THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS 5.0V Sinewave OCVCXO Absolute Maximum Ratings Table 1.0 Parameter Storage Temperature Units Supply Voltage (Vcc) Minimum -55 Nominal - Maximum 125 Units °C -0.5 - 7 Vdc Minimum 3.2 -0.1 -50 -2 -100 -40 Nominal - Maximum 40 0.1 50 2 100 85 Units MHz ppm ppb ppb/day ppb °C 4.75 -5.0 -5.0 -100 - 5.00 - 5.25 5.0 5.0 4.0 2.2 100 5 Vdc ppb ppb W W ppb ppb/G Minimum Nominal Maximum Units 0.0 ±0.5 50K -10 2.5 - 5.0 10 Vdc ppm Ohm % (Fo) Supply Voltage Load Stability (+/-5%) Voltage Stability (+/-5%) Power Consumption: Turn On Power Consumption: Steady-State Warm Up 2G Tip-over (Vcc) Input Characteristics Parameter Control Voltage (Pin 3) Deviation @ 25°C referenced to Fo Input Impedance (Pin 3) Deviation Linearity (Vc) Note 1 2 Parameter LOAD Output Power Harmonics Spurious Output Jitter (BW=10Hz to Fo/2) SSB Phase Noise at 1Hz offset SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset SSB Phase Noise at 1KHz offset DESCRIPTION The Connor-Winfield OVC5EQ2BB is a 5.0V Oven Controlled Crystal Oscillator (OCVCXO) with a Sinewave output. The OVC5EQ2BB is designed for applications requiring low jitter and tight frequency stability. 3 4 5 5, 6 7 Table 3.0 Note Sinewave Output Characteristics 8 FEATURES Table 4.0 Minimum 45 3.0 - Nominal 50 - - - Maximum 55 -30 -80 2 -65 -95 -120 -145 Units Ohms dBm dBc dBc ps rms dBc/Hz dBc/Hz dBc/Hz dBc/Hz SSB Phase Noise at 10KHz offset - - -155 dBc/Hz SSB Phase Noise at 100KHz offset - - -155 dBc/Hz Package Characteristics OCVCXO Note FREQUENCY STABILITY: ±50ppb TEMPERATURE RANGE: -40 to 85°C 5.0V OPERATION SINEWAVE OUTPUT HERMETICALLY SEALED PACKAGE RoHS COMPLIANT / LEAD FREE Table 5.0 Package Soldering Process ORDERING INFORMATION Metal package: resistive welded, grounded case. RoHS compliant, lead free. See solder profile on page 2. OVC5EQ2BB Initial calibration referenced to Fo @ 25 C, Vc = 2.5Vdc, at time of shipment. Frequency vs. temperature stability, referenced to 25 C Frequency stability vs. 5% change in load, referenced to 50 ohms. Frequency vs. 5% change in supply voltage, referenced to 5.00 Vdc, Vc = 2.5Vdc. Vcc = 5.0Vdc. Measured @ 25 C. Measured @-40 C, within 5 minutes, referenced one hour after turn-on. Positive slope. DATA SHEET #: OVC5EQ2BB Table 2.0 Parameter Center Frequency Frequency Calibration (Vc = 2.5Vdc) Frequency Stability Aging: Daily Aging: First Year Operating Temperature Range 0838 OVC5EQ2BB 40.0 MHz Operating Specifications Notes: 1) 2) 3) 4) 5) 6) 7) 8) I( W Note Cx153 PAGE 1 OF 2 REV: 00 DATE: OCXO SERIES - 040.0M CENTER FREQUENCY Specifications subject to change without notice. 08/07/08 aCopyright 2008 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 245°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C ±5°C for 20 Seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. Solder Profile TOP VIEW Temperature 260°C 260°C I( W 0838 220°C 180°C 150°C OVC5EQ2BB 40.0 MHz 120°C 0 120 S Max. Package Outline Time 10 S 60 S Max. 360 Sec. Max. Pin Connections Pin 1 2 3 4 5 Connection Output Ground, Case Control Voltage N/C Vcc Test Circuit Control Voltage Dimensional Tolerance: ±.005 (.127mm) Specifications subject to change without notice. DATA SHEET #: Cx153 PAGE 2 OF 2 REV: 00 DATE: 08/07/08 aCopyright 2008 Connor-Winfield all rights reserved.