FTR-K1 SERIES POWER RELAY 1 POLE - 32A, 1.5mm contact gap latching relay FTR-K3L-PV Series n FEATURES 1 pole, 32A 1 form A contact l Wide contact gap: 1.5mm Surge strength (B/T open contacts) 2.5kV Compliant with European photovoltaic standard (VDE0126) l High insulation in small package (between coil and contacts) - Dielectric strength: AC 4,000V - Surge strength: 6,000V l Low coil power consumption: 1,200mW l Plastic materials: Flammability; UL94 V-0 l Cadmium-free contacts l RoHS compliant. Please see page 5 for more information l l n PARTNUMBER INFORMATION [Example] FTR-K3L A (a) (b) B 012 (c) (d) W - PV (e) (f ) (a) Relay type FTR-K3L: FTR-K3L-Series (b) (c) Contact configuration A : 1 form A / PCB type Coil type B : Standard sensitive (1,200mW) (d) Coil rated voltage 012 : 5.....24 VDC Coil rating table at page 3 (e) Contact material W : Silver alloy (f) Version PV : High current (32A) / contact gap 1.5mm E.g.: Ordering code: FTR-K3LAB012W-PV Actual marking: K3LAB012W-PV 1 FTR-K1 SERIES FTR-K3L-PV SERIES n SPECIFICATION Item Contact Data Life FTR-K3L-PV Configuration 1 form A Material Silver alloy Resistance (initial) Max. 100 mΩ at 6VDC, 1A Contact rating (resistive) 32A, 250VAC Max. carrying current 32A Max. switching voltage 250VAC Max. switching power 8,000VA Max. switching current 32A Min. switching load * 100mA, 5VDC (reference value) Mechanical Min. 1 x 106 operations Electrical Coil Data Timing Data Insulation 32A / 250VAC, min. 30 x 103 operations Inductive 32A, 250VAC (cosφ 0.8), 30 x 103 operations Inductive (overload) 48A, 250VAC (cosφ 0.8), 50 operations Rated power (at 20 °C) 1,200mW Operating temperature range -40 °C to +85 °C Set (at nominal voltage) Max. 20ms (without bounce) Reset (at nominal voltage) Max. 20ms (without bounce) Coil excitation time (at nominal voltage) Min. 30ms, max. 1000ms Contact gap Min. 1.5mm Resistance Min. 1,000MΩ at 500VDC Dielectric strength Surge strength Other Resistive Open contacts 2,500VAC (50/60Hz) 1min Contacts to coil 4,000VAC (50/60Hz) 1min Contacts to coil 6,000V / 1.2 x 50µs standard wave Clearance Min. 6.0mm Creepage Min. 8.0mm Vibration resistance Shock Weight Misoperation 10 to 55Hz double amplitude 1.5mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation Min. 200m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Approximately 25g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-K3L-PV SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Set Voltage (VDC) * Must Reset Voltage (VDC) * Max. Set/Reset Voltage (VDC) 005 5 P 21 +4.0 - 9.0 S 21 - +4.0 P 30 +5.4 - S 30 - +5.4 P 120 +9.6 - S 120 - +9.6 P 480 +19.2 - S 480 - +19.2 006 012 024 6 12 24 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n Rated Power (mW) 10.8 1,200 21.6 43.2 P: Set coil S: Reset coil SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) CSA 22.2 No.14 (by cULus) VDE IEC61810-1 32A, 277VAC (General use at 60 °C) 32A, 250VAC (cosφ = 0.8) at +85 °C 3 FTR-K1 SERIES FTR-K3L-PV SERIES n CHARACTERISTIC DATA The graphs are based on measurement data and are typical values. n Electrical life tests (resistive load) DIMENSIONS l Dimensions l Schematics P: Set coil S: Reset coil Contacts drawn in reset condition. To operate (set), apply (+) to pin 5 and (-) to pin 2. To release (reset), apply (+) to pin 5 and (-) to pin 1. l PC board mounting hole layout (BOTTOM VIEW) 4 FTR-K1 SERIES FTR-K3L-PV SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 5 FTR-K1 SERIES FTR-K3L-PV SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. August 11, 2011 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fujitsu: FTR-K3LAB012W-PV FTR-K3LAB024W-PV