TI TUSB9261PVP

TUSB9261
USB 3.0 TO SATA BRIDGE
Data Manual
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Literature Number: SLLSE67B
March 2011 – Revised May 2011
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
Contents
8
................................................................................................................ 5
1.1
TUSB9261 Features ........................................................................................................ 5
1.2
Target Applications ......................................................................................................... 5
RELATED DOCUMENTS ....................................................................................................... 6
2.1
TUSB9261 Related Documentation ...................................................................................... 6
INTRODUCTION .................................................................................................................. 7
3.1
System Overview ........................................................................................................... 7
3.2
Device Block Diagram ...................................................................................................... 7
OPERATION ....................................................................................................................... 9
4.1
General Functionality ....................................................................................................... 9
4.2
Firmware Support ......................................................................................................... 10
4.3
GPIO/PWM LED Designations .......................................................................................... 10
4.4
Power Up and Reset Sequence ......................................................................................... 11
SIGNAL DESCRIPTIONS ..................................................................................................... 12
CLOCK CONNECTIONS ...................................................................................................... 16
6.1
Clock Source Requirements ............................................................................................. 16
6.2
Clock Source Selection Guide ........................................................................................... 16
6.3
Oscillator .................................................................................................................... 17
6.4
Crystal ....................................................................................................................... 17
ELECTRICAL SPECIFICATIONS .......................................................................................... 18
7.1
Absolute Maximum Ratings .............................................................................................. 18
7.2
Thermal Information ....................................................................................................... 18
7.3
Recommended Operating Conditions .................................................................................. 18
7.4
DC Electrical Characteristics for 3.3-V Digital I/O ..................................................................... 19
POWER CONSUMPTION ..................................................................................................... 20
2
Contents
1
2
3
4
5
6
7
MAIN FEATURES
Copyright © 2011, Texas Instruments Incorporated
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
List of Figures
3-1
Device Block Diagram ............................................................................................................. 8
6-1
Typical Crystal Connections .................................................................................................... 16
Copyright © 2011, Texas Instruments Incorporated
List of Figures
3
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
List of Tables
4-1
GPIO/PWM LED Designations ................................................................................................. 10
5-1
I/O Definitions ..................................................................................................................... 12
5-2
Clock and Reset Signals ........................................................................................................ 12
5-3
SATA Interface Signals .......................................................................................................... 12
5-4
USB Interface Signals ........................................................................................................... 13
5-5
Serial Peripheral Interface (SPI) Signals ...................................................................................... 13
5-6
JTAG, GPIO, and PWM Signals
5-7
6-1
6-2
8-1
8-2
4
...............................................................................................
Power and Ground Signals .....................................................................................................
Oscillator Specification ..........................................................................................................
Crystal Specification .............................................................................................................
SuperSpeed USB Power Consumption .......................................................................................
High Speed USB Power Consumption ........................................................................................
List of Tables
14
15
17
17
20
20
Copyright © 2011, Texas Instruments Incorporated
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
USB 3.0 TO SATA BRIDGE
Check for Samples: TUSB9261
1
MAIN FEATURES
1.1
TUSB9261 Features
• Universal Serial Bus (USB)
– SuperSpeed USB 3.0 Compliant - TID 340730020
• Integrated Transceiver Supports SS/HS/FS Signaling
– Best in Class Adaptive Equalizer
• Allows for Greater Jitter Tolerance in the Receiver
– USB Class Support
• USB Attached SCSI Protocol (UASP)
• USB Mass Storage Class Bulk-Only Transport (BOT)
• Support for Error Conditions Per the 13 Cases (Defined in the BOT Specification)
• USB Bootability Support
• USB Human Interface Device (HID)
– Supports Firmware Update Via USB, Using a TI Provided Application
• SATA Interface
– Serial ATA Specification Revision 2.6
• gen1i, gen1m, gen2i, and gen2m
– Support for Mass-Storage Devices Compatible With the ATA/ATAPI-8 Specification
• Integrated ARM Cortex M3 Core
– Customizable Application Code Loaded From EEPROM Via SPI Interface
– Two Additional SPI Port Chip Selects for Peripheral Connection
– Up to 12 GPIOs for End-User Configuration
• 2 GPIOs Have PWM Functionality for LED Blink Speed Control
– Serial Communications Interface for Debug (UART)
• General Features
– Integrated Spread Spectrum Clock Generation Enables Operation from a Single Low Cost Crystal or
Clock Oscillator
• Supports 20, 25, 30 or 40 MHz
– A JTAG Interface is Used for IEEE1149.1 and IEEE1149.6 Boundary Scan
– Available in a Fully RoHS Compliant Package
1
1.2
•
•
•
•
Target Applications
External HDD/SSD
External DVD
External CD
HDD-Based Portable Media Player
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
2
RELATED DOCUMENTS
2.1
TUSB9261 Related Documentation
1. TUSB9260 Implementation Guide (SLLA301)
2. TUSB9260/TUSB9261 Flash Burner User Guide (SLLU125)
6
RELATED DOCUMENTS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
3
INTRODUCTION
3.1
System Overview
The TUSB9261 is an ARM cortex M3 microcontroller based USB 3.0 to serial ATA bridge. It provides the
necessary hardware and firmware to implement a USB attached SCSI protocol (UASP) compliant mass
storage device suitable for bridging hard disk drives (HDD), solid state disk drives (SSD), optical drives
and other compatible SATA 1.5-Gbps or SATA 3.0-Gbps devices to a USB 3.0 bus. In addition to UASP
support, the firmware implements the mass storage class bulk-only transport (BOT), and USB human
interface device (HID) interfaces.
USB 3.0
(1)
SuperSpeed
PC
with
USB 3.0
Support
SATA
Gen1/2
HDD
USB 2.0
(1)
High-speed
TUSB9260
TUSB9261
(1)
3.2
USB connection is made at either SuperSpeed or High-Speed depending on the upstream connection support.
Device Block Diagram
The major functional blocks are as follows:
• Cortex M3 microcontroller subsystem including the following peripherals:
– Time interrupt modules, including watchdog timer
– Universal asynchronous receive/transmit (SCI)
– Serial peripheral interface (SPI)
– General purpose input/output (GPIO)
– PWM for support of PWM outputs (PWM)
• USB 3.0 Core (endpoint controller) and integrated USB 3.0 PHY
• AHCI compliant SATA controller and integrated SATA PHY
– Supporting gen1i, gen1m, gen2i, and gen2m
• Chip level clock generation and distribution
• Support for JTAG 1149.1 and 1149.6
INTRODUCTION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
7
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
ROM
www.ti.com
GRSTz
ARM
Cortex M3
VDD3.3
RAM
64 kB
VDD1.1
TCK
TMS
TDO
TDI
TRST
JTAG
Data Path
RAM
80 kB
XI
Clock
Generation
Power
and
Reset
Distribution
USB 3.0
Device
Controller
X0
SATA
AHCI
Watchdog
Timer
Timer
USB_R1
USB_R1RTN
DP/DM
USB HS/FS
PHY
VBUS
SSRX+
SSRX-
USB SS
PHY
SSTX+
SSTX-
SATARX+
SATARX-
SATATX+
SATATX-
PWM[1:0]
CS[2:0]
DATA_IN
SCLK
GPIO[11:0]
GPIO
PWM
SPI
DATA_OUT
UartRX
UartTX
SCI
(UART)
SATA II
PHY
Figure 3-1. Device Block Diagram
8
INTRODUCTION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
4
OPERATION
4.1
General Functionality
The TUSB9261 ROM contains boot code that executes after a global reset which performs the initial
configuration required to load a firmware image from an attached SPI flash memory to local RAM. In the
absence of an attached SPI flash memory or a valid image in the SPI flash memory, the firmware will idle
and wait for a connection from a USB host through its HID interface which is also configured from the boot
code. The latter can be accomplished using a custom application or driver to load the firmware from a file
resident on the host system.
Once the firmware is loaded it configures the SATA advanced host controller interface host bus adapter
(AHCI) and the USB device controller. In addition, the configuration of the AHCI includes a port reset
which initiates an out of band (OOB) TX sequence from the AHCI link layer to determine if a device is
connected, and if so negotiate the connection speed with the device (3.0 Gbps or 1.5 Gbps).
The configuration of the USB device controller includes creation of the descriptors, configuration of the
device endpoints for support of UASP and USB mass storage class bulk-only transport (BOT), allocation
of memory for the transmit request blocks (TRBs), and creation of the TRBs necessary to transmit and
receive packet data over the USB. In addition, the firmware provides any other custom configuration
required for application specific implementation, for example a HID interface for user initiated backup.
After USB device controller configuration is complete, if a SATA device was detected during the AHCI
configuration the firmware connects the device to the USB bus when VBUS is detected. According to the
USB 3.0 specification, the TUSB9261 will initially try to connect at SuperSpeed USB, if successful it will
enter U0; otherwise, after the training time out it will enable the DP pull up and connect as a USB 2.0
high-speed or full-speed device depending on the speed supported by host or hub port.
When connected, the firmware presents the BOT interface as the primary interface and the UASP
interface as the secondary interface. If the host stack is UASP aware, it can enable the UASP interface
using a SET_INTERFACE request for alternate interface 1.
Following speed negotiation, the device should transmit a device to host (D2H) FIS with the device
signature. This first D2H FIS is received by the link layer and copied to the port signature register. When
firmware is notified of the device connection it queries the device for capabilities using the IDENTIFY
DEVICE command. Firmware then configures the device as appropriate for its interface and features
supported, for example an HDD that supports native command queuing (NCQ).
OPERATION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
9
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
4.2
www.ti.com
Firmware Support
Default firmware support is provided for the following:
• SuperSpeed USB and USB 2.0 High-Speed and Full-Speed
• USB Attached SCSI Protocol (UASP)
• USB Mass Storage Class (MSC) Bulk-Only Transport (BOT)
– Including the 13 Error Cases
• USB Mass Storage Specification for Bootability
• USB Device Class Definition for Human Interface Devices (HID)
– Firmware Update and Custom Functionality (e.g. One-Touch Backup)
• Serial ATA Advanced Host Controller Interface (AHCI)
• General Purpose Input/Output (GPIO)
– LED Control and Custom Functions (e.g. One-Touch Backup Control)
• Pulse Width Modulation (PWM)
– LED Dimming Control
• Serial Peripheral Interface (SPI)
– Firmware storage and storing Custom Device Descriptors
• Serial Communications Interface (SCI)
– Debug Output Only
4.3
GPIO/PWM LED Designations
The default firmware provided by TI drives the GPIO and PWM outputs as listed in the table below.
Table 4-1. GPIO/PWM LED Designations
GPIO0
SW heartbeat
00: U3 state or default
01: U2 state
GPIO1/GPIO5
USB3 power state (U0-U3)
GPIO2
HS/FS suspend
GPIO3
Push button input on customer board
GPIO4
Not used
GPIO6
FS/HS connected
GPIO7
SS connected
PWM0
Disk activity
PWM1
U3 or HS/FS suspend state (fades high and low)
GPIO10
(SPICS1)
Not used
GPIO11
(SPICS2)
Not used
10: U1 state
11: U0 state
The LED’s on the TUSB9261 Product Development Kit (PDK) board are connected as in the table above.
Please see the TUSB9261 PDK Guide for more information on GPIO LED connection and usage. This
EVM is available for purchase, contact TI for ordering information.
10
OPERATION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
4.4
Power Up and Reset Sequence
The TUSB9261 does not have specific power sequencing requirements with respect to the core power
(VDD), I/O power (VDD33), or analog power (VDDA33). The core power (VDD) or IO power (VDD33) may
be powered up for an indefinite period of time while others are not powered up if all of these constraints
are met:
• All maximum ratings and recommended operating conditions are observed.
• All warnings about exposure to maximum rated and recommended conditions are observed,
par-ticularly junction temperature. These apply to power transitions as well as normal operation.
• Bus contention while VDD33 is powered up must be limited to 100 hours over the projected life-time of
the device.
• Bus contention while VDD33 is powered down may violate the absolute maximum ratings.
A supply bus is powered up when the voltage is within the recommended operating range. It is powered
down when it is below that range, either stable or in transition.
A minimum reset duration of 1 ms is required. This is defined as the time when the power supplies are in
the recommended operating range to the de-assertion of GRSTz.
OPERATION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
11
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
5
www.ti.com
SIGNAL DESCRIPTIONS
Table 5-1. I/O Definitions
I/O TYPE
DESCRIPTION
I
Input
O
Output
I/O
Input - Output
PU
Internal pull-up resistor
PD
Internal pull-down resistor
PWR
Power signal
Table 5-2. Clock and Reset Signals
TERMINAL
NAME
PIN
NO.
I/O
DESCRIPTION
GRSTz
4
I
PU
Global power reset. This reset brings all of the TUSB9261 internal registers to their default
states. When GRSTz is asserted, the device is completely nonfunctional.
XI
52
I
Crystal input. This terminal is the crystal input for the internal oscillator. The input may alternately
be driven by the output of an external oscillator. When using a crystal a 1-MΩ feedback resistor
is required between X1 and XO.
XO
54
O
Crystal output. This terminal is the crystal output for the internal oscillator. If XI is driven by an
external oscillator this pin may be left unconnected. When using a crystal a 1-MΩ feedback
resistor is required between X1 and XO.
Frequency select. These terminals indicate the oscillator input frequency and are used to
configure the correct PLL multiplier. The field encoding is as follows:
FREQSEL[1:0]
31, 30
I
PU
FREQSEL[1]
FREQSEL[0]
INPUT CLOCK FREQUENCY
0
0
20 MHz
0
1
25 MHz
1
0
30 MHz
1
1
40 MHz
Table 5-3. SATA Interface Signals (1)
TERMINAL
PIN
NO.
I/O
SATA_TXP
57
O
Serial ATA transmitter differential pair (positive)
SATA_TXM
56
O
Serial ATA transmitter differential pair (negative)
SATA_RXP
60
I
Serial ATA receiver differential pair (positive)
SATA_RXM
59
I
Serial ATA receiver differential pair (negative)
NAME
(1)
12
DESCRIPTION
Note that the default firmware and reference design for the TUSB9261 have the SATA TXP/TXM swapped for ease of routing in the
reference design. If you plan to use the TI default firmware please review the reference design in the TUSB9261 DEMO User’s Guide
(SLLU139) for proper SATA connection.
SIGNAL DESCRIPTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
Table 5-4. USB Interface Signals
TERMINAL
PIN
NO.
I/O
USB_SSTXP
43
O
SuperSpeed USB transmitter differential pair (positive)
USB_SSTXM
42
O
SuperSpeed USB transmitter differential pair (negative)
USB_SSRXP
46
I
SuperSpeed USB receiver differential pair (positive)
USB_SSRXM
45
I
SuperSpeed USB receiver differential pair (negative)
USB_DP
36
I/O
USB High-speed differential transceiver (positive)
USB_DM
35
I/O
USB High-speed differential transceiver (negative)
USB_VBUS
50
I
USB bus power
USB_R1
38
O
Precision resistor reference. A 10-kΩ ±1% resistor should be connected between R1 and R1RTN.
USB_R1RTN
39
I
Precision resistor reference return
NAME
DESCRIPTION
Table 5-5. Serial Peripheral Interface (SPI) Signals
TERMINAL
NAME
PIN
NO.
I/O
DESCRIPTION
SPI_SCLK
17
O
PU
SPI clock
SPI_DATA_OUT
18
O
PU
SPI master data out
SPI_DATA_IN
20
I
PU
SPI master data in
SPI_CS0
21
O
PU
Primary SPI chip select for Flash RAM
23
I/O
PU
SPI chip select for additional peripherals. When not used for SPI chip select this pin may be used
as general purpose I/O.
22
I/O
PU
SPI chip select for additional peripherals. When not used for SPI chip select this pin may be used
as general purpose I/O.
SPI_CS2/
GPIO11
SPI_CS1/
GPIO10
SIGNAL DESCRIPTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
13
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
Table 5-6. JTAG, GPIO, and PWM Signals
TERMINAL
NAME
I/O
PIN
NO.
DESCRIPTION
JTAG_TCK
25
I
PD
JTAG test clock
JTAG_TDI
26
I
PU
JTAG test data in
JTAG_TDO
27
O
PD
JTAG test data out
JTAG_TMS
28
I
PU
JTAG test mode select
JTAG_TRSTz
29
I
PD
JTAG test reset
GPIO9/UART_TX
6
I/O
PU
GPIO/UART transmitter. This terminal can be configured as a GPIO or as the transmitter for a
UART channel. This pin defaults to a general purpose output.
GPIO8/UART_RX
5
I/O
PU
GPIO/UART receiver. This terminal can be configured as a GPIO or as the receiver for a UART
channel. This pin defaults to a general purpose output.
GPIO7
16
I/O
PD
GPIO6
15
I/O
PD
GPIO5
14
I/O
PD
GPIO4
13
I/O
PD
GPIO3
11
I/O
PD
GPIO2
10
I/O
PD
GPIO1
9
I/O
PD
GPIO0
8
I/O
PD
PWM0
2
O
PD (1)
PWM1
3
O
PD (1)
(1)
14
Configurable as general purpose input/outputs
Pulse Width Modulation (PWM). Can be used to drive status LED's.
PWM pull down resistors are disabled by default. A firmware modification is required to turn them on. All other internal pull up/down
resistors are enabled by default.
SIGNAL DESCRIPTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
Table 5-7. Power and Ground Signals
TERMINAL
NAME
PIN
NO.
I/O
DESCRIPTION
VDD
1, 12,
19, 32,
33, 41,
47, 49,
55, 61,
63
PWR
1.1-V power rail
VDD33
7, 24,
51
PWR
3.3-V power rail
VDDA33
34, 40,
48, 62
PWR
3.3-V analog power rail
VSSOSC
53
PWR
Oscillator ground. If using a crystal, this should not be connected to PCB ground plane. If
using an oscillator, this should be connected to PCB ground. See the Clock Source
Requirements section for more details.
VSS
44, 58
PWR
Ground
VSS
65
PWR
Ground - Thermal Pad
NC
37, 64
—
No connect, leave floating
SIGNAL DESCRIPTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
15
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
6
CLOCK CONNECTIONS
6.1
Clock Source Requirements
The TUSB9261 supports an external oscillator source or a crystal unit. If a clock is provided to XI instead
of a crystal, XO is left open and VSSOSC should be connected to the PCB ground plane. Otherwise, if a
crystal is used, the connection needs to follow the guidelines below.
Since XI and XO are coupled to other leads and supplies on the PCB, it is important to keep them as short
as possible and away from any switching leads. It is also recommended to minimize the capacitance
be-tween XI and XO. This can be accomplished by connecting the VSSOSC lead to the two external
capaci-tors CL1 and CL2 and shielding them with the clean ground lines. The VSSOSC should not be
connected to PCB ground when using a crystal.
Load capacitance (Cload) of the crystal varying with the crystal vendors is the total capacitance value of the
entire oscillation circuit system as seen from the crystal. It includes two external capacitors CL1 and CL2
in Figure 6-1. The trace length between the decoupling capacitors and the corresponding power pins on
the TUSB9261 needs to be minimized. It is also recommended that the trace length from the capacitor
pad to the power or ground plane be minimized.
CL1
XI
VSSOSC
Crystal
XO
CL2
Figure 6-1. Typical Crystal Connections
6.2
Clock Source Selection Guide
Reference clock jitter is an important parameter. Jitter on the reference clock will degrade both the
trans-mit eye and receiver jitter tolerance no matter how clean the rest of the PLL is, thereby impairing
system performance. Additionally, a particularly jittery reference clock may interfere with PLL lock
detection mechanism, forcing the Lock Detector to issue an Unlock signal. A good quality, low jitter
reference clock is required to achieve compliance with supported USB3.0 standards. For example,
USB3.0 specification requires the random jitter (RJ) component of either RX or TX to be 2.42 ps (random
phase jitter calculated after applying jitter transfer function - JTF). As the PLL typically has a number of
additional jitter components, the Reference Clock jitter must be considerably below the overall jitter
budget.
16
CLOCK CONNECTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
6.3
Oscillator
XI should be tied to the 1.8-V clock source and XO should be left floating.
VSSOSC should be connected to the PCB ground plane.
A 20-, 25-, 30- or 40-MHz clock can be used.
Table 6-1. Oscillator Specification
PARAMETER
CXI
XI input capacitance
VIL
Low-level input voltage
VIH
High-level input voltage
Ttosc_i
Frequency tolerance
Tduty
Duty cycle
TR/TF
Rise/Fall time
RJ
CONDITIONS
MIN
TJ = 25°C
TYP
MAX
UNIT
0.414
pF
0.7
V
1.05
Operational temperature
V
–50
50
50
ppm
55
%
20% - 80 %
6
ns
Reference clock RJ
JTF (1 sigma) (1) (2)
0.8
ps
TJ
Reference clock TJ
JTF (total p-p) (2) (3)
25
ps
Tp-p
Reference clock jitter
(absolute p-p) (4)
50
ps
(1)
(2)
(3)
(4)
45
Sigma value assuming Gaussian distribution
After application of JTF
Calculated as 14.1 x RJ + DJ
Absolute phase jitter (p-p)
6.4
Crystal
A parallel, 20-pF load capacitor should be used if a crystal source is used.
VSSOSC should not be connected to the PCB ground plane.
A 20-, 25-, 30- or 40-MHz crystal can be used.
Table 6-2. Crystal Specification
PARAMETER
CONDITIONS
MIN
Oscillation mode
TYP
MAX
UNIT
Fundamental
20
fO
25
Oscillation frequency
MHz
30
40
ESR
Ttosc_i
Equivalent series resistance
Frequency tolerance
Frequency stability
20 MHz and 25 MHz
50
30 MHz
40
40 MHz
30
Operational temperature
±50
ppm
±50
ppm
24
pF
1 year aging
12
20
Ω
CL
Load capacitance
CSHUNT
Crystal and board stray
capacitance
4.5
pF
Drive level (max)
0.8
mW
CLOCK CONNECTIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
17
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
7
ELECTRICAL SPECIFICATIONS
7.1
Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
VALUE
UNIT
VDD
Steady-state supply voltage
–0.3 to 1.4
V
VDD33/
VDDA33
Steady-state supply voltage
–0.3 to 3.8
V
7.2
Thermal Information
TUSB9261
THERMAL METRIC
PVP
UNITS
64 PINS
Junction-to-ambient thermal resistance (1)
θJA
30.2
(2)
θJCtop
Junction-to-case (top) thermal resistance
θJB
Junction-to-board thermal resistance (3)
6.1
ψJT
Junction-to-top characterization parameter (4)
0.4
ψJB
Junction-to-board characterization parameter (5)
6.1
(6)
0.9
θJCbot
(1)
(2)
(3)
(4)
(5)
(6)
Junction-to-case (bottom) thermal resistance
11.0
°C/W
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific
JEDEC-standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
7.3
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
VDD
Digital 1.1 supply voltage
1.045
1.1
1.155
V
VDD33
Digital 3.3 supply voltage
3
3.3
3.6
V
VDDA33
Analog 3.3 supply voltage
3
3.3
3.6
V
VBUS
Voltage at VBUS PAD
0
1.155
V
TA
Operating free-air temperature range
-40
85
°C
TJ
Operating junction temperature range
-40
18
100
°C
HBM ESD
2000
V
CDM ESD
500
V
ELECTRICAL SPECIFICATIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
www.ti.com
7.4
DC Electrical Characteristics for 3.3-V Digital I/O
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DRIVER
TR
Rise time
5 pF
1.5
TF
Fall time
5 pF
1.53
IOL
Low-level output current
VDD33 = 3.3 V, TJ = 25°C
6
IOH
High-level output current
VDD33 = 3.3 V, TJ = 25°C
–6
VOL
Low-level output voltage
IOL = 2 mA
VOH
High-level output voltage
IOL = –2 mA
VO
Output voltage
ns
ns
mA
mA
0.4
2.4
V
V
0
VDD33
V
RECEIVER
VI
Input voltage
0
VDD33
V
VIL
Low-level input voltage
0
0.8
V
VIH
High-level input voltage
2
Vhys
Input hysteresis
tT
Input transition time (TR and TF)
II
Input current
VI = 0 V to VDD33
CI
Input capacitance
VDD33 = 3.3 V, TJ = 25°C
V
200
mV
10
ns
5
µA
0.384
ELECTRICAL SPECIFICATIONS
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
pF
19
TUSB9261
SLLSE67B – MARCH 2011 – REVISED MAY 2011
8
www.ti.com
POWER CONSUMPTION
Table 8-1. SuperSpeed USB Power Consumption
POWER RAIL
TYPICAL ACTIVE CURRENT (mA) (1)
TYPICAL SUSPEND CURRENT (mA) (2)
VDD11
291
153
65
28
VDD33
(1)
(2)
(3)
(3)
Transferring data via SS USB to a SSD SATA Gen II device. No SATA power management, U0 only.
SATA Gen II SSD attached no active transfer. No SATA power management, U0 only.
All 3.3-V power rails connected together.
Table 8-2. High Speed USB Power Consumption
(1)
(2)
(3)
20
POWER RAIL
TYPICAL ACTIVE CURRENT (mA) (1)
TYPICAL SUSPEND CURRENT (mA) (2)
VDD11
172
153
VDD33 (3)
56
28
Transferring data via HS USB to a SSD SATA Gen II device. No SATA power management.
SATA Gen II SSD attached no active transfer. No SATA power management.
All 3.3-V power rails connected together.
POWER CONSUMPTION
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TUSB9261
PACKAGE OPTION ADDENDUM
www.ti.com
13-Jun-2011
PACKAGING INFORMATION
Orderable Device
TUSB9261PVP
Status
(1)
ACTIVE
Package Type Package
Drawing
HTQFP
PVP
Pins
Package Qty
64
250
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAUAGLevel-4-260C-72 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated