Embedded Power for Business-Critical Continuity Rev. 2.18.09_133 HPS35 Series of 4 HPS35 Series 350 - 1400 Watts Total Power: Input Voltage: # of Outputs: 350 Watts per module 90-264 VAC Single and standby Electrical Specifications Input Special Features •Active Power Factor Correction •EN61000-3-2 compliant •CISPR22, EN55022 Level-B conducted/radiated EMI •EN61000 immunity standards •5Vsb@2A •Overvoltage protection (OVP) •Overcurrent protection (OCP) •Overtemperature protection (OTP) •AC OK signal and indicator LED •DC OK signal and indicator LED •Remote Inhibit •Remote Sense on main output • Hot Plug •N+1 Redundant •2 year warranty Input voltage: 90-264 VAC typical Frequency: 47-440 Hz Inrush current: 40 A peak typical @ 25 °C Efficiency: 80% typ @ full load, 230 VAC Power factor: 0.98 typical @ 115 VAC, full load Turn-on time: EMI filter standard: AC ON -2 sec., Inhibit / Enable 160 ms CISPR 22, EN55022 Level “B” Leakage current standard: <0.5 mA max @ 230 VAC @ 60Hz (per module) Radiated EMI: CISPR 22, EN55022 Level “B” Holdup time: 20 ms minimum (independent of input VAC) AC OK: 5 ms early warning minimum before outputs lose regulation Harmonic distortion: Isolation: Meets EN61000-3-2 Meets EN60950 Output Adjustability: ±5% of nominal output voltage Overall regulation: ±3% Ripple: Dynamic response: 1% of Vout pk - pk (20 MHz bandwidth) Recovery time: Overcurrent protection: To within 1% in <300 µsec 115 - 130% of rated output current Short circuit protection: Protected for continuous short circuit. Auto recovery. Overvoltage protection: 120 - 140% AC Reset. 4% from 25% to 75% load step Reverse voltage protection: 100% of rated output voltage Safety • UL • CSA • TUV • CB • CE UL60950-1, 1st Ed. (April 1, 2003) CSA C22.2 60950-1-03 EN60950-1:2001 (1st Ed.) IEC60950-1, 1st Ed. (2001) Mark (LVD) Thermal protection: Main and Aux disabled when internal temp exceeds safe operating range Remote sense: Up to 0.5 V total drop Single wire parallel: Current share to within 10% of total rated current on main output ±5% of nominal DC OK: Module Information Rev.2.18.09_133 HPS35 Series of 4 Environmental Specifications Operating temperature: 0 ° to 50 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C Shock: Operating: 4g, half sine, 22 ms minimum duration, all 6 faces Non-operating: 30g, half since, 6 ms minimum duration, all 6 faces Random Vibration: Operating: 1g rms, 20 min/axis Non-operating: 2.5g rms, 20 min/axis Humidity: Storage Temperature: 95% non-condensing -40 ° to +85 °C Temperature coefficient: 0.04% per °C Cooling Internal DC fans Ordering Information Modules +12V / 29A 350 90-264 HPS35 Volt Output Amps 12.0 29.2 24.0 14.6 48.0 7.3 1.6” x 4.3” x 10.5” 4 Unit Weight (lbs) 3.2 SERIAL NO.: OUTPUT: REV: XX A/C CODE: XXXX 73-811-029 50/60 Hz DATE: YYWW S/N: MMMMWWSSSSRRC MADE IN PHILIPPINES 90 - 240VAC - 40A HPS35L-NNR-000 INPUT: Watts Input Voltage Module ID Code L Q W Max. Size (H x W x L) Number per Rack 7.6 MAXIMUM OUTPUT POWER IS 350W 12V 24V 48V 53.8 HPS35L-NNR-000 HPS35Q-NNR-000 HPS35W-NNR-000 (All units in mm) Pin Assignments HPS35 Module Top TOP SIDE 1-24 Pin Description Pin Description PIN DESIGNATION PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 TOP 1 BOTTOM AC (L) 13 COMMON SIGNAL NAME PIN NO. SIGNAL NAME 2AC (L) BLANK A 14 AC (L) V OUT BLANK V OUT PIN NO. 3BLANK AC (N) B 15 AC (N) C AC (N) 14 4BLANK BLANK D 16 BLANK V OUT 15 GND V OUT 16 5GND GND E 17 SWP F -SENSE 17 65V RTN SWP H 18 V OUT +SENSE 18 COMMON 7COMMON5V RTNJ 19 V OUT 19 COMMON K COMMON 8COMMONCOMMON 20 BLANK 20 L COMMON 21 M COMMON 9COMMONCOMMON 21 +5 STANDBY 22 COMMON N COMMON 23 10 COMMON 22 TBA COMMON P COMMON 24 11 COMMON 12 COMMON 23 FAN MON 24 I2C CLK Bottom 1 2 AC D B TOP SIGNAL NAME C +12V D +12V E +12V +12V F +12V H +12V BLANK J +5V STANDBY K TBD FAN MON L I2C CLK M N A B Unit Connector 3 4 5 Description 6 7 8 9 10 11 12 13 Pin 14 15 16 Description 17 18 19 20 21 22 23 24 Pin E F H J K L M N P R S AC (L) P BLANK BOTTOM R AC (N) SIGNAL NAME S PIN NO. R +12V BLANK T S +12V GND T +12V U U +12V -SENSE V V +12V +SENSE W +12V W X INHIBIT X COMMON Y TBD COMMON Z AC OK Y AA COMMONDC OK Z AB I2C DATA COMMON AA COMMON AB T U V W X Y Z AA COMMON V OUT V OUT V OUT V OUT V OUT V OUT INHIBIT TBA AC OK DC OK I2C DATA Card Edge Connector with gold fingers double-sided 1.6mm FR-4 PCB AB Mating connector: EDAC 307-048-520-201 or equivalent Rating: 5A per contact Rack Information Rev. 2.18.09_133 HPS35 Series of 4 Racks HPR1-00 482.6 22.0 SERIAL NO.: 25.0 DATE: YYWW S/N: MMMMWWSSSSRRC MADE IN PHILIPPINES REV: XX A/C CODE: XXXX 73-810-002 50/60 Hz +12V / 29A 90 - 240VAC - 40A OUTPUT: INPUT: MAXIMUM OUTPUT POWER IS 1400W HPR1-00 1400 (fully populated) 90-264 HPS35 HPR1 1.75” x 19.0” x 13.0” (4 ea) HPS35 1U Unit Weight (lbs) 8.6 RTN 13.4 + Watts Input Voltage Module ID Rack ID Max. Size (H x W x L) Module Distribution Standard Size 468.8 343.2 31.7 442.0 330.2 RTN 43.7 + 3.2 AC Cord: (North America) For all other countries, please contact factory. 6.0 1 19 20 37 PIN DESIGNATION SLOT 1 6: INHIBIT 7: DC OK 8: AC OK 9: I2C Address #1 10: I2C Address #2 11: Fan Monitor 12: Global AC OK 1: 5V RTN (std-by) 2: (+) sense 3: (-) sense 4: 5V (std-by) 5: not used 20: I2C CLK 21: I2C DATA SLOT 2 13: INHIBIT 14: DC OK 15: AC OK 16: I2C Address 17: I2C Address 18: Fan Monitor 19: Global INHIBIT SLOT 3 24: INHIBIT 25: DC OK 26: AC OK 27: I2C Address 28: I2C Address 29: Fan Monitor 30: Not used SLOT 4 31: INHIBIT 32: DC OK 33: AC OK 34: I2C Address 35: I2C Address 36: Fan Monitor 37: Not used 22: SWP 23: Not used D-sub Connector Pin Outs Pin Description Pin Description S L O T 1 S L O T 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 5V Return (std-by) + Remote Sense - Remote Sense 5V Stand by Unused Module Inhibit DC OK AC OK I2C_ADD#1 I2C_ADD#2 Fan Monitor Global AC OK Module Inhibit DC OK AC OK I2C_ADD#1 I2C_ADD#2 Fan Monitor Global Inhibit S L O T 3 S L O T 4 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 I2C CLOCK I2C DATA SWP Unused (I2C_INT) Module Inhibit DC OK AC OK I2C_ADD#1 I2C_ADD#2 Fan Monitor Unused Module Inhibit DC OK AC OK I2C_ADD#1 I2C_ADD#2 Fan Monitor Unused 1) Quail Electronics Series 5050 or equivalent (15A/125V) Supply End - NEMA 5-15P Equipment End - IEC 60320-C19 2) Quail Electronics Series 5052 or equivalent (20A/125V) Supply End - NEMA 5-20P Equipment End - IEC60320-C19 Blank Panel: Astec P/N 73-686-000 PSU Connector 617-A-037-P-AJ-1-21 (Male socket) Amphenol Pin Out Diagram D-sub Connector (male) Mating Connector 617-A-037-S-AJ-1-20 (Female socket) Amphenol Pin Out Diagram D-sub Connector (female) Embedded Power for Business-Critical Continuity D. Sub Connector Additional Notes Pin 2 + Remote Sense Pin 3 - Remote Sense Compensates for up to 0.5V drop. Recommended shielded twisted wire pair. DC OK (OUT Signal) Pin 12 - Global AC OK (OUT signal) Note: DC OK signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin. Note: AC OK signals are OR’ed together AC OK (OUT Signal) internally. If any module fails, the LED on the affected module will be off and the logic signal will indicate AC NOT OK. Pin 19 - Global Inhibit (IN signal) Note: All outputs disabled when Pin 19 is open or High. Note: AC OK signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin. Hi state: Source 100uA @ 4V Pin 22 - SWP (IN/OUT signal) Low State: Sink 10mA @ 0.5V SWP Pin is used when PIN 22 connecting racks in Fan Monitor (OUT Signal) parallel to achieve current sharing. Current PIN 3 share accuracy is typically 10% of full load. Note: Module Inhibit signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin. 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone:+1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone:+44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone:+852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. Note: SWP Voltage is 5V at 100% load current. Module Inhibit (IN Signal) Americas Rev.2.18.09_133 HPS35 Series of 4 Note: Fan Monitor signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin. I2C_ADD#1 I2C_ADD#2 TBD AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.