TI TPS76325QDBVRG4Q1

www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
D Qualified for Automotive Applications
D 150-mA Low-Dropout Regulator
D Output Voltage: 5 V, 3.8 V, 3.3 V, 3 V, 2.8 V,
D
D
D
D
D
D
DBV PACKAGE
(TOP VIEW)
2.7 V, 2.5 V, 1.8 V, 1.6 V and Variable
Dropout Voltage, Typically 300 mV
at 150 mA
Thermal Protection
Overcurrent Limitation
Less Than 2-µA Quiescent Current in
Shutdown Mode
−40°C to 125°C Operating Junction
Temperature Range
5-Pin SOT-23 (DBV) Package
IN
1
GND
2
EN
3
5
OUT
4
NC/FB
description
The TPS763xx family of low-dropout (LDO) voltage regulators offers the benefits of low-dropout voltage, low-power
operation, and miniaturized packaging. These regulators feature low dropout voltages and quiescent currents compared
to conventional LDO regulators. Offered in a 5-terminal, small outline integrated-circuit SOT-23 package, the TPS763xx
series devices are ideal for cost-sensitive designs and for applications where board space is at a premium.
A combination of new circuit design and process innovation has enabled the usual pnp pass transistor to be replaced by
a PMOS pass element. Because the PMOS pass element behaves as a low-value resistor, the dropout voltage is
low—typically 300 mV at 150 mA of load current (TPS76333)—and is directly proportional to the load current. Since the
PMOS pass element is a voltage-driven device, the quiescent current is low (140 µA maximum) and is stable over the entire
range of output load current (0 mA to 150 mA). Intended for use in portable systems such as laptops and cellular phones,
the low-dropout voltage feature and low-power operation result in a significant increase in system battery operating life.
The TPS763xx also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current to 1 µA
maximum at TJ = 25°C.The TPS763xx is offered in 1.6-V,1.8-V, 2.5-V, 2.7-V, 2.8-V, 3-V, 3.3-V, 3.8-V, and 5-V fixed-voltage
versions and in a variable version (programmable over the range of 1.5 V to 6.5 V).
TJ
AVAILABLE OPTIONS{
VOLTAGE
PACKAGE}
PART NUMBER
TPS76301QDBVRQ1
BAN
1.6 V
TPS76316QDBVRQ1
BAD
1.8 V
TPS76318QDBVRQ1
BAP
2.5 V
TPS76325QDBVRQ1
TPS76327QDBVRQ1§
BAQ
2.7 V
−40°C to 125°C
SYMBOL
Variable
2.8 V
SOT-23
(DBV)
TPS76328QDBVRQ1§
3V
TPS76330QDBVRQ1
BAT
3.3 V
TPS76333QDBVRQ1
TPS76338QDBVRQ1§
BAU
3.8 V
5.0 V
TPS76350QDBVRQ1
BAW
† For the most current package and ordering information, see the Package Option Addendum at
the end of this document, or see the TI web site at http://www.ti.com.
‡ Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
§ Product Preview. Contact Texas Instruments for availability.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
!"# $ %&!!'# "$ (&)*%"# +"#', !+&%#$
%! # $('%%"#$ ('! #-' #'!$ '."$ $#!&'#$ $#"+"!+ /"!!"#0,
!+&%# (!%'$$1 +'$ # '%'$$"!*0 %*&+' #'$#1 "** ("!"'#'!$,
Copyright  2008 Texas Instruments Incorporated
SGLS247A − JUNE 2004 − REVISED JUNE 2008
functional block diagram
TPS76301
OUT
IN
EN
Current Limit/
Thermal
Protection
VREF
FB
GND
TPS76316/ 18/ 25/ 27/ 28/ 30/ 33/ 38/ 50
OUT
IN
EN
Current Limit/
Thermal
Protection
VREF
GND
Terminal Functions
TERMINAL
DESCRIPTION
NAME
GND
Ground
EN
Enable input
FB
Feedback voltage (TPS76301 only)
IN
Input supply voltage
NC
No connection (fixed-voltage option only)
OUT
Regulated output voltage
2
www.ti.com
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
absolute maximum ratings over operating free-air temperature range (unless otherwise
noted)(1)
Input voltage range(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 10 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VI + 0.3 V
Voltage on OUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Tables
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = 25°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
Low K(1)
DBV
65.8°C/W
259°C/W
3.9 mW/°C
386 mW
212 mW
154 mW
High K(2)
DBV
65.8°C/W
180°C/W
5.6 mW/°C
555 mW
305 mW
222 mW
(1) The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the
board.
(2) The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground
planes and 2 ounce copper traces on top and bottom of the board.
recommended operating conditions
MIN
Input voltage, VI(1)
Continuous output current, IO
Operating junction temperature, TJ
(1) To calculate the minimum input voltage for your maximum output current, use the following equation:
VI(min) = VO(max) + VDO(max load)
NOM
MAX
UNIT
2.7
10
V
0
150
mA
−40
125
°C
3
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
3.25 V > VI ≥ 2.7 V,
2.5 V ≥ VO ≥ 1.5 V,
3.25 V > VI ≥ 2.7 V,
2.5 V ≥ VO ≥ 1.5 V
TPS76301
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI = 2.7 V,
VI = 2.7 V,
TPS76316
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 2.7 V,
VO
VI = 2.7 V,
Output voltage
TPS76318
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
IO = 1 mA to 100 mA,
TPS76325
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
TPS76327
TPS76328
TPS76330
IO = 1 mA to 100 mA,
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA,
1 mA< IO < 75 mA,
TJ = 25°C
1 mA< IO < 75 mA
1 mA < IO < 100 mA,
TJ = 25°C
1 mA < IO < 100 mA
1 mA < IO < 150 mA,
TJ = 25°C
1 mA < IO < 150 mA
1 mA< IO < 75 mA,
TJ = 25°C
1 mA< IO < 75 mA
1 mA < IO < 100 mA,
TJ = 25°C
1 mA < IO < 100 mA
1 mA < IO < 150 mA,
TJ = 25°C
1 mA < IO < 150 mA
TJ = 25°C
TJ = 25°C
TJ = 25°C
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
TJ = 25°C
TYP
MAX
0.98 VO
VO
1.02 VO
0.97 VO
VO
1.03 VO
0.98 VO
VO
1.02 VO
0.97 VO
VO
1.03 VO
0.975 VO
VO
1.025 VO
0.9625 VO
VO
1.0375 VO
1.568
1.6
1.632
1.552
1.6
1.648
1.568
1.6
1.632
1.552
1.6
1.648
1.56
1.6
1.640
1.536
1.6
1.664
1.764
1.8
1.836
1.746
1.8
1.854
1.764
1.8
1.836
1.746
1.8
1.854
1.755
1.8
1.845
1.733
1.8
1.867
2.45
2.5
2.55
2.425
2.5
2.575
2.438
2.5
2.562
2.407
2.5
2.593
2.646
2.7
2.754
2.619
2.7
2.781
2.632
2.7
2.767
2.599
2.7
2.801
2.744
2.8
2.856
2.716
2.8
2.884
2.73
2.8
2.87
UNIT
V
V
V
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
2.695
2.8
2.905
TJ = 25°C
2.94
3
3.06
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
2.91
3
3.09
TJ = 25°C
2.925
3
3.075
2.888
3
3.112
IO = 1 mA to 150 mA
4
IO = 1 mA to 75 mA,
TJ = 25°C
IO = 1 mA to 75 mA,
MIN
V
V
V
V
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TPS76333
VO
Output voltage
TPS76338
TPS76350
I(Q)
Quiescent current
(GND terminal current)
Standby current
Vn
Output noise voltage
PSRR
Ripple rejection
MIN
TYP
MAX
3.234
3.3
3.366
3.201
3.3
3.399
3.218
3.3
3.382
3.177
3.3
3.423
3.724
3.8
3.876
3.705
3.8
3.895
3.686
3.8
3.914
3.667
3.8
3.933
4.875
5
5.125
4.825
5
5.175
4.750
5
5.15
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
TJ = 25°C
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
TJ = 25°C
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
TJ = 25°C
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
TJ = 25°C
5
5.20
IO = 0 to 150 mA,
IO = 0 to 150 mA see (2)
TJ = 25°C (1)
85
100
EN < 0.5 V,
TJ = 25°C
0.5
4.80
140
EN < 0.5 V
Current limit
V
V
V
µA
A
2
BW = 300 Hz to 50 kHz,
TJ = 25°C,
Co = 10 µF (2)
f = 1 kHz, Co = 10 µF,
TJ = 25°C, see (3)
TJ = 25°C (2)
VI ≥ 3.5 V, TJ = 25°C
VI ≥ 3.5 V
VIH
VIL
EN high level input
VO + 1 V < VI ≤ 10 V,
VO + 1 V < VI ≤ 10 V,
See (2)
EN low level input
See (2)
II
EN input current
Output voltage line regulation
(∆VO/VO), (see (3))
1
UNIT
µV
140
60
0.5
dB
0.8
1.5
0.04
0.07
0.1
1.4
0.5
A
%/V
2
V
1.2
EN = 0 V
−0.01
−0.5
EN = IN
−0.01
−0.5
A
µA
(1) Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater.
(2) Test condition includes: output voltage VO = 0 V (for variable device FB is shorted to VO) and pulse duration = 10 ms.
(3) If VO < 2.5 V and VImax = 10 V, VImin = 3.5 V:
Line Reg. (mV) + ǒ%ńVǓ
V
O
100
If VO > 2.5 V and VImax = 10 V, VImin = VO + 1 V:
Line Reg. (mV) + ǒ%ńVǓ
ǒVImax * 3.5 VǓ
V
O
1000
ǒVImax * ǒVO ) 1ǓǓ
100
1000
5
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TPS76325
VDO
Dropout voltage
TPS76333
TPS76350
6
MIN
TYP
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
120
IO = 75 mA,
IO = 75 mA
TJ = 25°C
180
IO = 100 mA,
IO = 100 mA
TJ = 25°C
IO = 150 mA,
IO = 150 mA
TJ = 25°C
360
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
100
IO = 75 mA,
IO = 75 mA
TJ = 25°C
150
IO = 100 mA,
IO = 100 mA
TJ = 25°C
200
IO = 150 mA,
IO = 150 mA
TJ = 25°C
300
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
60
IO = 75 mA,
IO = 75 mA
TJ = 25°C
IO = 100 mA,
IO = 100 mA
TJ = 25°C
120
IO = 150 mA,
IO = 150 mA
TJ = 25°C
180
MAX
UNIT
3
150
200
225
300
240
mV
300
400
450
600
3
125
166
188
250
mV
250
333
375
500
2
75
100
90
113
150
150
200
225
300
mV
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
TPS76325
TPS76318
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
2.505
VI = 3.5 V
CI = CO = 4.7 µF
TJ = 25°C
1.800
VO − Output Voltage − V
2.5
VO − Output Voltage − V
1.805
VI = 3.5 V
CI = CO = 4.7 µF
TJ = 25°C
2.495
2.49
2.485
1.795
1.790
1.785
1.780
2.48
1.775
2.475
0
30
60
90
120
150
180
1.770
0
IO − Output Current − mA
30
60
Figure 1
120
150
180
Figure 2
TPS76350
TPS76325
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5.01
2.53
VI = 6 V
CI = CO = 4.7 µF
TJ = 25°C
VI = 3.5 V
CI = CO = 4.7 µF
2.52
VO − Output Voltage − V
5
VO− Output Voltage − V
90
IO − Output Current − mA
4.99
4.98
4.97
4.96
2.51
IO = 1 mA
2.5
2.49
IO = 150 mA
2.48
4.95
0
30
60
90
120
IO − Output Current − mA
Figure 3
150
180
2.47
−55 −35
−15
5
25
45
65
85
105
125
TJ − Junction Temperature − °C
Figure 4
7
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
TPS76318
TPS76350
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5.1
1.82
VI = 6 V
CI = CO = 4.7 µF
5.08
1.81
IO = 1 mA
5.06
VO − Output Voltage − V
VO − Output Voltage − V
1.8
1.79
IO = 150 mA
1.78
1.77
1.76
5.04
5.02
IO = 1 mA
5
4.98
4.96
IO = 150 mA
4.94
VI = 3.5 V
CI = CO = 4.7 µF
1.75
1.74
−55 −35
−15
5
25
45
65
85
105
4.92
125
4.9
−55 −35
TJ − Junction Temperature − °C
−15
25
5
45
85
65
105
125
TJ − Junction Temperature − °C
Figure 5
Figure 6
TPS76350
OUTPUT NOISE
vs
FREQUENCY
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
3 mV ǸHz
1000
TJ = 25°C
Ground Current − µ A
VI = 6 V
CI = CO = 4.7 µF
IO = 0 mA and 150 mA
2.5 mV ǸHz
2 mV ǸHz
1 mV ǸHz
10
−55 −35
CO = 4.7 µF
IO = 150 mA
1.5 mV ǸHz
100
0.5 mV ǸHz
−15
5
25
45
65
85
TJ − Junction Temperature − °C
Figure 7
8
CO = 10 µF
IO = 150 mA
105
125
0 mV ǸHz
250
CO = 4.7 µF
IO = 1 mA
CO = 10 µF
IO = 1 mA
1k
10k
f − Frequency − Hz
Figure 8
100k
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
TPS76325
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT IMPEDANCE
vs
FREQUENCY
600
10
VI = EN = 2.7 V
CI = CO = 4.7 µF
VDO − Dropout Voltage − mV
IO = 1 mA
1
IO = 150 mA
0.1
0.01
0.1
150 mA
400
300
200
1 mA
0 mA
100
CI = CO = 4.7 µF
ESR = 1 Ω
TJ = 25°C
1
10
100
0
−55 −35
1000
−15
5
25
45
65
85
105
125
TJ − Junction Temperature − °C
f − Frequency − kHz
Figure 9
Figure 10
TPS76325
RIPPLE REJECTION
vs
FREQUENCY
70
60
IO = 1 mA
50
Ripple Rejection − dB
Zo − Output Impedance − Ω
500
IO = 150 mA
40
30
20
10
0
−10
10
CO = 4.7 µF
ESR = 1 Ω
TJ = 25°C
100
1k
10 k
100 k
1M
10 M
f − Frequency − Hz
Figure 11
9
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
4
3
2
∆ VO − Change in
Output Voltage − mV
200
100
0
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
50
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
1
TPS76318
LOAD TRANSIENT RESPONSE
I O − Output Current − mA
5
20
0
dv + 1 V
10 ms
dt
−20
−30
∆ VO − Change in
Output Voltage − mV
VI − Input Voltage − V
TPS76318
LINE TRANSIENT RESPONSE
0
−50
−100
−150
0
20
40
60
0
80 100 120 140 160 180 200
t − Time − µs
20
40
8
dv + 1 V
10 ms
dt
6
5
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
∆ VO − Change in
Output Voltage − mV
50
0
−50
TPS76350
LOAD TRANSIENT RESPONSE
200
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
100
0
150
100
0
−100
−200
−100
0
50
100 150 200 250 300 350 400 450 500
t − Time − µs
Figure 14
10
I O − Output Current − mA
TPS76350
LINE TRANSIENT RESPONSE
7
80 100 120 140 160 180 200
t − Time − µs
Figure 13
∆ VO − Change in
Output Voltage − mV
VI − Input Voltage − V
Figure 12
60
0
20
40
60
80 100 120 140 160 180 200
t − Time − µs
Figure 15
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
TYPICAL REGIONS OF STABILITY
TYPICAL REGIONS OF STABILITY
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
OUTPUT CURRENT
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
ADDED CERAMIC CAPACITANCE
100
CSR − Compensation Series Resistance − Ω
CSR − Compensation Series Resistance − Ω
100
Region of Instability
10
CO = 4.7 µF
TJ = 25°C
1
0.1
Region of Instability
0.01
Region of Instability
10
I = 150 mA
CO = 4.7 µF
TJ = 25°C
1
0.1
Region of Instability
0.01
0
50
100
150
200
250
0
0.1
Figure 16
0.6 0.7 0.8
0.9
1
Figure 17
TYPICAL REGIONS OF STABILITY
TYPICAL REGIONS OF STABILITY
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
OUTPUT CURRENT
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
ADDED CERAMIC CAPACITANCE
100
CSR − Compensation Series Resistance − Ω
100
CSR − Compensation Series Resistance − Ω
0.2 0.3 0.4 0.5
Added Ceramic Capacitance − µF
IO − Output Current − mA
Region of Instability
10
CO = 10 µF
1
0.1
Region of Instability
0.01
0
50
100
150
IO − Output Current − mA
Figure 18
200
250
Region of Instability
10
CO = 10 µF
1
0.1
Region of Instability
0.01
0
0.1
0.2 0.3 0.4 0.5
0.6 0.7 0.8
0.9
1
Added Ceramic Capacitance − µF
Figure 19
(1) CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace
resistance to CO.
11
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
The TPS763xx low-dropout (LDO) regulators are new families of regulators which have been optimized for use in
battery-operated equipment and feature low dropout voltages, low quiescent current (140 µA), and an enable input to
reduce supply currents to less than 2 µA when the regulator is turned off.
device operation
The TPS763xx uses a PMOS pass element to dramatically reduce both dropout voltage and supply current over more
conventional PNP pass element LDO designs. The PMOS pass element is a voltage-controlled device that, unlike a PNP
transistor, does not require increased drive current as output current increases. Supply current in the TPS763xx is
essentially constant from no-load to maximum load.
Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device
switches into a constant-current mode at approximately 1 A; further load reduces the output voltage instead of increasing
the output current. The thermal protection shuts the regulator off if the junction temperature rises above 165°C. Recovery
is automatic when the junction temperature drops approximately 25°C below the high temperature trip point. The PMOS
pass element includes a back diode that safely conducts reverse current when the input voltage level drops below the output
voltage level.
A logic low on the enable input, EN shuts off the output and reduces the supply current to less than 2 µA. EN should be
tied high in applications where the shutdown feature is not used.
A typical application circuit is shown in Figure 20.
TPS763xx(1)
VI
C1
1 µF
1
IN
NC/FB
OUT
4
5
VO
3
EN
+
GND
2
4.7 µF
CSR = 1 Ω
(1) TPS76316, TPS76318, TPS76325, TPS76327, TPS76328,
TPS7630 TPS76333, TPS76338, TPS76350 (fixed-voltage options).
Figure 20. Typical Application Circuit
12
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
external capacitor requirements
Although not required, a 0.047 µF or larger ceramic bypass input capacitor, connected between IN and GND and located
close to the TPS763xx, is recommended to improve transient response and noise rejection. A higher-value electrolytic input
capacitor may be necessary if large, fast-rise-time load transients are anticipated and the device is located several inches
from the power source.
Like all low dropout regulators, the TPS763xx requires an output capacitor connected between OUT and GND to stabilize
the internal loop control. The minimum recommended capacitance value is 4.7 µF and the ESR (equivalent series
resistance) must be between 0.3 Ω and 10 Ω. Capacitor values of 4.7 µF or larger are acceptable, provided the ESR is less
than 10 Ω. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided
they meet the requirements described above. Most of the commercially available 4.7-µF surface-mount solid tantalum
capacitors, including devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above.
CAPACITOR SELECTION
MFR.
VALUE
MAX ESR(1)
SIZE (H  L  W)†
T494B475K016AS
KEMET
4.7 µF
1.5 Ω
1.9 × 3.5 × 2.8
195D106x0016x2T
SPRAGUE
10 µF
1.5 Ω
1.3 × 7.0 × 2.7
695D106x003562T
SPRAGUE
10 µF
1.3 Ω
2.5 × 7.6 × 2.5
PART NO.
TPSC475K035R0600
AVX
4.7 µF
0.6 Ω
2.6 × 6.0 × 3.2
(1) Size is in mm. ESR is maximum resistance in ohms at 100 kHz and TA = 25°C. Listings are sorted by height.
output voltage programming
The output voltage of the TPS76301 adjustable regulator is programmed using an external resistor divider as shown in
Figure 21. The output voltage is calculated using:
V
O
+ 0.995
V
ǒ1 ) R1
Ǔ
R2
ref
(1)
Where:
Vref = 1.192 V typ (the internal reference voltage)
0.995 is a constant used to center the load regulator (1%)
Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be used, but offer
no inherent advantage and waste more power. Higher values should be avoided as leakage currents at FB increase the
output voltage error. The recommended design procedure is to choose R2 = 169 kΩ to set the divider current at 7 µA and
then calculate R1 using:
R1 +
ǒ
V
0.995
O
V
Ǔ
*1
ref
R2
(2)
13
www.ti.com
SGLS247A − JUNE 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
TPS76301
OUTPUT VOLTAGE
PROGRAMMING GUIDE
DIVIDER RESISTANCE
(kΩ)(1)
OUTPUT
VOLTAGE
(V)
R1
R2
2.5
187
169
3.3
301
169
3.6
348
169
4
402
169
549
169
750
6.45
(1) 1% values shown.
169
5
VI
1 µF
≥2 V
1
IN
OUT
3
≤ 0.5 V
5
VO
R1
EN
FB
GND
2
4
+
R2
4.7 µF
CSR = 1 Ω
Figure 21. TPS76301 Adjustable LDO Regulator Programming
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature allowable
to avoid damaging the device is 150°C. This restriction limits the power dissipation the regulator can handle in any given
application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation,
PD(max) and the actual dissipation, PD, which must be less than or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
D(max)
T max * T
A
+ J
R
qJA
Where:
TJmax is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table.
TA is the ambient temperature.
The regulator dissipation is calculated using:
P
D
ǒ
Ǔ
+ V *V
I
O
I
O
Power dissipation resulting from quiescent current is negligible.
regulator protection
The TPS763xx pass element has a built-in back diode that safely conducts reverse currents when the input voltage drops
below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally
limited. If extended reverse voltage is anticipated, external limiting might be appropriate.
The TPS763xx also features internal current limiting and thermal protection. During normal operation, the TPS763xx limits
output current to approximately 800 mA. When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to
exceed the power dissipation ratings of the package. If the temperature of the device exceeds 165°C, thermal-protection
circuitry shuts it down. Once the device has cooled down to below 140°C, the regulator operation resumes.
14
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76301QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76316QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76316QDBVRQ1
ACTIVE
SOT-23
DBV
5
TPS76318QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76318QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76325QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
3000
Green (RoHS
& no Sb/Br)
TPS76325QDBVRQ1
ACTIVE
SOT-23
DBV
5
TPS76330QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
TBD
TBD
Call TI
Call TI
Samples
(Requires Login)
TPS76301QDBVRG4Q1
TBD
(3)
Call TI
Call TI
CU NIPDAU Level-1-260C-UNLIM
TPS76330QDBVRQ1
ACTIVE
SOT-23
DBV
5
TPS76333QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Call TI
Call TI
TPS76333QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76350QDBVRG4Q1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS76350QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS76301-Q1, TPS76316-Q1, TPS76318-Q1, TPS76325-Q1, TPS76330-Q1, TPS76333-Q1, TPS76350-Q1 :
• Catalog: TPS76301, TPS76316, TPS76318, TPS76325, TPS76330, TPS76333, TPS76350
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated