FTR-K1 SERIES POWER RELAY 1 POLE - 16A / Inrush 120A relay FTR-K1-KS Series n FEATURES 1 pole 16A, 1 form A or 1 form C l Peak inrush current 120A / TV-8 l Coil sensitive 400mW l High insulation in small package (between coil and contacts - Insulation distance: 10mm min. - Dielectric strength: 5,000VAC - Surge strength: 10,000V l UL1446 Class F coil insulation system l Cadmium-free contacts for eco-program l RoHS compliant Please see page 5 for more information l n PARTNUMBER INFORMATION [Example] FTR-K1 C K 005 (a) (b) (c) (d) T - KS (e) (f ) (a) Relay type FTR-K1: FTR-K1 Series (b) Contact configuration A C : 1 form A : 1 form C (c) Coil type K : Standard (400mW) (d)����� Coil rated ������ voltage� �������� ���� 005:�� ��������� 5.....48 ��� VDC Coil rating table at page 3 (e) Contact material / TV type T: AgSnO2 / TV-rating (f) ������� Inrush ����� type� ��� KS:�� ������� Inrush ��������� 120A type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK005T-KS Actual marking: K1CK005T-KS FTR-K1-KS FTR-K1SERIES SERIES n SPECIFICATION Item Contact Data Life FTR-K1CK ( ) T-KS FTR-K1AK ( )T-KS Configuration 1 form C 1 form A Material AgSnO2 Resistance (initial) ≤ 100mOhm at 1A, 6VDC Contact rating 16A, 250VAC Max. carrying current 20A Max. switching voltage 440VAC Max. switching power 4,000VA Min. switching load * 100 mA, 5VDC Max. inrush current 120A, 250VAC (N.O. contact) Mechanical 20 x 106 operations minimum Electrical 120A, 250VAC Resistive load 30 x 103 operations min. 100 x 103 operations min. Lamp load (TV-8) 25 x 103 operations min. (N.O. contact) 25 x 103 operations min. Coil Data Operating temperature range -40 °C to +85 °C (no frost) Timing Data Operate (at nominal voltage) ≤ 15ms (no bounce included) Release (at nominal voltage) ≤ 5ms (no diode, no bounce included) Resistance (initial) ≥ 1,000MOhm at 500VDC Insulation Dielectric strength Surge strength Other Vibration resistance Shock Weight Open contacts 1,000VAC, 1min. Contacts to coil 5,000VAC, 1min. Coil to contacts 10,000V / 1.2 x 50µs standard wave Misoperation ≥1µs 10 to 55Hz double amplitude 0.7mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation ≥1µs Min. 100m/s2 (11±1ms) Endurance Min. 1,000m/s2 (6±1ms) Approximately 13g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. FTR-K1SERIES SERIES FTR-K1-KS n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 005 5 62 3.5 0.5 006 6 90 4.2 0.6 009 9 202 6.3 0.9 012 12 360 8.4 1.2 018 18 810 12.6 1.8 022 22 1,210 15.4 2.2 024 24 1,440 16.8 2.4 028 28 1,960 19.6 2.8 048 48 5,360 33.6 4.8 Rated Power (mW) 400 430 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) CSA C22.2 No. 14 VDE 0435, 0631, 0700, 0860 16A, 277VAC resistive TV-8, 120VAC (NO) 16A, 250VAC, cosØ=1, T85 8/120A, 250VAC, T85 (NO) FTR-K1SERIES SERIES FTR-K1-KS n DIMENSIONS l Dimensions l PC board mounting hole layout l Schematics (BOTTOM VIEW) Unit: mm Note: In case of 1 form A, terminals marked are omitted. FTR-K1 SERIES SERIES FTR-K1-KS RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: maximum 120˚C Soldering: dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. FTR-K1SERIES SERIES FTR-K1-KS Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. November 6, 2009