User's Guide Heavy Duty Meter Model 407026 Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment (a six month limited warranty applies on sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied. Introduction Congratulations on your purchase of the Extech Heavy Duty Light Meter. This light meter offers selectable lighting types, data record/recall, relative display mode, and PC interface. This professional meter, with proper care, will provide years of safe reliable service. 2 Model 407026 Version 2.3 January 2004 Specifications General Specifications Circuit Custom one-chip LSI microprocessor circuit Display 3-1/2 digit (2000 count) LCD display with contrast adjustment Measurement ranges LUX: 0 to 50,000 LUX (3 range); Fc: 0 to 5000 Fc (3 range); Relative mode: 0 to 1999% Data Hold Freezes displayed reading Lighting Types Sodium, Daylight/Tungsten, Fluorescent and Mercury Sensor Structure Cosine/color corrected photo-diode meets C.I.E. Memory Store/Recall Records/Recalls Max/Min/Avg readings Sample rate 0.4 seconds (approx.) per reading Zero Adjust Push-button procedure Auto Power Off After approx. 10 minutes Data Output RS-232 PC serial interface (optional software/cable PN 407001) Operating conditions 32 °F to 122 °F (0 °C to 50 °C); <80% RH Power Supply 9V battery Power consumption Approx. 5 mA DC. (approx. 200 hr battery life) Weight 0.71 lbs. (320 g) Dimensions Instrument: 7.1 x 2.8 x1.3" (180 x 72 x 32 mm) Sensor: 3.3 x 2.2 x 0.7" (85 x 55 x 17.5 mm) Range Specifications Measurement LUX Foot Candles Relative mode Range 2,000 LUX Display 0-1,999 LUX Resolution 1 LUX 20,000 LUX 1,800-19,990 LUX 10 LUX 50,000 LUX 18,000-50,000 LUX 100 LUX 200 Fc 0-186.0 Fc 0.1 Fc 2,000 Fc 167-1,860 Fc 1 Fc 5,000 Fc 1,670-5,000 Fc 0-1999% Accuracy ± (4% + 2 digits) of full scale 10 Fc 1% Note: The accuracy specification above applies to calibration performed using a precision O standard incandescent tungsten light source of 2856 K with meter on the tungsten setting. 3 Model 407026 Version 2.3 January 2004 Meter Description 1 LCD Display 2 Keypad 3 Light sensor 4 Battery compartment (rear) 5 Sensor input 6 RS-232 PC Interface jack 7 Protective Holster 8 LCD Contrast Adjust 6 5 7 1 8 2 4 3 4 Model 407026 Version 2.3 January 2004 Operation Meter Power and Automatic Power Off 1. Press the POWER button to turn the meter on. If the display does not switch on, check the 9V battery. 2. Press the POWER button again to turn the meter off. 3. The meter has an automatic power off feature that conserves battery energy. After 10 minutes the meter automatically shuts off. To defeat this feature, press the RECORD button to put the meter in the recording mode. Display ZERO Calibration Please perform a zero calibration before each use. This will ensure the highest accuracy. 1. Place the sensor cover over the light sensor, effectively blocking all light to the sensor. 2. Select the 2,000 LUX range using the RANGE switch. 3. Press the ZERO button. The reading should be zero. 4. Remove the sensor cover from the light sensor and proceed. Selecting the unit of measure Press the LUX/Fc button to select the desired unit of measure. The display icons will reflect the current setting. Selecting a light source Select the type of lighting to be measured by pressing the LIGHT SOURCE button. The display will indicate the lighting type icon (see icon list below). L = Tungsten/Daylight (use this setting when calibrating with a Tungsten lamp) F = Fluorescent S = Sodium C = Mercury Note: For Halogen and Metal Halide light use the Tungsten setting Taking Measurements Hold the light sensor in the area where light is to be collected. The light being measured must encompass the entire surface of the light sensor dome (pin point lighting such as with LED light cannot be measured). The display will indicate the light intensity value in LUX or Foot candles (Fc). Note that since the main display area is limited to a reading of ‘1999’, the right-most digit in the 20,000 LUX and 5,000 Fc ranges appears on the lower LCD line. In the 50,000 LUX range, the last two digits appear on the lower LCD line It may be necessary to adjust the display contrast due to a change in viewing angle or voltage drift. Use the LCD Contrast adjustment located on the right side of the meter to set the preferred contrast. Display Range Selection Take a measurement starting at the highest range and then work down using the RANGE switch. If the display shows dashes along the top of the reading area ( ), the input exceeds the maximum value for the selected range; select a higher range. If the display shows dashes along the bottom of the reading area ( ), the input is too low; select a lower range. 5 Model 407026 Version 2.3 January 2004 Data Hold While measuring, press the HOLD button to freeze the reading. The LCD will display D.H. indicating that the Data Hold function is engaged. Press HOLD again to return to normal operation. Relative % Mode In the RELATIVE mode of operation, the meter displays light level as a comparison to a reference value. The reference value is stored by pressing the ‘%’ button while the desired light level reference is on the display. When the button is pressed, ‘100%’ will be displayed and the ‘%’ icon will appear. After the ‘%’ button is pressed, light measurements will be displayed as a percentage of the reference value. For example, if the light level reference is 1000 LUX, a display of 500 LUX will be represented as 50%. Further, a light level of 250 LUX will display as 25%. Use the equation below: Light measurement Display % = --------------------------------------------------------------------------- X 100 Stored reference light measurement Press the ‘%’ button again to return to normal operation. Maximum (MAX), Minimum (MIN), and Average (AVG) readings The meter can keep track of the highest, lowest, and average readings for later recall. 1. Press the RECORD button to start tracking the MAX, MIN, and AVG readings. The REC display will switch on. 2. When desired, press the RECALL button. 3. The MAX display icon appears next to the REC display icon. The reading shown is the highest reading encountered since the RECORD button was pressed. 4. Press RECALL twice more to view the MIN and AVG readings. 5. Press the RECORD button to return to normal operation. RS-232 PC Interface This meter is equipped with a RS-232 serial data port. This interface is for use with the Extech Data Acquisition Software (Part number 407001) and enables the user to capture, store and display readings on a PC. Contact Extech or refer to the 407001 user manual for details on the PC interface. Battery Replacement When the low battery indicator appears (LBT), replace the battery as soon as possible. Reliable readings can be obtained for several hours after the first appearance of the low battery indication. To replace the battery: 1. Remover the meter's rubber protective holster. 2. The battery compartment is located on the lower back of the meter. Pry the battery compartment cover off using a small coin or screwdriver and remove the battery. 3. Replace the 9V battery and reinstall the cover. 4. Ensure that the battery cover is secured after replacing the battery. 6 Model 407026 Version 2.3 January 2004 Typical Light Levels Lux Foot Candles 20-75 2-7 75-150 7-15 Lux Foot Candles Emergency Stairs, Warehouse 100-150 10-15 Washing Exit/Entrance Passages 150-200 15-20 Recreational Activities Drawing Room, Table Factories Home 150-300 15-30 Packing Work 200-300 20-30 300-750 30-75 Visual Work: Production Line 300-500 30-50 Makeup 750-1,500 75-150 Typesetting: Inspection Work 500-1,500 50-150 Reading, Study 1,5003,000 150-300 Electronic Assembly, Drafting 1,000-2,000 100-200 75-100 7-10 Office Sewing Restaurant Indoor Emergency Stairs 75-150 7-15 Corridor Stairs 100-200 10-20 Corridor Stairs 150-300 15-30 Entrance, Wash Room 200-750 20-75 Conference, Reception Room 300-750 30-75 Cooking\Dinning Room 750-1,500 75-150 Clerical Work 750-1,500 75-150 Show Window 1,5002,000 150-2000 Typing, Drafting 75-150 7-15 Indoors 30-75 3-7 Emergency Stairs Store Hospital 150-200 15-20 Corridor/Stairs 75-100 7-10 Stairs 200-300 20-30 Reception 100-150 10-15 Sick Room, Warehouse 300-500 30-50 Display Stand 150-200 15-20 Waiting Room 500-750 50-75 Elevator 200-750 20-75 Medical Exam Room 750-1,500 75-150 Show Window, Packing Table 750-1,500 75-150 Operating Room 1,5003,000 150-300 Storefront, Show Window 5,00010,000 500-1000 Eye Inspection Common Conversion Factors 1 lm/m2 = Illuminance (Visible Flux Density) 1 lux (lx) 10-4 lm/cm2 10-4 phot (ph) 9.290 x 10-2 lm/ft2 9.290 x 10-2 foot-candles 2 1 lm/m /sr = 1 candela/m2 1 lm/sr = 1 candella 1 lumen (lm) = 1.464 x 10-3 watts @ 555 nm Luminance (Visible Flux Density per Solid Angle) Luminous Intensity (Visible Flux per Solid Angle) Luminous Flux ( Visible Flux) 7 Model 407026 Version 2.3 January 2004 Calibration and Repair Services Extech offers repair and calibration services for the products we sell. Extech also provides NIST certification for most products. Call the Customer Service Department for information on calibration services available for this product. Extech recommends that annual calibrations be performed to verify meter performance and accuracy. Support Hotline (781) 890-7440 Tech support: Ext. 200; Email: [email protected] Repair/Returns: Ext. 210; Email: [email protected] Website: www.extech.com Copyright © 2004 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form. 8 Model 407026 Version 2.3 January 2004