Compact Medium Power Amplifier for EMI/EMC Test and Measurement Applications 2 .0 - 8 .0 GHz The VZS/C-6963J2 Series Compact HPA, with 250W or 340W Traveling Wave Tube Global Applications Five rack units tall (8.75 in, 222 mm) 230 VAC operation. Meets International Safety Standard EN61010 and Electromagnetic Compatibility 89/336/EEC. Versatile Worldwide Support Modular design and built-in fault diagnostic capability, backed by CPI’s worldwide 24-hour customer support network that includes fifteen regional factory service centers. An integral solid state pre-amplifier and IEEE interface are included as standard features. 45 River Drive Georgetown, Ontario, Canada L7G 2J4 tel: +1 (905) 877-0161 fax: +1 (905) 877-5327 e-mail: [email protected] www.cpii.com/satcom Compact Medium Power Amplifier Ultra-wideband, automatic fault recycle, userfriendly microprocessor-controlled logic with integrated computer interface, digital metering, electronic variable attenuation, soft-fail when subjected to extreme load SWR conditions, quiet operation for laboratory environment. 2.0 - 8.0 GHz Compact 2 .0 - 8. 0 G Hz SPECIFICATIONS, VZS/C-6963J2 Environmental (Operating) Electrical OPTIONS: • Input Isolator (-1 dB gain) • Remote Control Panel • 115 VAC External Step-Up Transformer Ambient Temperature -10° to +40°C operating Relative Humidity 95% non-condensing Altitude Up to 10,000 ft (3000 m) with standard adiabatic derating of 2°/1000 ft. 6.0 GHz Shock and Vibration Gain 54 dB min. at rated power output; 56 dB typ. at small signal Designed to meet conditions normally encountered in the laboratory Acoustic Noise 65 dBA @ 3 ft. from amplifier RF Level Adjust 0 to 20 dB continuous Gain Stability ±0.25 dB/24 hr max. (at constant drive and temp.) Gain Variation 12.0 dB pk-pk max. over the 6.0 GHz bandwidth, typ. Input VSWR 2.5:1 typ. 1.7:1 max. (with optional input isolator) Output VSWR 2.5:1 typ. Load VSWR 1.5:1 max. for full spec compliance; 2.0:1 max. continuous operation; any value without damage Frequency 2.0 to 8.0 GHz Output Power TWT Flange 250 W or 340 W min. 225 W or 300 W min. Bandwidth Residual AM -50 dBc below 10 kHz; -20 [1.3 + log F (kHz)] dBc, 10 kHz to 500 kHz; -85 dBc above 500 kHz Phase Noise Meets IESS-308/309 with 3 dB margin Noise and Spurious -50 dBc typ. excluding harmonics Harmonic Content -3 dBc typical at lower band edge Primary Power 220-240 VAC ±10%, single phase, 47-63 Hz Power Consumption 2.6 kVA typ. 3.0 kVA max. Inrush Current 200% max. Mechanical Cooling (TWT) Forced air with integral blower. Rear air intake and exhaust. RF Input Connection Type N female RF Output Connection Type N female RF Power Monitors Type-N female, -50 dB nominal Dimensions (W x H x D) 19 x 8.75 x 26 in. (483 x 222 x 661 mm) Weight 110 lbs (50 kg) Safety EN61010 Certificate Number: 30515 For more detailed information, please refer to the corresponding CPI Technical Description. Note: Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. MKT 224, ISSUE 1 09/07 PDF