TECHNICAL DATA IN74HC192A Presettable BCD/Decade UP/DOWN Counter High-Performance Silicon-Gate CMOS The IN74HC192A is identical in pinout to the LS/ALS192. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The counter has two separate clock inputs, a Count Up Clock and Count Down Clock inputs. The direction of counting is determined by which input is clocked. The outputs change state synchronous with the LOW-to-HIGH transitions on the clock inputs. This counter may be preset by entering the desired data on the P0, P1, P2, P3 input. When the Parallel Load input is taken low the data is loaded independently of either clock input. This feature allows the counters to be used as devide-by-n by modifying the count lenght with the preset inputs. In addition the counter can also be cleared. This is accomplished by inputting a high on the Master Reset input. All 4 internal stages are set to low independently of either clock input.Both a Terminal Count Down (TCD) and Terminal Count Up (TCU) Outputs are provided to enable cascading of both up and down counting functions. The TCD output produces a negative going pulse when the counter underflows and TCU outputs a pulse when the counter overflows. The counter can be cascaded by connecting the TCU and TCD outputs of one device to the Count Up Clock and Count Down Clock inputs, respectively, of the next device. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION IN74HC192AN Plastic IN74HC192AD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM PIN 16 =VCC PIN 8 = GND Rev. 00 IN74HC192A MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin ±20 mA IOUT DC Output Current, per Pin ±25 mA ICC DC Supply Current, VCC and GND Pins ±50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 °C 260 °C VOUT IIN Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min Max Unit 2.0 6.0 V 0 VCC V -55 +125 °C 0 0 0 1000 500 400 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. Rev. 00 IN74HC192A DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions VIH Minimum High-Level Input Voltage VIL VOH V 25 °C to -55°C ≤85 °C ≤125 °C Unit VOUT=0.1 V or VCC-0.1 V IOUT≤ 20 µA 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V Maximum Low Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT ≤ 20 µA 2.0 4.5 6.0 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V Minimum High-Level Output Voltage VIN=VIH or VIL IOUT ≤ 20 µA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 VIN=VIH or VIL IOUT ≤ 4.0 mA IOUT ≤ 5.2 mA 4.5 6.0 0.26 0.26 0.33 0.33 0.4 0.4 VIN=VIH or VIL IOUT ≤ 4.0 mA IOUT ≤ 5.2 mA VOL Guaranteed Limit Maximum Low-Level Output Voltage VIN=VIH or VIL IOUT ≤ 20 µA V IIN Maximum Input Leakage Current VIN=VCC or GND 6.0 ±0.1 ±1.0 ±1.0 µA ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0µA 6.0 8.0 80 160 µA FUNCTION TABLE MR PL Inputs CPU H X L L L H L H L H L H X = don’t care X X H H Mode CPD X X H H Reset(Asyn.) Preset(Asyn.) No Count Count Up Count Down No Count The IN74HC192 can be preset to any state, but will not count beyond 9. If preset to state 10, 11, 12, 13, 14 or 15, it will follow the sequence 10, 11, 6: 12, 13, 4: 14, 15, 2 if counting Up, and follow the sequence 15, 14, 13, 12, 11, 10, 9 if counting Down. Logic equations For Terminal Count: TCU = Q0 • Q3 • CPU TCD = Q0 • Q1 • Q2 • Q3 • CPD Rev. 00 IN74HC192A AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=6.0 ns) VCC Symbol V 25 °C to -55°C ≤85°C ≤125°C Unit Minimum Clock Frequency (50% Duty Cycle) (Figures 1 and 6) 2.0 4.5 6.0 12 36 43 3.2 16 19 2.6 13 15 MHz tPLH, tPHL Maximum Propagation Delay, Clock to Q (Figures 1 and 6) 2.0 4.5 6.0 215 43 37 270 54 46 325 65 55 ns tPLH, tPHL Maximum Propagation Delay, PL to Q (Figures 3 and 6) 2.0 4.5 6.0 215 43 37 270 54 46 325 65 55 ns tPLH, tPHL Maximum Propagation Delay, Clock to Terminal Count (Figures 2 and 6) 2.0 4.5 6.0 125 25 21 155 31 26 190 38 32 ns tTLH, tTHL Maximum Output Transition Time,Any Output (Figures 1 and 6) 2.0 4.5 6.0 75 15 13 95 20 18 110 23 20 ns - 10 10 10 pF fmax CIN CPD Parameter Guaranteed Limit Maximum Input Capacitance Power Dissipation Capacitance (Per Package) Typical @25°C,VCC=5.0 V Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC 60 pF TIMING REQUIREMENTS (CL=50pF,Input tr=tf=6.0 ns) VCC Symbol Parameter Guaranteed Limit V 25 °C to -55°C ≤85°C ≤125°C Unit tsu Minimum Setup Time, Pn to PL (Figure 4) 2.0 4.5 6.0 100 20 18 125 35 22 150 30 26 ns th Minimum Hold Time, Pn to PL (Figure 4) 2.0 4.5 6.0 0 0 0 0 0 0 0 0 0 ns tw Minimum Pulse Width, Clock (Figure 1) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tw Minimum Pulse Width, PL (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 26 150 30 26 ns tw Minimum Pulse Width, MR (Figure 5) 2.0 4.5 6.0 100 20 17 125 25 26 150 30 26 ns Minimum Input Rise and Fall Times (Figure 1) 2.0 4.5 6.0 100 500 400 100 500 400 100 500 400 ns tr, tf Rev. 00 IN74HC192A Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Switching Waveforms Figure 5. Switching Waveforms Figure 6. Test Circuit Rev. 00 IN74HC192A TIMING DIAGRAM Rev. 00 IN74HC192A EXPANDED LOGIC DIAGRAM Rev. 00 IN74HC192A N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 9 16 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 B 1 8 5.33 C F L C D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 -T- SEATING PLANE N G K M H D J 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) Dimension, mm A 16 9 H B 1 G P 8 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. F M Symbol MIN MAX A 9.8 10 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.72 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 Rev. 00