HOLTEK HT48R52A_10

HT48R52A
I/O Type 8-Bit OTP MCU with 16´16 High Current LED Driver
Technical Document
· Tools Information
· FAQs
· Application Note
-
HA0002E
HA0007E
HA0011E
HA0019E
HA0020E
Reading Larger than Usual MCU Tables
Using the MCU Look Up Table Instructions
HT48 & HT46 Keyboard Scan Program
Using the Watchdog Timer in the HT48 MCU Series
Using the Timer/Event Counter in the HT48 MCU Series
Features
· Operating voltage:
· External RC and 32768Hz crystal oscillator
fSYS=32768Hz: 2.2V~5.5V
fSYS=4MHz: 2.2V~5.5V
fSYS=8MHz: 3.3V~5.5V
· Dual clock system offers three operating modes
- Normal mode: Both RC and 32768Hz clock active
- Slow mode: 32768Hz clock only
- Idle mode: Periodical wake-up by watchdog timer
· 2k´14 program memory ROM
· 88´8 data memory RAM
overflow
· HALT function and wake-up feature reduce power
· 8 bidirectional I/O lines
consumption
· Max. 16´16 LED driver output
· 14-bit table read instructions
· 8 LED shared I/O lines
· 63 powerful instructions
· 24 LED shared output
· One instruction cycle: 4 system clock periods
· One external interrupt input
· All instructions in 1 or 2 instruction cycles
· One internal interrupt
· Bit manipulation instructions
· 8 bit programmable timer/event counter
· Up to 0.5ms instruction cycle with 8MHz system clock
· 4-level subroutine nesting
· 44/52-pin QFP and 44-pin LQFP packages
· Watchdog Timer (WDT)
· Low voltage reset (LVR)
General Description
This device is an 8-bit high performance, RISC architecture microcontroller specifically designed for multiple
I/O control product applications. The advantages of low
power consumption, I/O flexibility, timer functions, oscillator options, HALT and wake-up functions, watchdog
Rev. 1.60
timer, as well as low cost, enhance the versatility of
these devices to suit a wide range of application possibilities such as industrial control, consumer products,
subsystem controllers, etc.
1
April 28, 2010
HT48R52A
Block Diagram
In te rru p t
C ir c u it
S ta c k
IN T C
S ta c k P o in te r
P ro g ra m
C o u n te r
W D T
C o u n te r
T M R
A d d re s s D e c o d e r
P ro g ra m
T M R C
L o o k u p T a b le
P o in te r
M e m o ry
U
X
M
U
X
fS Y S /4
R T C O S C
W D T O S C
fS Y S /4
P B 4 ~ P B 7
P B 3 /T M R
P B 0 ~ P B 2
P B
S h ifte r
In s tr u c tio n
D e c o d e r
M e m o ry
P o in te r
P A C
M U X
T im in g
G e n e ra to r
P C
M e m o ry
W D T
O s c illa to r
R T C
O s c illa to r
O S C 3
O S C 4
S , V
B , V
, V
S S
P O R T C
P O R T D
P E
P A 0 ~ P A 7
P C 0 ~ P C 7
P D 0 /IN T
P D
R e s e t &
L V R
R E
V D D
V S S
V
P O R T A
P A
A d d re s s D e c o d e r
P ro g ra m
Rev. 1.60
X
P r e s c a le r
P B C
A C C
M U X
A L U
O S C 1
U
M
L o o k u p T a b le
R e g is te r
In s tr u c tio n
R e g is te r
R C
O s c illa to r
M
P O R T E
P D 1 ~ P D 7
P E 0 ~ P E 7
D D
D D C
S S D
E
2
April 28, 2010
HT48R52A
Pin Assignment
O
O
O
T
S C 3
S C 4
V D D
E S T
S C 1
R E S
P A 0
P A 1
P A 2
P A 3
P A 4
P A 5
P A 6
O
O
O
T
S C 3
S C 4
V D D
E S T
S C 1
R E S
P A 0
P A 1
P A 2
P A 3
P A 4
P A 5
P A 6
P A 7
P E 0
P E 1
P E 2
V S S E
P E 3
P E 4
P E 5
P E 6
4 4 4 3 4 2 4 1 4 0 3 9 3 8 3 7 3 6 3 5 3 4
1
3 3
2
3 2
3
3 1
4
3 0
5
H T 4 8 R 5 2 A
4 4 Q F P -A /L Q F P -A
6
7
2 9
2 8
2 7
8
2 6
9
2 5
1 0
2 4
1 1
1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2
2 3
V S S
P B 7
P B 6
P B 5
P B 4
V D D B
V D D B
P B 3 /T M R
P B 2
P B 1
P B 0
P A 7
P E 0
P E 1
P E 2
V S S E
P E 3
P E 4
P E 5
P E 6
P E 7
P D 0 /IN T
P D 1
P D 2
5 2 5 1 5 0 4 9 4 8 4 7 4 6 4 5 4 4 4 3 4 2 4 1 4 0
1
3 9
3 8
2
3 7
3
3 6
4
5
3 5
6
H T 4 8 R 5 2 A
5 2 Q F P -A
7
8
9
1 0
1 1
1 2
1 3
P C 5
P C 4
V D D C
P C 3
P C 2
P C 1
P C 0
P D 7
P D 6
P D 5
V S S D
P D 4
P D 3
P C 7
P C 6
P C 5
P C 4
V D D C
P C 3
P C 2
P C 1
P C 0
V S S D
P D 0 /IN T
1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6
3 4
3 3
3 2
3 1
3 0
2 9
2 8
2 7
V S S
P B 7
P B 6
P B 5
P B 4
V D D B
V D D B
P B 3 /T M R
P B 2
P B 1
P B 0
P C 7
P C 6
Pin Description
Pin Name
I/O
Options
Description
Bidirectional 8-bit input/output port. Software instructions determine if the pin
is a CMOS output or Schmitt trigger input. A pull-high resistor can be connected via configuration option. Each pin can be setup to be a wake-up input
via configuration options.
PA0~PA7
I/O
Pull-high
Wake-up
PB0~PB2,
PB3/TMR
PB4~PB7
I/O
¾
Bidirectional 8-bit input/output port.
The timer input is pin-shared with PB3.
PC0~PC7
O
¾
PC0~PC7 are PMOS output pins.
PD0/INT
I/O
¾
External interrupt input. Pin-shared with PD0 and activated on a high to low or
low to high transition. PD0 is NMOS type output pin.
PD1~PD7
O
¾
PD1~PD7 are NMOS output pins.
PE0~PE7
O
¾
PE0~PE7 are NMOS output pins.
RES
I
¾
Schmitt trigger reset input. Active low.
OSC1
I
¾
OSC1 is connected to a external resistor for the internal system clock.
OSC3
OSC4
I
O
¾
Real time clock oscillator. OSC3 and OSC4 are connected to a 32768Hz crystal oscillator for system clock timing purposes.
TEST
I
¾
TEST pin is internally pulled-high and can be left floating.
For test only.
VDD
¾
¾
Positive power supply
VDDB
¾
¾
PB port positive power supply
VDDC
¾
¾
PC port positive power supply
VSS
¾
¾
Negative Power supply, ground
VSSD,
VSSE
¾
¾
PD & PE port negative power supply, ground
Rev. 1.60
3
April 28, 2010
HT48R52A
Absolute Maximum Ratings
Supply Voltage ...........................VSS-0.3V to VSS+6.0V
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
Operating Temperature...........................-40°C to 85°C
IOL Total ..............................................................300mA
IOH Total............................................................-200mA
Total Power Dissipation .....................................500mW
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed
in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
D.C. Characteristics
Symbol
VDD
IDD1
Parameter
Operating Voltage
Ta=25°C
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
¾
fSYS=4MHz
2.2
¾
5.5
¾
fSYS=8MHz
3.3
¾
5.5
¾
fSYS=32768Hz
2.2
¾
5.5
¾
1.2
2
¾
2.5
5
¾
4
8
¾
20
40
¾
50
100
¾
3
5
¾
6
10
¾
1
2
¾
2
4
¾
2
4
¾
4
8
¾
¾
1
¾
¾
2
3V
Operating Current (RC OSC)
No load, fSYS=4MHz
5V
Unit
V
mA
IDD2
Operating Current (RC OSC)
5V
No load, fSYS=8MHz
Operating Current
(*RTC OSC Enabled,
RC OSC Disabled)
3V
IDD3
No load,
fSYS=32768Hz
Standby Current
(WDT OSC, *RTC OSC Enabled)
3V
Standby Current (WDT OSC Disabled,
*RTC OSC Enabled)
3V
Standby Current (WDT OSC Enabled,
RTC OSC Disabled)
3V
Standby Current
(WDT OSC, RTC OSC Disabled)
3V
Input Low Voltage for I/O Ports
¾
¾
0
¾
0.3VDD
V
Input High Voltage for I/O Ports
¾
¾
0.7VDD
¾
VDD
V
V
ISTB1
ISTB2
ISTB3
ISTB4
VIL1
VIH1
5V
5V
5V
5V
5V
No load,
system HALT
No load,
system HALT
No load,
system HALT
No load,
system HALT
mA
mA
mA
mA
mA
mA
Input Low Voltage (RES)
¾
¾
0
¾
0.4VDD
VIH2
Input High Voltage (RES)
¾
¾
0.9VDD
¾
VDD
V
VLVR
Low Voltage Reset
¾
3.3V option
2.7
3
3.3
V
IOL1
4
8
I/O Port Sink Current for PA
¾
10
20
¾
8
16
¾
20
40
¾
-2
-4
¾
-5
-10
¾
VIL2
3V
VOL=0.1VDD
5V
IOL2
3V
I/O Port Sink Current for PD, PE
VOL=0.1VDD
5V
IOH1
3V
I/O Port Source Current for PA
VOH=0.9VDD
5V
Rev. 1.60
4
mA
mA
mA
April 28, 2010
HT48R52A
Symbol
IOH2
Test Conditions
Parameter
VDD
3V
I/O Port Source Current for PB, PC
Conditions
VOH=0.9VDD
5V
RPH
3V
¾
Pull-high Resistance
5V
Min.
Typ.
Max.
-4
-8
¾
-10
-20
¾
20
60
100
10
30
50
Unit
mA
kW
Note: * RTC OSC in slow start oscillating
A.C. Characteristics
Symbol
fSYS
fTIMER
Parameter
System Clock (RC OSC)
Timer I/P Frequency
tWDTOSC Watchdog Oscillator Period
Ta=25°C
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
¾
2.2V~5.5V
400
¾
4000
¾
3.3V~5.5V
400
¾
8000
¾
2.2V~5.5V
0
¾
4000
¾
3.3V~5.5V
0
¾
8000
Unit
kHz
kHz
3V
¾
45
90
180
ms
5V
¾
32
65
130
ms
184
369
737
131
266
532
¾
125
¾
¾
125
¾
1
¾
¾
ms
¾
1024
¾
tSYS
3V
tFSP1
fSP Time-out Period Clock Source
from WDT
tFSP2
fSP Time-out Period Clock Source
from RTC Oscillator
5V
tRES
External Reset Low Pulse Width
¾
tSST
System Start-up Timer Period
¾
tLVR
Low Voltage Width to Reset
¾
¾
0.25
1
2
ms
tINT
Interrupt Pulse Width
¾
¾
1
¾
¾
ms
5V
3V
With prescaler (fS/4096)
With prescaler (fS/4096)
¾
Power-up or wake-up
from HALT
ms
ms
Note: tSYS=1/fSYS
Rev. 1.60
5
April 28, 2010
HT48R52A
Functional Description
Execution Flow
incremented by one. The program counter then points to
the memory word containing the next instruction code.
The system clock for the microcontroller is derived from
either an RC oscillator or a RTC oscillator. The system
clock is internally divided into four non-overlapping
clocks. One instruction cycle consists of four system
clock cycles.
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call or return
from subroutine, initial reset, internal interrupt, external
interrupt or return from interrupt, the PC manipulates the
program transfer by loading the address corresponding
to each instruction.
Instruction fetching and execution are pipelined in such
a way that a fetch takes an instruction cycle while decoding and execution takes the next instruction cycle.
However, the pipelining scheme causes each instruction to be effectively executed in a cycle. If an instruction
changes the program counter, two cycles are required to
complete the instruction.
The conditional skip is activated by instructions. Once
the condition is met, the next instruction, fetched during
the current instruction execution, is discarded and a
dummy cycle replaces it to get the proper instruction.
Otherwise proceed with the next instruction.
The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the
PCL performs a short jump. The destination will be
within 256 locations.
Program Counter - PC
The program counter (PC) controls the sequence in
which the instructions stored in the program ROM are
executed and its contents specify a full range of program memory.
When a control transfer takes place, an additional
dummy cycle is required.
After accessing a program memory word to fetch an instruction code, the contents of the program counter are
S y s te m
O S C 2 (R C
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
o n ly )
P C
P C
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Mode
Program Counter
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
External Interrupt
0
0
0
0
0
0
0
0
1
0
0
Timer/Event Counter Overflow
0
0
0
0
0
0
0
1
0
0
0
Skip
Program Counter+2
Loading PCL
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from Subroutine
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note: *10~*0: Program counter bits
S10~S0: Stack register bits
#10~#0: Instruction code bits
Rev. 1.60
@7~@0: PCL bits
6
April 28, 2010
HT48R52A
0 0 0 H
Program Memory - ROM
D e v ic e In itia liz a tio n P r o g r a m
0 0 4 H
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
2048´14 bits, addressed by the program counter and table pointer.
E x te r n a l In te r r u p t S u b r o u tin e
0 0 8 H
T im e r /E v e n t C o u n te r In te r r u p t S u b r o u tin e
P ro g ra m
M e m o ry
n 0 0 H
Certain locations in the program memory are reserved
for special usage:
L o o k - u p T a b le ( 2 5 6 w o r d s )
n F F H
· Location 000H
7 0 0 H
This area is reserved for program initialisation. After a
chip reset, the program always begins execution at location 000H.
L o o k - u p T a b le ( 2 5 6 w o r d s )
7 F F H
1 4 b its
N o te : n ra n g e s fro m
· Location 004H
This area is reserved for the external interrupt service
program. If the INT input pin is activated, the interrupt
is enabled and the stack is not full, the program begins
execution at location 004H.
instruction in the main routine and the ISR simultaneously should be avoided. However, if the table read
instruction has to be applied in both the main routine
and the ISR, the interrupt should be disabled prior to
using the table read instruction. It should not be enabled until the TBLH has been backed up. All table related instructions require two cycles to complete the
operation. These areas may function as normal program memory depending upon the requirements.
· Location 008H
This area is reserved for the timer/event counter interrupt service program. If a timer interrupt results from a
timer/event counter overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H .
· Table location
Stack Register - STACK
Any location in the program memory space can be
used as look-up tables. The instructions ²TABRDC
[m]² (the current page, one page=256 words) and
²TABRDL [m]² (the last page) transfer the contents of
the lower-order byte to the specified data memory,
and the higher-order byte to TBLH (08H). Only the
destination of the lower-order byte in the table is
well-defined, the other bits of the table word are transferred to the lower portion of the TBLH, and the remaining 2-bit words are read as ²0². The Table
Higher-order byte register (TBLH) is read only. The table pointer (TBLP) is a read/write register (07H),
which indicates the table location. Before accessing
the table, the location must be placed in the TBLP. The
TBLH is read only and cannot be restored. If the main
routine and the ISR (Interrupt Service Routine) both
employ the table read instruction, the contents of the
TBLH in the main routine are likely to be changed by
the table read instruction used in the ISR, therefore
errors may occur. In other words, using the table read
Instruction
0 to 7
Program Memory
This is a special part of the memory which is used to
save the contents of the program counter only. The
stack is organized into 4 levels and is neither part of the
data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the
stack pointer (SP) and is neither readable nor writeable.
At a subroutine call or interrupt acknowledge signal, the
contents of the program counter are pushed onto the
stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction, RET or RETI, the program counter is restored to its previous value from the
stack. After a chip reset, the stack pointer will point to
the top of the stack.
If the stack is full and a non-masked interrupt takes place,
the interrupt request flag will be recorded but the
acknowledge signal will be inhibited. When the stack
pointer is decremented, by RET or RET, the interrupt will
be serviced. This feature prevents stack overflow
allowing the programmer to use the structure more easily.
In a similar case, if the stack is full and a ²CALL² is
Table Location
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: *10~*0: Table location bits
P10~P8: Current program counter bits
@7~@0: Table pointer bits
Rev. 1.60
7
April 28, 2010
HT48R52A
0 0 H
subsequently executed, a stack overflow occurs and the
first entry will be lost. Only the most recent 4 return
addresses are stored.
Data Memory - RAM
In d ir e c t A d d r e s s in g R e g is te r 0
0 1 H
M P 0
0 2 H
In d ir e c t A d d r e s s in g R e g is te r 1
0 3 H
M P 1
0 4 H
0 5 H
The data memory has a capacity of 108´8 bits. The
data memory is divided into two functional groups,
namely, function registers and general purpose data
memory (88´8). Most are read/write, but some are
read only.
A C C
0 6 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
All of the data memory areas can handle arithmetic,
logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the
data memory can be set and reset by ²SET [m].i² and
²CLR [m].i². They are also indirectly accessible through
the memory pointer registers.
0 A H
S T A T U S
0 B H
IN T C
0 C H
0 D H
T M R
0 E H
T M R C
0 F H
1 0 H
1 1 H
Indirect Addressing Register
Location 00H and 02H are indirect addressing registers
that are not physically implemented. Any read/write operation of [00H] ([02H]) will access the data memory
pointed to by MP0 (MP1). Reading location 00H (02H)
itself indirectly will return the result ²00H². Writing indirectly results in no operation.
1 2 H
P A
1 3 H
P A C
1 4 H
P B
1 5 H
P B C
1 6 H
P C
S p e c ia l P u r p o s e
D a ta M e m o ry
1 7 H
1 8 H
P D
1 9 H
1 A H
The memory pointer registers, MP0 and MP1, are 7-bit
registers.
P E
1 B H
1 C H
1 D H
Accumulator
1 E H
The accumulator is closely related to ALU operations. It
is also mapped to location 05H of the data memory and
can carry out immediate data operations. The data
movement between two data memory locations must
pass through the accumulator.
1 F H
2 0 H
2 8 H
Arithmetic and logic unit - ALU
This circuit performs 8-bit arithmetic and logic operations. The ALU provides the following functions:
7 F H
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
G e n e ra l P u rp o s e
D a ta M e m o ry
(8 8 B y te s )
: U n u s e d
R e a d a s "0 0 "
RAM Mapping
· Logic operations (AND, OR, XOR, CPL)
register will not change the TO or PDF flag. In addition, operations related to the status register may
give different results from those intended. The TO
flag can be affected only by a system power-up, a
WDT time-out or executing the ²CLR WDT² or
²HALT² instruction. The PDF flag can be affected
only by executing the ²HALT² or ²CLR WDT² instruction or during a system power-up.
· Rotation (RL, RR, RLC, RRC)
· Increment and Decrement (INC, DEC)
· Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation
but also changes the status register.
Status Register - STATUS
This 8-bit register (0AH) contains the zero flag (Z), carry
flag (C), auxiliary carry flag (AC), overflow flag (OV),
power down flag (PDF), and watchdog time-out flag
(TO). It also records the status information and controls
the operation sequence.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
In addition, on entering the interrupt sequence or executing the subroutine call, the status register will not be
automatically pushed onto the stack. If the contents of
the status register are important and if the subroutine
can corrupt the status register, precautions must be
taken to save it properly.
With the exception of the TO and PDF flags, bits in
the status register can be altered by instructions like
most other registers. Any data written into the status
Rev. 1.60
M O D E
8
April 28, 2010
HT48R52A
Bit No.
Label
Function
0
C
C is set if an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation, otherwise C is cleared. C is also affected by a
rotate through carry instruction.
1
AC
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow
from the high nibble into the low nibble in subtraction, otherwise AC is cleared.
2
Z
Z is set if the result of an arithmetic or logic operation is zero, otherwise Z is cleared.
3
OV
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa, otherwise OV is cleared.
4
PDF
PDF is cleared by system power-up or executing the ²CLR WDT² instruction. PDF is set by
executing the ²HALT² instruction.
5
TO
TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction.
TO is set by a WDT time-out.
6, 7
¾
Unused bit, read as ²0²
STATUS (0AH) Register
Interrupt
An external interrupt is triggered either on a high to low
or low to high transition on the INT pin. The related interrupt request flag, EIF; bit 4 of the INTC register will then
be set. When the interrupt is enabled, the stack is not full
and the external interrupt is active, a subroutine call to
location 04H will occur. The interrupt request flag (EIF)
and EMI bits will be cleared to disable other interrupts.
The device provides an external interrupt and internal
timer/event counter interrupt. The Interrupt Control Register (INTC;0BH) contains the interrupt control bits to set
the enable or disable bits and the interrupt request flags.
Once an interrupt subroutine is serviced, all the other interrupts will be blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
interrupt requests may occur during this interval but only
the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the
EMI bit and the corresponding bit of the INTC may be set
to allow interrupt nesting. If the stack is full, the interrupt
request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack must be prevented from
becoming full.
The internal timer/event counter interrupt is initialised by
setting the timer/event counter interrupt request flag,
TF; bit 5 of the INTC register. This will be caused by a
timer overflow. When the interrupt is enabled, the stack
is not full and the TF bit is set, a subroutine call to location 08H will occur. The related interrupt request flag,
TF, will then be reset and the EMI bit cleared to disable
further interrupts.
During the execution of an interrupt subroutine, other interrupt acknowledge signals are held until the ²RETI² instruction is executed or the EMI bit and the related
interrupt control bit are set to 1, if the stack is not full. To
return from the interrupt subroutine, a ²RET² or ²RETI²
instruction may be invoked. RETI will set the EMI bit to
enable an interrupt service, but RET will not.
All interrupts have a wake-up capability. When an interrupt is serviced, a control transfer occurs by pushing the
program counter onto the stack, followed by a branch to
a subroutine at specified location in the program memory. Only the program counter is pushed onto the stack.
If the contents of the register or status register are altered by the interrupt service program, an action which
may corrupt the desired control sequence, the contents
should be saved in advance.
Bit No.
Label
0
EMI
Controls the master (global) interrupt (1=enable; 0=disable)
Function
1
EEI
Controls the external interrupt (1=enable; 0=disable)
2
ETI
Controls the Timer/Event Counter 0 interrupt (1=enable; 0=disable)
3, 6, 7
¾
Unused bit, read as ²0²
4
EIF
External interrupt request flag (1=active; 0=inactive)
5
TF
Internal Timer/Event Counter 0 request flag (1=active; 0=inactive)
INTC (0BH) Register
Rev. 1.60
9
April 28, 2010
HT48R52A
V
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests
the following table shows the priority that is applied.
These can be masked by resetting the EMI bit.
Interrupt Source
Priority
Vector
External Interrupt
1
04H
Timer/Event Counter Overflow
2
08H
4 7 0 p F
O S C 1
R
The WDT oscillator is a free running on-chip RC oscillator, and requires no external components. Although
when the system enters the power down mode, the system clock stops, the WDT oscillator will keep running
with a period of approximately 65ms at 5V. The WDT oscillator can be disabled by a configuration option to conserve power.
Watchdog Timer - WDT
The WDT clock source is implemented by a internal WDT
OSC, the external 32768Hz (fRTC) or the instruction clock
(system clock divided by 4), the choice of which is determined by configuration option. This timer is designed to
prevent software malfunctions or sequences jumping to
an unknown location with unpredictable results. The
Watchdog can be disabled by a configuration option. If
the Watchdog Timer is disabled, all the executions related to WDT will result in no operation.
If the device operates in a noisy environment, using the
on-chip WDT OSC or 32768Hz crystal oscillator is
strongly recommended.
If an RC oscillator is used, an external resistor, whose
resistance must range from 100kW to 2MW, should be
connected between OSC1 and VSS. The RC oscillator
provides the most cost effective solution, however, the
frequency of oscillation may vary with VDD, temperatures and the chip itself due to process variations. It is,
therefore, not suitable for timing sensitive operations
where an accurate oscillator frequency is desired.
When the WDT clock source is selected, it will be first divided by 16 (4-stage), and then divided by the TMRC
prescaler (8-stage), after that, divided by 512 (9-stage)
to get the nominal time-out period. By using the TMRC
prescaler, longer time-out periods can be realized. Writing data to PSC2, PSC1, PSC0 can give different
time-out periods. The WDT OSC period is 65ms. This
time-out period may vary with temperature, VDD and
process variations. The WDT OSC keep running in any
operation mode.
The other oscillator circuit is designed for the real time
clock. For this device, only a 32768Hz crystal oscillator
can be used. The crystal should be connected between
OSC3 and OSC4.
If the instruction clock (system clock/4) is selected as
the WDT clock source, the WDT operates in the same
manner.
The RTC oscillator circuit can be controlled to start up
quickly by setting the ²QOSC² bit (bit 4 of mode). It is
fS
4 - B it D iv id e r
3 2 7 6 8 H z
C r y s ta l O s c illa to r
recommended to turn on the quick oscillating function at
power on until the RTC oscillator is stable, and then turn
it off after 2 seconds to reduce power consumption.
These devices provide two types of system oscillator circuits, an RC oscillator and a 32768Hz crystal oscillator,
the choice of which is determined by software.
O p tio n
S e le c t
O s c illa to r
System Oscillator
Oscillator Configuration
C lo c k /4
1 0 p F
R C
It is recommended that a program does not use the
²CALL subroutine² within the interrupt subroutine. Interrupts often occur in an unpredictable manner or need to
be serviced immediately in some applications. If only one
stack is left and enabling the interrupt is not well controlled, the original control sequence will be damaged if a
²CALL² is executed in the interrupt subroutine.
3 2 7 6 8 H z
O S C 3
O S C
O S C 4
The timer/event counter interrupt request flag, TF, external interrupt request flag, EIF, enable timer/event counter interrupt bit, ET, enable external interrupt bit, EEI,
and enable master interrupt bit, EMI, constitute an interrupt control register, INTC, which is located at 0BH in the
data memory. EMI, EEI, ETI are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the
interrupt request flags, TF and EIF, are set, they will remain in the INTC register until the interrupts are serviced or cleared by a software instruction.
S y s te m
D D
8 - S ta g e P r e s c a le r
W D T O S C
8 -to -1 M U X
P S C 2 ~ P S C 0
9 - B it C o u n te r
W D T T im e - o u t
Watchdog Timer
Rev. 1.60
10
April 28, 2010
HT48R52A
be active depending on the configuration option ²WDT²
instruction. If the ²CLR WDT² is selected (i.e. One clear
instruction), any execution of the CLR WDT instruction
will clear the WDT. In the case that ²CLR WDT1² and
²CLR WDT2² are chosen (i.e. two clear instructions),
these two instructions must be executed to clear the
WDT; otherwise, the WDT may reset the chip as a result
of a time-out.
If the WDT clock source is the 32768Hz, the WDT also
operates in the same manner.
The WDT time-out under normal mode or slow mode will
initialize a ²chip reset² and set the status bit ²TO². But in
the idle mode, that is after a HALT instruction is executed, the time-out will initialize a ²warm reset² and only
the program counter and stack pointer are reset to 0.
To clear the WDT contents (not including the 4-bit divider and the 8-stage prescaler), three methods are
adopted; an external reset (a low level to RES pin), software instruction and a ²HALT² instruction.
Operation Mode
The device support two system clocks and three operation modes. The system clock can be either an RC oscillator or a 32768Hz RTC. The three operational modes
are, Normal, Slow, or Idle mode. These are all selected
by software.
The software instruction includes a ²CLR WDT² instruction, and the instruction pair ²CLR WDT1² and ²CLR
WDT2². Of these two types of instruction, only one can
Bit No.
Label
Function
0
MODS
System clock high/low mode select bit
0= RC system clock select
1= 32768Hz system clock select and RC system clock stop
Note that if the 32768Hz system clock is selected, then the WDT clock source configuration option must also select the 32768Hz oscillator as its clock source, otherwise unpredictable system operation may occur.
1, 2, 3
¾
4
QOSC
5, 6, 7
¾
Unused bit, read as ²0²
32768Hz OSC quick start-up
0=quick start; 1=slow start
Unused bit, read as ²0²
MODE (20H) Register
Mode
System Clock
HALT Instruction
MODS
RC Oscillator
32768Hz
Normal
RC oscillator
No Executed
0
On
On
Slow
32768Hz
No Executed
1
Off
On
Idle
HALT
Be executed
x
Off
On
Operation Mode
Power Down Operation - HALT
forms a ²warm reset². After the TO and PDF flags are
examined, the reason behind the reset can be determined. The PDF flag is cleared by a system power-up or
executing the ²CLR WDT² instruction and is set when
executing the ²HALT² instruction. The TO flag is set if
the WDT time-out occurs, and causes a wake-up that
only resets the program counter and stack pointer, the
other circuits remain in their original status.
The HALT mode is entered using the ²HALT² instruction
and results in the following:
· The system oscillator will be turned off but the WDT
remains operational if its clock source is the internal
WDT oscillator.
· The contents of the on chip RAM and registers remain
unchanged.
· The WDT will be cleared. The WDT will resume counting, if the WDT clock souce is the internal WDT oscillator.
· All of the I/O ports will maintain their original status.
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each port
A pin can be independently selected to wake up the device via configuration options. If awakened by an I/O
port stimulus, the program will resume execution at the
next instruction. If awakened by an interrupt, two sequences may occur. If the related interrupt is disabled or
the interrupt is enabled but the stack is full, the program
will resume execution at the next instruction. If the interrupt is enabled and the stack is not full, the regular inter-
· The PDF flag will be set and the TO flag will be cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge signal on port A or a WDT overflow. An external reset
causes a device initialization and the WDT overflow per-
Rev. 1.60
11
April 28, 2010
HT48R52A
To guarantee that the system oscillator is running and
stable, the SST (System Start-up Timer) provides an extra delay of 1024 system clock pulses when the system
reset (power-up, WDT time-out or RES reset) or when
the system awakes from the HALT state.
rupt response takes place. If an interrupt request flag is
set to ²1² before entering the HALT mode, the wake-up
function of the related interrupt will be disabled. Once a
wake-up event occurs, it takes 1024 system clock periods to resume normal operation. In other words, a
dummy period will be inserted after a wake-up. If the
wake-up results from an interrupt acknowledge signal,
the actual interrupt subroutine execution will be delayed
by one or more cycles. If the wake-up results in the next
instruction execution, this will be executed immediately
after the dummy period is finished.
When a system reset occurs, the SST delay is added
during the reset period. Any wake-up from HALT will enable the SST delay.
An extra option load time delay is added during a system
reset (power-up, WDT time-out at normal mode or RES
reset).
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
The RTC oscillator will keep running when the device is
in the HALT mode, if the RTC oscillator is enabled.
The functional unit chip reset status are shown below.
Reset
Program Counter
000H
Interrupt
Disable
Prescaler
Clear
WDT
Clear. After master reset,
WDT begins counting
There are three ways in which a reset can occur:
· RES reset during normal operation
· RES reset during HALT
Timer/Event Counter Off
· WDT time-out reset during normal operation
A the time-out during a HALT is different from the other
chip reset conditions, since it can perform a ²warm re set² that resets only the program counter and SP, leaving the other circuits in their original state. Some registers remain unchanged during other reset conditions.
Most registers are reset to their ²initial condition² when
the reset conditions are met. By examining the PDF and
TO flags, the program can distinguish between different
²chip resets².
TO PDF
Input/Output Ports
Input mode
Stack Pointer
Points to the top of the stack
V D D
R E S
tS
S T
S S T T im e - o u t
C h ip
RESET Conditions
R e s e t
Reset Timing Chart
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
V
D D
0 .0 1 m F *
1 0 0 k W
R E S
Note: ²u² stands for ²unchanged²
1 0 k W
0 .1 m F *
H A L T
W a rm
R e s e t
Reset Circuit
W D T
Note:
R E S
O S C 1
S S T
1 0 - b it R ip p le
C o u n te r
S y s te m
C o ld
R e s e t
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to
avoid noise interference.
R e s e t
Reset Configuration
Rev. 1.60
12
April 28, 2010
HT48R52A
The states of the registers are summarised in the table.
Reset
(Power On)
WDT Time-out
(Normal Operation)
RES Reset
(Normal Operation)
RES Reset
(HALT)
WDT Time-out
(HALT)*
MP0
-xxx xxxx
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
MP1
-xxx xxxx
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
PCL
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
Register
TBLH
--xx xxxx
--uu uuuu
--uu uuuu
--uu uuuu
--uu uuuu
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
INTC
--00 -000
--00 -000
--00 -000
--00 -000
--uu -uuu
TMR
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMRC
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u uuuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PBC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PC
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
PD
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PE
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
---0 ---0
---0 ---0
---0 ---0
---0 ---0
---u ---u
MODE
Note:
²*² stands for ²warm reset²
²u² stands for ²unchanged²
²x² stands for ²unknown²
There are two registers related to the timer/event counter; TMR ([0DH]) and TMRC ([0EH]). Two physical registers are mapped to the TMR register location. Writing
to TMR places the start value in the timer/event counter
preload register while reading the TMR register retrieves the contents of the timer/event counter. The
TMRC regiser is a timer/event counter control register
which defines some options.
Timer/Event Counter
A single Timer/event counter is implemented in the
microcontroller. The timer/event counter contains an 8-bit
programmable count-up counter whose clock may be
sourced from an external source or from the system
clock/4 or fSP.
The fSP clock source is implemented by the WDT OSC,
an external 32768Hz (fRTC) or an instruction clock (system clock divided by 4), determined by configuration option. If one of these three source is selected, it will be
first divided by 16 (4-stage), and then divided by the
TMRC prescaler (8-stage) to get an fSP output period.
By using the TMRC prescaler, longer time-out periods
can be realized. Writing data to PSC2, PSC1, PSC0 can
give different fSP output periods.
The TM0, TM1 bits define the operating mode. The
event count mode is used to count external events,
which means the clock source must comes from the external timer pin, TMR. The timer mode functions as a
normal timer with the clock source coming from the fINT
clock. The pulse width measurement mode can be used
to count the duration of a high or low-level signal on the
external timer pin, TMR. The counting is based on the
fINT clock.
Using internal clock sources, there are 2 reference
time-bases for the timer/event counter. The internal
clock source can be sourced from fSYS/4 or fSP via a configuration options. Using an external clock input allows
the user to count external events, measure time
intervals or pulse widths, or generate an accurate time
base, while using the internal clock allows the user to
generate an accurate time base.
Rev. 1.60
In the event count or timer mode, once the timer/event
counter is enabled, it begins counting form the value
placed in the timer/event counter. From this initial value
it will count up to a value of FFH. Once an overflow occurs, the counter is reloaded from the timer/event counter preload register and at the same time generates the
interrupt request flag, TF; bit 5 of the INTC.
13
April 28, 2010
HT48R52A
mode, the TON will be cleared automatically after the
measurement cycle is completed. But in the other two
modes the TON can only be reset by instructions. The
overflow of the timer/event counter is one of the
wake-up sources. No matter what the operation mode
is, writing a 0 to ETI can disable the corresponding interrupt services.
In the pulse width measurement mode with the TON and
TE bits equal to one, once it goes from low to high (or
high to low if the TE bits is ²0²) it will start counting until
the TMR returns to the original level and resets the TON.
The measured result will remain in the timer/event counter even if the activated transient occurs again. In other
words, only one cycle measurement can be done. Until
setting the TON, the cycle measurement will function
again as long as it receives further transient pulse. Note
that, in this operating mode, the timer/event counter
starts counting not according to the logic level but according to the transient edges. In the case of counter
overflows, the counter is reloaded from the timer/event
counter preload register and issues the interrupt request
just like the other two modes. To enable the counting operation, the timer ON bit (TON; bit 4 of the TMRC)
should be set to 1. In the pulse width measurement
fS Y S /4
R T C O S C
W D T O S C
M
U
fS
X
4 - b it D iv id e r
fS /1 6
(1 /2 ~ 1 /2 5 6 )
8 - s ta g e P r e s c a le r
fS
fS
8 -1 M U X
M a s k O p tio n
P S C 2 ~ P S C 0
9 - B it C o u n te r
/4
Y S
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register will also
reload that data to the timer/event counter. But if the
timer/event counter is turned on, data written to it will
only be kept in the timer/event counter preload register.
The timer/event counter will still operate until overflow
occurs (a timer/event counter reloading will occur at the
same time). When the timer/event counter (reading
TMR) is read, the clock will be blocked to avoid errors.
M
P
U
f IN
W D T T im e - o u t
T
D a ta B u s
X
T M 1
T M 0
M a s k O p tio n
8 - B it T im e r /E v e n t
C o u n te r P r e lo a d R e g is te r
T M R
R e lo a d
T E
T M 1
T M 0
T O N
8 - B it T im e r /E v e n t
C o u n te r (T M R )
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
O v e r flo w
to In te rru p t
Timer/Event Counter and WDT
Bit No.
0
1
2
Label
PSC0
PSC1
PSC2
3
TE
4
TON
5
¾
6
7
TM0
TM1
Function
Define the prescaler stages, PSC2, PSC1, PSC0=
000: fSP=fS/32
001: fSP=fS/64
010: fSP=fS/128
011: fSP=fS/256
100: fSP=fS/512
101: fSP=fS/1024
110: fSP=fS/2048
111: fSP=fS/4096
Defines the TMR active edge of the timer/event counter:
In Event Counter Mode (TM1,TM0)=(0,1):
1:count on falling edge;
0:count on rising edge
In Pulse Width measurement mode (TM1,TM0)=(1,1):
1: start counting on the rising edge, stop on the falling edge;
0: start counting on the falling edge, stop on the rising edge
To enable or disable timer 0 counting
(0=disable; 1=enable)
Unused bit, read as ²0²
Define the operating mode, TM1, TM0=
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
TMRC (0EH) Register
Rev. 1.60
14
April 28, 2010
HT48R52A
register to high will force PC to output high state.
As clock blocking may result in a counting error, this
must be taken into consideration by the programmer.
The bit2~bit0 of the TMRC can be used to define the
pre-scaling stages of the internal clock sources of the
timer/event counter. The definitions are as shown.
The external interrupt pin INT is pin-shard with output
pin PD0.
The PD and PE can be used for output operation only.
Setting its output register high which effectively places
its NMOS output transistor in high impedance state. Resetting output register to low will force to output low
state.
Input/Output Ports
There are 16 bidirectional input/output (PA, PB) lines
and 8 PMOS (PC), 16 NMOS (PD, PE) output lines in
the microcontroller, labeled from PA to PE, which are
mapped to the data memory of [12H], [14H], [16H],
[18H] and [1AH] respectively. All pins on PA~PB can be
used for both input and output operations.
After a chip reset, these input/output lines remain at high
levels or floating state (depending on the pull-high options). Each bit of these input/output latches can be set
or cleared by ²SET [m].i² and ²CLR [m].i² (m=12H, 14H,
16H, 18H or 1AH) instructions.
For the input operation, these ports are non-latching,
that is, the inputs must be ready at the T2 rising edge of
instruction ²MOV A,[m]² (m=12H, 14H). For output operation, all the data is latched and remains unchanged until the output latch is rewritten.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²LR [m].i²,
²CPL [m]², ²CPLA [m]² read the entire port states into
the CPU, execute the defined operations (bit-operation),
and then write the results back to the latches or the accumulator.
The PA and PB have their own control registers (PAC,
PBC) to control the input/output configuration. These
two control registers are mapped to locations 13H and
15H. CMOS/PMOS output or Schmitt trigger input with
structures can be reconfigured dynamically under software control. The control registers specifies which pin
are set as input and which are set as outputs. To setup a
pin as an input the corresponding bit of the control register must be set high, for an output it must be set low.
Each line of port A has the capability of waking-up the
device.
There is a pull-high option available for PA0~PA7 lines
(port option). Once the pull-high option of an I/O line is
selected, the I/O line have pull-high resistor. Otherwise,
the pull-high resistor is absent. It should be noted that a
non-pull-high I/O line operating in input mode will cause
a floating state.
The PC can be used for output operation only. Resetting
its output register to low will effectively places its PMOS
output transistor in high impedance state. Setting output
V
D a ta B u s
W r ite C o n tr o l R e g is te r
D D
P u ll- H ig h
O p tio n
C o n tr o l B it
Q
D
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
W r ite D a ta R e g is te r
P A 0 ~ P A 7
D a ta B it
Q
D
C K
S
Q
M
R e a d D a ta R e g is te r
S y s te m
U
X
W a k e -u p
W a k e - u p O p tio n
PA Input/Output Port
Rev. 1.60
15
April 28, 2010
HT48R52A
V
C o n tr o l B it
Q
D
D a ta B u s
W r ite C o n tr o l R e g is te r
D D
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
D a ta B it
Q
D
W r ite D a ta R e g is te r
C K
S
P B 0 ~ P B 7
Q
M
R e a d D a ta R e g is te r
P B 3 /T M R in p u t
U
X
PB Input/Output Port
V
D D
D a ta B it
D a ta B u s
W r ite D a ta R e g is te r
Q
D
C K
Q
R
C h ip R e s e t
P C 0 ~ P C 7
R e a d D a ta R e g is te r
PC Output Port
P D 0 /IN T
D a ta B it
D a ta B u s
W r ite D a ta R e g is te r
Q
D
C K
S
Q
C h ip R e s e t
R e a d D a ta R e g is te r
IN T In p u t
PD0 Input/Output Port
P D 1 ~ P D 7
P E 0 ~ P E 7
D a ta B it
D a ta B u s
W r ite D a ta R e g is te r
Q
D
C K
S
Q
C h ip R e s e t
R e a d D a ta R e g is te r
PD1~PD7, PE Output Ports
Rev. 1.60
16
April 28, 2010
HT48R52A
Low Voltage Reset - LVR
The relationship between VDD and VLVR is shown below.
The microcontroller provides a low voltage reset circuit
in order to monitor the supply voltage of the device. If the
supply voltage of the device is within the range
0.9V~VLVR, such as changing a battery, the LVR will automatically reset the device internally.
V D D
5 .5 V
V
O P R
5 .5 V
The LVR includes the following specifications:
V
2 .2 V
original state for more than 1ms. If the low voltage
state does not exceed 1ms, the LVR will ignore it and
do not perform a reset function.
· The LVR uses the ²OR² function with the external
0 .9 V
RES signal to perform a chip reset.
V
L V R
3 .0 V
· The low voltage (0.9V~VLVR) has to remain in their
Note:
VOPR is the voltage range for proper chip operation at 4MHz system clock.
D D
5 .5 V
V
L V R
L V R
D e te c t V o lta g e
0 .9 V
0 V
R e s e t S ig n a l
R e s e t
N o r m a l O p e r a tio n
*1
R e s e t
*2
Low Voltage Reset
Note:
*1: To make sure that the system oscillator has stabilized, the SST provides an extra delay of
1024 system clock pulses before entering the normal operation.
*2: Since a low voltage has to be maintained for more than 1ms, therefore a 1ms delay is provided before
entering the reset mode.
Options
The following table shows all kinds of options in the microcontroller. All of the options must be defined to ensure having
a proper functioning system.
Items
Options
1
PA0~PA7 bit wake-up enable or disable (by bit)
2
PA pull-high enable or disable (by port)
3
WDT clock source: WDT oscillator or fSYS/4 or 32768Hz oscillator
4
WDT enable or disable
5
CLRWDT instructions: 1 or 2 instructions
6
Timer/event counter clock sources: fSYS/4 or fSP
7
LVR enable or disable
Rev. 1.60
17
April 28, 2010
HT48R52A
Application Circuits
V
D D
0 .0 1 m F *
V D D
1 0 0 k W
0 .1 m F
R E S
P A 0 ~ P A 7
V S S
P B 0 ~ P B 2
P B 3 /T M R
P B 4 ~ P B 7
1 0 k W
0 .1 m F *
V
P C 0 ~ P C 7
D D
P D 0 /IN T
P D 1 ~ P D 7
4 7 0 p F
O S C 1
1 0 0 k W ~
2 M W
P E 0 ~ P E 7
T E S T
3 2 7 6 8 H z
O S C 3
1 0 p F
O S C 4
H T 4 8 R 5 2 A
Note:
The resistance and capacitance for the reset circuit should be chosen in such a way as to ensure that VDD is
stable and remains within a valid operating voltage range before bringing RES high.
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to avoid noise
interference.
Rev. 1.60
18
April 28, 2010
HT48R52A
Instruction Set
sure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for subtraction. The increment and decrement instructions
INC, INCA, DEC and DECA provide a simple means of
increasing or decreasing by a value of one of the values
in the destination specified.
Introduction
C e n t ra l t o t he s uc c es s f ul oper a t i on o f a n y
microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to
perform certain operations. In the case of Holtek
microcontrollers, a comprehensive and flexible set of
over 60 instructions is provided to enable programmers
to implement their application with the minimum of programming overheads.
Logical and Rotate Operations
The standard logical operations such as AND, OR, XOR
and CPL all have their own instruction within the Holtek
microcontroller instruction set. As with the case of most
instructions involving data manipulation, data must pass
through the Accumulator which may involve additional
programming steps. In all logical data operations, the
zero flag may be set if the result of the operation is zero.
Another form of logical data manipulation comes from
the rotate instructions such as RR, RL, RRC and RLC
which provide a simple means of rotating one bit right or
left. Different rotate instructions exist depending on program requirements. Rotate instructions are useful for
serial port programming applications where data can be
rotated from an internal register into the Carry bit from
where it can be examined and the necessary serial bit
set high or low. Another application where rotate data
operations are used is to implement multiplication and
division calculations.
For easier understanding of the various instruction
codes, they have been subdivided into several functional groupings.
Instruction Timing
Most instructions are implemented within one instruction cycle. The exceptions to this are branch, call, or table read instructions where two instruction cycles are
required. One instruction cycle is equal to 4 system
clock cycles, therefore in the case of an 8MHz system
oscillator, most instructions would be implemented
within 0.5ms and branch or call instructions would be implemented within 1ms. Although instructions which require one more cycle to implement are generally limited
to the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other instructions
which involve manipulation of the Program Counter Low
register or PCL will also take one more cycle to implement. As instructions which change the contents of the
PCL will imply a direct jump to that new address, one
more cycle will be required. Examples of such instructions would be ²CLR PCL² or ²MOV PCL, A². For the
case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then
this will also take one more cycle, if no skip is involved
then only one cycle is required.
Branches and Control Transfer
Program branching takes the form of either jumps to
specified locations using the JMP instruction or to a subroutine using the CALL instruction. They differ in the
sense that in the case of a subroutine call, the program
must return to the instruction immediately when the subroutine has been carried out. This is done by placing a
return instruction RET in the subroutine which will cause
the program to jump back to the address right after the
CALL instruction. In the case of a JMP instruction, the
program simply jumps to the desired location. There is
no requirement to jump back to the original jumping off
point as in the case of the CALL instruction. One special
and extremely useful set of branch instructions are the
conditional branches. Here a decision is first made regarding the condition of a certain data memory or individual bits. Depending upon the conditions, the program
will continue with the next instruction or skip over it and
jump to the following instruction. These instructions are
the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data bits.
Moving and Transferring Data
The transfer of data within the microcontroller program
is one of the most frequently used operations. Making
use of three kinds of MOV instructions, data can be
transferred from registers to the Accumulator and
vice-versa as well as being able to move specific immediate data directly into the Accumulator. One of the most
important data transfer applications is to receive data
from the input ports and transfer data to the output ports.
Arithmetic Operations
The ability to perform certain arithmetic operations and
data manipulation is a necessary feature of most
microcontroller applications. Within the Holtek
microcontroller instruction set are a range of add and
subtract instruction mnemonics to enable the necessary
arithmetic to be carried out. Care must be taken to en-
Rev. 1.60
19
April 28, 2010
HT48R52A
Bit Operations
Other Operations
The ability to provide single bit operations on Data Memory is an extremely flexible feature of all Holtek
microcontrollers. This feature is especially useful for
output port bit programming where individual bits or port
pins can be directly set high or low using either the ²SET
[m].i² or ²CLR [m].i² instructions respectively. The feature removes the need for programmers to first read the
8-bit output port, manipulate the input data to ensure
that other bits are not changed and then output the port
with the correct new data. This read-modify-write process is taken care of automatically when these bit operation instructions are used.
In addition to the above functional instructions, a range
of other instructions also exist such as the ²HALT² instruction for Power-down operations and instructions to
control the operation of the Watchdog Timer for reliable
program operations under extreme electric or electromagnetic environments. For their relevant operations,
refer to the functional related sections.
Instruction Set Summary
The following table depicts a summary of the instruction
set categorised according to function and can be consulted as a basic instruction reference using the following listed conventions.
Table Read Operations
Table conventions:
Data storage is normally implemented by using registers. However, when working with large amounts of
fixed data, the volume involved often makes it inconvenient to store the fixed data in the Data Memory. To overcome this problem, Holtek microcontrollers allow an
area of Program Memory to be setup as a table where
data can be directly stored. A set of easy to use instructions provides the means by which this fixed data can be
referenced and retrieved from the Program Memory.
Mnemonic
x: Bits immediate data
m: Data Memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Description
Cycles
Flag Affected
1
1Note
1
1
1Note
1
1
1Note
1
1Note
1Note
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
C
1
1
1
1Note
1Note
1Note
1
1
1
1Note
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
1
1Note
1
1Note
Z
Z
Z
Z
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Add Data Memory to ACC
Add ACC to Data Memory
Add immediate data to ACC
Add Data Memory to ACC with Carry
Add ACC to Data memory with Carry
Subtract immediate data from the ACC
Subtract Data Memory from ACC
Subtract Data Memory from ACC with result in Data Memory
Subtract Data Memory from ACC with Carry
Subtract Data Memory from ACC with Carry, result in Data Memory
Decimal adjust ACC for Addition with result in Data Memory
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
Logical AND Data Memory to ACC
Logical OR Data Memory to ACC
Logical XOR Data Memory to ACC
Logical AND ACC to Data Memory
Logical OR ACC to Data Memory
Logical XOR ACC to Data Memory
Logical AND immediate Data to ACC
Logical OR immediate Data to ACC
Logical XOR immediate Data to ACC
Complement Data Memory
Complement Data Memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rev. 1.60
Increment Data Memory with result in ACC
Increment Data Memory
Decrement Data Memory with result in ACC
Decrement Data Memory
20
April 28, 2010
HT48R52A
Mnemonic
Description
Cycles
Flag Affected
Rotate Data Memory right with result in ACC
Rotate Data Memory right
Rotate Data Memory right through Carry with result in ACC
Rotate Data Memory right through Carry
Rotate Data Memory left with result in ACC
Rotate Data Memory left
Rotate Data Memory left through Carry with result in ACC
Rotate Data Memory left through Carry
1
1Note
1
1Note
1
1Note
1
1Note
None
None
C
C
None
None
C
C
Move Data Memory to ACC
Move ACC to Data Memory
Move immediate data to ACC
1
1Note
1
None
None
None
Clear bit of Data Memory
Set bit of Data Memory
1Note
1Note
None
None
Jump unconditionally
Skip if Data Memory is zero
Skip if Data Memory is zero with data movement to ACC
Skip if bit i of Data Memory is zero
Skip if bit i of Data Memory is not zero
Skip if increment Data Memory is zero
Skip if decrement Data Memory is zero
Skip if increment Data Memory is zero with result in ACC
Skip if decrement Data Memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1Note
1note
1Note
1Note
1Note
1Note
1Note
1Note
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read table (current page) to TBLH and Data Memory
Read table (last page) to TBLH and Data Memory
2Note
2Note
None
None
No operation
Clear Data Memory
Set Data Memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of Data Memory
Swap nibbles of Data Memory with result in ACC
Enter power down mode
1
1Note
1Note
1
1
1
1Note
1
1
None
None
None
TO, PDF
TO, PDF
TO, PDF
None
None
TO, PDF
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
1. For skip instructions, if the result of the comparison involves a skip then two cycles are required,
if no skip takes place only one cycle is required.
2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution.
3. For the ²CLR WDT1² and ²CLR WDT2² instructions the TO and PDF flags may be affected by
the execution status. The TO and PDF flags are cleared after both ²CLR WDT1² and
²CLR WDT2² instructions are consecutively executed. Otherwise the TO and PDF flags
remain unchanged.
Rev. 1.60
21
April 28, 2010
HT48R52A
Instruction Definition
ADC A,[m]
Add Data Memory to ACC with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the Accumulator.
Operation
ACC ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADCM A,[m]
Add ACC to Data Memory with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADD A,[m]
Add Data Memory to ACC
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
ADD A,x
Add immediate data to ACC
Description
The contents of the Accumulator and the specified immediate data are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + x
Affected flag(s)
OV, Z, AC, C
ADDM A,[m]
Add ACC to Data Memory
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
AND A,[m]
Logical AND Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
Z
AND A,x
Logical AND immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical AND
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
Z
ANDM A,[m]
Logical AND ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
Z
Rev. 1.60
22
April 28, 2010
HT48R52A
CALL addr
Subroutine call
Description
Unconditionally calls a subroutine at the specified address. The Program Counter then increments by 1 to obtain the address of the next instruction which is then pushed onto the
stack. The specified address is then loaded and the program continues execution from this
new address. As this instruction requires an additional operation, it is a two cycle instruction.
Operation
Stack ¬ Program Counter + 1
Program Counter ¬ addr
Affected flag(s)
None
CLR [m]
Clear Data Memory
Description
Each bit of the specified Data Memory is cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
None
CLR [m].i
Clear bit of Data Memory
Description
Bit i of the specified Data Memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
None
CLR WDT
Clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT1
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT2 and must be executed alternately with CLR WDT2 to have effect. Repetitively executing this instruction without alternately executing CLR WDT2 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT2
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT1 and must be executed alternately with CLR WDT1 to have effect. Repetitively executing this instruction without alternately executing CLR WDT1 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
Rev. 1.60
23
April 28, 2010
HT48R52A
CPL [m]
Complement Data Memory
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa.
Operation
[m] ¬ [m]
Affected flag(s)
Z
CPLA [m]
Complement Data Memory with result in ACC
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa. The complemented result
is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
Z
DAA [m]
Decimal-Adjust ACC for addition with result in Data Memory
Description
Convert the contents of the Accumulator value to a BCD ( Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or
if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble
remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of
6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C
flag may be affected by this instruction which indicates that if the original BCD sum is
greater than 100, it allows multiple precision decimal addition.
Operation
[m] ¬ ACC + 00H or
[m] ¬ ACC + 06H or
[m] ¬ ACC + 60H or
[m] ¬ ACC + 66H
Affected flag(s)
C
DEC [m]
Decrement Data Memory
Description
Data in the specified Data Memory is decremented by 1.
Operation
[m] ¬ [m] - 1
Affected flag(s)
Z
DECA [m]
Decrement Data Memory with result in ACC
Description
Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] - 1
Affected flag(s)
Z
HALT
Enter power down mode
Description
This instruction stops the program execution and turns off the system clock. The contents
of the Data Memory and registers are retained. The WDT and prescaler are cleared. The
power down flag PDF is set and the WDT time-out flag TO is cleared.
Operation
TO ¬ 0
PDF ¬ 1
Affected flag(s)
TO, PDF
Rev. 1.60
24
April 28, 2010
HT48R52A
INC [m]
Increment Data Memory
Description
Data in the specified Data Memory is incremented by 1.
Operation
[m] ¬ [m] + 1
Affected flag(s)
Z
INCA [m]
Increment Data Memory with result in ACC
Description
Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] + 1
Affected flag(s)
Z
JMP addr
Jump unconditionally
Description
The contents of the Program Counter are replaced with the specified address. Program
execution then continues from this new address. As this requires the insertion of a dummy
instruction while the new address is loaded, it is a two cycle instruction.
Operation
Program Counter ¬ addr
Affected flag(s)
None
MOV A,[m]
Move Data Memory to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
None
MOV A,x
Move immediate data to ACC
Description
The immediate data specified is loaded into the Accumulator.
Operation
ACC ¬ x
Affected flag(s)
None
MOV [m],A
Move ACC to Data Memory
Description
The contents of the Accumulator are copied to the specified Data Memory.
Operation
[m] ¬ ACC
Affected flag(s)
None
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
No operation
Affected flag(s)
None
OR A,[m]
Logical OR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
Z
Rev. 1.60
25
April 28, 2010
HT48R52A
OR A,x
Logical OR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
Z
ORM A,[m]
Logical OR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²OR² [m]
Affected flag(s)
Z
RET
Return from subroutine
Description
The Program Counter is restored from the stack. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
Affected flag(s)
None
RET A,x
Return from subroutine and load immediate data to ACC
Description
The Program Counter is restored from the stack and the Accumulator loaded with the
specified immediate data. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
None
RETI
Return from interrupt
Description
The Program Counter is restored from the stack and the interrupts are re-enabled by setting the EMI bit. EMI is the master interrupt global enable bit. If an interrupt was pending
when the RETI instruction is executed, the pending Interrupt routine will be processed before returning to the main program.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
None
RL [m]
Rotate Data Memory left
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ [m].7
Affected flag(s)
None
RLA [m]
Rotate Data Memory left with result in ACC
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ [m].7
Affected flag(s)
None
Rev. 1.60
26
April 28, 2010
HT48R52A
RLC [m]
Rotate Data Memory left through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7
replaces the Carry bit and the original carry flag is rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RLCA [m]
Rotate Data Memory left through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces
the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in
the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RR [m]
Rotate Data Memory right
Description
The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into
bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ [m].0
Affected flag(s)
None
RRA [m]
Rotate Data Memory right with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data
Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ [m].0
Affected flag(s)
None
RRC [m]
Rotate Data Memory right through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0
replaces the Carry bit and the original carry flag is rotated into bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
C
RRCA [m]
Rotate Data Memory right through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is
stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
C
Rev. 1.60
27
April 28, 2010
HT48R52A
SBC A,[m]
Subtract Data Memory from ACC with Carry
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result
of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or
zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SBCM A,[m]
Subtract Data Memory from ACC with Carry and result in Data Memory
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SDZ [m]
Skip if decrement Data Memory is 0
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0 the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] - 1
Skip if [m] = 0
Affected flag(s)
None
SDZA [m]
Skip if decrement Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0, the program proceeds with the following instruction.
Operation
ACC ¬ [m] - 1
Skip if ACC = 0
Affected flag(s)
None
SET [m]
Set Data Memory
Description
Each bit of the specified Data Memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
None
SET [m].i
Set bit of Data Memory
Description
Bit i of the specified Data Memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
None
Rev. 1.60
28
April 28, 2010
HT48R52A
SIZ [m]
Skip if increment Data Memory is 0
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] + 1
Skip if [m] = 0
Affected flag(s)
None
SIZA [m]
Skip if increment Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0 the program proceeds with the following instruction.
Operation
ACC ¬ [m] + 1
Skip if ACC = 0
Affected flag(s)
None
SNZ [m].i
Skip if bit i of Data Memory is not 0
Description
If bit i of the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is 0 the program proceeds with the following instruction.
Operation
Skip if [m].i ¹ 0
Affected flag(s)
None
SUB A,[m]
Subtract Data Memory from ACC
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUBM A,[m]
Subtract Data Memory from ACC with result in Data Memory
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUB A,x
Subtract immediate data from ACC
Description
The immediate data specified by the code is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will
be set to 1.
Operation
ACC ¬ ACC - x
Affected flag(s)
OV, Z, AC, C
Rev. 1.60
29
April 28, 2010
HT48R52A
SWAP [m]
Swap nibbles of Data Memory
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged.
Operation
[m].3~[m].0 « [m].7 ~ [m].4
Affected flag(s)
None
SWAPA [m]
Swap nibbles of Data Memory with result in ACC
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged. The
result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC.3 ~ ACC.0 ¬ [m].7 ~ [m].4
ACC.7 ~ ACC.4 ¬ [m].3 ~ [m].0
Affected flag(s)
None
SZ [m]
Skip if Data Memory is 0
Description
If the contents of the specified Data Memory is 0, the following instruction is skipped. As
this requires the insertion of a dummy instruction while the next instruction is fetched, it is a
two cycle instruction. If the result is not 0 the program proceeds with the following instruction.
Operation
Skip if [m] = 0
Affected flag(s)
None
SZA [m]
Skip if Data Memory is 0 with data movement to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator. If the value is
zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the
program proceeds with the following instruction.
Operation
ACC ¬ [m]
Skip if [m] = 0
Affected flag(s)
None
SZ [m].i
Skip if bit i of Data Memory is 0
Description
If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is not 0, the program proceeds with the following instruction.
Operation
Skip if [m].i = 0
Affected flag(s)
None
TABRDC [m]
Read table (current page) to TBLH and Data Memory
Description
The low byte of the program code (current page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
TABRDL [m]
Read table (last page) to TBLH and Data Memory
Description
The low byte of the program code (last page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
Rev. 1.60
30
April 28, 2010
HT48R52A
XOR A,[m]
Logical XOR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XORM A,[m]
Logical XOR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XOR A,x
Logical XOR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Z
Rev. 1.60
31
April 28, 2010
HT48R52A
Package Information
44-pin QFP (10mm´10mm) Outline Dimensions
H
C
D
G
2 3
3 3
I
3 4
2 2
L
F
A
B
E
1 2
4 4
K
a
J
1
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
0.512
¾
0.528
B
0.390
¾
0.398
C
0.512
¾
0.528
D
0.390
¾
0.398
E
¾
0.031
¾
F
¾
0.012
¾
G
0.075
¾
0.087
H
¾
¾
0.106
I
0.010
¾
0.020
J
0.029
¾
0.037
K
0.004
¾
0.008
L
¾
0.004
¾
a
0°
¾
7°
Symbol
A
Rev. 1.60
1 1
Dimensions in mm
Min.
Nom.
Max.
13.00
¾
13.40
B
9.90
¾
10.10
C
13.00
¾
13.40
D
9.90
¾
10.10
E
¾
0.80
¾
F
¾
0.30
¾
G
1.90
¾
2.20
H
¾
¾
2.70
I
0.25
¾
0.50
J
0.73
¾
0.93
K
0.10
¾
0.20
L
¾
0.10
¾
a
0°
¾
7°
32
April 28, 2010
HT48R52A
44-pin LQFP (10mm´10mm) (FP3.2mm) Outline Dimensions
H
C
D
G
2 3
3 3
I
3 4
2 2
F
A
B
E
1 2
4 4
K
a
J
1
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
0.512
0.520
0.528
B
0.390
0.394
0.398
C
0.512
0.520
0.528
D
0.390
0.394
0.398
E
¾
0.031
¾
F
¾
0.012
¾
G
0.053
0.055
0.057
H
¾
¾
0.063
I
0.004
¾
0.010
J
0.041
0.047
0.053
K
0.004
¾
0.008
a
0°
¾
7°
Symbol
Rev. 1.60
1 1
Dimensions in mm
Min.
Nom.
Max.
A
13.00
13.20
13.40
B
9.90
10.00
10.10
C
13.00
13.20
13.40
D
9.90
10.00
10.10
E
¾
0.80
¾
F
¾
0.30
¾
G
1.35
1.40
1.45
H
¾
¾
1.60
I
0.10
¾
0.25
J
1.05
1.20
1.35
K
0.10
¾
0.25
a
0°
¾
7°
33
April 28, 2010
HT48R52A
52-pin QFP (14mm´14mm) Outline Dimensions
C
H
D
3 9
G
2 7
I
2 6
4 0
F
A
B
E
1 4
5 2
K
J
1
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
0.681
¾
0.689
B
0.547
¾
0.555
C
0.681
¾
0.689
D
0.547
¾
0.555
E
¾
0.039
¾
F
¾
0.016
¾
G
0.098
¾
0.122
H
¾
¾
0.134
I
¾
0.004
¾
J
0.029
¾
0.041
K
0.004
¾
0.008
L
¾
0.004
¾
a
0°
¾
7°
Symbol
Rev. 1.60
1 3
Dimensions in mm
Min.
Nom.
Max.
A
17.30
¾
17.50
B
13.90
¾
14.10
C
17.30
¾
17.50
D
13.90
¾
14.10
E
¾
1.00
¾
F
¾
0.40
¾
G
2.50
¾
3.10
H
¾
¾
3.40
I
¾
0.10
¾
J
0.73
¾
1.03
K
0.10
¾
0.20
a
0°
¾
7°
34
April 28, 2010
HT48R52A
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shenzhen Sales Office)
5F, Unit A, Productivity Building, No.5 Gaoxin M 2nd Road, Nanshan District, Shenzhen, China 518057
Tel: 86-755-8616-9908, 86-755-8616-9308
Fax: 86-755-8616-9722
Holtek Semiconductor (USA), Inc. (North America Sales Office)
46729 Fremont Blvd., Fremont, CA 94538, USA
Tel: 1-510-252-9880
Fax: 1-510-252-9885
http://www.holtek.com
Copyright Ó 2010 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.60
35
April 28, 2010