HANBit HMN1288J Non-Volatile SRAM MODULE 1Mbit (128K x 8-Bit),34Pin-JLCC, 5V Part No. HMN1288J GENERAL DESCRIPTION The HMN1288J Nonvolatile SRAM is a 1,048,576-bit static RAM organized as 131,072 bytes by 8 bits. The HMN1288J has a self-contained lithium energy source provide reliable non-volatility coupled with the unlimited write cycles of standard SRAM and integral control circuitry which constantly monitors the single 5V supply for an out-oftolerance condition. When such a condition occurs, the lithium energy source is automatically switched on to sustain the memory until after Vcc returns valid and write protection is unconditionally enabled to prevent garbled data. In addition the SRAM is unconditionally write-protected to prevent an inadvertent write operation. At this time the integral energy source is switched on to sustain the memory until after VCC returns valid. The HMN1288J uses extremely low standby current CMOS SRAM’s, coupled with small lithium coin cells to provide nonvolatility without long write-cycle times and the write-cycle limitations associated with EEPROM. PIN ASSIGNMENT FEATURES w Access time : 55, 70 ns /NBW A(15) A(16) /RST VCC /WE /OE /CE D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0) VSS w High-density design : 4Mbit Design w Battery internally isolated until power is applied w Industry-standard 34-pin 128K x 8 pinout w Unlimited write cycles w Data retention in the absence of VCC w 10-years minimum data retention in absence of power w Automatic write-protection during power-up/power-down cycles w Data is automatically protected during power loss w Conventional SRAM operation; unlimited write cycles 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 NC NC A(14) A(13) A(12) A(11) A(10) A(9) A(8) A(7) A(6) A(5) A(4) A(3) A(2) A(1) A(0) JLCC TOP VIEW OPTIONS MARKING w Timing 55 ns -55 70 ns -70 URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) 1 HANBit Electronics Co.,Ltd. HANBit HMN1288J FUNCTIONAL DESCRIPTION The HMN1288J executes a read cycle whenever /WE is inactive(high) and /CE is active(low). The address specified by the address inputs(A0-A16) defines which of the 131,072 bytes of data is accessed. Valid data will be available to the eight data output drivers within tACC (access time) after the last address input signal is stable. When power is valid, the HMN1288J operates as a standard CMOS SRAM. During power-down and power-up cycles, the HMN1288J acts as a nonvolatile memory, automatically protecting and preserving the memory contents. The HMN1288J is in the write mode whenever the /WE and /CE signals are in the active (low) state after address inputs are stable. The later occurring falling edge of /CE or /WE will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of /CE or /WE. All address inputs must be kept valid throughout the write cycle. /WE must return to the high state for a minimum recovery time (tWR) before another cycle can be initiated. The /OE control signal should be kept inactive (high) during write cycles to avoid bus contention. However, if the output bus been enabled (/CE and /OE active) then /WE will disable the outputs in tODW from its falling edge. The HMN1288J provides full functional capability for Vcc greater than 4.75 V and write protects by 4.5 V nominal. Powerdown/power-up control circuitry constantly monitors the Vcc supply for a power-fail-detect threshold VPFD. When VCC falls below the VPFD threshold, the SRAM automatically write-protects the data. All inputs to the RAM become “don’t care” and all outputs are high impedance. As Vcc falls below approximately 2.7 V, the power switching circuit connects the lithium energy soure to RAM to retain data. During power-up, when Vcc rises above approximately 2.7 volts, the power switching circuit connects external Vcc to the RAM and disconnects the lithium energy source. Normal RAM operation can resume after Vcc exceeds 4.75 volts. BLOCK DIAGRAM /OE PIN DESCRIPTION A(0:16) A0-A16 : Address Input /WE DQ(0:7) /CE : Chip Enable /CE1 VSS : Ground DQ0-DQ7 : Data In / Data Out Vcc /CE2 /WE : Write Enable Vout /CE /RESET /OE : Output Enable /CE_con VCC: Power (+5V) Vcc NC : No Connection URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) 2 HANBit Electronics Co.,Ltd. HANBit HMN1288J TRUTH TABLE MODE /OE /CE /WE I/O OPERATION POWER Not selected X H X High Z Standby Output disable H L H High Z Active Read L L H DOUT Active Write X L L DIN Active ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING VCC -0.3V to 7.0 VT -0.3V to Vcc+0.3 Operating temperature TOPR 0 to 70°C Storage temperature TSTG -55°C to 125°C TSOLDER 260°C DC voltage applied on VCC relative to VSS DC Voltage applied on any pin excluding VCC relative to VSS Soldering temperature CONDITIONS VT≤ VCC+0.3 For 10 second NOTE: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. RECOMMENDED DC OPERATING CONDITIONS ( TA= TOPR ) PARAMETER Supply Voltage SYMBOL VCC MIN 4.5V TYPICAL - MAX 5.5V Ground VSS 0 0 0 Input high voltage VIH 2.0 - VCC+0.3 Input low voltage VIL -0.3 - 0.8V NOTE: Typical values indicate operation at TA = 25℃ CAPACITANCE (TA=25℃ , f=1MHz, VCC=5V) DESCRIPTION Input Capacitance Input/Output Capacitance URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) CONDITIONS SYMBOL MAX MIN UNIT Input voltage = 0V CIN 8 - pF Output voltage = 0V CI/O 10 - pF 3 HANBit Electronics Co.,Ltd. HANBit HMN1288J DC ELECTRICAL CHARACTERISTICS (TA= TOPR, VCCmin £ VCC ≤ VCCmax ) PARAMETER CONDITIONS SYMBOL MIN TYP. MAX UNIT Input Leakage Current VIN=VSS to VCC ILI - - ± 2.0 mA Output Leakage Current ILO - - ± 2.0 mA Output high voltage /CE=VIH or /OE=VIH or /WE=VIL IOH=-1.0mA VOH 2.4 - - V Output low voltage IOL= 2.0mA VOL - - 0.4 V VCCTP 4.5 4.62 4.75 V VCC Trip Point (TOL=GND) Standby supply current /CE=2.2v ISB - - 3 mA Standby supply current /CE≥ VCC-0.3V, ISB1 - - 150 mA /CE=VIL, II/O=0㎃ , VIN = VIL or VIH, Read ICC - - 12 mA VSW 2.6 2.7 2.8 V Operating Power supply current VCC/VBAT Switch Point NOTE: Typical values indicate operation at TA = 25℃ . CHARACTERISTICS (Test Conditions) PARAMETER VALUE Input pulse levels 0.8 to 2.4V Input rise and fall times CL1) Including scope and jig capacitance 5 ns Input and output timing reference levels 1) Output load (CL =50pF+1TTL) 1) (CL =100pF+1TTL) 1.5V ( unless otherwise specified) See Figures READ CYCLE (TA= TOPR, VCCmin £ VCC≤ VCCmax ) PARAMETER SYMBOL CONDITIONS Read Cycle Time tRC Address Access Time tACC Output load A Chip enable access time tACE Output load A Output enable to Output valid tOE Output load A -55 -70 UNIT MIN MAX MIN MAX 55 - 70 - ns - 55 - 70 ns 55 - 70 ns - 25 - 35 ns Chip enable to output in low Z tCLZ Output load B 10 - 10 - ns Output enable to output in low Z tOLZ Output load B 5 - 5 - ns Chip disable to output in high Z tCHZ Output load B 0 20 0 25 ns Output disable to output high Z tOHZ Output load B 0 20 0 25 ns Output hold from address change tOH Output load A 10 - 10 - ns URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) 4 HANBit Electronics Co.,Ltd. HANBit HMN1288J WRITE CYCLE (TA= TOPR, Vccmin £ Vcc ≤ Vccmax ) PARAMETER SYMBOL Write Cycle Time tWC Chip enable to end of write tCW Address setup time Address valid to end of write -70 CONDITIONS -85 UNIT MIN MAX MIN MAX 55 - 70 - ns Note 1 45 - 60 - ns tAS Note 2 0 - 0 - ns tAW Note 1 45 - 60 - ns - 50 - ns Write pulse width tWP Note 1 40 Write recovery time (write cycle 1) tWR1 Note 3 5 - 5 - ns Write recovery time (write cycle 2) tWR2 Note 3 15 - 15 - ns Data valid to end of write tDW 20 - 25 - ns Data hold time (write cycle 1) tDH1 Note 4 0 - 0 - ns Data hold time (write cycle 2) tDH2 Note 4 0 - 0 - ns Write enabled to output in high Z tWZ Note 5 0 20 0 25 ns Output active from end of write tOW Note 5 5 - 5 - ns NOTE: 1. A write ends at the earlier transition of /CE going high and /WE going high. 2. A write occurs during the overlap of allow /CE and a low /WE. A write begins at the later transition of /CE going low and /WE going low. 3. Either tWR1 or tWR2 must be met. 4. Either tDH1 or tDH2 must be met. 5. If /CE goes low simultaneously with /WE going low or after /WE going low, the outputs remain in highimpedance state. TIMING WAVEFORM - READ CYCLE NO.1 (Address Access)*1,2 tRC Address tACC tOH Previous Data Valid DOUT Data Valid - READ CYCLE NO.2 (/CE Access)*1,3,4 tRC /CE tACE tCHZ tCLZ DOUT URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) High-Z High-Z 5 HANBit Electronics Co.,Ltd. HANBit HMN1288J - READ CYCLE NO.3 (/OE Access)*1,5 tRC Address tACC /OE tOE DOUT tOHZ tOLZ Data Valid High-Z High-Z NOTES: 1. /WE is held high for a read cycle. 2. Device is continuously selected: /CE = /OE =VIL. 3. Address is valid prior to or coincident with /CE transition low. 4. /OE = VIL. 5. Device is continuously selected: /CE = VIL - WRITE CYCLE NO.1 (/WE-Controlled)*1,2,3 tWC Address tAW tWR1 tCW /CE tAS tWP /WE tDW DIN Data-in Valid tWZ DOUT tOW High-Z Data Undefined (1) URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) tDH1 6 HANBit Electronics Co.,Ltd. HANBit HMN1288J - WRITE CYCLE NO.2 (/CE-Controlled)*1,2,3,4,5 Address tAW tAS tWR2 tCW /CE tWP /WE tDH2 tDW Data-in DIN tWZ DOUT Data NOTE: High-Z Undefined 1. /CE or /WE must be high during address transition. 2. Because I/O may be active (/OE low) during this period, data input signals of opposite polarity to the outputs must not be applied. 3. If /OE is high, the I/O pins remain in a state of high impedance. 4. Either tWR1 or tWR2 must be met. 5. Either tDH1 or tDH2 must be met. POWER-DOWN/POWER-UP TIMING VCC tPF 4.75 VPFD VPFD 4.25 VSO VSO tFS tPU tCER tDR tWPT /CE URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) 7 HANBit Electronics Co.,Ltd. HANBit HMN1288J PACKAGE DIMENSION Unit : mm 24.52+/-0.2 23.50+/-0.2 1.27 .635 1.50 1.50 3.05 10.82 13.31 ORDERING INFORMATION H M N 128 8 J - 70 I Operating Temperature : I = Industrial Temp. (-40~85 °C ) Blank = Commercial Temp. (0~70°C) Speed options : 55 = 55 ns 70 = 70ns JLCC type package Device : 128K x 8 bit Nonvolatile SRAM HANBit Memory Module URL: www.hbe.co.kr Rev.0.0 (FEBRUARY/ 2002) 8 HANBit Electronics Co.,Ltd.