HOLTEK HT56R64

HT56R64
TinyPowerTM A/D Type with LCD 8-Bit OTP MCU
Technical Document
· Tools Information
· Application Note
- HA0075E MCU Reset and Oscillator Circuits Application Note
Features
· Operating voltage:
· Watchdog Timer function
fSYS=32768Hz: 2.2V~5.5V
fSYS=4MHz: 2.2V~5.5V
fSYS=8MHz: 3.0V~5.5V
fSYS=12MHz: 4.5V~5.5V
· PFD/Buzzer for audio frequency generation
· Dual Serial Interfaces: SPI and I2C
· LCD driver: 33´2, 33´3 or 32´4
· 4 operating modes: normal, slow, idle and sleep
· Operating current:
· 8-level subroutine nesting
fSYS=32kHz at 3.0V: 5mA (typ.)
fSYS=1MHz at 3.0V: 140mA (typ.)
· 8-channel 12-bit resolution A/D converter
· OTP Program Memory: 4K´15
· 4-channel 12-bit PWM output shared with I/O lines
· RAM Data Memory: 192´8
· Low voltage reset function - 2.1V, 3.15V, 4.2V
· 24 bidirectional I/O lines
· Low voltage detect function - 2.2V, 3.3V, 4.4V
· TinyPower technology for low power operation
· Bit manipulation instruction
· Three pin-shared external interrupts lines and
· 15-Bit table read instructions
· 63 powerful instructions
segment
· Single 8-bit programmable Timer/Event Counter
· Up to 0.33ms instruction cycle with 12MHz system
with overflow interrupt and 7-stage prescaler
clock at VDD=5V
· Single 16-bit programmable Timer/Event Counter
· All instructions executed in one or two machine
with overflow interrupt
cycles
· External Crystal, RC, RTC oscillator
· Power down and wake-up functions to reduce power
· Fully integrated 32kHz oscillator
consumption
· Externally supplied system clock option
· 52/100-pin QFP, 64-pin LQFP packages
General Description
The HT56R64 is a TinyPowerTM A/D Type with LCD 8-bit
high performance RISC architecture microcontroller, designed especially for applications that interface directly to
analog signals and which require an LCD interface. The
device includes an integrated multi-channel Analog to Digital Converter, four Pulse Width Modulation outputs and an
LCD driver.
wide range of products in the home appliance and industrial application areas. Some of these products
could include electronic metering, environmental monitoring, handheld instruments, electronically controlled
tools, motor driving in addition to many others.
The unique Holtek TinyPower technology also gives the
device extremely low current consumption characteristics, an extremely important consideration in the present
trend for low power battery powered applications. The
usual Holtek MCU features such as power down and
wake-up functions, oscillator options, programmable
frequency divider, etc. combine to ensure user applications require a minimum of external components.
With its fully integrated SPI and I2C functions, designers
are provided with a means of easy communication with
external peripheral hardware. The benefits of integrated
A/D, LCD, and PWM functions, in addition to low power
consumption, high performance, I/O flexibility and
low-cost, provides the device with the versatility for a
Rev. 1.40
1
September 8, 2009
HT56R64
Block Diagram
L o w
V o lta g e
D e te c t
W a tc h d o g
T im e r
W a tc h d o g
T im e r O s c illa to r
L o w
V o lta g e
R e s e t
R e s e t
C ir c u it
O T P
P r o g r a m m in g
C ir c u itr y
8 - b it
R IS C
M C U
C o re
O T P
P ro g ra m
M e m o ry
I/O
P o rts
R A M
D a ta
M e m o ry
In te rru p t
C o n tr o lle r
E x te rn a l
R C /C ry s ta l
O s c illa to r
S ta c k
In te rn a l R C
O s c illa to r
E x te rn a l R T C
O s c illa to r
A /D
C o n v e rte r
L C D
D r iv e r
I2C /S P I
P r o g r a m m a b le
F re q u e n c y
G e n e ra to r
T im e r s
P W M
G e n e ra to r
Pin Assignment
5
3 5
6
7
8
H T 5 6 R 6 4
5 2 Q F P -A
9
1 0
1 1
1 2
1 3
1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6
3 4
3 3
3 2
3 1
3 0
2 9
2 8
2 7
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
1 1 /S
1 2 /S
1 3 /S
1 4 /P
1 5 /P
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
P A
/A N
/A N
/A N
/A N
/A N
/A N
V S
0 /P W M
1 /P W M
2 /P W M
3 /P W M
D 4 /IN T
D 5 /IN T
6 /T M R
7 /T M R
P B 0
P B 1
P B 2
P B 3
P B 4
P B 5
D I/S D A
C K
C S
C L K
IN T
P D
P D
P D
P D
P
P
P D
P D
7
1
0
2
1
3
3
5
5
7
2
4
4
S
6
H T 5 6 R 6 4
6 4 L Q F P -B
8
0
9
1
1 0
2
1 1
3
1 2
1
0
1
0
1 3
1 4
1 5
1 6
1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1 3 2
4 8
4 7
4 6
4 5
4 4
4 3
4 2
4 1
4 0
3 9
3 8
3 7
3 6
3 5
3 4
3 3
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
9
8
1 0 /S
1 1 /S
1 2 /S
1 3 /S
1 4 /P
1 5 /P
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
D O
D I/S D A
C K /S C L
C S
C L K
IN T
2 4
2 5
2 6
2 7
2 8
2 9
3 /S E G 3 2
2
1
0
X
D 1
2
D 2
2 4
2 5
2 6
3 /S E G 3 2
2
1
0
X
D 1
/T M R 0
/IN T 1
/IN T 0
S E G
S E G
S E G
S E G
S E G
S E G
C O M
C O M
C O M
C O M
C 2
C 1
V L C
V 1
V M A
V L C
S E G
S E G
S E G
C O M
C O M
C O M
C O M
V 1
V M A
V L C
P D 6
P D 5
P D 4
Rev. 1.40
S
S
S
9
3 6
4
O
4
3
2
1
2
3 7
3
O
O
O
D
S
Z
Z
4
3 8
2
P A
E G 7
E G 6
E G 5
S C 4
S C 3
V D D
S C 2
S C 1
R E S
0 /B Z
1 /B Z
P A 2
/P F D
P A 4
P A 5
P A 6
O
6 4 6 3 6 2 6 1 6 0 5 9 5 8 5 7 5 6 5 5 5 4 5 3 5 2 5 1 5 0 4 9
D
P D 0 /P
P D 1 /P
P D 2 /P
1
3 9
P A
P A 3
S E G 1 0 /S D
S E G
O S C
O S C
V D
O S C
O S C
R E
P A 0 /B
P A 1 /B
P A
P A 3 /P F
P A
P B 0
P B 1
P B 2
P B 3
P B 4
P B 5
P A 5
P A 6
P A 7
/A N 0
/A N 1
/A N 2
/A N 3
/A N 4
/A N 5
V S S
W M 0
W M 1
W M 2
5 2 5 1 5 0 4 9 4 8 4 7 4 6 4 5 4 4 4 3 4 2 4 1 4 0
September 8, 2009
HT56R64
N
N
N
N
N
N
N
O S C
O S C
V D
V R E
A V D
O S C
O S C
R E
P A 0 /B
P A 1 /B
P A
P A 3 /P F
P A
C
C
C
C
C
C
C
D
D
D
S
F
Z
Z
P
P
4
P
3
P
2
1
P
2
4
P
1 0 0 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1
1
P A 5
P A 6
P A 7
N C
N C
N C
N C
P B 0 /A N 0
P B 1 /A N 1
P B 2 /A N 2
P B 3 /A N 3
P B 4 /A N 4
P B 5 /A N 5
P B 6 /A N 6
P B 7 /A N 7
V S S
A V S S
D 0 /P W M 0
D 1 /P W M 1
D 2 /P W M 2
D 3 /P W M 3
P D 4 /IN T 0
P D 5 /IN T 1
D 6 /T M R 0
D 7 /T M R 1
N C
N C
N C
N C
V L C D 1
2
8 0
7 9
3
7 8
4
7 7
5
7 6
6
7 5
7
7 4
8
7 3
9
7 2
1 0
7 1
1 1
1 2
1 3
1 4
H T 5 6 R 6 4
1 0 0 Q F P -A
1 5
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3 0
3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 4 0 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 0
7 0
6 9
6 8
6 7
6 6
6 5
6 4
6 3
6 2
6 1
6 0
5 9
5 8
5 7
5 6
5 5
5 4
5 3
5 2
5 1
N C
N C
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
S E
N C
N C
N C
N C
N C
N C
G 0
G 1
G 2
G 3
G 4
G 5
G 6
G 7
G 8
G 9
G 1 0
G 1 1
G 1 2
G 1 3
G 1 4
G 1 5
G 1 6
G 1 7
G 1 8
G 1 9
G 2 0
G 2 1
/S D
/S D
/S C
/S C
/P C
/P IN
O
I/S D A
K /S C L
S
L K
T
N C
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
C O M
C O M
C O M
C O M
C 2
C 1
V L C
V 1
V M A
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3 0
3 1
3 /S E G 3 2
2
1
0
D 2
X
Pin Description
Pin Name
PA0/BZ
PA1/BZ
PA2
PA3/PFD
PA4~PA7
PB0/AN0~
PB7/AN7
I/O
I/O
I/O
Configuration
Option
BZ/BZ
PFD
Description
Bidirectional 8-bit input/output port. Each individual bit on this port can be
configured as a wake-up input using the PAWU register. Software instructions determine if the pin is a CMOS output or Schmitt trigger input. A
pull-high resistor can be connected to each pin using the PAPU register.
Pins PA0, PA1 and PA3 are shared with BZ, BZ and PFD respectively, the
function of which is chosen via configuration option. Pins PA0~PA3 can
also be setup as open drain pins using the MISC register.
¾
Bidirectional 8-bit input/output port. Software instructions determine if the
pin is a CMOS output or Schmitt trigger input. A pull-high resistor can be
connected to each pin using the PBPU register. PB is pin-shared with the
A/D input pins. The A/D inputs are selected via software instructions.
Once selected as an A/D input, the I/O function and pull-high resistor
selections are disabled automatically.
PD0/PWM0~
PD3/PWM3
PD4/INT0
PD5/INT1
PD6/TMR0
PD7/TMR1
I/O
¾
Bidirectional 8-bit input/output port. Software instructions determine if the
pin is a CMOS output or Schmitt trigger input. A pull-high resistor can be
connected to each pin using the PDPU register. The PWM outputs,
PWM0~PWM3, are pin shared with pins PD0~PD3, the function of which
is chosen using the PWM registers. Pins PD4~PD7 are pin-shared with
INT0, INT1, TMR0 and TMR1 respectively.
COM0~COM2
COM3/SEG32
O
¾
COM2~COM0 are the LCD common outputs. A bit in the LCD Control
Register determines if pin COM3/SEG32 is configured as a segment
driver or as a common output driver.
Rev. 1.40
3
September 8, 2009
HT56R64
I/O
Configuration
Option
SEG31~SEG24
O
¾
LCD driver outputs for LCD panel segments.
SEG23~SEG16
O
¾
A bit in the LCD Control Register determines if the pins are to be used as
segment drivers or as CMOS outputs.
Pin Name
Description
SEG8~SEG9
SEG10/SDO
SEG11/SDI/SDA
SEG12/SCK/SCL
SEG13/SCS
SEG14/PCLK
SEG15/PINT
O
O
I/O
I/O
I/O
O
I/O
I 2C
SPI
PCLK
PINT
SEG8 and SEG9 are LCD driver outputs.
SEG10 is pin-shared with the Serial Interface Output line, SDO.
SEG11 is pin-shared with the SPI Bus data line, SDI and the I2C Bus data
line SDA.
SEG12, is pin-shared with the SPI Bus clock line, SCK, and the I2C Bus
clock line SCL.
SEG13 is pin-shared with the Serial Interface Select line, SCS.
SEG14 is pin-shared with the Peripheral Clock line, PCLK.
SEG15 is pin-shared with the Peripheral Interrupt line, PINT.
All of the SEG8~SEG15 lines can be chosen to be either segment drivers
or as logical outputs using LCD control bits.
SEG0~SEG7
O
¾
LCD driver outputs for LCD panel segments.
SEG0~SEG7 can be chosen to be either segment drivers or as logical
outputs using LCD control bits.
OSC1
OSC2
I
O
Crystal or RC
or EC
OSC1, OSC2 are connected to an external RC network or external crystal, determined by configuration option, for the internal system clock. If the
RC system clock option is selected, pin OSC2 can be used to measure the
system clock at 1/4 frequency. EC is external clock mode, we can input
clock source directly to OSC1 pin.
OSC3
OSC4
I
O
RTC
OSC3 and OSC4 are connected to a 32768Hz crystal oscillator to form a
real time clock for fSUB or fSL.
RES
I
¾
Schmitt Trigger reset input. Active low.
VLCD1
¾
¾
LCD power supply
VREF
I
¾
Reference voltage input pin.
VMAX
I
¾
IC maximum voltage, connect to VDD, VLCD or V1
V1, VLCD2, C1,
C2
I
¾
LCD voltage pump
VDD
¾
¾
Positive power supply
AVDD
¾
¾
Analog positive power supply.
VSS
¾
¾
Negative power supply, ground
AVSS
¾
¾
Analog negative power supply, ground
Note:
The Pin Description table represents the largest package available, therefore some of the pins and functions
may not be available on smaller package types.
Absolute Maximum Ratings
Supply Voltage ...........................VSS-0.3V to VSS+6.0V
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
IOL Total ..............................................................150mA
Total Power Dissipation .....................................500mW
Operating Temperature...........................-40°C to 85°C
IOH Total............................................................-100mA
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed
in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.40
4
September 8, 2009
HT56R64
D.C. Characteristics
Symbol
VDD
Parameter
Operating Voltage
Ta=25°C
Test Conditions
Min.
Typ.
Max.
Unit
fSYS=4MHz
2.2
¾
5.5
V
fSYS=8MHz
3.0
¾
5.5
V
fSYS=12MHz
4.5
¾
5.5
V
3.0
¾
5.0
V
¾
140
210
mA
¾
320
480
mA
¾
200
300
mA
¾
440
660
mA
¾
400
600
mA
¾
800
1200
mA
¾
320
480
mA
¾
550
820
mA
¾
300
450
mA
¾
530
800
mA
VDD
¾
Conditions
AVDD
Analog Operating Voltage
¾
VREF=AVDD
IDD1
Operating Current
(Crystal OSC, RC OSC)
3V
5V
No load, fSYS=fM=1MHz
ADC off
IDD2
Operating Current
(Crystal OSC, RC OSC)
5V
IDD3
Operating Current
(Crystal OSC, RC OSC)
IDD4
Operating Current
(EC Mode, Filter On)
3V
3V
5V
3V
5V
3V
No load, fSYS=fM=2MHz
ADC off
No load, fSYS=fM=4MHz
ADC off
No load, fSYS=fM=4MHz
ADC off
IDD5
Operating Current
(EC Mode, Filter Off)
IDD6
Operating Current
(Crystal OSC, RC OSC)
5V
No load, fSYS=fM=8MHz
ADC off
¾
1.5
3.0
mA
IDD7
Operating Current
(Crystal OSC, RC OSC)
5V
No load, fSYS=fM=12MHz
ADC off
¾
2.0
4.0
mA
Operating Current
(Slow Mode, fM=4MHz)
(Crystal OSC, RC OSC)
No load,
fSYS=fSLOW=500kHz
ADC off
¾
130
200
IDD8
mA
¾
300
450
mA
¾
170
260
mA
¾
370
560
mA
¾
250
380
mA
¾
520
780
mA
¾
220
330
mA
¾
480
720
mA
¾
300
450
mA
¾
630
950
mA
¾
460
690
mA
¾
920
1380
mA
No load, WDT off, ADC off,
LCD on (note 2),
R type, VLCD=VDD,
1/2 bias (RBIAS=400kW)
¾
12
18
mA
¾
18
24
mA
No load, WDT off, ADC off,
LCD on (note 2),
R type, VLCD=VDD,
1/3 bias (RBIAS=600kW)
¾
10
15
mA
¾
15
22
mA
IDD9
IDD10
IDD11
IDD12
IDD13
IDD14
IDD15
Rev. 1.40
Operating Current
(Slow Mode, fM=4MHz)
(Crystal OSC, RC OSC)
Operating Current
(Slow Mode, fM=4MHz)
(Crystal OSC, RC OSC)
Operating Current
(Slow Mode, fM=8MHz)
(Crystal OSC, RC OSC)
Operating Current
(Slow Mode, fM=8MHz)
(Crystal OSC, RC OSC)
Operating Current
(Slow Mode, fM=8MHz)
(Crystal OSC, RC OSC)
Operating Current
(fSYS=32768Hz (note 1)
or 32K_INT internal RC OSC)
Operating Current
(fSYS=32768Hz (note 1)
or 32K_INT internal RC OSC)
5V
3V
5V
3V
5V
3V
5V
3V
5V
3V
5V
3V
5V
3V
5V
3V
5V
No load, fSYS=fM=4MHz
ADC off
No load, fSYS=fSLOW=1MHz
ADC off
No load, fSYS=fSLOW=2MHz
ADC off
No load, fSYS=fSLOW=1MHz
ADC off
No load, fSYS=fSLOW=2MHz
ADC off
No load, fSYS=fSLOW=4MHz
ADC off
5
September 8, 2009
HT56R64
Symbol
IDD16
IDD17
Parameter
ISTB7
Unit
¾
6
9
mA
¾
9
13
mA
¾
5
8
mA
¾
8
12
mA
¾
0.1
1.0
mA
¾
0.2
2.0
mA
¾
1.5
3.0
mA
¾
2.5
5.0
mA
No load, system HALT,
WDT off, LCD on (note 2),
1/2 bias, C type, VLCD=VDD
¾
2
4
mA
¾
3
6
mA
No load, system HALT,
WDT off, LCD on (note 2),
1/3 bias, C type, VLCD=3V
¾
2
4
mA
¾
3
6
mA
No load, system HALT,
WDT off, LCD on (note 2),
R type, VLCD=VDD,
1/2 bias (RBIAS=400kW)
¾
10
15
mA
¾
15
22
mA
No load, system HALT,
WDT off, LCD on (note 2),
R type, VLCD=VDD,
1/3 bias (RBIAS=600kW)
¾
6
9
mA
¾
10
15
mA
No load, system HALT,
WDT off, LCD off,
SPI or I2C on, PCLK on,
PCLK=fSYS/8
¾
150
220
mA
¾
350
530
mA
3V
No load, WDT off, ADC off,
LCD on (note 2), C type
1/3 bias, VLCD=3V
Operating Current
(fSYS=32768Hz (note 1)
or 32K_INT internal RC OSC)
3V
ISTB2
ISTB6
Max.
Operating Current
(fSYS=32768Hz (note 1)
or 32K_INT internal RC OSC)
Standby Current ( Sleep)
(fSYS, fLCD=off;
fLCD, fWDT=fSUB=32768Hz (note
1) or 32K_INT RC OSC)
ISTB5
Typ.
Conditions
Standby Current ( Sleep)
(fSYS, fSUB, fS, fLCD, fWDT=off)
ISTB4
Min.
VDD
ISTB1
ISTB3
Test Conditions
5V
5V
3V
5V
3V
5V
Standby Current ( Idle)
(fSYS, fWDT=off; fS (note 3)=
fSUB=32768Hz (note 1)
or 32K_INT RC OSC)
3V
Standby Current ( Idle)
(fSYS, fWDT=off; fS (note 3)=
fSUB=32768Hz (note 1)
or 32K_INT RC OSC)
3V
Standby Current ( Idle)
(fSYS, fWDT=off; fS (note 3)=
fSUB=32768Hz (note 1)
or 32K_INT RC OSC)
Standby Current ( Idle)
(fSYS, fWDT=off; fS (note 3)=
fSUB=32768Hz (note 1)
or 32K_INT RC OSC)
Standby Current ( Idle)
(fSYS=on, fSYS=fM=4MHz,
fWDT, fLCD=off,
fS (note 3)=fSUB=32768Hz
(note 1) or 32K_INT RC OSC)
5V
5V
3V
5V
3V
5V
3V
5V
No load, LCD off, WDT off,
ADC off
No load, system HALT,
WD off
No load, system HALT,
WDT on
VIL1
Input Low Voltage for I/O Ports,
TMR and INT
¾
¾
0
¾
0.3VDD
V
VIH1
Input High Voltage for I/O Ports,
TMR and INT
¾
¾
0.7VDD
¾
VDD
V
VIL2
Input Low Voltage (RES)
¾
¾
0
¾
0.4VDD
V
VIH2
Input High Voltage (RES)
¾
¾
VLVR
VLVD
IOL1
Rev. 1.40
Low Voltage Reset Voltage
Low Voltage Detector Voltage
0.9VDD
¾
VDD
V
¾
Configuration option: 2.1V
1.98
2.10
2.22
V
¾
Configuration option: 3.15V
2.98
3.15
3.32
V
¾
Configuration option: 4.2V
3.98
4.20
4.42
V
¾
Configuration option: 2.2V
2.08
2.20
2.32
V
¾
Configuration option: 3.3V
3.12
3.30
3.50
V
¾
Configuration option: 4.4V
4.12
4.40
4.70
V
6
12
¾
mA
10
25
¾
mA
3V
I/O Port Sink Current
5V
VOL=0.1VDD
6
September 8, 2009
HT56R64
Symbol
Parameter
VDD
3V
IOH1
I/O Port Source Current
IOL2
LCD Common and Segment
Current
IOH2
LCD Common and Segment
Current
RPH
Pull-high Resistance for I/O
Ports
Note:
Test Conditions
5V
3V
5V
3V
5V
Conditions
VOH=0.9VDD
VOL=0.1VDD
VOH=0.9VDD
3V
¾
5V
Min.
Typ.
Max.
Unit
-2
-4
¾
mA
-5
-8
¾
mA
210
420
¾
mA
350
700
¾
mA
-80
-160
¾
mA
-180
-360
¾
mA
20
60
100
kW
10
30
50
kW
1. 32768Hz is in slow start mode (RTCC.4=1) for the D.C. current measurement.
2. LCD waveform is in Type A condition.
3. fS is the internal clock for Buzzer, RTC, Time base and WDT.
4. Both Timer/Event Counters are off. Timer filter is disabled for all test conditions.
A.C. Characteristics
Symbol
Parameter
Ta=25°C
Test Conditions
fSYS1
System Clock
(Crystal OSC, RC OSC)
fSYS2
System Clock
(RTC Crystal OSC)
¾
fRTCOSC
RTC Frequency
¾
Timer I/P Frequency
(TMR0/TMR1)
fTIMER
Min.
Typ.
Max.
Unit
2.2V~5.5V
32
¾
4000
kHz
3.0V~5.5V
32
¾
8000
kHz
4.5V~5.5V
32
¾
12000
kHz
2.2V~5.5V
¾
32768
¾
Hz
VDD
¾
¾
Conditions
¾
32768
¾
Hz
2.2V~5.5V
¾
0
¾
4000
kHz
3.3V~5.5V
0
¾
8000
kHz
4.5V~5.5V
0
¾
12000
kHz
28.8
32.0
35.2
kHz
fRC32K
32K RC Oscillator
¾
tRES
External Reset Low Pulse Width
¾
¾
1
¾
¾
ms
tLVR
Low Voltage Reset Time
¾
¾
0.1
0.4
0.6
ms
tLVDO
Time for LVDO Become Stable,
LVDC is Enabled
¾
¾
¾
¾
100
ms
tSST1
System Start-up Timer Period
¾
Power-on
¾
1024
¾
tSYS*
tSST2
System Start-up Timer Period for
XTAL or RTC Oscillator
¾
Wake-up from Power
Down Mode
¾
1024
¾
tSYS*
tSST3
System Start-up Timer Period for
External RC or External Clock
¾
Wake-up from Power
Down Mode
¾
1
2
tSYS*
tINT
Interrupt Pulse Width
¾
1
¾
¾
ms
Note:
2.2V~5.5V, After Trim
¾
*tSYS=1/fSYS1 or 1/fSYS2
Rev. 1.40
7
September 8, 2009
HT56R64
ADC Characteristics
Ta=25°C
Test Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
52QFP, 64LQFP
0
¾
AVDD
V
100QFP
0
¾
VREF
V
VDD
VAD
¾
A/D Input Voltage
Conditions
VREF
A/D Input Reference Voltage
Range
¾
AVDD=5V
1.6
¾
AVDD+0.1
V
DNL
A/C Differential Non-Linearity
¾
AVDD=5V, VREF=AVDD,
tAD=0.5ms
-2
¾
2
LSB
INL
ADC Integral Non-Linearity
¾
AVDD=5V, VREF=AVDD,
tAD=0.5ms
-4
¾
4
LSB
IADC
Additional Power Consumption
if A/D Converter is Used
3V
¾
0.50
0.75
mA
¾
1.00
1.50
mA
tAD
A/D Clock Period
¾
¾
0.5
¾
¾
ms
tADC
A/D Conversion Time
¾
¾
¾
16
¾
tAD
¾
5V
Power-on Reset Characteristics
Ta=25°C
Test Conditions
Symbol
Parameter
VDD
Conditions
Min.
Typ.
Max.
Unit
VPOR
VDD Start Voltage to Ensure
Power-on Reset
¾
¾
¾
¾
0
mV
RRVDD
VDD raising rate to Ensure
Power-on Reset
¾
¾
0.05
¾
¾
V/ms
tPOR
Minimum Time for VDD Stays at
VPOR to Ensure Power-on Reset
¾
¾
200
¾
¾
ms
V
D D
tP
O R
R R
V D D
V
P O R
T im e
Rev. 1.40
8
September 8, 2009
HT56R64
System Architecture
ternally generated non-overlapping clocks, T1~T4. The
Program Counter is incremented at the beginning of the
T1 clock during which time a new instruction is fetched.
The remaining T2~T4 clocks carry out the decoding and
execution functions. In this way, one T1~T4 clock cycle
forms one instruction cycle. Although the fetching and
execution of instructions takes place in consecutive instruction cycles, the pipelining structure of the
microcontroller ensures that instructions are effectively
executed in one instruction cycle. The exception to this
are instructions where the contents of the Program
Counter are changed, such as subroutine calls or
jumps, in which case the instruction will take one more
instruction cycle to execute.
A key factor in the high-performance features of the
Holtek range of microcontrollers is attributed to their internal system architecture. The range of devices take
advantage of the usual features found within RISC
microcontrollers providing increased speed of operation
and enhanced performance. The pipelining scheme is
implemented in such a way that instruction fetching and
instruction execution are overlapped, hence instructions
are effectively executed in one cycle, with the exception
of branch or call instructions. An 8-bit wide ALU is used
in practically all instruction set operations, which carries
out arithmetic operations, logic operations, rotation, increment, decrement, branch decisions, etc. The internal
data path is simplified by moving data through the Accumulator and the ALU. Certain internal registers are implemented in the Data Memory and can be directly or
indirectly addressed. The simple addressing methods of
these registers along with additional architectural features ensure that a minimum of external components is
required to provide a functional I/O and A/D control system with maximum reliability and flexibility. This makes
the device suitable for low-cost, high-volume production
for controller applications.
When the RC oscillator is used, OSC2 is free for use as
a T1 phase clock synchronizing pin. This T1 phase clock
has a frequency of fSYS/4 with a 1:3 high/low duty cycle.
For instructions involving branches, such as jump or call
instructions, two machine cycles are required to complete instruction execution. An extra cycle is required as
the program takes one cycle to first obtain the actual
jump or call address and then another cycle to actually
execute the branch. The requirement for this extra cycle
should be taken into account by programmers in timing
sensitive applications.
Clocking and Pipelining
The main system clock, derived from either a Crystal/Resonator or RC oscillator is subdivided into four in-
O s c illa to r C lo c k
( S y s te m C lo c k )
P h a s e C lo c k T 1
P h a s e C lo c k T 2
P h a s e C lo c k T 3
P h a s e C lo c k T 4
P ro g ra m
C o u n te r
P ip e lin in g
P C
P C + 1
F e tc h In s t. (P C )
E x e c u te In s t. (P C -1 )
P C + 2
F e tc h In s t. (P C + 1 )
E x e c u te In s t. (P C )
F e tc h In s t. (P C + 2 )
E x e c u te In s t. (P C + 1 )
System Clocking and Pipelining
M O V A ,[1 2 H ]
2
C A L L D E L A Y
3
C P L [1 2 H ]
4
:
5
:
6
1
D E L A Y :
F e tc h In s t. 1
E x e c u te In s t. 1
F e tc h In s t. 2
E x e c u te In s t. 2
F e tc h In s t. 3
F lu s h P ip e lin e
F e tc h In s t. 6
E x e c u te In s t. 6
F e tc h In s t. 7
N O P
Instruction Fetching
Rev. 1.40
9
September 8, 2009
HT56R64
Program Counter
The lower byte of the Program Counter, known as the
Program Counter Low register or PCL, is available for
program control and is a readable and writable register.
By transferring data directly into this register, a short program jump can be executed directly, however, as only
this low byte is available for manipulation, the jumps are
limited to the present page of memory, that is 256 locations. When such program jumps are executed it should
also be noted that a dummy cycle will be inserted.
During program execution, the Program Counter is used
to keep track of the address of the next instruction to be
executed. It is automatically incremented by one each
time an instruction is executed except for instructions,
such as ²JMP² or ²CALL² that demand a jump to a
non-consecutive Program Memory address. It must be
noted that only the lower 8 bits, known as the Program
Counter Low Register, are directly addressable.
The lower byte of the Program Counter is fully accessible under program control. Manipulating the PCL might
cause program branching, so an extra cycle is needed
to pre-fetch. Further information on the PCL register can
be found in the Special Function Register section.
When executing instructions requiring jumps to
non-consecutive addresses such as a jump instruction,
a subroutine call, interrupt or reset, etc., the
microcontroller manages program control by loading the
required address into the Program Counter. For conditional skip instructions, once the condition has been
met, the next instruction, which has already been
fetched during the present instruction execution, is discarded and a dummy cycle takes its place while the correct instruction is obtained.
Program Counter Bits
Mode
b11
b10
b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
0
External Interrupt 0
0
0
0
0
0
0
0
0
0
1
0
0
External Interrupt 1
0
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 0 Overflow
0
0
0
0
0
0
0
0
1
1
0
0
Timer/Event Counter 1 Overflow
0
0
0
0
0
0
0
1
0
0
0
0
SPI/I C Interrupt
0
0
0
0
0
0
0
1
0
1
0
0
Multi-Function Interrupt
0
0
0
0
0
0
0
1
1
0
0
0
2
Skip
Program Counter + 2
Loading PCL
PC11 PC10 PC9 PC8
Jump, Call Branch
Return from Subroutine
@7
@6
@5
@4
@3
@2
@1
@0
11
10
9
8
7
6
5
4
3
2
1
0
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note:
PC11~PC8: Current Program Counter bits
1 1~ 0: Instruction code address bits
Rev. 1.40
@7~@0: PCL bits
S11~S0: Stack register bits
10
September 8, 2009
HT56R64
· Increment and Decrement INCA, INC, DECA, DEC
Stack
· Branch decision, JMP, SZ, SZA, SNZ, SIZ, SDZ,
This is a special part of the memory which is used to
save the contents of the Program Counter only. The
stack has 12 levels and is neither part of the data nor
part of the program space, and is neither readable nor
writeable. The activated level is indexed by the Stack
Pointer, SP, and is neither readable nor writeable. At a
subroutine call or interrupt acknowledge signal, the contents of the Program Counter are pushed onto the stack.
At the end of a subroutine or an interrupt routine, signaled by a return instruction, RET or RETI, the Program
Counter is restored to its previous value from the stack.
After a device reset, the Stack Pointer will point to the
top of the stack.
P ro g ra m
T o p o f S ta c k
SIZA, SDZA, CALL, RET, RETI
Program Memory
The Program Memory is the location where the user
code or program is stored. For this device the Program
Memory is an OTP type, which means it can be programmed only one time. By using the appropriate programming tools, this OTP memory device offer users
the flexibility to conveniently debug and develop their
applications while also offering a means of field programming.
The program memory is used to store the program instructions, which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
4096´15 bits format which are addressed by the program counter and table pointer. The JMP and CALL instructions provide only 11 bits of address to allow
branching within any 4K program memory. When doing
a JMP or CALL instruction.
C o u n te r
S ta c k L e v e l 1
S ta c k L e v e l 2
S ta c k
P o in te r
B o tto m
S ta c k L e v e l 3
o f S ta c k
P ro g ra m
M e m o ry
S ta c k L e v e l 1 2
Structure
The Program Memory has a capacity of 4K by 15 bits.
The Program Memory is addressed by the Program
Counter and also contains data, table information and
interrupt entries. Table data, which can be setup in any
location within the Program Memory, is addressed by a
separate table pointer register.
If the stack is full and an enabled interrupt takes place,
the interrupt request flag will be recorded but the acknowledge signal will be inhibited. When the Stack
Pointer is decremented, by RET or RETI, the interrupt
will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily.
However, when the stack is full, a CALL subroutine instruction can still be executed which will result in a stack
overflow. Precautions should be taken to avoid such
cases which might cause unpredictable program
branching.
Special Vectors
Within the Program Memory, certain locations are reserved for special usage such as reset and interrupts.
· Location 000H
This vector is reserved for use by the device reset for
program initialisation. After a device reset is initiated, the
program will jump to this location and begin execution.
Arithmetic and Logic Unit - ALU
The arithmetic-logic unit or ALU is a critical area of the
microcontroller that carries out arithmetic and logic operations of the instruction set. Connected to the main
microcontroller data bus, the ALU receives related instruction codes and performs the required arithmetic or
logical operations after which the result will be placed in
the specified register. As these ALU calculation or operations may result in carry, borrow or other status
changes, the status register will be correspondingly updated to reflect these changes. The ALU supports the
following functions:
· Location 004H
This vector is used by the external interrupt 0. If the
external interrupt pin receives an active edge, the program will jump to this location and begin execution if
the external interrupt is enabled and the stack is not
full.
· Location 008H
This vector is used by the external interrupt 1. If the
external interrupt pin receives an active edge, the program will jump to this location and begin execution if
the external interrupt is enabled and the stack is not
full.
· Arithmetic operations: ADD, ADDM, ADC, ADCM,
SUB, SUBM, SBC, SBCM, DAA
· Location 00CH
· Logic operations: AND, OR, XOR, ANDM, ORM,
This internal vector is used by the Timer/Event Counter 0. If a Timer/Event Counter 0 overflow occurs, the
program will jump to this location and begin execution
if the timer/event counter interrupt is enabled and the
stack is not full.
XORM, CPL, CPLA
· Rotation RRA, RR, RRCA, RRC, RLA, RL, RLCA,
RLC
Rev. 1.40
11
September 8, 2009
HT56R64
· Location 010H
Look-up Table
This internal vector is used by the Timer/Event Counter 1. If a Timer/Event Counter 1 overflow occurs, the
program will jump to this location and begin execution
if the timer/event counter interrupt is enabled and the
stack is not full.
Any location within the Program Memory can be defined
as a look-up table where programmers can store fixed
data. To use the look-up table, the table pointer must
first be setup by placing the lower order address of the
look up data to be retrieved in the table pointer register,
TBLP. This register defines the lower 8-bit address of
the look-up table.
· Location 014H
This internal vector is used by the SPI/I2C interrupt.
When either an SPI or I2C bus, dependent upon which
one is selected, requires data transfer, the program
will jump to this location and begin execution if the
SPI/I2C interrupt is enabled and the stack is not full.
After setting up the table pointer, the table data can be
retrieved from the current Program Memory page or last
Program Memory page using the ²TABRDC[m]² or
²TABRDL [m]² instructions, respectively. When these instructions are executed, the lower order table byte from
the Program Memory will be transferred to the user defined Data Memory register [m] as specified in the instruction. The higher order table data byte from the
Program Memory will be transferred to the TBLH special
register. Any unused bits in this transferred higher order
byte will be read as ²0².
· Location 018H
This internal vector is used by the Multi-function Interrupt. When the Time Base overflows, the Real Time
Clock overflows, the A/D converter completes its conversion process, or an active edge appears on the External Peripheral interrupt pin, the program will jump to
this location and begin execution if the relevant interrupt is enabled and the stack is not full.
0 0 0 H
0 0 4 H
0 0 8 H
0 0 C H
0 1 0 H
0 1 4 H
0 1 8 H
In itia lis a tio n
V e c to r
The following diagram illustrates the addressing/data
flow of the look-up table:
E x te rn a l IN T 0
In te rru p t V e c to r
P ro g ra m C o u n te r
H ig h B y te
E x te rn a l IN T 1
In te rru p t V e c to r
P ro g ra m
M e m o ry
T B L P
T im e r C o u n te r 0
In te rru p t V e c to r
T im e r C o u n te r 1
In te rru p t V e c to r
T B L H
S p e c ifie d b y [m ]
T a b le C o n te n ts L o w
T a b le C o n te n ts H ig h B y te
B y te
S P I/I2C
In te rru p t V e c to r
M u lti_ F u n c tio n
In te rru p t V e c to r
F F F H
1 5 b its
N o t Im p le m e n te d
Program Memory Structure
Table Location Bits
Instruction
b11
b10
b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
TABRDC [m]
PC11
PC10
PC9
PC8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note:
PC11~PC8: Current program counter bits
Rev. 1.40
@7~@0: Table Pointer TBLP bits
12
September 8, 2009
HT56R64
Table Program Example
Because the TBLH register is a read-only register and
cannot be restored, care should be taken to ensure its
protection if both the main routine and Interrupt Service
Routine use table read instructions. If using the table
read instructions, the Interrupt Service Routines may
change the value of the TBLH and subsequently cause
errors if used again by the main routine. As a rule it is
recommended that simultaneous use of the table read
instructions should be avoided. However, in situations
where simultaneous use cannot be avoided, the interrupts should be disabled prior to the execution of any
main routine table-read instructions. Note that all table
related instructions require two instruction cycles to
complete their operation.
The following example shows how the table pointer and
table data is defined and retrieved from the
microcontroller. This example uses raw table data located in the last page which is stored there using the
ORG statement. The value at this ORG statement is
²700H² which refers to the start address of the last page
within the 2K Program Memory of the device. The table
pointer is setup here to have an initial value of ²06H².
This will ensure that the first data read from the data table will be at the Program Memory address ²706H² or 6
locations after the start of the last page. Note that the
value for the table pointer is referenced to the first address of the present page if the ²TABRDC [m]² instruction is being used. The high byte of the table data which
in this case is equal to zero will be transferred to the
TBLH register automatically when the ²TABRDL [m]² instruction is executed.
Tempreg1
tempreg2
:
:
mov
mov
db
db
?
?
; temporary register #1
; temporary register #2
a,06h
; initialise table pointer - note that this address
; is referenced
tblp,a
; to the last page or present page
tempreg1
;
;
;
;
:
:
tabrdl
dec tblp
tabrdl
:
:
org 700h
dc
transfers value in table referenced by table pointer
to tempregl
data at prog. memory address ²706H² transferred to
tempreg1 and TBLH
; reduce value of table pointer by one
tempreg2
;
;
;
;
;
;
transfers value in table referenced by table pointer
to tempreg2
data at prog.memory address ²705H² transferred to
tempreg2 and TBLH
in this example the data ²1AH² is transferred to
tempreg1 and data ²0FH² to register tempreg2
; sets initial address of last page
00Ah, 00Bh, 00Ch, 00Dh, 00Eh, 00Fh, 01Ah, 01Bh
:
:
Rev. 1.40
13
September 8, 2009
HT56R64
Data Memory
General Purpose Data Memory
The Data Memory is a volatile area of 8-bit wide RAM
internal memory and is the location where temporary information is stored. Divided into three sections, the first
of these is an area of RAM where special function registers are located. These registers have fixed locations
and are necessary for correct operation of the device.
Many of these registers can be read from and written to
directly under program control, however, some remain
protected from user manipulation. The second area of
Data Memory is reserved for general purpose use. All
locations within this area are read and write accessible
under program control. The third area is reserved for the
All microcontroller programs require an area of
read/write memory where temporary data can be stored
and retrieved for use later. It is this area of RAM memory
that is known as General Purpose Data Memory. This
area of Data Memory is fully accessible by the user program for both read and write operations. By using the
²SET [m].i² and ²CLR [m].i² instructions individual bits
can be set or reset under program control giving the
user a large range of flexibility for bit manipulation in the
Data Memory.
Special Purpose Data Memory
0 0 H
S p e c ia l P u r p o s e
D a ta M e m o ry
This area of Data Memory is where registers, necessary
for the correct operation of the microcontroller, are
stored. Most of the registers are both read and write type
but some are protected and are read only, the details of
which are located under the relevant Special Function
Register section. Note that for locations that are unused,
any read instruction to these addresses will return the
value ²00H².
B a n k 1
L C D
M e m o ry
3 F H
4 0 H
4 0 H
6 0 H
G e n e ra l P u rp o s e
D a ta M e m o ry
F F H
B a n k 0
B a n k 1
0 0 H
0 1 H
0 2 H
0 3 H
0 4 H
0 5 H
0 6 H
0 7 H
0 8 H
0 9 H
0 A H
0 B H
0 C H
0 D H
0 E H
0 F H
1 0 H
1 1 H
1 2 H
1 3 H
1 4 H
1 5 H
1 6 H
1 7 H
1 8 H
1 9 H
1 A H
1 B H
1 C H
1 D H
1 E H
1 F H
Bank 0 RAM Data Memory Structure
Note:
Most of the Data Memory bits can be directly
manipulated using the ²SET [m].i² and ²CLR
[m].i² with the exception of a few dedicated bits.
The Data Memory can also be accessed
through the memory pointer registers MP0 and
MP1.
LCD Memory. This special area of Data Memory is
mapped directly to the LCD display so data written into
this memory area will directly affect the displayed data.
The addresses of the LCD Memory area overlap those
in the General Purpose Data Memory area, switching
between the two areas is achieved by setting the Bank
Pointer to the correct value.
Structure
The Data Memory is subdivided into 2 banks, known as
Bank 0 and Bank 1, all of which are implemented in 8-bit
wide RAM. RAM Data Memory located in Bank 0 is subdivided into two sections, the Special Purpose Data
Memory and the General Purpose Data Memory. The
start address of the RAM Data Memory for all devices is
the address ²00H². The last Data Memory address is
²FFH².
IA
M
IA
M
R 0
P 0
R 1
P 1
B P
A C C
P C L
T B L P
T B L H
R T C C
S T A T U S
IN T C 0
T M R 0
T M R 0 C
T M R 1 H
T M R 1 L
T M R 1 C
P A
P A C
P B
P B C
P
P
P
P
P D
P D C
W M 0 L
W M 0 H
W M 1 L
W M 1 H
IN T C 1
2 0 H
2 1 H
2 2 H
2 3 H
2 4 H
2 5 H
2 6 H
2 7 H
2 8 H
2 9 H
2 A H
2 B H
2 C H
2 D H
2 E H
2 F H
3 0 H
3 1 H
3 2 H
3 3 H
3 4 H
3 5 H
3 6 H
3 7 H
3 8 H
3 9 H
3 A H
3 B H
3 C H
3 D H
3 E H
3 F H
P W
P W
P W
P W
A D
A D
A D
A C
C L K
P A
P A
P B
M 2
M 2
M 3
M 3
R L
R H
C R
S R
M O
W U
P U
P U
L
H
H
L
D
P D P U
IN T E D G E
L C D C
L C D O
L C D O
M IS
M F
S IM
S IM
S
S IM A R
T R L
U T 1
U T 2
C
IC
C O N 0
C O N 1
IM D R
/S IM C O N 2
: U n u s e d R e a d a s "0 0 "
Special Purpose RAM Data Memory
Bank 1 is for LCD display memory which occupy 128´8
location.
Rev. 1.40
14
September 8, 2009
HT56R64
LCD Memory
Indirect Addressing Registers - IAR0, IAR1
The data to be displayed on the LCD is also stored in an
area of fully accessible Data Memory. By writing to this
area of RAM, the LCD display output can be directly
controlled by the application program. As the LCD Memory exists in Bank 1, but have addresses which map into
the General Purpose Data Memory, it is necessary to
first ensure that the Bank Pointer is set to the value 01H
before accessing the LCD Memory. The LCD Memory
can only be accessed indirectly using the Memory
Pointer MP1 and the indirect addressing register IAR1.
When the Bank Pointer is set to Bank 1 to access the
LCD Data Memory, if any addresses with a value less
than 40H are read, the Special Purpose Memory in
Bank 0 will be accessed. Also, if the Bank Pointer is set
to Bank 1, if any addresses higher than the last address
in Bank 1 are read, then a value of 00H will be returned.
The Indirect Addressing Registers, IAR0 and IAR1, although having their locations in normal RAM register
space, do not actually physically exist as normal registers. The method of indirect addressing for RAM data
manipulation uses these Indirect Addressing Registers
and Memory Pointers, in contrast to direct memory addressing, where the actual memory address is specified. Actions on the IAR0 and IAR1 registers will result in
no actual read or write operation to these registers but
rather to the memory location specified by their corresponding Memory Pointer, MP0 or MP1. Acting as a
pair, IAR0 and MP0 can together access data Bank 0
while the IAR1 and MP1 register pair can access data
from Bank 0 and Bank 1. As the Indirect Addressing
Registers are not physically implemented, reading the
Indirect Addressing Registers indirectly will return a result of ²00H² and writing to the registers indirectly will result in no operation.
Special Function Registers
To ensure successful operation of the microcontroller,
certain internal registers are implemented in the Data
Memory area. These registers ensure correct operation
of internal functions such as timers, interrupts, etc., as
well as external functions such as I/O data control and
A/D converter operation. The location of these registers
within the Data Memory begins at the address 00H. Any
unused Data Memory locations between these special
function registers and the point where the General Purpose Memory begins is reserved for future expansion
purposes, attempting to read data from these locations
will return a value of 00H.
Memory Pointers - MP0, MP1
For all devices, two Memory Pointers, known as MP0
and MP1 are provided. These Memory Pointers are
physically implemented in the Data Memory and can be
manipulated in the same way as normal registers providing a convenient way with which to address and track
data. When any operation to the relevant Indirect Addressing Registers is carried out, the actual address that
the microcontroller is directed to, is the address specified by the related Memory Pointer. MP0, together with
Indirect Addressing Register, IAR0, are used to access
data from Bank 0, while MP1 and IAR1 are used to access data from Bank 0 and Bank 1.
The following example shows how to clear a section of four RAM locations already defined as locations adres1 to
adres4.
data .section ¢data¢
adres1
db ?
adres2
db ?
Adres3
db ?
adres4
db ?
block
db ?
code .section at 0 ¢code¢
org 00h
start:
mov
mov
mov
mov
a,04h
block,a
a,offset adres1
mp0,a
; setup size of block
loop:
clr
inc
sdz
jmp
IAR0
mp0
block
loop
; clear the data at address defined by MP0
; increment memory pointer
; check if last memory location has been cleared
; Accumulator loaded with first RAM address
; setup memory pointer with first RAM address
continue:
The important point to note here is that in the example shown above, no reference is made to specific RAM addresses.
Rev. 1.40
15
September 8, 2009
HT56R64
Bank Pointer - BP
Program Counter Low Register - PCL
The Data Memory is divided into 2 Banks, known as
Bank 0 and Bank 1. Selecting the required Data Memory
area is achieved using the Bank Pointer. If data in Bank
0 is to be accessed, then the BP register must be loaded
with the value 00H, while if data in Bank 1 is to be accessed, then the BP register must be loaded with the
value 01H.
To provide additional program control functions, the low
byte of the Program Counter is made accessible to programmers by locating it within the Special Purpose area
of the Data Memory. By manipulating this register, direct
jumps to other program locations are easily implemented. Loading a value directly into this PCL register
will cause a jump to the specified Program Memory location, however, as the register is only 8-bit wide, only
jumps within the current Program Memory page are permitted. When such operations are used, note that a
dummy cycle will be inserted.
The Data Memory is initialised to Bank 0 after a reset,
except for the WDT time-out reset in the Power Down
Mode, in which case, the Data Memory bank remains
unaffected. It should be noted that the Special Function
Data Memory is not affected by the bank selection,
which means that the Special Function Registers can be
accessed from within either Bank 0 or Bank 1. Directly
addressing the Data Memory will always result in Bank 0
being accessed irrespective of the value of the Bank
Pointer.
Look-up Table Registers - TBLP, TBLH
These two special function registers are used to control
operation of the look-up table which is stored in the Program Memory. TBLP is the table pointer and indicates
the location where the table data is located. Its value
must be setup before any table read commands are executed. Its value can be changed, for example using the
²INC² or ²DEC² instructions, allowing for easy table data
pointing and reading. TBLH is the location where the
high order byte of the table data is stored after a table
read data instruction has been executed. Note that the
lower order table data byte is transferred to a user defined location.
Accumulator - ACC
The Accumulator is central to the operation of any
microcontroller and is closely related with operations
carried out by the ALU. The Accumulator is the place
where all intermediate results from the ALU are stored.
Without the Accumulator it would be necessary to write
the result of each calculation or logical operation such
as addition, subtraction, shift, etc., to the Data Memory
resulting in higher programming and timing overheads.
Data transfer operations usually involve the temporary
storage function of the Accumulator; for example, when
transferring data between one user defined register and
another, it is necessary to do this by passing the data
through the Accumulator as no direct transfer between
two registers is permitted.
Status Register - STATUS
This 8-bit register contains the zero flag (Z), carry flag
(C), auxiliary carry flag (AC), overflow flag (OV), power
down flag (PDF), and watchdog time-out flag (TO).
These arithmetic/logical operation and system management flags are used to record the status and operation of
the microcontroller.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
b 7
b 0
B P 0
B P R e g is te r
B P 0
0
1
D a ta M e m o ry
B a n k 0
B a n k 1
N o t im p le m e n te d , w r ite " 0 " o n ly
Bank Pointer
b 7
b 0
T O
P D F
O V
Z
A C
C
S T A T U S R e g is te r
A r
C a
A u
Z e
ith m e
r r y fla
x ilia r y
r o fla g
O v e r flo w
g
tic /L o g ic O p e r a tio n F la g s
c a r r y fla g
fla g
S y s te m M
P o w e r d o w
W a tc h d o g
N o t im p le m
a n
n
tim
e
a g e m e n t F la g s
fla g
e - o u t fla g
n te d , re a d a s "0 "
Status Register
Rev. 1.40
16
September 8, 2009
HT56R64
registers TMR0 and TMR1L/TMR1H are the locations
where the timer values are located. These register can
also be preloaded with fixed data to allow different time
intervals to be setup. Two associated control registers,
TMR0C and TMR1C, contains the setup information for
these timers, which determines in what mode the timer is
to be used as well as containing the timer on/off control
function.
other registers. Any data written into the status register
will not change the TO or PDF flag. In addition, operations related to the status register may give different results due to the different instruction operations. The TO
flag can be affected only by a system power-up, a WDT
time-out or by executing the ²CLR WDT² or ²HALT² instruction. The PDF flag is affected only by executing the
²HALT² or ²CLR WDT² instruction or during a system
power-up.
Input/Output Ports and Control Registers
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
Within the area of Special Function Registers, the I/O
registers and their associated control registers play a
prominent role. All I/O ports have a designated register
correspondingly labeled as PA, PB and PD. These labeled I/O registers are mapped to specific addresses
within the Data Memory as shown in the Data Memory
table, which are used to transfer the appropriate output
or input data on that port. With each I/O port there is an
associated control register labeled PAC, PBC and PDC,
also mapped to specific addresses with the Data Memory. The control register specifies which pins of that port
are set as inputs and which are set as outputs. To setup
a pin as an input, the corresponding bit of the control
register must be set high, for an output it must be set
low. During program initialization, it is important to first
setup the control registers to specify which pins are outputs and which are inputs before reading data from or
writing data to the I/O ports. One flexible feature of these
registers is the ability to directly program single bits using the ²SET [m].i² and ²CLR [m].i² instructions. The
ability to change I/O pins from output to input and vice
versa by manipulating specific bits of the I/O control registers during normal program operation is a useful feature of these devices.
· C is set if an operation results in a carry during an ad-
dition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C
is also affected by a rotate through carry instruction.
· AC is set if an operation results in a carry out of the
low nibbles in addition, or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is
cleared.
· Z is set if the result of an arithmetic or logical operation
is zero; otherwise Z is cleared.
· OV is set if an operation results in a carry into the high-
est-order bit but not a carry out of the highest-order bit,
or vice versa; otherwise OV is cleared.
· PDF is cleared by a system power-up or executing the
²CLR WDT² instruction. PDF is set by executing the
²HALT² instruction.
· TO is cleared by a system power-up or executing the
²CLR WDT² or ²HALT² instruction. TO is set by a
WDT time-out.
In addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be
pushed onto the stack automatically. If the contents of
the status registers are important and if the subroutine
can corrupt the status register, precautions must be
taken to correctly save it.
Pulse Width Modulator Registers
The device contains four Pulse Width Modulator function
with their own related independent control register,
known as PWM0L, PWM0H, PWM1L, PWM1H, PWM2L,
PWM2H, PWM3L and PWM3H. The 12-bit contents of
each register pair, defines the duty cycle value for the
modulation cycle of the Pulse Width Modulator.
Interrupt Control Register INTC0, INTC1, MFIC, INTEDGE
These 8-bit registers, control the operation of the device
interrupt functions. By setting various bits within these
registers using standard bit manipulation instructions, the
enable/disable function of each interrupt can be independently controlled. A master interrupt bit within this register, the EMI bit, acts like a global enable/disable and is
used to set all of the interrupt enable bits on or off. This bit
is cleared when an interrupt routine is entered to disable
further interrupt and is set by executing the ²RETI² instruction. The INTEDGE register is used to select the active edges for the two external interrupt pins INT0 and
INT1.
A/D Converter Registers ADRL, ADRH, ADCR, ACSR
The device contains an 8-channel 12-bit A/D converter.
The correct operation of the A/D requires the use of two
data registers and two control registers. The two data
registers, a high byte data register known as ADRH, and
a low byte data register known as ADRL, are the register
locations where the digital value is placed after the completion of an analog to digital conversion cycle. Functions such as the A/D enable/disable, A/D channel
selection and A/D clock frequency are determined using
the two control registers, ADCR and ACSR.
Timer/Event Counter Registers TMR0, TMR1L/ TMR1H, TMR0C, TMR1C
The device contains one internal 8-bit Timer/Event
Counter and one 16-bit Timer/Event Counter. The
Rev. 1.40
17
September 8, 2009
HT56R64
Serial Interface Registers
non-latching, which means the inputs must be ready at
the T2 rising edge of instruction ²MOV A,[m]², where m
denotes the port address. For output operation, all the
data is latched and remains unchanged until the output
latch is rewritten.
The device contains two serial interfaces, an SPI and an
I 2 C interface. The SIMCON0, SIMCON1, SIMAR/
SIMCON2 are the control registers for the Serial Interface function while the SIMDR is the data register for the
Serial Interface Data.
Pull-high Resistors
Port A Wake-up Register - PAWU
Many product applications require pull-high resistors for
their switch inputs usually requiring the use of an external resistor. To eliminate the need for these external resistors, all I/O pins, when configured as an input have
the capability of being connected to an internal pull-high
resistor. These pull-high resistors are selected using
registers PAPU, PBPU and PDPU and are implemented
using weak PMOS transistors.
All pins on Port A have a wake-up function enable a low
going edge on these pins to wake-up the device when it
is in a power down mode. The pins on Port A that are
used to have a wake-up function are selected using this
resister.
Pull-High Resistors - PAPU, PBPU, PDPU
All I/O pins on Ports PA, PB and PD, if setup as inputs,
can be connected to an internal pull-high resistor. The
pins which require a pull-high resistor to be connected
are selected using these registers.
Port A Wake-up
The HALT instruction forces the microcontroller into a
Power Down condition which preserves power, a feature that is important for battery and other low-power applications. Various methods exist to wake-up the
microcontroller, one of which is to change the logic condition on one of the Port A pins from high to low. After a
HALT instruction forces the microcontroller into entering
a Power Down condition, the processor will remain in a
low-power state until the logic condition of the selected
wake-up pin on Port A changes from high to low. This
function is especially suitable for applications that can
be woken up via external switches. Each pin on Port A
can be selected individually to have this wake-up feature using the PAWU register.
Register - CLKMOD
The device operates using a dual clock system whose
mode is controlled using this register. The register controls functions such as the clock source, the idle mode
enable and the division ratio for the slow clock.
LCD Registers - LCDCTRL, LCDOUT1, LCDOUT2
The device contains a fully integrated LCD Driver function which can be setup in various configurations allowing it to control a wide range of external LCD panels.
Most of these options are controlled using the
LCDCTRL register. As some of the LCD segment driving pins can also be setup to be used as CMOS oututs,
two registers, LCDOUT1 and LCDOUT2, are used to
select the required function.
Port A Open Drain Function
All I/O pins in the device have CMOS structures, however Port A pins PA0~PA3 can also be setup as open
drain structures. This is implemented using the
ODE0~ODE3 bits in the MISC register.
Miscellaneous Register - MISC
I/O Port Control Registers
The miscellaneous register is used to control two functions. The four lower bits are used for the Watchdog
Timer control, while the highest four bits are used to select open drain outputs for pins PA0~PA3.
Each I/O port has its own control register known as PAC,
PBC, and PDC, to control the input/output configuration.
With this control register, each CMOS output or input
with or without pull-high resistor structures can be reconfigured dynamically under software control. Each pin
of the I/O ports is directly mapped to a bit in its associated port control register. For the I/O pin to function as
an input, the corresponding bit of the control register
must be written as a ²1². This will then allow the logic
state of the input pin to be directly read by instructions.
When the corresponding bit of the control register is
written as a ²0², the I/O pin will be setup as a CMOS output. If the pin is currently setup as an output, instructions
can still be used to read the output register. However, it
should be noted that the program will in fact only read
the status of the output data latch and not the actual
logic status of the output pin.
Input/Output Ports
Holtek microcontrollers offer considerable flexibility on
their I/O ports. With the input or output designation of every pin fully under user program control, pull-high selections for all ports and wake-up selections on certain
pins, the user is provided with an I/O structure to meet
the needs of a wide range of application possibilities.
The device provides 24 bidirectional input/output lines
labeled with port names PA, PB and PD. These I/O ports
are mapped to the RAM Data Memory with specific addresses as shown in the Special Purpose Data Memory
table. All of these I/O ports can be used for input and
output operations. For input operation, these ports are
Rev. 1.40
18
September 8, 2009
HT56R64
b 7
O D E 3
O D E 2
O D E 1
O D E 0
W D T E N 3
W D T E N 2
W D T E N 1
b 0
W D T E N 0
M IS C
R e g is te r
W a tc h d o g T im e r E n a b le C o n tr o l
- d e s c r ib e d e ls e w h e r e
P A 0 O p e n D r a in C o n tr o l
1 : e n a b le
0 : d is a b le
P A 1 O p e n D r a in C o n tr o l
1 : e n a b le
0 : d is a b le
P A 2 O p e n D r a in C o n tr o l
1 : e n a b le
0 : d is a b le
P A 3 O p e n D r a in C o n tr o l
1 : e n a b le
0 : d is a b le
PA0~PA3 Open Drain Control - MISC
output to enable the PWM output. If the PDC port control register has setup the pin as an input, then the pin
will function as a normal logic input with the usual
pull-high selection, even if the PWM registers have
been selected.
Pin-shared Functions
The flexibility of the microcontroller range is greatly enhanced by the use of pins that have more than one function. Limited numbers of pins can force serious design
constraints on designers but by supplying pins with
multi-functions, many of these difficulties can be overcome. For some pins, the chosen function of the
multi-function I/O pins is set by configuration options
while for others the function is set by application program control.
· A/D Inputs
The device has eight A/D converter inputs. All of these
analog inputs are pin-shared with I/O pins on Port B. If
these pins are to be used as A/D inputs and not as normal I/O pins then the corresponding bits in the A/D
Converter Control Register, ADCR, must be properly
set. There are no configuration options associated with
the A/D function. If used as I/O pins, then full pull-high
resistor register remain, however if used as A/D inputs
then any pull-high resistor selections associated with
these pins will be automatically disconnected.
· External Interrupt Inputs
The external interrupt pins INT0, INT1 are pin-shared
with the I/O pins PD4, PD5. For applications not requiring an external interrupt input, the pin-shared external interrupt pin can be used as a normal I/O pin,
however to do this, the external interrupt enable bits in
the INTC0 register must be disabled.
I/O Pin Structures
The accompanying diagrams illustrate the I/O pin internal structures. As the exact logical construction of the
I/O pin may differ from these drawings, they are supplied
as a guide only to assist with the functional understanding of the I/O pins.
· External Timer Clock Input
The external timer pins TMR0, TMR1 are pin-shared
with the I/O pin PD6, PD7. To configure it to operate as
a timer input, the corresponding control bits in the timer
control register must be correctly set and the pin must
also be setup as an input. Note that the original I/O
function will remain even if the pin is setup to be used
as an external timer input.
Programming Considerations
Within the user program, one of the first things to consider is port initialisation. After a reset, all of the I/O data
and port control registers will be set high. This means
that all I/O pins will default to an input state, the level of
which depends on the other connected circuitry and
whether pull-high selections have been chosen. If the
port control registers, PAC, PBC and PDC, are then programmed to setup some pins as outputs, these output
pins will have an initial high output value unless the associated port data registers, PA, PB and PD, are first
programmed. Selecting which pins are inputs and which
are outputs can be achieved byte-wide by loading the
correct values into the appropriate port control register
or by programming individual bits in the port control register using the ²SET [m].i² and ²CLR [m].i² instructions.
Note that when using these bit control instructions, a
· PFD Output
The device contains a PFD function whose single output is pin-shared with PA3. The output function of this
pin is chosen via a configuration option and remains
fixed after the device is programmed. Note that the
corresponding bit of the port control register, PAC.3,
must setup the pin as an output to enable the PFD output. If the PAC port control register has setup the pin
as an input, then the pin will function as a normal logic
input with the usual pull-high selection, even if the
PFD configuration option has been selected.
· PWM Outputs
The device contains four PWM outputs shared with
pin PD0~PD3. The PWM output functions are chosen
via registers. Note that the corresponding bit of the
port control register, PDC, must setup the pin as an
Rev. 1.40
19
September 8, 2009
HT56R64
read-modify-write operation takes place. The
microcontroller must first read in the data on the entire
port, modify it to the required new bit values and then rewrite this data back to the output ports.
T 1
S y s te m
T 2
T 3
T 1
T 4
T 2
T 3
Port A has the additional capability of providing wake-up
functions. When the device is in the Power Down Mode,
various methods are available to wake the device up.
One of these is a high to low transition of any of the Port
A pins. Single or multiple pins on Port A can be setup to
have this function.
T 4
C lo c k
P o rt D a ta
W r ite to P o r t
R e a d fro m
P o rt
Read/Write Timing
P A 0 ~ P A 3 O p e n D r a in S e le c t
D a ta B u s
W r ite C o n tr o l R e g is te r
P u ll- H ig h
R e g is te r
S e le c t
C o n tr o l B it
Q
D
V
D D
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
D a ta B it
Q
D
W r ite D a ta R e g is te r
C K
S
Q
M
P A 0 /P A 1 /P A 3 /P D 0 /P D 1 /P D 2 /P D 3
B Z /B Z /P F D /P W M 0 /P W M 1 /P W M 2 /P W M 3
M
R e a d D a ta R e g is te r
S y s te m
IN T
IN T
T M R
T M R
0 fo
1 fo
0 fo
1 fo
U
4 o n
5 o n
6 o n
7 o n
/B Z
/B Z
/P F D
/T M R
/T M R
, P A 7
/P W M
/IN T 0
/IN T 1
/T M R
/T M R
2
3
0 ~ P D 3 /P W M 3
0
1
X
B Z E N , P F D E N ,
P W M E N
X
W a k e -u p
r P D
r P D
r P D
r P D
U
P A 0
P A 1
P A 2
P A 3
P A 4
P A 5
P A 6
P D 0
P D 4
P D 5
P D 6
P D 7
W a k e - u p o p tio n
ly
ly
ly
ly
PA, PD Input/Output Ports
b 7
P x P U 7
P x P U 1
b 0
P x P U 0
P A P U , P B P U , P D P U R e g is te r
P A .0 , P B .0 , P D .0 P u ll- h ig h
1 : e n a b le
0 : d is a b le
P A .1 , P B .1 , P D .1 P u ll- h ig h
1 : e n a b le
0 : d is a b le
P A .7 , P B .7 , P D .7 P u ll- h ig h
1 : e n a b le
0 : d is a b le
Pull-High Resistor Register - PAPU, PBPU, PDPU
Rev. 1.40
20
September 8, 2009
HT56R64
V
D a ta B u s
W r ite C o n tr o l R e g is te r
D D
P u ll- H ig h
R e g is te r
S e le c t
C o n tr o l B it
Q
D
W e a k
P u ll- u p
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
W r ite D a ta R e g is te r
P B 0 /A N 0 ~ P B 7 /A N 7
D a ta B it
Q
D
C K
S
Q
M
R e a d D a ta R e g is te r
P C R 2
P C R 1
P C R 0
T o A /D
U
X
A n a lo g
In p u t
S e le c to r
C o n v e rte r
A C S 2 ~ A C S 0
PB Input/Output Ports
Liquid Crystal Display (LCD) Driver
The LCD Data Memory is stored in Bank 1. The Data
Memory Bank is chosen by using the Bank Pointer,
which is a special function register in the Data Memory,
with the name, BP. When the lowest bit of the Bank
Pointer has the binary value ²0², only the General Purpose Data Memory will be accessed, no read or write
actions to the LCD Memory will take place. To access
the LCD Memory therefore requires first that Bank 1 is
selected by setting the lowest bit of the Bank Pointer to
the binary value ²1². After this, the LCD Memory can
then be accessed by using indirect addressing through
the use of Memory Pointer MP1. With Bank 1 selected,
then using MP1 to read or write to the memory area,
40H~60H, will result in operations to the LCD Memory.
Directly addressing the LCD Memory is not applicable
and will result in a data access to the Bank 0 General
Purpose Data Memory.
For large volume applications, which incorporate an
LCD in their design, the use of a custom display rather
than a more expensive character based display reduces
costs significantly. However, the corresponding signals
required, which vary in both amplitude and time, to drive
such a custom display require many special considerations for proper LCD operation to occur. The Holtek
LCD Driver function, with its internal LCD signal generating circuitry and various options, will automatically
generate these time and amplitude varying signals to
provide a means of direct driving and easy interfacing to
a range of custom LCDs.
LCD Memory
An area of Data Memory is especially reserved for use
by the LCD data. This data area is known as the LCD
Memory. Any data written here will be automatically
read by the internal LCD driver circuits, which will in turn
automatically generate the necessary LCD driving signals. Therefore any data written into the LCD Memory
will be immediately reflected into the actual LCD display
connected to the microcontroller. The start address of
the LCD Memory is 40H; the end address of the LCD
Memory is 60H.
The diagrams below are based on 33´2, 33´3 or 32´4
format pixel drive capability LCD panels. The 4-COM format will be automatically setup when the 1/4 duty control
bit is selected while the 3-COM format will be automatically setup if the 1/3 duty control bit is selected.
As the LCD Data Memory addresses overlap those of
the General Purpose Data Memory, the LCD Data Memory is stored in its own memory data bank, which is different from that of the General Purpose Data Memory.
Rev. 1.40
21
September 8, 2009
HT56R64
b 7
b 6
b 5
b 4
b 3
b 2
b 1
b 0
b 7
b 6
b 5
b 4
b 3
b 2
b 1
b 0
4 0 H
S E G
0
4 0 H
S E G
4 1 H
S E G
1
4 1 H
S E G
0
1
: U n u s e d
R e a d a s "0 "
5 F H
S E G
3 1
5 F H
S E G
3 1
6 0 H
S E G
3 2
6 0 H
S E G
3 2
C O M
C O M
1
2
3
C O M
C O M
1
2
0
C O M
C O M
C O M
0
(1 /2 o r 1 /3 D u ty )
(1 /4 D u ty )
LCD Memory Map
LCD Registers
LCD will always be disabled. Bits RSEL0 and RSEL1
select the internal bias resistors to supply the LCD panel
with the correct bias voltages. A choice to best match
the LCD panel used in the application can be selected
also to minimise bias current. The TYPE bit is used to
select whether Type A or Type B LCD control signals
are used.
A single LCD Control Register in the Data Memory,
known as LCDCTRL, is used to control the various
setup features of the LCD Driver. Various bits in this register control functions such as duty type, bias type, bias
resistor selection as well as overall LCD enable and disable. The LCDEN bit in the LCDCTRL register will only
be effective when the device is in the Normal, Slow or
Idle Mode. If the device is in the Sleep Mode then the
b 7
T Y P E
L C D E N B
R E L C D
(R e s e t L C D )
S le e p M o d e
b 0
D T Y C 1 D T Y C 0
B IA S
R S E L 1
R S E L 0
L C D E N
L C D C T R L R e g is te r
L C D e
1 : e n a
0 : d is a
In th e
L C D w
In th e
n a b le
b le
b le
N o rm
ill b e
S le e p
L C D b ia s r e
R S E L 1 R
0
0
1
1
/d is a b le c o n tr o l
a l, S lo w o r Id le m o d e
o n /o ff a c c o r d in g to " L C D E N " = 1 /0
m o d e th e L C D is a lw a y s o ff
s is to r s e
S E L 0
0
6
1
3
0
1
1
5
le
V
0
0
0
0
c t
= 4
re
W re
W re
re s
L C D 1
0 k
0 k
0 k
k W
W
.5 V
s is to
s is to
s is to
is to r
r (1 /3
r (1 /3
r (1 /3
(1 /3 B
B ia
B ia
B ia
ia s
s ) , I B IA S
s ) , I B IA S
s ) , I B IA S
) , I B IA S =
= 7 .5 u A
= 1 5 u A
= 4 5 u A
9 0 u A
L C D B ia s
1 : 1 /3 B ia s
0 : 1 /2 B ia s
N o t im p le m e n te d , r e a d a s " 0 "
L C D D u ty
D T Y C 1
0
0
1
1
D T Y C 0
0
1
1
1
0
1
1
r
/2 d u
/3 d u
/4 d u
e s e rv
ty
ty
ty
e d
L C D T y p e A o r B
1 : T y p e B
0 : T y p e A
LCD Control Register - LCDCTRL
Rev. 1.40
22
September 8, 2009
HT56R64
b 7
L C D O 8
b 0
L C D O 0
L C D O U T 1 R e g is te r
S E G 0 ~ S E G 7 s e g m e n t o r C M O S o u tp u t
1 : C M O S o u tp u t
0 : S E G o u tp u t
S E G 8 ~ S E G 1 5 s e g m e n t o r C M O S o u tp u t
1 : C M O S o u tp u t
0 : S E G o u tp u t
N o t im p le m e n te d , r e a d a s " 0 "
LCD Output Control Register - LCDOUT1
b 7
L C D O 2 3
L C D O 2 2
L C D O 2 1
L C D O 2 0
L C D O 1 9
L C D O 1 8
L C D O 1 7
b 0
L C D O 1 6
L C D O U T 2 R e g is te r
S E G 1 6 ~ S E G 2 3 s e g m e n t o r C M O S o u tp u t
1 : C M O S o u tp u t
0 : S E G o u tp u t
LCD Output Control Register - LCDOUT2
LCD Driver Output
Two registers, LCDOUT1 and LCDOUT2 are used to
determine if the output function of LCD pins SEG0~
SEG23 are used a LCD segment drivers or CMOS outputs. If used as CMOS outputs then the LCD Data Memory is used to determine the logic level of the CMOS
output pins. Note that as only two bits are used to determine the output function of the SEG0~SEG7 and
SEG8~SEG15 pins, individual pins from these two
groups of pins cannot be chosen to have either a segment or CMOS output function. The output function of
pins SEG16~SEG23 can be chosen individually to be
either an LCD segment driver or a CMOS input.
The number of COM and SEG outputs supplied by the
LCD driver, as well as its biasing and duty selections,
are dependent upon the LCD control bits selected. The
accompanying table lists the various selections. The
Bias Type, whether C or R type is selected using a configuration option.
LDC Reset Function
The LCD has an internal reset function that is an OR
function of the inverted LCDEN bit in the LCDCTRL register and the Sleep function. The LCD reset signal is active high. The LCDENB signal is the inverse of the
LCDEN bit in the LCDCTRL register.
The LCD clock source is the internal clock signal, fSUB,
divided by 8, using an internal divider circuit. The fSUB
internal clock is supplied by either the internal 32K_INT
oscillator or the external RTC oscillator, the choice of
which is determined by a configuration option. For
proper LCD operation, this arrangement is provided to
generate an ideal LCD clock source frequency of 4kHz.
LCD Clock Frequency
External RTC Osc.
4KHz
LCD Clock Source
Rev. 1.40
33´2
1/3
33´3
1/4
32´4
Bias
Type
Waveform
Type
1/2 or
1/3
C or R
type
A or B
The nature of Liquid Crystal Displays require that only
AC voltages can be applied to their pixels as the application of DC voltages to LCD pixels may cause permanent
damage. For this reason the relative contrast of an LCD
display is controlled by the actual RMS voltage applied
to each pixel, which is equal to the RMS value of the
voltage on the COM pin minus the voltage applied to the
SEG pin. This differential RMS voltage must be greater
than the LCD saturation voltage for the pixel to be on
and less than the threshold voltage for the pixel to be off.
The requirement to limit the DC voltage to zero and to
control as many pixels as possible with a minimum number of connections, requires that both a time and amplitude signal is generated and applied to the application
LCD. These time and amplitude varying signals are automatically generated by the LCD driver circuits in the
LCD Clock
4KHz
1/2
Bias
If the C-type of bias is used then an internal charge
pump will be enabled. This charge pump has two voltage multiplier options selected using a configuration option. Note that the C-type bias is not available on the
52-pin QFP package type.
LEDSEL=0 & LCDEN=1 must be enabled to activate the
LCDCTRL register function.
fSUB Clock Source
Driver
Number
LCD Selections
RELCD= (Sleep and IDLEN=0 ) or LCDENB.
Internal 32K_INT Osc.
Duty
23
September 8, 2009
HT56R64
microcontroller. What is known as the duty determines
the number of common lines used, which are also
known as backplanes or COMs. The duty, which is chosen by a control bit to have a value of 1/2, 1/3 or 1/4 and
which equates to a COM number of 2, 3 and 4 respectively, therefore defines the number of time divisions
within each LCD signal frame. Two types of signal generation are also provided, known as Type A and Type B,
the required type is selected via the TYPE bit in the
LCDCTRL register. Type B offers lower frequency signals, however lower frequencies may introduce flickering and influence display clarity. The accompanying
timing diagrams depict the LCD signals generated by
the microcontroller for various values of duty and bias.
For R type biasing an external LCD voltage source must
be supplied on pin VLCD1 to generate the internal biasing voltages. This could be the microcontroller power
supply or some other voltage source. For the R type 1/2
bias selection, three voltage levels VSS, VA and VB are
utilised. The voltage VA is equal to the externally supplied voltage source applied to pin VLCD1. VB is generated internally by the microcontroller and will have a
value equal to VLCD1/2. For the R type 1/3 bias selection, four voltage levels VSS, VA, VB and VC are utilised. The voltage VA is equal to VLCD1, VB is equal to
VLCD1´2/3 while VC is equal to VLCD1´1/3. In addition
to selecting 1/2 or 1/3 bias, several values of bias resistor can be chosen using bits in the LCDCTRL register.
Different values of internal bias resistors can be selected using the RSEL0 and RESEL1 bits in the
LCDCTRL register. This along with the voltage on pin
VLCD1 will determine the bias current. The connection
to the VMAX pin depends upon the voltage that is applied to VLCD1. If the VDD voltage is greater than the
voltage applied to the VLCD1 pin then the VMAX pin
should be connected to VDD, otherwise the VMAX pin
should be connected to pin VLCD1. Note that no external capacitors or resistors are required to be connected
if R type biasing is used.
LCD Voltage Source and Biasing
The time and amplitude varying signals generated by
the LCD Driver function require the generation of several voltage levels for their operation. The number of
voltage levels used by the signal depends upon the
value of the BIAS bit in the LCDCTRL register. The device can have either R type or C type biasing selected
via a configuration option. Selecting the C type biasing
will enable an internal charge pump whose multiplying
ration can be selected using an additional configuration
option.
V M A X
V L C D 1
V
A
V L C D 1
L C D
P o w e r S u p p ly
C 1
(= V L C D 1 ´ 1 .5 )
V
V M A X
0 .1 m F
V
V 1
0 .1 m F
B
(= V L C D 1 ´ 0 .5 )
V L C D 2
(= V L C D 1 ´ 0 .5
V C u s e d fo r
1 /3 B ia s o n ly )
0 .1 m F
C 2
C h a rg e
P u m p
V 1
C
C
A
(= V L C D 1 )
0 .1 m F
V
C 1
V
C 2
C h a rg e
P u m p
B
(= V L C D 1 )
L C D
P o w e r S u p p ly
V L C D 2
0 .1 m F
0 .1 m F
ty p e 1 /3 B ia s p
C
´ 3 C h a r g e P u m
ty p e 1 /2 B ia s p
´ 2 C h a r g e P u m
C Type Bias Voltage Levels
V
A
(= V L C D 1 )
V
L C D
P o w e r S u p p ly
V
A
(= V L C D 1 )
L C D
P o w e r S u p p ly
R
B
R
V
V 1
C
(= V L C D 1 ´ 1 /3 )
L C D
V M A X
V L C D 1
R
(= V L C D 1 ´ 2 /3 )
V
V M A X
V L C D 1
R
B
(= V L C D 1 ´ 1 /2 )
0 .1 m F
R
O n /O ff
L C D
V 1
0 .1 m F
O n /O ff
R Type Bias Voltage Levels
Rev. 1.40
24
September 8, 2009
HT56R64
Condition
device types. On these package types, pins C1, C2 and
VLCD2 are not provided. It is recommended that a
0.1mF capacitor is connected between the V1 pin and
ground on the 52-pin QFP package types.
VMAX connection
VDD > VLCD1
Connect VMAX to VDD
Otherwise
Connect VMAX to VLCD1
R Type Bias Current VMAX Connection
It is extremely important to ensure that these charge
pump generated internal voltages do not exceed the
maximum VDD voltage of 5.5V. Note that the C-type bias
type is not available on the 52-pin QFP package type.
For C type biasing an external LCD voltage source must
also be supplied on pin VLCD1 to generate the internal
biasing voltages. The C type biasing scheme uses an internal charge pump circuit, which in the case of the 1/3
bias selection can generate voltages higher than what is
supplied on VLCD1. This feature is useful in applications where the microcontroller supply voltage is less
than the supply voltage required by the LCD. The external LCD power supply should be connected to pin
VLCD1 and a filter capacitor connected to pin VLCD2.
An additional charge pump capacitor must also be connected between pins C1 and C2 to generate the necessary voltage levels.
Biasing Type
VMAX Connection
1/3
Bias
VDD>VLCD1´1.5 Connect VMAX to VDD
Otherwise
Connect VMAX to V1
1/2
Bias
VDD>VLCD1
Connect VMAX to VDD
Otherwise
Connect VMAX to VLCD1
C Type Biasing VMAX Connection
Programming Considerations
For the C type 1/2 bias selection, three voltage levels
VSS, VA and VB are utilised. The voltage VA is generated
internally and has a value of VLCD1. VB will have a value
equal to VA´0.5. For the C type 1/2 bias configuration VC
is not used.
Certain precautions must be taken when programming
the LCD. One of these is to ensure that the LCD memory
is properly initialised after the microcontroller is powered on. Like the General Purpose Data Memory, the
contents of the LCD memory are in an unknown condition after power-on. As the contents of the LCD memory
will be mapped into the actual LCD, it is important to initialise this memory area into a known condition soon after applying power to obtain a proper display pattern.
For the C type 1/3 bias selection, four voltage levels
VSS, VA, VB and VC are utilised. The voltage VA is generated internally and has a value of VLCD1´1.5. VB will
have a value equal to VA ´ 2/3 and VC will have a value
equal to VA ´ 1/3. The connection to the VMAX pin depends upon the bias and the voltage that is applied to
VLCD1, the details are shown in the table. Note that C
type biasing is not available on the 52-pin QFP package
Consideration must also be given to the capacitive load
of the actual LCD used in the application. As the load
presented to the microcontroller by LCD pixels can be
generally modeled as mainly capacitive in nature, it is
D u r in g R e s e t o r in H A L T M o d e
V A
V B
C O M 0 , C O M 1
V S S
V A
V B
V S S
A ll s e g m e n t o u tp u ts
1 F ra m e
N o r m a l O p e r a tio n M o d e
V A
C O M 0
V B
V S S
V A
V B
V S S
V A
V B
V S S
C O M 1
A ll s e g m e n ts O F F
V A
V B
C O M 0 s e g m e n ts O N
V S S
V A
C O M 1 s e g m e n ts O N
V B
V S S
V A
V B
V S S
A ll s e g m e n ts O N
LCD Driver Output - Type A - 1/2 Duty, 1/2 Bias
Note
For 1/2 Bias, VA=VLCD1, VB=VLCD1´1/2 for both R and C type.
Rev. 1.40
25
September 8, 2009
HT56R64
important that this is not excessive, a point that is particularly true in the case of the COM lines which may be
connected to many LCD pixels. The accompanying diagram depicts the equivalent circuit of the LCD.
One additional consideration that must be taken into account is what happens when the microcontroller enters
a HALT condition. The ²LCDEN² control bit in the
LCDCTRL register permits the LCD to be powered off to
reduce power consumption. If ²LCDEN²=0 is selected,
the driving signals to the LCD will cease, producing a
blank display pattern but reducing any power consumption associated with the LCD.
With such a frequency chosen, the microcontroller internal LCD driver circuits will ensure that the appropriate
LCD driving signals are generated to obtain a suitable
LCD frame frequency.
S E G 0
S E G 1
S E G 2
After Power-on, note that as the LCDEN bit in the
LCDCTRL register will be cleared to zero, the LCD function will be disabled.
S E G n
C O M 0
The following timing diagrams depict the LCD signals
generated by the microcontroller for various values of
duty and bias.
C O M 1
C O M 2
C O M 3
LCD Panel Equivalent Circuit
D u r in g R e s e t o r in H A L T M o d e
V A
V B
C O M 0 , C O M 1 , C O M 2
V S S
V A
V B
V S S
A ll s e g m e n t o u tp u ts
N o r m a l O p e r a tio n M o d e
1 F ra m e
V A
V B
C O M 0
V S S
V A
C O M 1
V B
V S S
V A
V B
V S S
V A
V B
V S S
V A
V B
V S S
C O M 2
A ll s e g m e n ts O F F
C O M 0 s e g m e n ts O N
V A
V B
C O M 1 s e g m e n ts O N
V S S
V A
C O M 2 s e g m e n ts O N
V B
V S S
V A
V B
V S S
C O M 0 , 1 s e g m e n ts O N
V A
C O M 0 , 2 s e g m e n ts O N
V B
V S S
V A
C O M 1 , 2 s e g m e n ts O N
V B
V S S
V A
A ll s e g m e n ts O N
V B
V S S
LCD Driver Output - Type A- 1/3 Duty, 1/2 Bias
Note:
For 1/2 Bias, the VA=VLCD1, VB=VLCD1´1/2 for both R and C type.
Rev. 1.40
26
September 8, 2009
HT56R64
D u r in g R e s e t o r in H A L T M o d e
V A
V B
C O M 0 , C O M 1 , C O M 2 , C O M 3
V C
A ll s e g m e n t o u tp u ts
1 F ra m e
N o r m a l O p e r a tio n M o d e
V S S
V A
V B
V C
V S S
V A
V B
C O M 0
V C
V S S
V A
V B
C O M 1
V C
V S S
V A
V B
V C
V S S
C O M 2
V A
V B
C O M 3
V C
V S S
V A
V B
A ll s e g m e n ts O F F
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
C O M 0 s e g m e n ts O N
C O M 1 s e g m e n ts O N
V A
V B
C O M 2 s e g m e n ts O N
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
C O M 3 s e g m e n ts O N
C O M 0 , 1 s e g m e n ts O N
C O M 0 , 2 s e g m e n ts O N
C O M 0 , 3 s e g m e n ts O N
( o th e r c o m b in a tio n s a r e o m itte d )
V A
V B
A ll s e g m e n ts O N
V C
V S S
LCD Driver Output - Type A - 1/4 Duty, 1/3 Bias
Note:
For 1/3 R type bias, the VA=VLCD1, VB=VLCD1´2/3 and VC=VLCD1´1/3.
For 1/3 C type bias, the VA=VLCD1´1.5, VB=VLCD1 and VC=VLCD1´1/2.
Rev. 1.40
27
September 8, 2009
HT56R64
D u r in g R e s e t o r in H A L T M o d e
V A
V B
C O M 0 , C O M 1 , C O M 2
V C
A ll s e g m e n t o u tp u ts
1 F ra m e
N o r m a l O p e r a tio n M o d e
V S S
V A
V B
V C
V S S
V A
V B
C O M 0
V C
V S S
V A
V B
C O M 1
V C
V S S
V A
V B
V C
V S S
C O M 2
V A
V B
A ll s e g m e n ts O F F
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
C O M 0 s e g m e n ts O N
C O M 1 s e g m e n ts O N
V A
V B
C O M 2 s e g m e n ts O N
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
V A
V B
V C
V S S
C O M 0 , 1 s e g m e n ts O N
C O M 0 , 2 s e g m e n ts O N
C O M 1 , 2 s e g m e n ts O N
A ll s e g m e n ts O N
LCD Driver Output - Type A - 1/3 Duty, 1/3 Bias
Note:
For 1/3 R type bias, the VA=VLCD1, VB=VLCD1´2/3 and VC=VLCD1´1/3.
For 1/3 C type bias, the VA=VLCD1´1.5, VB=VLCD1 and VC=VLCD1´1/2.
Rev. 1.40
28
September 8, 2009
HT56R64
V A
V B
C O M 0
V S S
V A
V B
C O M 1
V S S
V A
C O M 0
S e g m e n ts O n
V B
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
V S S
V A
C O M 1
S e g m e n ts O n
V B
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
O ff
O n
V S S
V A
C O M 0
S e g m e n ts O ff
V B
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
O ff
V S S
LCD Driver Output - Type B - 1/2 Duty, 1/2 Bias
Note:
For 1/2 bias, the VA=VLCD, VB=VLCD1´1/2 for both R and C type.
Rev. 1.40
29
September 8, 2009
HT56R64
Timer/Event Counters
of the T0E or T1E bit, each high to low, or low to high
transition on the external timer pin will increment the
counter by one.
The provision of timers form an important part of any
microcontroller, giving the designer a means of carrying
out time related functions. The devices contain one 8-bit
and one 16-bit count-up timer. As each timer has three
different operating modes, they can be configured to operate as a general timer, an external event counter or as
a pulse width measurement device. The provision of a
prescaler to the clock circuitry of the 8-bit Timer/Event
Counter also gives added range to this timer.
Timer Registers - TMR0, TMR1L, TMR1H
The timer registers are special function registers located in
the Special Purpose Data Memory and is the place where
the actual timer value is stored. For the 8-bit Timer/Event
Counter 0, this register is known as TMR0. For 16-bit
Timer/Event Counter 1, the timer registers are known as
TMR1L and TMR1H. The value in the timer registers increases by one each time an internal clock pulse is received or an external transition occurs on the external
timer pin. The timer will count from the initial value loaded
by the preload register to the full count of FFH for the 8-bit
timer or FFFFH for the 16-bit timer at which point the timer
overflows and an internal interrupt signal is generated.
The timer value will then be reset with the initial preload
register value and continue counting.
There are two types of registers related to the
Timer/Event Counters. The first are the registers that
contain the actual value of the Timer/Event Counter and
into which an initial value can be preloaded. Reading
from these registers retrieves the contents of the
Timer/Event Counter. The second type of associated
register is the Timer Control Register which defines the
timer options and determines how the Timer/Event
Counter is to be used. The Timer/Event Counters can
have the their clock configured to come from an internal
clock source. In addition, their clock source can also be
configured to come from an external timer pin.
To achieve a maximum full range count of FFH for the
8-bit timer or FFFFH for the 16-bit timer, the preload registers must first be cleared to all zeros. It should be
noted that after power-on, the preload register will be in
an unknown condition. Note that if the Timer/Event
Counter is switched off and data is written to its preload
registers, this data will be immediately written into the
actual timer registers. However, if the Timer/Event
Counter is enabled and counting, any new data written
into the preload data registers during this period will remain in the preload registers and will only be written into
the timer registers the next time an overflow occurs.
Configuring the Timer/Event Counter Input Clock
Source
The internal timer¢s clock can originate from various
sources. The system clock source is used when the
Timer/Event Counter is in the timer mode or in the pulse
width measurement mode. For Timer/Event Counter 0
this internal clock source is fSYS which is also divided by
a prescaler, the division ratio of which is conditioned by
the Timer Control Register, TMR0C, bits T0PSC0~
T0PSC2. For Timer/Event Counter 1 this internal clock
source can be chosen from a combination of internal
clocks using a configuration option and the T1S bit in the
TMR1C register.
For the 16-bit Timer/Event Counter which has both low
byte and high byte timer registers, accessing these registers is carried out in a specific way. It must be noted
when using instructions to preload data into the low byte
timer register, namely TMR1L, the data will only be
placed in a low byte buffer and not directly into the low
byte timer register. The actual transfer of the data into
An external clock source is used when the timer is in the
event counting mode, the clock source being provided
on an external timer pin TMR0 or TMR1, depending
upon which timer is used. Depending upon the condition
P r e s c a le r O u tp u t
In c re m e n t
T im e r C o n tr o lle r
T im e r + 1
T im e r + 2
T im e r + N
T im e r + N + 1
Timer Mode Timing Chart
E x te rn a l E v e n t
In c re m e n t
T im e r C o u n te r
T im e r + 1
T im e r + 2
T im e r + 3
Event Counter Mode Timing Chart
Rev. 1.40
30
September 8, 2009
HT56R64
the low byte timer register is only carried out when a
write to its associated high byte timer register, namely
TMR1H, is executed. On the other hand, using instructions to preload data into the high byte timer register will
result in the data being directly written to the high byte
timer register. At the same time the data in the low byte
buffer will be transferred into its associated low byte
timer register. For this reason, the low byte timer register should be written first when preloading data into the
16-bit timer registers. It must also be noted that to read
the contents of the low byte timer register, a read to the
high byte timer register must be executed first to latch
the contents of the low byte timer register into its associated low byte buffer. After this has been done, the low
byte timer register can be read in the normal way. Note
that reading the low byte timer register will result in reading the previously latched contents of the low byte buffer
and not the actual contents of the low byte timer register.
It is the Timer Control Register together with its corresponding timer registers that control the full operation of
the Timer/Event Counters. Before the timers can be
used, it is essential that the appropriate Timer Control
Register is fully programmed with the right data to ensure its correct operation, a process that is normally carried out during program initialisation.
To choose which of the three modes the timer is to operate in, either in the timer mode, the event counting mode
or the pulse width measurement mode, bits 7 and 6 of
the Timer Control Register, which are known as the bit
pair T0M1/T0M0 or T1M1/T1M0 respectively, depending upon which timer is used, must be set to the required
logic levels. The timer-on bit, which is bit 4 of the Timer
Control Register and known as T0ON or T1ON, depending upon which timer is used, provides the basic on/off
control of the respective timer. Setting the bit high allows
the counter to run, clearing the bit stops the counter. For
timers that have prescalers, bits 0~2 of the Timer Control Register determine the division ratio of the input
clock prescaler. The prescaler bit settings have no effect
if an external clock source is used. If the timer is in the
event count or pulse width measurement mode, the active transition edge level type is selected by the logic
Timer Control Registers - TMR0C, TMR1C
The flexible features of the Holtek microcontroller
Timer/Event Counters enable them to operate in three
different modes, the options of which are determined by
the contents of their respective control register.
D a ta B u s
R e lo a d
P r e lo a d R e g is te r
T 0 P S C 2 ~ T 0 P S C 0
(1 /1 ~ 1 /1 2 8 )
fS
7 - s ta g e P r e s c a le r
Y S
T 0 M 1
T 0 M 0
F ilte r
T M R 0
F ilte r O n /O ff
C o n fig u r a tio n o p tio n
T im e r /E v e n t
C o u n te r
T im e r /E v e n t C o u n te r
M o d e C o n tro l
T 0 O N
O v e r flo w
to In te rru p t
8 - B it T im e r /E v e n t C o u n te r
¸ 2
P F D 0
T 0 E
Timer/Event Counter 0 Structure
D a ta B u s
L o w B y te
B u ffe r
E x te rn a l fR
M
T C
In te rn a l 3 2 K -IN T
U
X
C o n fig u r a tio n
O p tio n
fS
Y S
fS
U B
M
/4
U
X
T 1 M 1
T im e r /E v e n t C o u n te r
M o d e C o n tro l
T 1 S
F ilte r O n /O ff
C o n fig u r a tio n o p tio n
H ig h B y te
T 1 O N
F ilte r
T M R 1
1 6 - B it
P r e lo a d R e g is te r
T 1 M 0
L o w
R e lo a d
O v e r flo w
to In te rru p t
B y te
1 6 - B it T im e r /E v e n t C o u n te r
¸ 2
P F D 1
T 1 E
Timer/Event Counter 1 Structure
M
P F D 0
P F D 1
U
X
P F D
C o n fig u r a tio n
O p tio n
Rev. 1.40
31
September 8, 2009
HT56R64
b 0
b 7
T 0 M 1 T 0 M 0
T 0 O N
T 0 E
T 0 P S C 2
T 0 P S C 1
T 0 P S C 0
T im e r /E v e n t C o u n te r C o n tr o l R e g is te r
T M R 0 C
T im e r p r e s c a le r r a te s e le
T 0 P
T 0 P S C 2 T 0 P S C 1
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
E v e n t C
1 : c o u n
0 : c o u n
P u ls e W
1 : s ta rt
0 : s ta rt
o u n te r a c tiv e e d g
t o n fa llin g e d g e
t o n r is in g e d g e
id th M e a s u r e m e n
c o u n tin g o n r is in g
c o u n tin g o n fa llin g
0
c t
S C 0
1
0
1
0
1
0
1
T im e r
1 :1
1 :2
1 :4
1 :8
1 :1
1 :3
1 :6
1 :1
R a te
6
2
4
2 8
e s e le c t
t a c tiv e e d g e s e le c t
e d g e , s to p o n fa llin g e d g e
e d g e , s to p o n r is in g e d g e
T im e r /E v e n t C o u n te r c o u n tin g e n a b le
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d , r e a d a s " 0 "
O p e r a tin g m o d e
T 0 M 1 T 0 M 0
n o
0
0
e v
1
0
tim
0
1
p u
1
1
s e le c t
m o d
e n t c
e r m
ls e w
e a v a ila b le
o u n te r m o d e
o d e
id th m e a s u r e m e n t m o d e
Timer/Event Counter Control Register TMR0C
b 7
T 1 M 1
b 0
T 1 M 0
T 1 S
T 1 O N
T 1 E
T im e r /E v e n t C o u n te r C o n tr o l R e g is te r
T M R 1 C
N o t im p le m e n te d , r e a d a s " 0 "
E v
1 :
0 :
P u
1 :
0 :
e n t C
c o u n
c o u n
ls e W
s ta rt
s ta rt
o u n
t o n
t o n
id th
c o u n
c o u n
te r a c tiv e e d g
fa llin g e d g e
r is in g e d g e
M e a s u re m e n
tin g o n r is in g
tin g o n fa llin g
e s e le c t
t a c tiv e e d g e s e le c t
e d g e , s to p o n fa llin g e d g e
e d g e , s to p o n r is in g e d g e
T im e r /E v e n t C o u n te r c o u n tin g e n a b le
1 : e n a b le
0 : d is a b le
T im e r c lo c k s o u r c e
1 : fS U B (R T C o r 3 2 K R C )
0 : fS Y S /4
O p e r a tin g m o d e
T 1 M 1 T 1 M 0
n o
0
0
e v
0
1
1
tim
0
1
1
p u
s e le c t
m o d
e n t c
e r m
ls e w
e a v a ila b le
o u n te r m o d e
o d e
id th m e a s u r e m e n t m o d e
Timer/Event Counter 1 Control Register TMR1C
Rev. 1.40
32
September 8, 2009
HT56R64
level of bit 3 of the Timer Control Register which is
known as T0E or T1E depending upon which timer is
used. An additional T1S bit in the TMR1C register is
used to determine the clock source for Timer/Event
Counter 1.
Control Register Operating Mode
Select Bits for the Event Counter Mode
Bit7 Bit6
0
1
In this mode, the external timer pin, TMR0 or TMR1, is
used as the Timer/Event Counter clock source, however
it is not divided by the internal prescaler. After the other
bits in the Timer Control Register have been setup, the
enable bit T0ON or T1ON, which is bit 4 of the Timer
Control Register, can be set high to enable the
Timer/Event Counter to run. If the Active Edge Select bit
T0E or T1E, which is bit 3 of the Timer Control Register,
is low, the Timer/Event Counter will increment each time
the external timer pin receives a low to high transition. If
the Active Edge Select bit is high, the counter will increment each time the external timer pin receives a high to
low transition. When it is full and overflows, an interrupt
signal is generated and the Timer/Event Counter will reload the value already loaded into the preload register
and continue counting. The interrupt can be disabled by
ensuring that the Timer/Event Counter Interrupt Enable
bit in the Interrupt Control Register, INTC0, is reset to
zero.
Configuring the Timer Mode
In this mode, the Timer/Event Counter can be utilised to
measure fixed time intervals, providing an internal interrupt signal each time the Timer/Event Counter overflows. To operate in this mode, the Operating Mode
Select bit pair, T0M1/T0M0 or T1M1/T1M0, in the Timer
Control Register must be set to the correct value as
shown.
Bit7 Bit6
Control Register Operating Mode
Select Bits for the Timer Mode
1
0
In this mode the internal clock, fSYS , is used as the internal clock for 8-bit Timer/Event Counter 0 and fSUB or
fSYS/4 is used as the internal clock for 16-bit Timer/Event
Counter 1. However, the clock source, fSYS, for 8-bit
timer is further divided by a prescaler, the value of which
is determined by the Prescaler Rate Select bits
T0PSC2~T0PSC0, which are bits 2~0 in the Timer Control Register. After the other bits in the Timer Control
Register have been setup, the enable bit T0ON or
T1ON, which is bit 4 of the Timer Control Register, can
be set high to enable the Timer/Event Counter to run.
Each time an internal clock cycle occurs, the
Timer/Event Counter increments by one. When it is full
and overflows, an interrupt signal is generated and the
Timer/Event Counter will reload the value already
loaded into the preload register and continue counting.
The interrupt can be disabled by ensuring that the
Timer/Event Counter Interrupt Enable bit in the Interrupt
Control Register, INTC0, is reset to zero.
As the external timer pin is shared with an I/O pin, to ensure that the pin is configured to operate as an event
counter input pin, two things have to happen. The first is
to ensure that the Operating Mode Select bits in the
Timer Control Register place the Timer/Event Counter in
the Event Counting Mode, the second is to ensure that
the port control register configures the pin as an input. It
should be noted that in the event counting mode, even if
the microcontroller is in the Power Down Mode, the
Timer/Event Counter will continue to record externally
changing logic events on the timer input pin. As a result
when the timer overflows it will generate a timer interrupt
and corresponding wake-up source.
Configuring the Event Counter Mode
In this mode, a number of externally changing logic
events, occurring on the external timer pin, can be recorded by the Timer/Event Counter. To operate in this
mode, the Operating Mode Select bit pair, T0M1/T0M0
or T1M1/T1M0, in the Timer Control Register must be
set to the correct value as shown.
E x te rn a l T M R
P in In p u t
T 0 O N , T 1 O N , T 2 O N o r T 3 O N
( w ith T 0 E , T 1 E , T 2 E , T 3 E = 0 )
P r e s c a le r O u tp u t
In c re m e n t
T im e r C o u n te r
+ 1
T im e r
+ 2
+ 3
+ 4
P r e s c a le r O u tp u t is s a m p le d a t e v e r y fa llin g e d g e o f T 1 .
Pulse Width Measure Mode Timing Chart
Rev. 1.40
33
September 8, 2009
HT56R64
Configuring the Pulse Width Measurement Mode
the length of the pulse received on the external timer
pin. As the enable bit has now been reset, any further
transitions on the external timer pin will be ignored. Not
until the enable bit is again set high by the program can
the timer begin further pulse width measurements. In
this way, single shot pulse measurements can be easily
Made.
In this mode, the Timer/Event Counter can be utilised to
measure the width of external pulses applied to the external timer pin. To operate in this mode, the Operating
Mode Select bit pair, T0M1/T0M0 or T1M1/T1M0, in the
Timer Control Register must be set to the correct value
as shown.
Control Register Operating Mode
Select Bits for the Pulse Width
Measurement Mode
It should be noted that in this mode the Timer/Event
Counter is controlled by logical transitions on the external timer pin and not by the logic level. When the
Timer/Event Counter is full and overflows, an interrupt
signal is generated and the Timer/Event Counter will reload the value already loaded into the preload register
and continue counting. The interrupt can be disabled by
ensuring that the Timer/Event Counter Interrupt Enable
bit in the Interrupt Control Register, INTC, is reset to
zero.
Bit7 Bit6
1
1
In this mode the internal clock, fSYS , is used as the internal clock for 8-bit Timer/Event Counter 0 and fSUB or
fSYS/4 is used as the internal clock for 16-bit Timer/Event
Counter 1. However, the clock source, fSYS, for 8-bit
timer is further divided by a prescaler, the value of which
is determined by the Prescaler Rate Select bits
T0PSC2~T0PSC0, which are bits 2~0 in the Timer Control Register. After the other bits in the Timer Control
Register have been setup, the enable bit T0ON or
T1ON, which is bit 4 of the Timer Control Register, can
be set high to enable the Timer/Event Counter, however
it will not actually start counting until an active edge is received on the external timer pin.
As the external timer pin is shared with an I/O pin, to ensure that the pin is configured to operate as a pulse
width measurement pin, two things have to happen. The
first is to ensure that the Operating Mode Select bits in
the Timer Control Register place the Timer/Event Counter in the Pulse Width Measurement Mode, the second
is to ensure that the port control register configures the
pin as an input.
If the Active Edge Select bit T0E or T1E, which is bit 3 of
the Timer Control Register, is low, once a high to low
transition has been received on the external timer pin,
TMR0 or TMR1, the Timer/Event Counter will start
counting until the external timer pin returns to its original
high level. At this point the enable bit will be automatically reset to zero and the Timer/Event Counter will stop
counting. If the Active Edge Select bit is high, the
Timer/Event Counter will begin counting once a low to
high transition has been received on the external timer
pin and stop counting when the external timer pin returns to its original low level. As before, the enable bit
will be automatically reset to zero and the Timer/Event
Counter will stop counting. It is important to note that in
the Pulse Width Measurement Mode, the enable bit is
automatically reset to zero when the external control
signal on the external timer pin returns to its original
level, whereas in the other two modes the enable bit can
only be reset to zero under program control.
Programmable Frequency Divider - PFD
The Programmable Frequency Divider provides a
means of producing a variable frequency output suitable
for applications requiring a precise frequency generator.
The PFD output is pin-shared with the I/O pin PA3. The
PFD function is selected via configuration option, however, if not selected, the pin can operate as a normal I/O
pin.
The clock source for the PFD circuit can originate from
either the timer 0 or timer 1 overflow signal selected via
configuration option. The output frequency is controlled
by loading the required values into the timer registers
and prescaler registers to give the required division ratio. The timer will begin to count-up from this preload
register value until full, at which point an overflow signal
is generated, causing the PFD output to change state.
The timer will then be automatically reloaded with the
preload register value and continue counting-up.
The residual value in the Timer/Event Counter, which
can now be read by the program, therefore represents
T im e r O v e r flo w
P F D
C lo c k
P A 3 D a ta
P F D
O u tp u t a t P A 3
PFD Output Control
Rev. 1.40
34
September 8, 2009
HT56R64
For the PFD output to function, it is essential that the corresponding bit of the Port A control register PAC bit 3 is setup
as an output. If setup as an input the PFD output will not
function, however, the pin can still be used as a normal input pin. The PFD output will only be activated if bit PA3 is
set to ²1². This output data bit is used as the on/off control
bit for the PFD output. Note that the PFD output will be low
if the PA3 output data bit is cleared to ²0².
register is full, the microcontroller will generate an internal interrupt signal directing the program flow to the respective internal interrupt vector. For the pulse width
measurement mode, the internal system clock is also
used as the timer clock source but the timer will only run
when the correct logic condition appears on the external
timer input pin. As this is an external event and not synch r o n i ze d w i t h t h e i n t e r n a l t i m e r cl o ck, t h e
microcontroller will only see this external event when the
next timer clock pulse arrives. As a result, there may be
small differences in measured values requiring programmers to take this into account during programming.
The same applies if the timer is configured to be in the
event counting mode, which again is an external event
and not synchronised with the internal system or timer
clock.
Using this method of frequency generation, and if a
crystal oscillator is used for the system clock, very precise values of frequency can be generated.
Prescaler
Bits T0PSC0~T0PSC2 of the TMR0C register can be
used to define the pre-scaling stages of the internal
clock sources of the Timer/Event Counter 0. The
Timer/Event Counter overflow signal can be used to
generate signals for the PFD and Timer Interrupt.
When the Timer/Event Counter is read, or if data is written to the preload register, the clock is inhibited to avoid
errors, however as this may result in a counting error, this
should be taken into account by the programmer. Care
must be taken to ensure that the timers are properly initialised before using them for the first time. The associated timer enable bits in the interrupt control register must
be properly set otherwise the internal interrupt associated
with the timer will remain inactive. The edge select, timer
mode and clock source control bits in timer control register must also be correctly set to ensure the timer is properly configured for the required application. It is also
important to ensure that an initial value is first loaded into
the timer registers before the timer is switched on; this is
because after power-on the initial values of the timer registers are unknown. After the timer has been initialised
the timer can be turned on and off by controlling the enable bit in the timer control register. Note that setting the
timer enable bit high to turn the timer on, should only be
executed after the timer mode bits have been properly
setup. Setting the timer enable bit high together with a
mode bit modification, may lead to improper timer operation if executed as a single timer control register byte
write instruction.
I/O Interfacing
The Timer/Event Counter, when configured to run in the
event counter or pulse width measurement mode, require the use of the external pin for correct operation. As
this pin is a shared pin it must be configured correctly to
ensure it is setup for use as a Timer/Event Counter input
and not as a normal I/O pin. This is implemented by ensuring that the mode select bits in the Timer/Event
Counter control register, select either the event counter
or pulse width measurement mode. Additionally the Port
Control Register must be set high to ensure that the pin
is setup as an input. Any pull-high resistor on this pin will
remain valid even if the pin is used as a Timer/Event
Counter input.
Timer/Event Counter Pins Internal Filter
The external Timer/Event Counter pins are connected to
an internal filter to reduce the possibility of unwanted
event counting events or inaccurate pulse width measurements due to adverse noise or spikes on the external Timer/Event Counter input signal. As this internal
filter circuit will consume a limited amount of power, a
configuration option is provided to switch off the filter
function, an option which may be beneficial in power
sensitive applications, but in which the integrity of the input signal is high. Care must be taken when using the filter on/off configuration option as it will be applied not
only to both external Timer/Event Counter pins but also
to the external interrupt input pins. Individual
Timer/Event Counter or external interrupt pins cannot
be selected to have a filter on/off function.
When the Timer/Event counter overflows, its corresponding interrupt request flag in the interrupt control
register will be set. If the timer interrupt is enabled this
will in turn generate an interrupt signal. However irrespective of whether the interrupts are enabled or not, a
Timer/Event counter overflow will also generate a
wake-up signal if the device is in a Power-down condition. This situation may occur if the Timer/Event Counter
is in the Event Counting Mode and if the external signal
continues to change state. In such a case, the
Timer/Event Counter will continue to count these external events and if an overflow occurs the device will be
woken up from its Power-down condition. To prevent
such a wake-up from occurring, the timer interrupt request flag should first be set high before issuing the
HALT instruction to enter the Power Down Mode.
Programming Considerations
When configured to run in the timer mode, the internal
system clock is used as the timer clock source and is
therefore synchronised with the overall operation of the
microcontroller. In this mode when the appropriate timer
Rev. 1.40
35
September 8, 2009
HT56R64
Timer Program Example
This program example shows how the Timer/Event Counter registers are setup, along with how the interrupts are enabled and managed. Note how the Timer/Event Counter is turned on, by setting bit 4 of the Timer Control Register. The
Timer/Event Counter can be turned off in a similar way by clearing the same bit. This example program sets the
Timer/Event Counter to be in the timer mode, which uses the internal system clock as the clock source.
org 04h
; external interrupt vector
reti
org 08h
; Timer/Event Counter 0 interrupt vector
jmp tmrint
; jump here when the Timer/Event Counter 0 overflows
:
org 20h
; main program
;internal Timer/Event Counter 0 interrupt routine
tmrint:
:
; Timer/Event Counter 0 main program placed here
:
reti
:
:
begin:
;setup Timer 0 registers
mov a,09bh
; setup Timer 0 preload value
mov tmr0,a;
mov a,081h
; setup Timer 0 control register
mov tmr0c,a
; timer mode and prescaler set to /2
; setup interrupt register
mov a,009h
; enable master interrupt and timer interrupt
mov int0c,a
set tmr0c.4
; start Timer/Event Counter 0 - note mode bits must be previously setup
Rev. 1.40
36
September 8, 2009
HT56R64
Pulse Width Modulator
The device contains four Pulse Width Modulation,
PWM, outputs. Useful for such applications such as motor speed control, the PWM function provides an output
with a fixed frequency but with a duty cycle that can be
varied by setting particular values into the corresponding PWM register.
Channel
PWM
Mode
Output
Pin
Register
Names
1
8+4
PD0
PWM0L
PWM0H
2
8+4
PD1
PWM1L
PWM1H
3
8+4
PD2
PWM2L
PWM2H
4
8+4
PD3
PWM3L
PWM3H
as modulation cycle 0 ~ modulation cycle 15, denoted as
²i² in the table. Each one of these sixteen sub-cycles contains 256 clock cycles. In this mode, a modulation frequency increase of sixteen is achieved. The 12-bit PWM
register value, which represents the overall duty cycle of
the PWM waveform, is divided into two groups. The first
group which consists of bit4~bit11 is denoted here as the
DC value. The second group which consists of bit0~bit3
is known as the AC value. In the 8+4 PWM mode, the
duty cycle value of each of the two modulation sub-cycles
is shown in the following table.
Parameter
Modulation cycle i
(i=0~15)
AC (0~15)
DC (Duty Cycle)
i<AC
DC+1
256
i³AC
DC
256
8+4 Mode Modulation Cycle Values
PWM Overview
The accompanying diagram illustrates the waveforms
associated with the 8+4 mode of PWM operation. It is
important to note how the single PWM cycle is subdivided into 16 individual modulation cycles, numbered
0~15 and how the AC value is related to the PWM value.
Four register pairs, located in the Data Memory are assigned to the Pulse Width Modulator and are known as
the PWM registers. It is in each register pair that the
12-bit value, which represents the overall duty cycle of
one modulation cycle of the output waveform, should be
placed. The PWM registers also contain the enable/disable control bit for the PWM outputs. To increase the
PWM modulation frequency, each modulation cycle is
modulated into sixteen individual modulation
sub-sections, known as the 8+4 mode. Note that it is
only necessary to write the required modulation value
into the corresponding PWM register as the subdivision
of the waveform into its sub-modulation cycles is implemented automatically within the microcontroller hardware. The PWM clock source is the system clock fSYS.
PWM Output Control
PWM
Modulation
Frequency
PWM Cycle
Frequency
PWM Cycle
Duty
fSYS/256
fSYS/4096
(PWM register
value)/4096
The four PWM0~PWM3 outputs are shared with pins
PD0~PD3. To operate as a PWM output and not as an
I/O pin, bit 0 of the relevant PWM register bit must be set
high. A zero must also be written to the corresponding
bit in the PDC port control register, to ensure that the
PWM0 output pin is setup as an output. After these two
initial steps have been carried out, and of course after
the required PWM 12-bit value has been written into the
PWM register pair register, writing a ²1² to the corresponding PD data register will enable the PWM data to
appear on the pin. Writing a ²0² to the bit will disable the
PWM output function and force the output low. In this
way, the Port D data output register bits, can also be
used as an on/off control for the PWM function. Note
that if the enable bit in the PWM register is set high to
enable the PWM function, but a ²1² has been written to
its corresponding bit in the PDC control register to configure the pin as an input, then the pin can still function
as a normal input line, with pull-high resistor selections.
This method of dividing the original modulation cycle
into a further 16 sub-cycles enables the generation of
higher PWM frequencies, which allow a wider range of
applications to be served. As long as the periods of the
generated PWM pulses are less than the time constants
of the load, the PWM output will be suitable as such long
time constant loads will average out the pulses of the
PWM output. The difference between what is known as
the PWM cycle frequency and the PWM modulation frequency should be understood. As the PWM clock is the
system clock, fSYS, and as the PWM value is 12-bits
wide, the overall PWM cycle frequency is fSYS/4096.
However, when in the 8+4 mode of operation, the PWM
modulation frequency will be fSYS/256.
8+4 PWM Mode Modulation
Each full PWM cycle, as it is 12-bits wide, has 4096 clock
periods. However, in the 8+4 PWM mode, each PWM cycle is subdivided into sixteen individual sub-cycles known
Rev. 1.40
37
September 8, 2009
HT56R64
8+4 PWM Mode
P W M 0 H ~ P W M 3 H
H ig h B y te R e g is te r s
b 7
1 1
1 0
9
8
7
6
5
P W M 0 L ~ P W M 3 L
L o w B y te R e g is te r s
b 0
4
b 7
3
2
1
0
b 0
P W M n E N
P W M
R e g is te r s
P W M O n /O ff C o n tro l
1 : P W M e n a b le
0 : I/O p in e n a b le
N o t im p le m e n te d , r e a d a s " 0 "
P W M A C
b its 0 ~ 3
V a lu e
P W M D C V a lu e
b its 4 ~ 1 1
PWM Register Pairs
PWM Programming Example
The following sample program shows how the PWM output is setup and controlled.
mov
mov
clr
clr
set
set
:
:
clr
a,64h
pwm0h,a
pwm0l
pdc.0
pwm0en
pd.0
:
:
pd.0
Rev. 1.40
;
;
;
;
;
;
setup PWM0 value to 1600 decimal which is 640H
setup PWM0H register value
setup PWM0L register value
setup pin PD0 as an output
set the PWM0 enable bit
Enable the PWM0 output
; PWM0 output disabled - PD0 will remain low
38
September 8, 2009
HT56R64
Analog to Digital Converter
The need to interface to real world analog signals is a
common requirement for many electronic systems.
However, to properly process these signals by a
microcontroller, they must first be converted into digital
signals by A/D converters. By integrating the A/D conversion electronic circuitry into the microcontroller, the
need for external components is reduced significantly
with the corresponding follow-on benefits of lower costs
and reduced component space requirements.
Conversion Bits
Input Pins
12
PB0~PB7
Bit
5
Bit
4
Bit
3
Bit
2
Bit
1
Bit
0
ADRL
D3
D2
D1
D0
¾
¾
¾
¾
ADRH
D11 D10 D9
D8
D7
D6
D5
D4
To control the function and operation of the A/D converter, two control registers known as ADCR and ACSR
are provided. These 8-bit registers define functions
such as the selection of which analog channel is connected to the internal A/D converter, which pins are
used as analog inputs and which are used as normal
I/Os, the A/D clock source as well as controlling the start
function and monitoring the A/D converter end of conversion status.
The ACS2~ACS0 bits in the ADCR register define the
channel number. As the device contains only one actual
analog to digital converter circuit, each of the individual
8 analog inputs must be routed to the converter. It is the
function of the ACS2~ACS0 bits in the ADCR register to
determine which analog channel is actually connected
to the internal A/D converter.
The accompanying block diagram shows the overall internal structure of the A/D converter, together with its
associated registers.
A/D Converter Data Registers - ADRL, ADRH
The device, which has an internal 12-bit A/D converter,
requires two data registers, a high byte register, known
as ADRH, and a low byte register, known as ADRL. After
the conversion process takes place, these registers can
be directly read by the microcontroller to obtain the digitised conversion value. Only the high byte register,
ADRH, utilises its full 8-bit contents. The low byte register utilises only 4 bit of its 8-bit contents as it contains
only the lowest bits of the 12-bit converted value.
The ADCR control register also contains the
PCR2~PCR0 bits which determine which pins on Port B
are used as analog inputs for the A/D converter and
which pins are to be used as normal I/O pins. If the 3-bit
address on PCR2~PCR0 has a value of ²111², then all
eight pins, namely AN0~AN7 will all be set as analog inputs. Note that if the PCR2~PCR0 bits are all set to zero,
then all the Port B pins will be setup as normal I/Os and
the internal A/D converter circuitry will be powered off to
reduce the power consumption.
In the following table, D0~D11 is the A/D conversion
data result bits.
fS
A C S R
Bit
6
A/D Converter Control Registers - ADCR, ACSR
The device contains an 8-channel analog to digital converter which can directly interface to external analog signals, such as that from sensors or other control signals
and convert these signals directly into either a 12-bit digital value.
8
Bit
7
A/D Data Registers
A/D Overview
Input Channels
Register
Y S
C lo c k
D iv id e r
¸ N
R e g is te r
A D O N B B it
A /D E n a b le
A /D
P B 0 /A N 0
P B 1 /A N 1
R e fe r e n c e V o lta g e
A V D D
A /D P o s itiv e P o w e r S u p p ly
A D R L
A D C
A D R H
P B 7 /A N 7
A /D
A V
P C R 0 ~ P C R 2
P in C o n fig u r a tio n
B its
A D C S 0 ~ A D C S 2
C h a n n e l S e le c t
B its
S T A R T
E O C B
A /D D a ta
R e g is te r s
G ro u n d
S S
A D C R
R e g is te r
S ta r t B it E n d o f
C o n v e r s io n B it
A/D Converter Structure
Rev. 1.40
39
September 8, 2009
HT56R64
b 7
S T A R T E O C B
P C R 2
P C R 1
P C R 0
A C S 2
A C S 1
b 0
A C S 0
A D C R
R e g is te r
S e le c t A /D
A
A C S 2
0
0
0
0
1
1
1
1
c h a n n e l
C S 1 A C S 0
0
0
1
0
0
1
1
1
0
0
1
0
0
1
1
1
P o rt B A /D
P
P C R 2
0
0
0
0
1
1
1
1
c h a n n e l c o n fig
C R 1 P C R 0
P
0
0
P
1
0
P
0
1
P
1
1
P
0
0
P
1
0
P
0
1
1
1
P
A N 0
A N 1
A N 2
A N 3
A N 4
A N 5
A N 6
A N 7
u r a tio n s
o rt
B 0
B 0
B 0
B 0
B 0
B 0
B 0
B A
e n a
~ P B
~ P B
~ P B
~ P B
~ P B
~ P B
/D
b
1
2
3
4
5
7
c h a n n
le d a s A
e n a b le
e n a b le
e n a b le
e n a b le
e n a b le
e n a b le
e ls
N 0
d a
d a
d a
d a
d a
d a
- a ll o ff
s A N
s A N
s A N
s A N
s A N
s A N
0 ~ A
0 ~ A
0 ~ A
0 ~ A
0 ~ A
0 ~ A
N 1
N 2
N 3
N 4
N 5
N 7
E n d o f A /D c o n v e r s io n fla g
1 : A /D c o n v e r s io n w a itin g o r in p r o g r e s s
0 : A /D c o n v e r s io n e n d e d
S ta r t th e A /D c o n v e r s io n
0 ® 1 ® 0 : S ta rt
0 ® 1 : R e s e t A /D c o n v e rte r a n d s e t E O C B to "1 "
A/D Converter Control Register - ADCR
Controlling the on/off function of the A/D converter circuitry is implemented using the ADONB bit in the ACSR
register and the value of the PCR bits in the ADCR register. Both the ADONB bit must cleared to ²0² and the
value of the PCR bits must have a non-zero value for the
A/D converter to be enabled.
The START bit in the ADCR register is used to start and
reset the A/D converter. When the microcontroller sets
this bit from low to high and then low again, an analog to
digital conversion cycle will be initiated. When the
START bit is brought from low to high but not low again,
the EOCB bit in the ADCR register will be set to a ²1²
and the analog to digital converter will be reset. It is the
START bit that is used to control the overall on/off operation of the internal analog to digital converter.
The EOCB bit in the ADCR register is used to indicate
when the analog to digital conversion process is complete. This bit will be automatically set to ²0² by the
microcontroller after a conversion cycle has ended. In
addition, the corresponding A/D interrupt request flag
will be set in the interrupt control register, and if the interrupts are enabled, an appropriate internal interrupt signal will be generated. This A/D internal interrupt signal
will direct the program flow to the associated A/D internal interrupt address for processing. If the A/D internal
interrupt is disabled, the microcontroller can be used to
poll the EOCB bit in the ADCR register to check whether
it has been cleared as an alternative method of detecting the end of an A/D conversion cycle.
ADONB
A/D
0
x
Off
>0
0
On
>0
1
Off
Although the A/D clock source is determined by the system clock fSYS, and by bits ADCS2, ADCS1 and ADCS0,
there are some limitations on the maximum A/D clock
source speed that can be selected. As the minimum value
of permissible A/D clock period, tAD, is 0.5ms, care must be
taken for system clock speeds in excess of 4MHz. For
system clock speeds in excess of 4MHz, the ADCS2,
ADCS1 and ADCS0 bits should not be set to ²000². Doing
so will give A/D clock periods that are less than the minimum A/D clock period which may result in inaccurate A/D
conversion values. Refer to the following table for examples, where values marked with an asterisk * show where,
depending upon the device, special care must be taken,
as the values may be less than the specified minimum A/D
Clock Period.
The clock source for the A/D converter, which originates
from the system clock fSYS, is first divided by a division
ratio, the value of which is determined by the ADCS2,
ADCS1 and ADCS0 bits in the ACSR register.
Rev. 1.40
PCR
40
September 8, 2009
HT56R64
A/D Clock Period (tAD)
fSYS
ADCS2, ADCS1,
ADCS0=000
(fSYS/2)
ADCS2, ADCS1,
ADCS0=001
(fSYS/8)
ADCS2, ADCS1,
ADCS0=010
(fSYS/32)
ADCS2, ADCS1,
ADCS0=011
1MHz
2ms
8ms
32ms
Undefined
2MHz
1ms
4ms
16ms
Undefined
4MHz
500ns*
2ms
8ms
Undefined
8MHz
250ns*
1ms
4ms
Undefined
12MHz
167ns*
667ns*
2.67ms
Undefined
A/D Clock Period Examples
b 7
T E S T
A D O N B
b 0
A D C S 2 A D C S 1 A D C S 0
A C S R R e g is te r
S e le c t A /D c o n v e r te r c lo c k s o u r
A D C S 0
A D C S 2
A D C S 1
:
0
0
0
:
1
0
0
:
0
0
1
:
1
0
1
:
0
1
0
:
1
1
0
:
0
1
1
:
1
1
1
c e
s y s
s y s
s y s
u n d
s y s
s y s
s y s
u n d
te m
te m
te m
e fin
te m
te m
te m
e fin
c lo
c lo
c lo
e d
c lo
c lo
c lo
e d
c k /2
c k /8
c k /3 2
c k
c k /4
c k /1 6
N o t im p le m e n te d , r e a d a s " 0 "
A /D O n /O ff c o n tr o l b it
1 : d is a b le
0 : e n a b le
F o r te s t m o d e u s e o n ly
A/D Converter Control Register - ACSR
A/D Input Pins
the channel selection bits have changed, then, within a
time frame of one to ten instruction cycles, the START bit
in the ADCR register must first be set high and then immediately cleared to zero. This will ensure that the EOCB
flag is correctly set to a high condition.
All of the A/D analog input pins are pin-shared with the
I/O pins on Port B. Bits PCR2~PCR0 in the ADCR register, determine whether the input pins are setup as normal Port B input/output pins or whether they are setup
as analog inputs. In this way, pins can be changed under
program control to change their function from normal I/O
operation to analog inputs and vice versa. Pull-high resistors, which are setup through register programming,
apply to the input pins only when they are used as normal I/O pins, if setup as A/D inputs the pull-high resistors
will be automatically disconnected. Note that it is not
necessary to first setup the A/D pin as an input in the
PBC port control register to enable the A/D input as
when the PCR2~PCR0 bits enable an A/D input, the status of the port control register will be overridden. The
A/D converter has its own power supply pins AVDD and
AVSS and a VREF reference pin. The analog input values must not be allowed to exceed the value of VREF.
Summary of A/D Conversion Steps
The following summarises the individual steps that
should be executed in order to implement an A/D conversion process.
· Step 1
Select the required A/D conversion clock by correctly
programming bits ADCS2, ADCS1 and ADCS0 in the
ACSR register.
· Step 2
Enable the A/D by clearing the ADONB in the ACSR
register to zero.
· Step 3
Select which channel is to be connected to the internal
A/D converter by correctly programming the
ACS2~ACS0 bits which are also contained in the
ADCR register.
Initialising the A/D Converter
The internal A/D converter must be initialised in a special
way. Each time the Port B A/D channel selection bits are
modified by the program, the A/D converter must be
re-initialised. If the A/D converter is not initialised after the
channel selection bits are changed, the EOCB flag may
have an undefined value, which may produce a false end
of conversion signal. To initialise the A/D converter after
Rev. 1.40
· Step 4
Select which pins on Port B are to be used as A/D inputs and configure them as A/D input pins by correctly
programming the PCR2~PCR0 bits in the ADCR register. Note that this step can be combined with Step 2
into a single ADCR register programming operation.
41
September 8, 2009
HT56R64
P C R 2 ~
P C R 0
0 0 0 B
1 0 1 B
1 0 0 B
0 0 0 B
A D O N B
tO
A D C
m o d u le
O N
N 2 S T
o n
A /D
tA
s a m p lin g tim e
A /D
tA
D C S
o ff
s a m p lin g tim e
o n
o ff
D C S
S T A R T
E O C B
A C S 2 ~
A C S 0
x x x B
P o w e r-o n
R e s e t
0 1 0 B
0 0 0 B
0 0 1 B
S ta rt o f A /D
c o n v e r s io n
S ta rt o f A /D
c o n v e r s io n
S ta rt o f A /D
c o n v e r s io n
R e s e t A /D
c o n v e rte r
R e s e t A /D
c o n v e rte r
A /D
N o te :
R e s e t A /D
c o n v e rte r
E n d o f A /D
c o n v e r s io n
1 : D e fin e p o r t c o n fig u r a tio n
2 : S e le c t a n a lo g c h a n n e l
x x x B
E n d o f A /D
c o n v e r s io n
tA D C
c o n v e r s io n tim e
A /D
A /D c lo c k m u s t b e fs y s , fS Y S /2 , fS Y S /4 , fS Y S /8 , fS Y S /1 6 o r fS
tA D C S = 4 tA D
tA D C = tA D C S + n * tA D ; n = b it c o u n t o f A D C r e s o lu tio n
Y S
tA D C
c o n v e r s io n tim e
/3 2
A/D Conversion Timing
· Step 5
during which time the program can continue with other
functions. The time taken for the A/D conversion is 16tAD
where tAD is equal to the A/D clock period.
If the interrupts are to be used, the interrupt control registers must be correctly configured to ensure the A/D
converter interrupt function is active. The master interrupt control bit, EMI, in the INTC0 interrupt control register must be set to ²1², the multi-function interrupt
enable bit, EMFI, in the INTC1 register and the A/D
converter interrupt bit, EADI, in the INTC1 register
must also be set to ²1².
Programming Considerations
When programming, special attention must be given to
the A/D channel selection bits in the ADCR register. If
these bits are all cleared to zero no external pins will be
selected for use as A/D input pins allowing the pins to be
used as normal I/O pins. When this happens the power
supplied to the internal A/D circuitry will be reduced resulting in a reduction of supply current. This ability to reduce power by turning off the internal A/D function by
clearing the A/D channel selection bits may be an important consideration in battery powered applications. The
ADONB bit in the ACSR register can also be used to
power down the A/D function.
· Step 6
The analog to digital conversion process can now be
initialised by setting the START bit in the ADCR register from ²0² to ²1² and then to ²0² again. Note that this
bit should have been originally set to ²0².
· Step 7
To check when the analog to digital conversion process is complete, the EOCB bit in the ADCR register
can be polled. The conversion process is complete
when this bit goes low. When this occurs the A/D data
registers ADRL and ADRH can be read to obtain the
conversion value. As an alternative method if the interrupts are enabled and the stack is not full, the program can wait for an A/D interrupt to occur.
Note:
Another important programming consideration is that
when the A/D channel selection bits change value, the
A/D converter must be re-initialised. This is achieved by
pulsing the START bit in the ADCR register immediately
after the channel selection bits have changed state. The
exception to this is where the channel selection bits are
all cleared, in which case the A/D converter is not required to be re-initialised.
When checking for the end of the conversion
process, if the method of polling the EOCB bit in
the ADCR register is used, the interrupt enable
step above can be omitted.
A/D Programming Example
The accompanying diagram shows graphically the various stages involved in an analog to digital conversion
process and its associated timing.
The following two programming examples illustrate how
to setup and implement an A/D conversion. In the first
example, the method of polling the EOCB bit in the
ADCR register is used to detect when the conversion
cycle is complete, whereas in the second example, the
A/D interrupt is used to determine when the conversion
is complete.
The setting up and operation of the A/D converter function is fully under the control of the application program as
there are no configuration options associated with the
A/D converter. After an A/D conversion process has been
initiated by the application program, the microcontroller
internal hardware will begin to carry out the conversion,
Rev. 1.40
42
September 8, 2009
HT56R64
Example: using an EOCB polling method to detect the end of conversion
clr EADI
; disable ADC interrupt
mov a,00000001B
mov ACSR,a
; select fSYS/8 as A/D clock and turn on ADONB bit
mov a,00100000B
; setup ADCR register to configure Port PB0~PB3
; as A/D inputs
mov ADCR,a
; and select AN0 to be connected to the A/D converter
:
:
; As the Port B channel bits have changed the
; following START
; signal (0-1-0) must be issued
; instruction cycles
:
Start_conversion:
clr START
set START
; reset A/D
clr START
; start A/D
Polling_EOC:
sz
EOCB
; poll the ADCR register EOCB bit to detect end
; of A/D conversion
jmp polling_EOC
; continue polling
mov a,ADRL
; read low byte conversion result value
mov adrl_buffer,a
; save result to user defined register
mov a,ADRH
; read high byte conversion result value
mov adrh_buffer,a
; save result to user defined register
:
jmp start_conversion
; start next A/D conversion
Example: using the interrupt method to detect the end of conversion
clr EADI
; disable ADC interrupt
mov a,00000001B
mov ACSR,a
; select fSYS/8 as A/D clock and turn on ADONB bit
mov
a,00100000B
mov
ADCR,a
:
; setup ADCR register to configure Port PB0~PB3
; as A/D inputs
; and select AN0 to be connected to the A/D
; As the Port B channel bits have changed the
; following START signal(0-1-0) must be issued
;
:
Start_conversion:
clr START
set START
clr START
clr ADF
set EADI
Set EMFI
set EMI
:
:
:
; ADC interrupt service routine
ADC_:
mov acc_stack,a
mov a,STATUS
mov status_stack,a
:
:
mov a,ADRL
mov adrl_buffer,a
mov a,ADRH
mov adrh_buffer,a
:
:
EXIT__ISR:
mov a,status_stack
mov STATUS,a
mov a,acc_stack
clr ADF
reti
Rev. 1.40
;
;
;
;
;
;
reset A/D
start A/D
clear ADC interrupt request flag
enable ADC interrupt
enable multi-function interrupt
enable global interrupt
; save ACC to user defined memory
; save STATUS to user defined memory
;
;
;
;
read
save
read
save
low byte conversion result value
result to user defined register
high byte conversion result value
result to user defined register
; restore STATUS from user defined memory
; restore ACC from user defined memory
; clear ADC interrupt flag
43
September 8, 2009
HT56R64
· SPI Interface Operation
A/D Transfer Function
The SPI interface is a full duplex synchronous serial
data link. Communication between devices connected to the SPI interface is carried out in a
slave/master mode with all data transfer initiations being implemented by the master. Multiple slave devices
can be connected to the SPI serial bus with each device controlled using its slave select line. The SPI is a
four line interface with pin names SDI, SDO, SCK and
SCS. Pins SDI and SDO are the Serial Data Input and
Serial Data Output lines, SCK is the Serial Clock line
and SCS is the Slave Select line. As the SPI interface
pins are pin-shared with segment pins and with the
I2C function pins, the SPI interface must first be enabled by selecting the correct configuration option. After the SPI configuration option has been selected it
can then also be selected using the SIMEN bit in the
SIMCON0 register.
As the device contain a 12-bit A/D converter, its
full-scale converted digitised value is equal to FFFH.
Since the full-scale analog input value is equal to the
VDD voltage, this gives a single bit analog input value of
VDD/4096. The diagram show the ideal transfer function
between the analog input value and the digitised output
value for the A/D converter.
Note that to reduce the quantisation error, a 0.5 LSB offset is added to the A/D Converter input. Except for the
digitised zero value, the subsequent digitised values will
change at a point 0.5 LSB below where they would
change without the offset, and the last full scale digitised
value will change at a point 1.5 LSB below the VDD level.
Serial Interface
The device contains both SPI and I2C serial interface
functions, which allows two methods of easy communication with external peripheral hardware. As the SPI and
I2C function share the same external pins and internal
registers their function must first be chosen by selecting
the correct configuration option.
The SPI function in this device offers the following features:
SPI Interface
The SPI interface is often used to communicate with external peripheral devices such as sensors, Flash or
EEPROM memory devices etc. Originally developed by
Motorola, the four line SPI interface is a synchronous
serial data interface that has a relatively simple communication protocol simplifying the programming requirements when communicating with external hardware
devices.
¨
Full duplex synchronous data transfer
¨
Both Master and Slave modes
¨
LSB first or MSB first data transmission modes
¨
Transmission complete flag
¨
Supports UART interface bridge
¨
IDLE mode supported
Several other configuration options also exist to setup
various SPI interface options as follows:
¨
SPI pin enabled
¨
Rising or falling active clock edge
¨
WCOL bit enabled or disabled
¨
CSEN bit enabled or disabled
1 .5 L S B
F F F H
F F E H
F F D H
A /D C o n v e r s io n
R e s u lt
0 .5 L S B
0 3 H
0 2 H
0 1 H
0
1
2
3
4 0 9 3 4 0 9 4
4 0 9 5 4 0 9 6
(
V D D
)
4 0 9 6
A n a lo g In p u t V o lta g e
Ideal A/D Transfer Function
Rev. 1.40
44
September 8, 2009
HT56R64
The status of the SPI interface pins is determined by a number of factors, whether the device is in master or slave
mode and upon the condition of certain control bits such as CSEN and SIMEN.
Master (SIMEN=1)
Slave (=1)
Master/Salve
(SIMEN=0)
CSEN=1
CSEN=0
CSEN=0
SCS line=0
(CSEN=1)
SCS line=1
(CSEN=1)
SCS
Z
L
Z
Z
I, Z
I, Z
SDO
Z
O
O
O
O
Z
SDI
Z
I, Z
I, Z
I, Z
I, Z
Z
SCK
Z
L(CPOL=1)
H(CPOL=0)
L(CPOL=1)
H(CPOL=0)
I, Z
I, Z
Z
²Z² floating, ²H² output high, ²L² output low, ²I² Input, ²O²output level, ²I,Z² input floating (no pull-high)
SPI Interface Pin Status
· SPI Registers
SCK and SCS lines will be in a floating condition
and the SPI operating current will be reduced to
<0.1mA at 5V. When the bit is high the SPI interface
is enabled. Note that when the SIMEN bit changes
from low to high the contents of the SPI control registers will be in an unknown condition and should
therefore be initialised by the application program.
The SIMDR register is used to store the data being
transmitted and received. There are two control registers associated with the SPI interface, SIMCON0 and
SIMCON2 and one data register known as SIMDR.
The SIMCON1 register is not used by the SPI function. Register SIMCON0 is used to control the enable/disable function, the power down control and to
set the data transmission clock frequency. Register
SIMCON2 is used for other control functions such as
LSB/MSB selection, write collision flag etc.
The following gives further explanation of each bit:
¨
¨
SIMEN
The SIMEN bit is the overall on/off control for the
SPI interface. When the SIMEN bit is cleared to
zero to disable the SPI interface, the SDI, SCO,
SIMIDLE
The SIMIDLE bit is used to select if the SPI interface
continues running when the device is in the IDLE
mode. Setting the bit high allows the SPI clock to
keep running and enables the SPI interface to maintain operation when the device is in the Idle mode.
Clearing the bit to zero disables any SPI operations
when in the Idle mode.
D a ta B u s
S IM D R
( R e c e iv e d D a ta R e g is te r )
D 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0
M
S D O
U
X
M
S C K
a n d , s ta rt
M
a n d , s ta rt
C lo c k P o la r ity
U
X
E N
S D O
S IM E N
M L S
In te r n a l B a u d R a te C lo c k
B u ffe r
S D I
U
X
T R F
C 0 C 1 C 2
M a s te r o r S la v e
a n d , s ta rt
E N
W C O L F la g
A N D
In te r n a l B u s y F la g
S IM E N
W r ite S B D R
W r ite S IM D R
S IM E N
E n a b le /D is a b le
W r ite S IM D R
S C S
M a s te r o r S la v e
S IM E N
C S E N
Block Diagram
Rev. 1.40
45
September 8, 2009
HT56R64
b 7
S IM 2
b 0
S IM 1
S IM 0
P C K E N
P C K P S C 1 P C K P S C 0 S IM E N
S IM ID L E
S IM C O N 0 R e g is te r
S P I S ta tu s in Id le M o d e
1 : e n a b le
0 : d is a b le
S P I O n /O f c o n tro l
1 : e n a b le
0 : d is a b le
P e r ip h e r a l C lo c k C o n tr o l d e s c r ib e d e ls e w h e r e
S P I M a s te r /S la v e a n d C lo c k
S IM 2
S IM 1
S IM 0
0
m a s
0
0
0
m a s
0
1
1
0
0
m a s
1
0
1
m a s
0
1
0
m a s
0
1
1
S la v
1
1
0
N o t
1
1
1
N o t
C o n tro l
te
te
te
te
te
e
r,
r,
r,
r,
r,
fS
fS
fS
fS
Y S
Y S
Y S
/4
/1 6
/6 4
U B
T im e r /E v e n t C o u n te r 0 o u tp u t/2
u s e d
u s e d
SPI Control Register - SIMCON0
b 0
b 7
M L S
C S E N
W C O L
T R F
S IM C O N 2 R e g is te r
T r a n s m it/R e c e iv e c o m p le te fla g
1 : d a ta tr a n s fe r c o m p le te
0 : d a ta tr a n s fe r in c o m p le te
W r ite c o llis io n fla g
1 : d a ta c o llis io n
0 : n o c o llis io n
S C S p in e n a b le
1 : e n a b le
0 : d is a b le , S C S flo a tin g
D a ta s h ift o r d e r
1 : M S B fir s t
0 : L S B fir s t
N o t im p le m e n te d , r e a d a s " 0 "
SPI Control Register - SIMCON2
T M R 0 O u tp u t /2
P C K P S C 1
P C K P S C 0
P C K E N
P C K O u tp u t
C lo c k S e le c to r
fS
S le e p
M o d e
Id le M o d e
S IM ID L E
Y S
S P I/I2C
S IM E N
S IM
S IM
[2 :0 ] ¹ 1 1 1
M o d u le S tr u c tu r e
N o te : S le e p M o d e = H A L T & ID L E N = 0
Id le M o d e = H A L T & ID L E N = 1
SPI SIM Module Structure
Rev. 1.40
46
September 8, 2009
HT56R64
¨
SIM0~SIM2
These three bits control the Master/Slave selection
and also setup the SPI interface clock speed when
in the Master Mode. The SPI clock is a function of
the system clock whether it be RC type or Crystal
type but can also be chosen to be sourced from
Timer/Event Counter 0 divided by two. If the Slave
Mode is selected then the clock will be supplied by
the external Master device.
The following gives further explanation of each bit:
¨
¨
TRF
The TRF bit is the Transmit/Receive Complete flag
and is cleared by the application program and can
be used to generate an interrupt. When the bit is
high the data has been transmitted or received. If
the bit is low the data is being transmitted or has not
yet been received.
¨
CSEN
The CSEN bit is used as an on/off control for the
SCS pin. If this bit is low then the SCS pin will be disabled and placed into a floating condition. If the bit is
high the SCS pin will be enabled and used as a select pin.
¨
MLS
The MLS is used to select how the data is transferred, either MSB or LSB first. Setting the bit high
will select MSB first and low for LSB first.
Note that the SIMCON2 register is the same as the
SIMAR register used by the I2C interface.
· SPI Communication
After the SPI interface is enabled by setting the
SIMEN bit high, then in the Master Mode, when data is
written to the SIMDR register, transmission/reception
will begin simultaneously. When the data transfer is
complete, the TRF flag will be set automatically. In the
Slave Mode, when the clock signal from the master
has been received, any data in the SIMDR register will
be transmitted and any data on the SDI pin will be
shifted into the SIMDR register. The master should
output an SCS signal before a clock signal is provided
and slave data transfers should be enabled/disabled
before/after an SCS signal is received.
WCOL
The WCOL bit is used to detect if a data collision
has occurred. If this bit is high it means that data
has been attempted to be written to the SMDR register during a data transfer operation. This writing
operation will be ignored if data is being transferred.
The bit can be cleared by the application program.
Note that using the SCEN bit can be disabled or enabled via configuration option.
S IM E N = 1 , C S E N = 0 a n d w r ite d a ta to S IM D R ( if p u lle d h ig h )
S C S
S IM E N = C S E N = 1 a n d w r ite d a ta to S IM D R
S C K
S D I
S D O
D 7 /D 0 D 6 /D 1 D 5 /D 2 D 4 /D 3 D 3 /D 4 D 2 /D 5 D 1 /D 6 D 0 /D 7
D 7 /D 0 D 6 /D 1 D 5 /D 2 D 4 /D 3 D 3 /D 4 D 2 /D 5 D 1 /D 6 D 0 /D 7
S C K
SPI Interface Timing
Rev. 1.40
47
September 8, 2009
HT56R64
A
S P I tra n s fe r
W r ite D a ta
in to S IM D R
C le a r W C O L
m a s te r
m a s te r o r
s la v e
S IM [2 :0 ]= 0 0 0 ,
0 0 1 ,0 1 0 ,0 1 1 o r 1 0 0
s la v e
Y
W C O L = 1 ?
S IM [2 :0 ]= 1 0 1
N
c o n fig u r e
C S E N a n d M L S
T r a n s m is s io n
c o m p le te d ?
(T R F = 1 ? )
Y
R e a d D a ta
fro m S IM D R
S IM E N = 1
C le a r T R F
A
T ra n s fe r
F in is h e d ?
N
Y
E N D
SPI Transfer Control Flowchart
Rev. 1.40
48
September 8, 2009
HT56R64
I2C Interface
· I2C Registers
There are three control registers associated with the
I2C bus, SIMCON0, SIMCON1 and SIMAR and one
data register, SIMDR.
The SIMDR register is used to store the data being
transmitted and received on the I2C bus. Before the
microcontroller writes data to the I2C bus, the actual
data to be transmitted must be placed in the SIMDR
register. After the data is received from the I2C bus,
the microcontroller can read it from the SIMDR register. Any transmission of data to the I2C bus or reception of data from the I2C bus must be made via the
SIMDR register.
The SIMAR register is the location where the slave
address of the microcontroller is stored. Bits 1~7 of
the SIMAR register define the microcontroller slave
address. Bit 0 is not defined. When a master device,
which is connected to the I2C bus, sends out an address, which matches the slave address in the SIMAR
register, the microcontroller slave device will be selected.
Note that the SIMAR register is the same register as
SIMCON2 which is used by the SPI interface.
The SIMCON0 register is used for the I2C overall
on/off control and to describe if the I2C interface remains active in the Idle Mode.
The I2C bus is a bidirectional 2-line communication interface originally developed by Philips. The possibility of
transmitting and receiving data on only 2 lines offers
many new application possibilities for microcontroller
based applications.
· I2C Interface Operation
As the I2C interface pins are pin-shared with segment
pins and with the SPI function pins, the I2C interface
must first be enabled by selecting the correct configuration option.
There are two lines associated with the I2C bus, the
first is known as SDA and is the Serial Data line, the
second is known as SCL line and is the Serial Clock
line. As many devices may be connected together on
the same bus, their outputs are both open drain types.
For this reason it is necessary that external pull-high
resistors are connected to these outputs. Note that no
chip select line exists, as each device on the I2C bus is
identified by a unique address which will be transmitted and received on the I2C bus.
When two devices communicate with each other on
the bidirectional I2C bus, one is known as the master
device and one as the slave device. Both master and
slave can transmit and receive data, however, it is the
master device that has overall control of the bus. For
this device, which only operates in slave mode, there
are two methods of transferring data on the I2C bus,
the slave transmit mode and the slave receive mode.
b 7
S A 6
b 0
S A 5
S A 4
S A 3
S A 2
S A 1
S A 0
S IM A R
R e g is te r
N o t im p le m e n te d , r e a d a s " 0 "
I2C
d e v ic e s la v e a d d r e s s
Slave Address Register - SIMAR
b 7
S IM 2
b 0
S IM 1
S IM 0
S IM E N
S IM ID L E
S IM C O N 0 R e g is te r
I2 C s ta tu s in Id le m o d e
1 : e n a b le
0 : d is a b le
I2C O n /O ff c o n tro l
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d , r e a d a s " 0 "
I2 C M a s te r /S la v e a n d c lo c k
S IM 2
S IM 1
S IM 0
0
0
0
N o
1
0
0
N o
0
1
0
N o
1
1
0
N o
0
0
1
N o
1
0
1
N o
0
1
1
I2C
1
1
1
N o
c o n tro l
t u s
t u s
t u s
t u s
t u s
t u s
m o
t u s
e d
e d
e d
e d
e d
e d
d e
e d
I2C Control Register - SIMCON0
Rev. 1.40
49
September 8, 2009
HT56R64
b 7
H C F
b 0
H A A S
H B B
H T X
T X A K
S R W
R X A K
S IM C O N 1 R e g is te r
R e c e iv e a c k n o w le d g e fla g
1 : n o t a c k n o w le d g e d
0 : a c k n o w le d g e d
N o t im p le m e n te d , r e a d a s " 0 "
M a s te r d a ta r e a d /w r ite r e q u e s t fla g
1 : re q u e s t d a ta re a d
0 : r e q u e s t d a ta w r ite
T r a n s m it a c k n o w le d g e fla g
1 : d o n 't a c k n o w le d g e
0 : a c k n o w le d g e
T r a n s m it/R e c e iv e m o d e
1 : tr a n s m it m o d e
0 : r e c e iv e m o d e
I2 C b u s b u s fla g
1 : b u s y
0 : n o t b u s y
C a llin g a d d r e s s m a tc h e d fla g
1 : m a tc h e d
0 : n o t m a tc h e d
D a ta tr a n s fe r fla g
1 : tr a n s fe r c o m p le te
0 : tr a n s fe r n o t c o m p le te
I2C Control Register - SIMCON1
The following gives further explanation of each bit:
¨
¨
¨
¨
SIMEN
The SIMEN bit determines if the I2C bus is enabled
or disabled. If data is to be transferred or received
on the I2C bus then this bit must be set high.
SIMIDLE
The SIMIDLE bit is used to select if the I2C interface
continues running when the device is in the IDLE
mode. Setting the bit high allows the I2C interface to
maintain operation when the device is in the Idle
mode. Clearing the bit to zero disables any I2C operations when in the Idle mode.
The SIMCON1 register is used to control and monitor the status of the I2C bus.
The following gives further explanation of each bit:
HTX
The HTX flag is the transmit/receive mode bit. This
flag should be set high to set the transmit mode and
low for the receive mode.
¨
TXAK
The TXAK flag is the transmit acknowledge flag. After the receipt of 8-bits of data, this bit will be transmitted to the bus on the 9th clock. To continue
receiving more data, this bit has to be reset to zero
before further data is received.
¨
SRW
The SRW bit is the Slave Read/Write bit. This bit determines whether the master device wishes to
transmit or receive data from the I2C bus. When the
transmitted address and slave address match, that
is when the HAAS bit is set high, the device will
check the SRW bit to determine whether it should
be in transmit mode or receive mode. If the SRW bit
is high, the master is requesting to read data from
the bus, so the device should be in transmit mode.
When the SRW bit is zero, the master will write data
to the bus, therefore the device should be in receive
mode to read this data.
¨
RXAK
The RXAK flag is the receive acknowledge flag.
When the RXAK bit has been reset to zero it means
that a correct acknowledge signal has been received at the 9th clock, after 8 bits of data have
been transmitted. When in the transmit mode, the
transmitter checks the RXAK bit to determine if the
receiver wishes to receive the next byte. The transmitter will therefore continue sending out data until
the RXAK bit is set to ²1². When this occurs, the
transmitter will release the SDA line to allow the
master to send a STOP signal to release the bus.
HCF
The HCF flag is the data transfer flag. This flag will
be zero when data is being transferred. Upon completion of an 8-bit data transfer the flag will go high
and an interrupt will be generated.
HASS
The HASS flag is the address match flag. This flag
is used to determine if the slave device address is
the same as the master transmit address. If the addresses match then this bit will be high, if there is no
match then the flag will be low.
¨
¨
HBB
The HBB flag is the I2C busy flag. This flag will be
high when the I2C bus is busy which will occur when
a START signal is detected. The flag will be reset to
zero when the bus is free which will occur when a
STOP signal is detected.
Rev. 1.40
50
September 8, 2009
HT56R64
S T A R T s ig n a l
fro m M a s te r
S e n d s la v e a d d r e s s
a n d R /W b it fr o m M a s te r
A c k n o w le d g e
fr o m s la v e
S e n d d a ta b y te
fro m M a s te r
A c k n o w le d g e
fr o m s la v e
S T O P s ig n a l
fro m M a s te r
I2C Bus Communication
· Start Signal
The START signal can only be generated by the master device connected to the I2C bus and not by the
microcontroller, which is only a slave device. This
START signal will be detected by all devices connected to the I2C bus. When detected, this indicates
that the I2C bus is busy and therefore the HBB bit will
be set. A START condition occurs when a high to low
transition on the SDA line takes place when the SCL
line remains high.
2
Communication on the I C bus requires four separate
steps, a START signal, a slave device address transmission, a data transmission and finally a STOP signal.
When a START signal is placed on the I2C bus, all devices on the bus will receive this signal and be notified of
the imminent arrival of data on the bus. The first seven
bits of the data will be the slave address with the first bit
being the MSB. If the address of the microcontroller
matches that of the transmitted address, the HAAS bit in
the SIMCON1 register will be set and an I2C interrupt
will be generated. After entering the interrupt service
routine, the microcontroller slave device must first check
the condition of the HAAS bit to determine whether the
interrupt source originates from an address match or
from the completion of an 8-bit data transfer. During a
data transfer, note that after the 7-bit slave address has
been transmitted, the following bit, which is the 8th bit, is
the read/write bit whose value will be placed in the SRW
bit. This bit will be checked by the microcontroller to determine whether to go into transmit or receive mode. Before any transfer of data to or from the I2C bus, the
microcontroller must initialise the bus, the following are
steps to achieve this:
· Slave Address
The transmission of a START signal by the master will
be detected by all devices on the I2C bus. To determine which slave device the master wishes to communicate with, the address of the slave device will be
sent out immediately following the START signal. All
slave devices, after receiving this 7-bit address data,
will compare it with their own 7-bit slave address. If the
address sent out by the master matches the internal
address of the microcontroller slave device, then an
internal I2C bus interrupt signal will be generated. The
next bit following the address, which is the 8th bit, defines the read/write status and will be saved to the
SRW bit of the SIMCON1 register. The device will
then transmit an acknowledge bit, which is a low level,
as the 9th bit. The microcontroller slave device will
also set the status flag HAAS when the addresses
match.
As an I2C bus interrupt can come from two sources,
when the program enters the interrupt subroutine, the
HAAS bit should be examined to see whether the interrupt source has come from a matching slave address or from the completion of a data byte transfer.
When a slave address is matched, the device must be
placed in either the transmit mode and then write data
to the SIMDR register, or in the receive mode where it
must implement a dummy read from the SIMDR register to release the SCL line.
Step 1
Write the slave address of the microcontroller to the I2C
bus address register SIMAR.
Step 2
Set the SIMEN bit in the SIMCON0 register to ²1² to enable the I2C bus.
Step 3
Set the ESIM bit of the interrupt control register to enable the I2C bus interrupt.
Rev. 1.40
51
September 8, 2009
HT56R64
S C L
S R W
S la v e A d d r e s s
S ta rt
0
1
S D A
1
1
0
1
0
1
D a ta
S C L
1
0
0
1
A C K
0
A C K
0
1
0
S to p
0
S D A
S = S
S A =
S R =
M = S
D = D
A = A
P = S
S
ta rt (1
S la v e
S R W
la v e d
a ta (8
C K (R
to p (1
S A
b it)
A d d r e s s ( 7 b its )
b it ( 1 b it)
e v ic e s e n d a c k n o w le d g e b it ( 1 b it)
b its )
X A K b it fo r tr a n s m itte r , T X A K b it fo r r e c e iv e r 1 b it)
b it)
S R
M
D
A
D
A
S
S A
S R
M
D
A
D
A
P
2
I C Communication Timing Diagram
· SRW Bit
the MSB first and the LSB last. After receipt of 8-bits of
data, the receiver must transmit an acknowledge signal, level ²0², before it can receive the next data byte.
If the transmitter does not receive an acknowledge bit
signal from the receiver, then it will release the SDA
line and the master will send out a STOP signal to release control of the I2C bus. The corresponding data
will be stored in the SIMDR register. If setup as a
transmitter, the microcontroller slave device must first
write the data to be transmitted into the SIMDR register. If setup as a receiver, the microcontroller slave device must read the transmitted data from the SIMDR
register.
The SRW bit in the SIMCON1 register defines
whether the microcontroller slave device wishes to
read data from the I2C bus or write data to the I2C bus.
The microcontroller should examine this bit to determine if it is to be a transmitter or a receiver. If the SRW
bit is set to ²1² then this indicates that the master
wishes to read data from the I2C bus, therefore the
microcontroller slave device must be setup to send
data to the I2C bus as a transmitter. If the SRW bit is
²0² then this indicates that the master wishes to send
data to the I2C bus, therefore the microcontroller slave
device must be setup to read data from the I2C bus as
a receiver.
S C L
· Acknowledge Bit
After the master has transmitted a calling address,
any slave device on the I2C bus, whose own internal
address matches the calling address, must generate
an acknowledge signal. This acknowledge signal will
inform the master that a slave device has accepted its
calling address. If no acknowledge signal is received
by the master then a STOP signal must be transmitted
by the master to end the communication. When the
HAAS bit is high, the addresses have matched and
the microcontroller slave device must check the SRW
bit to determine if it is to be a transmitter or a receiver.
If the SRW bit is high, the microcontroller slave device
should be setup to be a transmitter so the HTX bit in
the SIMCON1 register should be set to ²1² if the SRW
bit is low then the microcontroller slave device should
be setup as a receiver and the HTX bit in the
SIMCON1 register should be set to ²0².
S D A
S ta r t b it
D a ta
s ta b le
D a ta
a llo w
c h a n g e
S to p b it
Data Timing Diagram
· Receive Acknowledge Bit
When the receiver wishes to continue to receive the
next data byte, it must generate an acknowledge bit,
known as TXAK, on the 9th clock. The microcontroller
slave device, which is setup as a transmitter will check
the RXAK bit in the SIMCON1 register to determine if
it is to send another data byte, if not then it will release
the SDA line and await the receipt of a STOP signal
from the master.
· Data Byte
The transmitted data is 8-bits wide and is transmitted
after the slave device has acknowledged receipt of its
slave address. The order of serial bit transmission is
Rev. 1.40
52
September 8, 2009
HT56R64
S ta rt
N o
N o
Y e s
H A A S = 1
?
Y e s
Y e s
H T X = 1
?
N o
S R W = 1
?
R e a d fro m
S IM D R
S E T H T X
C L R H T X
C L R T X A K
R E T I
W r ite to
S IM D R
D u m m y R e a d
F ro m S IM D R
R E T I
R E T I
Y e s
R X A K = 1
?
N o
C L R H T X
C L R T X A K
W r ite to
S IM D R
D u m m y R e a d
fro m S IM D R
R E T I
R E T I
I2C Bus ISR Flow Chart
Peripheral Clock Output
S ta rt
The Peripheral Clock Output allows the device to supply
external hardware with a clock signal synchronised to
the microcontroller clock.
W r ite S la v e
A d d re s s to S IM A R
As the peripheral clock output pin, PINT, is shared with
the LCD segment line SEG14, the required pin function
is chosen via configuration option. The clock source for
the Peripheral Clock Output can originate from either
the Timer/Event Counter 0 divided by two or a divided
ratio of the internal fsys clock. The clock source is selected using the PCKEN bit in the SIMCON0 register.
The required division ratio of the system clock is selected using the PCKPSC0 and PSCPSC1 bits in the
same register. If the system enters the Power down
mode this will also influence the operation of the Peripheral Clock Output as shown in the block diagram.
S E T S IM [2 :0 ]= 1 1 0
S E T S IM E N
D is a b le
I2C B u s
In te rru p t= ?
E n a b le
C L R E H I
P o ll H IF to d e c id e
w h e n to g o to I2C B u s IS R
S E T E H I
W a it fo r In te r r u p t
G o to M a in P r o g r a m
G o to M a in P r o g r a m
I2C Bus Initialisation Flow Chart
Rev. 1.40
53
September 8, 2009
HT56R64
T M R 0 O u tp u t /2
P C K P S C 1
P C K P S C 0
P C K E N
P C K O u tp u t
C lo c k S e le c to r
fS
S le e p
M o d e
Id le M o d e
S IM ID L E
Y S
S P I/I2C
S IM E N
S IM
S IM
[2 :0 ] ¹ 1 1 1
M o d u le S tr u c tu r e
N o te : S le e p M o d e = H A L T & ID L E N = 0
Id le M o d e = H A L T & ID L E N = 1
SPI SIM Module Structure
b 7
S IM 2
b 0
S IM 1
S IM 0
P C K P S C 1 P C K P S C 0 S IM E N
P C K E N
S IM ID L E
S IM C O N 0 R e g is te r
S P I S ta tu s in Id le M o d e
- d e s c r ib e d e ls e w h o s e
P C K C lo c k S e le c t
P C K P S C 1 P C K P S C 0
0
0
0
1
1
0
1
1
fS
C lo c k S o u r c e
Y S
fS Y S /4
fS Y S /8
T im e r /E v n e t C o u n te r 0 ¸ 2
P e r ip h e r a l C lo c k E n a b le
0 : c lo c k d is a b le
1 : c lo c k e n a b le
S P I M a s te r /S la v e a n d C lo c k C o n tr o l
- d e s c r ib e d e ls e w h o s e
Peripheral Clock Output Control - SIMCON0
Buzzer
The buzzer is driven by the internal clock source, fS,
which then passes through a divider, the division ratio of
which is selected by configuration options to provide a
range of buzzer frequencies from fS/22 to fS/29. The
clock source that generates fS, which in turn controls the
buzzer frequency, can originate from three different
sources, the RTC oscillator, the 32K_INT oscillator or
the System oscillator/4, the choice of which is determined by the fS clock source configuration option. Note
that the buzzer frequency is controlled by configuration
options, which select both the source clock for the internal clock fS and the internal division ratio. There are no
internal registers associated with the buzzer frequency.
Operating in a similar way to the Programmable Frequency Divider, the Buzzer function provides a means of
producing a variable frequency output, suitable for applications such as Piezo-buzzer driving or other external
circuits that require a precise frequency generator. The
BZ and BZ pins form a complimentary pair, and are
pin-shared with I/O pins, PA0 and PA1. A configuration
option is used to select from one of three buzzer options.
The first option is for both pins PA0 and PA1 to be used
as normal I/Os, the second option is for both pins to be
configured as BZ and BZ buzzer pins, the third option
selects only the PA0 pin to be used as a BZ buzzer pin
with the PA1 pin retaining its normal I/O pin function.
Note that the BZ pin is the inverse of the BZ pin which together generate a differential output which can supply
more power to connected interfaces such as buzzers.
fS
Y S
/4
fR
T C
3 2 K _ IN T
fS S o u rc e
C o n fig u r a tio n
O p tio n
fS
If the configuration options have selected both pins PA0
and PA1 to function as a BZ and BZ complementary pair
of buzzer outputs, then for correct buzzer operation it is
C o n fig u r a tio n O p tio n
D iv id e b y 2 2 ~ 2 9
B Z
B Z
Buzzer Function
Rev. 1.40
54
September 8, 2009
HT56R64
essential that both pins must be setup as outputs by setting bits PAC0 and PAC1 of the PAC port control register to zero. The PA0 data bit in the PA data register must
also be set high to enable the buzzer outputs, if set low,
both pins PA0 and PA1 will remain low. In this way the
single bit PA0 of the PA register can be used as an
on/off control for both the BZ and BZ buzzer pin outputs.
Note that the PA1 data bit in the PA register has no control over the BZ buzzer pin PA1.
PA0/PA1 Pin Function Control
PAC Register
PAC0
PAC Register
PAC1
PA Data Register
PA0
PA Data Register
PA1
Output
Function
0
0
1
x
PA0=BZ
PA1=BZ
0
0
0
x
PA0=²0²
PA1=²0²
0
1
1
x
PA0=BZ
PA1=input line
0
1
0
x
PA0=²0²
PA1=input line
1
0
x
D
PA0=input line
PA1=D
1
1
x
x
PA0=input line
PA0=input line
²x² stands for don¢t care
²D² stands for Data ²0² or ²1²
Note that no matter what configuration option is chosen
for the buzzer, if the port control register has setup the
pin to function as an input, then this will override the configuration option selection and force the pin to always
behave as an input pin. This arrangement enables the
pin to be used as both a buzzer pin and as an input pin,
so regardless of the configuration option chosen; the actual function of the pin can be changed dynamically by
the application program by programming the appropriate port control register bit.
If configuration options have selected that only the PA0
pin is to function as a BZ buzzer pin, then the PA1 pin
can be used as a normal I/O pin. For the PA0 pin to function as a BZ buzzer pin, PA0 must be setup as an output
by setting bit PAC0 of the PAC port control register to
zero. The PA0 data bit in the PA data register must also
be set high to enable the buzzer output, if set low pin
PA0 will remain low. In this way the PA0 bit can be used
as an on/off control for the BZ buzzer pin PA0. If the
PAC0 bit of the PAC port control register is set high, then
pin PA0 can still be used as an input even though the
configuration option has configured it as a BZ buzzer
output.
In te r n a l C lo c k S o u r c e
P A 0 D a ta
B Z O u tp u t a t P A 0
P A 1 D a ta
B Z O u tp u t a t P A 1
Buzzer Output Pin Control
Note:
The above drawing shows the situation where both pins PA0 and PA1 are selected by configuration option to
be BZ and BZ buzzer pin outputs. The Port Control Register of both pins must have already been setup as output. The data setup on pin PA1 has no effect on the buzzer outputs.
Rev. 1.40
55
September 8, 2009
HT56R64
Interrupts
immediately serviced, the request flag will still be recorded. If an interrupt requires immediate servicing
while the program is already in another interrupt service
routine, the EMI bit should be set after entering the routine, to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the
related interrupt is enabled, until the Stack Pointer is
decremented. If immediate service is desired, the stack
must be prevented from becoming full.
Interrupts are an important part of any microcontroller
system. When an external event or an internal function
such as a Timer/Event Counter or an A/D converter requires microcontroller attention, their corresponding interrupt will enforce a temporary suspension of the main
program allowing the microcontroller to direct attention
to their respective needs. The device contains several
external interrupt and internal interrupts functions. The
external interrupts are controlled by the action of the external INT0, INT1 and PINT pins, while the internal interrupts are controlled by the Timer/Event Counter
overflows, the Time Base interrupt, the RTC interrupt,
the SPI/I2C interrupt and the the A/D converter interrupt.
Interrupt Priority
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In case of simultaneous requests,
the following table shows the priority that is applied.
Interrupt Registers
Overall interrupt control, which means interrupt enabling
and request flag setting, is controlled by the INTC0,
INTC1 and MFIC registers, which are located in the
Data Memory. By controlling the appropriate enable bits
in these registers each individual interrupt can be enabled or disabled. Also when an interrupt occurs, the
corresponding request flag will be set by the
microcontroller. The global enable flag if cleared to zero
will disable all interrupts.
Interrupt Source
External Interrupt 0
Interrupt Operation
A Timer/Event Counter overflow, Time Base, RTC overflow, SPI/I2C data transfer complete, an end of A/D conversion or the external interrupt line being triggered will
all generate an interrupt request by setting their corresponding request flag, if their appropriate interrupt enable bit is set. When this happens, the Program
Counter, which stores the address of the next instruction
to be executed, will be transferred onto the stack. The
Program Counter will then be loaded with a new address which will be the value of the corresponding interrupt vector. The microcontroller will then fetch its next
instruction from this interrupt vector. The instruction at
this vector will usually be a JMP statement which will
jump to another section of program which is known as
the interrupt service routine. Here is located the code to
control the appropriate interrupt. The interrupt service
routine must be terminated with a RETI statement,
which retrieves the original Program Counter address
from the stack and allows the microcontroller to continue
with normal execution at the point where the interrupt
occurred.
Vector
1
04H
External Interrupt 1
2
08H
Timer/Event Counter 0 Overflow
3
0CH
Timer/Event Counter
1 Overflow
4
10H
SPI/I2C Interrupt
5
14H
Multi-function Interrupt
6
18H
The A/D converter interrupt, Real Time clock interrupt,
Time Base interrupt and External Peripheral interrupt all
share the same interrupt vector which is 18H. Each of
these interrupts have their own own individual interrupt
flag but also share the same MFF interrupt flag. The
MFF flag will be cleared by hardware once the
Multi-function interrupt is serviced, however the individual interrupts that have triggered the Multi-function interrupt need to be cleared by the application program.
External Interrupt
For an external interrupt to occur, the global interrupt
enable bit, EMI, and external interrupt enable bits, EEI0
and EEI1, must first be set. Additionally the correct
interrupt edge type must be selected using the
INTEDGE register to enable the external interrupt
function and to choose the trigger edge type. An actual
external interrupt will take place when the external
interrupt request flag, EIF0 or EIF1, is set, a situation
that will occur when a transition, whose type is chosen
by the edge select bit, appears on the INT0 or INT1 pin.
The external interrupt pins are pin-shared with the I/O
pins PD4 and PD5 and can only be configured as
external interrupt pins if their corresponding external
interrupt enable bit in the INTC0 register has been set.
The pin must also be setup as an input by setting the
corresponding PDC.4 and PDC.5 bits in the port control
register. When the interrupt is enabled, the stack is not
full and the correct transition type appears on the
The various interrupt enable bits, together with their associated request flags, are shown in the accompanying
diagram with their order of priority.
Once an interrupt subroutine is serviced, all the other interrupts will be blocked, as the EMI bit will be cleared automatically. This will prevent any further interrupt nesting
from occurring. However, if other interrupt requests occur during this interval, although the interrupt will not be
Rev. 1.40
Priority
56
September 8, 2009
HT56R64
b 7
b 0
T 0 F
E IF 1
E IF 0
E T 0 I E E I1
E E I0
IN T C 0 R e g is te
E M I
M a s te r in te r r u p t g lo b a l e n a b le
1 : g lo b a l e n a b le
0 : g lo b a l d is a b le
E x te r n a l in te r r u p t 0 e n a b le
1 : e n a b le
0 : d is a b le
E x te r n a l in te r r u p t 1 e n a b le
1 : e n a b le
0 : d is a b le
T im e r /E v e n t C o u n te r 0 in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
E x te r n a l in te r r u p t 0 r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
E x te r n a l in te r r u p t 1 r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
T im e r /E v e n t C o u n te r 0 in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
F o r te s t m o d e u s e d o n ly
M u s t b e w r itte n a s " 0 " ; o th e r w is e m a y r e s u lt in u n p r e d ic ta b le o p e
Interrupt Control Register INTC0
b 7
b 0
M F F
S IM F
T 1 F
E M F I E S IM
E T 1 I
IN T C 1 R e g is te r
T im e r /E v e n t C o u n te r 1 in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
S P I/I2 C in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
M u lti- fu n c tio n in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d , r e a d a s " 0 "
T im e r /E v e n t C o u n te r 1 in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
S P I/I2 C in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
M u lti- fu n c tio n in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
N o t im p le m e n te d , r e a d a s " 0 "
Interrupt Control Register INTC1
Rev. 1.40
57
September 8, 2009
HT56R64
b 7
P E F
b 0
T B F
R T F
A D F
E P I
E T B I E R T I E A D I
M F IC
R e g is te r
A /D c o n v e r te r in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
R e a l T im e C lo c k in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
T im e B a s e in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
E x te r n a l p e r ip h e r a l in te r r u p t e n a b le
1 : e n a b le
0 : d is a b le
A /D c o n v e r te r in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
R e a l T im e C lo c k in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
T im e B a s e in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
E x te r n a l p e r ip h e r a l in te r r u p t r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
Interrupt Control Register MFIC
A u to m a tic a lly C le a r e d b y IS R
e x c e p t
fo r T B F , R T F a n d T 2 F
M a n u a lly S e t o r C le a r e d b y S o ftw a r e
A u to m a tic a lly D is a b le d b y IS R
C a n b e E n a b le d M a n u a lly
P r io r ity
E x te rn a l In te rru p t
R e q u e s t F la g E IF 0
E E I0
E x te rn a l In te rru p t
R e q u e s t F la g E IF 1
E E I1
T im e r /E v e n t C o u n te r 0
In te r r u p t R e q u e s t F la g T 0 F
E T 0 I
T im e r /E v e n t C o u n te r 1
In te r r u p t R e q u e s t F la g T 1 F
E T 1 I
S P I/I2C
In te r r u p t R e q u e s t F la g S IM F
E S IM
M u lti- fu n c tio n
In te r r u p t R e q u e s t F la g M F F
E M F I
A /D C o n v e rte r
In te r r u p t R e q u e s t F la g A D F
E A D I
R e a l T im e C lo c k
In te r r u p t R e q u e s t F la g R T F
E R T I
T im e B a s e
In te r r u p t R e q u e s t F la g T B F
E T B I
E x te r n a l P e r ip h e r a l
In te r r u p t R e q u e s t F la g P E F
E P I
E M I
H ig h
In te rru p t
P o llin g
L o w
Interrupt Structure
Rev. 1.40
58
September 8, 2009
HT56R64
external interrupt pin, a subroutine call to the external
interrupt vector at location 04H or 08H, will take place.
When the interrupt is serviced, the external interrupt
request flags, EIF0 or EIF1, will be automatically reset
and the EMI bit will be automatically cleared to disable
other interrupts. Note that any pull-high resistor
selections on this pin will remain valid even if the pin is
used as an external interrupt input.
For an external peripheral interrupt to occur, the global
interrupt enable bit, EMI, external peripheral interrupt
enable bit, EPI, and Multi-function interrupt enable bit,
EMFI, must first be set. An actual external peripheral interrupt will take place when the external interrupt request flag, PEF, is set, a situation that will occur when a
negative transition, appears on the PINT pin. The external peripheral interrupt pin is pin-shared with the segment pin SEG15, and is configured as a peripheral
interrupt pin via a configuration option. When the interrupt is enabled, the stack is not full and a negative transition type appears on the external peripheral interrupt
pin, a subroutine call to the Multi-function interrupt vector at location18H, will take place. When the external
peripheral interrupt is serviced, the EMI bit will be
cleared to disable other interrupts, however only the
MFF interrupt request flag will be reset. As the PEF flag
will not be automatically reset, it has to be cleared by the
application program.
The INTEDGE register is used to select the type of active
edge that will trigger the external interrupt. A choice of either rising and falling edge types can be chosen along
with an option to allow both edge types to trigger an external interrupt. Note that the INTEDGE register can also be
used to disable the external interrupt function.
F ilte r O n /O ff
C o n fig u r a tio n O p tio n
M C U
IN T C 0
F ilte r
E x te rn a l IN T .0
IN T C 1
F ilte r
E x te rn a l IN T .1
Timer/Event Counter Interrupt
For a Timer/Event Counter interrupt to occur, the global
interrupt enable bit, EMI, and the corresponding timer
interrupt enable bit, ET0I or ET1I, must first be set. An
actual Timer/Event Counter interrupt will take place
when the Timer/Event Counter request flag, T0F or T1F,
is set, a situation that will occur when the Timer/Event
Counter overflows. When the interrupt is enabled, the
stack is not full and a Timer/Event Counter overflow occurs, a subroutine call to the timer interrupt vector at location 0CH or 10C, will take place. When the interrupt is
serviced, the timer interrupt request flag, T0F or T1F, will
be automatically reset and the EMI bit will be automatically cleared to disable other interrupts.
The external interrupt pins are connected to an internal
filter to reduce the possibility of unwanted external interrupts due to adverse noise or spikes on the external interrupt input signal. As this internal filter circuit will
consume a limited amount of power, a configuration option is provided to switch off the filter function, an option
which may be beneficial in power sensitive applications,
but in which the integrity of the input signal is high. Care
must be taken when using the filter on/off configuration
option as it will be applied not only to both the external
interrupt pins but also to the Timer/Event Counter external input pins. Individual external interrupt or
Timer/Event Counter pins cannot be selected to have a
filter on/off function.
A/D Interrupt
The A/D Interrupt is contained within the Multi-function
Interrupt.
External Peripheral Interrupt
The External Peripheral Interrupt operates in a similar
way to the external interrupt and is contained within the
Multi-function interrupt.
For an A/D Interrupt to be generated, the global interrupt
enable bit, EMI, A/D Interrupt enable bit, EADI, and
Multi-function interrupt enable bit, EMFI, must first be
b 7
b 0
IN T 1 S 1 IN T 1 S 0 IN T 0 S 1 IN T 0 S 0
IN T E D G E R e g is te r
IN T 0 E d g e S e
IN T 0 S 1
IN
0
0
1
1
le c t
T 0 S 0
0
1
0
1
d is a b le
r is in g e d g e tr ig g e r
fa llin g e d g e tr ig g e r
d u a l e d g e tr ig g e r
IN T 1 E D g e S e le c t
IN T 1 S 1
IN T 1 S 0
0
0
1
0
0
1
1
1
d is a b le
r is in g e d g e tr ig g e r
fa llin g e d g e tr ig g e r
d u a l e d g e tr ig g e r
N o t im p le m e n te d , r e a d a s " 0 "
Interrupt Active Edge Register - INTEDGE
Rev. 1.40
59
September 8, 2009
HT56R64
set. An actual A/D Interrupt will take place when the A/D
Interrupt request flag, ADF, is set, a situation that will occur when the A/D conversion process has finished.
When the interrupt is enabled, the stack is not full and
the A/D conversion process has ended, a subroutine
call to the Multi-function interrupt vector at location18H,
will take place. When the A/D Interrupt is serviced, the
EMI bit will be cleared to disable other interrupts, however only the MFF interrupt request flag will be reset. As
the ADF flag will not be automatically reset, it has to be
cleared by the application program.
bit will be automatically cleared to disable other interrupts. However, it must be noted that the request flags
from the original source of the Multi-function interrupt,
namely the Time-Base interrupt, Real Time Clock interrupt, A/D Converter interrupt or External Peripheral interrupt will not be automatically reset and must be manually
reset by the application program.
SPI/I2C Interface Interrupt
For a Real Time Clock interrupt to be generated, the
global interrupt enable bit, EMI, Real Time Clock interrupt enable bit, ERTI, and Multi-function interrupt enable
bit, EMFI, must first be set. An actual Real Time Clock
interrupt will take place when the Real Time Clock request flag, RTF, is set, a situation that will occur when
the Real Time Clock overflows. When the interrupt is enabled, the stack is not full and the Real Time Clock overflows, a subroutine call to the Multi-function interrupt
vector at location18H, will take place. When the Real
Time Clock interrupt is serviced, the EMI bit will be
cleared to disable other interrupts, however only the
MFF interrupt request flag will be reset. As the RTF flag
will not be automatically reset, it has to be cleared by the
application program.
Real Time Clock Interrupt
The Real Time Clock Interrupt is contained within the
Multi-function Interrupt.
For an SPI/I2C interrupt to occur, the global interrupt enable bit, EMI, and the corresponding interrupt enable bit,
ESIM must be first set. An actual SPI/I2C interrupt will
take place when the SPI/I2C interface request flag,
SIMF, is set, a situation that will occur when a byte of
data has been transmitted or received by the SPI/I2C interface When the interrupt is enabled, the stack is not
full and a byte of data has been transmitted or received
by the SPI/I2C interface, a subroutine call to the SPI/I2C
interrupt vector at location 14H, will take place. When
the interrupt is serviced, the SPI/I2C request flag, SIMF
will be automatically reset and the EMI bit will be automatically cleared to disable other interrupts.
Similar in operation to the Time Base interrupt, the purpose of the RTC interrupt is also to provide an interrupt
signal at fixed time periods. The RTC interrupt clock
source originates from the internal clock source fS. This
fS input clock first passes through a divider, the division
ratio of which is selected by programming the appropriate bits in the RTCC register to obtain longer RTC interrupt periods whose value ranges from 28/fS~215/fS. The
clock source that generates fS, which in turn controls the
RTC interrupt period, can originate from three different
sources, the RTC oscillator, 32K_INT oscillator or the
System oscillator/4, the choice of which is determine by
the fS clock source configuration option.
Multi-function Interrupt
An additional interrupt known as the Multi-function interrupt is provided. Unlike the other interrupts, this interrupt
has no independent source, but rather is formed from
four other existing interrupt sources, namely the A/D
Converter interrupt, Time Base interrupt, Real Time
Clock interrupt and the External Peripheral interrupt.
For a Multi-function interrupt to occur, the global interrupt
enable bit, EMI, and the Multi-function interrupt enable
bit, EMFI, must first be set. An actual Multi-function interrupt will take place when the Multi-function interrupt request flag, MFF, is set. This will occur when either a Time
Base overflow, a Real Time Clock overflow, an A/D conversion completion or an External Peripheral Interrupt is
generated. When the interrupt is enabled and the stack is
not full, and either one of the interrupts contained within
the Multi-function interrupt occurs, a subroutine call to the
Multi-function interrupt vector at location 018H will take
place. When the interrupt is serviced, the Multi-Function
request flag, MFF, will be automatically reset and the EMI
fS
Y S
/4
fR
T C
3 2 K _ IN T
fS S o u rc e
C o n fig u r a tio n
O p tio n
fS
Note that the RTC interrupt period is controlled by both
configuration options and an internal register RTCC. A
configuration option selects the source clock for the internal clock fS, and the RTCC register bits RT2, RT1 and
RT0 select the division ratio. Note that the actual division ratio can be programmed from 28 to 215.
D iv id e b y 2 8 ~ 2
(S e t b y R T C C
R e g is te r s )
R T 2
R T 1
1 5
R T C In te rru p t
2 12/fS ~ 2 15/fS
R T 0
RTC Interrupt
Rev. 1.40
60
September 8, 2009
HT56R64
b 7
L V D O
Q O S C
L V D C
R T 2
R T 1
b 0
R T 0
R T C C
R T C
R T 2
0
0
0
0
1
1
1
1
R e g is te r
In te r r u p t P e r io d
R T 0
R T 1
0
0
1
0
0
1
1
1
0
0
1
0
0
1
1
1
P e
2 8
2 9
2 1
2 1
2 1
2 1
2 1
2 1
r io d
/fS
/fS
0
/fS
1
/fS
2
/fS
3
/fS
4
/fS
5
/fS
L o w V o lta g e D e te c to r C o n tr o l
1 : e n a b le
0 : d is a b le
R T C O s c illa to r Q u ic k - s ta r t
1 : d is a b le
0 : e n a b le
L o w V o lta g e D e te c to r O u tp u t
1 : lo w v o lta g e d e te c te d
0 : n o r m a l v o lta g e
N o t im p le m e n te d , r e a d a s " 0 "
Real Time Clock Control Register - RTCC
Time Base Interrupt
source configuration option.
The Time Base Interrupt is contained within the
Multi-function Interrupt.
Essentially operating as a programmable timer, when
the Time Base overflows it will set a Time Base interrupt
flag which will in turn generate an Interrupt request via
the Multi-function Interrupt vector.
For a Time Base Interrupt to be generated, the global interrupt enable bit, EMI,Time Base Interrupt enable bit,
ETBI, and Multi-function interrupt enable bit, EMFI,
must first be set. An actual Time Base Interrupt will take
place when the Time Base Interrupt request flag, TBF, is
set, a situation that will occur when the Time Base overflows. When the interrupt is enabled, the stack is not full
and the Time Base overflows, a subroutine call to the
Multi-function interrupt vector at location18H, will take
place. When the Time Base Interrupt is serviced, the
EMI bit will be cleared to disable other interrupts, however only the MFF interrupt request flag will be reset. As
the TBF flag will not be automatically reset, it has to be
cleared by the application program.
Programming Considerations
By disabling the interrupt enable bits, a requested interrupt can be prevented from being serviced, however,
once an interrupt request flag is set, it will remain in this
condition in the INTC0, INTC1 and MFIC registers until
the corresponding interrupt is serviced or until the request flag is cleared by the application program.
It is recommended that programs do not use the ²CALL
subroutine² instruction within the interrupt subroutine.
Interrupts often occur in an unpredictable manner or
need to be serviced immediately in some applications. If
only one stack is left and the interrupt is not well controlled, the original control sequence will be damaged
once a ²CALL subroutine² is executed in the interrupt
subroutine.
The purpose of the Time Base function is to provide an
interrupt signal at fixed time periods. The Time Base interrupt clock source originates from the Time Base interrupt clock source originates from the internal clock
source fS. This fS input clock first passes through a divider, the division ratio of which is selected by configuration options to provide longer Time Base interrupt
periods. The Time Base interrupt time-out period ranges
from 212/fS~215/fS. The clock source that generates fS,
which in turn controls the Time Base interrupt period,
can originate from three different sources, the RTC oscillator, the 32K_INT internal oscillator or the System oscillator/4, the choice of which is determine by the fS clock
fS
Y S
/4
fR
T C
3 2 K _ IN T
fS S o u rc e
C o n fig u r a tio n
O p tio n
fS
All of these interrupts have the capability of waking up
the processor when in the Power Down Mode.
Only the Program Counter is pushed onto the stack. If
the contents of the status or other registers are altered
by the interrupt service program, which may corrupt the
desired control sequence, then the contents should be
saved in advance.
C o n fig u r a tio n O p tio n
D iv id e b y 2 1 2 ~ 2 1 5
T im e B a s e In te r r u p t
2 12/fS ~ 2 15/fS
Time Base Interrupt
Rev. 1.40
61
September 8, 2009
HT56R64
Reset and Initialisation
proper reset operation. For this reason it is recommended that an external RC network is connected to
the RES pin, whose additional time delay will ensure
that the RES pin remains low for an extended period
to allow the power supply to stabilise. During this time
delay, normal operation of the microcontroller will be
inhibited. After the RES line reaches a certain voltage
value, the reset delay time tRSTD is invoked to provide
an extra delay time after which the microcontroller will
begin normal operation. The abbreviation SST in the
figures stands for System Start-up Timer.
A reset function is a fundamental part of any
microcontroller ensuring that the device can be set to
some predetermined condition irrespective of outside
parameters. The most important reset condition is after
power is first applied to the microcontroller. In this case,
internal circuitry will ensure that the microcontroller, after a short delay, will be in a well defined state and ready
to execute the first program instruction. After this
power-on reset, certain important internal registers will
be set to defined states before the program commences. One of these registers is the Program Counter,
which will be reset to zero forcing the microcontroller to
begin program execution from the lowest Program
Memory address.
V D D
0 .9 V
R E S
tR
S T D
S S T T im e - o u t
In addition to the power-on reset, situations may arise
where it is necessary to forcefully apply a reset condition
when the microcontroller is running. One example of this
is where after power has been applied and the
microcontroller is already running, the RES line is forcefully pulled low. In such a case, known as a normal operation reset, some of the microcontroller registers remain
unchanged allowing the microcontroller to proceed with
normal operation after the reset line is allowed to return
high. Another type of reset is when the Watchdog Timer
overflows and resets the microcontroller. All types of reset operations result in different register conditions being setup.
C h ip R e s e t
Power-On Reset Timing Chart
For most applications a resistor connected between
VDD and the RES pin and a capacitor connected between VSS and the RES pin will provide a suitable external reset circuit. Any wiring connected to the RES
pin should be kept as short as possible to minimise
any stray noise interference.
For applications that operate within an environment
where more noise is present the Enhanced Reset Circuit shown is recommended.
V
Another reset exists in the form of a Low Voltage Reset,
LVR, where a full reset, similar to the RES reset is implemented in situations where the power supply voltage
falls below a certain threshold.
D D
0 .0 1 m F * *
1 N 4 1 4 8 *
There are five ways in which a microcontroller reset can
occur, through events occurring both internally and externally:
V D D
1 0 k W ~
1 0 0 k W
Reset Functions
R E S
3 0 0 W *
0 .1 ~ 1 m F
V S S
· Power-on Reset
The most fundamental and unavoidable reset is the
one that occurs after power is first applied to the
microcontroller. As well as ensuring that the Program
Memory begins execution from the first memory address, a power-on reset also ensures that certain
other registers are preset to known conditions. All the
I/O port and port control registers will power up in a
high condition ensuring that all pins will be first set to
inputs.
Although the microcontroller has an internal RC reset
function, if the VDD power supply rise time is not fast
enough or does not stabilise quickly at power-on, the
internal reset function may be incapable of providing
Rev. 1.40
D D
Note:
²*² It is recommended that this component is
added for added ESD protection
²**² It is recommended that this component is
added in environments where power line noise
is significant
External RES Circuit
More information regarding external reset circuits is
located in Application Note HA0075E on the Holtek
website.
62
September 8, 2009
HT56R64
· RES Pin Reset
· Watchdog Time-out Reset during Power Down
This type of reset occurs when the microcontroller is
already running and the RES pin is forcefully pulled
low by external hardware such as an external switch.
In this case as in the case of other reset, the Program
Counter will reset to zero and program execution initiated from this point.
R E S
0 .4 V
0 .9 V
The Watchdog time-out Reset during Power Down is
a little different from other kinds of reset. Most of the
conditions remain unchanged except that the Program Counter and the Stack Pointer will be cleared to
²0² and the TO flag will be set to ²1². Refer to the A.C.
Characteristics for tSST details.
D D
W D T T im e - o u t
D D
tR
tS
S T D
S T
S S T T im e - o u t
S S T T im e - o u t
WDT Time-out Reset during Power Down
Timing Chart
C h ip R e s e t
RES Reset Timing Chart
Reset Initial Conditions
· Low Voltage Reset - LVR
The different types of reset described affect the reset
flags in different ways. These flags, known as PDF and
TO are located in the status register and are controlled
by various microcontroller operations, such as the
Power Down function or Watchdog Timer. The reset
flags are shown in the table:
The microcontroller contains a low voltage reset circuit
in order to monitor the supply voltage of the device,
which is selected via a configuration option. If the supply
voltage of the device drops to within a range of
0.9V~VLVR such as might occur when changing the battery, the LVR will automatically reset the device internally. The LVR includes the following specifications: For
a valid LVR signal, a low voltage, i.e., a voltage in the
range between 0.9V~VLVR must exist for greater than the
value tLVR specified in the A.C. characteristics. If the low
voltage state does not exceed 1ms, the LVR will ignore it
and will not perform a reset function.
TO PDF
L V R
tR
S T D
S S T T im e - o u t
RESET Conditions
0
0
RES reset during power-on
u
u
RES or LVR reset during normal operation
1
u
WDT time-out reset during normal operation
1
1
WDT time-out reset during Power Down
Note: ²u² stands for unchanged
C h ip R e s e t
The following table indicates the way in which the various components of the microcontroller are affected after
a power-on reset occurs.
Low Voltage Reset Timing Chart
· Watchdog Time-out Reset during Normal Operation
Item
The Watchdog time-out Reset during normal operation is the same as a hardware RES pin reset except
that the Watchdog time-out flag TO will be set to ²1².
Program Counter
Reset to zero
Interrupts
All interrupts will be disabled
WDT
Clear after reset, WDT begins
counting
W D T T im e - o u t
tR
S T D
S S T T im e - o u t
Timer/Event Counter Timer Counter will be turned off
C h ip R e s e t
WDT Time-out Reset during Normal Operation
Timing Chart
Rev. 1.40
Condition After RESET
63
Prescaler
The Timer Counter Prescaler
will be cleared
Input/Output Ports
I/O ports will be setup as inputs
Stack Pointer
Stack Pointer will point to the
top of the stack
September 8, 2009
HT56R64
The different kinds of resets all affect the internal registers of the microcontroller in different ways. To ensure reliable
continuation of normal program execution after a reset occurs, it is important to know what condition the microcontroller
is in after a particular reset occurs. The following table describes how each type of reset affects each of the
microcontroller internal registers. Note that where more than one package type exists the table will reflect the situation
for the larger package type.
Reset
(Power-on)
RES Reset
(Normal Operation)
WDT Time-out
(Normal Operation)
WDT Time-out
(HALT)
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
BP
---- ---0
---- ---0
---- ---0
---- ---u
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
PCL
0000 0000
0000 0000
0000 0000
0000 0000
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
RTCC
--00 0111
--00 0111
--00 0111
--uu uuuu
STATUS
--00 xxxx
--uu uuuu
--1u uuuu
--11 uuuu
INTC0
0000 0000
0000 0000
0000 0000
uuuu uuuu
TMR0
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR0C
00-0 1000
00-0 1000
00-0 1000
uu-u uuuu
TMR1H
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1L
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1C
0000 1---
0000 1---
0000 1---
uuuu u---
PA
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
1111 1111
1111 1111
1111 1111
uuuu uuuu
PBC
1111 1111
1111 1111
1111 1111
uuuu uuuu
PD
1111 1111
1111 1111
1111 1111
uuuu uuuu
PDC
1111 1111
1111 1111
1111 1111
uuuu uuuu
PWM0L
0000 ---0
0000 ---0
0000 ---0
uuuu ---u
PWM0H
0000 0000
0000 0000
0000 0000
uuuu uuuu
PWM1L
0000 ---0
0000 ---0
0000 ---0
uuuu ---u
PWM1H
0000 0000
0000 0000
0000 0000
uuuu uuuu
INTC1
-000 --00
-000 --00
-000 --00
-uuu --uu
TBHP
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
Register
PWM2L
0000 ---0
0000 ---0
0000 ---0
uuuu ---u
PWM2H
0000 0000
0000 0000
0000 0000
uuuu uuuu
PWM3L
0000 ---0
0000 ---0
0000 ---0
uuuu ---u
PWM3H
0000 0000
0000 0000
0000 0000
uuuu uuuu
ADRL
xxxx ----
xxxx ----
xxxx ----
uuuu ----
ADRH
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
ADCR
0100 0000
0100 0000
0100 0000
uuuu uuuu
ACSR
10--
10--
10--
uu--
Rev. 1.40
-000
-000
64
-000
-uuu
September 8, 2009
HT56R64
Reset
(Power-on)
RES Reset
(Normal Operation)
WDT Time-out
(Normal Operation)
WDT Time-out
(HALT)
CLKMOD
000- 0011
000- 0011
000- 0011
uuuu -uuu
PAWU
0000 0000
0000 0000
0000 0000
uuuu uuuu
PAPU
0000 0000
0000 0000
0000 0000
uuuu uuuu
PBPU
0000 0000
0000 0000
0000 0000
uuuu uuuu
PDPU
0000 0000
0000 0000
0000 0000
uuuu uuuu
Register
INTEDGE
---- 0000
---- 0000
---- 0000
---- uuuu
LCDCTRL
0000 0000
0000 0000
0000 0000
uuuu uuuu
LCDOUT1
---- --00
---- --00
---- --00
---- --uu
LCDOUT2
0000 0000
0000 0000
0000 0000
uuuu uuuu
MISC
0000 1010
0000 1010
0000 1010
uuuu uuuu
MFIC
0000 0000
0000 0000
0000 0000
uuuu uuuu
SIMCON0
1110 0000
1110 0000
1110 0000
uuuu uuuu
SIMCON1
1000 00-1
1000 00-1
1000 00-1
uuuu uu-u
SIMDR
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
SIMAR/SIMCON2
0000 0000
0000 0000
0000 0000
uuuu uuuu
Note:
²u² stands for unchanged
²x² stands for unknown
²-² stands for unimplemented
Oscillator
tion, without requiring external capacitors. However, for
some crystal types and frequencies, to ensure oscillation, it may be necessary to add two small value capacitors, C1 and C2. Using a ceramic resonator will usually
require two small value capacitors, C1 and C2, to be
connected as shown for oscillation to occur. The values
of C1 and C2 should be selected in consultation with the
crystal or resonator manufacturer¢s specification. In
most applications, resistor RP1 is not required, however
for those applications where the LVR function is not
used, RP1 may be necessary to ensure the oscillator
stops running when VDD falls below its operating range.
The internal oscillator circuit contains a filter circuit to reduce the possibility of erratic operation due to noise on
the oscillator pins.
Various oscillator options offer the user a wide range of
functions according to their various application requirements. Five types of system clocks can be selected
while various clock source options for the Watchdog
Timer are provided for maximum flexibility. All oscillator
options are selected through the configuration options.
System Clock Configurations
There are five methods of generating the system clock,
two high oscillators, two low oscillators and an externally
supplied clock. The two high oscillators are the external
crystal/ceramic oscillator and the external RC network.
The two low oscillators are the fully integrated 32K_INT
oscillator and the external RTC oscillator. Selecting
whether the low or high oscillator is used as the system
oscillator is implemented using the HLCLK bit in the
CLKMOD register. The source clock for the high and low
oscillators is chosen via configuration options. The frequency of the slow oscillator is also determined using
the SLOWC0~SLOWC2 bits in the CLKMOD register.
C 1
O S C 1
R
O S C 2
C 2
System Crystal/Ceramic Oscillator
Crystal/Ceramic Oscillator
After selecting the correct oscillator configuration option, for most crystal oscillator configurations, the simple
connection of a crystal across OSC1 and OSC2 will create the necessary phase shift and feedback for oscilla-
Rev. 1.40
P 1
More information regarding the oscillator is located in
Application Note HA0075E on the Holtek website.
65
September 8, 2009
HT56R64
Crystal Oscillator C1 and C2 Values
Crystal/Resonator Frequency
C1
C2
12MHz Crystal
¾
¾
8MHz Crystal
¾
¾
4MHz Crystal
¾
¾
1MHz Crystal
¾
¾
10pF
10pF
455kHz Resonator (see Note 2)
Note:
ning RC oscillator with a typical period of 31.2ms at 5V,
requiring no external components. It is selected via configuration option. When the device enters the Power
Down Mode, the system clock will stop running, however the 32K_INT oscillator will continue to run if selected to keep various internal functions operational.
In te rn a l
3 2 K _ IN T
fR
C 3 2 K
1. C1 and C2 values are for guidance only.
2. XTAL mode configuration option: 455kHz.
Internal 32K_INT Oscillator
Crystal Recommended Capacitor Values
External System RC Oscillator
External RTC Oscillator
After selecting the correct configuration option, using
the external system RC oscillator requires that a resistor, with a value between 47kW and 1.5MW, is connected between OSC1 and VDD, and a 470pF capacitor
is connected to ground. Although this is a cost effective
oscillator configuration, the oscillation frequency can
vary with VDD, temperature and process variations and
is therefore not suitable for applications where timing is
critical or where accurate oscillator frequencies are required. For the value of the external resistor ROSC refer
to the Appendix section for typical RC Oscillator vs.
Temperature and VDD characteristics graphics.
With a function similar to the internal 32K-INT 32KHz oscillator, that is to keep some device functions operational during power down, this device also has an
external RTC oscillator. This oscillator also remains active at all times, even when the microcontroller is in the
Power-down mode. This clock source has a fixed frequency of 32768Hz and requires a 32768Hz crystal to
be connected between pins OSC3 and OSC4.
V
C 3
R
3 2 7 6 8 H z
O S C 3
fR
P 2
T C
O S C 4
C 4
D D
External RTC Oscillator
R
O S C
The external resistor and capacitor components connected to the 32768Hz crystal are not necessary to provide oscillation. For applications where precise RTC
frequencies are essential, these components may be
required to provide frequency compensation due to different crystal manufacturing tolerances.
O S C 1
4 7 0 p F
fS
Y S
/4 N M O S O p e n D r a in
O S C 2
RC Oscillator
A configuration option selects whether the external RTC
oscillator or the internal 32K_INT oscillator is selected. Selecting the external RTC oscillator for use as a system oscillator is implmented using bits in the CLKMOD register.
Note that an internal capacitor together with the external
resistor, ROSC, are the components which determine the
frequency of the oscillator. The external capacitor
shown on the diagram does not influence the frequency
of oscillation. This external capacitor should be added to
improve oscillator stability if the open-drain OSC2 output is utilised in the application circuit. The internal oscillator circuit contains a filter circuit to reduce the
possibility of erratic operation due to noise on the oscillator pins.
During power-up there is a time delay associated with
the RTC oscillator waiting for it to start-up. To minimise
this time delay, bit 4 of the RTCC register, known as the
QOSC bit, is provided to have a quick start-up function.
During a power-up condition, this bit will be cleared to
zero which will initiate the RTC oscillator quick start-up
function. However, as there is additional power consumption associated with this quick start-up function, to
reduce power consumption after start-up takes place, it
is recommended that the application program should
set the QOSC bit high for about 2 seconds after
power-on. It should be noted that, no matter what condition the QOSC bit is set to, the RTC oscillator will always
function normally, only there is more power consumption associated with the quick start-up function.
Internal 32K_INT Oscillator
When microcontrollers enter a power down condition,
their internal clocks are normally switched off to stop
microcontroller activity and to conserve power. However, in many microcontroller applications it may be necessary to keep some internal functions operational,
such as timers, even when the microcontroller is in the
Power-down mode. To do this, the device has a
32K_INT oscillator, which is a fully integrated free runRev. 1.40
66
September 8, 2009
HT56R64
b 7
b 0
S L O W C 2 S L O W C 1 S L O W C 0
L T O
H T O
ID L E N
H L C L K
C L K M O D
R e g is te r
fS Y S s e le c t
1 : fM
0 : fS L O W
Id le m o d e
1 : e n a b le
0 : d is a b le
H ig h o s c illa to r r e a d y fla g
1 : tim e - o u t
0 : n o n - tim e - o u t
L o w o s c illa to r r e a d y fla g
1 : tim e - o u t
0 : n o n - tim e - o u t
N o t im p le m e n te d , r e a d a s " 0 "
fS L O W s e le c tio n
S L O W W C 2 S L O W W C 1
0
0
0
0
1
0
1
0
0
1
0
1
1
1
1
1
S L O W W C 0
0
1
0
1
0
1
0
1
fS
L O W
fS
fM
fM
fM
fM
fM
fM
fS
L
L
/6 4
/3 2
/1 6
/8
/4
/2
Clock Control Register - CLKMOD
and can be either the external RTC oscillator or the internal 32K_INT oscillator.
32768Hz Oscillator C1 and C2 Values
Crystal Frequency
C3
C4
32768Hz
8pF
10pF
Note:
The actual frequency of the slow system clock, fSLOW, is
also determined using the SLOWC0~SLOWC2 bits in
the CLKMOD register.
1. C3 and C4 values are for guidance only.
2. RP2=5M~10MW is recommended.
The LCD clock source is provided by fLCD which is fSUB
divided by 8, giving a frequency of 4kHz.
32768 Hz Crystal Recommended Capacitor Values
The fS clock is an internal clock source for the Buzzer,
the RTC oscillator interrupt, the Time Base interrupt and
the Watchdg Timer. The source clock for fS is selected
from one of the oscillators, fSUB or fSYS/4, using a configuration option.
External Oscillator
The system clock can also be supplied by an externally
supplied clock giving users a method of synchronising
their external hardware to the microcontroller operation.
This is selected using a configuration option and supplying the clock on pin OSC1. Pin OSC2 should be left
floating if the external oscillator is used. The internal oscillator circuit contains a filter circuit to reduce the possibility of erratic operation due to noise on the oscillator
pin, however as the filter circuit consumes a certain
amount of power, a configuration option exists to turn
this filter off. Not using the internal filter should be considered in power sensitive applications and where the
externally supplied clock is of a high integrity and supplied by a low impedance source.
The Dual Clock Mode can operate in four states as follows:
· Normal mode: fM on, fSLOW on, fSYS=fM, CPU on, fS
on, fLCD on/off (using the LCDEN bit), fWDT on/off (using a configuration option or WDT control register).
· Slow mode0: fM off, fSLOW=32K_INT oscillator or
RTC oscillator, fSYS=fSLOW, CPU on, fS on, fLCD on/off
(using the LCDEN bit), fWDT on/off (using a configuration option or WDT control register).
· Slow mode1: fM on, fSLOW=fM/2~fM/64, fSYS=fSLOW,
CPU on, fS on, fLCD on/off (using the LCDEN bit), fWDT
on/off (using a configuration option or WDT control
register).
Dual Clock Mode
The device has a dural clock mode for system clock operation, one is known as the high oscillator and the other
as the low oscillator. The High system clock source fM is
selected using a configuration option and can be either
an external crystal or external RC oscillator.
· Idle mode: fM, fSLOW, fSYS off, CPU off; fSUB on, fS
on/off (by selecting fSUB or fSYS/4), fLCD on/off (using
the LCDEN bit), fWDT on/off (using a configuration option or WDT control register).
· Sleep mode: fM, fSLOW, fSYS, fS, fLCD off, CPU off; fSUB,
fWDT on/off (using a configuration option or WDT control register).
The low oscillator clock source, also known as the
Sub-clock, fSUB, is selected also by configuration option
Rev. 1.40
67
September 8, 2009
HT56R64
N o rm a l M o d e
= 0
N "
L E
D
"I
&
L T
H A
fR
T C
fM O ff,
o r fR C 3 2 K O n * ,
fS Y S = O ff
H A
L T
w a
ke
-u
&
"ID
fM O n ,
o r fR C 3 2
fS Y S = fM
S e t "H L C L K "
S le e p M o d e
T C
L E
N "
=
p
S lo w
0
O n ,
K
H A
L T
&
"ID
w a
ke
-u
L E
N "
=
p
1
Id le M o d e
R e s e t "H L C L K "
fR
-u p
k e
w a
fR
-u p
k e
w a
M o d e
&
L T
H A
fM O n /O ff,
fR T C o r fR C 3 2 K O n ,
fS Y S = fM /2 ~ fM /6 4
o r fR T C o r fR C 3 2 K
* D e p e n d in g o n W D T e n a b le /d is a b le c o n d itio n .
# E ith e r f
R T C
o r f
T C
fM O ff,
o r fR C 3 2 K O n # ,
fS Y S = O ff
1
" =
E N
L
"ID
b e o n .
R C 3 2 K
Dual Clock Mode Operation
H ig h O s c illa to r
O S C 1
O S C 1
O S C 2
O S C 1
O S C 2
E x te rn a l
C lo c k
E x te r n a l C lo c k F ilte r O ff
C o n fig u r a tio n O p tio n
E x te rn a l
R C
E x te r n a l/X T A L /R C
C o n fig u r a tio n O p tio n
E x te rn a l
X T A L
fM
M U X
F ilte r
H L C L K B it
fM
fS
O S C 4
In te rn a l
3 2 K _ IN T
L o w
O s c illa to r
T C
M U X
fR
C 3 2 K
fS
U B
fS
Y S
M U X
/4
C o n fig u r a tio n
O p tio n
fM /2 , ... fM /6 4 , fS
S L O W C 0
fR
R T C
3 2 7 6 8 H z
S L O W C 1
S L O W C 2
O S C 3
fS
S lo w
C lo c k
C o n tro l
L
fS
M U X
fS
Y S
fS
U B
fS
/4
Y S
L O W
L
M U X
T im e r 1
T 1 S
R T C in te r r u p t,
T im e B a s e in te r r u p t,
B u z z e r, W D T
fS C lo c k S e le c t
C o n fig u r a tio n O p tio n
fS
U B
¸ 8
fL
= fS
C D
U B
/8
L C D
Dual Clock Mode Structure
Rev. 1.40
68
September 8, 2009
HT56R64
Power Down Mode and Wake-up
quired if the configuration options have enabled the
Watchdog Timer internal oscillator.
Power Down Mode
All of the Holtek microcontrollers have the ability to enter
a Power Down Mode. When the device enters this
mode, the normal operating current, will be reduced to
an extremely low standby current level. This occurs because when the device enters the Power Down Mode,
the system oscillator is stopped which reduces the
power consumption to extremely low levels, however,
as the device maintains its present internal condition, it
can be woken up at a later stage and continue running,
without requiring a full reset. This feature is extremely
important in application areas where the MCU must
have its power supply constantly maintained to keep the
device in a known condition but where the power supply
capacity is limited such as in battery applications.
Wake-up
After the system enters the Power Down Mode, it can be
woken up from one of various sources listed as follows:
· An external reset
· An external falling edge on Port A
· A system interrupt
· A WDT overflow
If the system is woken up by an external reset, the device will experience a full system reset, however, if the
device is woken up by a WDT overflow, a Watchdog
Timer reset will be initiated. Although both of these
wake-up methods will initiate a reset operation, the actual source of the wake-up can be determined by examining the TO and PDF flags. The PDF flag is cleared by a
system power-up or executing the clear Watchdog
Timer instructions and is set when executing the ²HALT²
instruction. The TO flag is set if a WDT time-out occurs,
and causes a wake-up that only resets the Program
Counter and Stack Pointer, the other flags remain in
their original status.
Entering the Power Down Mode
There is only one way for the device to enter the Power
Down Mode and that is to execute the ²HALT² instruction in the application program. When this instruction is
executed, the following will occur:
· The system oscillator will stop running and the appli-
cation program will stop at the ²HALT² instruction.
· The Data Memory contents and registers will maintain
Each pin on Port A can be setup via an individual configuration option to permit a negative transition on the pin
their present condition.
· The WDT will be cleared and resume counting if the
to wake-up the system. When a Port A pin wake-up occurs, the program will resume execution at the instruction following the ²HALT² instruction.
WDT clock source is selected to come from the WDT
oscillator. The WDT will stop if its clock source originates from the system clock.
· The I/O ports will maintain their present condition.
If the system is woken up by an interrupt, then two possible situations may occur. The first is where the related
interrupt is disabled or the interrupt is enabled but the
stack is full, in which case the program will resume execution at the instruction following the ²HALT² instruction.
In this situation, the interrupt which woke-up the device
will not be immediately serviced, but will rather be serviced later when the related interrupt is finally enabled or
when a stack level becomes free. The other situation is
where the related interrupt is enabled and the stack is
not full, in which case the regular interrupt response
takes place. If an interrupt request flag is set to ²1² before entering the Power Down Mode, the wake-up function of the related interrupt will be disabled.
· In the status register, the Power Down flag, PDF, will
be set and the Watchdog time-out flag, TO, will be
cleared.
Standby Current Considerations
As the main reason for entering the Power Down Mode
is to keep the current consumption of the MCU to as low
a value as possible, perhaps only in the order of several
micro-amps, there are other considerations which must
also be taken into account by the circuit designer if the
power consumption is to be minimized. Special attention must be made to the I/O pins on the device. All
high-impedance input pins must be connected to either
a fixed high or low level as any floating input pins could
create internal oscillations and result in increased current consumption. This also applies to devices which
have different package types, as there may be
undonbed pins, which must either be setup as outputs
or if setup as inputs must have pull-high resistors connected. Care must also be taken with the loads, which
are connected to I/O pins, which are setup as outputs.
These should be placed in a condition in which minimum
current is drawn or connected only to external circuits
that do not draw current, such as other CMOS inputs.
Also note that additional standby current will also be reRev. 1.40
No matter what the source of the wake-up event is, once
a wake-up situation occurs, a time period equal to 1024
system clock periods will be required before normal system operation resumes. However, if the wake-up has
originated due to an interrupt, the actual interrupt subroutine execution will be delayed by an additional one or
more cycles. If the wake-up results in the execution of
the next instruction following the ²HALT² instruction, this
will be executed immediately after the 1024 system
clock period delay has ended.
69
September 8, 2009
HT56R64
Low Voltage Detector - LVD
Watchdog Timer
This Low Voltage Detect internal function provides a
means for the user to monitor when the power supply
voltage falls below a certain fixed level as specified in
the DC characteristics. Bits 3 and 5 of the RTCC register
are used to control the overall function of the LVD. Bit 3
is the enable/disable control bit and is known as LVDC,
when set low the overall function of the LVD will be disabled. Bit 5 is the LVD detector output bit and is known
as LVDO. Under normal operation, and when the power
supply voltage is above the specified VLVD value in the
DC characteristic section, the LVDO bit will remain at a
zero value. If the power supply voltage should fall below
this VLVD value then the LVDO bit will change to a high
value indicating a low voltage condition. Note that the
LVDO bit is a read-only bit. By polling the LVDO bit in the
RTCC register, the application program can therefore
determine the presence of a low voltage condition.
The Watchdog Timer is provided to prevent program
malfunctions or sequences from jumping to unknown locations, due to certain uncontrollable external events
such as electrical noise. It operates by providing a device reset when the Watchdog Timer counter overflows.
The Watchdog Timer clock source is provided by the internal clock, fS, which is in turn supplied by one of two
sources selected by configuration option: fSUB or fSYS/4.
Note that if the Watchdog Timer configuration option
has been disabled, then any instruction relating to its operation will result in no operation.
Most of the Watchdog Timer options, such as enable/disable, Watchdog Timer clock source and clear
instruction type are selected using configuration options. In addition to a configuration option to enable the
Watchdog Timer, there are four bits, WDTEN3~
WDTEN0, in the MISC register to offer an additional enable control of the Watchdog Timer. These bits must be
set to a specific value of 1010 to disable the Watchdog
Timer. Any other values for these bits will keep the
Watchdog Timer enabled. After power on these bits will
have the disabled value of 1010.
After power-on, or after a reset, the LVD will be switched
off by clearing the LVDC bit in the RTCC register to zero.
Note that if the LVD is enabled there will be some power
consumption associated with its internal circuitry, however, by clearing the LVDC bit to zero the power can be
minimised. It is important not to confuse the LVD with
the LVR function. In the LVR function an automatic reset
will be generated by the microcontroller, whereas in the
LVD function only the LVDO bit will be affected with no
influence on other microcontroller functions.
One of the WDT clock sources is the internal fSUB, which
can be sourced from either the 32K_INT internal oscillator or the RTC oscillator. The 32K_INT internal oscillator
has an approximate period of 31.2ms at a supply voltage
of 5V. However, it should be noted that this specified internal clock period can vary with VDD, temperature and
process variations. The RTC oscillator is supplied by an
external 32768Hz crystal. The other Watchdog Timer
There are a range of voltage values, selected using a
configuration option, which can be chosen to activate
the LVD.
C L R W D T 1 F la g
C le a r W D T T y p e
C o n fig u r a tio n O p tio n
C L R W D T 2 F la g
1 o r 2 In s tr u c tio n s
fS
Y S
/4
fR
T C
fR
C 3 2 K
C L R
fS S o u rc e
C o n fig u r a tio n O p tio n
fS
1 6 - b it C o u n te r
C o n fig O p tio n
W D T T im e - o u t
(2 13/fS , 2 14/fS , 2 15/fS o r 2
1 6
/fS )
Watchdog Timer
b 7
O D E 3
O D E 2
O D E 1
O D E 0
W D T E N 3
W D T E N 2
W D T E N 1
b 0
W D T E N 0
M IS C
R e g is te r
W a tc h d o g T im e r E n a b le C o n tr o l
W D T E N 3 W D T E N 2 W D T E N 1 W D T E N 0
1
1
0
0
a ll o th e r v a lu e s
d is a b le
e n a b le
P A 0 ~ P A 3 O p e n D r a in C o n tr o l
- d e s c r ib e d e ls e w h e r e
Watchdog Timer Software Control - MISC
Rev. 1.40
70
September 8, 2009
HT56R64
the status register will be set and only the Program
Counter and Stack Pointer will be reset. Three methods
can be adopted to clear the contents of the Watchdog
Timer. The first is an external hardware reset, which
means a low level on the RES pin, the second is using
the watchdog software instructions and the third is via a
²HALT² instruction.
clock source option is the fSYS/4 clock. Whether the
Watchdog Timer clock source is its own internal
32K_INT, the RTC oscillator or fSYS/4, it is divided by
213~216, using configuration option to obtain the required Watchdog Timer time-out period. The max time
out period is when the 216 option is selected. This
time-out period may vary with temperature, VDD and
process variations. As the clear instruction only resets
the last stage of the divider chain, for this reason the actual division ratio and corresponding Watchdog Timer
time-out can vary by a factor of two. The exact division
ratio depends upon the residual value in the Watchdog
Timer counter before the clear instruction is executed.
There are two methods of using software instructions to
clear the Watchdog Timer, one of which must be chosen
by configuration option. The first option is to use the single ²CLR WDT² instruction while the second is to use the
two commands ²CLR WDT1² and ²CLR WDT2². For the
first option, a simple execution of ²CLR WDT² will clear
the WDT while for the second option, both ²CLR WDT1²
and ²CLR WDT2² must both be executed to successfully
clear the Watchdog Timer. Note that for this second option, if ²CLR WDT1² is used to clear the Watchdog Timer,
successive executions of this instruction will have no effect, only the execution of a ²CLR WDT2² instruction will
clear the Watchdog Timer. Similarly after the ²CLR
WDT2² instruction has been executed, only a successive
²CLR WDT1² instruction can clear the Watchdog Timer.
If the fSYS/4 clock is used as the Watchdog Timer clock
source, it should be noted that when the system enters
the Power Down Mode, then the instruction clock is
stopped and the Watchdog Timer will lose its protecting
purposes. For systems that operate in noisy environments, using the 32K_INT RC oscillator is strongly recommended.
Under normal program operation, a Watchdog Timer
time-out will initialise a device reset and set the status bit
TO. However, if the system is in the Power Down Mode,
when a Watchdog Timer time-out occurs, the TO bit in
Configuration Options
Configuration options refer to certain options within the MCU that are programmed into the device during the programming process. During the development process, these options are selected using the HT-IDE software development
tools. As these options are programmed into the device using the hardware programming tools, once they are selected
they cannot be changed later as the application software has no control over the configuration options. All options must
be defined for proper system function, the details of which are shown in the table.
No.
Options
Oscillator Options
1
Oscillator type selection:
External Crystal Oscillator
External RC Oscillator
Externally supplied clock - internal filter on
Externally supplied clock - internal filter off
2
fSUB clock selection: RTC or 32K_INT
3
fS clock selection: fSUB or fSYS/4
4
XTAL mode selection: 455KHz or 1M~12MHz
5
32768 XTAL: enable or disable
PFD Options
6
PA3: normal I/O or PFD output
7
PFD clock selection: Timer/Event Counter 0 or Timer/Event Counter 1
Buzzer Options
8
PA0/PA1: normal I/O or BZ/BZ or PA0=BZ and PA1 as normal I/O
9
Buzzer frequency: fS/22, fS/23, fS/24, fS/25, fS/26, fS/27, fS/28, fS/29
Rev. 1.40
71
September 8, 2009
HT56R64
No.
Options
Time Base Options
10
Time base time-out period: 212/fS, 213/fS, 214/fS, 215/fS,
LCD Options
11
LCD type: R or C
Watchdog Options
12
Watchdog Timer function: enable or disable
13
CLRWDT instructions: 1 or 2 instructions
14
WDT time-out period: 212/fS~213/fS, 213/fS~214/fS, 214/fS~215/fS, 215/fS~216/fS
LVD/LVR Options
15
LVD function: enable or disable
16
LVR function: enable or disable
17
LVR/LVD voltage: 2.1V/2.2V or 3.15V/3.3V or 4.2V/4.4V
SPI
18
SPI pin enable/disable
19
SPI_CPOL : clock polarity is rising or falling edge
20
SPI_WCOL : enable/disable
21
SPI_CSEN : enable/disable, used to enable/disable (1/0) software CSEN function
22
I2C pin enable (if SPI & I2C both function pin enabled. SPI pin has higher priority)
2
IC
PCLK function
23
Peripheral Clock Output - PCLK or Segment pin - SEG14
PINTB function
24
External peripheral interrupt or Segment function
Timer/Event Counter and External Interrupt pins filter function
25
Interrupt and Timer/Event Counter input pins internal filter On/Off control - applies to all pins
Lock Options
26
Lock All
27
Partial Lock
Rev. 1.40
72
September 8, 2009
HT56R64
Application Circuits
V
D D
0 .0 1 m F
0 .1 m F
V D D
3 0 0 W
0 .1 ~ 1 m F
P A 0 /B
P A 1 /B
P A
A 3 /P F
4 /T M R
5 /T M R
A 6 , P A
R e s e t
C ir c u it
1 0 k W ~
1 0 0 k W
1 N 4 1 4 8
C O M 0 ~ C O M 2
C O M 3 /S E G 3 2
S E G 0 ~ S E G 3 1
R E S
P
P A
P A
P
V S S
L C D
P a n e l
Z
Z
2
D
V
2
D D
3
7
R
P B 0 /A N 0
R C S y s te m O s c illa to r
2 4 k W < R O S C < 7 5 0 k W
O S C
~
4 7 0 p F
P B 7 /A N 7
Y S
/4
O S C 2
~
P D 0 /P W M 0
O S C 1
fS
C 1
P D 3 /P W M 3
P D 4 /IN T 0
O S C 1
O S C
C ir c u it
O S C 2
R
P D 5 /IN T 1
P D 6 /T M R 0
C 2
P D 7 /T M R 1
C 1
C 3
0 .1 m F
O S C
C ir c u it
C 2
O S C 3
R
0 .1 m F
V L C D 2
0 .1 m F
D D
O S C 3
73
C r y s ta l/R e
S y s te m O s
F o r d e ta ils
C 1 , C 2 a n d
O s c illa to r S
s o n a to r
c illa to r
r e g a r d in g
R 1 s e e
e c tio n
3 2 7 6 8 H z C ry s ta l
O s c illa to r
O S C 4
O S C 3
O S C 3 , O S C 4 F lo a tin g
O S C 4
O S C
H T 5 6 R 6 4
Rev. 1.40
C 4
V
V L C D 1
V M A X
O S C 2
P 2
V 1
O S C 4
O S C 1
P 1
C ir c u it
September 8, 2009
HT56R64
Instruction Set
sure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for subtraction. The increment and decrement instructions
INC, INCA, DEC and DECA provide a simple means of
increasing or decreasing by a value of one of the values
in the destination specified.
Introduction
C e n t ra l t o t he s uc c es s f ul oper a t i on o f a n y
microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to
perform certain operations. In the case of Holtek
microcontrollers, a comprehensive and flexible set of
over 60 instructions is provided to enable programmers
to implement their application with the minimum of programming overheads.
Logical and Rotate Operations
The standard logical operations such as AND, OR, XOR
and CPL all have their own instruction within the Holtek
microcontroller instruction set. As with the case of most
instructions involving data manipulation, data must pass
through the Accumulator which may involve additional
programming steps. In all logical data operations, the
zero flag may be set if the result of the operation is zero.
Another form of logical data manipulation comes from
the rotate instructions such as RR, RL, RRC and RLC
which provide a simple means of rotating one bit right or
left. Different rotate instructions exist depending on program requirements. Rotate instructions are useful for
serial port programming applications where data can be
rotated from an internal register into the Carry bit from
where it can be examined and the necessary serial bit
set high or low. Another application where rotate data
operations are used is to implement multiplication and
division calculations.
For easier understanding of the various instruction
codes, they have been subdivided into several functional groupings.
Instruction Timing
Most instructions are implemented within one instruction cycle. The exceptions to this are branch, call, or table read instructions where two instruction cycles are
required. One instruction cycle is equal to 4 system
clock cycles, therefore in the case of an 8MHz system
oscillator, most instructions would be implemented
within 0.5ms and branch or call instructions would be implemented within 1ms. Although instructions which require one more cycle to implement are generally limited
to the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other instructions
which involve manipulation of the Program Counter Low
register or PCL will also take one more cycle to implement. As instructions which change the contents of the
PCL will imply a direct jump to that new address, one
more cycle will be required. Examples of such instructions would be ²CLR PCL² or ²MOV PCL, A². For the
case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then
this will also take one more cycle, if no skip is involved
then only one cycle is required.
Branches and Control Transfer
Program branching takes the form of either jumps to
specified locations using the JMP instruction or to a subroutine using the CALL instruction. They differ in the
sense that in the case of a subroutine call, the program
must return to the instruction immediately when the subroutine has been carried out. This is done by placing a
return instruction RET in the subroutine which will cause
the program to jump back to the address right after the
CALL instruction. In the case of a JMP instruction, the
program simply jumps to the desired location. There is
no requirement to jump back to the original jumping off
point as in the case of the CALL instruction. One special
and extremely useful set of branch instructions are the
conditional branches. Here a decision is first made regarding the condition of a certain data memory or individual bits. Depending upon the conditions, the program
will continue with the next instruction or skip over it and
jump to the following instruction. These instructions are
the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data bits.
Moving and Transferring Data
The transfer of data within the microcontroller program
is one of the most frequently used operations. Making
use of three kinds of MOV instructions, data can be
transferred from registers to the Accumulator and
vice-versa as well as being able to move specific immediate data directly into the Accumulator. One of the most
important data transfer applications is to receive data
from the input ports and transfer data to the output ports.
Arithmetic Operations
The ability to perform certain arithmetic operations and
data manipulation is a necessary feature of most
microcontroller applications. Within the Holtek
microcontroller instruction set are a range of add and
subtract instruction mnemonics to enable the necessary
arithmetic to be carried out. Care must be taken to en-
Rev. 1.40
74
September 8, 2009
HT56R64
Bit Operations
Other Operations
The ability to provide single bit operations on Data Memory is an extremely flexible feature of all Holtek
microcontrollers. This feature is especially useful for
output port bit programming where individual bits or port
pins can be directly set high or low using either the ²SET
[m].i² or ²CLR [m].i² instructions respectively. The feature removes the need for programmers to first read the
8-bit output port, manipulate the input data to ensure
that other bits are not changed and then output the port
with the correct new data. This read-modify-write process is taken care of automatically when these bit operation instructions are used.
In addition to the above functional instructions, a range
of other instructions also exist such as the ²HALT² instruction for Power-down operations and instructions to
control the operation of the Watchdog Timer for reliable
program operations under extreme electric or electromagnetic environments. For their relevant operations,
refer to the functional related sections.
Instruction Set Summary
The following table depicts a summary of the instruction
set categorised according to function and can be consulted as a basic instruction reference using the following listed conventions.
Table Read Operations
Table conventions:
Data storage is normally implemented by using registers. However, when working with large amounts of
fixed data, the volume involved often makes it inconvenient to store the fixed data in the Data Memory. To overcome this problem, Holtek microcontrollers allow an
area of Program Memory to be setup as a table where
data can be directly stored. A set of easy to use instructions provides the means by which this fixed data can be
referenced and retrieved from the Program Memory.
Mnemonic
x: Bits immediate data
m: Data Memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Description
Cycles
Flag Affected
1
1Note
1
1
1Note
1
1
1Note
1
1Note
1Note
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
C
1
1
1
1Note
1Note
1Note
1
1
1
1Note
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
1
1Note
1
1Note
Z
Z
Z
Z
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Add Data Memory to ACC
Add ACC to Data Memory
Add immediate data to ACC
Add Data Memory to ACC with Carry
Add ACC to Data memory with Carry
Subtract immediate data from the ACC
Subtract Data Memory from ACC
Subtract Data Memory from ACC with result in Data Memory
Subtract Data Memory from ACC with Carry
Subtract Data Memory from ACC with Carry, result in Data Memory
Decimal adjust ACC for Addition with result in Data Memory
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
Logical AND Data Memory to ACC
Logical OR Data Memory to ACC
Logical XOR Data Memory to ACC
Logical AND ACC to Data Memory
Logical OR ACC to Data Memory
Logical XOR ACC to Data Memory
Logical AND immediate Data to ACC
Logical OR immediate Data to ACC
Logical XOR immediate Data to ACC
Complement Data Memory
Complement Data Memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rev. 1.40
Increment Data Memory with result in ACC
Increment Data Memory
Decrement Data Memory with result in ACC
Decrement Data Memory
75
September 8, 2009
HT56R64
Mnemonic
Description
Cycles
Flag Affected
Rotate Data Memory right with result in ACC
Rotate Data Memory right
Rotate Data Memory right through Carry with result in ACC
Rotate Data Memory right through Carry
Rotate Data Memory left with result in ACC
Rotate Data Memory left
Rotate Data Memory left through Carry with result in ACC
Rotate Data Memory left through Carry
1
1Note
1
1Note
1
1Note
1
1Note
None
None
C
C
None
None
C
C
Move Data Memory to ACC
Move ACC to Data Memory
Move immediate data to ACC
1
1Note
1
None
None
None
Clear bit of Data Memory
Set bit of Data Memory
1Note
1Note
None
None
Jump unconditionally
Skip if Data Memory is zero
Skip if Data Memory is zero with data movement to ACC
Skip if bit i of Data Memory is zero
Skip if bit i of Data Memory is not zero
Skip if increment Data Memory is zero
Skip if decrement Data Memory is zero
Skip if increment Data Memory is zero with result in ACC
Skip if decrement Data Memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1Note
1note
1Note
1Note
1Note
1Note
1Note
1Note
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read table (current page) to TBLH and Data Memory
Read table (last page) to TBLH and Data Memory
2Note
2Note
None
None
No operation
Clear Data Memory
Set Data Memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of Data Memory
Swap nibbles of Data Memory with result in ACC
Enter power down mode
1
1Note
1Note
1
1
1
1Note
1
1
None
None
None
TO, PDF
TO, PDF
TO, PDF
None
None
TO, PDF
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
1. For skip instructions, if the result of the comparison involves a skip then two cycles are required,
if no skip takes place only one cycle is required.
2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution.
3. For the ²CLR WDT1² and ²CLR WDT2² instructions the TO and PDF flags may be affected by
the execution status. The TO and PDF flags are cleared after both ²CLR WDT1² and
²CLR WDT2² instructions are consecutively executed. Otherwise the TO and PDF flags
remain unchanged.
Rev. 1.40
76
September 8, 2009
HT56R64
Instruction Definition
ADC A,[m]
Add Data Memory to ACC with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the Accumulator.
Operation
ACC ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADCM A,[m]
Add ACC to Data Memory with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADD A,[m]
Add Data Memory to ACC
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
ADD A,x
Add immediate data to ACC
Description
The contents of the Accumulator and the specified immediate data are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + x
Affected flag(s)
OV, Z, AC, C
ADDM A,[m]
Add ACC to Data Memory
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
AND A,[m]
Logical AND Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
Z
AND A,x
Logical AND immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical AND
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
Z
ANDM A,[m]
Logical AND ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
Z
Rev. 1.40
77
September 8, 2009
HT56R64
CALL addr
Subroutine call
Description
Unconditionally calls a subroutine at the specified address. The Program Counter then increments by 1 to obtain the address of the next instruction which is then pushed onto the
stack. The specified address is then loaded and the program continues execution from this
new address. As this instruction requires an additional operation, it is a two cycle instruction.
Operation
Stack ¬ Program Counter + 1
Program Counter ¬ addr
Affected flag(s)
None
CLR [m]
Clear Data Memory
Description
Each bit of the specified Data Memory is cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
None
CLR [m].i
Clear bit of Data Memory
Description
Bit i of the specified Data Memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
None
CLR WDT
Clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT1
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT2 and must be executed alternately with CLR WDT2 to have effect. Repetitively executing this instruction without alternately executing CLR WDT2 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT2
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT1 and must be executed alternately with CLR WDT1 to have effect. Repetitively executing this instruction without alternately executing CLR WDT1 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
Rev. 1.40
78
September 8, 2009
HT56R64
CPL [m]
Complement Data Memory
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa.
Operation
[m] ¬ [m]
Affected flag(s)
Z
CPLA [m]
Complement Data Memory with result in ACC
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa. The complemented result
is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
Z
DAA [m]
Decimal-Adjust ACC for addition with result in Data Memory
Description
Convert the contents of the Accumulator value to a BCD ( Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or
if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble
remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of
6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C
flag may be affected by this instruction which indicates that if the original BCD sum is
greater than 100, it allows multiple precision decimal addition.
Operation
[m] ¬ ACC + 00H or
[m] ¬ ACC + 06H or
[m] ¬ ACC + 60H or
[m] ¬ ACC + 66H
Affected flag(s)
C
DEC [m]
Decrement Data Memory
Description
Data in the specified Data Memory is decremented by 1.
Operation
[m] ¬ [m] - 1
Affected flag(s)
Z
DECA [m]
Decrement Data Memory with result in ACC
Description
Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] - 1
Affected flag(s)
Z
HALT
Enter power down mode
Description
This instruction stops the program execution and turns off the system clock. The contents
of the Data Memory and registers are retained. The WDT and prescaler are cleared. The
power down flag PDF is set and the WDT time-out flag TO is cleared.
Operation
TO ¬ 0
PDF ¬ 1
Affected flag(s)
TO, PDF
Rev. 1.40
79
September 8, 2009
HT56R64
INC [m]
Increment Data Memory
Description
Data in the specified Data Memory is incremented by 1.
Operation
[m] ¬ [m] + 1
Affected flag(s)
Z
INCA [m]
Increment Data Memory with result in ACC
Description
Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] + 1
Affected flag(s)
Z
JMP addr
Jump unconditionally
Description
The contents of the Program Counter are replaced with the specified address. Program
execution then continues from this new address. As this requires the insertion of a dummy
instruction while the new address is loaded, it is a two cycle instruction.
Operation
Program Counter ¬ addr
Affected flag(s)
None
MOV A,[m]
Move Data Memory to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
None
MOV A,x
Move immediate data to ACC
Description
The immediate data specified is loaded into the Accumulator.
Operation
ACC ¬ x
Affected flag(s)
None
MOV [m],A
Move ACC to Data Memory
Description
The contents of the Accumulator are copied to the specified Data Memory.
Operation
[m] ¬ ACC
Affected flag(s)
None
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
No operation
Affected flag(s)
None
OR A,[m]
Logical OR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
Z
Rev. 1.40
80
September 8, 2009
HT56R64
OR A,x
Logical OR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
Z
ORM A,[m]
Logical OR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²OR² [m]
Affected flag(s)
Z
RET
Return from subroutine
Description
The Program Counter is restored from the stack. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
Affected flag(s)
None
RET A,x
Return from subroutine and load immediate data to ACC
Description
The Program Counter is restored from the stack and the Accumulator loaded with the
specified immediate data. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
None
RETI
Return from interrupt
Description
The Program Counter is restored from the stack and the interrupts are re-enabled by setting the EMI bit. EMI is the master interrupt global enable bit. If an interrupt was pending
when the RETI instruction is executed, the pending Interrupt routine will be processed before returning to the main program.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
None
RL [m]
Rotate Data Memory left
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ [m].7
Affected flag(s)
None
RLA [m]
Rotate Data Memory left with result in ACC
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ [m].7
Affected flag(s)
None
Rev. 1.40
81
September 8, 2009
HT56R64
RLC [m]
Rotate Data Memory left through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7
replaces the Carry bit and the original carry flag is rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RLCA [m]
Rotate Data Memory left through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces
the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in
the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RR [m]
Rotate Data Memory right
Description
The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into
bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ [m].0
Affected flag(s)
None
RRA [m]
Rotate Data Memory right with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data
Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ [m].0
Affected flag(s)
None
RRC [m]
Rotate Data Memory right through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0
replaces the Carry bit and the original carry flag is rotated into bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
C
RRCA [m]
Rotate Data Memory right through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is
stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
C
Rev. 1.40
82
September 8, 2009
HT56R64
SBC A,[m]
Subtract Data Memory from ACC with Carry
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result
of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or
zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SBCM A,[m]
Subtract Data Memory from ACC with Carry and result in Data Memory
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SDZ [m]
Skip if decrement Data Memory is 0
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0 the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] - 1
Skip if [m] = 0
Affected flag(s)
None
SDZA [m]
Skip if decrement Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0, the program proceeds with the following instruction.
Operation
ACC ¬ [m] - 1
Skip if ACC = 0
Affected flag(s)
None
SET [m]
Set Data Memory
Description
Each bit of the specified Data Memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
None
SET [m].i
Set bit of Data Memory
Description
Bit i of the specified Data Memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
None
Rev. 1.40
83
September 8, 2009
HT56R64
SIZ [m]
Skip if increment Data Memory is 0
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] + 1
Skip if [m] = 0
Affected flag(s)
None
SIZA [m]
Skip if increment Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0 the program proceeds with the following instruction.
Operation
ACC ¬ [m] + 1
Skip if ACC = 0
Affected flag(s)
None
SNZ [m].i
Skip if bit i of Data Memory is not 0
Description
If bit i of the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is 0 the program proceeds with the following instruction.
Operation
Skip if [m].i ¹ 0
Affected flag(s)
None
SUB A,[m]
Subtract Data Memory from ACC
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUBM A,[m]
Subtract Data Memory from ACC with result in Data Memory
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUB A,x
Subtract immediate data from ACC
Description
The immediate data specified by the code is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will
be set to 1.
Operation
ACC ¬ ACC - x
Affected flag(s)
OV, Z, AC, C
Rev. 1.40
84
September 8, 2009
HT56R64
SWAP [m]
Swap nibbles of Data Memory
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged.
Operation
[m].3~[m].0 « [m].7 ~ [m].4
Affected flag(s)
None
SWAPA [m]
Swap nibbles of Data Memory with result in ACC
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged. The
result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC.3 ~ ACC.0 ¬ [m].7 ~ [m].4
ACC.7 ~ ACC.4 ¬ [m].3 ~ [m].0
Affected flag(s)
None
SZ [m]
Skip if Data Memory is 0
Description
If the contents of the specified Data Memory is 0, the following instruction is skipped. As
this requires the insertion of a dummy instruction while the next instruction is fetched, it is a
two cycle instruction. If the result is not 0 the program proceeds with the following instruction.
Operation
Skip if [m] = 0
Affected flag(s)
None
SZA [m]
Skip if Data Memory is 0 with data movement to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator. If the value is
zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the
program proceeds with the following instruction.
Operation
ACC ¬ [m]
Skip if [m] = 0
Affected flag(s)
None
SZ [m].i
Skip if bit i of Data Memory is 0
Description
If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is not 0, the program proceeds with the following instruction.
Operation
Skip if [m].i = 0
Affected flag(s)
None
TABRDC [m]
Read table (current page) to TBLH and Data Memory
Description
The low byte of the program code (current page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
TABRDL [m]
Read table (last page) to TBLH and Data Memory
Description
The low byte of the program code (last page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
Rev. 1.40
85
September 8, 2009
HT56R64
XOR A,[m]
Logical XOR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XORM A,[m]
Logical XOR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XOR A,x
Logical XOR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Z
Rev. 1.40
86
September 8, 2009
HT56R64
Package Information
52-pin QFP (14mm´14mm) Outline Dimensions
C
H
D
3 9
G
2 7
I
2 6
4 0
F
A
B
E
1 4
5 2
K
J
1
Symbol
Rev. 1.40
1 3
Dimensions in mm
Min.
Nom.
Max.
A
17.3
¾
17.5
B
13.9
¾
14.1
C
17.3
¾
17.5
D
13.9
¾
14.1
E
¾
1
¾
F
¾
0.4
¾
G
2.5
¾
3.1
H
¾
¾
3.4
I
¾
0.1
¾
J
0.73
¾
1.03
K
0.1
¾
0.2
a
0°
¾
7°
87
September 8, 2009
HT56R64
64-pin LQFP (7mm´7mm) Outline Dimensions
C
D
4 8
G
3 3
H
I
3 2
4 9
F
A
B
E
6 4
1 7
K
a
J
1 6
1
Symbol
Rev. 1.40
Dimensions in mm
Min.
Nom.
Max.
A
8.9
¾
9.1
B
6.9
¾
7.1
C
8.9
¾
9.1
D
6.9
¾
7.1
E
¾
0.4
¾
F
0.13
¾
0.23
G
1.35
¾
1.45
H
¾
¾
1.6
I
0.05
¾
0.15
J
0.45
¾
0.75
K
0.09
¾
0.20
a
0°
¾
7°
88
September 8, 2009
HT56R64
100-pin QFP (14mm´20mm) Outline Dimensions
C
H
D
8 0
G
5 1
I
5 0
8 1
F
A
B
E
3 1
1 0 0
K
a
J
1
Symbol
Rev. 1.40
3 0
Dimensions in mm
Min.
Nom.
Max.
A
18.50
¾
19.20
B
13.90
¾
14.10
C
24.50
¾
25.20
D
19.90
¾
20.10
E
¾
0.65
¾
F
¾
0.30
¾
G
2.50
¾
3.10
H
¾
¾
3.40
I
¾
0.10
¾
J
1
¾
1.40
K
0.10
¾
0.20
a
0°
¾
7°
89
September 8, 2009
HT56R64
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shenzhen Sales Office)
5F, Unit A, Productivity Building, No.5 Gaoxin M 2nd Road, Nanshan District, Shenzhen, China 518057
Tel: 86-755-8616-9908, 86-755-8616-9308
Fax: 86-755-8616-9722
Holtek Semiconductor (USA), Inc. (North America Sales Office)
46729 Fremont Blvd., Fremont, CA 94538, USA
Tel: 1-510-252-9880
Fax: 1-510-252-9885
http://www.holtek.com
Copyright Ó 2009 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.40
90
September 8, 2009