TI TPS77025DBVRG4

TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
D
D
D
D
D
D
D
D
DBV PACKAGE
(TOP VIEW)
50-mA Low-Dropout Regulator
Available in 1.2-V, 1.5-V, 1.8-V, 2.5-V, 2.7-V,
2.8-V, 3.0-V, 3.3-V, and 5-V Fixed-Output and
Adjustable Versions
Only 17 µA Quiescent Current at 50 mA
1 µA Quiescent Current in Standby Mode
Dropout Voltage Typically 35 mV at 50 mA
Over Current Limitation
–40°C to 125°C Operating Junction
Temperature Range
5-Pin SOT-23 (DBV) Package
IN
1
GND
2
EN
3
5
OUT
4
NC/FB
TPS77033
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
22
description
21
Ground Current – µ A
The TPS770xx family of low-dropout (LDO)
voltage regulators offers the benefits of low
dropout voltage, ultralow-power operation, and
miniaturized packaging. These regulators feature
low dropout voltages and ultralow quiescent
current compared to conventional LDO
regulators. Offered in a 5-terminal small outline
integrated-circuit
SOT-23
package,
the
TPS770xx series devices are ideal for
micropower operations and where board space is
at a premium.
VI = 4.3 V
CO = 4.7 µF
20
19
IO = 50 mA
IO = 0 mA
18
17
16
A combination of new circuit design and process
innovation has enabled the usual PNP pass
transistor to be replaced by a PMOS pass
15
–60 –40 –20 0
20 40 60 80 100 120 140
element. Because the PMOS pass element
TA – Free-Air Temperature – °C
behaves as a low-value resistor, the dropout
voltage is very low — typically 35 mV at 50 mA of
load current (TPS77050) — and is directly proportional to the load current. Since the PMOS pass element is
a voltage-driven device, the quiescent current is ultralow (28 µA maximum) and is stable over the entire range
of output load current (0 mA to 50 mA). Intended for use in portable systems such as laptops and cellular phones,
the ultralow-dropout voltage feature and ultralow-power operation result in a significant increase in system
battery operating life.
The TPS770xx also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current
to 1 µA typical at TJ = 25°C. The TPS770xx is offered in 1.2-V, 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V,
and 5-V fixed-voltage versions and in a variable version (programmable over the range of 1.2 V to 5.5 V).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
AVAILABLE OPTIONS
VOLTAGE
TJ
PACKAGE
PART NUMBER
SYMBOL
Variable
1.2V to 5.5V
TPS77001DBVT†
TPS77001DBVR‡
PCPI
1.2 V
TPS77012DBVT†
TPS77015DBVT†
TPS77012DBVR‡
TPS77015DBVR‡
PCQI
TPS77018DBVT†
TPS77025DBVT†
TPS77018DBVR‡
TPS77025DBVR‡
PCSI
TPS77027DBVT†
TPS77028DBVT†
TPS77027DBVR‡
TPS77028DBVR‡
PCUI
TPS77030DBVR‡
TPS77033DBVR‡
PCWI
3.3 V
TPS77030DBVT†
TPS77033DBVT†
5.0 V
TPS77050DBVT†
TPS77050DBVR‡
PCYI
1.5 V
1.8 V
SOT-23
(DBV)
2.5 V
–40°C to 125°C
2.7 V
2.8 V
3.0 V
† The DBVT indicates tape and reel of 250 parts.
‡ The DBVR indicates tape and reel of 3000 parts.
functional block diagram
TPS77001
OUT
IN
EN
Current Limit
/ Thermal
Protection
VREF
FB
GND
TPS77012/15/18/25/27/28/30/33/50
OUT
IN
EN
VREF
Current Limit
/ Thermal
Protection
GND
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PCRI
PCTI
PCVI
PCXI
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
Terminal Functions
TERMINAL
NAME
I/O
NO.
DESCRIPTION
GND
2
Ground
EN
3
I
Enable input
FB
4
I
Feedback voltage (TPS77001 only)
IN
1
I
Input supply voltage
NC
4
OUT
5
No connection (Fixed options only)
O
Regulated output voltage
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)Ĕ
Input voltage range (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VI + 0.3 V
Voltage on OUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = 25°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
Low K‡
High K§
DBV
65.8 °C/W
259 °C/W
3.9 mW/°C
386 mW
212 mW
154 mW
DBV
65.8 °C/W
180 °C/W
5.6 mW/°C
555 mW
305 mW
222 mW
‡ The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board.
§ The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground
planes and 2 ounce copper traces on top and bottom of the board.
recommended operating conditions
MIN
NOM
MAX
UNIT
Input voltage, VI (see Note 2)
2.7
10
Output voltage range, VO
1.2
5.5
V
0
50
mA
–40
125
°C
Continuous output current, IO (see Note 3)
Operating junction temperature, TJ
V
NOTES: 2. To calculate the minimum input voltage for your maximum output current, use the following formula:
VI(min) = VO(max) + VDO (max load)
3. Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended
that the device operate under conditions beyond those specified in this table for extended periods of time.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
electrical characteristics over recommended operating free–air temperature range,
VI = VO(typ) + 1 V, IO = 50 mA, EN = 0V, Co = 4.7 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TPS77001
Output voltage
g (10
( µ
µA to 50 mA load))
(see Note 4)
1.2 V ≤ VO ≤ 5.5 V,
1.2 V ≤ VO ≤ 5.5 V,
MIN
TJ = 25°C
TJ = –40°C to 125°C
TPS77012
TJ = 25°C,
TJ = –40°C to 125°C,
2.7 V < VIN < 10 V
TPS77015
TJ = 25°C,
TJ = –40°C to 125°C,
2.7 V < VIN < 10 V
TPS77018
TJ = 25°C,
TJ = –40°C to 125°C,
2.8 V < VIN < 10 V
TPS77025
TJ = 25°C,
TJ = –40°C to 125°C,
TPS77027
TJ = 25°C,
TJ = –40°C to 125°C,
3.7 V < VIN < 10 V
TPS77028
TJ = 25°C,
TJ = –40°C to 125°C,
3.8 V < VIN < 10 V
TPS77030
TJ = 25°C,
TJ = –40°C to 125°C,
4.0 V < VIN < 10 V
TPS77033
TJ = 25°C,
TJ = –40°C to 125°C,
TPS77050
TJ = 25°C,
TJ = –40°C to 125°C,
6.0 V < VIN < 10 V
EN = 0V,
TJ = 25°C
0 mA < IO < 50mA,
EN = 0V,
TJ = –40°C to 125°C
IO = 50mA,
Quiescent current (GND current) (see Note 4)
2.7 V < VIN < 10 V
2.7 V < VIN < 10 V
BW = 300 Hz to 50 kHz,
Co = 10 µF,
TJ = 25°C
2.575
2.7
2.619
V
2.781
2.8
2.716
2.884
3.0
3.090
3.3
3.399
5.0
4.850
5.150
17
µA
28
0.04
0.1
IO = 0 to 50 mA,
VO = 0V,
EN = VI,
1.854
2.5
3.201
Output noise voltage
1.545
1.8
4.3 V < VIN < 10 V
EN = 0V,
TJ = 25°C
Standby current
1.5
2.910
Load regulation
1.261
1.455
4.0 V < VIN < 10 V
4.3 V < VIN < 10 V
VO + 1 V < VI ≤ 10 V, TJ = 25°C
VO + 1 V < VI ≤ 10 V,
TJ = –40°C to 125°C
1.03VO
1.187
2.425
6.0 V < VIN < 10 V
UNIT
1.224
3.5 V < VIN < 10 V
Output voltage line regulation (∆VO/VO)
(see Notes 4 and 5)
Output current limit
0.97VO
1.746
3.8 V < VIN < 10 V
MAX
VO
2.8 V < VIN < 10 V
3.5 V < VIN < 10 V
3.7 V < VIN < 10 V
TYP
8
mV
µVrms
190
See Note 4
350
2.7 < VI < 10 V
1
%/V
750
mA
µA
TJ = –40°C to 125°C
2
µA
NOTES: 4. Minimum IN operating voltage is 2.7 V or VO (typ) + 1 V, whichever is greater. Maximum IN voltage 10 V, minimum output current
10 µA, maximum output current 50 mA.
5. If VO ≤ 1.8 V then VImin = 2.7 V, VImax = 10 V:
Line Reg. (mV)
+ ǒ%ńVǓ
V
O
If VO ≥ 2.5 V then VImin = VO + 1 V, VImax = 10 V:
Line Reg. (mV)
4
+ ǒ%ńVǓ
V
POST OFFICE BOX 655303
O
ǒ
V
ǒ
* 2.7 V
Imax
100
V
Imax
*
ǒ
V
O
100
• DALLAS, TEXAS 75265
Ǔ
1000
)1 V
ǓǓ
1000
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
electrical characteristics over recommended operating free–air temperature range, VI = VO(typ) +
1 V, IO = 50 mA, EN = 0V, Co = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
MIN
FB input current
FB = 1.224 V (TPS77001)
–1
High level enable input voltage
2.7 V < VI < 10 V
1.7
Low level enable input voltage
2.7 V < VI < 10 V
Power supply ripple rejection
f = 1 kHz,
TJ = 25°C,
CO = 10 µF,
See Note 4
UNIT
µA
1
V
V
60
–1
EN = VI
0
–1
TPS77028
IO = 50 mA,
IO = 50 mA
TJ = 25°C
TJ = –40°C to 125°C
60
TPS77030
IO = 50 mA,
IO = 50 mA
TJ = 25°C
TJ = –40°C to 125°C
57
TPS77033
IO = 50 mA,
IO = 50 mA
TJ = 25°C
TJ = –40°C to 125°C
48
TPS77050
IO = 50 mA,
IO = 50 mA
TJ = 25°C
TJ = –40°C to 125°C
35
Dropout voltage (see Note 6)
MAX
0.9
EN = 0 V
Input current (EN)
TYP
dB
1
µA
1
µA
125
115
mV
100
85
NOTES: 4. Minimum IN operating voltage is 2.7 V or VO (typ) + 1 V, whichever is greater. Maximum IN voltage 10 V, minimum output current
10 µA, maximum output current 50 mA.
6. IN voltage equals VO(Typ) –100mV; TPS77001 output voltage set to 3.3 V nominal with external resistor divider. TPS77012,
TPS77015, TPS77018, TPS77025, and TPS77027 dropout voltage limited by input voltage range limitations.
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VO
Zo
VDO
vs Output current
1, 2, 3
vs Free-air temperature
4, 5, 6
Ground current
vs Free-air temperature
7
Output spectral noise density
vs Frequency
8
Output impedance
vs Frequency
9
Dropout voltage
vs Free-air temperature
10
Ripple rejection
vs Frequency
Output voltage
LDO startup time
11
12
Line transient response
13, 15
Load transient response
14, 16
Equivalent series resistance (ESR)
POST OFFICE BOX 655303
vs Output current
17, 19
vs Added ceramic capacitance
18, 20
• DALLAS, TEXAS 75265
5
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
TPS77015
TPS77025
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
1.498
2.498
VI = 3.5 V
CO = 4.7 µF
TA = 25° C
2.496
1.496
VO – Output Voltage – V
2.494
VO – Output Voltage – V
VI = 2.7 V
CO = 4.7 µF
TA = 25° C
2.492
2.490
2.488
2.486
1.494
1.492
1.490
1.488
1.486
2.484
1.484
2.482
0
10
20
30
40
0
50
10
20
30
Figure 1
TPS77033
TPS77015
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
1.496
VI = 4.3 V
CO = 4.7 µF
TA = 25° C
3.282
1.494
IO = 1 mA
VI = 2.7 V
CO = 4.7 µF
1.492
3.280
VO – Output Voltage – V
VO – Output Voltage – V
50
Figure 2
3.284
3.278
3.276
3.274
3.272
1.490
1.488
1.486
IO = 50 mA
1.484
1.482
3.270
0
10
20
30
40
50
1.480
–60 –40 –20
0
20
40
Figure 3
Figure 4
POST OFFICE BOX 655303
60
80 100 120 140
TA – Free-Air Temperature – °C
IO – Output Current – mA
6
40
IO – Output Current – mA
IO – Output Current – mA
• DALLAS, TEXAS 75265
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
TPS77025
TPS77033
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
2.496
3.285
2.494
IO = 1 mA
VO – Output Voltage – V
VO – Output Voltage – V
2.490
2.488
IO = 50 mA
2.484
2.482
2.480
2.478
3.275
3.270
IO = 50 mA
3.265
3.260
VI = 3.5 V
CO = 4.7 µF
2.476
–60 –40 –20
IO = 1 mA
3.280
2.492
2.486
VI = 4.3 V
CO = 4.7 µF
0
20
40
60
80 100 120 140
3.255
–60 –40 –20
TA – Free-Air Temperature – °C
0
20
Figure 5
TPS77033
80 100 120 140
TPS77033
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
2
VI = 4.3 V
CO = 4.7 µF
20
19
IO = 50 mA
IO = 0 mA
18
17
16
Output Spectral Noise Density – µV Hz
22
Ground Current – µ A
60
Figure 6
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
21
40
TA – Free-Air Temperature – °C
1.8
CO = 4.7 µF
IO = 50 mA
1.4
1.2
1
0.8
CO = 4.7 µF
IO = 1 mA
0.6
0.4
CO = 10 µF
IO = 50 mA
0.2
VI = 4.3 V
15
–60 –40 –20
0
20
40
60
80 100 120 140
CO = 10 µF
IO = 1 mA
1.6
0
100
TA – Free-Air Temperature – °C
1k
10k
100k
f – Frequency – Hz
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
TPS77033
OUTPUT IMPEDANCE
vs
FREQUENCY
100
2
1.8
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
VI = 4.3 V
CO = 4.7 µF
VI = 3.2 V
CO = 4.7 µF
VDO – Dropout Voltage – mV
Zo – Output Impedance – Ω
1.6
1.4
1.2
1
0.8
IO = 1 mA
0.6
0.4
10
IO = 10 mA
IO = 50 mA
0.2
0
10
IO = 50 mA
100
1k
10k
100k
1
–60 –40 –20
1M
0
20
40
60
80 100 120 140
TA – Free-Air Temperature – °C
f – Frequency – Hz
Figure 9
Figure 10
TPS77033
RIPPLE REJECTION
vs
FREQUENCY
100
LDO STARTUP TIME
90
Ripple Rejection – dB
80
EN
70
IO = 1 mA
60
50
40
30
IO = 50 mA
20
10
0
– 10
10
VI = 4.3 V
CO = 4.7 µF
ESR = 0.3 Ω
100
VO
1k
10 k
100 k
1M
10 M
0
20
40
f – Frequency – Hz
Figure 11
8
60
80 100 120 140 160 180 200
t – Time – µs
Figure 12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
TPS77015
TPS77015
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
Current Load – mA
VO – Output Voltage – mV
TYPICAL CHARACTERISTICS
10
0
–10
50
0
2.7
IL = 10 mA
CO = 4.7 µF
ESR = 0.3 Ω
0
20
40
60
80 100 120 140 160 180 200
t – Time – µs
∆ VO – Change In
Output Voltage – mV
VI – Input Voltage – V
3.7
0
–50
VI = 2.7 V
CO = 10 µF
ESR = 0.3 Ω
–100
0
20
40
Current Load – mA
TPS77033
LOAD TRANSIENT RESPONSE
0
–10
∆ VO – Change In
Output Voltage – mV
VO – Output Voltage – mV
TPS77033
LINE TRANSIENT RESPONSE
10
VI – Input Voltage – V
5.3
4.3
IL = 10 mA
CO = 4.7 µF
ESR = 0.3 Ω
20
80 100 120 140 160 180 200
t – Time – µs
Figure 14
Figure 13
0
60
40
60
80 100 120 140 160 180
t – Time – µs
50
0
0
–20
VI = 4.3 V
CO = 4.7 µF
ESR = 0.3 Ω
–40
0
20
40
60
80 100 120 140 160 180
t – Time – µs
Figure 16
Figure 15
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
TPS77033
TYPICAL REGIONS OF STABILITY
TPS77033
TYPICAL REGIONS OF STABILITY
EQUIVALENT SERIES RESISTANCE (ESR)†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE (ESR)
vs
ADDED CERAMIC CAPACITANCE
100
VIN = 4.3 V
CO = 4.7 µF
ESR = 0.3 Ω
3.3 V LDO
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
100
Region of Instability
10
1
Region of Stability
0.1
VIN = 4.3 V
CO = 4.7 µF
IL = 50 mA
Region of Instability
10
Region of Stability
1
0
5
10
15
20
25
30
35
40
45
0
50
0.1
0.9
1
Figure 18
Figure 17
TPS77033
TYPICAL REGIONS OF STABILITY
TPS77033
TYPICAL REGIONS OF STABILITY
EQUIVALENT SERIES RESISTANCE (ESR)†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE (ESR)
vs
ADDED CERAMIC CAPACITANCE
100
100
VIN = 4.3 V
CO = 10 µF
ESR = 0.3 Ω
3.3 V LDO
Region of Instability
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
0.6 0.7 0.8
Added Ceramic Capacitance – µF
IO – Output Current – mA
10
Region of Stability
VIN = 4.3 V
CO = 10 µF
IL = 50 mA
Region of Instability
10
Region of Stability
1
1
0
5
10
15
20
25
30
35
40
45
50
0
0.1
0.2 0.3 0.4 0.5
Figure 20
Figure 19
POST OFFICE BOX 655303
0.6 0.7 0.8
Added Ceramic Capacitance – µF
IO – Output Current – mA
10
0.2 0.3 0.4 0.5
• DALLAS, TEXAS 75265
0.9
1
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
APPLICATION INFORMATION
The TPS770xx family of low-dropout (LDO) regulators have been optimized for use in battery-operated
equipment. They feature extremely low dropout voltages, low quiescent current (17 µA nominally), and enable
inputs to reduce supply currents to less than 1 µA when the regulators are turned off.
device operation
The TPS770xx uses a PMOS pass element to dramatically reduce both dropout voltage and supply current over
more conventional PNP-pass-element LDO designs. The PMOS pass element is a voltage-controlled device
and, unlike a PNP transistor, it does not require increased drive current as output current increases. Supply
current in the TPS770xx is essentially constant from no load to maximum load.
Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation.
The device switches into a constant-current mode at approximately 350 mA; further load reduces the output
voltage instead of increasing the output current. The thermal protection shuts the regulator off if the junction
temperature rises above approximately 165°C. Recovery is automatic when the junction temperature drops
approximately 25°C below the high temperature trip point. The PMOS pass element includes a back gate diode
that conducts reverse current when the input voltage level drops below the output voltage level.
A voltage of 1.7 V or greater on the EN input will disable the TPS770xx internal circuitry, reducing the supply
current to 1µA. A voltage of less than 0.9 V on the EN input will enable the TPS770xx and will enable normal
operation to resume. The EN input does not include any deliberate hysteresis, and it exhibits an actual switching
threshold of approximately 1.5 V.
A typical application circuit is shown in Figure 21.
TPS770xx†
VI
C1
1 µF
1
IN
NC/FB
OUT
4
5
VO
3
EN
+
GND
2
4.7 µF
ESR = 0.2 Ω
† TPS77012, TPS77015, TPS77018, TPS77025, TPS77027,
TPS77028, TPS77030, TPS77033, TPS77050 (fixed-voltage options).
Figure 21. Typical Application Circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
APPLICATION INFORMATION
external capacitor requirements
Although not required, a 0.047-µF or larger ceramic input bypass capacitor, connected between IN and GND
and located close to the TPS770xx, is recommended to improve transient response and noise rejection. A
higher-value electrolytic input capacitor may be necessary if large, fast-rise-time load transients are anticipated
and the device is located several inches from the power source.
Like all low dropout regulators, the TPS770xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance is 4.7 µF. The ESR (equivalent
series resistance) of the capacitor should be between 0.2 Ω and 10 Ω. to ensure stability. Capacitor values larger
than 4.7 µF are acceptable, and allow the use of smaller ESR values. Capacitances less than 4.7 µF are not
recommended because they require careful selection of ESR to ensure stability. Solid tantalum electrolytic,
aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements
described above. Most of the commercially available 4.7 µF surface-mount solid tantalum capacitors, including
devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above. Multilayer ceramic
capacitors may have very small equivalent series resistances and may thus require the addition of a low value
series resistor to ensure stability.
CAPACITOR SELECTION
MFR.
VALUE
MAX ESR†
SIZE (H × L × W)†
T494B475K016AS
KEMET
4.7 µF
1.5 Ω
1.9 × 3.5 × 2.8
195D106x0016x2T
SPRAGUE
10 µF
1.5 Ω
1.3 × 7.0 × 2.7
695D106x003562T
SPRAGUE
10 µF
1.3 Ω
2.5 × 7.6 × 2.5
PART NO.
TPSC475K035R0600
AVX
4.7 µF
0.6 Ω
2.6 × 6.0 × 3.2
† Size is in mm. ESR is maximum resistance in Ohms at 100 kHz and TA = 25°C. Contact manufacturer for minimum ESR values.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
APPLICATION INFORMATION
output voltage programming
The output voltage of the TPS77001 adjustable regulator is programmed using an external resistor divider as
shown in Figure 22. The output voltage is calculated using:
V
O
ǒ) Ǔ
+ Vref
1
R1
R2
(1)
where
Vref = 1.224 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 169 kΩ to set the divider current at 7 µA and then calculate R1 using:
R1
+
ǒ Ǔ
V
V
O
ref
*1
(2)
R2
OUTPUT VOLTAGE
PROGRAMMING GUIDE
OUTPUT
VOLTAGE
(V)
TPS77001
DIVIDER RESISTANCE
(kΩ)‡
R1
R2
2.5
174
169
3.3
287
169
3.6
324
169
4.0
383
169
5.0
523
169
VI
1 µF
1
IN
OUT
≥ 1.7 V
3
VO
R1
EN
≤ 0.9 V
FB
GND
2
‡ 1% values shown.
5
4
4.7 µF
R2
ESR = 0.2 Ω
Figure 22. TPS77001 Adjustable LDO Regulator Programming
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TPS77001, TPS77012, TPS77015, TPS77018, TPS77025
TPS77027, TPS77028, TPS77030, TPS77033, TPS77050
ULTRALOW-POWER 50-mA LOW-DROPOUT LINEAR REGULATORS
SLVS210D – JUNE 1999 – REVISED MAY 2001
APPLICATION INFORMATION
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
T max * T
J
A
+
D(max)
R
qJA
Where:
TJmax is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table.
TA is the ambient temperature.
ǒ
Ǔ
The regulator dissipation is calculated using:
P
D
+ VI * VO
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
regulator protection
The TPS770xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might
be appropriate.
The TPS770xx features internal current limiting and thermal protection. During normal operation, the TPS770xx
limits output current to approximately 350 mA. When current limiting engages, the output voltage scales back
linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure,
care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device
exceeds approximately 165°C, thermal-protection circuitry shuts it down. Once the device has cooled down to
below approximately 140°C, regulator operation resumes.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS77001DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCPI
TPS77001DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCPI
TPS77001DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCPI
TPS77001DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCPI
TPS77012DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCQI
TPS77012DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCQI
TPS77012DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCQI
TPS77012DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCQI
TPS77015DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCRI
TPS77015DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCRI
TPS77015DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCRI
TPS77015DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCRI
TPS77018DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCSI
TPS77018DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCSI
TPS77018DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCSI
TPS77018DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCSI
TPS77025DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCTI
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
11-Apr-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS77025DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCTI
TPS77025DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCTI
TPS77025DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCTI
TPS77027DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCUI
TPS77027DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCUI
TPS77027DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCUI
TPS77027DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCUI
TPS77028DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCVI
TPS77028DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCVI
TPS77028DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCVI
TPS77028DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCVI
TPS77030DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCWI
TPS77030DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCWI
TPS77030DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCWI
TPS77030DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCWI
TPS77033DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
PCXI
TPS77033DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
PCXI
TPS77033DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
PCXI
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
11-Apr-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS77033DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
PCXI
TPS77050DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCYI
TPS77050DBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCYI
TPS77050DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCYI
TPS77050DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCYI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS77001, TPS77012, TPS77015, TPS77033 :
• Automotive: TPS77001-Q1, TPS77012-Q1, TPS77015-Q1, TPS77033-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TPS77001DBVR
SOT-23
DBV
5
3000
178.0
9.0
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
TPS77001DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77012DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS77012DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS77015DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77015DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77018DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77018DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77025DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77025DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77027DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77027DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77028DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77028DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77030DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77030DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77033DBVR
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS77033DBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TPS77050DBVR
SOT-23
DBV
5
3000
178.0
9.0
TPS77050DBVT
SOT-23
DBV
5
250
178.0
9.0
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
3.23
3.17
1.37
4.0
8.0
Q3
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS77001DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77001DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77012DBVR
SOT-23
DBV
5
3000
203.0
203.0
35.0
TPS77012DBVT
SOT-23
DBV
5
250
203.0
203.0
35.0
TPS77015DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77015DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77018DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77018DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77025DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77025DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77027DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77027DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77028DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77028DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77030DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS77030DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77033DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77033DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
TPS77050DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
TPS77050DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated