TI SMJ320C40KGDD

SGUS052 − APRIL 2004
D SMJ: QML Processing to MIL−PRF−38535
D Operating Temperature Ranges:
D
D
D
D
D
D
D
D
D
D
− Military (M) −55°C to 125°C
− Commercial (C) −25°C to 85°C
− Commercial (L) 0°C to 70°C
Highest Performance Floating-Point Digital
Signal Processor (DSP)
− C40-50:
40-ns Instruction Cycle Time:
50 MFLOPS, 25 MIPS, 275 MOPS,
320 MBps
− C40-40:
50-ns Instruction Cycle Time:
40 MFLOPS, 20 MIPS, 220 MOPS,
256 MBps
Six Communications Ports
6-Channel Direct Memory Access (DMA)
Coprocessor
Single-Cycle Conversion to and From
IEEE-745 Floating-Point Format
Single Cycle 1/x, 1/ Ǹ x
Source-Code Compatible With SMJ320C30
Validated Ada Compiler
Single-Cycle 40-Bit Floating-Point,
32-Bit Integer Multipliers
12 40-Bit Registers, 8 Auxiliary Registers,
14 Control Registers, and 2 Timers
IEEE Standard 1149.1† Test-Access Port
(JTAG)
D Two Identical External Data and Address
D
D
D
Buses Supporting Shared Memory Systems
and High Data-Rate, Single-Cycle
Transfers:
− High Port-Data Rate of 100 MBytes/s
(Each Bus)
− 16G-Byte Continuous
Program/Data/Peripheral Address Space
− Memory-Access Request for Fast,
Intelligent Bus Arbitration
− Separate Address-, Data-, and
Control-Enable Pins
− Four Sets of Memory-Control Signals
Support Different Speed Memories in
Hardware
Fabricated Using Enhanced Performance
Implanted CMOS (EPIC) Technology by
Texas Instruments (TI)
Separate Internal Program, Data, and DMA
Coprocessor Buses for Support of Massive
Concurrent Input/Output (I/O) of Program
and Data Throughput, Maximizing
Sustained Central Processing Unit (CPU)
Performance
On-Chip Program Cache and
Dual-Access/Single-Cycle RAM for
Increased Memory-Access Performance
− 512-Byte Instruction Cache
− 8K Bytes of Single-Cycle Dual-Access
Program or Data RAM
− ROM-Based Bootloader Supports
Program Bootup Using 8-, 16-, or 32-Bit
Memories Over Any One of the
Communications Ports
description
The SMJ320C40KGD DSP is a 32-bit, floating-point processor manufactured in 0.72-µm, double-level metal
CMOS technology. It is the fourth generation of DSPs from Texas Instruments, and it is the world’s first DSP
designed for parallel processing. The on-chip parallel processing capabilities of the C40 make the floating-point
performance required by many applications achievable and cost-effective.
The SMJ320C40 is the first DSP with on-chip communication ports for processor-to-processor communication
using simple communication software with no external hardware. This allows connectivity with no external glue
logic. The communication ports remove I/O bottlenecks, and the independent smart-DMA coprocessor is able
to handle the CPU I/O requirements.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
† IEEE Standard 1149.1−1990 Standard Test-Access Port and Boundary-Scan Architecture
EPIC and TI are trademarks of Texas Instruments Incorporated.
Copyright  2004, Texas Instruments Incorporated
! " #$%! " &$'(#! )!%*
)$#!" # ! "&%##!" &% !+% !%" %," "!$%!"
"!)) -!.* )$#! &#%""/ )%" ! %#%""(. #($)%
!%"!/ (( &%!%"*
POST OFFICE BOX 1443
&)$#!" #&(! ! 0112 (( &%!%" % !%"!%)
$(%"" !+%-"% !%)* (( !+% &)$#!"2 &)$#!
&#%""/ )%" ! %#%""(. #($)% !%"!/ (( &%!%"*
• HOUSTON, TEXAS 77251−1443
1
SGUS052 − APRIL 2004
description (continued)
The features of the communication ports are:
D Six communication ports for direct interprocessor communication and processor I/O
D 20 MBps bidirectional interface on each communication port for high-speed and low-cost multiprocessor
interface
D Separate input and output first-in, first-out (FIFO) buffers for I / O and processor-to-processor
communication
D Automatic arbitration and handshaking for direct processor-to-processor connection
The DMA coprocessor allows concurrent I/O and CPU processing for superior sustained CPU performance.
The key features of the DMA coprocessor:
D Link pointers that allow DMA channels to auto-initialize
D Parallel CPU operation and DMA transfers
D Six DMA channels support communication-port-to-memory data transfers
The SMJ320C40KGD CPU is configured for high-speed internal parallel processing. The key features of the
CPU are:
D Eight operations / cycles
D
D
D
D
−
40- / 32-bit floating-point / integer multiply
−
40-/32-bit floating-point / integer arithmetic and logic unit (ALU) operation
−
Two data accesses
−
Two address-register updates
IEEE floating-point conversion
Division and square-root support
C30 assembly language compatibility
Byte and halfword accessibility
Key factors in a parallel-processing implementation are the development tools that are available. The C40 is
supported by a host of parallel-processing development tools for developing and simulating code and for
debugging parallel-processing systems. The code generation tools include:
D Optimizing ANSI C compiler with a runtime library that supports use of communication ports and DMA
D SPOX, by Spectron Microsystems Incorporated, which provides parallel processing support as well as
DMA and communication port drivers
D Assembler and linker with support for mapping program and data to parallel processors.
SPOX is a trademark of Spectron Microsystems, Inc.
2
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS052 − APRIL 2004
description (continued)
The simulation tools include:
D Parallel DSP system-level simulation, by Logic Modeling Corporation (LMC), which includes a hardware
verification (HV) model and a full functional (FF) model
D TI software simulator with high-level language debugger interface for simulating a single processor
The hardware development and verification tools include:
D Parallel processor in-circuit emulator and high-level language debugger: XDS510
D Parallel processor development system with four TMS320C40s, local and global memory, and
communication port connections
For additional information when designing for cold temperature operation, please see Texas Instruments
application report 320C3x, 320C4x and 320MCM42x Power-up Sensitivity at Cold Temperature, literature
number SGUA001.
known good die technology
Known good die (KGD) options are offered for use in multichip modules and chip-on-board (COB) applications.
There is currently one verification technology used at TI to support KGD requirements for the SMJ320C40KGD:
Hot Chuck Probe.
electrical specifications
For military electrical and timing specifications, please refer to the SMJ320C40 Digital Signal Processor data
sheet, literature number SGUS017. For commercial electrical and timing specifications, see the TMS320C40
Digital Signal Processor Data Sheet, literature number SPRS038.
XDS510 is a trademark of Texas Instruments Incorporated.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
3
SGUS052 − APRIL 2004
SMJ
PREFIX
SMJ =
TMP =
320
C
40
KGD
M
50
C
T
KGD OPTION
T = TWB process
blank = HCP
MIL-PRF-38535 Processing
Commercial Level
DIE REVISION
C = Revision 5.2
D = Revision 7.0
DEVICE FAMILY
320 = DSP Family
SPEED RANGE
40 = 40 MHz
50 = 50 MHz
TECHNOLOGY
C = CMOS
TEMPERATURE RANGE
M (Military)
= −55°C to 125°C
L (Commercial) =
0°C to 70°C
DEVICE
40 = Floating-Point DSP
PACKAGE TYPE
KGD = Known Good Die
Figure 1. TMP / SMJ320C40KGD Device Nomenclature
JEDEC STANDARD
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
4
Die thickness is approximately 15 mils ± 1 mil.
Backside surface finish is silicon.
Maximum allowable die junction operating temperature is 175°C.
Glassivation material is compressive nitride.
Bond pad metal is composed of copper-doped aluminum.
Percent defective allowed for burned-in die is 5.
Life test data is available.
Configuration control notification.
Group A attribute summary is available (SMJ only).
Suggested die-attach material is silver glass (QMI 2569F).
Suggested bond wire size is 1.25 mil.
ESD rating is Class II.
Maximum allowable peak process temperature for die-attach is 440°C ± 5°C (for QMS2569F)
Saw kerf is dependent on blade size used.
Die backside potential is left floating.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS052 − APRIL 2004
320C40 (rev 7.0) known good die pad information
325
Pad Number One
Die Side Number 4
244
1
243
•
•
•
•
•
•
Die Side Number 1
Zero-Zero
(origin)
Die Designator
Die Side Number 3
•
•
•
•
•
•
81
163
82
Die Side Number 2
162
Figure 2. 320C40 Die Numbering Format
(See Table 1)
Table 1 provides a reference for the following:
D The C40 signal identities in relation to the pad numbers
D The C40 X, Y coordinates, where bond pad 82 serves as the origin (0,0)
In addition, the following notes are significant:
A.
X, Y coordinate data is in microns.
B.
The active silicon dimensions are 12 424.86 µm × 12 035.52 µm (489.16 mils × 473.83 mils).
C.
The die size is approximately 12 598.40 µm × 12 192.00 µm (496.00 mils × 480.00 mils).
D.
Bond pad dimensions are 108.00 µm × 108.00 µm (4.25 mils × 4.25 mils).
E.
Center of bond pad to edge of die min (without scribe) = 107.80 µm (4.24 mils).
F.
For R-Tab devices, gold bump dimensions are approximately 92 µm × 92 µm (3.62 mils × 3.62 mils).
G.
Coordinate origin is at (0,0) (center of bond pad 82).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
5
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm)
DIE SIDE #1
DIE/TAB BOND
PAD IDENTITY
1
D31
11368.44
126.00 (1, 2)
2
D30
11242.44
126.00 (2, 3)
3
D29
11116.44
126.00 (3, 4)
4
D28
10990.44
126.00 (4, 5)
5
D27
10864.44
126.00 (5, 6)
6
D26
10738.44
126.00 (6, 7)
7
GDDVDD
10612.44
126.00 (7, 8)
8
D25
10486.44
126.00 (8, 9)
9
D24
10360.44
126.00 (9, 10)
10
D23
10234.44
126.00 (10, 11)
11
D22
10108.44
126.00 (11, 12)
12
D21
9982.44
126.00 (12, 13)
13
D20
9856.44
126.00 (13, 14)
14
D19
9730.44
126.00 (14, 15)
15
D18
9604.44
126.00 (15, 16)
16
D17
9478.44
126.00 (16, 17)
17
D16
9352.44
126.00 (17, 18)
18
9226.44
126.00 (18, 19)
19
CVSS
IVSS
9100.44
126.00 (19, 20)
20
GDDVDD
8974.44
126.00 (20, 21)
21
DVSS
8848.44
126.00 (21, 22)
22
D15
8722.44
126.00 (22, 23)
23
D14
8596.44
126.00 (23, 24)
24
D13
8470.44
126.00 (24, 25)
25
D12
8344.44
126.00 (25, 26)
26
D11
8218.44
126.00 (26, 27)
27
D10
8092.44
126.00 (27, 28)
28
D9
7966.44
126.00 (28, 29)
29
D8
7840.44
126.00 (29, 30)
30
D7
7714.44
126.00 (30, 31)
31
D6
7588.44
126.00 (31, 32)
32
D5
7462.44
126.00 (32, 33)
33
GDDVDD
7336.44
126.00 (33, 34)
34
D4
7210.44
126.00 (34, 35)
35
D3
7084.44
126.00 (35, 36)
36
D2
6958.44
126.00 (36, 37)
37
D1
6832.44
126.00 (37, 38)
38
D0
6706.44
156.42 (38, 39)
39
CE1
6550.02
172.80 (39, 40)
40
RDY1
6377.22
152.10 (40, 41)
41
DVSS
CVSS
6225.12
126.00 (41, 42)
6099.12
126.00 (42, 43)
42
6
X-COORDINATE OF DIE
BOND PAD
− 429.48
POST OFFICE BOX 1443
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
• HOUSTON, TEXAS 77251−1443
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #1 (CONTINUED)
X-COORDINATE OF DIE
BOND PAD
DIE/TAB BOND
PAD IDENTITY
43
LOCK
5973.12
126.00 (43, 44)
44
VDDL
VSSL
5847.12
126.00 (44, 45)
45
5721.12
156.42 (45, 46)
46
CE0
5564.70
172.80 (46, 47)
47
RDY0
5391.90
172.80 (47, 48)
48
DE
5219.10
172.80 (48, 49)
49
TCK
5046.30
152.10 (49, 50)
50
TDO
4894.20
156.42 (50, 51)
51
TDI
4737.78
172.80 (51, 52)
52
TMS
4564.98
172.80 (52, 53)
53
TRST
4392.18
151.10 (53, 54)
54
EMU0
4240.08
126.00 (54, 55)
55
EMU1
4114.08
126.00 (55, 56)
56
3988.08
126.00 (56, 57)
57
DVSS
DVDD
3962.08
126.00 (57, 58)
58
PAGE1
3736.08
126.00 (58, 59)
59
R / W1
3610.08
126.00 (59, 60)
60
STRB1
3484.08
126.00 (60, 61)
61
STAT0
3358.08
126.00 (61, 62)
62
STAT1
3232.08
126.00 (62, 63)
63
3106.08
126.00 (63, 64)
64
IVSS
STAT2
2980.08
126.00 (64, 65)
65
STAT3
2854.08
127.44 (65, 66)
66
PAGE0
2726.64
126.00 (66, 67)
67
R / W0
2600.64
126.00 (67, 68)
68
STRB0
2474.64
156.42 (68, 69)
69
AE
2318.22
174.24 (69, 70)
70
RESETLOC 1
2143.98
152.10 (70, 71)
71
1991.88
156.42 (71, 72)
72
DVDD
RESETLOC 0
1835.46
172.80 (72, 73)
73
RESET
1662.66
172.80 (73, 74)
74
CRDY5
1510.56
126.00 (74, 75)
75
CSTRB5
1384.56
126.00 (75, 76)
76
CACK5
1258.56
126.00 (76, 77)
77
CREQ5
1132.56
126.00 (77, 78)
78
CRDY4
1006.56
126.00 (78, 79)
79
CSTRB4
880.56
126.00 (79, 80)
80
CACK4
754.56
126.00 (80, 81)
81
CREQ4
628.56
− 429.48
POST OFFICE BOX 1443
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
• HOUSTON, TEXAS 77251−1443
7
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #2
DIE/TAB BOND
PAD IDENTITY
X-COORDINATE OF DIE
BOND PAD
82
CVSS
DVSS
0.00
1062.00 (82, 83)
1062.00
126.00 (83, 84)
83
84
1188.00
126.00 (84, 85)
85
DVDD
C5D7
1314.00
126.00 (85, 86)
86
C5D6
1440.00
126.00 (86, 87)
87
C5D5
1566.00
126.00 (87, 88)
88
C5D4
1692.00
126.00 (88, 89)
89
C5D3
1818.00
126.00 (89, 90)
90
C5D2
1944.00
126.00 (90, 91)
91
C5D1
2070.00
126.00 (91, 92)
92
C5D0
2196.00
126.00 (92, 93)
93
2322.00
126.00 (93, 94)
94
DVDD
C4D7
2448.00
126.00 (94, 95)
95
C4D6
2574.00
126.00 (95, 96)
96
C4D5
2700.00
126.00 (96, 97)
97
C4D4
2813.40
126.00 (97, 98)
98
C4D3
2952.00
126.00 (98, 99)
99
C4D2
3078.00
126.00 (99, 100)
100
C4D1
3204.00
126.00 (100, 101)
101
C4D0
3330.00
126.00 (101, 102)
102
CVSS
DVSS
3456.00
3708.00
126.00 (104, 105)
105
DVDD
C3D7
3834.00
126.00 (105, 106)
106
C3D6
3960.00
126.00 (106, 107)
107
C3D5
4086.00
126.00 (107, 108)
108
C3D4
4212.00
126.00 (108, 109)
109
C3D3
4338.00
126.00 (109, 110)
110
C3D2
4464.00
126.00 (110, 111)
103
104
8
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
3582.00
0.00
126.00 (102, 103)
126.00 (103, 104)
111
C3D1
4590.00
126.00 (111, 112)
112
C3D0
4716.00
126.00 (112, 113)
113
4842.00
126.00 (113, 114)
114
DVDD
IVSS
4968.00
126.00 (114, 115)
115
C2D7
5094.00
126.00 (115, 116)
116
C2D6
5220.00
126.00 (116, 117)
117
C2D5
5346.00
126.00 (117, 118)
118
C2D4
5472.00
126.00 (118, 119)
119
C2D3
5598.00
126.00 (119, 120)
120
C2D2
5724.00
126.00 (120, 121)
121
C2D1
5850.00
126.00 (121, 122)
122
C2D0
5976.00
126.00 (122, 123)
123
CVSS
6102.00
126.00 (123, 124)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #2 (CONTINUED)
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
DIE/TAB BOND
PAD IDENTITY
X-COORDINATE OF DIE
BOND PAD
124
6228.00
126.00 (124, 125)
125
DVSS
DVDD
6354.00
126.00 (125, 126)
126
CRDY3
6480.00
126.00 (126, 127)
127
CSTRB3
6606.00
126.00 (127, 128)
128
CACK3
6732.00
126.00 (128, 129)
129
CREQ3
6858.00
126.00 (129, 130)
130
6984.00
126.00 (130, 131)
131
VDDL
VSSL
7110.00
126.00 (131, 132)
132
CRDY2
7236.00
126.00 (132, 133)
133
CSTRB2
7362.00
126.00 (133, 134)
134
CACK2
7488.00
126.00 (134, 135)
135
CREQ2
7614.00
126.00 (135, 136)
136
DVDD
CRDY1
7740.00
126.00 (136, 137)
137
7866.00
126.00 (137, 138)
138
CSTRB1
7992.00
126.00 (138, 139)
139
CACK1
8118.00
126.00 (139, 140)
140
CREQ1
8244.00
126.00 (140, 141)
141
CRDY0
8370.00
126.00 (141, 142)
142
CSTRB0
8496.00
143
CACK0
8622.00
144
CREQ0
8748.00
126.00 (144, 145)
145
CVSS
DVSS
8874.00
126.00 (145, 146)
9000.00
126.00 (146, 147)
9126.00
126.00 (147, 148)
9252.00
126.00 (148, 149)
149
IVSS
DVDD
C1D7
9378.00
126.00 (149, 150)
150
C1D6
9504.00
126.00 (150, 151)
151
C1D5
9630.00
126.00 (151, 152)
152
C1D4
9756.00
126.00 (152, 153)
153
C1D3
9882.00
126.00 (153, 154)
154
C1D2
10008.00
126.00 (154, 155)
155
C1D1
10134.00
126.00 (155, 156)
156
C1D0
10260.00
126.00 (156, 157)
157
10386.00
126.00 (157, 158)
158
DVDD
C0D7
10512.00
126.00 (158, 159)
159
C0D6
10638.00
126.00 (159, 160)
160
C0D5
10764.00
126.00 (160, 161)
161
C0D4
10890.00
126.00 (161, 162)
162
C0D3
11016.00
146
147
148
POST OFFICE BOX 1443
126.00 (142, 143)
0.00
• HOUSTON, TEXAS 77251−1443
126.00 (143, 144)
9
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #3
C40 DIE BOND
PAD LOCATIONS
DIE/TAB BOND
PAD IDENTITY
163
C0D2
164
165
166
10
X-COORDINATE OF DIE
BOND PAD
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
810.00
126.00 (163, 164)
C0D1
936.00
126.00 (164, 165)
C0D0
1062.00
126.00 (165, 166)
1188.00
126.00 (166, 167)
167
CVSS
DVDD
1314.00
156.42 (167, 168)
168
ROMEN
1470.42
152.46 (168, 169)
169
IIOF0
1622.88
126.00 (169, 170)
170
DVSS
IIOF1
1748.88
126.00 (170, 171)
171
1874.88
126.00 (171, 172)
172
IIOF2
2000.88
126.00 (172, 173)
173
IIOF3
2126.88
156.42 (173, 174)
174
NMI
2283.30
152.10 (174, 175)
175
LSTRB0
2435.40
126.00 (175, 176)
176
LR / W0
2561.40
126.00 (176, 177)
177
LPAGE0
2687.40
156.42 (177, 178)
178
LRDY0
2843.82
172.80 (178, 179)
179
LCE0
3016.62
152.10 (179, 180)
180
LSTRB1
3168.72
126.00 (180, 181)
181
LR / W1
3294.72
126.00 (181, 182)
182
3420.72
126.00 (182, 183)
183
DVDD
CVSS
3546.72
126.00 (183, 184)
184
LPAGE1
3672.72
156.42 (184, 185)
185
LRDY1
3829.14
172.80 (185, 186)
186
LCE1
4001.94
172.80 (186, 187)
187
LDE
4174.74
152.10 (187, 188)
188
TCLK0
4326.84
126.00 (188, 189)
189
TCLK1
4452.84
126.00 (189, 190)
190
H3
4578.84
126.00 (190, 191)
191
H1
4704.84
156.42 (191, 192)
192
LAE
4861.26
152.10 (192, 193)
193
5013.36
126.00 (193, 194)
194
IVSS
LLOCK
5139.36
126.00 (194, 195)
195
LSTAT0
5265.36
126.00 (195, 196)
196
LSTAT1
5391.36
126.00 (196, 197)
197
LSTAT2
5517.36
126.00 (197, 198)
198
LSTAT3
5643.36
127.44 (198, 199)
199
IACK
5770.80
126.00 (199, 200)
200
VDDL
VSSL
5896.80
126.00 (200, 201)
201
6022.80
131.94 (201, 202)
202
X1
6154.74
171.58 (202, 203)
203
X2 / CLKIN
6326.28
168.12 (203, 204)
204
CVSS
6494.40
126.00 (204, 205)
11779.74
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #3 (CONTINUED)
DIE/TAB BOND
PAD IDENTITY
205
6620.40
126.00 (205, 206)
206
DVDD
DVSS
6746.40
127.44 (206, 207)
207
LA30
6873.84
126.00 (207, 208)
208
LA29
6999.84
126.00 (208, 209)
209
LA28
7125.84
126.00 (209, 210)
210
LA27
7251.84
126.00 (210, 211)
211
7377.84
126.00 (211, 212)
212
LADVDD
LA26
7503.84
126.00 (212, 213)
213
LA25
7629.84
126.00 (213, 214)
214
LA24
7755.84
126.00 (214, 215)
215
LA23
7881.84
126.00 (215, 216)
216
LA22
8007.84
126.00 (216, 217)
217
LA21
8133.84
126.00 (217, 218)
218
LA20
8259.84
126.00 (218, 219)
219
LA19
8385.84
126.00 (219, 220)
220
LA18
8511.84
126.00 (220, 221)
221
LA17
8637.84
126.00 (221, 222)
222
LA16
8763.84
126.00 (222, 223)
223
LADVDD
CVSS
8889.84
126.00 (223, 224)
9015.84
126.00 (224, 225)
9141.84
126.00 (225, 226)
226
DVSS
LA15
9267.84
126.00 (226, 227)
227
LA14
9393.84
126.00 (227, 228)
228
LA13
9519.84
126.00 (228, 229)
229
LA12
9645.84
126.00 (229, 230)
230
LA11
9771.84
126.00 (230, 231)
231
LA10
9897.84
126.00 (231, 232)
232
LA9
10023.84
126.00 (232, 233)
233
LA8
10149.84
126.00 (233, 234)
234
LA7
10275.84
126.00 (234, 235)
235
LA6
10401.84
126.00 (235, 236)
236
LA5
10527.84
126.00 (236, 237)
237
LA4
10653.84
126.00 (237, 238)
238
10779.84
126.00 (238, 239)
239
LADVDD
LA3
10905.84
126.00 (239, 240)
240
LA2
11031.84
126.00 (240, 241)
241
LA1
11157.84
126.00 (241, 242)
242
LA0
11283.84
205.92 (242, 243)
243
DVSS
11489.76
224
225
X-COORDINATE OF DIE
BOND PAD
11779.74
POST OFFICE BOX 1443
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
• HOUSTON, TEXAS 77251−1443
11
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #4
DIE/TAB BOND
PAD IDENTITY
X-COORDINATE OF DIE
BOND PAD
244
10953.72
126.00 (244, 245)
245
CVSS
LD31
10827.72
126.00 (245, 246)
246
LD30
10701.72
126.00 (246, 247)
247
LD29
10575.72
126.00 (247, 248)
248
LD28
10449.72
126.00 (248, 249)
249
10323.72
126.00 (249, 250)
250
LDDVDD
LD27
10197.72
126.00 (250, 251)
251
LD26
10071.72
126.00 (251, 252)
252
LD25
9945.72
126.00 (252, 253)
253
LD24
9819.72
126.00 (253, 254)
254
LD23
9693.72
126.00 (254, 255)
255
LD22
9567.72
126.00 (255, 256)
256
LD21
9441.72
126.00 (256, 257)
257
LD20
9315.72
126.00 (257, 258)
258
LD19
9189.72
126.00 (258, 259)
259
LD18
9063.72
126.00 (259, 260)
260
LD17
8937.72
126.00 (260, 261)
261
LDDVDD
CVSS
8811.72
126.00 (261, 262)
262
8685.72
126.00 (262, 263)
DVSS
IVSS
8559.72
126.00 (263, 264)
265
LD16
8307.72
266
LD15
8181.72
126.00 (266, 267)
267
LD14
8055.72
126.00 (267, 268)
268
LD13
7929.72
126.00 (268, 269)
269
LD12
7803.72
126.00 (269, 270)
270
LD11
7677.72
126.00 (270, 271)
271
LD10
7551.72
126.00 (271, 272)
272
LD9
7425.72
126.00 (272, 273)
273
LD8
7299.72
126.00 (273, 274)
274
LD7
7173.72
126.00 (274, 275)
275
LD6
7047.72
126.00 (275, 276)
276
LD5
6921.72
126.00 (276, 277)
277
6795.72
126.00 (277, 278)
278
LDDVDD
LD4
6669.72
126.00 (278, 279)
279
LD3
6543.72
126.00 (279, 280)
280
LD2
6417.72
126.00 (280, 281)
281
LD1
6291.72
126.00 (281, 282)
282
LD0
6165.72
127.62 (282, 283)
283
6038.10
126.00 (283, 284)
284
VDDL
VSSL
5912.10
126.00 (284, 285)
285
CVSS
5786.10
126.00 (285, 286)
263
264
12
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
8433.72
POST OFFICE BOX 1443
126.00 (264, 265)
11819.88
• HOUSTON, TEXAS 77251−1443
126.00 (265, 266)
SGUS052 − APRIL 2004
Table 1. 320C40 Die Pad / TAB Lead Information : Rev. 7.0 (0,72 µm) (Continued)
DIE SIDE #4 (CONTINUED)
DIE/TAB BOND
PAD IDENTITY
X-COORDINATE OF DIE
BOND PAD
286
5660.10
126.00 (286, 287)
287
DVSS
A30
5534.10
126.00 (287, 288)
288
A29
5408.10
126.00 (288, 289)
289
A28
5282.10
126.00 (289, 290)
290
GADVDD
5156.10
126.00 (290, 291)
291
A27
5030.10
126.00 (291, 292)
292
A26
4904.10
126.00 (292, 293)
293
A25
4778.10
126.00 (293, 294)
294
A24
4652.10
126.00 (294, 295)
295
A23
4526.10
126.00 (295, 296)
296
A22
4400.10
126.00 (296, 297)
297
A21
4274.10
126.00 (297, 298)
298
A20
4148.10
126.00 (298, 299)
299
A19
4022.10
126.00 (299, 300)
300
A18
3896.10
126.00 (300, 301)
301
A17
3770.10
126.00 (301, 302)
302
GADVDD
3644.10
126.00 (302, 303)
303
3518.10
126.00 (303, 304)
304
CVSS
DVSS
3392.10
126.00 (304, 305)
305
A16
3266.10
306
A15
3140.10
307
A14
3014.10
126.00 (307, 308)
308
A13
2888.10
126.00 (308, 309)
309
A12
2762.10
126.00 (309, 310)
310
A11
2636.10
126.00 (310, 311)
311
A10
2510.10
126.00 (311, 312)
312
A9
2384.10
126.00 (312, 313)
313
A8
2258.10
126.00 (313, 314)
314
A7
2132.10
126.00 (314, 315)
315
A6
2006.10
126.00 (315, 316)
316
A5
1880.10
126.00 (316, 317)
317
A4
1754.10
126.00 (317, 318)
318
GADVDD
1628.10
126.00 (318, 319)
319
A3
1502.10
126.00 (319, 320)
320
A2
1376.10
126.00 (320, 321)
321
A1
1250.10
126.00 (321, 322)
322
A0
1124.10
126.00 (322, 323)
323
CVSS
DVSS
998.10
558.00 (323, 324)
324
440.10
630.00 (324, 325)
325
SUBS
− 189.90
POST OFFICE BOX 1443
Y-COORDINATE OF DIE
BOND PAD
PITCH OF LEAD
(#, #) REFERENCES WHICH DIE
BOND PADS
C40 DIE BOND
PAD LOCATIONS
126.00 (305, 306)
11819.88
• HOUSTON, TEXAS 77251−1443
126.00 (306, 307)
13
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated