SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER SEPTEMBER 2008 GENERAL DESCRIPTION The SP26LV432 is a quad differential line receiver with three-state outputs designed to meet the EIA specifications of the RS-422 serial protocol. The SP26LV432 features Exar's BiCMOS process allowing low power operational characteristics of CMOS technology while meeting all of the demands of the RS-422 serial protocol at 50Mbps under load. The RS-422 protocol allows up to 10 receivers to be connected to a multipoint bus transmission line. The SP26LV432 features a receiver enable control common to all four receivers and a high-Z output with 6mA source and sink capability. Since the cabling can be as long as 4,000 feet, the RS-422 receivers of the SP26LV432 are equipped with a wide (-7.0V to +7.0V) common-mode input voltage range to accommodate ground potential differences. REV. 1.0.0 FEATURES • Quad Differential Line Receivers • Compatible with the EIA standard for RS-422 serial protocol • High-Z Output Control • Switching Rates Up to 50Mbps • 14ns Typical Receiver Propagation Delays • 60mV Typical Input Hysteresis • Single +3.3V Supply Operation • Common Receiver Enable Control • 26LV32 industry standard footprint compatible • Ideal For Use with SP26LV431, Quad Drivers • -7.0V to +7.0V Common-Mode Input Voltage range FIGURE 1. TYPICAL APPLICATION CIRCUIT Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 FIGURE 2. PIN OUT ASSIGNMENT ORDERING INFORMATION PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE DEVICE STATUS SP26LV432CP-L 16-pin Plastic DIP 0°C to +70°C Active SP26LV432CN-L 16-pin Narrow SOIC 0°C to +70°C Active SP26LV432CN-L/TR 16-pin Narrow SOIC 0°C to +70°C Active SP26LV432EN-L 16-pin Narrow SOIC -40°C to +85°C Active SP26LV432EN-L/TR 16-pin Narrow SOIC -40°C to +85°C Active 2 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 PIN DESCRIPTIONS Pin Assignments PIN NUMBER PIN NAME TYPE DESCRIPTION 1 RI1B I Inverted RS-422 receiver input. 2 R1A I Non-inverted RS-422 Receiver input. 3 RO1 O TTL receiver output. 4 ENABLE I Receiver input enable, active HIGH. 5 RO2 O TTL receiver output. 6 RI2A I Non-inverted RS-422 Receiver input. 7 RI2B I Inverted RS-422 receiver input. 8 GND Pwr 9 RI3B I Inverted RS-422 receiver input. 10 RI3A I Non-inverted RS-422 Receiver input. 11 RO3 O TTL receiver output. 12 ENABLE I Receiver input enable, active LOW. 13 RO4 O TTL receiver output. 14 RI4A I Non-inverted RS-422 Receiver input. 15 RI4B I Inverted RS-422 receiver input. 16 VCC Pwr Ground. +3.0V to +3.6V power supply. Pin type: I=Input, O=Output. 3 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections to the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability and cause permanent damage to the device. VCC (Supply Voltage) 7.0V VCM (Common Mode Range) ±14V VDIFF (Differential Input Voltage) ±14V VIN (Enable Input Voltage) Vcc + 1.5V TSTG (Storage Temperature Range) -65°C to +150°C IO (Maximum Current Per Output) ±25mA Storage Temperature Range -65°C to + 150°C Power Dissipation 16-pin PDIP (derate 14.3mW/°C above +70°C) 1150mW Power Dissipation 16-pin NSOIC (derate 8.95mW/°C above +70°C) 725mW CAUTION: ESD (Electrostatic Discharge) sensitive device. Permanent damage may occur on unconnected devices subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts. Personnel should be properly grounded prior to handling this device. The protective foam should be discharged to the destination socket before devices are removed. ELECTRICAL CHARACTERISTICS UNLESS OTHERWISE NOTED: THE FOLLOWING SPECIFICATIONS APPLY FOR VCC = +3.0V TO +3.6V WITH TA = +25OC AND ALL MIN AND MAX LIMITS APPLY ACROSS THE RECOMMENDED OPERATING TEMPERATURE RANGE. SYMBOL VCC PARAMETERS Supply Voltage MIN. TYP. 3.0 Enable Input Rise or Fall Times MAX. UNITS 3.6 V 3 CONDITIONS ns Input Electrical Characteristics VTH Minimum Differential Input Voltage -200 50 +200 mV VOUT = VOH or VOL, -7V < VCM < +7V RIN Input Resistance 5.0 kΩ VIN = -7V, +7V, +10V Other input = GND IIN Input Current +1.25 +1.5 mA VIN = +10V, Other input = GND IIN Input Current -1.5V -2.5V mA VIN = -10V, Other input = GND VIH(EN) Minimum Enable HIGH Input Level Voltage VIL(EN) Maximum Enable LOW Input Level Voltage IEN VHYST ICC 2.0 V 0.8 V ±1.0 µA VIN = VCC or GND Input Hysteresis 60 mV VCM = 0V Quiescent Supply Current 5 mA VCC = +3.3V, VDIFF = +1V Maximum Enable Input Current 4 15 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 UNLESS OTHERWISE NOTED: THE FOLLOWING SPECIFICATIONS APPLY FOR VCC = +3.0V TO +3.6V WITH TA = +25OC AND ALL MIN AND MAX LIMITS APPLY ACROSS THE RECOMMENDED OPERATING TEMPERATURE RANGE. SYMBOL PARAMETERS MIN. TYP. 2.4 2.8 MAX. UNITS CONDITIONS Output Electrical Characteristics VOH Minimum HIGH Level Output Voltage V VCC = +3.0V, VDIFF = +1V, IOUT = -6mA VOL Maximum LOW Level Output Voltage 0.2 0.5 V VCC = +3.0V, VDIFF = -1V, IOUT = +6mA IOZQ Maximum Tri-State Output Leakage Current ±0.5 ±5.0 µA VOUT = VCC or GND, ENABLE = VIL , ENABLE = VIH Switching Characteristics tPLH, tPHL Propagation Delays 14 35 ns CL = 50pF, VDIFF = 2.5V, VCM = 0V, VCC = +3.3V tRISE, tFALL Output Rise and Fall Times 5 10 ns CL = 50pF, VDIFF = 2.5V, VCM = 0V, VCC = +3.3V tPZH, tPZL Output Enable Time 40 ns CL = 50pF, RL = 1000Ω, VDIFF = 2.5V, VCC = +3.3V tPHZ, tPLZ Output Disable Time 40 ns CL = 50pF, RL = 1000Ω, VDIFF = 2.5V, VCC = +3.3V 5 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 3. SP26LV432 BLOCK DIAGRAM FIGURE 4. PROPAGATION DELAY 6 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 5. TEST CIRCUIT FOR HIGH-Z OUTPUT TIMING FIGURE 6. HIGH IMPEDANCE OUTPUT ENABLE AND DISABLE WAVEFORMS 7 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 7. DIFFERENTIAL PROPAGATION DELAY VS TEMPERATURE FIGURE 8. DIFFERENTIAL PROPAGATION DELAY VS SUPPLY VOLTAGE 8 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 9. DIFFERENTIAL SKEW VS TEMPERATURE FIGURE 10. DIFFERENTIAL SKEW VS SUPPLY VOLTAGE 9 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 11. HIGH OUTPUT VOLTAGE VS CURRENT OVER TEMPERATURE FIGURE 12. HIGH OUTPUT VOLTAGE VS CURRENT OVER SUPPLY VOLTAGE 10 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 13. LOW OUTPUT VOLTAGE VS CURRENT OVER TEMPERATURE FIGURE 14. LOW OUTPUT VOLTAGE VS CURRENT OVER SUPPLY VOLTAGE 11 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 15. INPUT RESISTANCE VS INPUT VOLTAGE FIGURE 16. INPUT CURRENT VS SUPPLY VOLTAGE 12 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 17. TRANSITION VOLTAGE VS TEMPERATURE FIGURE 18. TRANSITION VOLTAGE VS SUPPLY VOLTAGE 13 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 19. SUPPLY CURRENT VS TEMPERATURE FIGURE 20. DISABLED SUPPLY CURRENT VS SUPPLY VOLTAGE 14 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER FIGURE 21. SUPPLY CURRENT VS DATA RATE 15 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 1.0 PRODUCT DESCRIPTION The SP26LV432 is a low-power quad differential line receiver designed for digital data transmission meeting the specifications of the EIA standard RS-422 serial protocol. The SP26LV432 features Exar's BiCMOS process allowing low power operational characteristics of CMOS technology while meeting all of the demands of the RS-422 serial protocol up to 50Mbps under load in harsh environments. The RS-422 standard is ideal for multi-drop applications and for long-distance communication. The RS-422 protocol allows up to 10 receivers to be connected to a data bus, making it an ideal choice for multi-drop applications. Since the cabling can be as long as 4,000 feet, RS-422 Receivers have an input sensitivity of 200mV over the wide (-7.0V to +7.0V) common mode range to accommodate ground potential differences. Internal pull-up and pull-down resistors prevent output oscillation on unused channels. Because the RS-422 is a differential interface, data is virtually immune to noise in the transmission line. The SP26LV432 accepts RS-422 levels and translates these into TTL or CMOS output levels. The SP26LV432 features active HIGH and active LOW receiver enable controls common to all four receiver channels see Table 1. A logic HIGH on the ENABLE pin (pin 4) or a logic LOW on the ENABLE pin (pin 12) will enable the receiver outputs. A logic LOW on the ENABLE pin (pin 4) and a logic HIGH on the ENABLE pin (pin 12) will force the receiver outputs into high impedance (high-Z). Refer to the truth table in Table 1. The RS-422 line receivers feature high source and sink current capability. All receivers are internally protected against short circuits on their inputs. The receivers feature tri-state outputs with 6mA source and sink capability. The typical receiver propagation delay is 14ns (35ns max). To minimize reflections, the multipoint bus transmission line should be terminated at both ends in its characteristic impedance, and stub lenghts off the main line should be kept as short as possible. 16 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 FIGURE 22. TWO-WIRE BALANCED SYSTEM, RS-422 TABLE 1: TRUTH TABLE, ENABLE/DISABLE FUNCTION COMMON TO ALL FOUR RS-422 RECEIVERS ENABLE ENABLE INPUT OUTPUT LOW HIGH don’t care high-Z HIGH don’t care VID ≥ VTH (max) HIGH HIGH don’t care VID ≤ VTH (min) LOW don’t care LOW VID ≥ VTH (max) HIGH don’t care LOW VID ≤ VTH (min) LOW HIGH don’t care Open HIGH don’t care LOW Open HIGH 17 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER p PACKAGE DIMENSIONS (16 PIN NSOIC) 18 REV. 1.0.0 SP26LV432 REV. 1.0.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER PACKAGE DIMENSIONS (16 PIN PDIP) 19 SP26LV432 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER REV. 1.0.0 REVISION HISTORY DATE REVISION DESCRIPTION 3/08/04 A Production Release. 3/08/04 B Include tape and reel p/n’s. 4/17/06 C Fixed Truth Table typo page 1 9/05/08 1.0.0 Converted to Exar standard datasheet format. Added Ordering Information for -40C to +85C operating temperature range NSOIC package. Changed revision to 1.0.0. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2008 EXAR Corporation Datasheet September 2008. Send your UART technical inquiry with technical details to hotline: [email protected]. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 20