FTR-K1 SERIES POWER RELAY 1 POLE - 20A Heavy Load FTR-K3 Series n FEATURES SPST 20A and #250 tab terminal type is also available Low coil power (780mW) l Type of service: continuous duty l Cadmium free contacts l SAFETY STANDARDS UL, CSA, VDE,CQC approved l RoHS compliant Please see page 6 for more information l l n PARTNUMBER INFORMATION FTR-K3 J [Example] (a) (b) (a) Relay type (b) Contact configuration (c) Coil type B (c) 012 (d) W - HC (e) (f ) FTR-K3 : FTR-K3-Series A J : 1 form A (SPST-NO) (PCB terminal) : 1 form A (SPST-NO) (Tab terminal) B : Standard type (780mW) (d) Coil rated voltage 012 : 5.....48 VDC Coil rating table at page 3 (e) W : Silver alloy Nil LS HC : Standard type (20A) : High isolation type (20A) : High current type (25A) Contact material (f) Option Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K3AB012W Actual marking: K3AB012W 1 FTR-K1 SERIES FTR-K3 SERIES n SPECIFICATION Item Contact Data Life FTR-K3 Configuration 1 form A Construction Single Material Silver alloy Resistance (initial) Max. 100mΩ at 1A, 6VDC Contact rating (resistive) 20A, 250VAC Max. carrying current 25A Max. switching current *¹ 25A Max. switching voltage 250VAC Max. switching power 6,250VA Min. switching load *² 100 mA, 5VDC Mechanical Min. 2 x 106 operations Electrical Coil Data Timing Data Insulation 20A, 250VAC Resistive load Min. 100 x 103 operations Motor load Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 20A cosφ=0.9) Inverter load Min. 30 x 103 operations 100VAC, inrush 200A / cut off 20A Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 20A cosφ=0.9) Rated power (at 20 °C) 780 mW Operate power (at 20 °C) 380 mW Operating temperature range -40 °C to +60 °C (no frost) Operate (at nominal voltage) Max. 20ms (without bounce) Release (at nominal voltage) Max. 10ms (no diode, without bounce) Resistance Min. 1,000MΩ at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 5,000VAC (50/60Hz) 1min Coil to contacts 8,500V / 1.2 x 50µs standard wave Clearance/creepage distance Other FTR-K3-LS Vibration resistance Shock 6.4mm / 9.5mm 8.0mm / 9.5mm Misoperation 10 to 55Hz double amplitude 1.5 mm Endurance 10 to 55Hz double amplitude 1.5 mm Misoperation Min. 200m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Weight Approximately 25 g Sealing Flux proof, RTII FTR-K3-HC 25A, 250VAC Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 25A cosφ=0.9) 6.4mm / 9.5mm * 1 Need to consider the heat from PCB when max. current is more than 10A * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-K3 SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * 005 5 32 3.5 0.5 006 6 46 4.2 0.6 009 9 105 6.3 0.9 012 12 185 8.4 1.2 018 18 415 12.6 1.8 024 24 740 16.8 2.4 048 48 2,955 33.6 4.8 Rated Power (mW) 780 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating FTR-K3 UL UL508 No. E63614 CSA C22.2 No. 14 No. LR40304 FTR-K3-LS FTR-K3-HC 20A, 277VAC (resistive at 60 °C) 1hp, 125VAC (at 60 °C) 2hp, 277VAC (100,000 ops. at 60 °C) 25A, 277VAC (resistive at 60 °C) 1hp, 125VAC (at 60 °C) 2hp, 277VAC (100,000 ops. at 60 °C) 20A, 277VAC (resistive) 1hp, 125VAC 2hp, 277VAC (100,000 ops.) 25A, 277VAC (resistive) 1hp, 125VAC 2hp, 277VAC (100,000 ops.) - VDE IEC61810-1 20A, 250VAC (cos φ=1) 60 °C 25A, 250VAC (cos φ=1) 60 °C CQC GB15092-1 GB8898 GB/T21711.1 No. 04001009179 20A, 250VAC 25A, 250VAC EN61058-1 20A, 250VAC, 40T60/ 20 (13.33) A 250VAC, 40T60 20/200A 100VAC, 40T60 SEMKO EN61095 TUV EN61810-1 IEC61810-1 - - - 20A, 250VAC (cos φ=1) 60 °C - - 3 FTR-K1 SERIES FTR-K3 SERIES n CHARACTERISTIC DATA 4 FTR-K1 SERIES FTR-K3 SERIES FTR-K3-HC type n Electrical life tests (resistive load) DIMENSIONS FTR-K3 AB type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) l Schematics l PC board mounting hole layout (BOTTOM VIEW) FTR-K3 JB type l Dimensions 5 FTR-K1 SERIES FTR-K3 SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to through hole mounted electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1 SERIES FTR-K3 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 13, 2011 7