MEAN WELL PS-65 SWITCHING POWER SUPPLY SERIES ISO-9001 CERTIFIED MANUFACTURER .LOW COST, HIGH RELIABILITY .COMPACT SIZE, LIGHT WEIGHT .105ºC OUTPUT CAPACITOR .100% FULL LOAD BURN-IN TEST .INTERNATIONAL AC INPUT RANGE .BUILT IN EMI FILTER, LOW RIPPLE NOISE .HIGH EFFICIENCY, LOW WORKING TEMPERATURE .SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT .SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED MODEL PS-65-5 DC OUTPUT VOLTAGE 3.3V 5V 7.5V OUTPUT V. TOLERANCE ±3% ±3% ±3% ±2% ±2% ±2% ±2% ±2% ±2% OUTPUT RATED CURRENT 12A 12A 8A 5.2A 4.7A 4.2A 2.7A 2.4A 1.35A OUTPUT MIN. CURRENT 0A 0A 0A 0A 0A 0A 0A 0A 0A OUTPUT MAX. CURRENT 15.2A 13.8A 9.6A 6A 5.4A 4.8A 3A 2.7A 1.5A RIPPLE & NOISE p-p 80mV 100mV 100mV 100mV 100mV 100mV 100mV 100mV 100mV LINE REGULATION ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% LOAD REGULATION ±3% ±3% ±3% ±2% ±2% ±2% ±2% ±2% ±2% 39.6W 60W 60W 62.4W 63.5W 63W 64.8W 64.8W 64.8W RATED OUTPUT POWER MAXIMUM OUTPUT POWER EFFICIENCY PS-65-7.5 PS-65-12 PS-6513.5 PS-65-3.3 SPECIFICATION 12V 13.5V PS-65-15 PS-65-24 PS-65-27 PS-65-48 15V 24V 27V RATED OUTPUT POWER FOR CONVECTION; 72W (+3.3V:50W;+5V:69W) WITH 18 CFM MIN. FORCED AIR 69% 76% 79% 79% 79% 79% 80% 80% DC VOLTAGE ADJ. +10,-5% INPUT VOLTAGE RANGE 90~264VAC 47~440Hz ; 120~370VDC AC CURRENT 1.5A/115V 0.9A/230V INRUSH CURRENT COLD START 20A/115V 40A/230V LEAKAGE CURRENT <0.5mA/240VAC OVERLOAD PROTECTION 73~105W (3.3V:51~75W)(5V:70~105W) TYPE:PULSING HICCUP SHUTDOWN RESET:AUTO RECOVERY OVER VOLTAGE PROTECTION 115%~135% TEMP. COEFFICIENT ±0.04% / ºC (0~50ºC) SETUP, RISE, HOLD UP TIME 800ms, 20ms, 20ms VIBRATION 10~500Hz, 2G 10min./1cycle, PERIOD FOR 60min. EACH AXES WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M Ohms WORKING TEMP., HUMIDITY -10ºC~+60ºC(REFER TO OUTPUT DERATING CURVE), 20%~90% RH STORAGE TEMP., HUMIDITY -20ºC~+85ºC, 10%~95% RH DIMENSION 127*76.2*42mm (L*W*H) PCB ONLY WEIGHT 0.28Kgs SAFETY STANDARDS UL1950, TUV EN60950 APPROVED EMC STANDARDS CISPR22 (EN55022), IEC1000-4-2,3,4,5 IEC1000-3-2,3 VERIFICATION NOTE : 48V 80% 1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25ºC 70% RH. AMBIENT. 2.TOLERANCE GINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION. 3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR. 4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD. 5.OUTPUT PROVIDE UP TO MAXIMUM CURRENT, BUT RELATED TO MAXIMUM OUTPUT POWER. 6.MOUNTING HOLES M1 AND M2 SHOULD BE GROUNDED FOR EMI PURPOSES. 2002-04-29