = ± 0.28 ppm 1 = ± 0.50 ppm 2 = ± 1.00 ppm Features: 2 = TCXO, LVCMOS, 3.3Vdc. 3 = TCXO, Clipped Sinewave, 3.3Vdc. 4 = VCTCXO, LVCMOS, 3.3Vdc. 5= VCTCXO, Clipped Sinewave, 3.3Vdc. 012.8M Output Frequency: Frequency Format -xxx.xM Min.* -xxx.xxxxxxM Max.* *Amount of numbers after the decimal point. M = MHz Example: M602-012.8M = 3.2x5mm, TCXO, LVCMOS, 3.3Vdc, -40 to 85C, +/-0.28ppm, Output Frequency 12.8MHz Bulletin Page Revision Date Tx214 1 of 4 01 05 Sep 2008 To order an M602 with an output frequency of: 6.4 MHz = M602-006.4M 20 MHz = M602-020.0M 38.88 MHz = M602-038.88M Consult the factory for available frequencies. Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com M6 02 12. 0806 8M hz Model Specifications Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range Holdover Stability M502 LVCMOS TCXO Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range Holdover Stability M602 LVCMOS TCXO Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range M512 LVCMOS TCXO Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range M612 LVCMOS TCXO M503 M504 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 40 MHz ±0.28ppm 3.3Vdc 0 to 70°C ±0.32ppm M505 Clipped Sinewave VCTCXO M603 M604 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 40 MHz ±0.28ppm 3.3Vdc -40 to 85°C ±0.32ppm M605 Clipped Sinewave VCTCXO M513 M514 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 40 MHz ±0.50ppm 3.3Vdc 0 to 70°C M515 Clipped Sinewave VCTCXO M613 M614 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 40 MHz ±0.50ppm 3.3Vdc -40 to 85°C M615 Clipped Sinewave VCTCXO Notes Features 1 2 Notes 1 2 Notes 1 3.3V Operation LVCMOS or Clipped Sinewave Output Logic Sub-Miniature 3.2x5.0mm SMT Package Frequency Stabilities Available: ±0.28ppm with STRATUM 3 Holdover, ±0.50ppm or ±1.00ppm Temperature Ranges Available: 0 to 70°C -40 to 85°C Low Power <10mA Low Jitter <1pS RMS Tape and Reel Packaging RoHS Compliant / Lead Free Recommended for new designs LVCMOS Test Circuit DNC DNC Notes Output Vcc Supply Voltage 8 7 6 2 3 5 15 pF* 1 .01 uF Bypass 4 1 N/C - TCXO VC - VCTCXO DNC DNC DNC = Do Not Connect * NPO Grade Component Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range M522 LVCMOS TCXO Model Number Output Type TCXO / VCTCXO Frequency Range Frequency Stability Supply Voltage Temperature Range M622 LVCMOS TCXO M523 M524 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 52 MHz ±1.00ppm 3.3Vdc 0 to 70°C M525 Clipped Sinewave VCTCXO M623 M624 Clipped Sinewave LVCMOS TCXO VCTCXO 6.4 to 52 MHz ±1.00ppm 3.3Vdc -40 to 85°C M625 Clipped Sinewave VCTCXO Notes Clipped Sinewave Test Circuit DNC DNC 1 AC Coupling Capacitor Vcc Supply Voltage Notes: 1) Frequency stability vs. change in temperature. [±(Fmax – Fmin)/2.Fo]. 2) Inclusive of frequency stability, supply voltage change (±1%), aging, for 24 hours. 8 7 6 2 3 10Kohm 10 pF* Notes .01 uF Bypass 4 1 N/C - TCXO VC - VCTCXO 1 DNC DNC DNC = Do Not Connect * NPO Grade Component US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Tx214 Page 2 of 4 Revision Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation Output 5 Date 01 05 Sep 2008 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com Electrical Specifications for all Models M6 02 12. 0806 8M hz ABSOLUTE MAXIMUM RATINGS PARAMETER UNITS Storage Temperature MINIMUM NOMINAL MAXIMUM UNITS -55 - 85 °C Supply Voltage (Vcc) -0.5 - 6.0 Vdc Input Voltage (Vc) -0.5 - Vcc+0.5 Vdc NOTE Features Operating Specifications Parameter Minimum Nominal Maximum Units Notes TCXO Frequency Calibration @ 25 C -1.00 - 1.00 ppm 1 Supply Voltage Variation. (Vcc±5%) -0.2 - 0.2 ppm Load Coefficient, ±5% -0.2 - 0.2 ppm Static Temperature Hysteresis -0.4 - 0.4 ppm Total Frequency Tolerance -4.60 - 4.60 ppm 3 3.135 3.3 3.465 Vdc 4 Supply Voltage (Vcc) Supply Current (Icc) - 6 10 mA Period Jitter - 3 5 ps rms Integrated Phase Jitter (BW=12kHz to 20MHz) - 0.3 1.0 ps rms SSB Phase Noise at 10Hz offset - -80 -70 dBc/Hz SSB Phase Noise at 100Hz offset - -110 -100 dBc/Hz SSB Phase Noise at 1KHz offset - -135 -130 dBc/Hz SSB Phase Noise at >10KHz offset - -150 -145 dBc/Hz SSB Phase Noise at >100KHz offset - -150 -150 dBc/Hz Start Up Time - - 10 ms Minimum Nominal Maximum Units 2 3.3V Operation LVCMOS or Clipped Sinewave Output Logic Sub-Miniature 3.2x5.0mm SMT Package Frequency Stabilities Available: ±0.28ppm with STRATUM 3 Holdover, ±0.50ppm or ±1.00ppm Temperature Ranges Available: 0 to 70°C -40 to 85°C Low Power <10mA Low Jitter <1pS RMS Tape and Reel Packaging RoHS Compliant / Lead Free Recommended for new designs LVCMOS Test Circuit Input Characteristics For Voltage Control (Pad 1) Parameter Control Voltage Range (Vcc = 3.3V) (Vc) DNC DNC 0.3 1.65 3.0 Vdc Frequency Tuning ±10 - - ppm Linearity ±5 - - % Notes 5 Output Vcc Supply Voltage 8 7 6 2 3 5 15 pF* Slope .01 uF Bypass Positive LVCMOS Output Characteristics Parameter LOAD Voltage Current Minimum Nominal - 15 90%Vcc - Maximum Units Notes - pF 6 - Vdc (High) (Voh) (Low) (Vol) - - 10%Vcc Vdc (High) (Ioh) -4 - - mA (Low) (Iol) - - 4 mA 45 50 55 % - - 8 ns Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum - - - Output Load Resistance - 10K - - 10 1.00 - Output Voltage 4) 5) 6) 7) 8) DNC = Do Not Connect * NPO Grade Component DNC DNC Units AC Coupling Capacitor 8 7 6 7 2 3 Ohms 8 - pF 8 - V pk-pk 10Kohm 10 pF* .01 uF Bypass 4 1 N/C - TCXO VC - VCTCXO DNC DNC DNC = Do Not Connect * NPO Grade Component TCXO: Initial calibration @ 25 C. Specifications at time of shipment after 48 hours of operation. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C. Inclusive of calibration @ 25 C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), reflow soldering process and 20 years aging. For best in application performance, careful selection of an external power source is critical. Select an external regulator that meets or xceeds to following specifications regarding voltage regulation tolerance, initial accuracy, temperature coefficient, voltage noise, and low voltage noise density. Factory Test Conditions: Initial Accuracy ±2mv, Noise (0.1Hz to 10 KHz) 15uV p-p, Voltage Noise Density = 50nV/(Square root Hz), Temperature Coefficient < 5ppm°C. Additional pull ranges are available; please contact the factory for additional information. For best performance it is recommended that the device connected to this output should have an equivalent input capacitance of 15pF. Output is DC coupled. For best performance it is recommended that the device connected to this output should have an equivalent input capacitance of 10pF. US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Tx214 Page 3 of 4 Revision Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation Output 5 Notes Notes 1) 2) 3) DNC DNC Vcc Supply Voltage Load Output Load Capacitance N/C - TCXO VC - VCTCXO Clipped Sinewave Test Circuit Clipped Sinewave Output Characteristics Parameter 4 1 Date 01 05 Sep 2008 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com Environmental Characteristics Vibration: Shock: Soldering: Solderability Vibration per Mil Std 883E Method 2007.3 Test Condition A Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. SMD product suitable for Convection Reflow soldering. Peak temperature 260 C. Maximum time above 220 C, 60 seconds. Solderability per Mil Std 883E Method 2003 Suggested Pad Layout To CMOS To Output Output External AC Coupling Capacitor Used For Clipped Sinwave Output Typical Phase Noise Model M602-012.8MHz 0.028 (0.71mm) 5 0.053 (1.35mm) Top View Keep Out Area* External Bypass Capacitor 0.01 uF 4 0.098 (2.49mm) 1 8 0.050 (1.27mm) 0.050 (1.27mm) To Ground Dimensional Tolerance: +/-0.005 (+/-0.127mm) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. Solder Profile Tape and Reel Specifications Temperature 260°C 260°C 220°C 180°C 150°C 120°C 0 120 S Max. Clipped Sinewave Output Waveform Time 10 S 60 S Max. 360 Sec. Max. LVCMOS Output Waveform 90% 50% 10% 10ns 200mV US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Tx214 Page 4 of 4 Revision Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation Date 01 05 Sep 2008