FERROXCUBE DATA SHEET P14/8 P cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube P cores and accessories P14/8 CORE SETS Effective core parameters SYMBOL PARAMETER VALUE Σ(I/A) core factor (C1) 0.789 mm−1 Ve effective volume 495 mm3 Ie effective length 19.8 mm Ae effective area 25.1 mm2 Amin minimum area 19.8 mm2 m mass of set ≈ 3.2 g 9.5 handbook, halfpage UNIT 11.6 0.3 0.4 0 6 2.7 1.2 0 0.4 0.2 0 0 0 14.3 0.2 0.5 O 3.1 0.1 0.4 0.1 5.6 0 8.4 0.2 1.2 0.15 MGC164 M1.7 Dimensions in mm. Fig.1 P14/8 core set. Core sets for filter applications Clamping force for AL measurements, 60 ±20 N. GRADE 3D3 3H3 AL (nH) TOTAL AIR GAP (µm) TYPE NUMBER (WITH NUT) TYPE NUMBER (WITHOUT NUT) 40 ± 3% ≈ 25 ≈ 1170 P14/8-3D3-E40/N P14/8-3D3-E40 63 ± 3% ≈ 40 ≈ 650 P14/8-3D3-E63/N P14/8-3D3-E63 P14/8-3D3-E100/N P14/8-3D3-E100 − P14/8-3D3 100 ± 3% ≈ 63 ≈ 360 1000 ± 25% ≈ 630 ≈0 160 ± 3% ≈ 100 ≈ 220 P14/8-3H3-A160/N P14/8-3H3-A160 250 ± 3% ≈ 157 ≈ 130 P14/8-3H3-A250/N P14/8-3H3-A250 315 ± 3% ≈ 198 ≈ 100 P14/8-3H3-A315/N P14/8-3H3-A315 400 ± 3% ≈ 251 ≈ 75 P14/8-3H3-A400/N P14/8-3H3-A400 ≈ 1350 ≈0 − P14/8-3H3 2150 ± 25% 2008 Sep 01 µe 949 Ferroxcube P cores and accessories P14/8 Core sets for general purpose transformers and power applications Clamping force for AL measurements, 60 ±20 N. GRADE 3C81 3C91 3F3 AL (nH) AIR GAP (µm) µe TYPE NUMBER 63 ± 3% ≈ 40 ≈ 680 P14/8-3C81-E63 100 ± 3% ≈ 63 ≈ 390 P14/8-3C81-A100 160 ± 3% ≈ 100 ≈ 220 P14/8-3C81-A160 250 ± 3% ≈ 157 ≈ 130 P14/8-3C81-A250 315 ± 3% ≈ 198 ≈ 100 P14/8-3C81-A315 2800 ± 25% ≈ 1 760 ≈0 2800 ± 25% P14/8-3C81 ≈ 1 760 ≈0 63 ± 3% ≈ 40 ≈ 680 P14/8-3F3-E63 100 ± 3% ≈ 63 ≈ 390 P14/8-3F3-A100 P14/8-3C91 160 ± 3% ≈ 100 ≈ 220 P14/8-3F3-A160 250 ± 3% ≈ 157 ≈ 130 P14/8-3F3-A250 315 ± 3% ≈ 198 ≈ 100 P14/8-3F3-A315 ≈ 1 260 ≈0 2000 ± 25% P14/8-3F3 Core sets of high permeability grades Clamping force for AL measurements, 60 ±20 N. GRADE 3E27 AL (nH) µe AIR GAP (µm) 5750 ± 25% ≈ 3610 ≈0 TYPE NUMBER P14/8-3E27 Properties of core sets under power conditions B (mT) at CORE LOSS (W) at H = 250 A/m; f = 25 kHz; T = 100 °C f = 25 kHz; ˆ = 200 mT; B T = 100 °C f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C 3C81 ≥320 ≤ 0.1 − − − 3C91 ≥315 − 3F3 ≥315 − GRADE ≤ ≤ 0.06 Note 1. Measured at 60 °C. 2008 Sep 01 0.03(1) 950 ≤ 0.22 (1) − − ≤ 0.1 Ferroxcube P cores and accessories P14/8 INDUCTANCE ADJUSTERS General data PARAMETER SPECIFICATION Material of head and thread polypropylene (PP), glass fibre reinforced Maximum operating temperature 125 °C O 3.13 handbook, halfpage 0.07 0 6.7 2.95 M 1.7 0.7 2.4 min MGC165 Dimensions in mm. Fig.2 P14/8 inductance adjuster. Inductance adjuster selection chart GRADE 3H3 AL (nH) 100 ∆L/L(1) TYPES FOR MEDIUM ∆L/L(1) ADJUSTMENT − − ADJ-P14-ORANGE − TYPES FOR LOW ADJUSTMENT 14 TYPES FOR HIGH ADJUSTMENT − ∆L/L(1) − − ADJ-P14-WHITE 17 250 ADJ-P14-WHITE 10 ADJ-P14-BROWN 15 − 315 ADJ-P14-WHITE 8 − − − 400 ADJ-P14-BROWN 9 − − − − 630 ADJ-P14-BROWN 4 − − − − − − − ADJ-P14-ORANGE 24 ADJ-P14-ORANGE 20 160 3D3 (applies to all types) 40 63 100 − − ADJ-P14-ORANGE − − − 11 − − Note 1. Maximum adjustment range. 2008 Sep 01 951 ADJ-P14-BROWN − 24 − − − Ferroxcube P cores and accessories P14/8 COIL FORMERS General data for CP-P14/8 coil former PARAMETER SPECIFICATION Coil former material polybutyleneterephtalate (PBT), glass reinforced, flame retardant in accordance with “UL 94V-0”; UL file number E45329 (R) Maximum operating temperature 155 °C, “IEC 60085”, class F 0 5.4 −0.2 handbook, full pagewidth 0.4 0.3 0 0 7.1 −0.15 11.5 −0.2 2.2 6.1 +0.2 0 0.5 CBW601 0.4 Dimensions in mm. Fig.3 Coil former CP-P14/8. Winding data and area product for CP-P14/8 coil former NUMBER OF SECTIONS WINDING AREA (mm2) MINIMUM WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 8.8 4.1 28.9 221 CP-P14/8-1S 2 2 × 4.0 2 × 1.85 28.9 2 x 100 CP-P14/8-2S 2008 Sep 01 952 TYPE NUMBER Ferroxcube P cores and accessories P14/8 General data for CP-P14/8-A coil former PARAMETER SPECIFICATION Coil former material acetal (POM), glass reinforced, flame retardant in accordance with “UL 94-HB”; UL file number E66288(R) Maximum operating temperature 155 °C, “IEC 60085”, class F 6.1 min 5.5 max 1.9 min 7.1 11.55 max MGB529 Dimensions in mm. Fig.4 Coil former CP-P14/8-A. Winding data and area product for CP-P14/8-A coil former NUMBER OF SECTIONS MINIMUM WINDING AREA (mm2) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 9.4 4.5 29.0 236 CP-P14/8-1S-A TYPE NUMBER 2 2 x 4.32 2 x 2.0 29.0 2 x 108 CP-P14/8-2S-A 3 3 × 2.19 3 × 1.2 29.0 3 x 55.0 CP-P14/8-3S-A 2008 Sep 01 953 Ferroxcube P cores and accessories P14/8 General data 4-pins P14/8 coil former for PCB mounting PARAMETER SPECIFICATION Coil former material polyamide (PA6.6), glass reinforced, flame retardant in accordance with “UL 94V-0”; UL file number E41938(M) Maximum operating temperature 130 °C, “IEC 60085” , class B Pin material copper-zinc alloy (CuZn), tin (Sn) plated Resistance to soldering heat “IEC 60068-2-20”, Part 2, Test Tb, method 1B, 350 °C, 3.5 s Solderability “IEC 60068-2-20”, Part 2, Test Ta, method 1, 235 °C, 2 s 5.4 max. 3.55 handbook, full pagewidth 4.45 0.75 2 19 11.55 6 max. max. min. 7.1 16.1 2.4 4.75 ± 0.25 6.1 max. 6.8 max. CBW106 Dimensions in mm. Fig.5 P14/8 coil former for PCB mounting; 4-pins. Winding data and area product for 4-pins P14/8 coil former for PCB mounting NUMBER OF SECTIONS MINIMUM WINDING AREA (mm2) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) LENGTH OF PINS (mm) AREA PRODUCT Ae x Aw (mm4) 1 8.65 4.4 29.0 4.75 217 CPV-P14/8-1S-4SPD 1 8.65 4.4 29.0 6.8 217 CPV-P14/8-1S-4SPDL 2 2 × 3.87 2 × 2.0 29.0 4.75 2 x 97.1 CPV-P14/8-2S-4SPD 2 2 × 3.87 2 × 2.0 29.0 6.8 2 x 97.1 CPV-P14/8-2S-4SPDL 2008 Sep 01 954 TYPE NUMBER Ferroxcube P cores and accessories P14/8 General data 6-pins P14/8 coil former for PCB mounting PARAMETER SPECIFICATION Coil former material polyamide (PA6.6), glass reinforced, flame retardant in accordance with “UL 94V-0”; UL file number E41938(M) Maximum operating temperature 130 °C, “IEC 60085” , class B Pin material copper-zinc alloy (CuZn), tin (Sn) plated Resistance to soldering heat “IEC 60068-2-20”, Part 2, Test Tb, method 1B, 350 °C, 3.5 s Solderability “IEC 60068-2-20”, Part 2, Test Ta, method 1, 235 °C, 2 s 5.4 max. 7.1 handbook, full pagewidth 4.45 0.75 2 19 11.55 6 max. max. min. 7.11 max. 16.3 2.4 4.35 min. 10.2 max. 6.85 max. CBW107 Dimensions in mm. Fig.6 P14/8 coil former for PCB mounting; 6-pins. Winding data and area product for 6-pins P14/8 coil former for PCB mounting NUMBER OF SECTIONS MINIMUM WINDING AREA (mm2) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) LENGTH OF PINS (mm) AREA PRODUCT Ae x Aw (mm 4) 1 8.65 4.4 29.0 4.4 217 CPV-P14/8-1S-6PD 1 8.65 4.4 29.0 6.8 217 CPV-P14/8-1S-6PDL 2 2 × 3.87 2 × 2.0 29.0 4.4 2 x 97.1 CPV-P14/8-2S-6PD 2 2 × 3.87 2 × 2.0 29.0 6.8 2 x 97.1 CPV-P14/8-2S-6PDL 2008 Sep 01 955 TYPE NUMBER Ferroxcube P cores and accessories P14/8 MOUNTING PARTS General data for mounting parts ITEM Tag plate REMARKS FIGURE material: phenolformaldehyde (PF), glass reinforced TYPE NUMBER 7 TGP-P14/8-C 8 CON-P14/8 9 SPR-P14/8 flame retardant: in accordance with “UL 94V-0” ; UL file number E41429 maximum operating temperature: 180 °C, “IEC 60085”, class H pins: copper-tin alloy (CuSn), tin (Sn) plated resistance to soldering heat in accordance with “IEC 60 068-2-20”, Part 2, Test Tb, method 1B: 350 °C, 3.5 s solderability in accordance with “IEC 60068-2-20”, Part 2, Test Ta, method 1: 235 °C, 2 s Container copper-zinc alloy (CuZn), tin (Sn) plated earth pins: presoldered Spring CrNi-steel Clamp spring steel, tin-plated 10 CLM/TP-P14/8 Washer phenolformaldehyde (PF) 11 WAS-CLM/TP-P14/8 spring force: ≈60 N when mounted 2.54 2.1 5.08 1.5 mark 3.5 10.16 5.08 ∅0.8 15.7 max. 6 Dimensions in mm. Fig.7 Tag plate: TGP-P14/8-C. 2008 Sep 01 956 1.3 +0.15 0 CBW602 Ferroxcube P cores and accessories P14/8 handbook, full pagewidth 4.5 mark 0.6 5 1 8 15.6 max. 9.45 max. CBW422 Dimensions in mm. Fig.8 Container: CON-P14/8. 1.3 handbook, halfpage +0.3 0 13.4 max MGC169 Dimensions in mm. Fig.9 Spring: SPR-P14/8. 2008 Sep 01 957 Ferroxcube P cores and accessories P14/8 handbook, halfpage handbook, halfpage 9.4 13.2 9.27 ± 0.05 13 4 0.38 ± 0.08 0 13.7 − 0.13 9.65 MGB604 MBG174 Dimensions in mm. Dimensions in mm. Fig.10 Clamp: CLM/TP-P14/8. 2008 Sep 01 Fig.11 Washer: WAS-CLM/TP-P14/8. 958 Ferroxcube P cores and accessories P14/8 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 959