TECHNICAL DATA KK74HC175A Quad D Flip-Flop with Common Clock and Reset High-Performance Silicon-Gate CMOS The KK74HC175A is identical in pinout to the LS/ALS175. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. This device consists of four D flip-flops with common Reset and Clock inputs, and separate D inputs. Reset (active-low) is asynchronous and occurs when a low level is applied to the Reset input. Information at a D input is transferred to the corresponding Q output on the next positivegoing edge of the Clock input. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION KK74HC175AN Plastic KK74HC175AD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs PIN 16=VCC PIN 8 = GND Outputs Reset Clock D Q Q L X X L H H H H L H L L H H L X no change X = Don’t care 1 KK74HC175A MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin ±20 mA IOUT DC Output Current, per Pin ±25 mA ICC DC Supply Current, VCC and GND Pins ±50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 °C 260 °C VOUT IIN Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min Max Unit 2.0 6.0 V 0 VCC V -55 +125 °C 0 0 0 1000 500 400 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK74HC175A DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions Guaranteed Limit V 25 °C to -55°C ≤85 °C ≤125 °C Unit VIH Minimum HighLevel Input Voltage VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢≤ 20 µA 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V VIL Maximum Low Level Input Voltage VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA 2.0 4.5 6.0 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V VOH Minimum HighLevel Output Voltage VIN=VIH or VIL ⎢IOUT⎢ ≤ 20 µA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 VIN= VIL or VIH ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA 4.5 6.0 0.26 0.26 0.33 0.33 0.4 0.4 VIN=VIH or VIL ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA VOL Maximum LowLevel Output Voltage VIN= VIL or VIH ⎢IOUT⎢ ≤ 20 µA V IIN Maximum Input Leakage Current VIN=VCC or GND 6.0 ±0.1 ±1.0 ±1.0 µA ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0µA 6.0 8.0 80 160 µA 3 KK74HC175A AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=6.0 ns) Guaranteed Limit VCC Symbol Parameter V 25 °C to -55°C ≤85°C ≤125°C Unit fmax Maximum Clock Frequency (50% Duty Cycle) (Figures 1 and 4) 2.0 4.5 6.0 6.0 30 35 4.8 24 28 4.0 20 24 MHz tPLH, tPHL Maximum Propagation Delay, Clock to Q or Q (Figures 1 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tPHL, tPLH Maximum Propagation Delay , Reset to Q or Q (Figures 2 and 4) 2.0 4.5 6.0 125 25 21 155 31 26 190 38 32 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 4) 2.0 4.5 6.0 75 15 13 95 19 16 110 22 19 ns - 10 10 10 pF CIN CPD Maximum Input Capacitance Power Dissipation Capacitance (Per Flip-Flop) Typical @25°C,VCC=5.0 V Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC 35 pF TIMING REQUIREMENTS (CL=50pF,Input tr=tf=6.0 ns) Guaranteed Limit VCC Symbol Parameter V 25 °C to -55°C ≤85°C ≤125°C Unit tSU Minimum Setup Time, Data to Clock (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns th Minimum Hold Time, Clock to Data (Figure 3) 2.0 4.5 6.0 3 3 3 3 3 3 3 3 3 ns trec Minimum Recovery Time, Reset Inactive to Clock (Figure 2) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tw Minimum Pulse Width, Clock (Figure 1) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns tw Minimum Pulse Width, Reset (Figure 2) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns tr, tf Maximum Input Rise and Fall Times (Figure 1) 2.0 4.5 6.0 1000 500 400 1000 500 400 1000 500 400 ns 4 KK74HC175A Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Test Circuit EXPANDED LOGIC DIAGRAM 5 KK74HC175A N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 9 16 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 B 1 8 5.33 C F L C D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 -T- SEATING PLANE N G K M H D J 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) Dimension, mm A 16 9 H B 1 G P 8 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. F M Symbol MIN MAX A 9.8 10 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.72 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 6