Intel® I/O Controller Hub 9 (ICH9) Family Datasheet – For the Intel® 82801IB ICH9, 82801IR ICH9R, 82801IH ICH9DH, 82801IO ICH9DO, 82801IBM ICH9M and 82801IEM ICH9M-E, and ICH9M-SFF ICH9-I/O Controller Hubs August 2008 Document Number: 316972-004 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. Legal Lines and Disclaimers Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Intel® I/O Controller Hub 9 (ICH9) Family chipset component may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. I2C is a two-wire communications bus/protocol developed by Philips. SMBus is a subset of the I2C bus/protocol and was developed by Intel. Implementations of the I2C bus/protocol may require licenses from various entities, including Philips Electronics N.V. and North American Philips Corporation. Intel® Active Management Technology requires the computer system to have an Intel® AMT-enabled chipset, network hardware and software, as well as connection with a power source and a corporate network connection. Setup requires configuration by the purchaser and may require scripting with the management console or further integration into existing security frameworks to enable certain functionality. It may also require modifications of implementation of new business processes. With regard to notebooks, Intel AMT may not be available or certain capabilities may be limited over a host OS-based VPN or when connecting wirelessly, on battery power, sleeping, hibernating or powered off. For more information, see www.intel.com/ technology/platform-technology/intel-amt/ Intel® Virtualization Technology requires a computer system with a processor, chipset, BIOS, virtual machine monitor (VMM) and for some uses, certain platform software enabled for it. Functionality, performance or other benefit will vary depending on hardware and software configurations and may require a BIOS update. Software applications may not be compatible with all operating systems. Please check with your application vendor. Intel, Intel SpeedStep, Intel Viiv, and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright ©2007–2008, Intel Corporation 2 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Contents 1 Introduction ............................................................................................................ 43 1.1 About This Document......................................................................................... 43 1.2 Overview ......................................................................................................... 47 1.2.1 Capability Overview ................................................................................ 49 1.3 Intel® ICH9 Family High-Level Component Differences ........................................... 54 2 Signal Description ................................................................................................... 55 2.1 Direct Media Interface (DMI) to Host Controller ..................................................... 58 2.2 PCI Express* .................................................................................................... 59 2.3 LAN Connect Interface ....................................................................................... 59 2.4 Gigabit LAN Connect Interface ............................................................................ 60 2.5 Firmware Hub Interface...................................................................................... 61 2.6 PCI Interface .................................................................................................... 62 2.7 Serial ATA Interface........................................................................................... 64 2.8 LPC Interface.................................................................................................... 67 2.9 Interrupt Interface ............................................................................................ 68 2.10 USB Interface ................................................................................................... 69 2.11 Power Management Interface.............................................................................. 71 2.12 Processor Interface............................................................................................ 74 2.13 SMBus Interface................................................................................................ 75 2.14 System Management Interface............................................................................ 76 2.15 Real Time Clock Interface ................................................................................... 78 2.16 Other Clocks..................................................................................................... 78 2.17 Miscellaneous Signals ........................................................................................ 78 2.18 Intel® High Definition Audio Link ......................................................................... 80 2.19 Serial Peripheral Interface (SPI) .......................................................................... 81 2.20 Controller Link .................................................................................................. 82 2.21 Intel® Quiet System Technology (Desktop Only) ................................................... 83 2.22 General Purpose I/O Signals ............................................................................... 83 2.23 Power and Ground Signals .................................................................................. 86 2.24 Pin Straps ........................................................................................................ 88 2.24.1 Functional Straps ................................................................................... 88 2.24.2 External RTC Circuitry ............................................................................. 90 3 Intel® ICH9 Pin States............................................................................................. 91 3.1 Integrated Pull-Ups and Pull-Downs ..................................................................... 91 3.2 Output and I/O Signals Planes and States............................................................. 92 3.3 Power Planes for Input Signals .......................................................................... 101 4 Intel® ICH9 and System Clock Domains................................................................. 107 5 Functional Description ........................................................................................... 109 5.1 DMI-to-PCI Bridge (D30:F0) ............................................................................. 109 5.1.1 PCI Bus Interface ................................................................................. 109 5.1.2 PCI Bridge As an Initiator ...................................................................... 109 5.1.2.1 Memory Reads and Writes........................................................ 110 5.1.2.2 I/O Reads and Writes .............................................................. 110 5.1.2.3 Configuration Reads and Writes ................................................ 110 5.1.2.4 Locked Cycles ........................................................................ 110 5.1.2.5 Target / Master Aborts............................................................. 110 5.1.2.6 Secondary Master Latency Timer............................................... 110 5.1.2.7 Dual Address Cycle (DAC) ........................................................ 110 5.1.2.8 Memory and I/O Decode to PCI................................................. 111 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 3 5.2 5.3 5.4 5.5 4 5.1.3 Parity Error Detection and Generation...................................................... 111 5.1.4 PCIRST# ............................................................................................. 112 5.1.5 Peer Cycles .......................................................................................... 112 5.1.6 PCI-to-PCI Bridge Model ........................................................................ 112 5.1.7 IDSEL to Device Number Mapping ........................................................... 113 5.1.8 Standard PCI Bus Configuration Mechanism.............................................. 113 PCI Express* Root Ports (D28:F0,F1,F2,F3,F4,F5) ................................................ 113 5.2.1 Interrupt Generation ............................................................................. 113 5.2.2 Power Management............................................................................... 114 5.2.2.1 S3/S4/S5 Support ................................................................... 114 5.2.2.2 Resuming from Suspended State ............................................... 114 5.2.2.3 Device Initiated PM_PME Message ............................................. 114 5.2.2.4 SMI/SCI Generation................................................................. 115 5.2.3 SERR# Generation ................................................................................ 115 5.2.4 Hot-Plug .............................................................................................. 116 5.2.4.1 Presence Detection .................................................................. 116 5.2.4.2 Message Generation ................................................................ 116 5.2.4.3 Attention Button Detection ....................................................... 117 5.2.4.4 SMI/SCI Generation................................................................. 117 Gigabit Ethernet Controller (B0:D25:F0) ............................................................. 117 5.3.1 Gigabit Ethernet PCI Bus Interface .......................................................... 118 5.3.1.1 Transaction Layer.................................................................... 118 5.3.1.2 Data Alignment ....................................................................... 118 5.3.1.3 Configuration Request Retry Status ........................................... 119 5.3.2 Error Events and Error Reporting ............................................................ 119 5.3.2.1 Data Parity Error ..................................................................... 119 5.3.2.2 Completion with Unsuccessful Completion Status ......................... 119 5.3.3 Ethernet Interface ................................................................................ 119 5.3.3.1 MAC/LAN Connect Interface ...................................................... 119 5.3.4 PCI Power Management ......................................................................... 120 5.3.4.1 Wake-Up................................................................................ 120 5.3.5 Configurable LEDs................................................................................. 121 5.3.6 Function Level Reset Support (FLR) ......................................................... 122 5.3.6.1 FLR Steps............................................................................... 122 LPC Bridge (w/ System and Management Functions) (D31:F0) ............................... 123 5.4.1 LPC Interface ....................................................................................... 123 5.4.1.1 LPC Cycle Types ...................................................................... 124 5.4.1.2 Start Field Definition ................................................................ 124 5.4.1.3 Cycle Type / Direction (CYCTYPE + DIR)..................................... 125 5.4.1.4 Size....................................................................................... 125 5.4.1.5 SYNC..................................................................................... 126 5.4.1.6 SYNC Time-Out ....................................................................... 126 5.4.1.7 SYNC Error Indication .............................................................. 126 5.4.1.8 LFRAME# Usage...................................................................... 127 5.4.1.9 I/O Cycles .............................................................................. 127 5.4.1.10 Bus Master Cycles ................................................................... 127 5.4.1.11 LPC Power Management ........................................................... 127 5.4.1.12 Configuration and Intel® ICH9 Implications................................. 128 DMA Operation (D31:F0) .................................................................................. 128 5.5.1 Channel Priority.................................................................................... 129 5.5.1.1 Fixed Priority .......................................................................... 129 5.5.1.2 Rotating Priority ...................................................................... 129 5.5.2 Address Compatibility Mode ................................................................... 129 5.5.3 Summary of DMA Transfer Sizes ............................................................. 130 5.5.3.1 Address Shifting When Programmed for 16-Bit I/O Count by Words 130 5.5.4 Autoinitialize ........................................................................................ 130 5.5.5 Software Commands ............................................................................. 131 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 5.6 5.7 5.8 5.9 5.10 LPC DMA ........................................................................................................ 131 5.6.1 Asserting DMA Requests........................................................................ 131 5.6.2 Abandoning DMA Requests .................................................................... 132 5.6.3 General Flow of DMA Transfers............................................................... 132 5.6.4 Terminal Count .................................................................................... 133 5.6.5 Verify Mode ......................................................................................... 133 5.6.6 DMA Request Deassertion...................................................................... 133 5.6.7 SYNC Field / LDRQ# Rules..................................................................... 134 8254 Timers (D31:F0) ..................................................................................... 135 5.7.1 Timer Programming .............................................................................. 135 5.7.2 Reading from the Interval Timer............................................................. 136 5.7.2.1 Simple Read........................................................................... 136 5.7.2.2 Counter Latch Command.......................................................... 137 5.7.2.3 Read Back Command .............................................................. 137 8259 Interrupt Controllers (PIC) (D31:F0) .......................................................... 138 5.8.1 Interrupt Handling................................................................................ 139 5.8.1.1 Generating Interrupts.............................................................. 139 5.8.1.2 Acknowledging Interrupts ........................................................ 139 5.8.1.3 Hardware/Software Interrupt Sequence ..................................... 140 5.8.2 Initialization Command Words (ICWx) ..................................................... 140 5.8.2.1 ICW1 .................................................................................... 140 5.8.2.2 ICW2 .................................................................................... 141 5.8.2.3 ICW3 .................................................................................... 141 5.8.2.4 ICW4 .................................................................................... 141 5.8.3 Operation Command Words (OCW) ......................................................... 141 5.8.4 Modes of Operation .............................................................................. 141 5.8.4.1 Fully Nested Mode................................................................... 141 5.8.4.2 Special Fully-Nested Mode........................................................ 142 5.8.4.3 Automatic Rotation Mode (Equal Priority Devices)........................ 142 5.8.4.4 Specific Rotation Mode (Specific Priority).................................... 142 5.8.4.5 Poll Mode............................................................................... 142 5.8.4.6 Cascade Mode ........................................................................ 143 5.8.4.7 Edge and Level Triggered Mode ................................................ 143 5.8.4.8 End of Interrupt (EOI) Operations ............................................. 143 5.8.4.9 Normal End of Interrupt........................................................... 143 5.8.4.10 Automatic End of Interrupt Mode .............................................. 143 5.8.5 Masking Interrupts ............................................................................... 144 5.8.5.1 Masking on an Individual Interrupt Request................................ 144 5.8.5.2 Special Mask Mode.................................................................. 144 5.8.6 Steering PCI Interrupts ......................................................................... 144 Advanced Programmable Interrupt Controller (APIC) (D31:F0) .............................. 145 5.9.1 Interrupt Handling................................................................................ 145 5.9.2 Interrupt Mapping ................................................................................ 145 5.9.3 PCI / PCI Express* Message-Based Interrupts .......................................... 146 5.9.4 Front Side Bus Interrupt Delivery ........................................................... 146 5.9.4.1 Edge-Triggered Operation ........................................................ 147 5.9.4.2 Level-Triggered Operation........................................................ 147 5.9.4.3 Registers Associated with Front Side Bus Interrupt Delivery.......... 147 5.9.4.4 Interrupt Message Format ........................................................ 147 5.9.5 IOxAPIC Address Remapping ................................................................. 148 5.9.6 External Interrupt Controller Support ...................................................... 148 Serial Interrupt (D31:F0) ................................................................................. 149 5.10.1 Start Frame......................................................................................... 149 5.10.2 Data Frames........................................................................................ 150 5.10.3 Stop Frame ......................................................................................... 150 5.10.4 Specific Interrupts Not Supported via SERIRQ .......................................... 150 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 5 5.11 5.12 5.13 6 5.10.5 Data Frame Format............................................................................... 151 Real Time Clock (D31:F0) ................................................................................. 152 5.11.1 Update Cycles ...................................................................................... 152 5.11.2 Interrupts ............................................................................................ 153 5.11.3 Lockable RAM Ranges............................................................................ 153 5.11.4 Century Rollover................................................................................... 153 5.11.5 Clearing Battery-Backed RTC RAM........................................................... 153 Processor Interface (D31:F0) ............................................................................ 155 5.12.1 Processor Interface Signals .................................................................... 155 5.12.1.1 A20M# (Mask A20).................................................................. 155 5.12.1.2 INIT# (Initialization)................................................................ 156 5.12.1.3 FERR#/IGNNE# (Numeric Coprocessor Error/ Ignore Numeric Error)........................................................................ 156 5.12.1.4 NMI (Non-Maskable Interrupt) .................................................. 157 5.12.1.5 Stop Clock Request (STPCLK#) ................................................. 157 5.12.1.6 CPU Power Good (CPUPWRGD).................................................. 157 5.12.1.7 Deeper Sleep (DPSLP#) (Mobile Only)........................................ 157 5.12.2 Dual-Processor Issues (Desktop Only) ..................................................... 158 5.12.2.1 Signal Differences ................................................................... 158 5.12.2.2 Power Management ................................................................. 158 Power Management (D31:F0) ............................................................................ 159 5.13.1 Features .............................................................................................. 159 5.13.2 Intel® ICH9 and System Power States ..................................................... 159 5.13.3 System Power Planes ............................................................................ 162 5.13.4 SMI#/SCI Generation ............................................................................ 162 5.13.4.1 PCI Express* SCI .................................................................... 165 5.13.4.2 PCI Express* Hot-Plug ............................................................. 165 5.13.5 Dynamic Processor Clock Control ............................................................ 165 5.13.5.1 Slow C4 and C5 Exit (Mobile Only)............................................. 166 5.13.5.2 Transition Rules among S0/Cx and Throttling States .................... 167 5.13.5.3 Deferred C3/C4 (Mobile Only) ................................................... 167 5.13.5.4 POPUP (Auto C3/C4 to C2) (Mobile Only) .................................... 167 5.13.5.5 POPDOWN (Auto C2 to C3/C4) (Mobile Only)............................... 168 5.13.5.6 C5 and C6 Entry/Exit (Mobile Only)............................................ 168 5.13.5.7 C5 Exit (Mobile Only) ............................................................... 168 5.13.6 Dynamic PCI Clock Control (Mobile Only) ................................................. 168 5.13.6.1 Conditions for Checking the PCI Clock ........................................ 169 5.13.6.2 Conditions for Maintaining the PCI Clock..................................... 169 5.13.6.3 Conditions for Stopping the PCI Clock ........................................ 169 5.13.6.4 Conditions for Re-Starting the PCI Clock..................................... 169 5.13.6.5 LPC Devices and CLKRUN# ....................................................... 169 5.13.7 Sleep States ........................................................................................ 170 5.13.7.1 Sleep State Overview............................................................... 170 5.13.7.2 Initiating Sleep State ............................................................... 170 5.13.7.3 Exiting Sleep States................................................................. 170 5.13.7.4 PCI Express* WAKE# Signal and PME Event Message ................... 172 5.13.7.5 Sx-G3-Sx, Handling Power Failures ............................................ 172 5.13.8 Thermal Management............................................................................ 173 5.13.8.1 THRM# Signal......................................................................... 173 5.13.8.2 Software Initiated Passive Cooling ............................................. 173 5.13.8.3 THRM# Override Software Bit ................................................... 174 5.13.8.4 Active Cooling......................................................................... 174 5.13.9 Event Input Signals and Their Usage ....................................................... 174 5.13.9.1 PWRBTN# (Power Button) ........................................................ 174 5.13.9.2 RI# (Ring Indicator) ................................................................ 175 5.13.9.3 PME# (PCI Power Management Event) ....................................... 176 5.13.9.4 SYS_RESET# Signal ................................................................ 176 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 5.14 5.15 5.16 5.13.9.5 THRMTRIP# Signal.................................................................. 176 5.13.10ALT Access Mode.................................................................................. 177 5.13.10.1Write Only Registers with Read Paths in ALT Access Mode ............ 178 5.13.10.2PIC Reserved Bits ................................................................... 180 5.13.10.3Read Only Registers with Write Paths in ALT Access Mode ............ 180 5.13.11System Power Supplies, Planes, and Signals ............................................ 181 5.13.11.1Power Plane Control with SLP_S3#, SLP_S4#, SLP_S5# and SLP_M# .......................................................................... 181 5.13.11.2SLP_S4# and Suspend-To-RAM Sequencing ............................... 181 5.13.11.3PWROK Signal ........................................................................ 182 5.13.11.4CPUPWRGD Signal .................................................................. 182 5.13.11.5VRMPWRGD Signal.................................................................. 182 5.13.11.6BATLOW# (Battery Low) (Mobile Only) ...................................... 182 5.13.12Clock Generators.................................................................................. 183 5.13.12.1Clock Control Signals from Intel® ICH9 to Clock Synthesizer (Mobile Only) ........................................................ 183 5.13.13Legacy Power Management Theory of Operation ....................................... 184 5.13.13.1APM Power Management (Desktop Only) .................................... 184 5.13.13.2Mobile APM Power Management (Mobile Only) ............................ 184 5.13.14Reset Behavior..................................................................................... 184 System Management (D31:F0).......................................................................... 186 5.14.1 Theory of Operation.............................................................................. 186 5.14.1.1 Detecting a System Lockup ...................................................... 186 5.14.1.2 Handling an Intruder ............................................................... 186 5.14.1.3 Detecting Improper Firmware Hub Programming ......................... 187 5.14.1.4 Heartbeat and Event Reporting via SMLink/SMBus....................... 187 5.14.2 TCO Modes .......................................................................................... 187 5.14.2.1 TCO Legacy/Compatible Mode .................................................. 187 5.14.2.2 Advanced TCO Mode ............................................................... 189 General Purpose I/O (D31:F0) .......................................................................... 190 5.15.1 Power Wells......................................................................................... 190 5.15.2 SMI# and SCI Routing .......................................................................... 190 5.15.3 Triggering ........................................................................................... 191 5.15.4 Serial POST Codes Over GPIO ................................................................ 191 5.15.4.1 Theory of operation................................................................. 191 5.15.4.2 Serial Message Format ............................................................ 192 5.15.5 Controller Link GPIOs (Digital Office Only) ............................................... 193 SATA Host Controller (D31:F2, F5) .................................................................... 193 5.16.1 SATA Feature Support........................................................................... 194 5.16.2 Theory of Operation.............................................................................. 195 5.16.2.1 Standard ATA Emulation .......................................................... 195 5.16.2.2 48-Bit LBA Operation............................................................... 195 5.16.3 SATA Swap Bay Support ....................................................................... 195 5.16.4 Hot Plug Operation ............................................................................... 195 5.16.4.1 Low Power Device Presence Detection ....................................... 195 5.16.5 Function Level Reset Support (FLR) ........................................................ 196 5.16.5.1 FLR Steps .............................................................................. 196 5.16.6 Intel® Matrix Storage Technology Configuration (Intel® ICH9R, ICH9DH, ICH9DO, ICH9M and ICH9M-E Only) ....................................................... 197 5.16.6.1 Intel® Matrix Storage Manager RAID Option ROM........................ 197 5.16.7 Power Management Operation................................................................ 198 5.16.7.1 Power State Mappings ............................................................. 198 5.16.7.2 Power State Transitions ........................................................... 199 5.16.7.3 SMI Trapping (APM) ................................................................ 200 5.16.8 SATA Device Presence........................................................................... 200 5.16.9 SATA LED............................................................................................ 200 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 7 5.17 5.18 5.19 8 5.16.10AHCI Operation .................................................................................... 201 5.16.11Serial ATA Reference Clock Low Power Request (SATACLKREQ#) ................ 201 5.16.12SGPIO Signals ...................................................................................... 201 5.16.12.1Mechanism ............................................................................. 202 5.16.12.2Message Format...................................................................... 202 5.16.12.3LED Message Type .................................................................. 203 5.16.12.4SGPIO Waveform .................................................................... 205 5.16.13External SATA ...................................................................................... 206 High Precision Event Timers .............................................................................. 206 5.17.1 Timer Accuracy .................................................................................... 206 5.17.2 Interrupt Mapping................................................................................. 206 5.17.3 Periodic vs. Non-Periodic Modes.............................................................. 207 5.17.4 Enabling the Timers .............................................................................. 208 5.17.5 Interrupt Levels.................................................................................... 208 5.17.6 Handling Interrupts............................................................................... 208 5.17.7 Issues Related to 64-Bit Timers with 32-Bit Processors .............................. 209 USB UHCI Host Controllers (D29:F0, F1, F2, F3 and D26:F0, F1 and F2) ................. 209 5.18.1 Data Structures in Main Memory ............................................................. 209 5.18.2 Data Transfers to/from Main Memory ...................................................... 209 5.18.3 Data Encoding and Bit Stuffing ............................................................... 210 5.18.4 Bus Protocol......................................................................................... 210 5.18.4.1 Bit Ordering............................................................................ 210 5.18.4.2 SYNC Field ............................................................................. 210 5.18.4.3 Packet Field Formats................................................................ 210 5.18.4.4 Address Fields......................................................................... 210 5.18.4.5 Frame Number Field ................................................................ 210 5.18.4.6 Data Field .............................................................................. 210 5.18.4.7 Cyclic Redundancy Check (CRC) ................................................ 210 5.18.5 Packet Formats .................................................................................... 210 5.18.6 USB Interrupts ..................................................................................... 211 5.18.6.1 Transaction-Based Interrupts .................................................... 211 5.18.6.2 Non-Transaction Based Interrupts ............................................. 213 5.18.7 USB Power Management ........................................................................ 213 5.18.8 USB Legacy Keyboard Operation ............................................................. 214 5.18.9 Function Level Reset Support (FLR) ......................................................... 216 5.18.9.1 FLR Steps............................................................................... 216 USB EHCI Host Controllers (D29:F7 and D26:F7) ................................................. 217 5.19.1 EHC Initialization .................................................................................. 217 5.19.1.1 BIOS Initialization ................................................................... 217 5.19.1.2 Driver Initialization .................................................................. 217 5.19.1.3 EHC Resets ............................................................................ 218 5.19.2 Data Structures in Main Memory ............................................................. 218 5.19.3 USB 2.0 Enhanced Host Controller DMA ................................................... 218 5.19.4 Data Encoding and Bit Stuffing ............................................................... 218 5.19.5 Packet Formats .................................................................................... 219 5.19.6 USB 2.0 Interrupts and Error Conditions .................................................. 219 5.19.6.1 Aborts on USB 2.0-Initiated Memory Reads................................. 219 5.19.7 USB 2.0 Power Management .................................................................. 220 5.19.7.1 Pause Feature......................................................................... 220 5.19.7.2 Suspend Feature ..................................................................... 220 5.19.7.3 ACPI Device States .................................................................. 220 5.19.7.4 ACPI System States................................................................. 221 5.19.7.5 Mobile Considerations .............................................................. 221 5.19.8 Interaction with UHCI Host Controllers..................................................... 221 5.19.8.1 Port-Routing Logic ................................................................... 222 5.19.8.2 Device Connects ..................................................................... 223 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 5.20 5.21 5.22 5.23 5.19.8.3 Device Disconnects ................................................................. 224 5.19.8.4 Effect of Resets on Port-Routing Logic........................................ 224 5.19.9 USB 2.0 Legacy Keyboard Operation ....................................................... 224 5.19.10USB 2.0 Based Debug Port .................................................................... 225 5.19.10.1 Theory of Operation ............................................................... 225 5.19.11USB Pre-Fetch Based Pause ................................................................... 229 5.19.12Function Level Reset Support (FLR) ........................................................ 230 5.19.12.1FLR Steps .............................................................................. 230 SMBus Controller (D31:F3) ............................................................................... 230 5.20.1 Host Controller..................................................................................... 231 5.20.1.1 Command Protocols ................................................................ 231 5.20.2 Bus Arbitration..................................................................................... 235 5.20.3 Bus Timing .......................................................................................... 235 5.20.3.1 Clock Stretching ..................................................................... 235 5.20.3.2 Bus Time Out (Intel® ICH9 as SMBus Master)............................. 235 5.20.4 Interrupts / SMI#................................................................................. 236 5.20.5 SMBALERT# ........................................................................................ 237 5.20.6 SMBus CRC Generation and Checking...................................................... 237 5.20.7 SMBus Slave Interface .......................................................................... 237 5.20.7.1 Format of Slave Write Cycle ..................................................... 238 5.20.7.2 Format of Read Command........................................................ 240 5.20.7.3 Slave Read of RTC Time Bytes .................................................. 242 5.20.7.4 Format of Host Notify Command ............................................... 243 Intel® High Definition Audio Overview ................................................................ 244 5.21.1 Intel® High Definition Audio Docking (Mobile Only) ................................... 244 5.21.1.1 Dock Sequence....................................................................... 244 5.21.1.2 Exiting D3/CRST# when Docked ............................................... 245 5.21.1.3 Cold Boot/Resume from S3 When Docked .................................. 246 5.21.1.4 Undock Sequence ................................................................... 246 5.21.1.5 Interaction Between Dock/Undock and Power Management States. 247 5.21.1.6 Relationship between HDA_DOCK_RST# and HDA_RST# ............. 247 5.21.2 Function Level Reset Support (FLR) ........................................................ 248 5.21.2.1 FLR Steps .............................................................................. 248 Intel® Active Management Technology (Intel® AMT) (Digital Office Only)................ 248 5.22.1 Intel® AMT Features ............................................................................. 249 5.22.2 Intel® AMT Requirements ...................................................................... 249 Serial Peripheral Interface (SPI) ........................................................................ 249 5.23.1 SPI Supported Feature Overview ............................................................ 249 5.23.1.1 Non-Descriptor Mode............................................................... 250 5.23.1.2 Descriptor Mode ..................................................................... 250 5.23.1.3 Device Partitioning .................................................................. 251 5.23.2 Flash Descriptor ................................................................................... 251 5.23.2.1 Descriptor Master Region ......................................................... 253 5.23.3 Flash Access ........................................................................................ 254 5.23.3.1 Direct Access Security ............................................................. 254 5.23.3.2 Register Access Security .......................................................... 254 5.23.4 Serial Flash Device Compatibility Requirements ........................................ 254 5.23.4.1 Intel® ICH9 SPI Based BIOS Requirements ................................ 255 5.23.4.2 Integrated LAN Firmware SPI Flash Requirements ....................... 255 5.23.4.3 Intel® Management Engine Firmware SPI Flash Requirements....... 255 5.23.4.4 Hardware Sequencing Requirements.......................................... 256 5.23.5 Multiple Page Write Usage Model ............................................................ 257 5.23.5.1 Soft Flash Protection ............................................................... 257 5.23.5.2 BIOS Range Write Protection .................................................... 257 5.23.5.3 SMI# Based Global Write Protection .......................................... 258 5.23.6 Flash Device Configurations ................................................................... 258 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 9 5.24 5.25 5.26 5.27 5.23.7 SPI Flash Device Recommended Pinout.................................................... 258 5.23.8 Serial Flash Device Package ................................................................... 259 5.23.8.1 Common Footprint Usage Model ................................................ 259 5.23.8.2 Serial Flash Device Package Recommendations ........................... 259 Intel® Quiet System Technology (Intel® QST) (Desktop Only) ............................... 260 5.24.1 PWM Outputs ....................................................................................... 260 5.24.2 TACH Inputs ........................................................................................ 260 Thermal Sensors.............................................................................................. 260 Feature Capability Mechanism ........................................................................... 261 Integrated Trusted Platform Module (Mobile Only) ................................................ 261 5.27.1 Integrated TPM Hardware Requirements .................................................. 261 5.27.2 Enabling integrated TPM ........................................................................ 261 6 Ballout Definition ................................................................................................... 263 6.1 Intel® ICH9 Ballout (Desktop Only) .................................................................... 263 6.2 Intel® 82801IBM ICH9M and 82801IEM ICH9M-E Ballout (Mobile Only) ................... 272 6.3 Intel® ICH9M-SFF Ballout (Mobile Only).............................................................. 281 7 Package Information ............................................................................................. 289 7.1 Intel® ICH9 Package (Desktop Only) .................................................................. 289 7.2 Intel® ICH9 Mobile Package (Mobile Only)........................................................... 291 7.2.1 Intel® 82801IBM ICH9M and 82801IEM ICH9M-E Package.......................... 291 7.2.2 Intel® ICH9M-SSF Package .................................................................... 293 8 Electrical Characteristics........................................................................................ 295 8.1 Thermal Specifications...................................................................................... 295 8.2 Absolute Maximum Ratings ............................................................................... 295 8.3 DC Characteristics ........................................................................................... 295 8.4 AC Characteristics............................................................................................ 308 8.5 Timing Diagrams ............................................................................................. 321 9 Register and Memory Mapping ............................................................................... 333 9.1 PCI Devices and Functions ................................................................................ 334 9.2 PCI Configuration Map ...................................................................................... 335 9.3 I/O Map.......................................................................................................... 335 9.3.1 Fixed I/O Address Ranges ...................................................................... 335 9.3.2 Variable I/O Decode Ranges ................................................................... 338 9.4 Memory Map ................................................................................................... 339 9.4.1 Boot-Block Update Scheme .................................................................... 340 10 Chipset Configuration Registers ............................................................................. 343 10.1 Chipset Configuration Registers (Memory Space) ................................................. 343 10.1.1 VCH—Virtual Channel Capability Header Register ...................................... 346 10.1.2 VCAP1—Virtual Channel Capability #1 Register ......................................... 346 10.1.3 VCAP2—Virtual Channel Capability #2 Register ......................................... 347 10.1.4 PVC—Port Virtual Channel Control Register............................................... 347 10.1.5 PVS—Port Virtual Channel Status Register................................................ 347 10.1.6 V0CAP—Virtual Channel 0 Resource Capability Register.............................. 348 10.1.7 V0CTL—Virtual Channel 0 Resource Control Register ................................. 349 10.1.8 V0STS—Virtual Channel 0 Resource Status Register .................................. 349 10.1.9 V1CAP—Virtual Channel 1 Resource Capability Register.............................. 350 10.1.10V1CTL—Virtual Channel 1 Resource Control Register ................................. 350 10.1.11V1STS—Virtual Channel 1 Resource Status Register .................................. 351 10.1.12PAT—Port Arbitration Table .................................................................... 351 10.1.13CIR1—Chipset Initialization Register 1 ..................................................... 352 10.1.14REC—Root Error Command Register ........................................................ 352 10.1.15RCTCL—Root Complex Topology Capabilities List Register .......................... 352 10 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 10.1.16ESD—Element Self Description Register................................................... 353 10.1.17ULD—Upstream Link Descriptor Register ................................................. 353 10.1.18ULBA—Upstream Link Base Address Register ........................................... 353 10.1.19RP1D—Root Port 1 Descriptor Register .................................................... 354 10.1.20RP1BA—Root Port 1 Base Address Register .............................................. 354 10.1.21RP2D—Root Port 2 Descriptor Register .................................................... 354 10.1.22RP2BA—Root Port 2 Base Address Register .............................................. 355 10.1.23RP3D—Root Port 3 Descriptor Register .................................................... 355 10.1.24RP3BA—Root Port 3 Base Address Register .............................................. 355 10.1.25RP4D—Root Port 4 Descriptor Register .................................................... 356 10.1.26RP4BA—Root Port 4 Base Address Register .............................................. 356 10.1.27HDD—Intel® High Definition Audio Descriptor Register .............................. 356 10.1.28HDBA—Intel® High Definition Audio Base Address Register ........................ 357 10.1.29RP5D—Root Port 5 Descriptor Register .................................................... 357 10.1.30RP5BA—Root Port 5 Base Address Register .............................................. 357 10.1.31RP6D—Root Port 6 Descriptor Register .................................................... 358 10.1.32RP6BA—Root Port 6 Base Address Register .............................................. 358 10.1.33ILCL—Internal Link Capabilities List Register ............................................ 358 10.1.34LCAP—Link Capabilities Register ............................................................. 359 10.1.35LCTL—Link Control Register ................................................................... 359 10.1.36LSTS—Link Status Register .................................................................... 359 10.1.37CIR2 — Chipset Initialization Register 2................................................... 360 10.1.38CIR3 — Chipset Initialization Register 3................................................... 360 10.1.39BCR — Backbone Configuration Register.................................................. 360 10.1.40RPC—Root Port Configuration Register .................................................... 361 10.1.41DMIC—DMI Control Register .................................................................. 362 10.1.42RPFN—Root Port Function Number and Hide for PCI Express* Root Ports ..... 362 10.1.43FLRSTAT—FLR Pending Status Register ................................................... 363 10.1.44CIR13—Chipset Initialization Register 13 ................................................. 364 10.1.45CIR5—Chipset Initialization Register 5..................................................... 364 10.1.46TRSR—Trap Status Register ................................................................... 364 10.1.47TRCR—Trapped Cycle Register ............................................................... 365 10.1.48TWDR—Trapped Write Data Register....................................................... 365 10.1.49IOTRn — I/O Trap Register (0-3)............................................................ 366 10.1.50DMC—DMI Miscellaneous Control Register ............................................... 367 10.1.51CIR6—Chipset Initialization Register 6..................................................... 367 10.1.52CIR7—Chipset Initialization Register 7..................................................... 368 10.1.53CIR11—Chipset Initialization Register 11 (Mobile Only).............................. 368 10.1.54CIR12—Chipset Initialization Register 12 (Mobile Only).............................. 368 10.1.55TCTL—TCO Configuration Register .......................................................... 369 10.1.56D31IP—Device 31 Interrupt Pin Register.................................................. 369 10.1.57D30IP—Device 30 Interrupt Pin Register.................................................. 370 10.1.58D29IP—Device 29 Interrupt Pin Register.................................................. 371 10.1.59D28IP—Device 28 Interrupt Pin Register.................................................. 372 10.1.60D27IP—Device 27 Interrupt Pin Register.................................................. 373 10.1.61D26IP—Device 26 Interrupt Pin Register.................................................. 374 10.1.62D25IP—Device 25 Interrupt Pin Register.................................................. 375 10.1.63D31IR—Device 31 Interrupt Route Register ............................................. 375 10.1.64D30IR—Device 30 Interrupt Route Register ............................................. 376 10.1.65D29IR—Device 29 Interrupt Route Register ............................................. 377 10.1.66D28IR—Device 28 Interrupt Route Register ............................................. 378 10.1.67D27IR—Device 27 Interrupt Route Register ............................................. 379 10.1.68D26IR—Device 26 Interrupt Route Register ............................................. 380 10.1.69D25IR—Device 25 Interrupt Route Register ............................................. 381 10.1.70OIC—Other Interrupt Control Register ..................................................... 382 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 11 10.1.71SBEMC3—Scheduled Break Event C3 Exit Latency (Mobile Only).................. 382 10.1.72SBEMC4—Scheduled Break Event C4 Exit Latency (Mobile Only).................. 383 10.1.73RC—RTC Configuration Register .............................................................. 383 10.1.74HPTC—High Precision Timer Configuration Register ................................... 384 10.1.75GCS—General Control and Status Register ............................................... 385 10.1.76BUC—Backed Up Control Register ........................................................... 387 10.1.77FD—Function Disable Register ................................................................ 388 10.1.78CG—Clock Gating.................................................................................. 390 10.1.79FDSW—Function Disable SUS Well .......................................................... 392 10.1.80CIR8—Chipset Initialization Register 8 ..................................................... 392 10.1.81CIR9—Chipset Initialization Register 9 ..................................................... 392 10.1.82PPO - Port Power Off ............................................................................. 392 10.1.83CIR10 - Chipset Initialization Register 10 ................................................. 393 10.1.84MAP - Remap Control Register ................................................................ 393 11 PCI-to-PCI Bridge Registers (D30:F0).................................................................... 395 11.1 PCI Configuration Registers (D30:F0) ................................................................. 395 11.1.1 VID— Vendor Identification Register (PCI-PCI—D30:F0)............................. 396 11.1.2 DID— Device Identification Register (PCI-PCI—D30:F0) ............................. 396 11.1.3 PCICMD—PCI Command (PCI-PCI—D30:F0) ............................................. 397 11.1.4 PSTS—PCI Status Register (PCI-PCI—D30:F0) .......................................... 397 11.1.5 RID—Revision Identification Register (PCI-PCI—D30:F0) ............................ 399 11.1.6 CC—Class Code Register (PCI-PCI—D30:F0)............................................. 399 11.1.7 PMLT—Primary Master Latency Timer Register (PCI-PCI—D30:F0) ............... 400 11.1.8 HEADTYP—Header Type Register (PCI-PCI—D30:F0) ................................. 400 11.1.9 BNUM—Bus Number Register (PCI-PCI—D30:F0) ...................................... 400 11.1.10SMLT—Secondary Master Latency Timer Register (PCI-PCI—D30:F0) ........... 401 11.1.11IOBASE_LIMIT—I/O Base and Limit Register (PCI-PCI—D30:F0) ................. 401 11.1.12SECSTS—Secondary Status Register (PCI-PCI—D30:F0) ............................ 402 11.1.13MEMBASE_LIMIT—Memory Base and Limit Register (PCI-PCI—D30:F0)................................................................................ 403 11.1.14PREF_MEM_BASE_LIMIT—Prefetchable Memory Base and Limit Register (PCI-PCI—D30:F0) ..................................................... 403 11.1.15PMBU32—Prefetchable Memory Base Upper 32 Bits Register (PCI-PCI—D30:F0) ................................................................... 404 11.1.16PMLU32—Prefetchable Memory Limit Upper 32 Bits Register (PCI-PCI—D30:F0) ................................................................... 404 11.1.17CAPP—Capability List Pointer Register (PCI-PCI—D30:F0) .......................... 404 11.1.18INTR—Interrupt Information Register (PCI-PCI—D30:F0) ........................... 404 11.1.19BCTRL—Bridge Control Register (PCI-PCI—D30:F0) ................................... 405 11.1.20SPDH—Secondary PCI Device Hiding Register (PCI-PCI—D30:F0) ................ 406 11.1.21DTC—Delayed Transaction Control Register (PCI-PCI—D30:F0) ................... 407 11.1.22BPS—Bridge Proprietary Status Register (PCI-PCI—D30:F0) ....................... 408 11.1.23BPC—Bridge Policy Configuration Register (PCI-PCI—D30:F0) ..................... 409 11.1.24SVCAP—Subsystem Vendor Capability Register (PCI-PCI—D30:F0) .............. 410 11.1.25SVID—Subsystem Vendor IDs Register (PCI-PCI—D30:F0) ......................... 410 12 Gigabit LAN Configuration Registers ...................................................................... 411 12.1 Gigabit LAN Configuration Registers (Gigabit LAN — D25:F0)................................. 411 12.1.1 VID—Vendor Identification Register (Gigabit LAN—D25:F0) .......................................................................... 412 12.1.2 DID—Device Identification Register (Gigabit LAN—D25:F0) .......................................................................... 412 12.1.3 PCICMD—PCI Command Register (Gigabit LAN—D25:F0) .......................................................................... 413 12 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 12.2 12.1.4 PCISTS—PCI Status Register (Gigabit LAN—D25:F0).......................................................................... 414 12.1.5 RID—Revision Identification Register (Gigabit LAN—D25:F0).......................................................................... 415 12.1.6 CC—Class Code Register (Gigabit LAN—D25:F0).......................................................................... 415 12.1.7 CLS—Cache Line Size Register (Gigabit LAN—D25:F0).......................................................................... 415 12.1.8 PLT—Primary Latency Timer Register (Gigabit LAN—D25:F0).......................................................................... 415 12.1.9 HT—Header Type Register (Gigabit LAN—D25:F0).......................................................................... 415 12.1.10MBARA—Memory Base Address Register A (Gigabit LAN—D25:F0).......................................................................... 416 12.1.11MBARB—Memory Base Address Register B (Gigabit LAN—D25:F0).......................................................................... 416 12.1.12MBARC—Memory Base Address Register C (Gigabit LAN—D25:F0).......................................................................... 417 12.1.13SVID—Subsystem Vendor ID Register (Gigabit LAN—D25:F0).......................................................................... 417 12.1.14SID—Subsystem ID Register (Gigabit LAN—D25:F0).......................................................................... 417 12.1.15ERBA—Expansion ROM Base Address Register (Gigabit LAN—D25:F0).......................................................................... 417 12.1.16CAPP—Capabilities List Pointer Register (Gigabit LAN—D25:F0).......................................................................... 418 12.1.17INTR—Interrupt Information Register (Gigabit LAN—D25:F0).......................................................................... 418 12.1.18MLMG—Maximum Latency/Minimum Grant Register (Gigabit LAN—D25:F0).......................................................................... 418 12.1.19CLIST 1—Capabilities List Register 1 (Gigabit LAN—D25:F0).......................................................................... 418 12.1.20PMC—PCI Power Management Capabilities Register (Gigabit LAN—D25:F0).......................................................................... 419 12.1.21PMCS—PCI Power Management Control and Status Register (Gigabit LAN—D25:F0) ............................................................. 420 12.1.22DR—Data Register (Gigabit LAN—D25:F0).......................................................................... 421 12.1.23CLIST 2—Capabilities List Register 2 (Gigabit LAN—D25:F0).......................................................................... 421 12.1.24MCTL—Message Control Register (Gigabit LAN—D25:F0).......................................................................... 421 12.1.25MADDL—Message Address Low Register (Gigabit LAN—D25:F0).......................................................................... 422 12.1.26MADDH—Message Address High Register (Gigabit LAN—D25:F0).......................................................................... 422 12.1.27MDAT—Message Data Register (Gigabit LAN—D25:F0).......................................................................... 422 12.1.28FLRCAP—Function Level Reset Capability (Gigabit LAN—D25:F0).......................................................................... 422 12.1.29FLRCLV—Function Level Reset Capability Length and Version (Gigabit LAN—D25:F0).......................................................................... 423 12.1.30DEVCTRL—Device Control (Gigabit LAN—D25:F0) ..................................... 423 MBARA—Gigabit LAN Base Address A Registers ................................................... 424 12.2.1 LDR4—LAN Device Initialization Register 4 (Gigabit LAN Memory Mapped Base Address Register) ............................... 424 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 13 12.2.2 LDR3—LAN Device Initialization Register 3 (Gigabit LAN Memory Mapped Base Address 12.2.3 LDCR2—LAN Device Control Register 2 (Gigabit LAN Memory Mapped Base Address 12.2.4 LDCR4—LAN Device Control Register 4 (Gigabit LAN Memory Mapped Base Address 12.2.5 LDR5—LAN Device Control Register 5 (Gigabit LAN Memory Mapped Base Address 12.2.6 LDR2—LAN Device Initialization Register 1 (Gigabit LAN Memory Mapped Base Address 13 14 Register) ............................... 424 Register) ............................... 425 Register) ............................... 425 Register) ............................... 425 Register) ............................... 425 LPC Interface Bridge Registers (D31:F0) ............................................................... 427 13.1 PCI Configuration Registers (LPC I/F—D31:F0) .................................................... 427 13.1.1 VID—Vendor Identification Register (LPC I/F—D31:F0) .............................. 428 13.1.2 DID—Device Identification Register (LPC I/F—D31:F0)............................... 428 13.1.3 PCICMD—PCI COMMAND Register (LPC I/F—D31:F0)................................. 429 13.1.4 PCISTS—PCI Status Register (LPC I/F—D31:F0)........................................ 430 13.1.5 RID—Revision Identification Register (LPC I/F—D31:F0) ............................ 431 13.1.6 PI—Programming Interface Register (LPC I/F—D31:F0) ............................. 431 13.1.7 SCC—Sub Class Code Register (LPC I/F—D31:F0) ..................................... 431 13.1.8 BCC—Base Class Code Register (LPC I/F—D31:F0) .................................... 431 13.1.9 PLT—Primary Latency Timer Register (LPC I/F—D31:F0) ............................ 431 13.1.10HEADTYP—Header Type Register (LPC I/F—D31:F0) .................................. 432 13.1.11SS—Sub System Identifiers Register (LPC I/F—D31:F0) ............................. 432 13.1.12CAPP—Capability List Pointer (LPC I/F—D31:F0) ....................................... 432 13.1.13PMBASE—ACPI Base Address Register (LPC I/F—D31:F0)........................... 432 13.1.14ACPI_CNTL—ACPI Control Register (LPC I/F — D31:F0) ............................. 433 13.1.15GPIOBASE—GPIO Base Address Register (LPC I/F — D31:F0) ..................... 434 13.1.16GC—GPIO Control Register (LPC I/F — D31:F0) ........................................ 435 13.1.17PIRQ[n]_ROUT—PIRQ[A,B,C,D] Routing Control Register (LPC I/F—D31:F0) ................................................................................ 436 13.1.18SIRQ_CNTL—Serial IRQ Control Register (LPC I/F—D31:F0) ................................................................................ 437 13.1.19PIRQ[n]_ROUT—PIRQ[E,F,G,H] Routing Control Register (LPC I/F—D31:F0) ................................................................................ 438 13.1.20LPC_IBDF—IOxAPIC Bus:Device:Function (LPC I/F—D31:F0) ................................................................................ 439 13.1.21LPC_I/O_DEC—I/O Decode Ranges Register (LPC I/F—D31:F0) ................................................................................ 439 13.1.22LPC_EN—LPC I/F Enables Register (LPC I/F—D31:F0) ................................ 440 13.1.23GEN1_DEC—LPC I/F Generic Decode Range 1 Register (LPC I/F—D31:F0) ................................................................................ 441 13.1.24GEN2_DEC—LPC I/F Generic Decode Range 2 Register (LPC I/F—D31:F0) ................................................................................ 442 13.1.25GEN3_DEC—LPC I/F Generic Decode Range 3 Register (LPC I/F—D31:F0) ................................................................................ 442 13.1.26GEN4_DEC—LPC I/F Generic Decode Range 4 Register (LPC I/F—D31:F0) ................................................................................ 443 13.1.27FWH_SEL1—Firmware Hub Select 1 Register (LPC I/F—D31:F0) ................................................................................ 444 13.1.28FWH_SEL2—Firmware Hub Select 2 Register (LPC I/F—D31:F0) ................................................................................ 445 13.1.29FWH_DEC_EN1—Firmware Hub Decode Enable Register (LPC I/F—D31:F0) ................................................................................ 445 13.1.30BIOS_CNTL—BIOS Control Register (LPC I/F—D31:F0) ................................................................................ 449 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 13.2 13.3 13.4 13.1.31FDCAP—Feature Detection Capability ID (LPC I/F—D31:F0) ................................................................................ 450 13.1.32FDLEN—Feature Detection Capability Length (LPC I/F—D31:F0) ................................................................................ 450 13.1.33FDVER—Feature Detection Version (LPC I/F—D31:F0) ................................................................................ 450 13.1.34FDVCT—Feature Vector (LPC I/F—D31:F0) ................................................................................ 451 13.1.35RCBA—Root Complex Base Address Register (LPC I/F—D31:F0) ................................................................................ 451 DMA I/O Registers (LPC I/F—D31:F0) ................................................................ 452 13.2.1 DMABASE_CA—DMA Base and Current Address Registers (LPC I/F—D31:F0) .................................................................. 453 13.2.2 DMABASE_CC—DMA Base and Current Count Registers (LPC I/F—D31:F0) ................................................................................ 454 13.2.3 DMAMEM_LP—DMA Memory Low Page Registers (LPC I/F—D31:F0) ................................................................................ 454 13.2.4 DMACMD—DMA Command Register (LPC I/F—D31:F0) .............................. 455 13.2.5 DMASTA—DMA Status Register (LPC I/F—D31:F0) .................................... 455 13.2.6 DMA_WRSMSK—DMA Write Single Mask Register (LPC I/F—D31:F0) ................................................................................ 456 13.2.7 DMACH_MODE—DMA Channel Mode Register (LPC I/F—D31:F0) ................................................................................ 457 13.2.8 DMA Clear Byte Pointer Register (LPC I/F—D31:F0) .................................. 458 13.2.9 DMA Master Clear Register (LPC I/F—D31:F0) .......................................... 458 13.2.10DMA_CLMSK—DMA Clear Mask Register (LPC I/F—D31:F0) ........................ 458 13.2.11DMA_WRMSK—DMA Write All Mask Register (LPC I/F—D31:F0) ................................................................................ 459 Timer I/O Registers (LPC I/F—D31:F0)............................................................... 460 13.3.1 TCW—Timer Control Word Register (LPC I/F—D31:F0) .............................. 461 13.3.2 RDBK_CMD—Read Back Command (LPC I/F—D31:F0)............................... 462 13.3.3 SBYTE_FMT—Interval Timer Status Byte Format Register (LPC I/F—D31:F0) ................................................................................ 463 13.3.4 Counter Access Ports Register (LPC I/F—D31:F0) ..................................... 464 8259 Interrupt Controller (PIC) Registers (LPC I/F—D31:F0) ........................................................................................... 465 13.4.1 Interrupt Controller I/O MAP (LPC I/F—D31:F0) ....................................... 465 13.4.2 ICW1—Initialization Command Word 1 Register (LPC I/F—D31:F0) ................................................................................ 466 13.4.3 ICW2—Initialization Command Word 2 Register (LPC I/F—D31:F0) ................................................................................ 467 13.4.4 ICW3—Master Controller Initialization Command Word 3 Register (LPC I/F—D31:F0)......................................................... 468 13.4.5 ICW3—Slave Controller Initialization Command Word 3 Register (LPC I/F—D31:F0)......................................................... 468 13.4.6 ICW4—Initialization Command Word 4 Register (LPC I/F—D31:F0) ................................................................................ 469 13.4.7 OCW1—Operational Control Word 1 (Interrupt Mask) Register (LPC I/F—D31:F0).................................................................... 469 13.4.8 OCW2—Operational Control Word 2 Register (LPC I/F—D31:F0) ................................................................................ 470 13.4.9 OCW3—Operational Control Word 3 Register (LPC I/F—D31:F0) ................................................................................ 471 13.4.10ELCR1—Master Controller Edge/Level Triggered Register (LPC I/F—D31:F0) ................................................................................ 472 13.4.11ELCR2—Slave Controller Edge/Level Triggered Register (LPC I/F—D31:F0) ................................................................................ 473 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 15 13.5 13.6 13.7 13.8 16 Advanced Programmable Interrupt Controller (APIC)(D31:F0)................................ 474 13.5.1 APIC Register Map (LPC I/F—D31:F0)...................................................... 474 13.5.2 IND—Index Register (LPC I/F—D31:F0) ................................................... 474 13.5.3 DAT—Data Register (LPC I/F—D31:F0) .................................................... 475 13.5.4 EOIR—EOI Register (LPC I/F—D31:F0) .................................................... 475 13.5.5 ID—Identification Register (LPC I/F—D31:F0) ........................................... 476 13.5.6 VER—Version Register (LPC I/F—D31:F0) ................................................ 476 13.5.7 REDIR_TBL—Redirection Table (LPC I/F—D31:F0) ..................................... 477 Real Time Clock Registers ................................................................................. 479 13.6.1 I/O Register Address Map ...................................................................... 479 13.6.2 Indexed Registers ................................................................................. 480 13.6.2.1 RTC_REGA—Register A ............................................................ 481 13.6.2.2 RTC_REGB—Register B (General Configuration)........................... 482 13.6.2.3 RTC_REGC—Register C (Flag Register) ....................................... 483 13.6.2.4 RTC_REGD—Register D (Flag Register)....................................... 483 Processor Interface Registers (LPC I/F—D31:F0) .................................................. 484 13.7.1 NMI_SC—NMI Status and Control Register (LPC I/F—D31:F0) ................................................................................ 484 13.7.2 NMI_EN—NMI Enable (and Real Time Clock Index) Register (LPC I/F—D31:F0) .................................................................... 485 13.7.3 PORT92—Fast A20 and Init Register (LPC I/F—D31:F0) ............................. 485 13.7.4 COPROC_ERR—Coprocessor Error Register (LPC I/F—D31:F0) ................................................................................ 486 13.7.5 RST_CNT—Reset Control Register (LPC I/F—D31:F0)................................. 486 Power Management Registers (PM—D31:F0) ....................................................... 487 13.8.1 Power Management PCI Configuration Registers (PM—D31:F0) ...................................................................................... 487 13.8.1.1 GEN_PMCON_1—General PM Configuration 1 Register (PM—D31:F0) ......................................................................... 488 13.8.1.2 GEN_PMCON_2—General PM Configuration 2 Register (PM—D31:F0) ......................................................................... 490 13.8.1.3 GEN_PMCON_3—General PM Configuration 3 Register (PM—D31:F0) ......................................................................... 492 13.8.1.4 GEN_PMCON_LOCK- General Power Management Configuration Lock Register ...................................................... 494 13.8.1.5 C5_EXIT_TIMING_CNT- C5 Exit Timing Register (Mobile Only)....... 495 13.8.1.6 Cx-STATE_CNF—Cx State Configuration Register (PM—D31:F0) (Mobile Only, Except Bit 2)................................... 496 13.8.1.7 C4-TIMING_CNT—C4 Timing Control Register (PM—D31:F0) (Mobile Only) ..................................................... 497 13.8.1.8 BM_BREAK_EN Register (PM—D31:F0) (Mobile Only) ................... 498 13.8.1.9 PMIR—Power Management Initialization Register (PM—D31:F0)..... 499 13.8.1.10GPIO_ROUT—GPIO Routing Control Register (PM—D31:F0) ......................................................................... 499 13.8.2 APM I/O Decode ................................................................................... 500 13.8.2.1 APM_CNT—Advanced Power Management Control Port Register ..... 500 13.8.2.2 APM_STS—Advanced Power Management Status Port Register ...... 500 13.8.3 Power Management I/O Registers ........................................................... 501 13.8.3.1 PM1_STS—Power Management 1 Status Register......................... 503 13.8.3.2 PM1_EN—Power Management 1 Enable Register .......................... 506 13.8.3.3 PM1_CNT—Power Management 1 Control.................................... 507 13.8.3.4 PM1_TMR—Power Management 1 Timer Register ......................... 508 13.8.3.5 PROC_CNT—Processor Control Register ...................................... 508 13.8.3.6 LV2 — Level 2 Register ............................................................ 510 13.8.3.7 LV3—Level 3 Register (Mobile Only)........................................... 510 13.8.3.8 LV4—Level 4 Register (Mobile Only)........................................... 510 13.8.3.9 LV5—Level 5 Register (Mobile Only)........................................... 511 13.8.3.10LV6—Level 6 Register (Mobile Only)........................................... 511 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 13.8.3.11GPE0_STS—General Purpose Event 0 Status Register .................. 512 13.8.3.12GPE0_EN—General Purpose Event 0 Enables Register .................. 515 13.8.3.13SMI_EN—SMI Control and Enable Register ................................. 517 13.8.3.14SMI_STS—SMI Status Register ................................................. 519 13.8.3.15ALT_GP_SMI_EN—Alternate GPI SMI Enable Register .................. 521 13.8.3.16ALT_GP_SMI_STS—Alternate GPI SMI Status Register ................. 522 13.8.3.17UPRWC—USB Per-Port Registers Write Control ............................ 522 13.8.3.18GPE_CNTL— General Purpose Control Register............................ 523 13.8.3.19DEVACT_STS — Device Activity Status Register .......................... 523 13.8.3.20PM2_CNT—Power Management 2 Control (Mobile Only)................ 524 13.8.3.21C3_RES— C3 Residency Register (Mobile Only) ........................... 524 13.8.3.22C5_RES— C5 Residency Register (Mobile Only) ........................... 525 13.9 System Management TCO Registers (D31:F0) ..................................................... 526 13.9.1 TCO_RLD—TCO Timer Reload and Current Value Register .......................... 526 13.9.2 TCO_DAT_IN—TCO Data In Register ....................................................... 527 13.9.3 TCO_DAT_OUT—TCO Data Out Register .................................................. 527 13.9.4 TCO1_STS—TCO1 Status Register .......................................................... 527 13.9.5 TCO2_STS—TCO2 Status Register .......................................................... 529 13.9.6 TCO1_CNT—TCO1 Control Register ......................................................... 531 13.9.7 TCO2_CNT—TCO2 Control Register ......................................................... 532 13.9.8 TCO_MESSAGE1 and TCO_MESSAGE2 Registers ....................................... 532 13.9.9 TCO_WDCNT—TCO Watchdog Control Register ......................................... 533 13.9.10SW_IRQ_GEN—Software IRQ Generation Register .................................... 533 13.9.11TCO_TMR—TCO Timer Initial Value Register............................................. 533 13.10 General Purpose I/O Registers (D31:F0)............................................................. 534 13.10.1GPIO_USE_SEL—GPIO Use Select Register [31:0] .................................... 535 13.10.2GP_IO_SEL—GPIO Input/Output Select Register [31:0] ............................. 535 13.10.3GP_LVL—GPIO Level for Input or Output Register [31:0] ........................... 536 13.10.4GPO_BLINK—GPO Blink Enable Register [31:0] ........................................ 536 13.10.5GP_SER_BLINK[31:0]—GP Serial Blink [31:0] .......................................... 537 13.10.6GP_SB_CMDSTS[31:0]—GP Serial Blink Command Status [31:0]................ 538 13.10.7GP_SB_DATA[31:0]—GP Serial Blink Data [31:0] ..................................... 538 13.10.8GPI_INV—GPIO Signal Invert Register [31:0]........................................... 539 13.10.9GPIO_USE_SEL2—GPIO Use Select 2 Register [60:32] .............................. 539 13.10.10GP_IO_SEL2—GPIO Input/Output Select 2 Register [60:32] ..................... 540 13.10.11GP_LVL2—GPIO Level for Input or Output 2 Register [63:32] ................... 540 14 SATA Controller Registers (D31:F2)....................................................................... 541 14.1 PCI Configuration Registers (SATA–D31:F2)........................................................ 541 14.1.1 VID—Vendor Identification Register (SATA—D31:F2) ................................ 542 14.1.2 DID—Device Identification Register (SATA—D31:F2) ................................. 543 14.1.3 PCICMD—PCI Command Register (SATA–D31:F2)..................................... 543 14.1.4 PCISTS — PCI Status Register (SATA–D31:F2) ......................................... 544 14.1.5 RID—Revision Identification Register (SATA—D31:F2)............................... 545 14.1.6 PI—Programming Interface Register (SATA–D31:F2)................................. 545 14.1.6.1 When Sub Class Code Register (D31:F2:Offset 0Ah) = 01h .......... 545 14.1.6.2 When Sub Class Code Register (D31:F2:Offset 0Ah) = 04h .......... 546 14.1.6.3 When Sub Class Code Register (D31:F2:Offset 0Ah) = 06h .......... 546 14.1.7 SCC—Sub Class Code Register (SATA–D31:F2) ........................................ 546 14.1.8 BCC—Base Class Code Register (SATA–D31:F2SATA–D31:F2) .................... 547 14.1.9 PMLT—Primary Master Latency Timer Register (SATA–D31:F2) ................... 547 14.1.10HTYPE—Header Type (SATA–D31:F2) ..................................................... 547 14.1.11PCMD_BAR—Primary Command Block Base Address Register (SATA–D31:F2) ....................................................................... 547 14.1.12PCNL_BAR—Primary Control Block Base Address Register (SATA–D31:F2).................................................................................... 548 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 17 14.2 14.3 14.4 18 14.1.13SCMD_BAR—Secondary Command Block Base Address Register (IDE D31:F1) ........................................................................... 548 14.1.14SCNL_BAR—Secondary Control Block Base Address Register (IDE D31:F1) ........................................................................... 548 14.1.15BAR — Legacy Bus Master Base Address Register (SATA–D31:F2) .................................................................................... 549 14.1.16ABAR/SIDPBA1 — AHCI Base Address Register/Serial ATA Index Data Pair Base Address (SATA–D31:F2) ................................................... 549 14.1.16.1When SCC is not 01h ............................................................... 549 14.1.16.2When SCC is 01h .................................................................... 550 14.1.17SVID—Subsystem Vendor Identification Register (SATA–D31:F2) ................ 550 14.1.18SID—Subsystem Identification Register (SATA–D31:F2)............................. 550 14.1.19CAP—Capabilities Pointer Register (SATA–D31:F2) .................................... 550 14.1.20INT_LN—Interrupt Line Register (SATA–D31:F2)....................................... 551 14.1.21INT_PN—Interrupt Pin Register (SATA–D31:F2) ........................................ 551 14.1.22IDE_TIM — IDE Timing Register (SATA–D31:F2) ....................................... 551 14.1.23PID—PCI Power Management Capability Identification Register (SATA–D31:F2)........................................................................ 551 14.1.24PC—PCI Power Management Capabilities Register (SATA–D31:F2) .................................................................................... 552 14.1.25PMCS—PCI Power Management Control and Status Register (SATA–D31:F2)........................................................................ 552 14.1.26MSICI—Message Signaled Interrupt Capability Identification (SATA–D31:F2) 553 14.1.27MSIMC—Message Signaled Interrupt Message Control (SATA–D31:F2) ......... 554 14.1.28MSIMA— Message Signaled Interrupt Message Address (SATA–D31:F2) ....... 555 14.1.29MSIMD—Message Signaled Interrupt Message Data (SATA–D31:F2) ............ 555 14.1.30MAP—Address Map Register (SATA–D31:F2)............................................. 556 14.1.31PCS—Port Control and Status Register (SATA–D31:F2) .............................. 556 14.1.32SCLKCG - SATA Clock Gating Control Register .......................................... 559 14.1.33SCLKGC - SATA Clock General Configuration Register ................................ 560 14.1.33.1SATACR0—SATA Capability Register 0 (SATA–D31:F2) ................. 561 14.1.33.2SATACR1—SATA Capability Register 1 (SATA–D31:F2) ................. 561 14.1.34FLRCID—FLR Capability ID (SATA–D31:F2) .............................................. 562 14.1.35FLRCLV—FLR Capability Length and Version (SATA–D31:F2)....................... 562 14.1.36FLRC—FLR Control (SATA–D31:F2) ......................................................... 563 14.1.37ATC—APM Trapping Control Register (SATA–D31:F2)................................. 563 14.1.38ATS—APM Trapping Status Register (SATA–D31:F2).................................. 564 14.1.39SP Scratch Pad Register (SATA–D31:F2) .................................................. 564 14.1.40BFCS—BIST FIS Control/Status Register (SATA–D31:F2) ........................... 565 14.1.41BFTD1—BIST FIS Transmit Data1 Register (SATA–D31:F2) ........................ 567 14.1.42BFTD2—BIST FIS Transmit Data2 Register (SATA–D31:F2) ........................ 567 Bus Master IDE I/O Registers (D31:F2)............................................................... 568 14.2.1 BMIC[P,S]—Bus Master IDE Command Register (D31:F2) .......................... 569 14.2.2 BMIS[P,S]—Bus Master IDE Status Register (D31:F2)................................ 570 14.2.3 BMID[P,S]—Bus Master IDE Descriptor Table Pointer Register (D31:F2)................................................................................. 571 14.2.4 AIR—AHCI Index Register (D31:F2) ........................................................ 571 14.2.5 AIDR—AHCI Index Data Register (D31:F2)............................................... 571 Serial ATA Index/Data Pair Superset Registers..................................................... 572 14.3.1 SINDX – Serial ATA Index (D31:F2) ........................................................ 572 14.3.2 SDATA – Serial ATA Data (D31:F2) ......................................................... 573 14.3.2.1 PxSSTS—Serial ATA Status Register (D31:F2) ............................. 574 14.3.2.2 PxSCTL — Serial ATA Control Register (D31:F2) .......................... 575 14.3.2.3 PxSERR—Serial ATA Error Register (D31:F2)............................... 576 AHCI Registers (D31:F2) .................................................................................. 577 14.4.1 AHCI Generic Host Control Registers (D31:F2).......................................... 578 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 14.4.1.1 14.4.1.2 14.4.1.3 14.4.1.4 14.4.1.5 14.4.1.6 CAP—Host Capabilities Register (D31:F2)................................... 578 GHC—Global ICH9 Control Register (D31:F2).............................. 580 IS—Interrupt Status Register (D31:F2) ...................................... 581 PI—Ports Implemented Register (D31:F2) .................................. 582 VS—AHCI Version (D31:F2) ..................................................... 583 CCC_CTL—Command Completion Coalescing Control Register (D31:F2) ................................................................... 583 14.4.1.7 CCC_Ports—Command Completion Coalescing Ports Register (D31:F2) ................................................................... 584 14.4.1.8 EM_LOC—Enclosure Management Location Register (D31:F2) ....... 584 14.4.1.9 EM_CTRL—Enclosure Management Control Register (D31:F2) ....... 585 14.4.2 Vendor Specific Registers (D31:F2)......................................................... 586 14.4.2.1 VSP—Vendor Specific (D31:F2)................................................. 586 14.4.3 Port Registers (D31:F2) ........................................................................ 586 14.4.3.1 PxCLB—Port [5:0] Command List Base Address Register (D31:F2) ............................................................................... 589 14.4.3.2 PxCLBU—Port [5:0] Command List Base Address Upper 32-Bits Register (D31:F2) ........................................................ 589 14.4.3.3 PxFB—Port [5:0] FIS Base Address Register (D31:F2).................. 590 14.4.3.4 PxFBU—Port [5:0] FIS Base Address Upper 32-Bits Register (D31:F2) ................................................................... 590 14.4.3.5 PxIS—Port [5:0] Interrupt Status Register (D31:F2).................... 591 14.4.3.6 PxIE—Port [5:0] Interrupt Enable Register (D31:F2).................... 592 14.4.3.7 PxCMD—Port [5:0] Command Register (D31:F2)......................... 594 14.4.3.8 PxTFD—Port [5:0] Task File Data Register (D31:F2) .................... 597 14.4.3.9 PxSIG—Port [5:0] Signature Register (D31:F2)........................... 598 14.4.3.10PxSSTS—Port [5:0] Serial ATA Status Register (D31:F2).............. 599 14.4.3.11PxSCTL — Port [5:0] Serial ATA Control Register (D31:F2) ........... 600 14.4.3.12PxSERR—Port [5:0] Serial ATA Error Register (D31:F2)................ 601 14.4.3.13PxSACT—Port [5:0] Serial ATA Active (D31:F2) .......................... 603 14.4.3.14PxCI—Port [5:0] Command Issue Register (D31:F2).................... 603 15 SATA Controller Registers (D31:F5)....................................................................... 605 15.1 PCI Configuration Registers (SATA–D31:F5)........................................................ 605 15.1.1 VID—Vendor Identification Register (SATA—D31:F5) ................................ 606 15.1.2 DID—Device Identification Register (SATA—D31:F5) ................................. 607 15.1.3 PCICMD—PCI Command Register (SATA–D31:F5)..................................... 607 15.1.4 PCISTS — PCI Status Register (SATA–D31:F5) ......................................... 608 15.1.5 RID—Revision Identification Register (SATA—D31:F5)............................... 608 15.1.6 PI—Programming Interface Register (SATA–D31:F5)................................. 609 15.1.7 SCC—Sub Class Code Register (SATA–D31:F5) ........................................ 609 15.1.8 BCC—Base Class Code Register (SATA–D31:F5) ....................................... 609 15.1.9 PMLT—Primary Master Latency Timer Register (SATA–D31:F5) ................... 610 15.1.10PCMD_BAR—Primary Command Block Base Address Register (SATA–D31:F5) ....................................................................... 610 15.1.11PCNL_BAR—Primary Control Block Base Address Register (SATA–D31:F5).................................................................................... 610 15.1.12SCMD_BAR—Secondary Command Block Base Address Register (IDE D31:F1) .......................................................................... 611 15.1.13SCNL_BAR—Secondary Control Block Base Address Register (IDE D31:F1) .......................................................................... 611 15.1.14BAR — Legacy Bus Master Base Address Register (SATA–D31:F5).................................................................................... 612 15.1.15SIDPBA — SATA Index/Data Pair Base Address Register (SATA–D31:F5).................................................................................... 612 15.1.16SVID—Subsystem Vendor Identification Register (SATA–D31:F5).................................................................................... 613 15.1.17SID—Subsystem Identification Register (SATA–D31:F5) ............................ 613 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 19 15.2 15.3 15.4 16 20 15.1.18CAP—Capabilities Pointer Register (SATA–D31:F5) .................................... 613 15.1.19INT_LN—Interrupt Line Register (SATA–D31:F5)....................................... 613 15.1.20INT_PN—Interrupt Pin Register (SATA–D31:F5) ........................................ 613 15.1.21IDE_TIM — IDE Timing Register (SATA–D31:F5) ....................................... 614 15.1.22PID—PCI Power Management Capability Identification Register (SATA–D31:F5)........................................................................ 614 15.1.23PC—PCI Power Management Capabilities Register (SATA–D31:F5) .................................................................................... 614 15.1.24PMCS—PCI Power Management Control and Status Register (SATA–D31:F5)........................................................................ 615 15.1.25MID—Message Signal Interrupt Identifier (SATA–D31:F5) .......................... 615 15.1.26MC—Message Signal Interrupt Message Control (SATA–D31:F5).................. 616 15.1.27MA—Message Signal Interrupt Message Address (SATA–D31:F5)................. 616 15.1.28MD—Message Signal Interrupt Message Data (SATA–D31:F5) ..................... 616 15.1.29MAP—Address Map Register (SATA–D31:F5)16 ......................................... 617 15.1.30PCS—Port Control and Status Register (SATA–D31:F5) .............................. 618 15.1.31SATACR0— SATA Capability Register 0 (SATA–D31:F5) ............................. 619 15.1.32SATACR1— SATA Capability Register 1 (SATA–D31:F5) ............................. 619 15.1.33FLRCID— FLR Capability ID (SATA–D31:F5) ............................................. 619 15.1.34FLRCLV— FLR Capability Length and Value (SATA–D31:F5) ........................ 620 15.1.35FLRCTRL— FLR Control (SATA–D31:F5) ................................................... 620 15.1.36ATC—APM Trapping Control Register (SATA–D31:F5)................................. 621 15.1.37ATC—APM Trapping Control (SATA–D31:F5) ............................................. 621 Bus Master IDE I/O Registers (D31:F5)............................................................... 622 15.2.1 BMIC[P,S]—Bus Master IDE Command Register (D31:F5) .......................... 623 15.2.2 BMIS[P,S]—Bus Master IDE Status Register (D31:F5)................................ 624 15.2.3 BMID[P,S]—Bus Master IDE Descriptor Table Pointer Register (D31:F5)................................................................................. 624 AHCI Index Data Pair Registers.......................................................................... 625 15.3.1 INDEX—AHCI Index Register (D31:F5) .................................................... 625 15.3.2 Data—AHCI Data Register (D31:F5) ........................................................ 625 Serial ATA Index/Data Pair Superset Registers..................................................... 626 15.4.1 SINDX—SATA Index Register (D31:F5) .................................................... 626 15.4.2 SDATA—SATA Index Data Register (D31:F5) ............................................ 626 15.4.2.1 PxSSTS—Serial ATA Status Register (D31:F5) ............................. 627 15.4.2.2 PxSCTL — Serial ATA Control Register (D31:F5) .......................... 628 15.4.2.3 PxSERR—Serial ATA Error Register (D31:F5)............................... 629 UHCI Controllers Registers .................................................................................... 631 16.1 PCI Configuration Registers (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2)............................................................. 631 16.1.1 VID—Vendor Identification Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 632 16.1.2 DID—Device Identification Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 632 16.1.3 PCICMD—PCI Command Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2)... 633 16.1.4 PCISTS—PCI Status Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 634 16.1.5 RID—Revision Identification Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 634 16.1.6 PI—Programming Interface Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 635 16.1.7 SCC—Sub Class Code Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 635 16.1.8 BCC—Base Class Code Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2).................................................. 635 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 16.2 17 16.1.9 MLT—Master Latency Timer Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 635 16.1.10HEADTYP—Header Type Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 636 16.1.11BASE—Base Address Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 636 16.1.12SVID — Subsystem Vendor Identification Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 636 16.1.13SID — Subsystem Identification Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 637 16.1.14CAP_PTR—Capabilities Pointer (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 637 16.1.15INT_LN—Interrupt Line Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 637 16.1.16INT_PN—Interrupt Pin Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 638 16.1.17FLRCID—Function Level Reset Capability ID (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 638 16.1.18FLRNCP—Function Level Reset Next Capability Pointer (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 638 16.1.19FLRCLV—Function Level Reset Capability Length and Version (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 639 16.1.20USB_FLRCTRL—FLR Control Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 639 16.1.21USB_FLRSTAT—FLR Status Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 640 16.1.22USB_RELNUM—Serial Bus Release Number Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 640 16.1.23USB_LEGKEY—USB Legacy Keyboard/Mouse Control Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2)..................................... 640 16.1.24USB_RES—USB Resume Enable Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 642 16.1.25CWP—Core Well Policy Register (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 643 16.1.26UCR1—UCHI Configuration Register 1 (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................. 643 USB I/O Registers ........................................................................................... 644 16.2.1 USBCMD—USB Command Register ......................................................... 645 16.2.2 USBSTS—USB Status Register ............................................................... 648 16.2.3 USBINTR—USB Interrupt Enable Register ................................................ 649 16.2.4 FRNUM—Frame Number Register............................................................ 649 16.2.5 FRBASEADD—Frame List Base Address Register ....................................... 650 16.2.6 SOFMOD—Start of Frame Modify Register ................................................ 651 16.2.7 PORTSC[0,1]—Port Status and Control Register........................................ 652 EHCI Controller Registers (D29:F7, D26:F7) .......................................................... 655 17.1 USB EHCI Configuration Registers (USB EHCI—D29:F7, D26:F7) ........................... 655 17.1.1 VID—Vendor Identification Register (USB EHCI—D29:F7, D26:F7) ................................................................ 656 17.1.2 DID—Device Identification Register (USB EHCI—D29:F7, D26:F7) ................................................................ 656 17.1.3 PCICMD—PCI Command Register (USB EHCI—D29:F7, D26:F7) ................................................................ 657 17.1.4 PCISTS—PCI Status Register (USB EHCI—D29:F7, D26:F7) ....................... 658 17.1.5 RID—Revision Identification Register (USB EHCI—D29:F7, D26:F7) ................................................................ 659 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 21 17.1.6 PI—Programming Interface Register (USB EHCI—D29:F7, D26:F7)................................................................. 659 17.1.7 SCC—Sub Class Code Register (USB EHCI—D29:F7, D26:F7)................................................................. 659 17.1.8 BCC—Base Class Code Register (USB EHCI—D29:F7, D26:F7)................................................................. 659 17.1.9 PMLT—Primary Master Latency Timer Register (USB EHCI—D29:F7, D26:F7)................................................................. 660 17.1.10MEM_BASE—Memory Base Address Register (USB EHCI—D29:F7, D26:F7)................................................................. 660 17.1.11SVID—USB EHCI Subsystem Vendor ID Register (USB EHCI—D29:F7, D26:F7)................................................................. 660 17.1.12SID—USB EHCI Subsystem ID Register (USB EHCI—D29:F7, D26:F7)................................................................. 661 17.1.13CAP_PTR—Capabilities Pointer Register (USB EHCI—D29:F7, D26:F7)................................................................. 661 17.1.14INT_LN—Interrupt Line Register (USB EHCI—D29:F7, D26:F7)................................................................. 661 17.1.15INT_PN—Interrupt Pin Register (USB EHCI—D29:F7, D26:F7)................................................................. 661 17.1.16PWR_CAPID—PCI Power Management Capability ID Register (USB EHCI—D29:F7, D26:F7) .................................................... 662 17.1.17NXT_PTR1—Next Item Pointer #1 Register (USB EHCI—D29:F7, D26:F7)................................................................. 662 17.1.18PWR_CAP—Power Management Capabilities Register (USB EHCI—D29:F7, D26:F7)................................................................. 663 17.1.19PWR_CNTL_STS—Power Management Control/ Status Register (USB EHCI—D29:F7, D26:F7) .......................................... 664 17.1.20DEBUG_CAPID—Debug Port Capability ID Register (USB EHCI—D29:F7, D26:F7)................................................................. 665 17.1.21NXT_PTR2—Next Item Pointer #2 Register (USB EHCI—D29:F7, D26:F7)................................................................. 665 17.1.22DEBUG_BASE—Debug Port Base Offset Register (USB EHCI—D29:F7, D26:F7)................................................................. 665 17.1.23USB_RELNUM—USB Release Number Register (USB EHCI—D29:F7, D26:F7)................................................................. 665 17.1.24FL_ADJ—Frame Length Adjustment Register (USB EHCI—D29:F7, D26:F7)................................................................. 666 17.1.25PWAKE_CAP—Port Wake Capability Register (USB EHCI—D29:F7, D26:F7)................................................................. 667 17.1.26LEG_EXT_CAP—USB EHCI Legacy Support Extended Capability Register (USB EHCI—D29:F7, D26:F7)...................................... 668 17.1.27LEG_EXT_CS—USB EHCI Legacy Support Extended Control / Status Register (USB EHCI—D29:F7, D26:F7) ............................. 668 17.1.28SPECIAL_SMI—Intel Specific USB 2.0 SMI Register (USB EHCI—D29:F7, D26:F7)................................................................. 671 17.1.29ACCESS_CNTL—Access Control Register (USB EHCI—D29:F7, D26:F7)................................................................. 673 17.1.30EHCIIR1—EHCI Initialization Register 1 (USB EHCI—D29:F7, D26:F7)................................................................. 673 17.1.31FLR_CID—Function Level Reset Capability ID (USB EHCI—D29:F7, D26:F7)................................................................. 673 17.1.32FLR_NEXT—Function Level Reset Next Capability Pointer (USB EHCI—D29:F7, D26:F7)................................................................. 674 17.1.33FLR_CLV—Function Level Reset Capability Length and Version (USB EHCI—D29:F7, D26:F7)................................................................. 674 22 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 17.2 18 17.1.34FLR_CTRL—Function Level Reset Control Register (USB EHCI—D29:F7, D26:F7) ................................................................ 675 17.1.35FLR_STS—Function Level Reset Status Register (USB EHCI—D29:F7, D26:F7) ................................................................ 675 17.1.36EHCIIR2—EHCI Initialization Register 2 (USB EHCI—D29:F7, D26:F7) ................................................................ 675 Memory-Mapped I/O Registers .......................................................................... 676 17.2.1 Host Controller Capability Registers ........................................................ 676 17.2.1.1 CAPLENGTH—Capability Registers Length Register ...................... 677 17.2.1.2 HCIVERSION—Host Controller Interface Version Number Register................................................................................. 677 17.2.1.3 HCSPARAMS—Host Controller Structural Parameters.................... 678 17.2.1.4 HCCPARAMS—Host Controller Capability Parameters Register................................................................................. 679 17.2.2 Host Controller Operational Registers ...................................................... 680 17.2.2.1 USB2.0_CMD—USB 2.0 Command Register ................................ 681 17.2.2.2 USB2.0_STS—USB 2.0 Status Register ...................................... 684 17.2.2.3 USB2.0_INTR—USB 2.0 Interrupt Enable Register ....................... 686 17.2.2.4 FRINDEX—Frame Index Register ............................................... 687 17.2.2.5 CTRLDSSEGMENT—Control Data Structure Segment Register................................................................................. 688 17.2.2.6 PERIODICLISTBASE—Periodic Frame List Base Address Register................................................................................. 688 17.2.2.7 ASYNCLISTADDR—Current Asynchronous List Address Register................................................................................. 689 17.2.2.8 CONFIGFLAG—Configure Flag Register....................................... 689 17.2.2.9 PORTSC—Port N Status and Control Register .............................. 690 17.2.3 USB 2.0-Based Debug Port Register........................................................ 694 17.2.3.1 CNTL_STS—Control/Status Register .......................................... 695 17.2.3.2 USBPID—USB PIDs Register ..................................................... 697 17.2.3.3 DATABUF[7:0]—Data Buffer Bytes[7:0] Register ......................... 697 17.2.3.4 CONFIG—Configuration Register ............................................... 697 Intel® High Definition Audio Controller Registers (D27:F0) ................................... 699 18.1 Intel® High Definition Audio PCI Configuration Space (Intel® High Definition Audio— D27:F0) ............................................................. 699 18.1.1 VID—Vendor Identification Register (Intel® High Definition Audio Controller—D27:F0)..................................... 701 18.1.2 DID—Device Identification Register (Intel® High Definition Audio Controller—D27:F0)..................................... 701 18.1.3 PCICMD—PCI Command Register (Intel® High Definition Audio Controller—D27:F0)..................................... 701 18.1.4 PCISTS—PCI Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 702 18.1.5 RID—Revision Identification Register (Intel® High Definition Audio Controller—D27:F0)..................................... 703 18.1.6 PI—Programming Interface Register (Intel® High Definition Audio Controller—D27:F0)..................................... 703 18.1.7 SCC—Sub Class Code Register (Intel® High Definition Audio Controller—D27:F0)..................................... 703 18.1.8 BCC—Base Class Code Register (Intel® High Definition Audio Controller—D27:F0)..................................... 703 18.1.9 CLS—Cache Line Size Register (Intel® High Definition Audio Controller—D27:F0)..................................... 703 18.1.10LT—Latency Timer Register (Intel® High Definition Audio Controller—D27:F0)..................................... 704 18.1.11HEADTYP—Header Type Register (Intel® High Definition Audio Controller—D27:F0)..................................... 704 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 23 18.1.12HDBARL—Intel® High Definition Audio Lower Base Address Register (Intel® High Definition Audio—D27:F0).................................................... 704 18.1.13HDBARU—Intel® High Definition Audio Upper Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 704 18.1.14SVID—Subsystem Vendor Identification Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 705 18.1.15SID—Subsystem Identification Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 705 18.1.16CAPPTR—Capabilities Pointer Register (Audio—D27:F0) ............................. 705 18.1.17INTLN—Interrupt Line Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 706 18.1.18INTPN—Interrupt Pin Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 706 18.1.19HDCTL—Intel® High Definition Audio Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 706 18.1.20TCSEL—Traffic Class Select Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 707 18.1.21DCKCTL—Docking Control Register (Mobile Only) (Intel® High Definition Audio Controller—D27:F0) ..................................... 707 18.1.22DCKSTS—Docking Status Register (Mobile Only) (Intel® High Definition Audio Controller—D27:F0) ..................................... 708 18.1.23PID—PCI Power Management Capability ID Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 708 18.1.24PC—Power Management Capabilities Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 709 18.1.25PCS—Power Management Control and Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 710 18.1.26MID—MSI Capability ID Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 711 18.1.27MMC—MSI Message Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 711 18.1.28MMLA—MSI Message Lower Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 711 18.1.29MMUA—MSI Message Upper Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 711 18.1.30MMD—MSI Message Data Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 712 18.1.31PXID—PCI Express* Capability ID Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 712 18.1.32PXC—PCI Express* Capabilities Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 712 18.1.33DEVCAP—Device Capabilities Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 713 18.1.34DEVC—Device Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 714 18.1.35DEVS—Device Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 715 18.1.36VCCAP—Virtual Channel Enhanced Capability Header (Intel® High Definition Audio Controller—D27:F0) ..................................... 715 18.1.37PVCCAP1—Port VC Capability Register 1 (Intel® High Definition Audio Controller—D27:F0) ..................................... 716 18.1.38PVCCAP2 — Port VC Capability Register 2 (Intel® High Definition Audio Controller—D27:F0) ..................................... 716 18.1.39PVCCTL — Port VC Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 716 18.1.40PVCSTS—Port VC Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 717 24 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 18.2 18.1.41VC0CAP—VC0 Resource Capability Register (Intel® High Definition Audio Controller—D27:F0)..................................... 717 18.1.42VC0CTL—VC0 Resource Control Register (Intel® High Definition Audio Controller—D27:F0)..................................... 718 18.1.43VC0STS—VC0 Resource Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 718 18.1.44VCiCAP—VCi Resource Capability Register (Intel® High Definition Audio Controller—D27:F0)..................................... 719 18.1.45VCiCTL—VCi Resource Control Register (Intel® High Definition Audio Controller—D27:F0)..................................... 719 18.1.46VCiSTS—VCi Resource Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 720 18.1.47RCCAP—Root Complex Link Declaration Enhanced Capability Header Register (Intel® High Definition Audio Controller—D27:F0)720 18.1.48ESD—Element Self Description Register (Intel® High Definition Audio Controller—D27:F0)..................................... 720 18.1.49L1DESC—Link 1 Description Register (Intel® High Definition Audio Controller—D27:F0)..................................... 721 18.1.50L1ADDL—Link 1 Lower Address Register (Intel® High Definition Audio Controller—D27:F0)..................................... 721 18.1.51L1ADDU—Link 1 Upper Address Register (Intel® High Definition Audio Controller—D27:F0)..................................... 721 Intel® High Definition Audio Memory Mapped Configuration Registers (Intel® High Definition Audio— D27:F0) ............................................................. 722 18.2.1 GCAP—Global Capabilities Register (Intel® High Definition Audio Controller—D27:F0)..................................... 726 18.2.2 VMIN—Minor Version Register (Intel® High Definition Audio Controller—D27:F0)..................................... 726 18.2.3 VMAJ—Major Version Register (Intel® High Definition Audio Controller—D27:F0)..................................... 726 18.2.4 OUTPAY—Output Payload Capability Register (Intel® High Definition Audio Controller—D27:F0)..................................... 727 18.2.5 INPAY—Input Payload Capability Register (Intel® High Definition Audio Controller—D27:F0)..................................... 727 18.2.6 GCTL—Global Control Register (Intel® High Definition Audio Controller—D27:F0)..................................... 728 18.2.7 WAKEEN—Wake Enable Register (Intel® High Definition Audio Controller—D27:F0)..................................... 729 18.2.8 STATESTS—State Change Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 729 18.2.9 GSTS—Global Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 730 18.2.10ECAP—Extended Capabilities (Mobile Only) (Intel® High Definition Audio Controller—D27:F0)..................................... 731 18.2.11OUTSTRMPAY—Output Stream Payload Capability (Intel® High Definition Audio Controller—D27:F0)..................................... 731 18.2.12INSTRMPAY—Input Stream Payload Capability (Intel® High Definition Audio Controller—D27:F0)..................................... 732 18.2.13INTCTL—Interrupt Control Register (Intel® High Definition Audio Controller—D27:F0)..................................... 733 18.2.14INTSTS—Interrupt Status Register (Intel® High Definition Audio Controller—D27:F0)..................................... 734 18.2.15WALCLK—Wall Clock Counter Register (Intel® High Definition Audio Controller—D27:F0)..................................... 734 18.2.16SSYNC—Stream Synchronization Register (Intel® High Definition Audio Controller—D27:F0)..................................... 735 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 25 18.2.17CORBLBASE—CORB Lower Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 735 18.2.18CORBUBASE—CORB Upper Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 736 18.2.19CORBWP—CORB Write Pointer Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 736 18.2.20CORBRP—CORB Read Pointer Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 736 18.2.21CORBCTL—CORB Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 737 18.2.22CORBST—CORB Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 737 18.2.23CORBSIZE—CORB Size Register Intel® High Definition Audio Controller—D27:F0) ...................................... 737 18.2.24RIRBLBASE—RIRB Lower Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 738 18.2.25RIRBUBASE—RIRB Upper Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 738 18.2.26RIRBWP—RIRB Write Pointer Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 738 18.2.27RINTCNT—Response Interrupt Count Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 739 18.2.28RIRBCTL—RIRB Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 739 18.2.29RIRBSTS—RIRB Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 740 18.2.30RIRBSIZE—RIRB Size Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 740 18.2.31IC—Immediate Command Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 740 18.2.32IR—Immediate Response Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 741 18.2.33IRS—Immediate Command Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 741 18.2.34DPLBASE—DMA Position Lower Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 742 18.2.35DPUBASE—DMA Position Upper Base Address Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 742 18.2.36SDCTL—Stream Descriptor Control Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 743 18.2.37SDSTS—Stream Descriptor Status Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 745 18.2.38SDLPIB—Stream Descriptor Link Position in Buffer Register (Intel® High Definition Audio Controller—D27:F0) ......................... 746 18.2.39SDCBL—Stream Descriptor Cyclic Buffer Length Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 746 18.2.40SDLVI—Stream Descriptor Last Valid Index Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 747 18.2.41SDFIFOW—Stream Descriptor FIFO Watermark Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 747 18.2.42SDFIFOS—Stream Descriptor FIFO Size Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 748 18.2.43SDFMT—Stream Descriptor Format Register (Intel® High Definition Audio Controller—D27:F0) ..................................... 749 18.2.44SDBDPL—Stream Descriptor Buffer Descriptor List Pointer Lower Base Address Register (Intel® High Definition Audio Controller—D27:F0) ............. 750 26 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 18.2.45SDBDPU—Stream Descriptor Buffer Descriptor List Pointer Upper Base Address Register (Intel® High Definition Audio Controller—D27:F0) ............ 750 19 SMBus Controller Registers (D31:F3) .................................................................... 751 19.1 PCI Configuration Registers (SMBus—D31:F3)..................................................... 751 19.1.1 VID—Vendor Identification Register (SMBus—D31:F3)............................... 751 19.1.2 DID—Device Identification Register (SMBus—D31:F3) ............................... 752 19.1.3 PCICMD—PCI Command Register (SMBus—D31:F3) .................................. 752 19.1.4 PCISTS—PCI Status Register (SMBus—D31:F3) ........................................ 753 19.1.5 RID—Revision Identification Register (SMBus—D31:F3) ............................. 753 19.1.6 PI—Programming Interface Register (SMBus—D31:F3) .............................. 754 19.1.7 SCC—Sub Class Code Register (SMBus—D31:F3)...................................... 754 19.1.8 BCC—Base Class Code Register (SMBus—D31:F3) .................................... 754 19.1.9 SMBMBAR0—D31_F3_SMBus Memory Base Address 0 (SMBus—D31:F3) ..... 754 19.1.10SMBMBAR1—D31_F3_SMBus Memory Base Address 1 (SMBus—D31:F3) ..... 755 19.1.11SMB_BASE—SMBus Base Address Register (SMBus—D31:F3)..................... 755 19.1.12SVID—Subsystem Vendor Identification Register (SMBus—D31:F2/F4) ........ 755 19.1.13SID—Subsystem Identification Register (SMBus—D31:F2/F4)..................... 756 19.1.14INT_LN—Interrupt Line Register (SMBus—D31:F3) ................................... 756 19.1.15INT_PN—Interrupt Pin Register (SMBus—D31:F3)..................................... 756 19.1.16HOSTC—Host Configuration Register (SMBus—D31:F3) ............................. 757 19.2 SMBus I/O and Memory Mapped I/O Registers .................................................... 758 19.2.1 HST_STS—Host Status Register (SMBus—D31:F3).................................... 759 19.2.2 HST_CNT—Host Control Register (SMBus—D31:F3) .................................. 760 19.2.3 HST_CMD—Host Command Register (SMBus—D31:F3).............................. 762 19.2.4 XMIT_SLVA—Transmit Slave Address Register (SMBus—D31:F3) ................ 762 19.2.5 HST_D0—Host Data 0 Register (SMBus—D31:F3) ..................................... 762 19.2.6 HST_D1—Host Data 1 Register (SMBus—D31:F3) ..................................... 762 19.2.7 Host_BLOCK_DB—Host Block Data Byte Register (SMBus—D31:F3) ............ 763 19.2.8 PEC—Packet Error Check (PEC) Register (SMBus—D31:F3) ........................ 763 19.2.9 RCV_SLVA—Receive Slave Address Register (SMBus—D31:F3) ................... 764 19.2.10SLV_DATA—Receive Slave Data Register (SMBus—D31:F3) ....................... 764 19.2.11AUX_STS—Auxiliary Status Register (SMBus—D31:F3) .............................. 764 19.2.12AUX_CTL—Auxiliary Control Register (SMBus—D31:F3) ............................. 765 19.2.13SMLINK_PIN_CTL—SMLink Pin Control Register (SMBus—D31:F3) .............. 765 19.2.14SMBus_PIN_CTL—SMBus Pin Control Register (SMBus—D31:F3)................. 766 19.2.15SLV_STS—Slave Status Register (SMBus—D31:F3)................................... 766 19.2.16SLV_CMD—Slave Command Register (SMBus—D31:F3)............................. 767 19.2.17NOTIFY_DADDR—Notify Device Address Register (SMBus—D31:F3) ............ 767 19.2.18NOTIFY_DLOW—Notify Data Low Byte Register (SMBus—D31:F3) ............... 768 19.2.19NOTIFY_DHIGH—Notify Data High Byte Register (SMBus—D31:F3) ............. 768 20 PCI Express* Configuration Registers.................................................................... 769 20.1 PCI Express* Configuration Registers (PCI Express—D28:F0/F1/F2/F3/F4/F5) ......... 769 20.1.1 VID—Vendor Identification Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 772 20.1.2 DID—Device Identification Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 772 20.1.3 PCICMD—PCI Command Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 773 20.1.4 PCISTS—PCI Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 774 20.1.5 RID—Revision Identification Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 775 20.1.6 PI—Programming Interface Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 775 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 27 20.1.7 SCC—Sub Class Code Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 775 20.1.8 BCC—Base Class Code Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 775 20.1.9 CLS—Cache Line Size Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 776 20.1.10PLT—Primary Latency Timer Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 776 20.1.11HEADTYP—Header Type Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 776 20.1.12BNUM—Bus Number Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 776 20.1.13SLT—Secondary Latency Timer (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 777 20.1.14IOBL—I/O Base and Limit Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 777 20.1.15SSTS—Secondary Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 778 20.1.16MBL—Memory Base and Limit Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 779 20.1.17PMBL—Prefetchable Memory Base and Limit Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 779 20.1.18PMBU32—Prefetchable Memory Base Upper 32 Bits Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)....................................... 779 20.1.19PMLU32—Prefetchable Memory Limit Upper 32 Bits Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)....................................... 780 20.1.20CAPP—Capabilities List Pointer Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 780 20.1.21INTR—Interrupt Information Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 780 20.1.22BCTRL—Bridge Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 781 20.1.23CLIST—Capabilities List Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 782 20.1.24XCAP—PCI Express* Capabilities Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 782 20.1.25DCAP—Device Capabilities Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 783 20.1.26DCTL—Device Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 784 20.1.27DSTS—Device Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 785 20.1.28LCAP—Link Capabilities Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 786 20.1.29LCTL—Link Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 788 20.1.30LSTS—Link Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 789 20.1.31SLCAP—Slot Capabilities Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 790 20.1.32SLCTL—Slot Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 791 20.1.33SLSTS—Slot Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 792 20.1.34RCTL—Root Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 793 28 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 20.1.35RSTS—Root Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 793 20.1.36MID—Message Signaled Interrupt Identifiers Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 794 20.1.37MC—Message Signaled Interrupt Message Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 794 20.1.38MA—Message Signaled Interrupt Message Address Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ...................................... 794 20.1.39MD—Message Signaled Interrupt Message Data Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 795 20.1.40SVCAP—Subsystem Vendor Capability Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 795 20.1.41SVID—Subsystem Vendor Identification Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 795 20.1.42PMCAP—Power Management Capability Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 795 20.1.43PMC—PCI Power Management Capabilities Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 796 20.1.44PMCS—PCI Power Management Control and Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ...................................... 797 20.1.45MPC2—Miscellaneous Port Configuration Register 2 (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 798 20.1.46MPC—Miscellaneous Port Configuration Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 798 20.1.47SMSCS—SMI/SCI Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 801 20.1.48RPDCGEN—Root Port Dynamic Clock Gating Enable (PCI Express-D28:F0/F1/F2/F3/F4/F5) .................................................... 802 20.1.49IPWS—Intel® PRO/Wireless 3945ABG Status (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 802 20.1.50PECR1—PCI Express* Configuration Register 1 (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 803 20.1.51VCH—Virtual Channel Capability Header Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 803 20.1.52VCAP2—Virtual Channel Capability 2 Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 803 20.1.53PVC—Port Virtual Channel Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 804 20.1.54PVS—Port Virtual Channel Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 804 20.1.55V0CAP—Virtual Channel 0 Resource Capability Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 804 20.1.56V0CTL—Virtual Channel 0 Resource Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 805 20.1.57V0STS—Virtual Channel 0 Resource Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 805 20.1.58UES—Uncorrectable Error Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 806 20.1.59UEM—Uncorrectable Error Mask (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 807 20.1.60UEV — Uncorrectable Error Severity (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 808 20.1.61CES — Correctable Error Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 809 20.1.62CEM — Correctable Error Mask Register (PCI Express—D28:F0/F1/F2/F3/F4/F5)................................................... 809 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 29 20.1.63AECC — Advanced Error Capabilities and Control Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 810 20.1.64RES — Root Error Status Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 810 20.1.65RCTCL — Root Complex Topology Capability List Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 810 20.1.66ESD—Element Self Description Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 811 20.1.67ULD — Upstream Link Description Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 811 20.1.68ULBA — Upstream Link Base Address Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 812 20.1.69PECR2 — PCI Express* Configuration Register 2 (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 812 20.1.70PEETM — PCI Express* Extended Test Mode Register (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 812 20.1.71PEC1 — PCI Express* Configuration Register 1 (PCI Express—D28:F0/F1/F2/F3/F4/F5) ................................................... 813 21 High Precision Event Timer Registers..................................................................... 815 21.1 Memory Mapped Registers ................................................................................ 815 21.1.1 GCAP_ID—General Capabilities and Identification Register ......................... 816 21.1.2 GEN_CONF—General Configuration Register ............................................. 817 21.1.3 GINTR_STA—General Interrupt Status Register......................................... 817 21.1.4 MAIN_CNT—Main Counter Value Register ................................................. 818 21.1.5 TIMn_CONF—Timer n Configuration and Capabilities Register ..................... 818 21.1.6 TIMn_COMP—Timer n Comparator Value Register ..................................... 820 22 Serial Peripheral Interface (SPI) ........................................................................... 821 22.1 Serial Peripheral Interface Memory Mapped Configuration Registers........................ 821 22.1.1 BFPR –BIOS Flash Primary Region Register (SPI Memory Mapped Configuration Registers).......................................... 822 22.1.2 HSFS—Hardware Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers).......................................... 823 22.1.3 HSFC—Hardware Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers).......................................... 824 22.1.4 FADDR—Flash Address Register (SPI Memory Mapped Configuration Registers).......................................... 825 22.1.5 FDATA0—Flash Data 0 Register (SPI Memory Mapped Configuration Registers).......................................... 825 22.1.6 FDATAN—Flash Data [N] Register (SPI Memory Mapped Configuration Registers).......................................... 826 22.1.7 FRAP—Flash Regions Access Permissions Register (SPI Memory Mapped Configuration Registers).......................................... 827 22.1.8 FREG0—Flash Region 0 (Flash Descriptor) Register (SPI Memory Mapped Configuration Registers).......................................... 828 22.1.9 FREG1—Flash Region 1 (BIOS Descriptor) Register (SPI Memory Mapped Configuration Registers).......................................... 828 22.1.10FREG2—Flash Region 2 (ME) Register (SPI Memory Mapped Configuration Registers).......................................... 829 22.1.11FREG3—Flash Region 3 (GbE) Register (SPI Memory Mapped Configuration Registers).......................................... 829 22.1.12FREG4—Flash Region 4 (Platform Data) Register (SPI Memory Mapped Configuration Registers).......................................... 830 22.1.13PR0—Protected Range 0 Register (SPI Memory Mapped Configuration Registers).......................................... 830 22.1.14PR1—Protected Range 1 Register (SPI Memory Mapped Configuration Registers).......................................... 831 30 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 22.2 22.1.15PR2—Protected Range 2 Register (SPI Memory Mapped Configuration Registers) ......................................... 832 22.1.16PR3—Protected Range 3 Register (SPI Memory Mapped Configuration Registers) ......................................... 833 22.1.17PR4—Protected Range 4 Register (SPI Memory Mapped Configuration Registers) ......................................... 834 22.1.18SSFS—Software Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers) ......................................... 835 22.1.19SSFC—Software Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers) ......................................... 836 22.1.20PREOP—Prefix Opcode Configuration Register (SPI Memory Mapped Configuration Registers) ......................................... 837 22.1.21OPTYPE—Opcode Type Configuration Register (SPI Memory Mapped Configuration Registers) ......................................... 837 22.1.22OPMENU—Opcode Menu Configuration Register (SPI Memory Mapped Configuration Registers) ......................................... 838 22.1.23BBAR—BIOS Base Address Configuration Register (SPI Memory Mapped Configuration Registers) ......................................... 839 22.1.24FDOC—Flash Descriptor Observability Control Register (SPI Memory Mapped Configuration Registers) ......................................... 839 22.1.25FDOD—Flash Descriptor Observability Data Register (SPI Memory Mapped Configuration Registers) ......................................... 840 22.1.26AFC—Additional Flash Control Register (SPI Memory Mapped Configuration Registers) ......................................... 840 22.1.27LVSCC— Host Lower Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) ......................................... 841 22.1.28UVSCC— Host Upper Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) ......................................... 842 22.1.29FPB — Flash Partition Boundary (SPI Memory Mapped Configuration Registers) ......................................... 844 Flash Descriptor Registers ................................................................................ 845 22.2.1 Flash Descriptor Content ....................................................................... 845 22.2.1.1 FLVALSIG - Flash Valid Signature Register (Flash Descriptor Registers) ..................................................... 845 22.2.1.2 FLMAP0 - Flash Map 0 Register (Flash Descriptor Registers).......... 845 22.2.1.3 FLMAP1—Flash Map 1 Register (Flash Descriptor Registers) .......... 846 22.2.1.4 FLMAP2—Flash Map 2 Register (Flash Descriptor Registers) .......... 846 22.2.2 Flash Descriptor Component Section ....................................................... 847 22.2.2.1 FLCOMP—Flash Components Register (Flash Descriptor Registers) ..................................................... 847 22.2.2.2 FLILL—Flash Invalid Instructions Register (Flash Descriptor Registers) ..................................................... 849 22.2.2.3 FLPB—Flash Partition Boundary Register (Flash Descriptor Registers) ..................................................... 849 22.2.3 Flash Descriptor Region Section ............................................................. 850 22.2.3.1 FLREG0—Flash Region 0 Register (Flash Descriptor Registers) ...... 850 22.2.3.2 FLREG1—Flash Region 1 (BIOS) Register (Flash Descriptor Registers) ..................................................... 850 22.2.3.3 FLREG2—Flash Region 2 (ME) Register (Flash Descriptor Registers) ..................................................... 851 22.2.3.4 FLREG3—Flash Region 3 (GbE) Register (Flash Descriptor Registers) ..................................................... 851 22.2.3.5 FLREG4—Flash Region 4 (Platform Data) Register (Flash Descriptor Registers) ..................................................... 851 22.2.4 Flash Descriptor Master Section.............................................................. 852 22.2.4.1 FLMSTR1—Flash Master 1 (Host CPU/ BIOS) (Flash Descriptor Registers) ..................................................... 852 22.2.4.2 FLMSTR2—Flash Master 2 (ME) (Flash Descriptor Registers) ......... 853 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 31 22.3 22.4 23 32 22.2.4.3 FLMSTR3—Flash Master 3 (GbE) (Flash Descriptor Registers) ........ 854 22.2.5 Descriptor Upper Map Section................................................................. 855 22.2.5.1 FLUMAP1—Flash Upper Map 1 (Flash Descriptor Registers)............ 855 22.2.6 ME Vendor Specific Component Capabilities Table ..................................... 856 22.2.6.1 JID0—JEDEC-ID 0 Register (Flash Descriptor Registers) ............... 856 22.2.6.2 VSCC0—Vendor Specific Component Capabilities 0 (Flash Descriptor Registers)...................................................... 856 22.2.6.3 JIDn—JEDEC-ID Register n (Flash Descriptor Registers)................ 858 22.2.6.4 VSCCn—Vendor Specific Component Capabilities n (Flash Descriptor Registers)...................................................... 858 OEM Section ................................................................................................... 860 GbE SPI Flash Program Registers ....................................................................... 860 22.4.1 GLFPR –Gigabit LAN Flash Primary Region Register (GbE LAN Memory Mapped Configuration Registers) .................................. 861 22.4.2 HSFS—Hardware Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers) .................................. 862 22.4.3 HSFC—Hardware Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers) .................................. 863 22.4.4 FADDR—Flash Address Register (GbE LAN Memory Mapped Configuration Registers) .................................. 863 22.4.5 FDATA0—Flash Data 0 Register (GbE LAN Memory Mapped Configuration Registers) .................................. 864 22.4.6 FRAP—Flash Regions Access Permissions Register (GbE LAN Memory Mapped Configuration Registers) .................................. 865 22.4.7 FREG0—Flash Region 0 (Flash Descriptor) Register (GbE LAN Memory Mapped Configuration Registers) .................................. 866 22.4.8 FREG1—Flash Region 1 (BIOS Descriptor) Register (GbE LAN Memory Mapped Configuration Registers) .................................. 866 22.4.9 FREG2—Flash Region 2 (ME) Register (GbE LAN Memory Mapped Configuration Registers) .................................. 866 22.4.10FREG3—Flash Region 3 (GbE) Register (GbE LAN Memory Mapped Configuration Registers) .................................. 867 22.4.11PR0—Protected Range 0 Register (GbE LAN Memory Mapped Configuration Registers) .................................. 867 22.4.12PR1—Protected Range 1 Register (GbE LAN Memory Mapped Configuration Registers) .................................. 868 22.4.13SSFS—Software Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers) .................................. 869 22.4.14SSFC—Software Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers) .................................. 870 22.4.15PREOP—Prefix Opcode Configuration Register (GbE LAN Memory Mapped Configuration Registers) .................................. 871 22.4.16OPTYPE—Opcode Type Configuration Register (GbE LAN Memory Mapped Configuration Registers) .................................. 871 22.4.17OPMENU—Opcode Menu Configuration Register (GbE LAN Memory Mapped Configuration Registers) .................................. 872 Thermal Sensor Registers (D31:F6) ....................................................................... 873 23.1 PCI Bus Configuration Registers......................................................................... 873 23.1.1 VID—Vendor Identification ..................................................................... 874 23.1.2 DID—Device Identification ..................................................................... 874 23.1.3 CMD—Command................................................................................... 874 23.1.4 STS—Status......................................................................................... 875 23.1.5 RID—Revision Identification ................................................................... 875 23.1.6 PI— Programming Interface ................................................................... 875 23.1.7 SCC—Sub Class Code ............................................................................ 876 23.1.8 BCC—Base Class Code........................................................................... 876 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 23.2 23.1.9 CLS—Cache Line Size............................................................................ 876 23.1.10LT—Latency Timer................................................................................ 876 23.1.11HTYPE—Header Type ............................................................................ 876 23.1.12BIST—Built-in Self Test ......................................................................... 877 23.1.13TBAR—Thermal Base ............................................................................ 877 23.1.14TBARH—Thermal Base High DWord......................................................... 877 23.1.15SVID—Subsystem Vendor ID ................................................................. 878 23.1.16SID—Subsystem ID .............................................................................. 878 23.1.17CAP_PTR —Capabilities Pointer............................................................... 878 23.1.18INTLN—Interrupt Line ........................................................................... 878 23.1.19INTPN—Interrupt Pin ............................................................................ 879 23.1.20TBARB—BIOS Assigned Thermal Base Address ......................................... 879 23.1.21TBARBH—BIOS Assigned Thermal Base High DWord ................................. 879 23.1.22PID—PCI Power Management Capability ID .............................................. 880 23.1.23PC—Power Management Capabilities ....................................................... 880 23.1.24PCS—Power Management Control And Status ........................................... 881 Thermal Memory Mapped Configuration Registers (Thermal Sensor - D31:F26)........ 882 23.2.1 TSxE—Thermal Sensor [1:0] Enable ....................................................... 882 23.2.2 TSxS—Thermal Sensor[1:0] Status......................................................... 883 23.2.3 TSxTTP—Thermal Sensor [1:0] Catastrophic Trip Point .............................. 883 23.2.4 TSxCO—Thermal Sensor [1:0] Catastrophic Lock-Down............................. 883 23.2.5 TSxPC—Thermal Sensor [1:0] Policy Control ............................................ 884 23.2.6 TSxLOCK—Thermal Sensor [1:0] Register Lock Control ............................. 884 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 33 Figures 2-1 Intel® ICH9 Interface Signals Block Diagram (Desktop) .................................................56 2-2 Intel® ICH9 Interface Signals Block Diagram (Mobile) ...................................................57 2-3 Example External RTC Circuit .....................................................................................90 4-1 Desktop Conceptual System Clock Diagram................................................................ 108 4-2 Mobile Conceptual Clock Diagram ............................................................................. 108 5-1 Generation of SERR# to Platform.............................................................................. 115 5-2 LPC Interface Diagram ............................................................................................ 123 5-3 Intel® ICH9 DMA Controller ..................................................................................... 128 5-4 DMA Request Assertion through LDRQ#..................................................................... 132 5-5 Coprocessor Error Timing Diagram............................................................................ 157 5-6 TCO Legacy/Compatible Mode SMBus Configuration .................................................... 188 5-7 Advanced TCO Intel® AMT Mode SMBus/SMLink Configuration ...................................... 189 5-8 Advanced TCO BMC Mode SMBus/SMLink Configuration ............................................... 190 5-9 Serial Post over GPIO Reference Circuit ..................................................................... 191 5-10SATA Power States ................................................................................................. 198 5-11Flow for Port Enable / Device Present Bits .................................................................. 200 5-12Serial Data transmitted over the SGPIO Interface ....................................................... 205 5-13USB Legacy Keyboard Flow Diagram ......................................................................... 214 5-14 Intel® ICH9-USB Port Connections Default Six and Six Configuration............................ 222 5-15 Intel® ICH9-USB Port Connections Eight and Four Configuration .................................. 222 5-16Flash Partition Boundary.......................................................................................... 251 5-17Flash Descriptor Sections......................................................................................... 252 6-1 Intel® ICH9 Ballout (Top view–Left Side) (Desktop Only) ............................................. 264 6-2 Intel® ICH9 Ballout (Top view–Right Side) (Desktop Only) ........................................... 265 6-3 Intel® ICH9M and ICH9M-E Ballout (Top View–Left Side) (Mobile Only).......................... 273 6-4 Intel® ICH9M and ICH9M-E Ballout (Top View–Right Side) (Mobile Only)........................ 274 6-5 Intel® ICH9M SFF Preliminary Ballout(Top view–Left Side) ........................................... 282 6-6 Intel® ICH9M-SFF Preliminary Ballout(Top view–Right Side)......................................... 283 7-1 Intel® ICH9 Package (Top View)............................................................................... 289 7-2 Intel® ICH9 Package (Bottom View).......................................................................... 290 7-3 Intel® ICH9 Package (Side View) .............................................................................. 290 7-4 Intel® ICH9M Package (Top View) ............................................................................ 291 7-5 Intel® ICH9M Package (Bottom View) ....................................................................... 292 7-6 Intel® ICH9M Package (Side View) ........................................................................... 292 7-7 Intel® ICH9M-SSF Package Drawing ......................................................................... 293 8-1 Clock Timing .......................................................................................................... 321 8-2 Valid Delay from Rising Clock Edge ........................................................................... 321 8-3 Setup and Hold Times ............................................................................................. 321 8-4 Float Delay ............................................................................................................ 322 8-5 Pulse Width ........................................................................................................... 322 8-6 Output Enable Delay ............................................................................................... 322 8-7 USB Rise and Fall Times .......................................................................................... 322 8-8 USB Jitter.............................................................................................................. 323 8-9 USB EOP Width ...................................................................................................... 323 8-10SMBus Transaction ................................................................................................. 323 8-11SMBus Timeout ...................................................................................................... 324 8-12SPI Timings ........................................................................................................... 324 8-13Intel® High Definition Audio Input and Output Timings ................................................ 325 8-14Power Sequencing and Reset Signal Timings .............................................................. 325 8-15G3 (Mechanical Off) to S0 Timings ............................................................................ 326 8-16S0 to S1 to S0 Timing ............................................................................................. 327 8-17S0 to S5 to S0 Timings (Desktop Only) ..................................................................... 327 8-18S0 to S5 to S0 Timings (Mobile Only) ........................................................................ 328 34 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 8-19C0 to C2 to C0 Timings (Mobile Only) ....................................................................... 328 8-20C0 to C3 to C0 Timings (Mobile Only) ....................................................................... 329 8-21C0 to C4 to C0 Timings (Mobile Only) ....................................................................... 329 8-22C0 to C5/C6 to C0 Timings (Mobile Only) .................................................................. 330 8-23Sleep control signal relationship - Host boots and Management Engine off ..................... 330 8-24Sleep control signal relationship - Host and Management Engine boot after G3 ............... 331 8-25Sleep control signal relationship - Host stays in S5 and Management Engine boots after G3 ............................................................................................. 331 8-26S4, S5/M1 to S0/M0 ............................................................................................... 332 8-27S0 to G3 Timings (Desktop Only) ............................................................................. 332 8-28S0 to G3 Timings (Mobile Only)................................................................................ 332 Tables 1-1 Industry Specifications.............................................................................................. 43 1-2 Intel Specification .................................................................................................... 44 1-3 PCI Devices and Functions......................................................................................... 47 1-4 Intel® ICH9 Desktop/Server Family ............................................................................ 54 1-5 Intel® ICH9 Mobile Family ......................................................................................... 54 2-1 Direct Media Interface Signals ................................................................................... 58 2-2 PCI Express* Signals ................................................................................................ 59 2-3 LAN Connect Interface Signals ................................................................................... 59 2-4 Gigabit LAN Connect Interface Signals ........................................................................ 60 2-5 Firmware Hub Interface Signals ................................................................................. 61 2-6 PCI Interface Signals ................................................................................................ 62 2-7 Serial ATA Interface Signals ...................................................................................... 64 2-8 LPC Interface Signals................................................................................................ 67 2-9 Interrupt Signals...................................................................................................... 68 2-10USB Interface Signals ............................................................................................... 69 2-11Power Management Interface Signals ......................................................................... 71 2-12Processor Interface Signals ....................................................................................... 74 2-13SM Bus Interface Signals .......................................................................................... 75 2-14System Management Interface Signals........................................................................ 76 2-15Real Time Clock Interface ......................................................................................... 78 2-16Other Clocks ........................................................................................................... 78 2-17Miscellaneous Signals ............................................................................................... 78 2-18Intel® High Definition Audio Link Signals .................................................................... 80 2-19Serial Peripheral Interface (SPI) Signals ...................................................................... 81 2-20Controller Link Signals .............................................................................................. 82 2-21Intel® Quiet System Technology Signals..................................................................... 83 2-22General Purpose I/O Signals ...................................................................................... 83 2-23Power and Ground Signals......................................................................................... 86 2-24Functional Strap Definitions....................................................................................... 88 3-1 Integrated Pull-Up and Pull-Down Resistors ................................................................. 91 3-2 Power Plane and States for Output and I/O Signals for Desktop Configurations................. 93 3-3 Power Plane and States for Output and I/O Signals for Mobile Configurations ................... 97 3-4 Power Plane for Input Signals for Desktop Configurations ............................................ 102 3-5 Power Plane for Input Signals for Mobile Configurations............................................... 104 4-1 Intel® ICH9 and System Clock Domains .................................................................... 107 5-1 PCI Bridge Initiator Cycle Types ............................................................................... 109 5-2 Type 1 Address Format ........................................................................................... 112 5-3 MSI vs. PCI IRQ Actions .......................................................................................... 114 5-4 LAN Mode Support ................................................................................................. 119 5-5 LPC Cycle Types Supported ..................................................................................... 124 5-6 Start Field Bit Definitions ........................................................................................ 124 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 35 5-7 Cycle Type Bit Definitions ........................................................................................ 125 5-8 Transfer Size Bit Definition ...................................................................................... 125 5-9 SYNC Bit Definition ................................................................................................. 126 5-10DMA Transfer Size .................................................................................................. 130 5-11Address Shifting in 16-Bit I/O DMA Transfers ............................................................. 130 5-12Counter Operating Modes ........................................................................................ 136 5-13Interrupt Controller Core Connections ....................................................................... 138 5-14Interrupt Status Registers ....................................................................................... 139 5-15Content of Interrupt Vector Byte .............................................................................. 139 5-16APIC Interrupt Mapping1 ......................................................................................... 145 5-17Interrupt Message Address Format ........................................................................... 147 5-18Interrupt Message Data Format ................................................................................ 148 5-19Stop Frame Explanation .......................................................................................... 150 5-20Data Frame Format ................................................................................................ 151 5-21Configuration Bits Reset by RTCRST# Assertion .......................................................... 154 5-22INIT# Going Active................................................................................................. 156 5-23NMI Sources .......................................................................................................... 157 5-24DP Signal Differences.............................................................................................. 158 5-25General Power States for Systems Using Intel® ICH9 .................................................. 160 5-26State Transition Rules for Intel® ICH9 ....................................................................... 161 5-27System Power Plane ............................................................................................... 162 5-28Causes of SMI# and SCI ......................................................................................... 163 5-29Break Events ......................................................................................................... 166 5-30Sleep Types........................................................................................................... 170 5-31Causes of Wake Events ........................................................................................... 171 5-32GPI Wake Events.................................................................................................... 172 5-33Transitions Due to Power Failure............................................................................... 173 5-34Transitions Due to Power Button............................................................................... 174 5-35Transitions Due to RI# Signal .................................................................................. 175 5-36Write Only Registers with Read Paths in ALT Access Mode ............................................ 178 5-37PIC Reserved Bits Return Values............................................................................... 180 5-38Register Write Accesses in ALT Access Mode .............................................................. 180 5-39Intel® ICH9 Clock Inputs ......................................................................................... 183 5-40Causes of Host and Global Resets ............................................................................. 185 5-41Event Transitions that Cause Messages ..................................................................... 188 5-42Multi-activity LED Message Type............................................................................... 204 5-43Legacy Replacement Routing ................................................................................... 207 5-44Bits Maintained in Low Power States ......................................................................... 213 5-45USB Legacy Keyboard State Transitions..................................................................... 215 5-46UHCI vs. EHCI ....................................................................................................... 217 5-47Debug Port Behavior ............................................................................................... 226 5-48I2C Block Read....................................................................................................... 234 5-49Enable for SMBALERT# ........................................................................................... 236 5-50Enables for SMBus Slave Write and SMBus Host Events ............................................... 236 5-51Enables for the Host Notify Command ....................................................................... 237 5-52Slave Write Registers .............................................................................................. 238 5-53Command Types .................................................................................................... 239 5-54Slave Read Cycle Format ......................................................................................... 240 5-55Data Values for Slave Read Registers ........................................................................ 240 5-56Host Notify Format ................................................................................................. 243 5-57Region Size versus Erase Granularity of Flash Components .......................................... 251 5-58Region Access Control Table .................................................................................... 253 5-59Hardware Sequencing Commands and Opcode Requirements ....................................... 256 5-60Flash Protection Mechanism Summary....................................................................... 257 5-61Recommended Pinout for 8-Pin Serial Flash Device ..................................................... 258 36 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 5-62Recommended Pinout for 16-Pin Serial Flash Device ................................................... 259 6-1 Intel® ICH9 Ballout by Signal Name (Desktop Only) ................................................... 266 6-2 Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) ................................ 275 6-3 Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) ........................................... 284 8-1 Intel® ICH9 Absolute Maximum Ratings .................................................................... 295 8-2 DC Current Characteristics1 (Desktop Only)............................................................... 295 8-3 Preliminary DC Current Characteristics (Mobile Only)1 ................................................ 297 8-4 DC Characteristic Input Signal Association ................................................................. 298 8-5 DC Input Characteristics ......................................................................................... 300 8-6 DC Characteristic Output Signal Association............................................................... 302 8-7 DC Output Characteristics ....................................................................................... 304 8-8 Other DC Characteristics ......................................................................................... 306 8-9 Clock Timings ........................................................................................................ 308 8-10PCI Interface Timing............................................................................................... 309 8-11Universal Serial Bus Timing ..................................................................................... 310 8-12SATA Interface Timings .......................................................................................... 311 8-13SMBus Timing ....................................................................................................... 312 8-14Intel® High Definition Audio Timing .......................................................................... 312 8-15LPC Timing............................................................................................................ 313 8-16Miscellaneous Timings ............................................................................................ 313 8-17SPI Timings (20 MHz) ............................................................................................. 313 8-18SPI Timings (33 MHz) ............................................................................................. 314 8-19SST Timings .......................................................................................................... 314 8-20PECI Timings......................................................................................................... 315 8-21Power Sequencing and Reset Signal Timings.............................................................. 315 8-22Power Management Timings .................................................................................... 317 9-1 PCI Devices and Functions....................................................................................... 334 9-2 Fixed I/O Ranges Decoded by Intel® ICH9................................................................. 336 9-3 Variable I/O Decode Ranges .................................................................................... 338 9-4 Memory Decode Ranges from Processor Perspective ................................................... 339 10-1Chipset Configuration Register Memory Map (Memory Space) ...................................... 343 11-1PCI Bridge Register Address Map (PCI-PCI—D30:F0) .................................................. 395 12-1Gigabit LAN Configuration Registers Address Map (Gigabit LAN —D25:F0) ..................... 411 12-2Gigabit LAN Base Address A Registers Address Map (Gigabit LAN— D25:F0) .................. 424 13-1LPC Interface PCI Register Address Map (LPC I/F—D31:F0) ......................................... 427 13-2DMA Registers ....................................................................................................... 452 13-3PIC Registers (LPC I/F—D31:F0) .............................................................................. 465 13-4APIC Direct Registers (LPC I/F—D31:F0) ................................................................... 474 13-5APIC Indirect Registers (LPC I/F—D31:F0)................................................................. 474 13-6RTC I/O Registers .................................................................................................. 479 13-7RTC (Standard) RAM Bank ...................................................................................... 480 13-8Processor Interface PCI Register Address Map (LPC I/F—D31:F0) ................................. 484 13-9Power Management PCI Register Address Map (PM—D31:F0) ....................................... 487 13-10APM Register Map ................................................................................................ 500 13-11ACPI and Legacy I/O Register Map.......................................................................... 501 13-12TCO I/O Register Address Map ............................................................................... 526 13-13Registers to Control GPIO Address Map ................................................................... 534 14-1SATA Controller PCI Register Address Map (SATA–D31:F2) .......................................... 541 14-2Bus Master IDE I/O Register Address Map ................................................................. 568 14-3AHCI Register Address Map ..................................................................................... 577 14-4Generic Host Controller Register Address Map ............................................................ 578 14-5Port [5:0] DMA Register Address Map ....................................................................... 586 15-1SATA Controller PCI Register Address Map (SATA–D31:F5) .......................................... 605 15-2Bus Master IDE I/O Register Address Map ................................................................. 622 15-3AHCI Index Data Pair Register Map .......................................................................... 625 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 37 16-1UHCI Controller PCI Configuration Map ...................................................................... 631 16-2UHCI Controller PCI Register Address Map (USB—D29:F0/F1/F2/F3, D26:F0/F1/F2) ................................................................... 631 16-3USB I/O Registers .................................................................................................. 644 16-4Run/Stop, Debug Bit Interaction SWDBG (Bit 5), Run/Stop (Bit 0) Operation .................. 647 17-1USB EHCI PCI Register Address Map (USB EHCI—D29:F7, D26:F7) ............................... 655 17-2Enhanced Host Controller Capability Registers ............................................................ 676 17-3Enhanced Host Controller Operational Register Address Map ........................................ 680 17-4Debug Port Register Address Map ............................................................................. 694 18-1Intel® High Definition Audio PCI Register Address Map (Intel® High Definition Audio D27:F0) ....................................................................... 699 18-2Intel® High Definition Audio PCI Register Address Map (Intel® High Definition Audio D27:F0) ....................................................................... 722 19-1SMBus Controller PCI Register Address Map (SMBus—D31:F3) ..................................... 751 19-2SMBus I/O and Memory Mapped I/O Register Address Map .......................................... 758 20-1PCI Express* Configuration Registers Address Map (PCI Express—D28:F0/F1/F2/F3/F4/F5)..................................................................... 769 21-1Memory-Mapped Registers....................................................................................... 815 22-1Serial Peripheral Interface (SPI) Register Address Map (SPI Memory Mapped Configuration Registers) ........................................................... 821 22-2Gigabit LAN SPI Flash Program Register Address Map (GbE LAN Memory Mapped Configuration Registers) .................................................... 860 23-1Thermal Sensor Register Address Map....................................................................... 873 38 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Revision History Revision Number Description -001 • Initial release -002 • Added spcifications for Intel® 82801IO ICH9DO -003 • • Added mobile family – Intel 82801IBM ICH9M and 82801IEM ICH9M-E Added specification update information. -004 • Added ICH9M-SFF ICH9-I/O Controller Hub Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Revision Date June 2007 August 2007 July 2008 August 2008 39 Intel® ICH9 Features 40 Direct Media Interface — 10 Gb/s each direction, full duplex — Transparent to software PCI Express* — 6 PCI Express root ports — Supports PCI Express 1.1 — Ports 1-4 can be statically configured as 4x1, or 1x4 — Support for full 2.5 Gb/s bandwidth in each direction per x1 lane — Module based Hot-Plug supported (e.g., ExpressCard*) PCI Bus Interface — Supports PCI Rev 2.3 Specification at 33 MHz — Four available PCI REQ/GNT pairs — Support for 64-bit addressing on PCI using DAC protocol Integrated Serial ATA Host Controller — Up to six SATA ports — Data transfer rates up to 3.0 Gb/s (300 MB/s). — Integrated AHCI controller External SATA support — NEW: Port Disable Capability Intel® Matrix Storage Technology (ICH9R, ICH9DH, ICH9DO, ICH9M, and ICH9M-E only) — Configures the ICH9 SATA Controller as an AHCI controller — Configures the ICH9 SATA controller as a RAID controller supporting RAID 0/1/5/10 (Except ICH9M) Intel® High Definition Audio Interface — PCI Express endpoint — Independent Bus Master logic for eight general purpose streams: four input and four output — Support four external Codecs — Supports variable length stream slots — Supports multichannel, 32-bit sample depth, 192 kHz sample rate output — Provides mic array support — Allows for non-48 kHz sampling output — Support for ACPI Device States — Low Voltage Mode — Docking Support (ICH9M only) Intel® Quiet System Technology (Desktop only) — Four TACH signals and three PWM signals — NEW: Improved algorithms for better performance Simple Serial Transport (SST) 1.0 Bus and Platform Environmental Control Interface (PECI) (Desktop only) USB 2.0 — NEW: Six UHCI Host Controllers, supporting up to twelve external ports — Two EHCI Host Controllers, supporting up to twelve external ports — Two Configuration Options for EHCI Controllers 6+6 and 8+4 — Per-Port-Disable Capability — Includes up to two USB 2.0 High-speed Debug Ports — Supports wake-up from sleeping states S1–S4 — Supports legacy Keyboard/Mouse software Integrated Gigabit LAN Controller — Integrated ASF Management Controller — Network security with System Defense — Supports IEEE 802.3 — LAN Connect Interface (LCI) and Gigabit LAN Connect Interface (GLCI) — 10/100/1000 Mbps Ethernet Support — NEW: Jumbo Frame Support Intel® Active Management Technology with System Defense (Digital Office only) — NEW: Network Outbreak Containment Heuristics Intel® I/O Virtualization (VT-d) support Intel® Trusted Execution Technology support Power Management Logic — Supports ACPI 3.0b — ACPI-defined power states (C1, C2, S1, S3–S5 for Desktop and C1–C6, S1, S3–S5 for Mobile) — ACPI Power Management Timer — (Mobile Only) Support for “Intel SpeedStep® Technology” processor power control and “Deeper Sleep” power state — PCI CLKRUN# (Mobile only) and PME# support — SMI# generation — All registers readable/restorable for proper resume from 0 V suspend states — Support for APM-based legacy power management for non-ACPI Desktop and Mobile implementations External Glue Integration — Integrated Pull-up, Pull-down and Series Termination resistors on processor I/F — Integrated Pull-down and Series resistors on USB Enhanced DMA Controller — Two cascaded 8237 DMA controllers — Supports LPC DMA Intel® I/O Controller Hub 9 (ICH9) Family Datasheet SMBus — Faster speed, up to 100 kbps — Flexible SMBus/SMLink architecture to optimize for ASF — Provides independent manageability bus through SMLink interface — Supports SMBus 2.0 Specification — Host interface allows processor to communicate via SMBus — Slave interface allows an internal or external Microcontroller to access system resources — Compatible with most two-wire components that are also I2C compatible High Precision Event Timers — Advanced operating system interrupt scheduling Timers Based on 82C54 — System timer, Refresh request, Speaker tone output Real-Time Clock — 256-byte battery-backed CMOS RAM — Integrated oscillator components — Lower Power DC/DC Converter implementation System TCO Reduction Circuits — Timers to generate SMI# and Reset upon detection of system hang — Timers to detect improper processor reset — Integrated processor frequency strap logic — Supports ability to disable external devices Interrupt Controller — Supports up to eight PCI interrupt pins — Supports PCI 2.3 Message Signaled Interrupts — Two cascaded 82C59 with 15 interrupts — Integrated I/O APIC capability with 24 interrupts — Supports Processor System Bus interrupt delivery 1.05 V operation with 1.5 and 3.3 V I/O — 5 V tolerant buffers on PCI, USB and selected Legacy signals 1.05 V Core Voltage Five Integrated Voltage Regulators for different power rails Firmware Hub I/F supports BIOS Memory size up to 8 MBytes Serial Peripheral Interface (SPI) — Supports up to two SPI devices — Supports 20 MHz and 33 MHz SPI devices — NEW: Dual erase support Low Pin Count (LPC) I/F — Supports two Master/DMA devices. — Support for Security Device (Trusted Platform Module) connected to LPC. GPIO — TTL, Open-Drain, Inversion — NEW: GPIO lock down Package 31x31 mm mixed-pitch 676 mBGA — Different footprint for Mobile Note: Not all features are available on all ICH9 components. See Section 1.3 for more details. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 41 Desktop Configuration DMI (To (G)MCH) USB 2.0 Power Management (Supports 12 USB ports Dual EHCI Controller) Clock Generator SATA (6 ports) System Management (TCO) Intel® ICH9 Intel® High Definition Audio Codec(s) SMBus 2.0/I2C PCI Express* x1 ® Intel Gigabit Ethernet Phy SPI BIOS Flash PCI Bus GLCI S L O T LCI GPIO LPC I/F S L O T ... Other ASICs Super I/O (Optional) TPM Firmware Hub (Optional) Mobile Configuration DMI (T o (G )M C H ) U S B 2 .0 (S u p p o rts 1 2 U S B p o rts D u a l E H C I C o n tro lle rs ) Pow er M anagem ent C lo c k G e n e ra to r S y s te m M a n a g e m e n t (T C O ) ® S A T A (4 p o rts ) In te l IC H 9 M In te l® H ig h D e fin itio n A u d io C o d e c (s ) S M B u s 2 .0 /I 2 C PCI Bus D o c k in g B rid g e P C I E x p re s s x 1 In te l® G ig a b it E th e rn e t P h y C a rd b u s C o n tro lle r (& a tta c h e d s lo ts ) G LC I LC I G P IO O th e r A S IC s (O p tio n a l) L P C I/F S P I F la s h S u p e r I/O TPM (O p tio n a l) F la s h B IO S §§ 42 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction 1 Introduction This document is intended for Original Equipment Manufacturers and BIOS vendors creating Intel® I/O Controller Hub 9 (ICH9) Family based products. This document is for the following components: • Intel® 82801IB ICH9 (ICH9) • Intel® 82801IR ICH9 RAID (ICH9R) • Intel® 82801IH ICH9 Digital Home (ICH9DH) • Intel® 82801IO ICH9 Digital Office (ICH9DO) • Intel® 82801IBM ICH9 Mobile (ICH9M) • Intel® 82801IEM ICH9 Mobile Enhanced (ICH9M-E) Section 1.3 provides high-level feature differences for the ICH9 Family components. Note: Throughout this document, ICH9 is used as a general ICH9 term and refers to the Intel 82801IB ICH9, Intel 82801IR ICH9R, and Intel 82801IH ICH9DH, and Intel 82801IO ICH9DO, Intel 82801IBM ICH9M, and Intel 82801IEM ICH9M-E components, unless specifically noted otherwise. Note: Throughout this document, the term “Desktop” refers to any implementation using a desktop version of the ICH9 (e.g. ICH9R), be it in a desktop, server, workstation, etc., unless specifically noted otherwise. Note: Throughout this document, the term “Desktop Only” refers to information that is for the Intel 82801IB ICH9, Intel 82801IR ICH9R, and Intel 82801IH ICH9DH, and Intel 82801IO ICH9DO unless specifically noted otherwise. The term “Digital Home Only“refers to information that is for the Intel 82801IH ICH9DH, unless specifically noted otherwise. The term “Digital Office Only“ refers to information that is for the Intel 82801IO ICH9DO and Intel 82801IBM ICH9M-E, unless specifically noted otherwise. The term “Mobile Only” refers to information that is for both the Intel 82801IBM ICH9M and Intel 82801IEM ICH9M-E, unless noted otherwise. 1.1 About This Document This document is intended for Original Equipment Manufacturers and BIOS vendors creating Intel® ICH9 family-based products (See Section 1.3 for currently defined ICH9 components). This document assumes a working knowledge of the vocabulary and principles of PCI Express*, USB, AHCI, SATA, Intel® High Definition Audio (Intel® HD Audio), SMBus, PCI, ACPI and LPC. Although some details of these features are described within this manual, refer to the individual industry specifications listed in Table 1-1 for the complete details. Table 1-1. Industry Specifications Specification Location PCI Express* Base Specification, Revision 1.1 http://www.pcisig.com/specifications Low Pin Count Interface Specification, Revision 1.1 (LPC) http://developer.intel.com/design/chipsets/ industry/lpc.htm System Management Bus Specification, Version 2.0 (SMBus) http://www.smbus.org/specs/ Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 43 Introduction Table 1-1. Industry Specifications Specification Location PCI Local Bus Specification, Revision 2.3 (PCI) http://www.pcisig.com/specifications PCI Mobile Design Guide, Revision 1.1 http://www.pcisig.com/specifications PCI Power Management Specification, Revision 1.1 http://www.pcisig.com/specifications Universal Serial Bus Specification (USB), Revision 2.0 http://www.usb.org/developers/docs Advanced Configuration and Power Interface, Version 3.0b (ACPI) http://www.acpi.info/spec.htm Universal Host Controller Interface, Revision 1.1 (UHCI) http://developer.intel.com/technology/USB/ UHCI11D.htm Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 (EHCI) http://developer.intel.com/technology/usb/ ehcispec.htm Serial ATA Specification, Revision 1.0a http://www.serialata.org/specifications.asp Serial ATA II: Extensions to Serial ATA 1.0, Revision 1.0 http://www.serialata.org/specifications.asp Serial ATA II Cables and Connectors Volume 2 Gold http://www.serialata.org/specifications.asp Alert Standard Format Specification, Version 1.03 http://www.dmtf.org/standards/asf IEEE 802.3 Fast Ethernet http://standards.ieee.org/getieee802/ IA-PC HPET (High Precision Event Timers) Specification, Revision 0.98a http://www.intel.com/technology/architecture/ hpetspec.htm TPM Specification 1.02, Level 2 Revision 103 http://www.trustedcomputinggroup.org/specs/ TPM Document users may also need to reference the following Intel Specification listed in Table 1-2 when using this document. Table 1-2. Intel Specification Specification 44 Location Intel® I/O Controller Hub (ICH9) Family Datasheet Specification Update www.intel.com/design/chipsets/ specupdt/316973.htm Intel® I/O Controller Hub (ICH9) Thermal and Mechanical Design Guide www.intel.com/design/chipsets/ designex/316974.htm Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction Chapter 1. Introduction Chapter 1 introduces the ICH9 and provides information on manual organization and gives a general overview of the ICH9. Chapter 2. Signal Description Chapter 2 provides a block diagram of the ICH9/ICH9M and a detailed description of each signal. Signals are arranged according to interface and details are provided as to the drive characteristics (Input/Output, Open Drain, etc.) of all signals. Chapter 3. Intel® ICH9 Pin States Chapter 3 provides a complete list of signals, their associated power well, their logic level in each suspend state, and their logic level before and after reset. Chapter 4. Intel® ICH9 and System Clock Domains Chapter 4 provides a list of each clock domain associated with the ICH9 in an ICH9 based system. Chapter 5. Functional Description Chapter 5 provides a detailed description of the functions in the ICH9. All PCI buses, devices and functions in this manual are abbreviated using the following nomenclature; Bus:Device:Function. This manual abbreviates a bus as B0, devices as D25, D26, D27, D28, D29, D30 and D31 and functions as F0, F1, F2, F3, F4, F5, F6 and F7. For example Device 31 Function 0 is abbreviated as D31:F0, Bus 0 Device 25 Function 0 is abbreviated as B0:D25:F0. Generally, the bus number will not be used, and can be considered to be Bus 0. Note that the ICH9’s external PCI bus is typically Bus 1, but may be assigned a different number depending upon system configuration. Chapter 6. Ballout Definition Chapter 6 provides a table of each signal and its ball assignment in the 676-mBGA package. Chapter 7. Package Information Chapter 7 provides drawings of the physical dimensions and characteristics of the 676mBGA package. Chapter 8. Electrical Characteristics Chapter 8 provides all AC and DC characteristics including detailed timing diagrams. Chapter 9. Register and Memory Mappings Chapter 9 provides an overview of the registers, fixed I/O ranges, variable I/O ranges and memory ranges decoded by the ICH9. Chapter 10. Chipset Configuration Registers Chapter 10 provides a detailed description of all registers and base functionality that is related to chipset configuration and not a specific interface (such as LPC, PCI, or PCI Express*). It contains the root complex register block, which describes the behavior of the upstream internal link. Chapter 11. PCI-to-PCI Bridge Registers Chapter 11 provides a detailed description of all registers that reside in the PCI-to-PCI bridge. This bridge resides at Device 30, Function 0 (D30:F0). Chapter 12. Integrated LAN Controller Registers Chapter 12 provides a detailed description of all registers that reside in the ICH9’s integrated LAN controller. The integrated LAN Controller resides at Device 25, Function 0 (D25:F0). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 45 Introduction Chapter 13. LPC Bridge Registers Chapter 13 provides a detailed description of all registers that reside in the LPC bridge. This bridge resides at Device 31, Function 0 (D31:F0). This function contains registers for many different units within the ICH9 including DMA, Timers, Interrupts, Processor Interface, GPIO, Power Management, System Management and RTC. Chapter 14. SATA Controller Registers Chapter 14 provides a detailed description of all registers that reside in the SATA controller #1. This controller resides at Device 31, Function 2 (D31:F2). Chapter 15. SATA Controller Registers Chapter 15 provides a detailed description of all registers that reside in the SATA controller #2. This controller resides at Device 31, Function 5 (D31:F5). Chapter 16. UHCI Controller Registers Chapter 16 provides a detailed description of all registers that reside in the six UHCI host controllers. These controllers reside at Device 29, Functions 0, 1, 2, and 3 (D29:F0/F1/F2/F3) and Device 26, Function 0, 1 and 2 (D26:F0/F1/F2). Chapter 17. EHCI Controller Registers Chapter 17 provides a detailed description of all registers that reside in the two EHCI host controllers. These controllers reside at Device 29, Function 7 (D29:F7) and Device 26, Function 7 (D26:F7). Chapter 18. SMBus Controller Registers Chapter 19 provides a detailed description of all registers that reside in the SMBus controller. This controller resides at Device 31, Function 3 (D31:F3). Chapter 19. Intel® High Definition Audio Controller Registers Chapter 18 provides a detailed description of all registers that reside in the Intel High Definition Audio controller. This controller resides at Device 27, Function 0 (D27:F0). Chapter 20. PCI Express* Port Controller Registers Chapter 20 provides a detailed description of all registers that reside in the PCI Express controller. This controller resides at Device 28, Functions 0 to 5 (D28:F0-F5). Chapter 21. High Precision Event Timers Registers Chapter 21 provides a detailed description of all registers that reside in the multimedia timer memory mapped register space. Chapter 22. Serial Peripheral Interface Registers Chapter 22 provides a detailed description of all registers that reside in the SPI memory mapped register space. Chapter 23. Thermal Sensors Chapter 23 provides a detailed description of all registers that reside in the thermal sensors PCI configuration space. The registers reside at Device 31, Function 6 (D31:F6). 46 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction 1.2 Overview The ICH9 provides extensive I/O support. Functions and capabilities include: • PCI Express* Base Specification, Revision 1.1 support • PCI Local Bus Specification, Revision 2.3 support for 33 MHz PCI operations (supports up to four Req/Gnt pairs). • ACPI Power Management Logic Support, Revision 3.0b • Enhanced DMA controller, interrupt controller, and timer functions • Integrated Serial ATA host controllers with independent DMA operation on up to six ports (Desktop only) or four ports (Mobile only) and AHCI support. • USB host interface with support for up to twelve USB ports; six UHCI host controllers; two EHCI high-speed USB 2.0 Host controllers • Integrated 10/100/1000 Gigabit Ethernet MAC with System Defense • System Management Bus (SMBus) Specification, Version 2.0 with additional support for I2C devices • Supports Intel® High Definition Audio • Supports Intel® Matrix Storage Technology (Intel® ICH9R, ICH9DH, ICH9DO, ICH9M, and ICH9M-E Only) • Supports Intel® Active Management Technology (Digital Office only) • Supports Intel® Virtualization Technology for Directed I/O • Supports Intel® Trusted Execution Technology • Low Pin Count (LPC) interface • Firmware Hub (FWH) interface support • Serial Peripheral Interface (SPI) support • Intel® Quiet System Technology (Desktop Only) • Integrated TPM 1.2 (Mobile Only) The Intel ICH9 incorporates a variety of PCI devices and functions, as shown in Table 1-3. They are divided into seven logical devices. The first is the DMI-To-PCI bridge (Device 30). The second device (Device 31) contains most of the standard PCI functions that always existed in the PCI-to-ISA bridges (South Bridges), such as the Intel PIIX4. The third and fourth (Device 29 and Device 26) are the USB host controller devices. The fifth (Device 28) is PCI Express device. The sixth (Device 27) is the HD Audio controller device, and the seventh (Device 25) is the Gigabit Ethernet controller device. Table 1-3. PCI Devices and Functions (Sheet 1 of 2) Bus:Device:Function Function Description Bus 0:Device 30:Function 0 DMI-to-PCI Bridge Bus 0:Device 31:Function 0 LPC Controller1 Bus 0:Device 31:Function 2 SATA Controller #1 Bus 0:Device 31:Function 5 SATA Controller #23 Bus 0:Device 31:Function 6 Thermal Subsystem Bus 0:Device 31:Function 3 SMBus Controller Bus 0:Device 29:Function 0 USB FS/LS UHCI Controller #1 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 47 Introduction Table 1-3. PCI Devices and Functions (Sheet 2 of 2) Bus:Device:Function Function Description Bus 0:Device 29:Function 1 USB FS/LS UHCI Controller #2 Bus 0:Device 29:Function 2 USB FS/LS UHCI Controller #3 Bus 0:Device 29:Function 3 USB FS/LS UHCI Controller #62 Bus 0:Device 29:Function 7 USB HS EHCI Controller #1 Bus 0:Device 26:Function 0 USB FS/LS UHCI Controller #4 Bus 0:Device 26:Function 1 USB FS/LS UHCI Controller #5 Bus 0:Device 26:Function 2 USB FS/LS UHCI Controller #62 Bus 0:Device 26:Fucntion 7 USB HS EHCI Controller #2 Bus 0:Device 28:Function 0 PCI Express* Port 1 Bus 0:Device 28:Function 1 PCI Express Port 2 Bus 0:Device 28:Function 2 PCI Express Port 3 Bus 0:Device 28:Function 3 PCI Express Port 4 Bus 0:Device 28:Function 4 PCI Express Port 5 Bus 0:Device 28:Function 5 PCI Express Port 6 Bus 0:Device 27:Function 0 Intel® High Definition Audio Controller Bus 0:Device 25:Function 0 Gigabit Ethernet Controller NOTES: 1. The PCI-to-LPC bridge contains registers that control LPC, Power Management, System Management, GPIO, Processor Interface, RTC, Interrupts, Timers, and DMA 2. Device 26:Function 2 maybe configured as Device 29:Function 3 during BIOS Post. 3. SATA Controller 2 is only visible when D31:F2 CC.SCC=01h. 48 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction 1.2.1 Capability Overview The following sub-sections provide an overview of the ICH9 capabilities. Direct Media Interface (DMI) Direct Media Interface (DMI) is the chip-to-chip connection between the Memory Controller Hub / Graphics Memory Controller Hub ((G)MCH) and I/O Controller Hub 9 (ICH9). This high-speed interface integrates advanced priority-based servicing allowing for concurrent traffic and true isochronous transfer capabilities. Base functionality is completely software-transparent, permitting current and legacy software to operate normally. PCI Express* Interface The ICH9 provides up to 6 PCI Express Root Ports, supporting the PCI Express Base Specification, Revision 1.1. Each Root Port supports 2.5 GB/s bandwidth in each direction (5 GB/s concurrent). PCI Express Root Ports 1-4 can be statically configured as four x1 Ports or ganged together to form one x4 port. Ports 5 and 6 can only be used as two x1 ports. On Mobile platforms, PCI Express Ports 1-4 can also be configured as one x2 port (using ports 1 and 2) with ports 3 and 4 configured as x1 ports. Note: The integrated Gigabit Ethernet controllers data lines for 1000 Mb/s speed are multiplexed with PCI Express* Root Port 6 and therefore unavailable if a Gigabit Ethernet PHY is connected. The use of a 10/100 Mb/s PHY does not consume PCI Express Root Port 6 and therefore the port is available to be utilized as a x1 Port. Serial ATA (SATA) Controller The ICH9 has two integrated SATA host controllers that support independent DMA operation on up to six ports (desktop only) or four ports (mobile only) and supports data transfer rates of up to 3.0 Gb/s (300 MB/s). The SATA controller contains two modes of operation – a legacy mode using I/O space, and an AHCI mode using memory space. Software that uses legacy mode will not have AHCI capabilities. The ICH9 supports the Serial ATA Specification, Revision 1.0a. The ICH9 also supports several optional sections of the Serial ATA II: Extensions to Serial ATA 1.0 Specification, Revision 1.0 (AHCI support is required for some elements). Note: SATA Ports 2 and 3 are not functional in the ICH9 Base and Mobile components. See Section 1.3 for details on component feature availability. AHCI The ICH9 provides hardware support for Advanced Host Controller Interface (AHCI), a new programming interface for SATA host controllers. Platforms supporting AHCI may take advantage of performance features such as no master/slave designation for SATA devices—each device is treated as a master—and hardware-assisted native command queuing. AHCI also provides usability enhancements such as Hot-Plug. AHCI requires appropriate software support (e.g., an AHCI driver) and for some features, hardware support in the SATA device or additional platform hardware. See Section 1.3 for details on component feature availability. Intel® Matrix Storage Technology (Intel® ICH9R, ICH9DH, ICH9DO, ICH9M, and ICH9M-E Only) The ICH9 provides support for Intel® Matrix Storage Technology, providing both AHCI (see above for details on AHCI) and integrated RAID functionality. The industry-leading RAID capability provides high-performance RAID 0, 1, 5, and 10 functionality on up to Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 49 Introduction 6 SATA ports of ICH9. Matrix RAID support is provided to allow multiple RAID levels to be combined on a single set of hard drives, such as RAID 0 and RAID 1 on two disks. Other RAID features include hot spare support, SMART alerting, and RAID 0 auto replace. Software components include an Option ROM for pre-boot configuration and boot functionality, a Microsoft Windows* compatible driver, and a user interface for configuration and management of the RAID capability of ICH9. Please see Section 1.3 for details on component feature availability. Note: Intel® Matrix Storage Technology RAID functionality not supported on ICH9M base component. PCI Interface The ICH9 PCI interface provides a 33 MHz, Revision 2.3 implementation. The ICH9 integrates a PCI arbiter that supports up to four external PCI bus masters in addition to the internal ICH9 requests. This allows for combinations of up to four PCI down devices and PCI slots. Low Pin Count (LPC) Interface The ICH9 implements an LPC Interface as described in the LPC 1.1 Specification. The Low Pin Count (LPC) bridge function of the ICH9 resides in PCI Device 31:Function 0. In addition to the LPC bridge interface function, D31:F0 contains other functional units including DMA, interrupt controllers, timers, power management, system management, GPIO, and RTC. Serial Peripheral Interface (SPI) The ICH9 implements an SPI Interface as an alternative interface for the BIOS flash device. An SPI flash device can be used as a replacement for the FWH, and is required to support Gigabit Ethernet, Intel® Active Management Technology (Intel® ICH9DO and ICH9M-E only), and integrated Intel® Quiet System Technology (Desktop Only). The ICH9 supports up to two SPI flash devices with speed up to 33 MHz using two chip select pins. Compatibility Modules (DMA Controller, Timer/Counters, Interrupt Controller) The DMA controller incorporates the logic of two 82C37 DMA controllers, with seven independently programmable channels. Channels 0–3 are hardwired to 8-bit, count-bybyte transfers, and channels 5–7 are hardwired to 16-bit, count-by-word transfers. Any two of the seven DMA channels can be programmed to support fast Type-F transfers. Channel 4 is reserved as a generic bus master request. The ICH9 supports LPC DMA, which is similar to ISA DMA, through the ICH9’s DMA controller. LPC DMA is handled through the use of the LDRQ# lines from peripherals and special encoding on LAD[3:0] from the host. Single, Demand, Verify, and Increment modes are supported on the LPC interface. The timer/counter block contains three counters that are equivalent in function to those found in one 82C54 programmable interval timer. These three counters are combined to provide the system timer function, and speaker tone. The 14.31818 MHz oscillator input provides the clock source for these three counters. The ICH9 provides an ISA-Compatible Programmable Interrupt Controller (PIC) that incorporates the functionality of two, 82C59 interrupt controllers. The two interrupt controllers are cascaded so that 14 external and two internal interrupts are possible. In addition, the ICH9 supports a serial interrupt scheme. 50 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction All of the registers in these modules can be read and restored. This is required to save and restore system state after power has been removed and restored to the platform. Advanced Programmable Interrupt Controller (APIC) In addition to the standard ISA compatible Programmable Interrupt controller (PIC) described in the previous section, the ICH9 incorporates the Advanced Programmable Interrupt Controller (APIC). Universal Serial Bus (USB) Controllers The ICH9 contains up to two Enhanced Host Controller Interface (EHCI) host controllers that support USB high-speed signaling. High-speed USB 2.0 allows data transfers up to 480 Mb/s which is 40 times faster than full-speed USB. The ICH9 also contains up to six Universal Host Controller Interface (UHCI) controllers that support USB full-speed and low-speed signaling. The ICH9 supports up to twelve USB 2.0 ports. All twelve ports are high-speed, fullspeed, and low-speed capable. ICH9’s port-routing logic determines whether a USB port is controlled by one of the UHCI or EHCI controllers. See Section 5.18 and Section 5.19 for details. Gigabit Ethernet Controller The Gigabit Ethernet Controller provides a system interface via a PCI function. The controller provides a full memory-mapped or IO mapped interface along with a 64 bit address master support for systems using more than 4 GB of physical memory and DMA (Direct Memory Addressing) mechanisms for high performance data transfers. Its bus master capabilities enable the component to process high-level commands and perform multiple operations; this lowers processor utilization by off-loading communication tasks from the processor. Two large configurable transmit and receive FIFOs (up to 20 KB each) help prevent data underruns and overruns while waiting for bus accesses. This enables the integrated LAN controller to transmit data with minimum interframe spacing (IFS). The LAN controller can operate at multiple speeds (10/100/1000 MB/s) and in either full duplex or half duplex mode. In full duplex mode the LAN controller adheres with the IEEE 802.3x Flow Control Specification. Half duplex performance is enhanced by a proprietary collision reduction mechanism. See Section 5.3 for details. RTC The ICH9 contains a Motorola MC146818A-compatible real-time clock with 256 bytes of battery-backed RAM. The real-time clock performs two key functions: keeping track of the time of day and storing system data, even when the system is powered down. The RTC operates on a 32.768 KHz crystal and a 3 V battery. The RTC also supports two lockable memory ranges. By setting bits in the configuration space, two 8-byte ranges can be locked to read and write accesses. This prevents unauthorized reading of passwords or other system security information. The RTC also supports a date alarm that allows for scheduling a wake up event up to 30 days in advance, rather than just 24 hours in advance. GPIO Various general purpose inputs and outputs are provided for custom system design. The number of inputs and outputs varies depending on ICH9 configuration. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 51 Introduction Enhanced Power Management The ICH9’s power management functions include enhanced clock control and various low-power (suspend) states (e.g., Suspend-to-RAM and Suspend-to-Disk). A hardwarebased thermal management circuit permits software-independent entrance to lowpower states. The ICH9 contains full support for the Advanced Configuration and Power Interface (ACPI) Specification, Revision 3.0a. Intel® Active Management Technology (Intel® AMT) (Digital Office Only) Intel® Active Management Technology is the next generation of client manageability via the wired network. Intel AMT is a set of advanced manageability features developed as a direct result of IT customer feedback gained through Intel market research. With the new implementation of System Defense in ICH9, the advanced manageability feature set of Intel AMT is further enhanced. Please see Section 1.3 for details on component feature availability. Manageability The ICH9 integrates several functions designed to manage the system and lower the total cost of ownership (TCO) of the system. These system management functions are designed to report errors, diagnose the system, and recover from system lockups without the aid of an external microcontroller. • TCO Timer. The ICH9’s integrated programmable TCO timer is used to detect system locks. The first expiration of the timer generates an SMI# that the system can use to recover from a software lock. The second expiration of the timer causes a system reset to recover from a hardware lock. • Processor Present Indicator. The ICH9 looks for the processor to fetch the first instruction after reset. If the processor does not fetch the first instruction, the ICH9 will reboot the system. • ECC Error Reporting. When detecting an ECC error, the host controller has the ability to send one of several messages to the ICH9. The host controller can instruct the ICH9 to generate either an SMI#, NMI, SERR#, or TCO interrupt. • Function Disable. The ICH9 provides the ability to disable the following integrated functions: LAN, USB, LPC, Intel HD Audio, SATA, PCI Express or SMBus. Once disabled, these functions no longer decode I/O, memory, or PCI configuration space. Also, no interrupts or power management events are generated from the disabled functions. • Intruder Detect. The ICH9 provides an input signal (INTRUDER#) that can be attached to a switch that is activated by the system case being opened. The ICH9 can be programmed to generate an SMI# or TCO interrupt due to an active INTRUDER# signal. System Management Bus (SMBus 2.0) The ICH9 contains an SMBus Host interface that allows the processor to communicate with SMBus slaves. This interface is compatible with most I2C devices. Special I2C commands are implemented. The ICH9’s SMBus host controller provides a mechanism for the processor to initiate communications with SMBus peripherals (slaves). Also, the ICH9 supports slave functionality, including the Host Notify protocol. Hence, the host controller supports eight command protocols of the SMBus interface (see System Management Bus (SMBus) Specification, Version 2.0): Quick Command, Send Byte, Receive Byte, Write Byte/Word, Read Byte/Word, Process Call, Block Read/Write, and Host Notify. 52 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Introduction ICH9’s SMBus also implements hardware-based Packet Error Checking for data robustness and the Address Resolution Protocol (ARP) to dynamically provide address to all SMBus devices. Intel® High Definition Audio Controller The Intel® High Definition Audio Specification defines a digital interface that can be used to attach different types of codecs, such as audio and modem codecs. The ICH9 Intel® HD Audio controller supports up to 4 codecs. The link can operate at either 3.3 V or 1.5 V. With the support of multi-channel audio stream, 32-bit sample depth, and sample rate up to 192 kHz, the Intel® HD Audio controller provides audio quality that can deliver CE levels of audio experience. On the input side, the ICH9 adds support for an array of microphones. Intel® Quiet System Technology (Intel® QST) (Desktop Only) The ICH9 integrates four fan speed sensors (four TACH signals) and 3 fan speed controllers (three Pulse Width Modulator signals), which enables monitoring and controlling up to four fans on the system. With the new implementation of the singlewire Simple Serial Transport (SST) 1.0 bus and Platform Environmental Control Interface (PECI), the ICH9 provides an easy way to connect to SST-based thermal sensors and access the processor thermal data. In addition, coupled with the new sophisticated fan speed control algorithms, Intel® QST provides effective thermal and acoustic management for the platform. Note: Intel® Quiet System Technology functionality requires a correctly configured system, including an appropriate (G)MCH with ME, ME firmware, and system BIOS support. Intel® Virtualization Technology for Directed I/O (Intel® VT-d) The ICH9 provides hardware support for implementation of Intel® Virtualization Technology with Directed I/O (Intel® VT-d). Intel VT-d Technology consists of technology components that support the virtualization of platforms based on Intel® Architecture Processors. Intel VT-d Technology enables multiple operating systems and applications to run in independent partitions. A partition behaves like a virtual machine (VM) and provides isolation and protection across partitions. Each partition is allocated it’s own subset of host physical memory. Integrated Trusted Platform Module (Mobile Only) The integrated Trusted Platform Module (TPM) implementation consists of firmware, Intel® Management Engine resources and dedicated hardware within the ICH and the (G)MCH. The integrated TPM supports all requirements of the TPM Specification Version 1.2, Revision 103, as published by the Trusted Computing Group. The Integrated TPM behaves like a discrete TPM device, and can support third party applications, as well as Microsoft* specific functionality in the Vista* OS. Note: Integrated TPM functionality requires a correctly configured system, including an appropriate mobile (G)MCH with Intel Management Engine firmware, ICH9M and SPI Flash. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 53 Introduction 1.3 Intel® ICH9 Family High-Level Component Differences Table 1-4. Intel® ICH9 Desktop/Server Family Short Name SATA Ports (#) ICH9 Base ICH9 ICH9 RAID Component Name Intel® Matrix Storage Technology Intel® ViivTM Platform Driver Support AHCI RAID 0/1/5/10 Support 4 (Note 3) No (Note 4) No No ICH9R 6 Yes Yes Yes ICH9 Digital Home ICH9DH 6 Yes No Yes ICH9 Digital Office ICH9DO 6 Yes Yes No NOTES: 1. Contact your local Intel Field Sales Representative for currently available ICH9 components. 2. Table above shows feature difference between ICH9 components. If a feature is not listed in the table it is considered a Base feature that is included in all components. 3. SATA ports 2 and 3 are not functional in the base component. 4. ICH9 Base provides hardware support for AHCI functionality when enabled by appropriate system configuration and software driver. Table 1-5. Intel® ICH9 Mobile Family Component Name Intel® Matrix Storage Technology Short Name AHCI RAID 0/1/5/10 Support Intel® Active Management Technology ICH9 Mobile Base ICH9M Yes No No ICH9 Mobile Enhanced ICH9M-E Yes Yes Yes NOTES: 1. Contact your local Intel Field Sales Representative for currently available ICH9 components. 2. Table above shows feature difference between ICH9 mobile components. If a feature is not listed in the table it is considered a Base feature that is included in all mobile components. §§ 54 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2 Signal Description This chapter provides a detailed description of each signal. The signals are arranged in functional groups according to their associated interface. The “#” symbol at the end of the signal name indicates that the active, or asserted state occurs when the signal is at a low voltage level. When “#” is not present, the signal is asserted when at the high voltage level. The following notations are used to describe the signal type: I Input Pin O Output Pin OD O Open Drain Output Pin. I/OD Bi-directional Input/Open Drain Output Pin. I/O Bi-directional Input / Output Pin. The “Type” for each signal is indicative of the functional operating mode of the signal. Unless otherwise noted in Section 3.2 or Section 3.3, a signal is considered to be in the functional operating mode after RTCRST# deasserts for signals in the RTC well, after RSMRST# deasserts for signals in the suspend well, after PWROK asserts for signals in the core well, and after LAN_RST# deasserts for signals in the LAN well. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 55 Signal Description Figure 2-1. Intel® ICH9 Interface Signals Block Diagram (Desktop) AD[31:0] C/BE[3:0]# DEVSEL# FRAME# IRDY# TRDY# STOP# PAR PERR# REQ0# REQ1# / GPIO50 REQ2# / GPIO52 REQ3# / GPIO54 GNT0# GNT1# / GPIO51 GNT2# / GPIO53 GNT3# / GPIO55 SERR# PME# PCICLK PCIRST# PLOCK# A20M# FERR# IGNNE# INIT# INIT3_3V# INTR NMI SMI# STPCLK# RCIN# A20GATE CPUPWRGD Gigabit LAN Connect Interface Controller Link PCI Interface PCI Express* Interface Serial ATA Interface SERIRQ PIRQ[D:A]# PIRQ[H:E]# / GPIO[5:2] USB RTCX1 RTCX2 RTC CLK14 CLK48 SATA_CLKP, SATA_CLKN DMI_CLKP, DMI_CLKN DMI[3:0]TXP, DMI[3:0]TXN DMI[3:0]RXP, DMI[3:0]RXN DMI_ZCOMP DMI_IRCOMP INTVRMEN SPKR SRTCRST#; RTCRST# TP[5:4] TP[7,2:1] TP[6,0] LAN100_SLP Misc. Signals GPIO[49,34:32,28:27, 20,18,16,13:12,8,0] General Purpose I/O PWM[2:0] TACH0/GPIO17; TACH1/GPIO1 TACH2/GPIO6; TACH3/GPIO7 SST PECI 56 Firmware Hub Clocks SATA[5:0]TXP, SATA[5:0]TXN SATA[5:0]RXP, SATA[5:0]RXN SATARBIAS SATARBIAS# SATALED# SATACLKREQ# / GPIO35 SATA0GP /GPIO21 SATA1GP /GPIO19 SATA2GP /GPIO36 SATA3GP /GPIO37 SATA4GP SATA5GP SCLOCK/GPIO22 SLOAD/GPIO38 SDATAOUT0/GPIO39 SDATAOUT1/GPIO48 Direct Media Interface SPI USB[11:0]P; USB[11:0]N OC0#/GPIO59; OC1#/GPIO40 OC2#/GPIO41; OC3#/GPIO42 OC4#/GPIO43; OC5#/GPIO29 OC6#/GPIO30; OC7#/GPIO31 OC8#/GPIO44; OC9#/GPIO45 OC10#/GPIO46; OC11#/GPIO47 USBRBIAS USBRBIAS# PETp[5:1], PETn[5:1] PERp[5:1], PERn[5:1] GLAN_TXp/PET6p; GLAN_TXn/PET6n GLAN_RXp/PER6p; GLAN_RXn/PER6n Intel® High Definition Audio Processor Interface Interrupt Interface CL_CLK0 ; CL_DATA0 CL_VREF0 CL_RST0# THRM# THRMTRIP# SYS_RESET# RSMRST# MCH_SYNC# SLP_S3# SLP_S4# SLP_S5# SLP_M# S4_STATE#/GPIO26 PWROK CLPWROK PWRBTN# RI# WAKE# SUS_STAT# / LPCPD# SUSCLK LAN_RST# VRMPWRGD PLTRST# CK_PWRGD STP_PCI# / GPIO15 STP_CPU# / GPIO25 HDA_RST# HDA_SYNC HDA_BIT_CLK HDA_SDOUT HDA_SDIN[3:0] Power Mgnt. SPI_CS0# SPI_CS1#/CLGPIO6/GPIO58 SPI_MISO SPI_MOSI SPI_CLK LAN_RSTSYNC GLAN_CLK GLAN_TXp/PET6p; GLAN_TXn/PET6n GLAN_RXp/PER6p; GLAN_RXn/PER6n GLAN_COMPO GLAN_COMPI FWH[3:0] / LAD[3:0] FWH4 / LFRAME# LPC Interface LAD[3:0] / FWH[3:0] LFRAME# / FWH4 LDRQ0# LDRQ1# / GPIO23 SMBus Interface SMBDATA SMBCLK SMBALERT# / GPIO11 System Mgnt. INTRUDER# SMLINK[1:0] LINKALERT#/CLGPIO4/GPIO60 MEM_LED/GPIO24; CLGPIO1/GPIO10 CLGPIO2/GPIO14; CLGPIO5/GPIO57 GLGPIO6/SPI_CS1#/GPIO58; WOL_EN/GPIO9 LAN Connect Interface GLAN_CLK LAN_RXD[2:0] LAN_TXD[2:0] LAN_RSTSYNC Fan Speed Control Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Figure 2-2. Intel® ICH9 Interface Signals Block Diagram (Mobile) AD[31:0] C/BE[3:0]# DEVSEL# FRAME# IRDY# TRDY# STOP# PAR PERR# REQ0# REQ1# / GPIO50 REQ2# / GPIO52 REQ3# / GPIO54 GNT0# GNT1# / GPIO51 GNT2# / GPIO53 GNT3# / GPIO55 SERR# PME# PCICLK PCIRST# PLOCK# A20M# FERR# IGNNE# INIT# INTR NMI SMI# STPCLK# RCIN# A20GATE CPUPWRGD DPSLP# SPI_CS0# SPI_CS1#/GPIO58/CLGPIO6 SPI_MISO SPI_MOSI SPI_CLK SERIRQ PIRQ[D:A]# PIRQ[H:E]# / GPIO[5:2] GbE Controller Controller Link PCI Interface Serial Serial ATA ATA Interface Interface Processor Interface Power Mgnt. SPI Interrupt Interface USB[11:0]P; USB[11:0]N OC0#/GPIO59; OC1#/GPIO40 OC2#/GPIO41; OC3#/GPIO42 OC4#/GPIO43; OC5#/GPIO29 OC6#/GPIO30; OC7#/GPIO31 OC8#/GPIO44; OC9#/GPIO45 OC10#/GPIO46; OC11#/GPIO47 USBRBIAS USBRBIAS# USB RTCX1 RTCX2 CLK14 CLK48 SATA_CLKP, SATA_CLKN DMI_CLKP, DMI_CLKN INTVRMEN SPKR RTCRST#; SRTCRST# TP[12:8,3] LAN100_SLP GPIO[56,49,28:27,20,18:17, 13, 8:6,1] GLAN_CLK LAN_RXD[2:0] LAN_TXD[2:0] LAN_RSTSYNC LAN_PHY_PWR_CTRL/GPIO12 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI Express* Interface GLAN_CLK GLAN_TXp/PET6p; GLAN_TXn/PET6n GLAN_RXp/PER6p; GLAN_RXn/PER6n GLAN_COMPO GLAN_COMPI CL_CLK[1:0] ; CL_DATA[1:0] CL_VREF[1:0] CL_RST[1:0]# PETp[5:1], PETn[5:1] PERp[5:1], PERn[5:1] GLAN_TXp/PET6p; GLAN_TXn/PET6n GLAN_RXp/PER6p; GLAN_RXn/PER6n SATA[5:4,1:0]TXP, SATA[5:4,1:0]TXN SATA[5:4,1:0]RXP, SATA[5:4,1:0]RXN SATARBIAS SATARBIAS# SATALED# SATACLKREQ# / GPIO35 SATA0GP /GPIO21; SATA1GP /GPIO19 SATA4GP /GPIO36; SATA5GP /GPIO37 SCLOCK/GPIO22 SLOAD/GPIO38 SDATAOUT0/GPIO39 SDATAOUT1/GPIO48 THRM# THRMTRIP# SYS_RESET# RSMRST# MCH_SYNC# SLP_S3# SLP_S4# SLP_S5# SLP_M# S4_STATE#/GPIO26 PWROK CLPWROK PWRBTN# RI# WAKE# SUS_STAT# / LPCPD SUSCLK LAN_RST# VRMPWRGD PLTRST# CK_PWRGD PMSYNC#/GPIO0 CLKRUN# STP_PCI# STP_CPU# BATLOW# DPRSLPVR/GPIO16 DPRSTP# Intel® High Definition Audio HDA_RST# HDA_SYNC HDA_BIT_CLK HDA_SDOUT HDA_SDIN[3:0] HDA_DOCK_EN/GPIO33 HDA_DOCK_RST#/GPIO34 RTC Direct Media Interface DMI[3:0]TXP, DMI[3:0]TXN DMI[3:0]RXP, DMI[3:0]RXN DMI_ZCOMP DMI_IRCOMP Clocks Firmware Hub FWH[3:0] / LAD[3:0] FWH4 / LFRAME# Misc. Signals General Purpose I/O Platform LAN Connect LPC Interface LAD[3:0] / FWH[3:0] LFRAME# / FWH4 LDRQ0# LDRQ1# / GPIO23 SMBus Interface SMBDATA SMBCLK SMBALERT# / GPIO11 System Mgnt. INTRUDER# SMLINK[1:0] LINKALERT#/CLGPIO4/GPIO60 MEM_LED/GPIO24; SUS_PWR_ACK/ GPIO10; AC_PRESENT/GPIO14; WOL_EN/GPIO9; CLGPIO5/GPIO57 57 Signal Description 2.1 Direct Media Interface (DMI) to Host Controller Table 2-1. Direct Media Interface Signals Name 58 Type Description DMI0TXP, DMI0TXN O Direct Media Interface Differential Transmit Pair 0 DMI0RXP, DMI0RXN I Direct Media Interface Differential Receive Pair 0 DMI1TXP, DMI1TXN O Direct Media Interface Differential Transmit Pair 1 DMI1RXP, DMI1RXN I Direct Media Interface Differential Receive Pair 1 DMI2TXP, DMI2TXN O Direct Media Interface Differential Transmit Pair 2 DMI2RXP, DMI2RXN I Direct Media Interface Differential Receive Pair 2 DMI3TXP, DMI3TXN O Direct Media Interface Differential Transmit Pair 3 DMI3RXP, DMI3RXN I Direct Media Interface Differential Receive Pair 3 DMI_ZCOMP I Impedance Compensation Input: Determines DMI input impedance. DMI_IRCOMP O Impedance/Current Compensation Output: Determines DMI output impedance and bias current. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2.2 PCI Express* Table 2-2. PCI Express* Signals Name Type Description PETp1, PETn1 O PCI Express* Differential Transmit Pair 1 PERp1, PERn1 I PCI Express Differential Receive Pair 1 PETp2, PETn2 O PCI Express Differential Transmit Pair 2 PERp2, PERn2 I PCI Express Differential Receive Pair 2 PETp3, PETn3 O PCI Express Differential Transmit Pair 3 PERp3, PERn3 I PCI Express Differential Receive Pair 3 PETp4, PETn4 O PCI Express Differential Transmit Pair 4 PERp4, PERn4 I PCI Express Differential Receive Pair 4 PETp5, PETn5 O PCI Express Differential Transmit Pair 5 PERp5, PERn5 I PCI Express Differential Receive Pair 5 PETp6/GLAN_TXp, PETn6/GLAN_TXn O PCI Express Differential Transmit Pair 6: The differential pair will function as the Gigabit LAN Connect Interface transmit pair when the integrated Gigabit LAN controller is enabled. PERp6/GLAN_RXp, PERn6/GLAN_RXn I PCI Express Differential Receive Pair 6: The differential pair will function as the Gigabit LAN Connect Interface receive pair when the integrated Gigabit LAN controller is enabled. 2.3 LAN Connect Interface Table 2-3. LAN Connect Interface Signals Name Type Description Gigabit LAN Input Clock: Clock driven by the Platform LAN Connect device. The frequency will vary depending on link speed. GLAN_CLK I NOTE: The clock is shared between the LAN Connect Interface and the Gigabit LAN Connect Interface. LAN_RXD[2:0] I Received Data: The Platform LAN Connect device uses these signals to transfer data and control information to the integrated LAN controller. These signals have integrated weak pull-up resistors. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 59 Signal Description Table 2-3. LAN Connect Interface Signals Name Type LAN_TXD[2:0] O LAN_RSTSYNC O Description Transmit Data: The integrated LAN controller uses these signals to transfer data and control information to the Platform LAN Connect component. LAN Reset/Sync: This is the reset/sync signal from the LAN Connect Interface to the physical device. The Platform LAN Connect device’s Reset and Sync signals are multiplexed onto this pin. NOTE: The signal is shared between LAN Connect Interface and Gigabit LAN Connect Interface. LAN_PHY_PW R_CTRL (Mobile Only) / GPIO12 O LAN PHY Power Control: This signal may optionally be connected to a switch to turn 3.3V PHY power off when LAN is disabled for additional power savings. This capability is configured in the NVM. When using an 82567 PHY solution, the LAN_PHY_PWR_CTRL signal should be connected to the PHY’s LAN_DISABLE_N pin for a hardware based LAN disable mechanism. Signal can instead be used as GPIO12. 2.4 Gigabit LAN Connect Interface Table 2-4. Gigabit LAN Connect Interface Signals Name GLAN_CLK Type I Description Gigabit LAN Input Clock: Clock driven by the Platform LAN Connect device. The frequency will vary depending on link speed. NOTE: The clock is shared between the LAN Connect Interface and the Gigabit LAN Connect Interface. O Gigabit LAN Differential Transmit Pair. Can be instead used as PCI Express port 6 differential transmit pair. I Gigabit LAN Differential Receive Pair. Can be instead used as PCI Express port 6 differential receive pair. GLAN_COMPO O Impedance Compensation Output pad: Determines Gigabit LAN Connect Interface output impedance and bias current. GLAN_COMPI I Impedance Compensation Input pad: Determines Gigabit LAN Connect Interface input impedance. GLAN_TXp/PET6p; GLAN_TXn/PET6n GLAN_RXp/PER6p; GLAN_RXn/PER6n LAN_RSTSYNC O LAN Reset/Sync: This is the reset/sync signal from the Gigabit LAN interface to the physical device. The Platform LAN Connect device’s Reset and Sync signals are multiplexed onto this pin. NOTE: The signal is shared between LAN Connect Interface and Gigabit LAN Connect Interface. 60 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2.5 Firmware Hub Interface Table 2-5. Firmware Hub Interface Signals Name Type FWH[3:0] / LAD[3:0] I/O FWH4 / LFRAME# O Firmware Hub Signals. This signal is multiplexed with the LPC LFRAME# signal. O Initialization 3.3 V: This is the identical 3.3 V copy of INIT# intended for Firmware Hub. INIT3_3V# (Desktop Only) Description Firmware Hub Signals. These signals are multiplexed with the LPC address signals. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 61 Signal Description 2.6 PCI Interface Table 2-6. PCI Interface Signals (Sheet 1 of 3) Name AD[31:0] Type I/O Description PCI Address/Data: AD[31:0] is a multiplexed address and data bus. During the first clock of a transaction, AD[31:0] contain a physical address (32 bits). During subsequent clocks, AD[31:0] contain data. The Intel® ICH9 will drive all 0s on AD[31:0] during the address phase of all PCI Special Cycles. Bus Command and Byte Enables: The command and byte enable signals are multiplexed on the same PCI pins. During the address phase of a transaction, C/BE[3:0]# define the bus command. During the data phase C/ BE[3:0]# define the Byte Enables. C/BE[3:0]# 0000b C/BE[3:0]# I/O Command Type Interrupt Acknowledge 0001b Special Cycle 0010b I/O Read 0011b I/O Write 0110b Memory Read 0111b Memory Write 1010b Configuration Read 1011b Configuration Write 1100b Memory Read Multiple 1110b Memory Read Line 1111b Memory Write and Invalidate All command encodings not shown are reserved. The ICH9 does not decode reserved values, and therefore will not respond if a PCI master generates a cycle using one of the reserved values. DEVSEL# FRAME# 62 I/O Device Select: The ICH9 asserts DEVSEL# to claim a PCI transaction. As an output, the ICH9 asserts DEVSEL# when a PCI master peripheral attempts an access to an internal ICH9 address or an address destined for DMI (main memory or graphics). As an input, DEVSEL# indicates the response to an ICH9-initiated transaction on the PCI bus. DEVSEL# is tri-stated from the leading edge of PLTRST#. DEVSEL# remains tri-stated by the ICH9 until driven by a target device. I/O Cycle Frame: The current initiator drives FRAME# to indicate the beginning and duration of a PCI transaction. While the initiator asserts FRAME#, data transfers continue. When the initiator negates FRAME#, the transaction is in the final data phase. FRAME# is an input to the ICH9 when the ICH9 is the target, and FRAME# is an output from the ICH9 when the ICH9 is the initiator. FRAME# remains tri-stated by the ICH9 until driven by an initiator. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-6. PCI Interface Signals (Sheet 2 of 3) Name IRDY# TRDY# STOP# PAR PERR# Type Description I/O Initiator Ready: IRDY# indicates the ICH9's ability, as an initiator, to complete the current data phase of the transaction. It is used in conjunction with TRDY#. A data phase is completed on any clock both IRDY# and TRDY# are sampled asserted. During a write, IRDY# indicates the ICH9 has valid data present on AD[31:0]. During a read, it indicates the ICH9 is prepared to latch data. IRDY# is an input to the ICH9 when the ICH9 is the target and an output from the ICH9 when the ICH9 is an initiator. IRDY# remains tri-stated by the ICH9 until driven by an initiator. I/O Target Ready: TRDY# indicates the ICH9's ability as a target to complete the current data phase of the transaction. TRDY# is used in conjunction with IRDY#. A data phase is completed when both TRDY# and IRDY# are sampled asserted. During a read, TRDY# indicates that the ICH9, as a target, has placed valid data on AD[31:0]. During a write, TRDY# indicates the ICH9, as a target is prepared to latch data. TRDY# is an input to the ICH9 when the ICH9 is the initiator and an output from the ICH9 when the ICH9 is a target. TRDY# is tri-stated from the leading edge of PLTRST#. TRDY# remains tri-stated by the ICH9 until driven by a target. I/O Stop: STOP# indicates that the ICH9, as a target, is requesting the initiator to stop the current transaction. STOP# causes the ICH9, as an initiator, to stop the current transaction. STOP# is an output when the ICH9 is a target and an input when the ICH9 is an initiator. I/O Calculated/Checked Parity: PAR uses “even” parity calculated on 36 bits, AD[31:0] plus C/BE[3:0]#. “Even” parity means that the ICH9 counts the number of ones within the 36 bits plus PAR and the sum is always even. The ICH9 always calculates PAR on 36 bits regardless of the valid byte enables. The ICH9 generates PAR for address and data phases and only ensures PAR to be valid one PCI clock after the corresponding address or data phase. The ICH9 drives and tri-states PAR identically to the AD[31:0] lines except that the ICH9 delays PAR by exactly one PCI clock. PAR is an output during the address phase (delayed one clock) for all ICH9 initiated transactions. PAR is an output during the data phase (delayed one clock) when the ICH9 is the initiator of a PCI write transaction, and when it is the target of a read transaction. ICH9 checks parity when it is the target of a PCI write transaction. If a parity error is detected, the ICH9 will set the appropriate internal status bits, and has the option to generate an NMI# or SMI#. I/O Parity Error: An external PCI device drives PERR# when it receives data that has a parity error. The ICH9 drives PERR# when it detects a parity error. The ICH9 can either generate an NMI# or SMI# upon detecting a parity error (either detected internally or reported via the PERR# signal). REQ0# REQ1#/ GPIO50 REQ2#/ GPIO52 I PCI Requests: The ICH9 supports up to 4 masters on the PCI bus. REQ[3:1]# pins can instead be used as GPIO. REQ3#/ GPIO54 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 63 Signal Description Table 2-6. PCI Interface Signals (Sheet 3 of 3) Name Type Description PCI Grants: The ICH9 supports up to 4 masters on the PCI bus. GNT[3:1]# pins can instead be used as GPIO. GNT0# GNT1#/ GPIO51 GNT2#/ GPIO53 O GNT3#/ GPIO55 PCICLK PCIRST# PLOCK# Pull-up resistors are not required on these signals. If pull-ups are used, they should be tied to the Vcc3_3 power rail. NOTE: GNT[3:0]# are sampled as a functional strap. See Section 2.24.1 for details. I O I/O PCI Clock: This is a 33 MHz clock. PCICLK provides timing for all transactions on the PCI Bus. Note: (Mobile Only) This clock does not stop based on STP_PCI# signal. PCI Clock only stops based on SLP_S3#. PCI Reset: This is the Secondary PCI Bus reset signal. It is a logical OR of the primary interface PLTRST# signal and the state of the Secondary Bus Reset bit of the Bridge Control register (D30:F0:3Eh, bit 6). PCI Lock: This signal indicates an exclusive bus operation and may require multiple transactions to complete. ICH9 asserts PLOCK# when it performs non-exclusive transactions on the PCI bus. PLOCK# is ignored when PCI masters are granted the bus in desktop configurations. Note: In mobile configuration, devices on the PCI bus (other than the ICH9) are not permitted to assert the PLOCK# signal. SERR# PME# I/OD System Error: SERR# can be pulsed active by any PCI device that detects a system error condition. Upon sampling SERR# active, the ICH9 has the ability to generate an NMI, SMI#, or interrupt. I/OD PCI Power Management Event: PCI peripherals drive PME# to wake the system from low-power states S1–S5. PME# assertion can also be enabled to generate an SCI from the S0 state. In some cases the ICH9 may drive PME# active due to an internal wake event. The ICH9 will not drive PME# high, but it will be pulled up to VccSus3_3 by an internal pull-up resistor. 2.7 Serial ATA Interface Table 2-7. Serial ATA Interface Signals (Sheet 1 of 4) Name SATA0TXP SATA0TXN SATA0RXP SATA0RXN SATA1TXP SATA1TXN 64 Type O I O Description Serial ATA 0 Differential Transmit Pairs: These are outbound high-speed differential signals to Port 0. In compatible mode, SATA Port 0 is the primary master of SATA Controller 1. Serial ATA 0 Differential Receive Pair: These are inbound highspeed differential signals from Port 0. In compatible mode, SATA Port 0 is the primary master of SATA Controller 1. Serial ATA 1 Differential Transmit Pair: These are outbound high-speed differential signals to Port 1. In compatible mode, SATA Port 1 is the secondary master of SATA Controller 1. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-7. Serial ATA Interface Signals (Sheet 2 of 4) Name SATA1RXP SATA1RXN Type I (ICH9R, ICH9DH, ICH9DO Only) O SATA2RXN SATA3TXN I SATA4TXP SATA4TXN SATA4RXP SATA4RXN SATA5TXP SATA5TXN SATA5RXP SATA5RXN In compatible mode, SATA Port 2 is the primary slave of SATA Controller 1. NOTE: This port is not functional in the Desktop ICH9 Base component. Serial ATA 3 Differential Transmit Pair: These are outbound high-speed differential signals to Port 3. O In compatible mode, SATA Port 3 is the secondary slave of SATA Controller 1. NOTE: This port is not functional in the Desktop ICH9 Base component. Serial ATA 3 Differential Receive Pair: These are inbound highspeed differential signals from Port 3. SATA3RXP SATA3RXN (ICH9R, ICH9DH, ICH9DO Only) In compatible mode, SATA Port 2 is the primary slave of SATA Controller 1. Serial ATA 2 Differential Receive Pair: These are inbound highspeed differential signals from Port 2. SATA3TXP (ICH9R, ICH9DH, ICH9DO Only) In compatible mode, SATA Port 1 is the secondary master of SATA Controller 1 NOTE: This port is not functional in the Desktop ICH9 Base component. SATA2RXP (ICH9R, ICH9DH, ICH9DO Only) Serial ATA 1 Differential Receive Pair: These are inbound highspeed differential signals from Port 1. Serial ATA 2 Differential Transmit Pair: These are outbound high-speed differential signals to Port 2. SATA2TXP SATA2TXN Description I O I O I In compatible mode, SATA Port 3 is the secondary slave of SATA Controller 1. NOTE: This port is not functional in the Desktop ICH9 Base component. Serial ATA 4 Differential Transmit Pair: These are outbound high-speed differential signals to Port 4. In compatible mode, SATA Port 4 is the primary master of SATA Controller 2. Serial ATA 4 Differential Receive Pair: These are inbound highspeed differential signals from Port 4. In compatible mode, SATA Port 4 is the primary master of SATA Controller 2 Serial ATA 5 Differential Transmit Pair: These are outbound high-speed differential signals to Port 5. In compatible mode, SATA Port 5 is the secondary master of SATA Controller 2. Serial ATA 5 Differential Receive Pair: These are inbound highspeed differential signals from Port 5. In compatible mode, SATA Port 5 is the secondary master of SATA Controller 2. SATARBIAS O Serial ATA Resistor Bias: This is an analog connection point for an external resistor to ground. SATARBIAS# I Serial ATA Resistor Bias Complement: This is an analog connection point for an external resistor to ground. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 65 Signal Description Table 2-7. Serial ATA Interface Signals (Sheet 3 of 4) Name SATA0GP / GPIO21 Type I Description Serial ATA 0 General Purpose: This is an input pin which can be configured as an interlock switch corresponding to SATA Port 0. When used as an interlock switch status indication, this signal should be drive to ‘0’ to indicate that the switch is closed and to ‘1’ to indicate that the switch is open. If interlock switches are not required, this pin can be configured as GPIO21. SATA1GP / GPIO19 I Serial ATA 1 General Purpose: Same function as SATA0GP, except for SATA Port 1. If interlock switches are not required, this pin can be configured as GPIO19. Serial ATA 2 General Purpose: Same function as SATA0GP, except for SATA Port 2. SATA2GP / GPIO36 (ICH9R, ICH9DH, ICH9DO Only) I If interlock switches are not required, this pin can be configured as GPIO36. NOTE: This signal can also be used as GPIO36 for Desktop components. This signal can only be used as GPIO36 in the Desktop ICH9 Base component. Serial ATA 3 General Purpose: Same function as SATA0GP, except for SATA Port 3. SATA3GP / GPIO37 (ICH9R, ICH9DH, ICH9DO Only) SATA4GP / GPIO36 (Mobile Only) SATA5GP / GPIO37 (Mobile Only) SATALED# I If interlock switches are not required, this pin can be configured as GPIO37. NOTE: This signal can also be used as GPIO37 for Desktop components. This signal can only be used as GPIO37 in the Desktop ICH9 Base component. I I OD O Serial ATA 4 General Purpose: Same function as SATA0GP, except for SATA Port 4. Note: This signal can also be used as GPIO36 for Mobile components. Serial ATA 5 General Purpose: Same function as SATA0GP, except for SATA Port 5. Note: This signal can also be used as GPIO37 for Mobile components. Serial ATA LED: This signal is an open-drain output pin driven during SATA command activity. It is to be connected to external circuitry that can provide the current to drive a platform LED. When active, the LED is on. When tri-stated, the LED is off. An external pull-up resistor to Vcc3_3 is required. NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for details. SATACLKREQ#/ GPIO35 66 OD O Serial ATA Clock Request: This signal is an open-drain output pin when configured as SATACLKREQ#. It is used to connect to the system clock chip. When active, request for SATA Clock running is asserted. When tri-stated, it tells the Clock Chip that SATA Clock can be stopped. An external pull-up resistor is required. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-7. Serial ATA Interface Signals (Sheet 4 of 4) Name Type SCLOCK/GPIO22 OD O Description SGPIO Reference Clock: The SATA controller uses rising edges of this clock to transmit serial data, and the target uses the falling edge of this clock to latch data. If SGPIO interface is not used, this signal can be used as a GPIO. SLOAD/GPIO38 OD O SGPIO Load: The controller drives a ‘1’ at the rising edge of SCLOCK to indicate either the start or end of a bit stream. A 4-bit vendor specific pattern will be transmitted right after the signal assertion. If SGPIO interface is not used, this signal can be used as a GPIO. SDATAOUT0/ GPIO39 OD O SDATAOUT1/ GPIO48 SGPIO Dataout: Driven by the controller to indicate the drive status in the following sequence: drive 0, 1, 2, 3, 4, 5, 0, 1, 2... If SGPIO interface is not used, the signals can be used as GPIO. 2.8 LPC Interface Table 2-8. LPC Interface Signals Name Type LAD[3:0] / FWH[3:0] I/O LPC Multiplexed Command, Address, Data: For LAD[3:0], internal pull-ups are provided. LFRAME# / FWH4 O LPC Frame: LFRAME# indicates the start of an LPC cycle, or an abort. LDRQ0#, LDRQ1# / GPIO23 I Description LPC Serial DMA/Master Request Inputs: LDRQ[1:0]# are used to request DMA or bus master access. These signals are typically connected to an external Super I/O device. An internal pull-up resistor is provided on these signals. LDRQ1# may optionally be used as GPIO. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 67 Signal Description 2.9 Interrupt Interface Table 2-9. Interrupt Signals Name Type SERIRQ I/OD PIRQ[D:A]# PIRQ[H:E]# / GPIO[5:2] 68 I/OD Description Serial Interrupt Request: This pin implements the serial interrupt protocol. PCI Interrupt Requests: In non-APIC mode the PIRQx# signals can be routed to interrupts 3, 4, 5, 6, 7, 9, 10, 11, 12, 14 or 15 as described in Section 5.8.6. Each PIRQx# line has a separate Route Control register. In APIC mode, these signals are connected to the internal I/O APIC in the following fashion: PIRQA# is connected to IRQ16, PIRQB# to IRQ17, PIRQC# to IRQ18, and PIRQD# to IRQ19. This frees the legacy interrupts. PCI Interrupt Requests: In non-APIC mode the PIRQx# signals can be routed to interrupts 3, 4, 5, 6, 7, 9, 10, 11, 12, 14 or 15 as described in Section 5.8.6. Each PIRQx# line has a separate Route Control register. I/OD In APIC mode, these signals are connected to the internal I/O APIC in the following fashion: PIRQE# is connected to IRQ20, PIRQF# to IRQ21, PIRQG# to IRQ22, and PIRQH# to IRQ23. This frees the legacy interrupts. If not needed for interrupts, these signals can be used as GPIO. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2.10 USB Interface Table 2-10. USB Interface Signals Name USBP0P, USBP0N, USBP1P, USBP1N USBP2P, USBP2N, USBP3P, USBP3N USBP4P, USBP4N, USBP5P, USBP5N USBP6P, USBP6N, USBP7P, USBP7N USBP8P, USBP8N, USBP9P, USBP9N Type Description Universal Serial Bus Port [1:0] Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 0 and 1. These ports can be routed to UHCI controller #1 or the EHCI controller #1. I/O NOTE: No external resistors are required on these signals. The Intel® ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. I/O Universal Serial Bus Port [3:2] Differential: These differential pairs are used to transmit data/address/command signals for ports 2 and 3. These ports can be routed to UHCI controller #2 or the EHCI controller #1. NOTE: No external resistors are required on these signals. The ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. I/O Universal Serial Bus Port [5:4] Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 4 and 5. These ports can be routed to UHCI controller #3 or the EHCI controller #1. NOTE: No external resistors are required on these signals. The ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. I/O Universal Serial Bus Port [7:6] Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 6 and 7. These ports can be routed to UHCI controller #4 or the EHCI controller #2. NOTE: No external resistors are required on these signals. The ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. I/O Universal Serial Bus Port [9:8] Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 8 and 9. These ports can be routed to UHCI controller #5 or the EHCI controller #2. NOTE: No external resistors are required on these signals. The ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 69 Signal Description Table 2-10. USB Interface Signals Name USBP10P, USBP10N, USBP11P, USBP11N Type I/O Description Universal Serial Bus Port [11:10] Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 10 and 11. These ports can be routed to UHCI controller #6 or the EHCI controller #2. These ports can be optionally routed to EHCI Controller #1 when bit 0 RCBA 35F0h is set. NOTE: No external resistors are required on these signals. The ICH9 integrates 15 kΩ pull-downs and provides an output driver impedance of 45 Ω which requires no external series resistor. OC0# / GPIO59 Overcurrent Indicators: These signals set corresponding bits in the USB controllers to indicate that an overcurrent condition has occurred. OC1# / GPIO40 OC2# / GPIO41 OC[11:0]# may optionally be used as GPIOs. OC3# / GPIO42 OC4# / GPIO43 OC5# / GPIO29 OC6# / GPIO30 NOTE: OC[11:0]# are not 5 V tolerant. I OC7# / GPIO31 OC8# / GPIO44 OC9# / GPIO45 OC10# / GPIO46 OC11# / GPIO47 70 USBRBIAS O USB Resistor Bias: Analog connection point for an external resistor. Used to set transmit currents and internal load resistors. USBRBIAS# I USB Resistor Bias Complement: Analog connection point for an external resistor. Used to set transmit currents and internal load resistors. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2.11 Power Management Interface Table 2-11. Power Management Interface Signals (Sheet 1 of 3) Name PLTRST# Type O Description Platform Reset: The Intel® ICH9 asserts PLTRST# to reset devices on the platform (e.g., SIO, FWH, LAN, (G)MCH, TPM, etc.). The ICH9 asserts PLTRST# during power-up and when S/W initiates a hard reset sequence through the Reset Control register (I/O Register CF9h). The ICH9 drives PLTRST# inactive a minimum of 1 ms after both PWROK and VRMPWRGD are driven high. The ICH9 drives PLTRST# active a minimum of 1 ms when initiated through the Reset Control register (I/O Register CF9h). NOTE: PLTRST# is in the VccSus3_3 well. I Thermal Alarm: Active low signal generated by external hardware to generate an SMI# or SCI. THRMTRIP# I Thermal Trip: When low, this signal indicates that a thermal trip from the processor occurred, and the ICH9 will immediately transition to a S5 state. The ICH9 will not wait for the processor stop grant cycle since the processor has overheated. SLP_S3# O S3 Sleep Control: SLP_S3# is for power plane control. This signal shuts off power to all non-critical systems when in S3 (Suspend To RAM), S4 (Suspend to Disk), or S5 (Soft Off) states. THRM# S4 Sleep Control: SLP_S4# is for power plane control. This signal shuts power to all non-critical systems when in the S4 (Suspend to Disk) or S5 (Soft Off) state. NOTE: This pin must be used to control the DRAM power in order to use the ICH9’s DRAM power-cycling feature. Refer to Chapter 5.13.11.2 for details. NOTE: In a system with Intel AMT or ASF support, this signal should be used to control the DRAM power. In M1 state (where the host platform is in S3–S5 states and the manageability subsystem is running) the signal is forced high along with SLP_M# in order to properly maintain power to the DIMM used for manageability sub-system. SLP_S4# O SLP_S5# O S5 Sleep Control: SLP_S5# is for power plane control. This signal is used to shut power off to all non-critical systems when in the S5 (Soft Off) states. SLP_M# O Manageability Sleep State Control: This signal is used to control power planes to the Intel® AMT or ASF sub-system. If no Intel AMT or ASF Management Engine firmware is present, SLP_M# will have the same timings as SLP_S3#. O S4 State Indication: This signal asserts low when the host platform is in S4 or S5 state. In platforms where the management engine is forcing the SLP_S4# high along with SLP_M#, this signal can be used by other devices on the board to know when the host platform is below the S3 state. S4_STATE# / GPIO26 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 71 Signal Description Table 2-11. Power Management Interface Signals (Sheet 2 of 3) Name Type Description Power OK: When asserted, PWROK is an indication to the ICH9 that all power rails have been stable for 99 ms and that PCICLK has been stable for 1 ms. PWROK can be driven asynchronously. When PWROK is negated, the ICH9 asserts PLTRST#. PWROK I NOTE: 1. PWROK must deassert for a minimum of three RTC clock periods in order for the ICH9 to fully reset the power and properly generate the PLTRST# output. 2. PWROK must not glitch, even if RSMRST# is low. Controller Link Power OK: When asserted, indicates that power to the Controller Link subsystem (MCH, ICH, etc.) is stable and tells the ICH to deassert CL_RST# to the MCH. CLPWROK I NOTES: 1. CLPWROK must not assert before RSMRST# deasserts. 2. CLPWROK must not assert after PWROK asserts. PWRBTN# I Power Button: The Power Button will cause SMI# or SCI to indicate a system request to go to a sleep state. If the system is already in a sleep state, this signal will cause a wake event. If PWRBTN# is pressed for more than 4 seconds, this will cause an unconditional transition (power button override) to the S5 state. Override will occur even if the system is in the S1-S4 states. This signal has an internal pull-up resistor and has an internal 16 ms de-bounce on the input. RI# I Ring Indicate: This signal is an input from a modem. It can be enabled as a wake event, and this is preserved across power failures. SYS_RESET# I System Reset: This pin forces an internal reset after being debounced. The ICH9 will reset immediately if the SMBus is idle; otherwise, it will wait up to 25 ms ± 2 ms for the SMBus to idle before forcing a reset on the system. I Resume Well Reset: This signal is used for resetting the resume power plane logic. This signal must be asserted for at least 10 ms after the suspend power wells are valid. When deasserted, this signal is an indication that the suspend power wells are stable. RSMRST# LAN Reset: When asserted, the internal LAN controller is in reset. This signal must be asserted until the LAN power wells (VccLAN3_3 and VccLAN1_05) and VccCL3_3 power well are valid. When deasserted, this signal is an indication that the LAN power wells are stable. 72 LAN_RST# I WAKE# I MCH_SYNC# I NOTES: 1. LAN_RST# must not deassert before RSMRST# deasserts 2. LAN_RST# must not deassert after PWROK asserts. 3. LAN_RST# must not deassert until 1ms after the LAN power wells (VccLAN3_3 and VccLAN1_05 and VccCL3_3 power well are valid. 4. If integrated LAN is not used LAN_RST# can be tied to Vss. 5. LAN_RST# must assert a minimum of 20 ns before LAN power rails become inactive. PCI Express* Wake Event: Sideband wake signal on PCI Express asserted by components requesting wake up. MCH SYNC: This input is internally ANDed with the PWROK input. Connect to the ICH_SYNC# output of (G)MCH. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-11. Power Management Interface Signals (Sheet 3 of 3) Name Type Description SUS_STAT# / LPCPD# O Suspend Status: This signal is asserted by the ICH9 to indicate that the system will be entering a low power state soon. This can be monitored by devices with memory that need to switch from normal refresh to suspend refresh mode. It can also be used by other peripherals as an indication that they should isolate their outputs that may be going to powered-off planes. This signal is called LPCPD# on the LPC interface. SUSCLK O Suspend Clock: This clock is an output of the RTC generator circuit to use by other chips for refresh clock. VRMPWRGD I VRM Power Good: This signal should be connected to the processor’s VRM Power Good signifying the VRM is stable. This signal is internally ANDed with the PWROK input. This signal is in the suspend well. CK_PWRGD O PMSYNC# (Mobile Only) / GPIO0 O CLKRUN# (Mobile Only)/ GPIO32 (Desktop Only) I/O STP_PCI# / GPIO15 (Desktop Only) Clock Generator Power Good: indicates to the clock generator when the main power well is valid. This signal is asserted high when both SLP_S3# and VRMPWRGD are high. Power Management Sync: When asserted, it signals the MCH to deassert CPUSLP# pin when exiting out of C5 or C6. Signal may also be used as a GPIO. PCI Clock Run: Used to support PCI CLKRUN protocol. Connects to peripherals that need to request clock restart or prevention of clock stopping. Stop PCI Clock: This signal is an output to the external clock generator for it to turn off the PCI clock. It is used to support PCI CLKRUN# protocol on mobile platforms. O In Sx, this pin is also used to communicate the host clock frequency select for Management Engine operation in order to support Moff/Sx to M1/Sx transitions in a mobile Intel® AMT or ASF enabled system. This signal is used as a GPIO in desktop platforms. STP_CPU# / GPIO25 (Desktop Only) Stop CPU Clock: This signal is an output to the external clock generator for it to turn off the processor clock. It is used to support the C3 state on mobile platforms. O In Sx, this pin is also used to communicate the host clock frequency select for Management Engine operation in order to support Moff/Sx to M1/Sx transitions in a mobile Intel® AMT or ASF enabled system. This signal is used as a GPIO in desktop platforms. I Battery Low: This signal is an input from the battery to indicate that there is insufficient power to boot the system. Assertion will prevent wake from S3–S5 state. This signal can also be enabled to cause an SMI# when asserted. DPRSLPVR (Mobile Only) / GPIO16 O Deeper Sleep - Voltage Regulator: This signal is used to lower the voltage of the VRM during the C4 state. When the signal is high, the voltage regulator outputs the lower “Deeper Sleep” voltage. When low (default), the voltage regulator outputs the higher “Normal” voltage. DPRSTP# (Mobile Only) / TP1 (Desktop Only) O Deeper Stop: This is a copy of the DPRSLPVR and it is active low. BATLOW# (Mobile Only) / TP0 (Desktop Only) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 73 Signal Description 2.12 Processor Interface Table 2-12. Processor Interface Signals (Sheet 1 of 2) Name Type A20M# O FERR# I Description Mask A20: A20M# will go active based on either setting the appropriate bit in the Port 92h register, or based on the A20GATE input being active. Numeric Coprocessor Error: This signal is tied to the coprocessor error signal on the processor. FERR# is only used if the ICH9 coprocessor error reporting function is enabled in the OIC.CEN register (Chipset Config Registers:Offset 31FFh: bit 1). If FERR# is asserted, the ICH9 generates an internal IRQ13 to its interrupt controller unit. It is also used to gate the IGNNE# signal to ensure that IGNNE# is not asserted to the processor unless FERR# is active. FERR# requires an external weak pull-up to ensure a high level when the coprocessor error function is disabled. NOTE: FERR# can be used in some states for notification by the processor of pending interrupt events. This functionality is independent of the OIC register bit setting. IGNNE# O Ignore Numeric Error: This signal is connected to the ignore error pin on the processor. IGNNE# is only used if the ICH9 coprocessor error reporting function is enabled in the OIC.CEN register (Chipset Config Registers:Offset 31FFh: bit 1). If FERR# is active, indicating a coprocessor error, a write to the Coprocessor Error register (I/O register F0h) causes the IGNNE# to be asserted. IGNNE# remains asserted until FERR# is negated. If FERR# is not asserted when the Coprocessor Error register is written, the IGNNE# signal is not asserted. INIT# O Initialization: INIT# is asserted by the ICH9 for 16 PCI clocks to reset the processor. ICH9 can be configured to support processor Built In Self Test (BIST). INTR O CPU Interrupt: INTR is asserted by the ICH9 to signal to the processor that an interrupt request is pending and needs to be serviced. It is an asynchronous output and normally driven low. NMI O Non-Maskable Interrupt: NMI is used to force a non-Maskable interrupt to the processor. The ICH9 can generate an NMI when either SERR# is asserted or IOCHK# goes active via the SERIRQ# stream. The processor detects an NMI when it detects a rising edge on NMI. NMI is reset by setting the corresponding NMI source enable/disable bit in the NMI Status and Control register (I/O Register 61h). SMI# O System Management Interrupt: SMI# is an active low output synchronous to PCICLK. It is asserted by the ICH9 in response to one of many enabled hardware or software events. O Stop Clock Request: STPCLK# is an active low output synchronous to PCICLK. It is asserted by the ICH9 in response to one of many hardware or software events. When the processor samples STPCLK# asserted, it responds by stopping its internal clock. STPCLK# 74 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-12. Processor Interface Signals (Sheet 2 of 2) Name RCIN# Type I Description Keyboard Controller Reset CPU: The keyboard controller can generate INIT# to the processor. This saves the external OR gate with the ICH9’s other sources of INIT#. When the ICH9 detects the assertion of this signal, INIT# is generated for 16 PCI clocks. NOTE: The ICH9 will ignore RCIN# assertion during transitions to the S1, S3, S4, and S5 states. I A20 Gate: A20GATE is from the keyboard controller. The signal acts as an alternative method to force the A20M# signal active. It saves the external OR gate needed with various other chipsets. CPUPWRGD O CPU Power Good: This signal should be connected to the processor’s PWRGOOD input to indicate when the processor power is valid. This is an output signal that represents a logical AND of the ICH9’s PWROK and VRMPWRGD signals. DPSLP# (Mobile Only) / TP2 (Desktop Only) O Deeper Sleep: DPSLP# is asserted by the ICH9 to the processor. When the signal is low, the processor enters the deep sleep state by gating off the processor Core Clock inside the processor. When the signal is high (default), the processor is not in the deep sleep state. A20GATE 2.13 SMBus Interface Table 2-13. SM Bus Interface Signals Name Type Description SMBDATA I/OD SMBus Data: External pull-up resistor is required. SMBCLK I/OD SMBus Clock: External pull-up resistor is required. SMBALERT# / GPIO11 I SMBus Alert: This signal is used to wake the system or generate SMI#. If not used for SMBALERT#, it can be used as a GPIO. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 75 Signal Description 2.14 System Management Interface Table 2-14. System Management Interface Signals (Sheet 1 of 2) Name Type Description INTRUDER# I Intruder Detect: This signal can be set to disable system if box detected open. This signal’s status is readable, so it can be used like a GPIO if the Intruder Detection is not needed. I/OD System Management Link: SMBus link to optional external system management ASIC or LAN controller. External pull-ups are required. Note that SMLINK0 corresponds to an SMBus Clock signal, and SMLINK1 corresponds to an SMBus Data signal. SMLINK[1:0] LINKALERT# / CLGPIO4 (Digital Office Only) / GPIO60 MEM_LED / GPIO24 O OD SMLink Alert: Output of the integrated LAN controller and input to either the integrated ASF, Intel® AMT or an external management controller in order for the LAN’s SMLINK slave to be serviced. External pull-up resistor is required. This signal can instead be used as a GPIO or CLGPIO (Digital Office Only). O OD Memory LED: Provides DRAM-powered LED control. Allows for the blinking of an LED to indicate memory activity in all power states. This functionality is configured and controlled by the Intel® Management Engine. This signal can instead be used as GPIO24. SUS_PWR_ACK (Mobile Only)/ CLGPIO1 (Digital Office Only) / GPIO10 AC_PRESENT (Mobile Only)/ CLGPIO2 (Digital Office Only) / GPIO14 76 O SUS_PWR_ACK: This signal is asserted by the Intel® Management Engine to indicate when the ICH suspend well may be powered down. External 10 kΩ pull-up resistor to VccSus3_3 is required. This functionality is configured and controlled by the Management Engine. This signal can instead be used as GPIO10 in platforms that do not support Intel® AMT or ASF. This signal is used as GPIO10 or CLGPIO1 (Digital Office Only) in desktop systems. AC_PRESENT: This signal is used to indicate to the Intel® Management Engine that the platform is connected to an AC power source. This functionality is configured and controlled by the Management Engine. I This signal can instead be used as GPIO14 in platforms that do not support Intel® AMT or ASF. This signal is used as GPIO14 or CLGPIO2 (Digital Office Only) in desktop systems. NOTE: Even though the signal is controlled by the Management Engine, the host can still use this pin to generate SCI/SMI. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-14. System Management Interface Signals (Sheet 2 of 2) Name Type Description Wake On LAN Power Enable. In an Intel® AMT or ASF enabled system, this output signal is driven high by the ICH to control the LAN subsystem power (VccLAN3_3, VccCL3_3, LAN PHY Power, and SPI device) to support Wake on LAN (WOL) when the Intel® Management Engine is powered off. This functionality is configured and controlled by the Management Engine prior to entering the powered off state. WOL_EN / GPIO9 O NOTES: 1. This signal should be OR’d with the SLP_M# signal on the motherboard to determine when to power the LAN subsystem. 2. In order to support WOL out of a G3 state, the WOL_EN pin needs to be pulled high by an external resistor until the Management Engine is initialized. If ASF or AMT are disabled on a board that is configured for WOL_EN support, BIOS must utilize GPIO9 to control power to the LAN subsystem when entering S3–S5. In platforms that do not support Intel AMT or ASF, this signal is used as GPIO9. CLGPIO1 (Digital Office Only) / SUS_PWR_ACK (Mobile Only)/ GPIO10 I CLGPIO2 (Digital Office Only) / AC_PRESENT (Mobile Only) / GPIO14 I/O CLGPIO4 (Digital Office Only) / LINKALERT# / GPIO60 I/O CLGPIO5 (Digital Office Only) / This signal is used as GPIO10 in desktop systems. This signal is used as SUS_PWR_ACK in mobile systems. Controller Link General Purpose I/O 2. This signal is not used by the Intel® Management Engine in desktop systems. This signal is used as GPIO14 in desktop systems. This signal is used as AC_PRESENT in mobile systems. Controller Link General Purpose I/O 4. This signal is not used by the Intel® Management Engine in mobile and desktop systems. This signal may be used as GPIO60 or LINKALERT#. I GPIO57 CLGPIO6 (Digital Office Only) / SPI_CS1# / GPIO58 (Desktop Only) Controller Link General Purpose I/O 1. This signal is not used by the Intel® Management Engine in desktop systems. Controller Link General Purpose I/O 5. This signal is not used by the Intel® Management Engine in desktop systems. In mobile systems, this signal is asserted to indicate Physical Presence to the integrated TPM module. This signal is used as GPIO57 in desktop systems. I/O Controller Link General Purpose I/O 6. This signal is not used by the Intel® Management Engine in mobile and desktop systems. This signal may be used as a GPIO58 (Desktop Only) or SPI_CS1#. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 77 Signal Description 2.15 Real Time Clock Interface Table 2-15. Real Time Clock Interface 2.16 Name Type Description RTCX1 Special Crystal Input 1: This signal is connected to the 32.768 kHz crystal. If no external crystal is used, then RTCX1 can be driven with the desired clock rate. RTCX2 Special Crystal Input 2: This signal is connected to the 32.768 kHz crystal. If no external crystal is used, then RTCX2 should be left floating. Other Clocks Table 2-16. Other Clocks Name Type CLK14 I Oscillator Clock: Used for 8254 timers. Runs at 14.31818 MHz. This clock is permitted to stop during S3 (or lower) states. CLK48 I 48 MHz Clock: Used to run the USB controller. Runs at 48.000 MHz. This clock is permitted to stop during S3 (or lower) states. I 100 MHz Differential Clock: These signals are used to run the SATA controller at 100 MHz. This clock is permitted to stop during S3/S4/S5 states. I 100 MHz Differential Clock: These signals are used to run the Direct Media Interface. Runs at 100 MHz. SATA_CLKP SATA_CLKN DMI_CLKP, DMI_CLKN 2.17 Description Miscellaneous Signals Table 2-17. Miscellaneous Signals (Sheet 1 of 3) Name Type INTVRMEN I Description Internal Voltage Regulator Enable: This signal enables the internal VccSus1_05, VccSus1_5 and VccCL1_5 regulators. This signal must be pulled-up to VccRTC. LAN100_SLP I Internal Voltage Regulator Enable: When connected to VccRTC, this signal enables the internal voltage regulators powering VccLAN1_05 and VccCL1_05. This signal must be pulled-up to VccRTC. SPKR O Speaker: The SPKR signal is the output of counter 2 and is internally “ANDed” with Port 61h bit 1 to provide Speaker Data Enable. This signal drives an external speaker driver device, which in turn drives the system speaker. Upon PLTRST#, its output state is 0. NOTE: SPKR is sampled as a functional strap. See Section 2.24.1 for more details. There is a weak integrated pull-down resistor on SPKR pin. 78 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-17. Miscellaneous Signals (Sheet 2 of 3) Name Type Description RTC Reset: When asserted, this signal resets register bits in the RTC well. RTCRST# I NOTES: 1. Unless CMOS is being cleared (only to be done in the G3 power state), the RTCRST# input must always be high when all other RTC power planes are on. 2. In the case where the RTC battery is dead or missing on the platform, the RTCRST# pin must rise before the RSMRST# pin. Secondary RTC Reset: This signal resets the manageability register bits in the RTC well when the RTC battery is removed. NOTES: 1. The SRTCRST# input must always be high when all other RTC power planes are on. 2. In the case where the RTC battery is dead or missing on the platform, the SRTCRST# pin must rise before the RSMRST# pin. SRTCRST# I TP0 (Desktop Only) / BATLOW# (Mobile Only) I Test Point 0: This signal must have an external pull-up to VccSus3_3. TP1 (Desktop Only) / DPRSTP# (Mobile Only) O Test Point 1: Route signal to a test point. TP2 (Desktop Only) / DPSLP# (Mobile Only) O Test Point 2: Route signal to a test point. TP3 I/O Test Point 3: Route signal to a test point. TP4 (Desktop Only) / CL_DATA1 (Mobile Only) I/O Test Point 4: Route signal to a test point. TP5 (Desktop Only) / CL_CLK1 (Mobile Only) I/O Test Point 5: Route signal to a test point. TP6 (Desktop Only) / CL_VREF1 (Mobile Only) I Test Point 6: Route signal to a test point. TP7 (Desktop Only) / CL_RST1# (Mobile Only) O Test Point 7: Route signal to a test point. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 79 Signal Description Table 2-17. Miscellaneous Signals (Sheet 3 of 3) 2.18 Name Type Description TP[10:8] (Mobile Only) / PWM[2:0] (Desktop Only) OD O TP11 (Mobile Only) / SST (Desktop Only) I/O Test Point 11: Route signal to a test point. TP12 (Mobile Only) / PECI (Desktop Only) I/O Test Point 12: Route signal to a test point. Test Point [10:8]: Route signal to a test point. Intel® High Definition Audio Link Table 2-18. Intel® High Definition Audio Link Signals (Sheet 1 of 2) Name Type Description HDA_RST# O Intel® High Definition Audio Reset: Master hardware reset to external codec(s). Intel High Definition Audio Sync: 48 kHz fixed rate sample sync to the codec(s). Also used to encode the stream number. HDA_SYNC HDA_BIT_CLK O O NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for more details. There is a weak integrated pull-down resistor on this pin. Intel High Definition Audio Bit Clock Output: 24.000 MHz serial data clock generated by the Intel High Definition Audio controller (the Intel® ICH9). This signal has a weak internal pulldown resistor. Intel High Definition Audio Serial Data Out: Serial TDM data output to the codec(s). This serial output is double-pumped for a bit rate of 48 Mb/s for Intel High Definition Audio. HDA_SDOUT O NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for more details. There is a weak integrated pull-down resistor on this pin. 80 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-18. Intel® High Definition Audio Link Signals (Sheet 2 of 2) Name Type HDA_SDIN[3:0] Description Intel High Definition Audio Serial Data In [3:0]: Serial TDM data inputs from the codecs. The serial input is single-pumped for a bit rate of 24 Mb/s for Intel® High Definition Audio. These signals have integrated pull-down resistors, which are always enabled. I NOTE: During enumeration, the ICH will drive this signal. During normal operation, the CODEC will drive it. HDA_DOCK_EN# (Mobile Only) / GPIO33 High Definition Audio Dock Enable: This signal controls the external Intel HD Audio docking isolation logic. This is an active low signal. When deasserted the external docking switch is in isolate mode. When asserted the external docking switch electrically connects the Intel HD Audio dock signals to the corresponding Intel® ICH9 signals. O This signal can instead be used as GPIO33. NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for more details. HDA_DOCK_RST# (Mobile Only) / GPIO34 High Definition Audio Dock Reset: This signal is a dedicated HDA_RST# signal for the codec(s) in the docking station. Aside from operating independently from the normal HDA_RST# signal, it otherwise works similarly to the HDA_RST# signal. O This signal can instead be used as GPIO34. 2.19 Serial Peripheral Interface (SPI) Table 2-19. Serial Peripheral Interface (SPI) Signals Name Type SPI_CS0# O Description SPI Chip Select 0: Used as the SPI bus request signal. SPI Chip Select 1: Used as the SPI bus request signal. Signal can also be used as a CLGPIO6 (Digital Office Only) or GPIO58 (Desktop Only). SPI_CS1# / CLGPIO6 (Digital Office Only)/ GPIO58 (desktop Only) O SPI_MISO I NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for more details. There is a weak integrated pull-up resistor on this pin. SPI Master IN Slave OUT: Data input pin for ICH9. SPI Master OUT Slave IN: Data output pin for ICH9. SPI_MOSI O SPI_CLK O NOTE: This signal is sampled as a functional strap. See Section 2.24.1 for more details. There is a weak integrated pull-down resistor on this pin. SPI Clock: SPI clock signal, during idle the bus owner will drive the clock signal low. 17.86 MHz and 31.25 MHz. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 81 Signal Description 2.20 Controller Link Table 2-20. Controller Link Signals Signal Name Type Description CL_CLK0 I/O Controller Link Clock 0: bi-directional clock that connects to the (G)MCH. CL_DATA0 I/O Controller Link Data 0: bi-directional data that connects to the (G)MCH. CL_VREF0 I Controller Link Reference Voltage 0: External reference voltage for Controller Link 0. CL_RST0# O Controller Link Reset 0: North Controller Link reset that connects to the (G)MCH. O Controller Link Reset 1: South Controller Link reset that connects to a Wireless LAN Device supporting Intel® Active Management Technology. CL_RST1# (Mobile Only) / TP7 (Desktop Only) 82 CL_CLK1 (Mobile Only) / TP5 (Desktop Only) I/O Controller Link Clock 1: bi-directional clock that connects to a Wireless LAN Device supporting Intel® Active Management Technology. CL_DATA1 (Mobile Only) / TP4 (Desktop Only) I/O Controller Link Data 1: bi-directional data that connects to a Wireless LAN Device supporting Intel® Active Management Technology. CL_VREF1 (Mobile Only) / TP6 (Desktop Only) I Controller Link Reference Voltage 1: External reference voltage for Controller Link 1. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description 2.21 Intel® Quiet System Technology (Desktop Only) Table 2-21. Intel® Quiet System Technology Signals Signal Name PWM[2:0] (Desktop Only) / TP[10:8] (Mobile Only) Type Description Fan Pulse Width Modulation Outputs: Pulse Width Modulated duty cycle output signal that is used for Intel® Quiet System Technology. OD O When controlling a 3-wire fan, this signal controls a power transistor that, in turn, controls power to the fan. When controlling a 4-wire fan, this signal is connected to the “Control” signal on the fan. The polarity of this signal is programmable. The output default is low. These signals are 5 V tolerant. TACH0 / (Desktop Only) GPIO17 TACH1 / (Desktop Only) GPIO1 I TACH2 / (Desktop Only) GPIO6 Fan Tachometer Inputs: Tachometer pulse input signal that is used to measure fan speed. This signal is connected to the “Sense” signal on the fan. Can instead be used as a GPIO. TACH3 / (Desktop Only) GPIO7 SST (Desktop Only) / TP11 (Mobile Only) I/O Simple Serial Transport: Single-wire, serial bus. Connect to SST compliant devices such as SST thermal sensors or voltage sensors. I/O Platform Environment Control Interface: Single-wire, serial bus. Connect to corresponding pin of the processor for accessing processor digital thermometer. PECI (Desktop Only) / TP12 (Mobile Only) 2.22 General Purpose I/O Signals Table 2-22. General Purpose I/O Signals (Sheet 1 of 3) Name Type Tolerance Power Well Default GPIO60 I/O 3.3 V Suspend Native Multiplexed with LINKALERT#, or can be used as CLGPIO4 (Digital Office Only). (Note 11). GPIO59 I/O 3.3 V Suspend Native Multiplexed with OC[0]#. (Note 11). GPIO58 (Desktop Only) I/O 3.3 V Suspend (Note 6) GPI Multiplexed with SPI_CS1# or can be used as CLGPIO6 (Digital Office Only) (Note 8 and 10). GPIO57 I/O 3.3 V Suspend GPI Unmultiplexed. Can be used as CLGPIO5 (Digital Office Only). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Description 83 Signal Description Table 2-22. General Purpose I/O Signals (Sheet 2 of 3) Name Type Tolerance Power Well Default GPIO56 I/O 3.3 V Suspend GPI GPIO55 I/O 3.3 V Core Native Multiplexed with GNT3# (Note 8). GPIO54 I/O 5.0 V Core Native Multiplexed with REQ3#. (Note 11). GPIO53 I/O 3.3 V Core Native Multiplexed with GNT2# (Note 8). GPIO52 I/O 5.0 V Core Native Multiplexed with REQ2#. (Note 11). GPIO51 I/O 3.3 V Core Native Multiplexed with GNT1# (Note 8). GPIO50 I/O 5.0 V Core Native Multiplexed with REQ1#. (Note 11). GPIO49 I/O 3.3V Core GPO GPIO48 I/O 3.3 V Core GPI GPIO[47:44] I/O 3.3V Suspend Native Multiplexed with OC[11:8]#. (Note 11). GPIO[43:40] I/O 3.3 V Suspend Native Multiplexed with OC[4:1]#. (Note 11). GPIO39 I/O 3.3 V Core GPI Multiplexed with SDATAOUT0. GPIO38 I/O 3.3 V Core GPI Multiplexed with SLOAD. GPIO37 I/O 3.3 V Core GPI GPIO36 I/O 3.3 V Core GPI GPIO35 I/O 3.3 V Core GPO Multiplexed with SATACLKREQ#. GPIO34 I/O 3.3 V Core GPO Mobile: Multiplexed with HDA_DOCK_RST#. Description Unmultiplexed Unmultiplexed (Note 8). Multiplexed with SDATAOUT1. Desktop: Multiplexed with SATA3GP. Mobile: Multiplexed with SATA5GP. Desktop: Multiplexed with SATA2GP. Mobile: Multiplexed with SATA4GP. Desktop: UnMultiplexed. GPIO33 I/O 3.3 V Core GPO Mobile: Multiplexed with HDA_DOCK_EN#. GPO Mobile: This GPIO is not implemented and is used instead as CLKRUN#. Desktop: UnMultiplexed. GPIO32 (Desktop Only) 3.3 V Core Desktop: UnMultiplexed. GPIO31 I/O 3.3 V Suspend Native Multiplexed with OC7#. (Note 11). GPIO30 I/O 3.3 V Suspend Native Multiplexed with OC6#. (Note 11). GPIO29 I/O 3.3 V Suspend Native Multiplexed with OC5#. (Note 11). GPIO28 I/O 3.3 V Suspend GPO Unmultiplexed. GPIO27 I/O 3.3 V Suspend GPO Unmultiplexed GPIO26 I/O 3.3 V Suspend Native GPIO25 I/O 3.3 V Suspend Native GPIO24 I/O 3.3 V Suspend GPO GPIO23 I/O 3.3 V Core Native (Desktop Only) 84 I/O Multiplexed with S4_STATE#. (Note 9) Mobile: This GPIO is not implemented and is used instead as STP_CPU#. Desktop: Default as STP_CPU# (Note 4). Can be used as MEM_LED. GPIO24 configuration register bits are not cleared by CF9h reset event. Multiplexed with LDRQ1#. (Note 11). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-22. General Purpose I/O Signals (Sheet 3 of 3) Name Type Tolerance Power Well Default GPIO22 I/O 3.3 V Core GPI GPIO21 I/O 3.3 V Core GPI Multiplexed with SATA0GP. GPIO20 I/O 3.3 V Core GPO Unmultiplexed. (Note 8) GPIO19 I/O 3.3 V Core GPI Multiplexed with SATA1GP. GPIO18 I/O 3.3 V Core GPO Unmultiplexed. GPIO17 I/O 3.3 V Core GPI Core Native (Mobile) / GPO (Desktop) GPIO16 GPIO15 I/O 3.3 V I/O 3.3 V Suspend Native GPIO14 I/O 3.3 V Suspend GPI GPIO13 I/O 3.3 V Suspend GPI (Desktop Only) Description Multiplexed with SCLOCK. Desktop: Multiplexed with TACH0. Mobile: Unmultiplexed Mobile: Natively used as DPRSLPVR. Desktop: UnMultiplexed. Mobile: GPIO is not implemented and is used instead as STP_PCI#. Desktop: Default as STP_PCI#. (Note 4). Mobile: Can be used as AC_PRESENT GPIO12 I/O 3.3 V Suspend GPO (Desktop) GPIO11 I/O 3.3 V Suspend Native GPIO10 I/O 3.3 V Suspend GPI Desktop: Unmultiplexed. Can be used as CLGPIO2 (Digital Office Only). Unmultiplexed. Mobile: LAN_PHY_PWR_CTRL. Desktop: UnMultiplexed. Multiplexed with SMBALERT#. (Note 11). Mobile: Can be used as SUS_PWR_ACK. GPIO9 I/O 3.3 V Suspend Native GPIO8 I/O 3.3 V Suspend GPI GPIO[7:6] I/O 3.3 V Core GPI GPIO[5:2] I/OD 5V Core GPI GPIO1 I/O 3.3 V Core GPI GPIO0 I/O 3.3 V Core GPI Desktop: Unmultiplexed. Can be used as CLGPIO1 (Digital Office Only). Can be used as WOL_EN. Unmultiplexed. Desktop: Multiplexed with TACH[3:2]. Mobile: Unmultiplexed Multiplexed with PIRQ[H:E]# (Note 6). Desktop: Multiplexed with TACH1. Mobile: Unmultiplexed Mobile: Multiplexed with PMSYNC#. Desktop: Unmultiplexed NOTES: 1. All GPIOs can be configured as either input or output. 2. GPI[15:0] can be configured to cause a SMI# or SCI. Note that a GPI can be routed to either an SMI# or an SCI, but not both. 3. Some GPIOs exist in the VccSus3_3 power plane. Care must be taken to make sure GPIO signals are not driven high into powered-down planes. Also, external devices should not be driving powered down GPIOs high. Some ICH9 GPIOs may be connected to pins on devices that exist in the core well. If these GPIOs are outputs, there is a danger that a loss of core Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 85 Signal Description 4. 5. 6. 7. 8. 9. 10. 11. 2.23 power (PWROK low) or a Power Button Override event will result in the Intel ICH9 driving a pin to a logic 1 to another device that is powered down. The functionality that is multiplexed with the GPIO may not be utilized in desktop configuration. This GPIO is not an open-drain when configured as an output. SPI_CS1# and CLGPIO6 (Digital Office Only) are located in the VccCL3_3 well. When this signal is configured as GPO the output stage is an open drain. This signal is sampled as a functional strap. See Section 2.24.1 for more details. The GPIO_USE_SEL bit for this signal is overridden by bit 8 in the GEN_PMCON_3 Register (D31:F0). The GPIO_USE_SEL bit for this is ignored. Functionality is set by bits 9:8 of FLMAP0 register. When the multiplexed GPIO is used as GPIO functionality, care should be taken to ensure the signal is stable in its inactive state of the native functionality, immediately after reset until it is initialized to GPIO functionality. Power and Ground Signals Table 2-23. Power and Ground Signals (Sheet 1 of 3) Name Description V5REF Reference for 5 V tolerance on core well inputs. This power may be shut off in S3, S4, S5 or G3 states. V5REF_Sus Reference for 5 V tolerance on suspend well inputs. This power is not expected to be shut off unless the system is unplugged in desktop configurations or the main battery is removed or completely drained and AC power is not available in mobile configurations. Vcc1_05 1.05 V supply for core well logic. This power may be shut off in S3, S4, S5 or G3 states. Vcc1_5_A 1.5 V supply for Logic and I/O. This power may be shut off in S3, S4, S5 or G3 states. Vcc1_5_B 1.5 V supply for Logic and I/O. This power may be shut off in S3, S4, S5 or G3 states. Vcc3_3 VccCL1_05 VccCL1_5 VccCL3_3 VccDMI VccDMIPLL 86 3.3 V supply for core well I/O buffers. This power may be shut off in S3, S4, S5 or G3 states. 1.05V supply for Controller Link. This plane must be on in S0 and other times Controller Link is used. This voltage is generated internally. This pin can be left as No Connect unless decoupling is required. 1.5V supply for Controller Link. This plane must be on in S0 and other times Controller Link is used. This voltage is generated internally. This pin can be left as No Connect unless decoupling is required. 3.3V supply for Controller Link. This is a separate power plane that may or may not be powered in S3–S5 states. This plane must be on in S0 and other times Controller Link is used. NOTE: VccCL3_3 must always be powered when VccLAN3_3 is powered. Power supply for DMI. 1.05V, 1.25V or 1.5V depending on (G)MCH’s DMI voltage. 1.5 V supply for core well logic. This signal is used for the DMI PLL. This power may be shut off in S3, S4, S5 or G3 states. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-23. Power and Ground Signals (Sheet 2 of 3) Name Description VccGLAN1_5 1.5V supply for integrated Gigabit LAN I/O buffers. This power is on in S0 and is turned off in S3, S4, S5, even if integrated Gigabit LAN is not used. VccGLAN3_3 3.3V supply for integrated Gigabit LAN logic and I/O. This power is on in S0 and is turned off in S3, S4, S5, even if integrated Gigabit LAN is not used. VccGLANPLL 1.5V supply for core well logic. This signal is used for the integrated Gigabit LAN PLL. This power is shut off in S3, S4, S5 and G3 states. VccHDA VccLAN1_05 VccLAN3_3 VccRTC VccSATAPLL VccSus1_05 Core supply for Intel® High Definition Audio. This pin can be either 1.5 or 3.3 V. This power may be shut off in S3, S4, S5 or G3 states. NOTE: VccSusHDA and VccHDA can be connected to either 1.5 V or 3.3 V supplies, but both pins must be connected to supplies that are the same nominal value. 1.05 V supply for LAN controller logic. This is a separate power plane that may or may not be powered in S3–S5 states. This voltage is generated internally. These pins can be left as No Connect unless decoupling is required. 3.3 V supply for LAN Connect interface buffers. This is a separate power plane that may or may not be powered in S3–S5 states. This plane must be on in S0. NOTE: VccLAN3_3 must always be powered when VccCL3_3 or Vcc3_3 is powered. 3.3 V (can drop to 2.0 V min. in G3 state) supply for the RTC well. This power is not expected to be shut off unless the RTC battery is removed or completely drained. Note: Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. Clearing CMOS in an Intel® ICH9-based platform can be done by using a jumper on RTCRST# or GPI. 1.5 V supply for core well logic. This signal is used for the SATA PLL. This power may be shut off in S3, S4, S5 or G3 states. Must be powered even if SATA is not used. 1.05 V supply for suspend well logic. This power is not expected to be shut off unless the system is unplugged in desktop configurations or the main battery is removed or completely drained and AC power is not available in mobile configurations. This voltage is generated internally. These pins can be left as No Connects unless decoupling is required. VccSus1_5 1.5V supply for the suspend well I/O. This power is not expected to be shut off unless the system is unplugged in desktop configurations. This voltage is generated internally. These pins can be left as No Connects unless decoupling is required. VccSus3_3 3.3 V supply for suspend well I/O buffers. This power is not expected to be shut off unless the system is unplugged in desktop configurations or the main battery is removed or completely drained and AC power is not available in mobile configurations. VccSusHDA Suspend supply for Intel® High Definition Audio. This pin can be either 1.5 or 3.3 V. This power is not expected to be shut off unless the system is unplugged in desktop configurations or the main battery is removed or completely drained and AC power is not available in mobile configurations. NOTE: VccSusHDA and VccHDA can be connected to either 1.5 V or 3.3 V supplies, but both pins must be connected to supplies that are the same nominal value. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 87 Signal Description Table 2-23. Power and Ground Signals (Sheet 3 of 3) Name Description VccUSBPLL 1.5 V supply for core well logic. This signal is used for the USB PLL. This power may be shut off in S3, S4, S5 or G3 states. Must be powered even if USB not used. Vss Grounds. V_CPU_IO Powered by the same supply as the processor I/O voltage. This supply is used to drive the processor interface signals listed in Table 2-12. 2.24 Pin Straps 2.24.1 Functional Straps The following signals are used for static configuration. They are sampled at the rising edge of PWROK to select configurations (except as noted), and then revert later to their normal usage. To invoke the associated mode, the signal should be driven at least four PCI clocks prior to the time it is sampled. Table 2-24. Functional Strap Definitions (Sheet 1 of 3) Comment Usage HDA_SDOUT XOR Chain Entrance / PCI Express* Port Config 1 bit 1 (Port 1-4) Rising Edge of PWROK HDA_SYNC PCI Express Port Config 1 bit 0 (Port 1-4) Rising Edge of PWROK GNT2# / GPIO53 PCI Express Port Config 2 bit 2 (Port 5-6) Rising Edge of PWROK GPIO20 Reserved Rising Edge of PWROK This signal has a weak internal pull-down. NOTE: This signal should not be pulled high Rising edge of PWROK Tying this strap low configures DMI for ESIcompatible operation. This signal has a weak internal pull-up. NOTE: ESI compatible mode is for server platforms only. This signal should not be pulled low for desktop and mobile. Rising Edge of PWROK The signal has a weak internal pull-up. If the signal is sampled low, this indicates that the system is strapped to the “top-block swap” mode (Intel® ICH9 inverts A16 for all cycles targeting BIOS space). The status of this strap is readable via the Top Swap bit (Chipset Config Registers:Offset 3414h:bit 0). Note that software will not be able to clear the Top-Swap bit until the system is rebooted without GNT3# being pulled down. GNT1#/GPIO51 GNT3# / GPIO55 88 When Sampled Signal ESI Strap (Server Only) Top-Block Swap Override Allows entrance to XOR Chain testing when TP3 pulled low at rising edge of PWROK. When TP3 not pulled low at rising edge of PWROK, sets bit 1 of RPC.PC (Chipset Config Registers:Offset 224h).This signal has a weak internal pull-down. This signal has a weak internal pull-down. Sets bit 0 of RPC.PC (Chipset Config Registers:Offset 224h) This signal has a weak internal pull-up. Sets bit 2 of RPC.PC2 (Chipset Config Registers:Offset 0224h) when sampled low. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Signal Description Table 2-24. Functional Strap Definitions (Sheet 2 of 3) Signal Usage When Sampled Comment This field determines the destination of accesses to the BIOS memory range. Signals have weak internal pull-ups. Also controllable via Boot BIOS Destination bit (Chipset Config Registers:Offset 3410h:bit 11). This strap is used in conjunction with Boot BIOS Destination Selection 0 strap. GNT0# Boot BIOS Destination Selection 1 Rising Edge of PWROK Bit11 (GNT0#) Bit 10 (SPI_CS1#) Boot BIOS Destination 0 1 SPI 1 0 PCI 1 1 LPC 0 0 Reserved NOTE: Booting to PCI is intended for debug/testing only. Boot BIOS Destination Select to LPC/PCI by functional strap or via Boot BIOS Destination Bit will not affect SPI accesses initiated by Management Engine or Integrated GbE LAN. This field determines the destination of accesses to the BIOS memory range. Signals have weak internal pull-ups. Also controllable via Boot BIOS Destination bit (Chipset Config Registers:Offset 3410h:bit 10). This strap is used in conjunction with Boot BIOS Destination Selection 1 strap. Bit11 SPI_CS1# / GPIO58 Desktop Only) / CLGPIO6 (Digital Office Only) Boot BIOS Destination Selection 0 Rising Edge of CLPWROK (GNT0#) Bit 10 (SPI_CS1#) Boot BIOS Destination 0 1 SPI 1 0 PCI 1 1 LPC 0 0 Reserved NOTE: Booting to PCI is intended for debug/testing only. Boot BIOS Destination Select to LPC/PCI by functional strap or via Boot BIOS Destination Bit will not affect SPI accesses initiated by Management Engine or Integrated GbE LAN. SATALED# PCI Express Lane Reversal (Lanes 1-4) Rising Edge of PWROK Signal has weak internal pull-up. Sets bit 27 of MPC.LR (Device 28: Function 0: Offset D8) SPKR No Reboot Rising Edge of PWROK The signal has a weak internal pull-down. If the signal is sampled high, this indicates that the system is strapped to the “No Reboot” mode (ICH9 will disable the TCO Timer system reboot feature). The status of this strap is readable via the NO REBOOT bit (Chipset Config Registers:Offset 3410h:bit 5). TP3 Reserved Rising Edge of PWROK This signal has a weak internal pull-up. This signal should not be pulled low. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 89 Signal Description Table 2-24. Functional Strap Definitions (Sheet 3 of 3) When Sampled Comment GPIO33 / HDA_DOCK_EN# (Mobile Only) Flash Descriptor Security Override Strap Rising Edge of PWROK This signal has a weak internal pull-up resistor. If sampled low, the Flash Descriptor Security will be overridden. If high, the security measures defined in the Flash Descriptor will be in effect. NOTE: This strap should only be enabled in manufacturing environments. GPIO49 DMI Termination Voltage Rising Edge of PWROK The signal is required to be low for desktop applications and required to be high for mobile applications. SPI_MOSI Reserved Rising Edge of CLPWROK This signal has a weak internal pull-down resistor. This signal should not be pulled high. Rising Edge of CLPWROK This signal has a weak internal pull-down resistor. When the signal is sampled low the Integrated TPM will be disabled. When the signal is sampled high, the MCH TPM enable strap is sampled low and the TPM Disable bit is clear, the Integrated TPM will be enabled. NOTE: This signal is required to be floating or pulled low for desktop applications. Signal Usage SPI_MOSI (Moble Only) Integrated TPM Enable NOTE: See Section 3.1 for full details on pull-up/pull-down resistors. 2.24.2 External RTC Circuitry To reduce RTC well power consumption, the ICH9 implements an internal oscillator circuit that is sensitive to step voltage changes in VccRTC. Figure 2-3 shows an example schematic recommended to ensure correct operation of the ICH9 RTC. Figure 2-3. Example External RTC Circuit 3.3V Sus VCCRTC Schottky Diodes 1uF 0.1uF RTCX2 1 KΩ Vbatt 20 KΩ 20 KΩ R1 10MΩ 32.768 KHz Xtal RTCX1 1.0 uF C1 1.0 uF C2 RTCRST# SRTCRST# NOTE: C1 and C2 depend on crystal load. § 90 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States 3 Intel® ICH9 Pin States 3.1 Integrated Pull-Ups and Pull-Downs Table 3-1. Integrated Pull-Up and Pull-Down Resistors Resistor Nominal Notes CL_CLK[1:0] Signal Pull-up 20K 13 CL_DATA[1:0] Pull-up 20k 13 CL_RST0# Pull-up 10K 4 DPRSLPVR (Mobile Only)/GPIO16 Pull-down 20K 2, 10 HDA_BIT_CLK Pull-down 20K 1, 9 Pull-up 20k 3,7 HDA_RST# Pull-down 20K 2 HDA_SDIN[3:0] Pull-down 20K 2 HDA_SDOUT Pull-down 20K 2, 7 HDA_SYNC Pull-down 20K 2, 7 Pull-up 20K 3, 11, 12 Pull-down 20K 3, 7 HDA_DOCK_EN# (Mobile Only)/GPIO33 GNT0#, GNT[3:1]#/GPIO[55,53,51] GPIO20 GPIO49 Pull-up 20k 3, 7 LAD[3:0]# / FHW[3:0]# Pull-up 20K 3 LAN_RXD[2:0] Pull-up 20K 4 LDRQ0 Pull-up 20K 3 LDRQ1 / GPIO23 Pull-up 20K 3 PME# Pull-up 20K 3 PWRBTN# Pull-up 20K 3 SATALED# Pull-up 15K 8 SPI_CS1# / GPIO58 (Desktop Only) / CLGPIO6 (Digital Office Only) Pull-up 20K 3, 10 Pull-down 20K 3, 7 SPI_MOSI SPI_MISO Pull-up 20K 3 Pull-down 20K 2 TACH[3:0] Pull-up 20K 3 TP3 Pull-up 20K 6 Pull-down 15K 5 SPKR USB[11:0] [P,N] NOTES: 1. Simulation 2. Simulation 3. Simulation 4. Simulation 5. Simulation data data data data data shows shows shows shows shows Intel® I/O Controller Hub 9 (ICH9) Family Datasheet that that that that that these these these these these resistor resistor resistor resistor resistor values values values values values can can can can can range range range range range from from from from from 10 kΩ to 40 kΩ. 9 kΩ to 50 kΩ. 15 kΩ to 35 kΩ. 7.5kΩ to 16kΩ. 14.25 kΩ to 24.8 kΩ 91 Intel® ICH9 Pin States 6. 7. 8. 9. 10. 11. 12. 13. 3.2 Simulation data shows that these resistor values can range from 10 kΩ The pull-up or pull-down on this signal is only enabled at boot/reset for Simulation data shows that these resistor values can range from 10 kΩ internal pull-up is only enabled during PLTRST# assertion. The pull-down on this signal is only enabled when in S3. The pull-up or pull-down on this signal is only enabled during reset. The pull-up on this signal is not enabled when PCIRST# is high. The pull-up on this signal is enabled when the core power is valid. Simulation data shows that these resistor values can range from 15 kΩ to 30 kΩ. strapping function. to 20 kΩ. The to 31 kΩ. Output and I/O Signals Planes and States Table 3-2 and Table 3-3 shows the power plane associated with the output and I/O signals, as well as the state at various times. Within the table, the following terms are used: Note: “High-Z” Tri-state. ICH9 not driving the signal high or low. “High” ICH9 is driving the signal to a logic 1. “Low” ICH9 is driving the signal to a logic 0. “Defined” Driven to a level that is defined by the function or external pullup/pull-down resistor (will be high or low). “Undefined” ICH9 is driving the signal, but the value is indeterminate. “Running” Clock is toggling or signal is transitioning because function not stopping. “Off” The power plane is off; ICH9 is not driving when configured as an output or sampling when configured as an input. “Input” ICH9 is sampling and signal state determined by external driver. Signal levels are the same in S4 and S5, except as noted. ICH9 suspend well signal states are indeterminate and undefined and may glitch prior to RSMRST# deassertion. This does not apply to LAN_RST#, SLP_S3#, SLP_S4#, S4_STATE# and SLP_S5#. These signals are determinate and defined prior to RSMRST# deassertion. ICH9 core well signal states are indeterminate and undefined and may glitch prior to PWROK assertion. This does not apply to FERR# and THRMTRIP#. These signals are determinate and defined prior to PWROK assertion. 92 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States Table 3-2. Power Plane and States for Output and I/O Signals for Desktop Configurations (Sheet 1 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 S1 S3 S4/S5 High8 Defined Off Off High Defined Off Off PCI Express* PETp[5:1], PETn[5:1], PETp6 / GLANTXp, PETn6 / GLANTXn Core High DMI DMI[3:0]TXP, DMI[3:0]TXN Core High PCI Bus AD[31:0] Core Low Undefined Defined Off Off C/BE[3:0]# Core Low Undefined Defined Off Off DEVSEL# Core High-Z High-Z High-Z Off Off FRAME# Core High-Z High-Z High-Z Off Off GNT0# , GNT[3:1]#11/ GPIO[55, 53, 51] Core High-Z High High Off Off IRDY#, TRDY# Core High-Z High-Z High-Z Off Off PAR Core Low Undefined Defined Off Off PCIRST# Suspend Low High High Low Low 11 PERR# Core High-Z High-Z High-Z Off Off PLOCK# Core High-Z High-Z High-Z Off Off STOP# Core High-Z High-Z High-Z Off Off LPC Interface LAD[3:0] / FWH[3:0] Core High High High Off Off LFRAME# / FWH[4] Core High High High Off Off LPCPD# / SUS_STAT# Suspend Low High High Low Low High Off Off Firmware Hub INIT3_3V# Core High High LAN Connect Interface LAN_RSTSYNC LAN High Low Defined Defined Defined LAN_TXD[2:0] LAN Low Low Defined Defined Defined Gigabit LAN Connect Interface GLAN_TXp / PETp6, GLAN_TXn / PETn6 GLAN High High Defined Off Off LAN_RSTSYNC LAN High Low Defined Defined Defined Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 93 Intel® ICH9 Pin States Table 3-2. Power Plane and States for Output and I/O Signals for Desktop Configurations (Sheet 2 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 S1 S3 S4/S5 SATA Interface SATA[5:0]TXP, SATA[5:0]TXN Core High-Z High-Z Defined Off Off SATALED#11 Core High-Z High-Z Defined Off Off SATARBIAS Core High-Z High-Z Defined Off Off SATACLKREQ# / GPIO35 Core Low Low Defined Off Off SCLOCK/GPIO22 Core Input Input Defined Off Off SLOAD/GPIO38 Core Input Input Defined Off Off SDATAOUT[1:0]/ GPIO[48,39] Core Input Input Defined Off Off Interrupts PIRQ[A:D]#, Core High-Z High-Z High-Z Off Off PIRQ[H:E]# / GPIO[5:2] Core Input Input Defined Off Off SERIRQ Core High-Z High-Z High-Z Off Off USB Interface USB[11:0][P,N] Suspend Low Low Defined Defined Defined USBRBIAS Suspend High-Z High-Z Defined Defined Defined Power Management 94 PLTRST# Suspend Low High High Low Low SLP_M#9 Suspend Low High High Defined Defined SLP_S3# Suspend Low High High Low Low SLP_S4# Suspend Low High High High Defined S4_STATE# / GPIO26 Suspend Low Defined Defined Defined Defined SLP_S5# Suspend Low High High High Low6 SUS_STAT# / LPCPD# Suspend Low High High Low Low SUSCLK Suspend Low CK_PWRGD Suspend Low High High Low Low STP_PCI# / GPIO15 Suspend High High Defined Defined Defined STP_CPU# / GPIO25 Suspend High High Defined Defined Defined Running Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States Table 3-2. Power Plane and States for Output and I/O Signals for Desktop Configurations (Sheet 3 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 S1 S3 S4/S5 Processor Interface A20M# CPU Dependant on A20GATE Signal See Note 1 High Off Off CPUPWRGD CPU Low3 High High Off Off IGNNE# CPU High See Note 1 High Off Off INIT# CPU High High High Off Off INTR CPU See Note 5 See Note 5 Low Off Off NMI CPU See Note 5 See Note 5 Low Off Off SMI# CPU High High High Off Off STPCLK# CPU High High Low Off Off Defined Defined Defined SMBus Interface SMBCLK, SMBDATA Suspend High-Z High-Z System Management Interface LINKALERT# / CLGPIO4 (Digital Office Only) / GPIO60 Suspend High-Z High-Z Defined Defined Defined SMLINK[1:0] Suspend High-Z High-Z Defined Defined Defined Defined Off Off Miscellaneous Signals SPKR11 Core High-Z Intel® Low High Definition Audio Interface HDA_RST# HDA Suspend Low Low7 Defined Low Low HDA_SDOUT11 HDA Low Low Low Off Off HDA_SYNC HDA Low Low Low Off Off HDA_BIT_CLK HDA Low Low Low Off Off UnMultiplexed GPIO Signals GPIO0 Core Input Input Defined Off Off GPIO8 Suspend Input Input Defined Defined Defined GPIO9 Suspend High-Z High-Z Defined Defined Defined GPIO10 Suspend Input Input Defined Defined Defined GPIO12 Suspend Low Low Defined Defined Defined GPIO13 Suspend Input Input Defined Defined Defined GPIO14 Suspend Input Input Defined Defined Defined GPIO16 Core Low Low Defined Off Off GPIO18 Core High See Note 2 Defined Off Off Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 95 Intel® ICH9 Pin States Table 3-2. Power Plane and States for Output and I/O Signals for Desktop Configurations (Sheet 4 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 S1 S3 S4/S5 GPIO2011 Core Low High Defined Off Off GPIO24 Suspend Low Low Defined Defined Defined GPIO[28:27] Suspend Low Low Defined Defined Defined 11, Core High High Defined Off Off Core Low Low Defined Off Off Core High High Defined Off Off GPIO56 Suspend Input Input Defined Defined Defined GPIO57 Suspend Input Input Defined Defined Defined GPIO33 GPIO32 GPIO34 GPIO49 11 SPI Interface SPI_CS0# Controller Link High High Defined Defined Defined SPI_CS1#11 / GPIO58 / CLGPIO6 (Digital Office Only) Controller Link High High Defined Defined Defined SPI_MOSI11 Controller Link Low Low Defined Defined Defined SPI_CLK Controller Link Low Low Running Defined Defined Controller Link CL_CLK0 Controller Link Low Low Defined10 Defined10 Defined10 CL_DATA0 Controller Link Low Low Defined10 Defined10 Defined10 CL_RST0# Suspend Low High Defined10 Defined10 Defined10 Intel® Quiet System Technology PWM[2:0] Core High-Z Low Defined Off Off SST Controller Link High-Z Low Defined Off Off PECI CPU High-Z Low Defined Off Off NOTES: 1. ICH9 drives these signals High after the processor Reset 2. GPIO[18] will toggle at a frequency of approximately 1 Hz when the ICH9 comes out of reset 3. CPUPWRGD represents a logical AND of the ICH9’s VRMPWRGD and PWROK signals, and thus will be driven low by ICH9 when either VRMPWRGD or PWROK are inactive. 4. The states of Core and processor signals are evaluated at the times During PLTRST# and Immediately after PLTRST#. The states of the LAN and GLAN signals are evaluated at the times During LAN_RST# and Immediately after LAN_RST#. The states of the Controller Link signals are taken at the times During CL_RST# and Immediately after CL_RST#. The states of the Suspend signals are evaluated at the times During RSMRST# and Immediately after RSMRST#. The states of the HDA signals are evaluated at the times During HDA_RST# and Immediately after HDA_RST#. 96 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States 5. 6. 7. 8. 9. 10. 11. Table 3-3. ICH9 drives these signals Low before PWROK rising and Low after the processor Reset. SLP_S5# signals will be high in the S4 state. Low until Intel High Definition Audio Controller Reset bit set (D27:F0:Offset HDBAR+08h:bit 0), at which time HDA_RST# will be High and HDA_BIT_CLK will be Running. PETp/n[6:1] high until port is enabled by software. The SLP_M# state will be determined by Intel AMT Policies. The state of signals in S3-5 will be defined by Intel AMT Policies. This signal is sampled as a functional strap during reset. Power Plane and States for Output and I/O Signals for Mobile Configurations (Sheet 1 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 C3/C4/ C5/C6 S1 S3 S4/S5 Defined Defined Off Off Defined Defined Off Off PCI Express* PETp[5:1], PETn[5:1] PETp6 / GLANTXp, PETn6 / GLANTXn Core High8 High DMI DMI[3:0]TXP, DMI[3:0]TXN Core High High PCI Bus AD[31:0] Core Low Undefined Defined Defined Off Off C/BE[3:0]# Core Low Undefined Defined Defined Off Off CLKRUN# Core Low Low Defined Off Off Off DEVSEL# Core High-Z High-Z High-Z High-Z Off Off FRAME# Core High-Z High-Z High-Z High-Z Off Off GNT0# , GNT[3:1]#11 / GPIO[55, 53, 51] Core High High High High Off Off IRDY#, TRDY# Core High-Z High-Z High-Z High-Z Off Off PAR Core Low Undefined Defined Defined Off Off PCIRST# Suspend Low High High High Low Low PERR# Core High-Z High-Z High-Z High-Z Off Off PLOCK# Core High-Z High-Z High-Z High-Z Off Off STOP# Core High-Z High-Z High-Z High-Z Off Off 11 LPC Interface LAD[3:0] / FWH[3:0] Core High High High High Off Off LFRAME# / FWH[4] Core High High High High Off Off LPCPD# / SUS_STAT# Suspend Low High High High Low Low Defined Defined Defined LAN Connect Interface LAN_RSTSYNC LAN High Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Low Defined 97 Intel® ICH9 Pin States Table 3-3. Power Plane and States for Output and I/O Signals for Mobile Configurations (Sheet 2 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 C3/C4/ C5/C6 S1 S3 S4/S5 LAN_TXD[2:0] LAN Low Low Defined Defined Defined Defined Gigabit LAN Connect Interface GLAN_TXp / PET6p, GLAN_TXn / PET6n GLAN High High Defined Defined Off Off LAN_RSTSYNC LAN High Low Defined Defined Off Off SATA Interface SATA[5:4, 1:0]TXP, SATA[5:4, 1:0]TXN Core High-Z High-Z Defined Defined Off Off SATALED#11 Core High-Z High-Z Defined Defined Off Off SATARBIAS Core High-Z High-Z Defined Defined Off Off SATACLKREQ# / GPIO35 Core Low Low Defined Defined Off Off SCLOCK / GPIO22 Core Input Input Defined Defined Off Off SLOAD / GPIO38 Core Input Input Defined Defined Off Off SDATAOUT[1:0] / GPIO[48, 39] Core Input Input Defined Defined Off Off Interrupts PIRQ[A:D]#] Core High-Z High-Z Defined Defined Off Off PIRQ[H:E]# / GPIO[5:2] Core Input Input Defined Defined Off Off SERIRQ Core High-Z High-Z Running High-Z Off Off USB Interface USB[11:0][P,N] Suspend Low Low Low Low Low Low USBRBIAS Suspend High-Z High-Z Defined Defined Defined Defined Power Management 98 PLTRST# Suspend Low High High High Low Low SLP_M#9 Suspend Low High High High Low Defined SLP_S3# Suspend Low High High High Low Low SLP_S4# Suspend Low High High High High Defined S4_STATE# / GPIO26 Suspend Low Defined Defined Defined Defined Defined SLP_S5# Suspend Low High High High High Low8 CLKRUN# Core Low Low Running High-Z Off Off STP_CPU# Suspend High High Defined High Off Off STP_PCI# Suspend High High Defined High Low Low SUS_STAT# / LPCPD# Suspend Low High High High Low Low Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States Table 3-3. Power Plane and States for Output and I/O Signals for Mobile Configurations (Sheet 3 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 C3/C4/ C5/C6 S1 S3 S4/S5 DPRSLPVR Core Low Low Low/High High Off Off DPRSTP# CPU High High Low/High High Off Off SUSCLK Suspend Low CK_PWRGD Suspend Low PMSYNC# / GPIO0 Core Running Input High High High Low Low Input Defined/ Low12 Defined Off Off High Off Off Processor Interface A20M# CPU Dependant on A20GATE Signal CPUPWRGD CPU See Note 3 High High High Off Off IGNNE# CPU High See Note 1 High High Off Off INIT# CPU High High High High Off Off INTR CPU See Note 6 See Note 6 Defined Low Off Off See Note 1 Defined NMI CPU See Note 6 See Note 6 Defined Low Off Off SMI# CPU High High Defined High Off Off STPCLK# CPU High High Low Low Off Off DPSLP# CPU High High High/Low High Off Off Defined Defined Defined SMBus Interface SMBCLK, SMBDATA Suspend High-Z High-Z Defined System Management Interface MEM_LED / GPIO24 Suspend Low Low Defined Defined Defined Defined SUS_PWR_ACK (Digital Office Only) / GPIO10 Suspend Input Input Defined Defined Defined Defined Suspend Input Input Defined Defined Defined Defined WOL_EN / GPIO9 Suspend High-Z High-Z Defined Defined Defined Defined CLGPIO5 (Digital Office Only)/ GPIO57 Suspend Input Input Defined Defined Defined Defined SMLINK[1:0] Suspend High-Z High-Z Defined Defined Defined Defined LINKALERT# / GPIO60 / CLGPIO4 (Digital Office Only) Suspend High-Z High-Z Defined Defined Defined Defined AC_PRESENT (Digital Office Only)/ GPIO14 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 99 Intel® ICH9 Pin States Table 3-3. Power Plane and States for Output and I/O Signals for Mobile Configurations (Sheet 4 of 4) Signal Name Power Plane During Reset4 Immediately after Reset4 C3/C4/ C5/C6 S1 S3 S4/S5 Defined Off Off Miscellaneous Signals SPKR11 Core High-Z Low Defined Intel® High Definition Audio Interface HDA_RST# HDA Suspend Low Low7 High Defined Low Low HDA_SDOUT11 HDA High-Z Running Running Low Off Off 11 HDA_SYNC HDA High-Z Running Running Low Off Off HDA_BIT_CLK HDA High-Z Low7 Running Low Off Off HDA_DOCK_RST# / GPIO34 HDA Low Low7 Defined Defined Off Off HDA_DOCK_EN# / GPIO3311 HDA High High Defined Defined Off Off UnMultiplexed GPIO Signals GPIO8 Suspend Input Input Defined Defined Defined Defined GPIO12 Suspend Low Low Defined Defined Defined Defined GPIO13 Suspend Input Input Defined Defined Defined Defined 11 Core Low High Defined Defined Off Off GPIO4911 Core High High Defined Defined Off Off GPIO56 Suspend Input Input Defined Defined Defined Defined GPIO20 SPI Interface SPI_CS0# Controller Link High High Defined Defined Defined Defined SPI_CS1#11 Controller Link High High Defined Defined Defined Defined SPI_MOSI11 Controller Link Low Low Defined Defined Defined Defined SPI_CLK Controller Link Low Low Running Running Defined Defined Controller Link CL_CLK0, CL_DATA0 Controller Link Low Low Defined10 Defined10 Defined10 Defined10 CL_CLK1, CL_DATA1 Suspend Low Low Defined10 Defined10 Defined10 Defined10 CL_RST[1:0]# Suspend Low High Defined10 Defined10 Defined10 Defined10 NOTES: 1. ICH9 drives these signals High after the processor Reset 2. GPIO[18] will toggle at a frequency of approximately 1 Hz when the ICH9 comes out of reset 100 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 3.3 CPUPWRGD represents a logical AND of the ICH9’s VRMPWRGD and PWROK signals, and thus will be driven low by ICH9 when either VRMPWRGD or PWROK are inactive. The states of Core and processor signals are evaluated at the times During PLTRST# and Immediately after PLTRST#. The states of the LAN and GLAN signals are evaluated at the times During LAN_RST# and Immediately after LAN_RST#. The states of the Controller Link signals are evaluated at the times During CL_RST# and Immediately after CL_RST#. The states of the Suspend signals are evaluated at the times During RSMRST# and Immediately after RSMRST#. The states of the HDA signals are evaluated at the times During HDA_RST# and Immediately after HDA_RST#. ICH9 drives these signals Low before PWROK rising and Low after the processor Reset. SLP_S5# signals will be high in the S4 state. Low until Intel High Definition Audio Controller Reset bit set (D27:F0:Offset HDBAR+08h:bit 0), at which time HDA_RST# will be High and HDA_BIT_CLK will be Running. PETp/n[6:1] high until port is enabled by software. The SLP_M# state will be determined by Intel AMT policies. The state of these signals in S3-5 will be defined by Intel AMT Policies. This signal is sampled as a functional strap during reset. PMSYNC# is low during C5/C6 state only. Power Planes for Input Signals Table 3-4 and Table 3-5 shows the power plane associated with each input signal, as well as what device drives the signal at various times. Valid states include: High Low Static: Will be high or low, but will not change Driven: Will be high or low, and is allowed to change Running: For input clocks ICH9 suspend well signal states are indeterminate and undefined and may glitch prior to RSMRST# deassertion. This does not apply to LAN_RST#, SLP_S3#, SLP_S4#, S4_STATE# and SLP_S5#. These signals are determinate and defined prior to RSMRST# deassertion. ICH9 core well signal states are indeterminate and undefined and may glitch prior to PWROK assertion. This does not apply to FERR# and THRMTRIP#. These signals are determinate and defined prior to PWROK assertion. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 101 Intel® ICH9 Pin States Table 3-4. Power Plane for Input Signals for Desktop Configurations (Sheet 1 of 3) Signal Name Power Well Driver During Reset S1 S3 S4/S5 DMI DMI_CLKP, DMI_CLKN Core Clock Generator Running Off Off DMI[3:0]RXP, DMI[3:0]RXN Core (G)MCH Driven Off Off Driven Off Off PCI Express* PERp[5:1], PERn[5:1], PERp6 / GLAN_RXp, PERn6 / GLAN_RXn Core PCI Express* Device PCI Bus REQ0#, REQ1# / GPIO501 REQ2# / GPIO521 REQ3# / GPIO541 Core External Pull-up Driven Off Off PCICLK Core Clock Generator Running Off Off PME# Suspend Internal Pull-up Driven Driven Driven SERR# Core PCI Bus Peripherals High Off Off LPC Interface LDRQ0# Core LPC Devices High Off Off LDRQ1# / GPIO231 Core LPC Devices High Off Off LAN Connect Interface GLAN_CLK Suspend LAN Connect Component Driven Off Off LAN_RXD[2:0] Suspend LAN Connect Component Driven Driven Driven Driven Off Off Gigabit LAN Connect Interface GLAN_RXp / PER6p, GLAN_RXn / PER6n Suspend Gigabit Lan Connect Component SATA Interface 102 SATA_CLKP, SATA_CLKN Core Clock Generator Running Off Off SATA[5:0]RXP, SATA[5:0]RXN Core SATA Drive Driven Off Off SATARBIAS# Core External Pull-down Driven Off Off Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States Table 3-4. Power Plane for Input Signals for Desktop Configurations (Sheet 2 of 3) Signal Name Power Well Driver During Reset S1 S3 S4/S5 SATA[5:4]GP SATA[3:0]GP / GPIO[37, 36, 19, 21]1 Core External Device or External Pull-up/Pull-down Driven Off Off USB Interface OC0# / GPIO59, OC[4:1]# / GPIO[43:40], OC[7:5]# / GPIO [31:29], OC[11:8]# / GPIO[47:44] Suspend External Pull-ups Driven Driven Driven USBRBIAS# Suspend External Pull-down Driven Driven Driven Driven Driven Driven Power Management CLPWROK Suspend External Circuit LAN_RST# Suspend External Circuit High High High MCH_SYNC# Core (G)MCH Driven Off Off PWRBTN# Suspend Internal Pull-up Driven Driven Driven PWROK RTC System Power Supply Driven Off Off RI# Suspend Serial Port Buffer Driven Driven Driven RSMRST# RTC External RC Circuit High High High SYS_RESET# Suspend External Circuit Driven Driven Driven THRM# Core Thermal Sensor Driven Off Off THRMTRIP# CPU Thermal Sensor Driven Off Off VRMPWRGD Suspend Processor Voltage Regulator High Low Low WAKE# Suspend External Pull-up Driven Driven Driven Processor Interface A20GATE Core External Microcontroller Static Off Off FERR# Core Processor Static Off Off RCIN# Core External Microcontroller High Off Off Driven Driven Driven Driven High High SMBus Interface SMBALERT# / GPIO111 Suspend External Pull-up System Management Interface INTRUDER# RTC External Switch Miscellaneous Signals INTVRMEN RTC External Pull-up High High High LAN100_SLP RTC External Pull-up High High High Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 103 Intel® ICH9 Pin States Table 3-4. Power Plane for Input Signals for Desktop Configurations (Sheet 3 of 3) Signal Name Power Well Driver During Reset S1 S3 S4/S5 RTCRST# RTC External RC Circuit High High High SRTCRST# RTC External RC Circuit High High High CL_VREF0 Controller Link External Circuit Driven Driven Driven TP0 Suspend External Pull-up High High High Low Low Low Driven Driven Driven Driven Off Off Intel® High Definition Audio Interface HDA_SDIN[3:0] Suspend Intel High Definition Audio Codec SPI Interface SPI_MISO Suspend Internal Pull-up Intel® TACH[3:0]/ GPIO[7,6,1,17]1 Core Quiet System Technology External Pull-up Clocks CLK14 Core Clock Generator Running Off Off CLK48 Core Clock Generator Running Off Off NOTES: 1. These signals can be configured as outputs in GPIO mode. Table 3-5. Power Plane for Input Signals for Mobile Configurations (Sheet 1 of 3) Signal Name Power Well Driver During Reset C3/C4/ C5/C6 S1 S3 S4/S5 DMI DMI_CLKP DMI_CLKN DMI[3:0]RXP, DMI[3:0]RXN Core Clock Generator Running Running Off Off Core (G)MCH Driven Driven Off Off Driven Driven Off Off PCI Express PERp[6:1], PERn[6:1] Core PCI Express* Device PCI Bus PCICLK Core Clock Generator Running Running Off Off PME# Suspend Internal Pull-up Driven Driven Driven Driven REQ0#, REQ1/GPIO501 REQ2/GPIO521 REQ3/GPIO541 Core External Pull-up Driven Driven Off Off SERR# Core PCI Bus Peripherals Driven High Off Off LPC Interface 104 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 Pin States Table 3-5. Power Plane for Input Signals for Mobile Configurations (Sheet 2 of 3) Signal Name Power Well Driver During Reset C3/C4/ C5/C6 S1 S3 S4/S5 LDRQ0# Core LPC Devices Driven High Off Off LDRQ1# / GPIO231 Core LPC Devices Driven High Off Off Platform LAN Connect Interface GLAN_CLK LAN LAN Connect Component Driven Driven Off Off LAN_RXD[2:0] LAN LAN Connect Component Driven Driven Driven Driven Driven Driven Off Off Gigabit LAN Connect Interface GLAN_RXp GLAN_RXn GLAN Gigabit Lan Connect Component SATA Interface SATA_CLKP, SATA_CLKN Core Clock Generator Running Running Off Off SATA[5:4, 1:0]RXP, SATA[5:4, 1:0]RXN Core SATA Drive Driven Driven Off Off SATARBIAS# Core External Pull-Down Driven Driven Off Off Core External Device or External Pull-up/Pulldown Driven Driven Off Off SATA[5:4, 1:0]GP / GPIO[37, 36, 19, 21]1 USB Interface OC0# / GPIO59, OC[7:5]# / GPIO[31:29], OC[4:1]# / GPIO[43:40], OC[11:8]# / GPIO[47:44] Suspend External Pull-ups Driven Driven Driven Driven USBRBIAS# Suspend External Pull-down Driven Driven Driven Driven Power Management CLPWROK Suspend External Circuit Driven Driven Driven Driven LAN_RST# Suspend Power Supply High High Static Static MCH_SYNC# Core (G)MCH Driven Driven Off Off PWRBTN# Suspend Internal Pull-up Driven Driven Driven Driven PWROK RTC System Power Supply Driven Driven Off Off RI# Suspend Serial Port Buffer Driven Driven Driven Driven RSMRST# RTC External RC Circuit High High High High SYS_RESET# Suspend External Circuit Driven Driven Driven Driven THRM# Core Thermal Sensor Driven Driven Off Off THRMTRIP# CPU Thermal Sensor Driven Driven Off Off VRMPWRGD Suspend Processor Voltage Regulator Driven Driven Low Low WAKE# Suspend External Pull-up Driven Driven Driven Driven Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 105 Intel® ICH9 Pin States Table 3-5. Power Plane for Input Signals for Mobile Configurations (Sheet 3 of 3) Signal Name Power Well Driver During Reset C3/C4/ C5/C6 S1 S3 S4/S5 BATLOW# Suspend Power Supply High High High High Processor Interface A20GATE Core External Microcontroller Static Static Off Off FERR# Core Processor Static Static Off Off Core External Microcontroller High High Off Off Driven Driven Driven Driven Driven Driven High High High High High High RCIN# SMBus Interface SMBALERT# / GPIO111 Suspend External Pull-up System Management Interface INTRUDER# RTC External Switch INTVRMEN RTC LAN100_SLP RTC External Pull-up High High High High RTCRST# RTC External RC Circuit High High High High SRTCRST# RTC External RC Circuit High High High High TP0 Suspend External Pull-up High High High High CL_VREF0 Controller Link External Circuit Driven Driven Driven Driven CL_VREF1 Suspend External Circuit Driven Driven Driven Driven Driven Low Low Low Driven Driven Driven Driven Miscellaneous Signals External Pull-up Intel® High Definition Audio Interface HDA_SDIN[3:0] Suspend Intel High Definition Audio Codec SPI Interface SPI_MISO Suspend Internal Pull-up Clocks CLK14 Core Clock Generator Running Running Off Off CLK48 Core Clock Generator Running Running Off Off NOTE: 1. These signals can be configured as outputs in GPIO mode. 2. The state of the DPRSLPVR and DPRSTP# signals in C4 are high if Deeper Sleep is enabled or low if it is disabled. §§ 106 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Intel® ICH9 and System Clock Domains 4 Intel® ICH9 and System Clock Domains Table 4-1 shows the system clock domains. Figure 4-1 and Figure 4-2 shows the assumed connection of the various system components, including the clock generator in both desktop and mobile systems. For complete details of the system clocking solution, refer to the system’s clock generator component specification. Table 4-1. Intel® ICH9 and System Clock Domains Clock Domain Frequency Source ICH9 SATA_CLKP, SATA_CLKN 100 MHz Main Clock Generator Differential clock pair used for SATA. ICH9 DMI_CLKP, DMI_CLKN 100 MHz Main Clock Generator Differential clock pair used for DMI. Usage ICH9 PCICLK 33 MHz Main Clock Generator Free-running PCI Clock to Intel® ICH9. This clock remains on during S0 and S1 (in desktop) state, and is expected to be shut off during S3 or below in desktop configurations or S1 or below in mobile configurations. System PCI 33 MHz Main Clock Generator PCI Bus, LPC I/F. These only go to external PCI and LPC devices. Will stop based on CLKRUN# (and STP_PCI#) in mobile configurations. ICH9 CLK48 48.000 MHz Main Clock Generator Super I/O, USB controllers. Expected to be shut off during S3 or below in desktop configurations or S1 or below in mobile configurations. ICH9 CLK14 14.31818 MHz Main Clock Generator Used for ACPI timer and HPET. Expected to be shut off during S3 or below in desktop configurations or S1 or below in mobile configurations. GLAN_CLK 5 to 62.5 MHz LAN Connect Component Generated by the LAN Connect component. Expected to be shut off during S3 or below in desktop configurations or S1 or below in mobile configurations. SPI_CLK 17.86 MHz/ 31.25 MHz ICH Generated by the ICH. Expected to be shut off during S3 or below in desktop configurations or S1 or below in mobile configurations. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 107 Intel® ICH9 and System Clock Domains Figure 4-1. Desktop Conceptual System Clock Diagram 33 MHz 14.31818 MHz 48.000 MHz PCI Clocks (33 MHz) Clock Gen. 14.31818 MHz 48 MHz ® Intel ICH9 SATA 100 MHz Diff. Pair DMI 100 MHz Diff. Pair 100 MHz Diff. Pair PCI Express 100 MHz Diff. Pairs 1 to 6 Differential Clock Fan Out Device 62.5 MHz LAN Connect 24 MHz HD Audio Codec(s) 32 kHz XTAL SUSCLK# (32 kHz) Figure 4-2. Mobile Conceptual Clock Diagram 33 MHz 14.31818 MHz 48.000 MHz PCI Clocks (33 MHz) Clock Gen. STP_CPU# ® Intel ICH9M STP_PCI# SATA 100 MHz Diff. Pair 14.31818 MHz 48 MHz DMI 100 MHz Diff. Pair 100 MHz Diff. Pair 1 to 6 Differential Clock Fan Out Device 62.5 MHz LAN Connect 24 MHz HD Audio Codec(s) PCI Express 100 MHz Diff. Pairs 32 kHz XTAL SUSCLK# (32 kHz) §§ 108 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5 Functional Description This chapter describes the functions and interfaces of the Intel® ICH9 family. 5.1 DMI-to-PCI Bridge (D30:F0) The DMI-to-PCI bridge resides in PCI Device 30, Function 0 on bus #0. This portion of the ICH9 implements the buffering and control logic between PCI and Direct Media Interface (DMI). The arbitration for the PCI bus is handled by this PCI device. The PCI decoder in this device must decode the ranges for the DMI. All register contents are lost when core well power is removed. Direct Media Interface (DMI) is the chip-to-chip connection between the Memory Controller Hub / Graphics and Memory Controller Hub ((G)MCH) and I/O Controller Hub 9 (ICH9). This high-speed interface integrates advanced priority-based servicing allowing for concurrent traffic and true isochronous transfer capabilities. Base functionality is completely software transparent permitting current and legacy software to operate normally. In order to provide for true isochronous transfers and configurable Quality of Service (QoS) transactions, the ICH9 supports two virtual channels on DMI: VC0 and VC1. These two channels provide a fixed arbitration scheme where VC1 is always the highest priority. VC0 is the default conduit of traffic for DMI and is always enabled. VC1 must be specifically enabled and configured at both ends of the DMI link (i.e., the ICH9 and (G)MCH). Configuration registers for DMI, virtual channel support, and DMI active state power management (ASPM) are in the RCRB space in the Chipset Config Registers (Chapter 10). DMI is also capable of operating in an Enterprise Southbridge Interface (ESI) compatible mode. ESI is a chip-to-chip connection for server chipsets. In this ESIcompatible mode, the DMI signals require AC coupling. A hardware strap is used to configure DMI in ESI-compatible mode, see Section 2.24 for details. 5.1.1 PCI Bus Interface The ICH9 PCI interface supports PCI Local Bus Specification, Revision 2.3, at 33 MHz. The ICH9 integrates a PCI arbiter that supports up to four external PCI bus masters in addition to the internal ICH9 requests. 5.1.2 PCI Bridge As an Initiator The bridge initiates cycles on the PCI bus when granted by the PCI arbiter. The bridge generates the following cycle types: Table 5-1. PCI Bridge Initiator Cycle Types Command C/BE# Notes I/O Read/Write 2h/3h Non-posted Memory Read/Write 6h/7h Writes are posted Configuration Read/Write Ah/Bh Non-posted Special Cycles 1h Posted Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 109 Functional Description 5.1.2.1 Memory Reads and Writes The bridge bursts memory writes on PCI that are received as a single packet from DMI. 5.1.2.2 I/O Reads and Writes The bridge generates single DW I/O read and write cycles. When the cycle completes on the PCI bus, the bridge generates a corresponding completion on DMI. If the cycle is retried, the cycle is kept in the down bound queue and may be passed by a postable cycle. 5.1.2.3 Configuration Reads and Writes The bridge generates single DW configuration read and write cycles. When the cycle completes on the PCI bus, the bridge generates a corresponding completion. If the cycle is retried, the cycle is kept in the down bound queue and may be passed by a postable cycle. 5.1.2.4 Locked Cycles The bridge propagates locks from DMI per the PCI Local Bus Specification. The PCI bridge implements bus lock, which means the arbiter will not grant to any agent except DMI while locked. If a locked read results in a target or master abort, the lock is not established (as per the PCI Local Bus Specification). Agents north of the ICH9 must not forward a subsequent locked read to the bridge if they see the first one finish with a failed completion. 5.1.2.5 Target / Master Aborts When a cycle initiated by the bridge is master/target aborted, the bridge will not reattempt the same cycle. For multiple DW cycles, the bridge increments the address and attempts the next DW of the transaction. For all non-postable cycles, a target abort response packet is returned for each DW that was master or target aborted on PCI. The bridge drops posted writes that abort. 5.1.2.6 Secondary Master Latency Timer The bridge implements a Master Latency Timer via the SMLT register which, upon expiration, causes the de-assertion of FRAME# at the next valid clock edge when there is another active request to use the PCI bus. 5.1.2.7 Dual Address Cycle (DAC) The bridge will issue full 64-bit dual address cycles for device memory-mapped registers above 4 GB. 110 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.1.2.8 Memory and I/O Decode to PCI The PCI bridge in the ICH9 is a subtractive decode agent, which follows the following rules when forwarding a cycle from DMI to the PCI interface: • The PCI bridge will positively decode any memory/IO address within its window registers, assuming PCICMD.MSE (D30:F0:Offset 04h:bit 1) is set for memory windows and PCICMD.IOSE (D30:F0:Offset 04h:bit 0) is set for IO windows. • The PCI bridge will subtractively decode any 64-bit memory address not claimed by another agent, assuming PCICMD.MSE (D30:F0:Offset 04h:bit 1) is set. • The PCI bridge will subtractively decode any 16-bit I/O address not claimed by another agent assuming PCICMD.IOSE (D30:F0:Offset 04h:bit 0) is set. • If BCTRL.IE (D30:F0:Offset 3Eh:bit 2) is set, the PCI bridge will not positively forward from primary to secondary called out ranges in the IO window per PCI Local Bus Specification (I/O transactions addressing the last 768 bytes in each, 1 KB block: offsets 100h to 3FFh). The PCI bridge will still take them subtractively assuming the above rules. • If BCTRL.VGAE (D30:F0:Offset 3Eh:bit 3) is set, the PCI bridge will positively forward from primary to secondary I/O and memory ranges as called out in the PCI Bridge Specification, assuming the above rules are met. 5.1.3 Parity Error Detection and Generation PCI parity errors can be detected and reported. The following behavioral rules apply: • When a parity error is detected on PCI, the bridge sets the SECSTS.DPE (D30:F0:Offset 1Eh:bit 15). • If the bridge is a master and BCTRL.PERE (D30:F0:Offset 3Eh:bit 0) is set and one of the parity errors defined below is detected on PCI, then the bridge will set SECSTS.DPD (D30:F0:Offset 1Eh:bit 8) and will also generate an internal SERR#. — During a write cycle, the PERR# signal is active, or — A data parity error is detected while performing a read cycle • If an address or command parity error is detected on PCI and PCICMD.SEE (D30:F0:Offset 04h:bit 8), BCTRL.PERE, and BCTRL.SEE (D30:F0:Offset 3Eh:bit 1) are all set, the bridge will set PSTS.SSE (D30:F0:Offset 06h:bit 14) and generate an internal SERR#. • If the PSTS.SSE is set because of an address parity error and the PCICMD.SEE is set, the bridge will generate an internal SERR# • When bad parity is detected from DMI, bad parity will be driven on all data from the bridge. • When an address parity error is detected on PCI, the PCI bridge will never claim the cycle. This is a slight deviation from the PCI bridge spec, which says that a cycle should be claimed if BCTRL.PERE is not set. However, DMI does not have a concept of address parity error, so claiming the cycle could result in the rest of the system seeing a bad transaction as a good transaction. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 111 Functional Description 5.1.4 PCIRST# The PCIRST# pin is generated under two conditions: • PLTRST# active • BCTRL.SBR (D30:F0:Offset 3Eh:bit 6) set to 1 The PCIRST# pin is in the suspend well. PCIRST# should be tied to PCI bus agents, but not other agents in the system. 5.1.5 Peer Cycles The PCI bridge may be the initiator of peer cycles. Peer cycles include memory, IO, and configuration cycle types. Peer cycles are only allowed through VC0, and are enabled with the following bits: • BPC.PDE (D30:F0:Offset 4Ch:bit 2) – Memory and IO cycles • BPC.CDE (D30:F0:Offset 4Ch:bit 1) – Configuration cycles When enabled for peer for one of the above cycle types, the PCI bridge will perform a peer decode to see if a peer agent can receive the cycle. When not enabled, memory cycles (posted and/or non-posted) are sent to DMI, and I/O and/or configuration cycles are not claimed. Configuration cycles have special considerations. Under the PCI Local Bus Specification, these cycles are not allowed to be forwarded upstream through a bridge. However, to enable things such as manageability, BPC.CDE can be set. When set, type 1 cycles are allowed into the part. The address format of the type 1 cycle is slightly different from a standard PCI configuration cycle to allow addressing of extended PCI space. The format is as follows: Table 5-2. Type 1 Address Format Bits Definition 31:27 Reserved (same as the PCI Local Bus Specification) 26:24 Extended Configuration Address – allows addressing of up to 4K. These bits are combined with bits 7:2 to get the full register. 23:16 Bus Number (same as the PCI Local Bus Specification) 15:11 Device Number (same as the PCI Local Bus Specification) 10:8 Function Number (same as the PCI Local Bus Specification) 7:2 Register (same as the PCI Local Bus Specification) 1 0 0 Must be 1 to indicate a type 1 cycle. Type 0 cycles are not decoded. Note: The ICH9’s USB controllers cannot perform peer-to-peer traffic. 5.1.6 PCI-to-PCI Bridge Model From a software perspective, the ICH9 contains a PCI-to-PCI bridge. This bridge connects DMI to the PCI bus. By using the PCI-to-PCI bridge software model, the ICH9 can have its decode ranges programmed by existing plug-and-play software such that PCI ranges do not conflict with graphics aperture ranges in the Host controller. 112 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.1.7 IDSEL to Device Number Mapping When addressing devices on the external PCI bus (with the PCI slots), the ICH9 asserts one address signal as an IDSEL. When accessing device 0, the ICH9 asserts AD16. When accessing Device 1, the ICH9 asserts AD17. This mapping continues all the way up to device 15 where the ICH9 asserts AD31. Note that the ICH9’s internal functions (Intel® High Definition Audio, USB, SATA and PCI Bridge) are enumerated like they are off of a separate PCI bus (DMI) from the external PCI bus. 5.1.8 Standard PCI Bus Configuration Mechanism The PCI Bus defines a slot based “configuration space” that allows each device to contain up to eight functions with each function containing up to 256, 8-bit configuration registers. The PCI Local Bus Specification, Revision 2.3 defines two bus cycles to access the PCI configuration space: Configuration Read and Configuration Write. Memory and I/O spaces are supported directly by the processor. Configuration space is supported by a mapping mechanism implemented within the ICH9. The PCI Local Bus Specification, Revision 2.3 defines two mechanisms to access configuration space, Mechanism 1 and Mechanism 2. The ICH9 only supports Mechanism 1. Warning: Configuration writes to internal devices, when the devices are disabled, are invalid and may cause undefined results. 5.2 PCI Express* Root Ports (D28:F0,F1,F2,F3,F4,F5) There are six root ports available in ICH9. These all reside in device 28, and take function 0 – 5. Port 1 is function 0, port 2 is function 1, port 3 is function 2, port 4 is function 3, port 5 is function 4, and port 6 is function 5. PCI Express Root Ports 1-4 can be statically configured as four x1 Ports or ganged together to form one x4 port. Ports 5 and 6 can only be used as two x1 ports. On Mobile platforms, PCI Express Ports 1-4 can also be configured as one x2 port (using ports 1 and 2) with ports 3 and 4 configured as x1 ports. The port configuration is set by RCBA 224h [Bits 1:0] see Section 10.1.38 for more details. 5.2.1 Interrupt Generation The root port generates interrupts on behalf of Hot-Plug and power management events, when enabled. These interrupts can either be pin based, or can be MSIs, when enabled. When an interrupt is generated via the legacy pin, the pin is internally routed to the ICH9 interrupt controllers. The pin that is driven is based upon the setting of the chipset configuration registers. Specifically, the chipset configuration registers used are the D28IP (Base address + 310Ch) and D28IR (Base address + 3146h) registers. The following table summarizes interrupt behavior for MSI and wire-modes. In the table “bits” refers to the Hot-Plug and PME interrupt bits. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 113 Functional Description Table 5-3. MSI vs. PCI IRQ Actions Wire-Mode Action Interrupt Register MSI Action All bits 0 Wire inactive No action One or more bits set to 1 Wire active Send message One or more bits set to 1, new bit gets set to 1 Wire active Send message One or more bits set to 1, software clears some (but not all) bits Wire active Send message One or more bits set to 1, software clears all bits Wire inactive No action Software clears one or more bits, and one or more bits are set on the same clock Wire active Send message 5.2.2 Power Management 5.2.2.1 S3/S4/S5 Support Software initiates the transition to S3/S4/S5 by performing an IO write to the Power Management Control register in the ICH9. After the IO write completion has been returned to the processor, each root port will send a PME_Turn_Off TLP (Transaction Layer Packet) message on its downstream link. The device attached to the link will eventually respond with a PME_TO_Ack TLP message followed by sending a PM_Enter_L23 DLLP (Data Link Layer Packet) request to enter the L2/L3 Ready state. When all of the ICH9 root ports links are in the L2/L3 Ready state, the ICH9 power management control logic will proceed with the entry into S3/S4/S5. Prior to entering S3, software is required to put each device into D3HOT. When a device is put into D3HOT it will initiate entry into a L1 link state by sending a PM_Enter_L1 DLLP. Thus under normal operating conditions when the root ports sends the PME_Turn_Off message the link will be in state L1. However, when the root port is instructed to send the PME_Turn_Off message, it will send it whether or not the link was in L1. Endpoints attached to ICH can make no assumptions about the state of the link prior to receiving a PME_Turn_Off message. 5.2.2.2 Resuming from Suspended State The root port contains enough circuitry in the suspend well to detect a wake event through the WAKE# signal and to wake the system. When WAKE# is detected asserted, an internal signal is sent to the power management controller of the ICH9 to cause the system to wake up. This internal message is not logged in any register, nor is an interrupt/GPE generated due to it. 5.2.2.3 Device Initiated PM_PME Message When the system has returned to a working state from a previous low power state, a device requesting service will send a PM_PME message continuously, until acknowledge by the root port. The root port will take different actions depending upon whether this is the first PM_PME has been received, or whether a previous message has been received but not yet serviced by the operating system. If this is the first message received (RSTS.PS - D28:F0/F1/F2/F3/F4/F5:Offset 60h:bit 16 is cleared), the root port will set RSTS.PS, and log the PME Requester ID into RSTS.RID (D28:F0/F1/F2/F3/F4/F5:Offset 60h:bits 15:0). If an interrupt is enabled via 114 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description RCTL.PIE (D28:F0/F1/F2/F3/F4/F5:Offset 5Ch:bit 3), an interrupt will be generated. This interrupt can be either a pin or an MSI if MSI is enabled via MC.MSIE (D28:F0/F1/ F2/F3/F4/F5:Offset 82h:bit 0). See Section 5.2.2.4 for SMI/SCI generation. If this is a subsequent message received (RSTS.PS is already set), the root port will set RSTS.PP (D28:F0/F1/F2/F3/F4/F5:Offset 60h:bit 17) and log the PME Requester ID from the message in a hidden register. No other action will be taken. When the first PME event is cleared by software clearing RSTS.PS, the root port will set RSTS.PS, clear RSTS.PP, and move the requester ID from the hidden register into RSTS.RID. If RCTL.PIE is set, an interrupt will be generated. If RCTL.PIE is not set, a message will be sent to the power management controller so that a GPE can be set. If messages have been logged (RSTS.PS is set), and RCTL.PIE is later written from a 0 to a 1, and interrupt will be generated. This last condition handles the case where the message was received prior to the operating system re-enabling interrupts after resuming from a low power state. 5.2.2.4 SMI/SCI Generation Interrupts for power management events are not supported on legacy operating systems. To support power management on non-PCI Express aware operating systems, PM events can be routed to generate SCI. To generate SCI, MPC.PMCE must be set. When set, a power management event will cause SMSCS.PMCS (D28:F0/F1/F2/F3/F4/ F5:Offset DCh:bit 31) to be set. Additionally, BIOS workarounds for power management can be supported by setting MPC.PMME (D28:F0/F1/F2/F3/F4/F5:Offset D8h:bit 0). When this bit is set, power management events will set SMSCS.PMMS (D28:F0/F1/F2/F3/F4/F5:Offset DCh:bit 0), and SMI # will be generated. This bit will be set regardless of whether interrupts or SCI is enabled. The SMI# may occur concurrently with an interrupt or SCI. 5.2.3 SERR# Generation SERR# may be generated via two paths – through PCI mechanisms involving bits in the PCI header, or through PCI Express* mechanisms involving bits in the PCI Express capability structure. Figure 5-1. Generation of SERR# to Platform Secondary Parity Error PCI PSTS.SSE Primary Parity Error Secondary SERR# PCICMD.SEE SERR# Correctable SERR# Fatal SERR# PCI Express Non-Fatal SERR# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 115 Functional Description 5.2.4 Hot-Plug Each root port implements a Hot-Plug controller which performs the following: • Messages to turn on / off / blink LEDs • Presence and attention button detection • Interrupt generation The root port only allows Hot-Plug with modules (e.g., ExpressCard*). Edge-connector based Hot-Plug is not supported. 5.2.4.1 Presence Detection When a module is plugged in and power is supplied, the physical layer will detect the presence of the device, and the root port sets SLSTS.PDS (D28:F0/F1/F2/F3/F4/ F5:Offset 5Ah:bit 6) and SLSTS.PDC (D28:F0/F1/F2/F3:Offset 6h:bit 3). If SLCTL.PDE (D28:F0/F1/F2/F3F4/F5:Offset 58h:bit 3) and SLCTL.HPE (D28:F0/F1/F2/F3F4/ F5:Offset 58h:bit 5) are both set, the root port will also generate an interrupt. When a module is removed (via the physical layer detection), the root port clears SLSTS.PDS and sets SLSTS.PDC. If SLCTL.PDE and SLCTL.HPE are both set, the root port will also generate an interrupt. 5.2.4.2 Message Generation When system software writes to SLCTL.AIC (D28:F0/F1/F2/F3F4/F5:Offset 58h:bits 7:6) or SLCTL.PIC (D28:F0/F1/F2/F3F4/F5:Offset 58h:bits 9:8), the root port will send a message down the link to change the state of LEDs on the module. Writes to these fields are non-postable cycles, and the resulting message is a postable cycle. When receiving one of these writes, the root port performs the following: • Changes the state in the register. • Generates a completion into the upstream queue • Formulates a message for the downstream port if the field is written to regardless of if the field changed. • Generates the message on the downstream port • When the last message of a command is transmitted, sets SLSTS.CCE (D28:F0/F1/ F2/F3F4/F5:Offset 58h:bit 4) to indicate the command has completed. If SLCTL.CCE and SLCTL.HPE (D28:F0/F1/F2/F3F4/F5:Offset 58h:bit 5) are set, the root port generates an interrupt. The command completed register (SLSTS.CC) applies only to commands issued by software to control the Attention Indicator (SLCTL.AIC), Power Indicator (SLCTL.PIC), or Power Controller (SLCTL.PCC). However, writes to other parts of the Slot Control Register would invariably end up writing to the indicators, power controller fields; Hence, any write to the Slot Control Register is considered a command and if enabled, will result in a command complete interrupt. The only exception to this rule is a write to disable the command complete interrupt which will not result in a command complete interrupt. A single write to the Slot Control register is considered to be a single command, and hence receives a single command complete, even if the write affects more than one field in the Slot Control Register. 116 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.2.4.3 Attention Button Detection When an attached device is ejected, an attention button could be pressed by the user. This attention button press will result in the PCI Express message “Attention_Button_Pressed” from the device. Upon receiving this message, the root port will set SLSTS.ABP (D28:F0/F1/F2/F3F4/F5:Offset 5Ah:bit 0). If SLCTL.ABE (D28:F0/F1/F2/F3F4/F5:Offset 58h:bit 0) and SLCTL.HPE (D28:F0/F1/F2/ F3F4/F5:Offset 58h:bit 5) are set, the Hot-Plug controller will also generate an interrupt. The interrupt is generated on an edge-event. For example, if SLSTS.ABP is already set, a new interrupt will not be generated. 5.2.4.4 SMI/SCI Generation Interrupts for Hot-Plug events are not supported on legacy operating systems. To support Hot-Plug on non-PCI Express aware operating systems, Hot-Plug events can be routed to generate SCI. To generate SCI, MPC.HPCE (D28:F0/F1/F2/F3F4/F5:Offset D8h:bit 30) must be set. When set, enabled Hot-Plug events will cause SMSCS.HPCS (D28:F0/F1/F2/F3F4/F5:Offset DCh:bit 30) to be set. Additionally, BIOS workarounds for Hot-Plug can be supported by setting MPC.HPME (D28:F0/F1/F2/F3F4/F5:Offset D8h:bit 1). When this bit is set, Hot-Plug events can cause SMI status bits in SMSCS to be set. Supported Hot-Plug events and their corresponding SMSCS bit are: • Command Completed - SCSCS.HPCCM (D28:F0/F1/F2/F3/F4/F5:Offset DCh:bit 3) • Presence Detect Changed - SMSCS.HPPDM (D28:F0/F1/F2/F3/F4/F5:Offset DCh:bit 1) • Attention Button Pressed - SMSCS.HPABM (D28:F0/F1/F2/F3/F4/F5:Offset DCh:bit 2) • Link Active State Changed - SMSCS.HPLAS (D28:F0/F1/F2/F3/F4/F5:Offset DCh:bit 4) When any of these bits are set, SMI # will be generated. These bits are set regardless of whether interrupts or SCI is enabled for Hot-Plug events. The SMI# may occur concurrently with an interrupt or SCI. 5.3 Gigabit Ethernet Controller (B0:D25:F0) The ICH9 integrates a Gigabit Ethernet Controller. The integrated Gigabit Ethernet controller is compatible with Intel 10/100 PHY (Intel® 82562V Platform LAN Connect device) and Gigabit Ethernet PHY (Intel® 82566 Gigabit Platform LAN Connect device). The integrated Gigabit Ethernet controller provides two interfaces: LAN Connect Interface (LCI) for 10/100 operation and Gigabit LAN Connect Interface (GLCI) for Gigabit Ethernet operation. The GLCI is shared with the ICH9’s PCI Express port 6. The ICH9 integrated Gigabit Ethernet controller supports multi speed operation, 10/100/1000 MB/s. The integrated Gigabit Ethernet can operate in full-duplex at all supported speeds or half-duplex at 10/100 MB/s, and adheres with the IEEE 802.3x Flow Control Specification. Note: Gigabit Ethernet (1000Mb/s) is only supported in S0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 117 Functional Description The controller provides a system interface via a PCI function. A full memory-mapped or IO-mapped interface is provided to the software, along with DMA mechanisms for high performance data transfer. The following summarizes the ICH9 integrated Gigabit Ethernet controller features: • Configurable LED operation for customization of LED display. • IPv4 and IPv6 Checksum Offload support (receive, transmit, and large send). • 64-bit address master support for system using more than 4 GB of physical memory. • Configurable receive and transmit data FIFO, programmable in 1 KB increments. • Intelligent interrupt generation to enhance driver performance. • Compliance with Advanced Configuration and Power Interface and PCI Power Management standards. • ACPI register set and power down functionality supporting D0 & D3 states. • Full wake-up support (APM and ACPI). • Magic Packet wake-up enable with unique MAC address. • Fragmented UDP checksum off load for package reassembly. • Jumbo frames supported. 5.3.1 Gigabit Ethernet PCI Bus Interface The Gigabit Ethernet controller has a PCI interface to the host processor and host memory. The following sections detail the transaction on the bus. 5.3.1.1 Transaction Layer The upper layer of the host architecture is the transaction layer. The transaction layer connects to the device core using an implementation specific protocol. Through this core-to-transaction-layer protocol, the application-specific parts of the device interact with the subsystem and transmit and receive requests to or from the remote agent, respectively. 5.3.1.2 Data Alignment 5.3.1.2.1 4 K Boundary PCI requests must never specify an Address/Length combination that causes a Memory Space access to cross a 4 K boundary. It is the HW responsibility to break requests into 4 K-aligned requests (if needed). This does not pose any requirement on SW. However, if SW allocates a buffer across a 4 K boundary, HW will issue multiple requests for the buffer. SW should consider aligning buffers to 4 KB boundary in cases where it improves performance. The alignment to the 4 K boundaries is done in the core. The Transaction layer will not do any alignment according to these boundaries. 5.3.1.2.2 64 Bytes PCI requests are multiples of 64 bytes and aligned to make better use of memory controller resources. Writes, however, can be on any boundary and can cross a 64 byte alignment boundary 118 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.3.1.3 Configuration Request Retry Status The LAN Controller might have a delay in initialization due to NVM read. If the NVM configuration read operation is not completed and the device receives a Configuration Request, the device will respond with a Configuration Request Retry Completion Status to terminate the Request, and thus effectively stall the Configuration Request until such time that the subsystem has completed local initialization and is ready to communicate with the host. 5.3.2 Error Events and Error Reporting 5.3.2.1 Data Parity Error The PCI Host bus does not provide parity protection, but it does forward parity errors from bridges. The LAN Controller recognizes parity errors through the internal bus interface and will set the Parity Error bit in PCI Configuration space. If parity errors are enabled in configuration space, a system error will be indicated on the PCI Host bus to the chipset. The offending cycle with a parity error will be dropped and not processed by the LAN Controller. 5.3.2.2 Completion with Unsuccessful Completion Status A completion with unsuccessful completion status (any status other than "000") will be dropped and not processed by the LAN Controller. Furthermore, the request that corresponds to the unsuccessful completion will not be retried. When this unsuccessful completion status is received, the System Error bit in the PCI Configuration space will be set. If the system errors are enabled in configuration space, a system error will be indicated on the PCI Host bus to the chipset. 5.3.3 Ethernet Interface The integrated LAN controller provides a complete CSMA/CD function supporting IEEE 802.3 (10Mb/s), 802.3u (100Mb/s) implementations. It also supports the IEEE 802.3z and 802.3ab (1000Mb/s) implementations. The device performs all of the functions required for transmission, reception and collision handling called out in the standards. The mode used to communicate between the LAN controller and the LAN connect device supports 10/100/1000 Mbps operation, with both half- and full-duplex operation at 10/100 Mbps, and full-duplex operation at 1000 Mbps. 5.3.3.1 MAC/LAN Connect Interface The integrated LAN controller and LAN Connect Device communicate through either the platform LAN connect interface (LCI) or Gigabit LAN connect interface (GLCI). All controller configuration is performed using device control registers mapped into system memory or I/O space. The LAN Connect Device is configured via the LCI or Gigabit Ethernet Lan connect interface. The integrated MAC supports various modes as summarized in the following table Table 5-4. LAN Mode Support Mode Interface Active Connections Legacy 10/100 LCI 82562 Normal 10/100/1000 LCI, GLCI 82566 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 119 Functional Description 5.3.4 PCI Power Management The LAN Controller supports the Advanced Configuration and Power Interface (ACPI) specification as well as Advanced Power Management (APM). This allows the host to be awoken (i.e. from Sx (S3-S5) to S0) by network-related activity via an internal host wake signal. The LAN controller contains power management registers for PCI, and supports D0 and D3 states. PCI transactions are only allowed in the D0 state, except for host accesses to the LAN controller’s PCI configuration registers. 5.3.4.1 Wake-Up The LAN Controller supports two types of wakeup mechanisms: 1. Advanced Power Management (APM) Wakeup 2. ACPI Power Management Wakeup Both mechanisms use an internal WAKE# signal to wake the system up. This signal is connected to the suspend wake logic in the ICH9. The wake-up steps are as follows: 1. Host Wake Event occurs (note that packet is not delivered to host) 2. PME_STATUS bit is set 3. Internal WAKE# signal asserted by Host LAN function 4. System wakes from Sx state to S0 state 5. The Host LAN function is transitioned to D0 6. The Host clears the PME_STATUS bit 7. Internal WAKE# signal is deasserted by Host LAN function 5.3.4.1.1 Advanced Power Management Wakeup Advanced Power Management Wakeup, or APM Wakeup, was previously known as Wake on LAN. It is a feature that has existed in the 10/100 Mbps NICs for several generations. The basic premise is to receive a broadcast or unicast packet with an explicit data pattern, and then to assert a signal to wake-up the system. In the earlier generations, this was accomplished by using a special signal that ran across a cable to a defined connector on the motherboard. The NIC would assert the signal for approximately 50ms to signal a wakeup. The LAN Controller uses (if configured to) an in-band PM_PME message for this. On power-up, the LAN Controller will read the APM Enable bits from the NVM PCI Init Control Word into the APM Enable (APME) bits of the Wakeup Control Register (WUC). These bits control enabling of APM Wakeup. When APM Wakeup is enabled, the LAN Controller checks all incoming packets for Magic Packets. Once the LAN Controller receives a matching magic packet, it will: • Set the Magic Packet Received bit in the Wake Up Status Register (WUS). • Set the PME_Status bit in the Power Management Control / Status Register (PMCSR) and assert the internal WAKE# signal. APM Wakeup is supported in all power states and only disabled if a subsequent NVM read results in the APM Wake Up bit being cleared or the software explicitly writes a 0 to the APM Wake Up (APM) bit of the WUC register. 120 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.3.4.1.2 ACPI Power Management Wakeup The LAN Controller supports ACPI Power Management based Wakeups. It can generate system wake-up events from three sources: • Reception of a Magic Packet. • Reception of a Network Wakeup Packet. • Detection of a link change of state. Activating ACPI Power Management Wakeup requires the following steps: • The driver programs the Wake Up Filter Control Register (WUFC) to indicate the packets it wishes to wake up from and supplies the necessary data to the Ipv4 Address Table (IP4AT) and the Flexible Filter Mask Table (FFMT), Flexible Filter Length Table (FFLT), and the Flexible Filter Value Table (FFVT). It can also set the Link Status Change Wake Up Enable (LNKC) bit in the Wake Up Filter Control Register (WUFC) to cause wakeup when the link changes state. • The OS (at configuration time) writes a 1 to the PME_EN bit of the Power Management Control / Status Register (PMCSR.8). Normally, after enabling wakeup, the OS will write 11b to the lower two bits of the PMCSR to put the LAN Controller into low-power mode. Once Wakeup is enabled, the LAN Controller monitors incoming packets, first filtering them according to its standard address filtering method, then filtering them with all of the enabled wakeup filters. If a packet passes both the standard address filtering and at least one of the enabled wakeup filters, the LAN Controller will: • Set the PME_Status bit in the Power Management Control / Status Register (PMCSR) • If the PME_EN bit in the Power Management Control / Status Register (PMCSR) is set, assert the internal WAKE# signal. • Set one or more of the Received bits in the Wake Up Status Register (WUS). (More than one bit will be set if a packet matches more than one filter.) If enabled, a link state change wakeup will cause similar results, setting PME_Status, asserting the internal WAKE# signal and setting the Link Status Changed (LNKC) bit in the Wake Up Status Register (WUS) when the link goes up or down. The internal WAKE# signal will remain asserted until the OS either writes a 1 to the PME_Status bit of the PMCSR register or writes a 0 to the PME_En bit. After receiving a wakeup packet, the LAN Controller will ignore any subsequent wakeup packets until the driver clears all of the Received bits in the Wake Up Status Register (WUS). It will also ignore link change events until the driver clears the Link Status Changed (LNKC) bit in the Wake Up Status Register (WUS). 5.3.5 Configurable LEDs The LAN Controller supports 3 controllable and configurable LEDs that are driven from the LAN Connect Device. Each of the three LED outputs can be individually configured to select the particular event, state, or activity, which will be indicated on that output. In addition, each LED can be individually configured for output polarity as well as for blinking versus non-blinking (steady-state) indication. The configuration for LED outputs is specified via the LEDCTL register. Furthermore, the hardware-default configuration for all the LED outputs, can be specified via NVM fields, thereby supporting LED displays configurable to a particular OEM preference. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 121 Functional Description Each of the 3 LED's may be configured to use one of a variety of sources for output indication. The MODE bits control the LED source: • LINK_100/1000 is asserted when link is established at either 100 or 1000Mbps. • LINK_10/1000 is asserted when link is established at either 10 or 1000Mbps. • LINK_UP is asserted when any speed link is established and maintained. ACTIVITY is asserted when link is established and packets are being transmitted or received. • LINK/ACTIVITY is asserted when link is established AND there is NO transmit or receive activity • LINK_10 is asserted when a 10Mbps link is established and maintained. • LINK_100 is asserted when a 100Mbps link is established and maintained. • LINK_1000 is asserted when a 1000Mbps link is established and maintained. • FULL_DUPLEX is asserted when the link is configured for full duplex operation. • COLLISION is asserted when a collision is observed. • PAUSED is asserted when the device's transmitter is flow controlled. • LED_ON is always asserted; LED_OFF is always de-asserted. The IVRT bits allow the LED source to be inverted before being output or observed by the blink-control logic. LED outputs are assumed to normally be connected to the negative side (cathode) of an external LED. The BLINK bits control whether the LED should be blinked while the LED source is asserted, and the blinking frequency (either 200ms on and 200ms off or 83ms on and 83ms off). The blink control may be especially useful for ensuring that certain events, such as ACTIVITY indication, cause LED transitions, which are sufficiently visible to a human eye. The same blinking rate is shared by all LEDs 5.3.6 Function Level Reset Support (FLR) The Gigabit LAN Controller supports the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel® Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a PCI reset was asserted. 5.3.6.1 FLR Steps 5.3.6.1.1 FLR Initialization 1) A FLR is initiated by software writing a ‘1’ to the Initiate FLR bit. 2) All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.3.6.1.2 FLR Operation Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 122 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.3.6.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: From the time Initiate FLR bit is written to '1' software must wait at least 100ms before accessing the function. 5.4 LPC Bridge (w/ System and Management Functions) (D31:F0) The LPC bridge function of the ICH9 resides in PCI Device 31:Function 0. In addition to the LPC bridge function, D31:F0 contains other functional units including DMA, Interrupt controllers, Timers, Power Management, System Management, GPIO, and RTC. In this chapter, registers and functions associated with other functional units (power management, GPIO, USB, etc.) are described in their respective sections. Note: The LPC bridge cannot be configured as a subtractive decode agent. 5.4.1 LPC Interface The ICH9 implements an LPC interface as described in the Low Pin Count Interface Specification, Revision 1.1. The LPC interface to the ICH9 is shown in Figure 5-2. Note that the ICH9 implements all of the signals that are shown as optional, but peripherals are not required to do so. Figure 5-2. LPC Interface Diagram PCI Bus PCI CLK Intel® ICH9 PCI RST# PCI SERIRQ PCI PME# LAD [3:0] LFRAME# SUS_STAT# GPI Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LDRQ[1:0]# (Optional) LPCPD# (Optional) LPC Device LSMI# (Optional) 123 Functional Description 5.4.1.1 LPC Cycle Types The ICH9 implements all of the cycle types described in the Low Pin Count Interface Specification, Revision 1.0. Table 5-5 shows the cycle types supported by the ICH9. Table 5-5. LPC Cycle Types Supported Cycle Type Comment I/O Read 1 byte only. Intel® ICH9 breaks up 16- and 32-bit processor cycles into multiple 8-bit transfers. I/O Write 1 byte only. ICH9 breaks up 16- and 32-bit processor cycles into multiple 8-bit transfers. DMA Read Can be 1, or 2 bytes DMA Write Can be 1, or 2 bytes Bus Master Read Can be 1, 2, or 4 bytes. (See Note 1 below) Bus Master Write Can be 1, 2, or 4 bytes. (See Note 1 below) NOTES: 1. Bus Master Read or Write cycles must be naturally aligned. For example, a 1-byte transfer can be to any address. However, the 2-byte transfer must be word-aligned (i.e., with an address where A0=0). A dword transfer must be dword-aligned (i.e., with an address where A1 and A0 are both 0). 5.4.1.2 Start Field Definition Table 5-6. Start Field Bit Definitions Bits[3:0] Encoding Definition 0000 Start of cycle for a generic target 0010 Grant for bus master 0 0011 Grant for bus master 1 1111 Stop/Abort: End of a cycle for a target. NOTE: All other encodings are RESERVED. 124 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.4.1.3 Cycle Type / Direction (CYCTYPE + DIR) The ICH9 always drives bit 0 of this field to 0. Peripherals running bus master cycles must also drive bit 0 to 0. Table 5-7 shows the valid bit encodings. Table 5-7. Cycle Type Bit Definitions Bits[3:2] Bit1 00 0 I/O Read 00 1 I/O Write 10 0 DMA Read 10 1 DMA Write x Reserved. If a peripheral performing a bus master cycle generates this value, the Intel® ICH9 aborts the cycle. 11 5.4.1.4 Definition Size Bits[3:2] are reserved. The ICH9 always drives them to 00. Peripherals running bus master cycles are also supposed to drive 00 for bits 3:2; however, the ICH9 ignores those bits. Bits[1:0] are encoded as listed in Table 5-8. Table 5-8. Transfer Size Bit Definition Bits[1:0] Size 00 8-bit transfer (1 byte) 01 16-bit transfer (2 bytes) 10 Reserved. The Intel® ICH9 never drives this combination. If a peripheral running a bus master cycle drives this combination, the ICH9 may abort the transfer. 11 32-bit transfer (4 bytes) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 125 Functional Description 5.4.1.5 SYNC Valid values for the SYNC field are shown in Table 5-9. Table 5-9. SYNC Bit Definition Bits[3:0] Indication 0000 Ready: SYNC achieved with no error. For DMA transfers, this also indicates DMA request deassertion and no more transfers desired for that channel. 0101 Short Wait: Part indicating wait-states. For bus master cycles, the Intel® ICH9 does not use this encoding. Instead, the ICH9 uses the Long Wait encoding (see next encoding below). 0110 Long Wait: Part indicating wait-states, and many wait-states will be added. This encoding driven by the ICH9 for bus master cycles, rather than the Short Wait (0101). 1001 Ready More (Used only by peripheral for DMA cycle): SYNC achieved with no error and more DMA transfers desired to continue after this transfer. This value is valid only on DMA transfers and is not allowed for any other type of cycle. 1010 Error: Sync achieved with error. This is generally used to replace the SERR# or IOCHK# signal on the PCI/ISA bus. It indicates that the data is to be transferred, but there is a serious error in this transfer. For DMA transfers, this not only indicates an error, but also indicates DMA request deassertion and no more transfers desired for that channel. NOTES: 1. All other combinations are RESERVED. 2. If the LPC controller receives any SYNC returned from the device other than short (0101), long wait (0110), or ready (0000) when running a FWH cycle, indeterminate results may occur. A FWH device is not allowed to assert an Error SYNC. 5.4.1.6 SYNC Time-Out There are several error cases that can occur on the LPC interface. The ICH9 responds as defined in section 4.2.1.9 of the Low Pin Count Interface Specification, Revision 1.1 to the stimuli described therein. There may be other peripheral failure conditions; however, these are not handled by the ICH9. 5.4.1.7 SYNC Error Indication The ICH9 responds as defined in section 4.2.1.10 of the Low Pin Count Interface Specification, Revision 1.1. Upon recognizing the SYNC field indicating an error, the ICH9 treats this as an SERR by reporting this into the Device 31 Error Reporting Logic. 126 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.4.1.8 LFRAME# Usage The ICH9 follows the usage of LFRAME# as defined in the Low Pin Count Interface Specification, Revision 1.1. The ICH9 performs an abort for the following cases (possible failure cases): • ICH9 starts a Memory, I/O, or DMA cycle, but no device drives a valid SYNC after four consecutive clocks. • ICH9 starts a Memory, I/O, or DMA cycle, and the peripheral drives an invalid SYNC pattern. • A peripheral drives an invalid address when performing bus master cycles. • A peripheral drives an invalid value. 5.4.1.9 I/O Cycles For I/O cycles targeting registers specified in the ICH9’s decode ranges, the ICH9 performs I/O cycles as defined in the Low Pin Count Interface Specification, Revision 1.1. These are 8-bit transfers. If the processor attempts a 16-bit or 32-bit transfer, the ICH9 breaks the cycle up into multiple 8-bit transfers to consecutive I/O addresses. Note: If the cycle is not claimed by any peripheral (and subsequently aborted), the ICH9 returns a value of all 1s (FFh) to the processor. This is to maintain compatibility with ISA I/O cycles where pull-up resistors would keep the bus high if no device responds. 5.4.1.10 Bus Master Cycles The ICH9 supports Bus Master cycles and requests (using LDRQ#) as defined in the Low Pin Count Interface Specification, Revision 1.1. The ICH9 has two LDRQ# inputs, and thus supports two separate bus master devices. It uses the associated START fields for Bus Master 0 (0010b) or Bus Master 1 (0011b). Note: The ICH9 does not support LPC Bus Masters performing I/O cycles. LPC Bus Masters should only perform memory read or memory write cycles. 5.4.1.11 LPC Power Management CLKRUN# Protocol (Mobile Only) The CLKRUN# protocol is same as the PCI Local Bus Specification. Stopping the PCI clock stops the LPC clock. LPCPD# Protocol Same timings as for SUS_STAT#. Upon driving SUS_STAT# low, LPC peripherals drive LDRQ# low or tri-state it. ICH9 shuts off the LDRQ# input buffers. After driving SUS_STAT# active, the ICH9 drives LFRAME# low, and tri-states (or drive low) LAD[3:0]. Note: The Low Pin Count Interface Specification, Revision 1.1 defines the LPCPD# protocol where there is at least 30 µs from LPCPD# assertion to LRST# assertion. This specification explicitly states that this protocol only applies to entry/exit of low power states which does not include asynchronous reset events. The ICH9 asserts both SUS_STAT# (connects to LPCPD#) and PLTRST# (connects to LRST#) at the same time when the core logic is reset (via CF9h, PWROK, or SYS_RESET#, etc.). This is not inconsistent with the LPC LPCPD# protocol. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 127 Functional Description 5.4.1.12 Configuration and Intel® ICH9 Implications LPC I/F Decoders To allow the I/O cycles and memory mapped cycles to go to the LPC interface, the ICH9 includes several decoders. During configuration, the ICH9 must be programmed with the same decode ranges as the peripheral. The decoders are programmed via the Device 31:Function 0 configuration space. Note: The ICH9 cannot accept PCI write cycles from PCI-to-PCI bridges or devices with similar characteristics (specifically those with a “Retry Read” feature which is enabled) to an LPC device if there is an outstanding LPC read cycle towards the same PCI device or bridge. These cycles are not part of normal system operation, but may be encountered as part of platform validation testing using custom test fixtures. Bus Master Device Mapping and START Fields Bus Masters must have a unique START field. In the case of the ICH9 that supports two LPC bus masters, it drives 0010 for the START field for grants to bus master #0 (requested via LDRQ0#) and 0011 for grants to bus master #1 (requested via LDRQ1#.). Thus, no registers are needed to configure the START fields for a particular bus master. 5.5 DMA Operation (D31:F0) The ICH9 supports LPC DMA using the ICH9’s DMA controller. The DMA controller has registers that are fixed in the lower 64 KB of I/O space. The DMA controller is configured using registers in the PCI configuration space. These registers allow configuration of the channels for use by LPC DMA. The DMA circuitry incorporates the functionality of two 82C37 DMA controllers with seven independently programmable channels (Figure 5-3). DMA controller 1 (DMA-1) corresponds to DMA channels 0–3 and DMA controller 2 (DMA-2) corresponds to channels 5–7. DMA channel 4 is used to cascade the two controllers and defaults to cascade mode in the DMA Channel Mode (DCM) Register. Channel 4 is not available for any other purpose. In addition to accepting requests from DMA slaves, the DMA controller also responds to requests that software initiates. Software may initiate a DMA service request by setting any bit in the DMA Channel Request Register to a 1. Figure 5-3. Intel® ICH9 DMA Controller Channel 4 Channel 0 Channel 1 Channel 5 DMA-1 Channel 2 Channel 6 Channel 3 Channel 7 DMA-2 Each DMA channel is hardwired to the compatible settings for DMA device size: channels [3:0] are hardwired to 8-bit, count-by-bytes transfers, and channels [7:5] are hardwired to 16-bit, count-by-words (address shifted) transfers. ICH9 provides 24-bit addressing in compliance with the ISA-Compatible specification. Each channel includes a 16-bit ISA-Compatible Current Register which holds the 16 least-significant bits of the 24-bit address, an ISA-Compatible Page Register which contains the eight next most significant bits of address. 128 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description The DMA controller also features refresh address generation, and auto-initialization following a DMA termination. 5.5.1 Channel Priority For priority resolution, the DMA consists of two logical channel groups: channels 0–3 and channels 4–7. Each group may be in either fixed or rotate mode, as determined by the DMA Command Register. DMA I/O slaves normally assert their DREQ line to arbitrate for DMA service. However, a software request for DMA service can be presented through each channel's DMA Request Register. A software request is subject to the same prioritization as any hardware request. See the detailed register description for Request Register programming information in Section 13.2. 5.5.1.1 Fixed Priority The initial fixed priority structure is as follows: High priority Low priority 0, 1, 2, 3 5, 6, 7 The fixed priority ordering is 0, 1, 2, 3, 5, 6, and 7. In this scheme, channel 0 has the highest priority, and channel 7 has the lowest priority. Channels [3:0] of DMA-1 assume the priority position of channel 4 in DMA-2, thus taking priority over channels 5, 6, and 7. 5.5.1.2 Rotating Priority Rotation allows for “fairness” in priority resolution. The priority chain rotates so that the last channel serviced is assigned the lowest priority in the channel group (0–3, 5–7). Channels 0–3 rotate as a group of 4. They are always placed between channel 5 and channel 7 in the priority list. Channel 5–7 rotate as part of a group of 4. That is, channels (5–7) form the first three positions in the rotation, while channel group (0–3) comprises the fourth position in the arbitration. 5.5.2 Address Compatibility Mode When the DMA is operating, the addresses do not increment or decrement through the High and Low Page Registers. Therefore, if a 24-bit address is 01FFFFh and increments, the next address is 010000h, not 020000h. Similarly, if a 24-bit address is 020000h and decrements, the next address is 02FFFFh, not 01FFFFh. However, when the DMA is operating in 16-bit mode, the addresses still do not increment or decrement through the High and Low Page Registers but the page boundary is now 128 K. Therefore, if a 24-bit address is 01FFFEh and increments, the next address is 000000h, not 0100000h. Similarly, if a 24-bit address is 020000h and decrements, the next address is 03FFFEh, not 02FFFEh. This is compatible with the 82C37 and Page Register implementation used in the PC-AT. This mode is set after CPURST is valid. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 129 Functional Description 5.5.3 Summary of DMA Transfer Sizes Table 5-10 lists each of the DMA device transfer sizes. The column labeled “Current Byte/Word Count Register” indicates that the register contents represents either the number of bytes to transfer or the number of 16-bit words to transfer. The column labeled “Current Address Increment/Decrement” indicates the number added to or taken from the Current Address register after each DMA transfer cycle. The DMA Channel Mode Register determines if the Current Address Register will be incremented or decremented. 5.5.3.1 Address Shifting When Programmed for 16-Bit I/O Count by Words Table 5-10. DMA Transfer Size Current Byte/Word Count Register Current Address Increment/ Decrement 8-Bit I/O, Count By Bytes Bytes 1 16-Bit I/O, Count By Words (Address Shifted) Words 1 DMA Device Date Size And Word Count The ICH9 maintains compatibility with the implementation of the DMA in the PC AT that used the 82C37. The DMA shifts the addresses for transfers to/from a 16-bit device count-by-words. Note: The least significant bit of the Low Page Register is dropped in 16-bit shifted mode. When programming the Current Address Register (when the DMA channel is in this mode), the Current Address must be programmed to an even address with the address value shifted right by one bit. The address shifting is shown in Table 5-11. Table 5-11. Address Shifting in 16-Bit I/O DMA Transfers Output Address 8-Bit I/O Programmed Address (Ch 0–3) 16-Bit I/O Programmed Address (Ch 5–7) (Shifted) A0 A[16:1] A[23:17] A0 A[16:1] A[23:17] 0 A[15:0] A[23:17] NOTE: The least significant bit of the Page Register is dropped in 16-bit shifted mode. 5.5.4 Autoinitialize By programming a bit in the DMA Channel Mode Register, a channel may be set up as an autoinitialize channel. When a channel undergoes autoinitialization, the original values of the Current Page, Current Address and Current Byte/Word Count Registers are automatically restored from the Base Page, Address, and Byte/Word Count Registers of that channel following TC. The Base Registers are loaded simultaneously with the Current Registers by the microprocessor when the DMA channel is programmed and remain unchanged throughout the DMA service. The mask bit is not set when the channel is in autoinitialize. Following autoinitialize, the channel is ready to perform another DMA service, without processor intervention, as soon as a valid DREQ is detected. 130 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.5.5 Software Commands There are three additional special software commands that the DMA controller can execute. The three software commands are: • Clear Byte Pointer Flip-Flop • Master Clear • Clear Mask Register They do not depend on any specific bit pattern on the data bus. 5.6 LPC DMA DMA on LPC is handled through the use of the LDRQ# lines from peripherals and special encodings on LAD[3:0] from the host. Single, Demand, Verify, and Increment modes are supported on the LPC interface. Channels 0–3 are 8 bit channels. Channels 5–7 are 16-bit channels. Channel 4 is reserved as a generic bus master request. 5.6.1 Asserting DMA Requests Peripherals that need DMA service encode their requested channel number on the LDRQ# signal. To simplify the protocol, each peripheral on the LPC I/F has its own dedicated LDRQ# signal (they may not be shared between two separate peripherals). The ICH9 has two LDRQ# inputs, allowing at least two devices to support DMA or bus mastering. LDRQ# is synchronous with LCLK (PCI clock). As shown in Figure 5-4, the peripheral uses the following serial encoding sequence: • Peripheral starts the sequence by asserting LDRQ# low (start bit). LDRQ# is high during idle conditions. • The next three bits contain the encoded DMA channel number (MSB first). • The next bit (ACT) indicates whether the request for the indicated DMA channel is active or inactive. The ACT bit is 1 (high) to indicate if it is active and 0 (low) if it is inactive. The case where ACT is low is rare, and is only used to indicate that a previous request for that channel is being abandoned. • After the active/inactive indication, the LDRQ# signal must go high for at least 1 clock. After that one clock, LDRQ# signal can be brought low to the next encoding sequence. If another DMA channel also needs to request a transfer, another sequence can be sent on LDRQ#. For example, if an encoded request is sent for channel 2, and then channel 3 needs a transfer before the cycle for channel 2 is run on the interface, the peripheral can send the encoded request for channel 3. This allows multiple DMA agents behind an I/O device to request use of the LPC interface, and the I/O device does not need to selfarbitrate before sending the message. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 131 Functional Description Figure 5-4. DMA Request Assertion through LDRQ# LCLK LDRQ# 5.6.2 Start MSB LSB ACT Start Abandoning DMA Requests DMA Requests can be deasserted in two fashions: on error conditions by sending an LDRQ# message with the ‘ACT’ bit set to 0, or normally through a SYNC field during the DMA transfer. This section describes boundary conditions where the DMA request needs to be removed prior to a data transfer. There may be some special cases where the peripheral desires to abandon a DMA transfer. The most likely case of this occurring is due to a floppy disk controller which has overrun or underrun its FIFO, or software stopping a device prematurely. In these cases, the peripheral wishes to stop further DMA activity. It may do so by sending an LDRQ# message with the ACT bit as 0. However, since the DMA request was seen by the ICH9, there is no assurance that the cycle has not been granted and will shortly run on LPC. Therefore, peripherals must take into account that a DMA cycle may still occur. The peripheral can choose not to respond to this cycle, in which case the host will abort it, or it can choose to complete the cycle normally with any random data. This method of DMA deassertion should be prevented whenever possible, to limit boundary conditions both on the ICH9 and the peripheral. 5.6.3 General Flow of DMA Transfers Arbitration for DMA channels is performed through the 8237 within the host. Once the host has won arbitration on behalf of a DMA channel assigned to LPC, it asserts LFRAME# on the LPC I/F and begins the DMA transfer. The general flow for a basic DMA transfer is as follows: 1. ICH9 starts transfer by asserting 0000b on LAD[3:0] with LFRAME# asserted. 2. ICH9 asserts ‘cycle type’ of DMA, direction based on DMA transfer direction. 3. ICH9 asserts channel number and, if applicable, terminal count. 4. ICH9 indicates the size of the transfer: 8 or 16 bits. 5. If a DMA read… — The ICH9 drives the first 8 bits of data and turns the bus around. — The peripheral acknowledges the data with a valid SYNC. — If a 16-bit transfer, the process is repeated for the next 8 bits. 6. If a DMA write… — The ICH9 turns the bus around and waits for data. — The peripheral indicates data ready through SYNC and transfers the first byte. — If a 16-bit transfer, the peripheral indicates data ready and transfers the next byte. 7. The peripheral turns around the bus. 132 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.6.4 Terminal Count Terminal count is communicated through LAD[3] on the same clock that DMA channel is communicated on LAD[2:0]. This field is the CHANNEL field. Terminal count indicates the last byte of transfer, based upon the size of the transfer. For example, on an 8-bit transfer size (SIZE field is 00b), if the TC bit is set, then this is the last byte. On a 16-bit transfer (SIZE field is 01b), if the TC bit is set, then the second byte is the last byte. The peripheral, therefore, must internalize the TC bit when the CHANNEL field is communicated, and only signal TC when the last byte of that transfer size has been transferred. 5.6.5 Verify Mode Verify mode is supported on the LPC interface. A verify transfer to the peripheral is similar to a DMA write, where the peripheral is transferring data to main memory. The indication from the host is the same as a DMA write, so the peripheral will be driving data onto the LPC interface. However, the host will not transfer this data into main memory. 5.6.6 DMA Request Deassertion An end of transfer is communicated to the ICH9 through a special SYNC field transmitted by the peripheral. An LPC device must not attempt to signal the end of a transfer by deasserting LDREQ#. If a DMA transfer is several bytes (e.g., a transfer from a demand mode device) the ICH9 needs to know when to deassert the DMA request based on the data currently being transferred. The DMA agent uses a SYNC encoding on each byte of data being transferred, which indicates to the ICH9 whether this is the last byte of transfer or if more bytes are requested. To indicate the last byte of transfer, the peripheral uses a SYNC value of 0000b (ready with no error), or 1010b (ready with error). These encodings tell the ICH9 that this is the last piece of data transferred on a DMA read (ICH9 to peripheral), or the byte that follows is the last piece of data transferred on a DMA write (peripheral to ICH9). When the ICH9 sees one of these two encodings, it ends the DMA transfer after this byte and deasserts the DMA request to the 8237. Therefore, if the ICH9 indicated a 16bit transfer, the peripheral can end the transfer after one byte by indicating a SYNC value of 0000b or 1010b. The ICH9 does not attempt to transfer the second byte, and deasserts the DMA request internally. If the peripheral indicates a 0000b or 1010b SYNC pattern on the last byte of the indicated size, then the ICH9 only deasserts the DMA request to the 8237 since it does not need to end the transfer. If the peripheral wishes to keep the DMA request active, then it uses a SYNC value of 1001b (ready plus more data). This tells the 8237 that more data bytes are requested after the current byte has been transferred, so the ICH9 keeps the DMA request active to the 8237. Therefore, on an 8-bit transfer size, if the peripheral indicates a SYNC value of 1001b to the ICH9, the data will be transferred and the DMA request will remain active to the 8237. At a later time, the ICH9 will then come back with another START–CYCTYPE–CHANNEL–SIZE etc. combination to initiate another transfer to the peripheral. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 133 Functional Description The peripheral must not assume that the next START indication from the ICH9 is another grant to the peripheral if it had indicated a SYNC value of 1001b. On a single mode DMA device, the 8237 will re-arbitrate after every transfer. Only demand mode DMA devices can be assured that they will receive the next START indication from the ICH9. Note: Indicating a 0000b or 1010b encoding on the SYNC field of an odd byte of a 16-bit channel (first byte of a 16-bit transfer) is an error condition. Note: The host stops the transfer on the LPC bus as indicated, fills the upper byte with random data on DMA writes (peripheral to memory), and indicates to the 8237 that the DMA transfer occurred, incrementing the 8237’s address and decrementing its byte count. 5.6.7 SYNC Field / LDRQ# Rules Since DMA transfers on LPC are requested through an LDRQ# assertion message, and are ended through a SYNC field during the DMA transfer, the peripheral must obey the following rule when initiating back-to-back transfers from a DMA channel. The peripheral must not assert another message for eight LCLKs after a deassertion is indicated through the SYNC field. This is needed to allow the 8237, that typically runs off a much slower internal clock, to see a message deasserted before it is re-asserted so that it can arbitrate to the next agent. Under default operation, the host only performs 8-bit transfers on 8-bit channels and 16-bit transfers on 16-bit channels. The method by which this communication between host and peripheral through system BIOS is performed is beyond the scope of this specification. Since the LPC host and LPC peripheral are motherboard devices, no “plug-n-play” registry is required. The peripheral must not assume that the host is able to perform transfer sizes that are larger than the size allowed for the DMA channel, and be willing to accept a SIZE field that is smaller than what it may currently have buffered. To that end, it is recommended that future devices that may appear on the LPC bus, that require higher bandwidth than 8-bit or 16-bit DMA allow, do so with a bus mastering interface and not rely on the 8237. 134 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.7 8254 Timers (D31:F0) The ICH9 contains three counters that have fixed uses. All registers and functions associated with the 8254 timers are in the core well. The 8254 unit is clocked by a 14.31818 MHz clock. Counter 0, System Timer This counter functions as the system timer by controlling the state of IRQ0 and is typically programmed for Mode 3 operation. The counter produces a square wave with a period equal to the product of the counter period (838 ns) and the initial count value. The counter loads the initial count value 1 counter period after software writes the count value to the counter I/O address. The counter initially asserts IRQ0 and decrements the count value by two each counter period. The counter negates IRQ0 when the count value reaches 0. It then reloads the initial count value and again decrements the initial count value by two each counter period. The counter then asserts IRQ0 when the count value reaches 0, reloads the initial count value, and repeats the cycle, alternately asserting and negating IRQ0. Counter 1, Refresh Request Signal This counter provides the refresh request signal and is typically programmed for Mode 2 operation and only impacts the period of the REF_TOGGLE bit in Port 61. The initial count value is loaded one counter period after being written to the counter I/O address. The REF_TOGGLE bit will have a square wave behavior (alternate between 0 and 1) and will toggle at a rate based on the value in the counter. Programming the counter to anything other than Mode 2 will result in undefined behavior for the REF_TOGGLE bit. Counter 2, Speaker Tone This counter provides the speaker tone and is typically programmed for Mode 3 operation. The counter provides a speaker frequency equal to the counter clock frequency (1.193 MHz) divided by the initial count value. The speaker must be enabled by a write to port 061h (see NMI Status and Control ports). 5.7.1 Timer Programming The counter/timers are programmed in the following fashion: 1. Write a control word to select a counter. 2. Write an initial count for that counter. 3. Load the least and/or most significant bytes (as required by Control Word bits 5, 4) of the 16-bit counter. 4. Repeat with other counters. Only two conventions need to be observed when programming the counters. First, for each counter, the control word must be written before the initial count is written. Second, the initial count must follow the count format specified in the control word (least significant byte only, most significant byte only, or least significant byte and then most significant byte). A new initial count may be written to a counter at any time without affecting the counter's programmed mode. Counting is affected as described in the mode definitions. The new count must follow the programmed count format. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 135 Functional Description If a counter is programmed to read/write two-byte counts, the following precaution applies: A program must not transfer control between writing the first and second byte to another routine which also writes into that same counter. Otherwise, the counter will be loaded with an incorrect count. The Control Word Register at port 43h controls the operation of all three counters. Several commands are available: • Control Word Command. Specifies which counter to read or write, the operating mode, and the count format (binary or BCD). • Counter Latch Command. Latches the current count so that it can be read by the system. The countdown process continues. • Read Back Command. Reads the count value, programmed mode, the current state of the OUT pins, and the state of the Null Count Flag of the selected counter. Table 5-12 lists the six operating modes for the interval counters. Table 5-12. Counter Operating Modes Mode 5.7.2 Function Description 0 Out signal on end of count (=0) Output is 0. When count goes to 0, output goes to 1 and stays at 1 until counter is reprogrammed. 1 Hardware retriggerable one-shot Output is 0. When count goes to 0, output goes to 1 for one clock time. 2 Rate generator (divide by n counter) Output is 1. Output goes to 0 for one clock time, then back to 1 and counter is reloaded. 3 Square wave output Output is 1. Output goes to 0 when counter rolls over, and counter is reloaded. Output goes to 1 when counter rolls over, and counter is reloaded, etc. 4 Software triggered strobe Output is 1. Output goes to 0 when count expires for one clock time. 5 Hardware triggered strobe Output is 1. Output goes to 0 when count expires for one clock time. Reading from the Interval Timer It is often desirable to read the value of a counter without disturbing the count in progress. There are three methods for reading the counters: a simple read operation, counter Latch command, and the Read-Back command. Each is explained below. With the simple read and counter latch command methods, the count must be read according to the programmed format; specifically, if the counter is programmed for two byte counts, two bytes must be read. The two bytes do not have to be read one right after the other. Read, write, or programming operations for other counters may be inserted between them. 5.7.2.1 Simple Read The first method is to perform a simple read operation. The counter is selected through port 40h (counter 0), 41h (counter 1), or 42h (counter 2). Note: 136 Performing a direct read from the counter does not return a determinate value, because the counting process is asynchronous to read operations. However, in the case of counter 2, the count can be stopped by writing to the GATE bit in port 61h. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.7.2.2 Counter Latch Command The Counter Latch command, written to port 43h, latches the count of a specific counter at the time the command is received. This command is used to ensure that the count read from the counter is accurate, particularly when reading a two-byte count. The count value is then read from each counter’s Count register as was programmed by the Control register. The count is held in the latch until it is read or the counter is reprogrammed. The count is then unlatched. This allows reading the contents of the counters on the fly without affecting counting in progress. Multiple Counter Latch Commands may be used to latch more than one counter. Counter Latch commands do not affect the programmed mode of the counter in any way. If a Counter is latched and then, some time later, latched again before the count is read, the second Counter Latch command is ignored. The count read is the count at the time the first Counter Latch command was issued. 5.7.2.3 Read Back Command The Read Back command, written to port 43h, latches the count value, programmed mode, and current states of the OUT pin and Null Count flag of the selected counter or counters. The value of the counter and its status may then be read by I/O access to the counter address. The Read Back command may be used to latch multiple counter outputs at one time. This single command is functionally equivalent to several counter latch commands, one for each counter latched. Each counter's latched count is held until it is read or reprogrammed. Once read, a counter is unlatched. The other counters remain latched until they are read. If multiple count Read Back commands are issued to the same counter without reading the count, all but the first are ignored. The Read Back command may additionally be used to latch status information of selected counters. The status of a counter is accessed by a read from that counter's I/ O port address. If multiple counter status latch operations are performed without reading the status, all but the first are ignored. Both count and status of the selected counters may be latched simultaneously. This is functionally the same as issuing two consecutive, separate Read Back commands. If multiple count and/or status Read Back commands are issued to the same counters without any intervening reads, all but the first are ignored. If both count and status of a counter are latched, the first read operation from that counter returns the latched status, regardless of which was latched first. The next one or two reads, depending on whether the counter is programmed for one or two type counts, returns the latched count. Subsequent reads return unlatched count. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 137 Functional Description 5.8 8259 Interrupt Controllers (PIC) (D31:F0) The ICH9 incorporates the functionality of two 8259 interrupt controllers that provide system interrupts for the ISA compatible interrupts. These interrupts are: system timer, keyboard controller, serial ports, parallel ports, floppy disk, mouse, and DMA channels. In addition, this interrupt controller can support the PCI based interrupts, by mapping the PCI interrupt onto the compatible ISA interrupt line. Each 8259 core supports eight interrupts, numbered 0–7. Table 5-13 shows how the cores are connected. . Table 5-13. Interrupt Controller Core Connections 8259 Master Slave 8259 Input Typical Interrupt Source Connected Pin / Function 0 Internal Internal Timer / Counter 0 output / HPET #0 1 Keyboard IRQ1 via SERIRQ 2 Internal Slave controller INTR output 3 Serial Port A IRQ3 via SERIRQ, PIRQ# 4 Serial Port B IRQ4 via SERIRQ, PIRQ# 5 Parallel Port / Generic IRQ5 via SERIRQ, PIRQ# 6 Floppy Disk IRQ6 via SERIRQ, PIRQ# 7 Parallel Port / Generic IRQ7 via SERIRQ, PIRQ# 0 Internal Real Time Clock Internal RTC / HPET #1 1 Generic IRQ9 via SERIRQ, SCI, TCO, or PIRQ# 2 Generic IRQ10 via SERIRQ, SCI, TCO, or PIRQ# 3 Generic IRQ11 via SERIRQ, SCI, TCO, or PIRQ#, or HPET #2 4 PS/2 Mouse IRQ12 via SERIRQ, SCI, TCO, or PIRQ#, or HPET #3 5 Internal State Machine output based on processor FERR# assertion. May optionally be used for SCI or TCO interrupt if FERR# not needed. 6 SATA SATA Primary (legacy mode), or via SERIRQ or PIRQ# 7 SATA SATA Secondary (legacy mode) or via SERIRQ or PIRQ# The ICH9 cascades the slave controller onto the master controller through master controller interrupt input 2. This means there are only 15 possible interrupts for the ICH9 PIC. Interrupts can individually be programmed to be edge or level, except for IRQ0, IRQ2, IRQ8#, and IRQ13. Note: 138 Active-low interrupt sources (e.g., the PIRQ#s) are inverted inside the ICH9. In the following descriptions of the 8259s, the interrupt levels are in reference to the signals at the internal interface of the 8259s, after the required inversions have occurred. Therefore, the term “high” indicates “active,” which means “low” on an originating PIRQ#. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.8.1 Interrupt Handling 5.8.1.1 Generating Interrupts The PIC interrupt sequence involves three bits, from the IRR, ISR, and IMR, for each interrupt level. These bits are used to determine the interrupt vector returned, and status of any other pending interrupts. Table 5-14 defines the IRR, ISR, and IMR. Table 5-14. Interrupt Status Registers 5.8.1.2 Bit Description IRR Interrupt Request Register. This bit is set on a low to high transition of the interrupt line in edge mode, and by an active high level in level mode. This bit is set whether or not the interrupt is masked. However, a masked interrupt will not generate INTR. ISR Interrupt Service Register. This bit is set, and the corresponding IRR bit cleared, when an interrupt acknowledge cycle is seen, and the vector returned is for that interrupt. IMR Interrupt Mask Register. This bit determines whether an interrupt is masked. Masked interrupts will not generate INTR. Acknowledging Interrupts The processor generates an interrupt acknowledge cycle that is translated by the host bridge into a PCI Interrupt Acknowledge Cycle to the ICH9. The PIC translates this command into two internal INTA# pulses expected by the 8259 cores. The PIC uses the first internal INTA# pulse to freeze the state of the interrupts for priority resolution. On the second INTA# pulse, the master or slave sends the interrupt vector to the processor with the acknowledged interrupt code. This code is based upon bits [7:3] of the corresponding ICW2 register, combined with three bits representing the interrupt within that controller. Table 5-15. Content of Interrupt Vector Byte Master, Slave Interrup t Bits [7:3] Bits [2:0] IRQ7,15 111 IRQ6,14 110 IRQ5,13 101 IRQ4,12 IRQ3,11 ICW2[7:3] 100 011 IRQ2,10 010 IRQ1,9 001 IRQ0,8 000 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 139 Functional Description 5.8.1.3 Hardware/Software Interrupt Sequence 1. One or more of the Interrupt Request lines (IRQ) are raised high in edge mode, or seen high in level mode, setting the corresponding IRR bit. 2. The PIC sends INTR active to the processor if an asserted interrupt is not masked. 3. The processor acknowledges the INTR and responds with an interrupt acknowledge cycle. The cycle is translated into a PCI interrupt acknowledge cycle by the host bridge. This command is broadcast over PCI by the ICH9. 4. Upon observing its own interrupt acknowledge cycle on PCI, the ICH9 converts it into the two cycles that the internal 8259 pair can respond to. Each cycle appears as an interrupt acknowledge pulse on the internal INTA# pin of the cascaded interrupt controllers. 5. Upon receiving the first internally generated INTA# pulse, the highest priority ISR bit is set and the corresponding IRR bit is reset. On the trailing edge of the first pulse, a slave identification code is broadcast by the master to the slave on a private, internal three bit wide bus. The slave controller uses these bits to determine if it must respond with an interrupt vector during the second INTA# pulse. 6. Upon receiving the second internally generated INTA# pulse, the PIC returns the interrupt vector. If no interrupt request is present because the request was too short in duration, the PIC returns vector 7 from the master controller. 7. This completes the interrupt cycle. In AEOI mode the ISR bit is reset at the end of the second INTA# pulse. Otherwise, the ISR bit remains set until an appropriate EOI command is issued at the end of the interrupt subroutine. 5.8.2 Initialization Command Words (ICWx) Before operation can begin, each 8259 must be initialized. In the ICH9, this is a four byte sequence. The four initialization command words are referred to by their acronyms: ICW1, ICW2, ICW3, and ICW4. The base address for each 8259 initialization command word is a fixed location in the I/O memory space: 20h for the master controller, and A0h for the slave controller. 5.8.2.1 ICW1 An I/O write to the master or slave controller base address with data bit 4 equal to 1 is interpreted as a write to ICW1. Upon sensing this write, the ICH9 PIC expects three more byte writes to 21h for the master controller, or A1h for the slave controller, to complete the ICW sequence. A write to ICW1 starts the initialization sequence during which the following automatically occur: 1. Following initialization, an interrupt request (IRQ) input must make a low-to-high transition to generate an interrupt. 2. The Interrupt Mask Register is cleared. 3. IRQ7 input is assigned priority 7. 4. The slave mode address is set to 7. 5. Special mask mode is cleared and Status Read is set to IRR. 140 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.8.2.2 ICW2 The second write in the sequence (ICW2) is programmed to provide bits [7:3] of the interrupt vector that will be released during an interrupt acknowledge. A different base is selected for each interrupt controller. 5.8.2.3 ICW3 The third write in the sequence (ICW3) has a different meaning for each controller. • For the master controller, ICW3 is used to indicate which IRQ input line is used to cascade the slave controller. Within the ICH9, IRQ2 is used. Therefore, bit 2 of ICW3 on the master controller is set to a 1, and the other bits are set to 0s. • For the slave controller, ICW3 is the slave identification code used during an interrupt acknowledge cycle. On interrupt acknowledge cycles, the master controller broadcasts a code to the slave controller if the cascaded interrupt won arbitration on the master controller. The slave controller compares this identification code to the value stored in its ICW3, and if it matches, the slave controller assumes responsibility for broadcasting the interrupt vector. 5.8.2.4 ICW4 The final write in the sequence (ICW4) must be programmed for both controllers. At the very least, bit 0 must be set to a 1 to indicate that the controllers are operating in an Intel Architecture-based system. 5.8.3 Operation Command Words (OCW) These command words reprogram the Interrupt controller to operate in various interrupt modes. • OCW1 masks and unmasks interrupt lines. • OCW2 controls the rotation of interrupt priorities when in rotating priority mode, and controls the EOI function. • OCW3 sets up ISR/IRR reads, enables/disables the special mask mode (SMM), and enables/disables polled interrupt mode. 5.8.4 Modes of Operation 5.8.4.1 Fully Nested Mode In this mode, interrupt requests are ordered in priority from 0 through 7, with 0 being the highest. When an interrupt is acknowledged, the highest priority request is determined and its vector placed on the bus. Additionally, the ISR for the interrupt is set. This ISR bit remains set until: the processor issues an EOI command immediately before returning from the service routine; or if in AEOI mode, on the trailing edge of the second INTA#. While the ISR bit is set, all further interrupts of the same or lower priority are inhibited, while higher levels generate another interrupt. Interrupt priorities can be changed in the rotating priority mode. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 141 Functional Description 5.8.4.2 Special Fully-Nested Mode This mode is used in the case of a system where cascading is used, and the priority has to be conserved within each slave. In this case, the special fully-nested mode is programmed to the master controller. This mode is similar to the fully-nested mode with the following exceptions: • When an interrupt request from a certain slave is in service, this slave is not locked out from the master's priority logic and further interrupt requests from higher priority interrupts within the slave are recognized by the master and initiate interrupts to the processor. In the normal-nested mode, a slave is masked out when its request is in service. • When exiting the Interrupt Service routine, software has to check whether the interrupt serviced was the only one from that slave. This is done by sending a NonSpecific EOI command to the slave and then reading its ISR. If it is 0, a nonspecific EOI can also be sent to the master. 5.8.4.3 Automatic Rotation Mode (Equal Priority Devices) In some applications, there are a number of interrupting devices of equal priority. Automatic rotation mode provides for a sequential 8-way rotation. In this mode, a device receives the lowest priority after being serviced. In the worst case, a device requesting an interrupt has to wait until each of seven other devices are serviced at most once. There are two ways to accomplish automatic rotation using OCW2; the Rotation on Non-Specific EOI Command (R=1, SL=0, EOI=1) and the rotate in automatic EOI mode which is set by (R=1, SL=0, EOI=0). 5.8.4.4 Specific Rotation Mode (Specific Priority) Software can change interrupt priorities by programming the bottom priority. For example, if IRQ5 is programmed as the bottom priority device, then IRQ6 is the highest priority device. The Set Priority Command is issued in OCW2 to accomplish this, where: R=1, SL=1, and LO–L2 is the binary priority level code of the bottom priority device. In this mode, internal status is updated by software control during OCW2. However, it is independent of the EOI command. Priority changes can be executed during an EOI command by using the Rotate on Specific EOI Command in OCW2 (R=1, SL=1, EOI=1 and LO–L2=IRQ level to receive bottom priority. 5.8.4.5 Poll Mode Poll mode can be used to conserve space in the interrupt vector table. Multiple interrupts that can be serviced by one interrupt service routine do not need separate vectors if the service routine uses the poll command. Poll mode can also be used to expand the number of interrupts. The polling interrupt service routine can call the appropriate service routine, instead of providing the interrupt vectors in the vector table. In this mode, the INTR output is not used and the microprocessor internal Interrupt Enable flip-flop is reset, disabling its interrupt input. Service to devices is achieved by software using a Poll command. The Poll command is issued by setting P=1 in OCW3. The PIC treats its next I/O read as an interrupt acknowledge, sets the appropriate ISR bit if there is a request, and reads the priority level. Interrupts are frozen from the OCW3 write to the I/O read. The byte returned during the I/O read contains a 1 in bit 7 if there is an interrupt, and the binary code of the highest priority level in bits 2:0. 142 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.8.4.6 Cascade Mode The PIC in the ICH9 has one master 8259 and one slave 8259 cascaded onto the master through IRQ2. This configuration can handle up to 15 separate priority levels. The master controls the slaves through a three bit internal bus. In the ICH9, when the master drives 010b on this bus, the slave controller takes responsibility for returning the interrupt vector. An EOI command must be issued twice: once for the master and once for the slave. 5.8.4.7 Edge and Level Triggered Mode In ISA systems this mode is programmed using bit 3 in ICW1, which sets level or edge for the entire controller. In the ICH9, this bit is disabled and a new register for edge and level triggered mode selection, per interrupt input, is included. This is the Edge/Level control Registers ELCR1 and ELCR2. If an ELCR bit is 0, an interrupt request will be recognized by a low-to-high transition on the corresponding IRQ input. The IRQ input can remain high without generating another interrupt. If an ELCR bit is 1, an interrupt request will be recognized by a high level on the corresponding IRQ input and there is no need for an edge detection. The interrupt request must be removed before the EOI command is issued to prevent a second interrupt from occurring. In both the edge and level triggered modes, the IRQ inputs must remain active until after the falling edge of the first internal INTA#. If the IRQ input goes inactive before this time, a default IRQ7 vector is returned. 5.8.4.8 End of Interrupt (EOI) Operations An EOI can occur in one of two fashions: by a command word write issued to the PIC before returning from a service routine, the EOI command; or automatically when AEOI bit in ICW4 is set to 1. 5.8.4.9 Normal End of Interrupt In normal EOI, software writes an EOI command before leaving the interrupt service routine to mark the interrupt as completed. There are two forms of EOI commands: Specific and Non-Specific. When a Non-Specific EOI command is issued, the PIC clears the highest ISR bit of those that are set to 1. Non-Specific EOI is the normal mode of operation of the PIC within the ICH9, as the interrupt being serviced currently is the interrupt entered with the interrupt acknowledge. When the PIC is operated in modes that preserve the fully nested structure, software can determine which ISR bit to clear by issuing a Specific EOI. An ISR bit that is masked is not cleared by a Non-Specific EOI if the PIC is in the special mask mode. An EOI command must be issued for both the master and slave controller. 5.8.4.10 Automatic End of Interrupt Mode In this mode, the PIC automatically performs a Non-Specific EOI operation at the trailing edge of the last interrupt acknowledge pulse. From a system standpoint, this mode should be used only when a nested multi-level interrupt structure is not required within a single PIC. The AEOI mode can only be used in the master controller and not the slave controller. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 143 Functional Description 5.8.5 Masking Interrupts 5.8.5.1 Masking on an Individual Interrupt Request Each interrupt request can be masked individually by the Interrupt Mask Register (IMR). This register is programmed through OCW1. Each bit in the IMR masks one interrupt channel. Masking IRQ2 on the master controller masks all requests for service from the slave controller. 5.8.5.2 Special Mask Mode Some applications may require an interrupt service routine to dynamically alter the system priority structure during its execution under software control. For example, the routine may wish to inhibit lower priority requests for a portion of its execution but enable some of them for another portion. The special mask mode enables all interrupts not masked by a bit set in the Mask register. Normally, when an interrupt service routine acknowledges an interrupt without issuing an EOI to clear the ISR bit, the interrupt controller inhibits all lower priority requests. In the special mask mode, any interrupts may be selectively enabled by loading the Mask Register with the appropriate pattern. The special mask mode is set by OCW3 where: SSMM=1, SMM=1, and cleared where SSMM=1, SMM=0. 5.8.6 Steering PCI Interrupts The ICH9 can be programmed to allow PIRQA#-PIRQH# to be routed internally to interrupts 3–7, 9–12, 14 or 15. The assignment is programmable through the PIRQx Route Control registers, located at 60–63h and 68–6Bh in Device 31:Function 0. One or more PIRQx# lines can be routed to the same IRQx input. If interrupt steering is not required, the Route registers can be programmed to disable steering. The PIRQx# lines are defined as active low, level sensitive to allow multiple interrupts on a PCI board to share a single line across the connector. When a PIRQx# is routed to specified IRQ line, software must change the IRQ's corresponding ELCR bit to level sensitive mode. The ICH9 internally inverts the PIRQx# line to send an active high level to the PIC. When a PCI interrupt is routed onto the PIC, the selected IRQ can no longer be used by an active high device (through SERIRQ). However, active low interrupts can share their interrupt with PCI interrupts. Internal sources of the PIRQs, including SCI and TCO interrupts, cause the external PIRQ to be asserted. The ICH9 receives the PIRQ input, like all of the other external sources, and routes it accordingly. 144 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.9 Advanced Programmable Interrupt Controller (APIC) (D31:F0) In addition to the standard ISA-compatible PIC described in the previous chapter, the ICH9 incorporates the APIC. While the standard interrupt controller is intended for use in a uni-processor system, APIC can be used in either a uni-processor or multiprocessor system. 5.9.1 Interrupt Handling The I/O APIC handles interrupts very differently than the 8259. Briefly, these differences are: • Method of Interrupt Transmission. The I/O APIC transmits interrupts through memory writes on the normal datapath to the processor, and interrupts are handled without the need for the processor to run an interrupt acknowledge cycle. • Interrupt Priority. The priority of interrupts in the I/O APIC is independent of the interrupt number. For example, interrupt 10 can be given a higher priority than interrupt 3. • More Interrupts. The I/O APIC in the ICH9 supports a total of 24 interrupts. • Multiple Interrupt Controllers. The I/O APIC architecture allows for multiple I/O APIC devices in the system with their own interrupt vectors. 5.9.2 Interrupt Mapping The I/O APIC within the ICH9 supports 24 APIC interrupts. Each interrupt has its own unique vector assigned by software. The interrupt vectors are mapped as follows, and match “Config 6” of the Multi-Processor Specification. Table 5-16. APIC Interrupt Mapping1 (Sheet 1 of 2) IRQ # Via SERIRQ Direct from Pin Via PCI Message 0 No No No 1 Yes No Yes 2 No No No 3 Yes No Yes 4 Yes No Yes 5 Yes No Yes 6 Yes No Yes 7 Yes No Yes 8 No No No RTC, HPET #1 (legacy mode) Internal Modules Cascade from 8259 #1 8254 Counter 0, HPET #0 (legacy mode) 9 Yes No Yes Option for SCI, TCO 10 Yes No Yes Option for SCI, TCO 11 Yes No Yes HPET #2, Option for SCI, TCO (Note2) 12 Yes No Yes HPET #3 (Note 3) 13 No No No FERR# logic 14 Yes No Yes SATA Primary (legacy mode) 15 Yes No Yes SATA Secondary (legacy mode) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 145 Functional Description Table 5-16. APIC Interrupt Mapping1 (Sheet 2 of 2) IRQ # Via SERIRQ Direct from Pin 16 PIRQA# PIRQA# 17 PIRQB# PIRQB# 18 PIRQC# PIRQC# 19 PIRQD# PIRQD# 20 N/A PIRQE#4 21 N/A PIRQF#4 22 N/A PIRQG#4 23 N/A PIRQH#4 Via PCI Message Internal Modules Yes Internal devices are routable; see Section 10.1.56 though Section 10.1.62. Yes Option for SCI, TCO, HPET #0,1,2, 3. Other internal devices are routable; see Section 10.1.56 through Section 10.1.62. NOTES: 1. When programming the polarity of internal interrupt sources on the APIC, interrupts 0 through 15 receive active-high internal interrupt sources, while interrupts 16 through 23 receive active-low internal interrupt sources. 2. If IRQ 11 is used for HPET #2, software should ensure IRQ 11 is not shared with any other devices to ensure the proper operation of HPET #2. ICH9 hardware does not prevent sharing of IRQ 11. 3. If IRQ 12 is used for HPET #3, software should ensure IRQ 12 is not shared with any other devices to ensure the proper operation of HPET #3. ICH9 hardware does not prevent sharing of IRQ 12. 4. PIRQ[E:H] are Multiplexed with GPIO pins. Interrupts PIRQ[E:H] will not be exposed if they are configured as GPIOs. 5.9.3 PCI / PCI Express* Message-Based Interrupts When external devices through PCI / PCI Express wish to generate an interrupt, they will send the message defined in the PCI Express* Base Specification, Revision 1.0a for generating INTA# - INTD#. These will be translated internal assertions/de-assertions of INTA# - INTD#. 5.9.4 Front Side Bus Interrupt Delivery For processors that support Front Side Bus (FSB) interrupt delivery, the ICH9 requires that the I/O APIC deliver interrupt messages to the processor in a parallel manner, rather than using the I/O APIC serial scheme. This is done by the ICH9 writing (via DMI) to a memory location that is snooped by the processor(s). The processor(s) snoop the cycle to know which interrupt goes active. The following sequence is used: 1. When the ICH9 detects an interrupt event (active edge for edge-triggered mode or a change for level-triggered mode), it sets or resets the internal IRR bit associated with that interrupt. 2. Internally, the ICH9 requests to use the bus in a way that automatically flushes upstream buffers. This can be internally implemented similar to a DMA device request. 3. The ICH9 then delivers the message by performing a write cycle to the appropriate address with the appropriate data. The address and data formats are described below in Section 5.9.4.4. Note: 146 FSB Interrupt Delivery compatibility with processor clock control depends on the processor, not the ICH9. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.9.4.1 Edge-Triggered Operation In this case, the “Assert Message” is sent when there is an inactive-to-active edge on the interrupt. 5.9.4.2 Level-Triggered Operation In this case, the “Assert Message” is sent when there is an inactive-to-active edge on the interrupt. If after the EOI the interrupt is still active, then another “Assert Message” is sent to indicate that the interrupt is still active. 5.9.4.3 Registers Associated with Front Side Bus Interrupt Delivery Capabilities Indication: The capability to support Front Side Bus interrupt delivery is indicated via ACPI configuration techniques. This involves the BIOS creating a data structure that gets reported to the ACPI configuration software. 5.9.4.4 Interrupt Message Format The ICH9 writes the message to PCI (and to the Host controller) as a 32-bit memory write cycle. It uses the formats shown in Table 5-17 and Table 5-18 for the address and data. The local APIC (in the processor) has a delivery mode option to interpret Front Side Bus messages as a SMI in which case the processor treats the incoming interrupt as a SMI instead of as an interrupt. This does not mean that the ICH9 has any way to have a SMI source from ICH9 power management logic cause the I/O APIC to send an SMI message (there is no way to do this). The ICH9’s I/O APIC can only send interrupts due to interrupts which do not include SMI, NMI or INIT. This means that in IA-32/Intel® 64 based platforms, Front Side Bus interrupt message format delivery modes 010 (SMI/ PMI), 100 (NMI), and 101 (INIT) as indicated in this section, must not be used and is not supported. Only the hardware pin connection is supported by ICH9. : Table 5-17. Interrupt Message Address Format Bit Description 31:20 Will always be FEEh 19:12 Destination ID: This is the same as bits 63:56 of the I/O Redirection Table entry for the interrupt associated with this message. 11:4 Extended Destination ID: This is the same as bits 55:48 of the I/O Redirection Table entry for the interrupt associated with this message. Redirection Hint: This bit is used by the processor host bridge to allow the interrupt message to be redirected. 0 = The message will be delivered to the agent (processor) listed in bits 19:12. 3 1 = The message will be delivered to an agent with a lower interrupt priority This can be derived from bits 10:8 in the Data Field (see below). The Redirection Hint bit will be a 1 if bits 10:8 in the delivery mode field associated with corresponding interrupt are encoded as 001 (Lowest Priority). Otherwise, the Redirection Hint bit will be 0 2 1:0 Destination Mode: This bit is used only the Redirection Hint bit is set to 1. If the Redirection Hint bit and the Destination Mode bit are both set to 1, then the logical destination mode is used, and the redirection is limited only to those processors that are part of the logical group as based on the logical ID. Will always be 00. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 147 Functional Description Table 5-18. Interrupt Message Data Format Bit 31:16 Description Will always be 0000h. 15 Trigger Mode: 1 = Level, 0 = Edge. Same as the corresponding bit in the I/O Redirection Table for that interrupt. 14 Delivery Status: 1 = Assert, 0 = Deassert. Only Assert messages are sent. This bit is always 1. 13:12 11 Will always be 00 Destination Mode: 1 = Logical. 0 = Physical. Same as the corresponding bit in the I/O Redirection Table for that interrupt. Delivery Mode: This is the same as the corresponding bits in the I/O Redirection Table for that interrupt. 10:8 000 = Fixed 100 = NMI 001 = Lowest Priority 101 = INIT 010 = SMI/PMI 110 = Reserved 011 = Reserved 111 = ExtINT 7:0 5.9.5 Vector: This is the same as the corresponding bits in the I/O Redirection Table for that interrupt. IOxAPIC Address Remapping In order to support Intel® Virtualization Technology, interrupt messages are required to go through similar address remapping as any other memory request. Address remapping allows for domain isolation for interrupts, so a device assigned in one domain is not allowed to generate an interrupt to another domain. The address remapping is based on the Bus: Device: Function field associated with the requests. The internal APIC is required to initiate the interrupt message using a unique Bus: Device: function. ICH9 allows BIOS to program the unique Bus: Device: Function address for the internal APIC. This address field does not change the APIC functionality and the APIC is not promoted as a stand-alone PCI device. See Device 31: Function 0 Offset 6Ch for additional information. 5.9.6 External Interrupt Controller Support The ICH9 supports external APICs off of PCI Express ports, and does not support APICs on the PCI bus. The EOI special cycle is only forwarded to PCI Express ports. 148 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.10 Serial Interrupt (D31:F0) The ICH9 supports a serial IRQ scheme. This allows a single signal to be used to report interrupt requests. The signal used to transmit this information is shared between the host, the ICH9, and all peripherals that support serial interrupts. The signal line, SERIRQ, is synchronous to PCI clock, and follows the sustained tri-state protocol that is used by all PCI signals. This means that if a device has driven SERIRQ low, it will first drive it high synchronous to PCI clock and release it the following PCI clock. The serial IRQ protocol defines this sustained tri-state signaling in the following fashion: • S – Sample Phase. Signal driven low • R – Recovery Phase. Signal driven high • T – Turn-around Phase. Signal released The ICH9 supports a message for 21 serial interrupts. These represent the 15 ISA interrupts (IRQ0–1, 2–15), the four PCI interrupts, and the control signals SMI# and IOCHK#. The serial IRQ protocol does not support the additional APIC interrupts (20– 23). Note: When the SATA controller is configured for legacy IDE mode, IRQ14 and IRQ15 are expected to behave as ISA legacy interrupts, which cannot be shared, i.e. through the Serial Interrupt pin. If IRQ14 and IRQ15 are shared with Serial Interrupt pin then abnormal system behavior may occur. For example, IRQ14/15 may not be detected by ICH9's interrupt controller. When the SATA controller is not running in Native IDE mode, IRQ14 and IRQ15 are used as special interrupts. If the SATA controller is in native modes, these interrupts can be mapped to other devices accordingly. 5.10.1 Start Frame The serial IRQ protocol has two modes of operation which affect the start frame. These two modes are: Continuous, where the ICH9 is solely responsible for generating the start frame; and Quiet, where a serial IRQ peripheral is responsible for beginning the start frame. The mode that must first be entered when enabling the serial IRQ protocol is continuous mode. In this mode, the ICH9 asserts the start frame. This start frame is 4, 6, or 8 PCI clocks wide based upon the Serial IRQ Control Register, bits 1:0 at 64h in Device 31:Function 0 configuration space. This is a polling mode. When the serial IRQ stream enters quiet mode (signaled in the Stop Frame), the SERIRQ line remains inactive and pulled up between the Stop and Start Frame until a peripheral drives the SERIRQ signal low. The ICH9 senses the line low and continues to drive it low for the remainder of the Start Frame. Since the first PCI clock of the start frame was driven by the peripheral in this mode, the ICH9 drives the SERIRQ line low for 1 PCI clock less than in continuous mode. This mode of operation allows for a quiet, and therefore lower power, operation. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 149 Functional Description 5.10.2 Data Frames Once the Start frame has been initiated, all of the SERIRQ peripherals must start counting frames based on the rising edge of SERIRQ. Each of the IRQ/DATA frames has exactly 3 phases of 1 clock each: • Sample Phase. During this phase, the SERIRQ device drives SERIRQ low if the corresponding interrupt signal is low. If the corresponding interrupt is high, then the SERIRQ devices tri-state the SERIRQ signal. The SERIRQ line remains high due to pull-up resistors (there is no internal pull-up resistor on this signal, an external pull-up resistor is required). A low level during the IRQ0–1 and IRQ2–15 frames indicates that an active-high ISA interrupt is not being requested, but a low level during the PCI INT[A:D], SMI#, and IOCHK# frame indicates that an active-low interrupt is being requested. • Recovery Phase. During this phase, the device drives the SERIRQ line high if in the Sample Phase it was driven low. If it was not driven in the sample phase, it is tri-stated in this phase. • Turn-around Phase. The device tri-states the SERIRQ line 5.10.3 Stop Frame After all data frames, a Stop Frame is driven by the ICH9. The SERIRQ signal is driven low by the ICH9 for 2 or 3 PCI clocks. The number of clocks is determined by the SERIRQ configuration register. The number of clocks determines the next mode: Table 5-19. Stop Frame Explanation Stop Frame Width 5.10.4 Next Mode 2 PCI clocks Quiet Mode. Any SERIRQ device may initiate a Start Frame 3 PCI clocks Continuous Mode. Only the host (Intel® ICH9) may initiate a Start Frame Specific Interrupts Not Supported via SERIRQ There are three interrupts seen through the serial stream that are not supported by the ICH9. These interrupts are generated internally, and are not sharable with other devices within the system. These interrupts are: • IRQ0. Heartbeat interrupt generated off of the internal 8254 counter 0. • IRQ8#. RTC interrupt can only be generated internally. • IRQ13. Floating point error interrupt generated off of the processor assertion of FERR#. The ICH9 ignores the state of these interrupts in the serial stream, and does not adjust their level based on the level seen in the serial stream. 150 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.10.5 Data Frame Format Table 5-20 shows the format of the data frames. For the PCI interrupts (A–D), the output from the ICH9 is AND’d with the PCI input signal. This way, the interrupt can be signaled via both the PCI interrupt input signal and via the SERIRQ signal (they are shared). Table 5-20. Data Frame Format Data Frame # Interrupt Clocks Past Start Frame 1 IRQ0 2 2 IRQ1 5 3 SMI# 8 4 IRQ3 11 5 IRQ4 14 6 IRQ5 17 7 IRQ6 20 8 IRQ7 23 9 IRQ8 26 10 IRQ9 29 11 IRQ10 32 12 IRQ11 35 13 IRQ12 38 14 IRQ13 41 Ignored. IRQ13 can only be generated from FERR# 15 IRQ14 44 Not attached to SATA logic 16 IRQ15 47 Not attached to SATA logic 17 IOCHCK# 50 Same as ISA IOCHCK# going active. 18 PCI INTA# 53 Drive PIRQA# 19 PCI INTB# 56 Drive PIRQB# 20 PCI INTC# 59 Drive PIRQC# 21 PCI INTD# 62 Drive PIRQD# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Comment Ignored. IRQ0 can only be generated via the internal 8524 Causes SMI# if low. Will set the SERIRQ_SMI_STS bit. Ignored. IRQ8# can only be generated internally. 151 Functional Description 5.11 Real Time Clock (D31:F0) The Real Time Clock (RTC) module provides a battery backed-up date and time keeping device with two banks of static RAM with 128 bytes each, although the first bank has 114 bytes for general purpose usage. Three interrupt features are available: time of day alarm with once a second to once a month range, periodic rates of 122 µs to 500 ms, and end of update cycle notification. Seconds, minutes, hours, days, day of week, month, and year are counted. Daylight savings compensation is no longer supported. The hour is represented in twelve or twenty-four hour format, and data can be represented in BCD or binary format. The design is functionally compatible with the Motorola MS146818B. The time keeping comes from a 32.768 kHz oscillating source, which is divided to achieve an update every second. The lower 14 bytes on the lower RAM block has very specific functions. The first ten are for time and date information. The next four (0Ah to 0Dh) are registers, which configure and report RTC functions. The time and calendar data should match the data mode (BCD or binary) and hour mode (12 or 24 hour) as selected in register B. It is up to the programmer to make sure that data stored in these locations is within the reasonable values ranges and represents a possible date and time. The exception to these ranges is to store a value of C0–FFh in the Alarm bytes to indicate a don’t care situation. All Alarm conditions must match to trigger an Alarm Flag, which could trigger an Alarm Interrupt if enabled. The SET bit must be 1 while programming these locations to avoid clashes with an update cycle. Access to time and date information is done through the RAM locations. If a RAM read from the ten time and date bytes is attempted during an update cycle, the value read do not necessarily represent the true contents of those locations. Any RAM writes under the same conditions are ignored. Note: The leap year determination for adding a 29th day to February does not take into account the end-of-the-century exceptions. The logic simply assumes that all years divisible by 4 are leap years. According to the Royal Observatory Greenwich, years that are divisible by 100 are typically not leap years. In every fourth century (years divisible by 400, like 2000), the 100-year-exception is over-ridden and a leap-year occurs. Note that the year 2100 will be the first time in which the current RTC implementation would incorrectly calculate the leap-year. The ICH9 does not implement month/year alarms. 5.11.1 Update Cycles An update cycle occurs once a second, if the SET bit of register B is not asserted and the divide chain is properly configured. During this procedure, the stored time and date are incremented, overflow is checked, a matching alarm condition is checked, and the time and date are rewritten to the RAM locations. The update cycle will start at least 488 µs after the UIP bit of register A is asserted, and the entire cycle does not take more than 1984 µs to complete. The time and date RAM locations (0–9) are disconnected from the external bus during this time. To avoid update and data corruption conditions, external RAM access to these locations can safely occur at two times. When a updated-ended interrupt is detected, almost 999 ms is available to read and write the valid time and date data. If the UIP bit of Register A is detected to be low, there is at least 488 µs before the update cycle begins. Warning: 152 The overflow conditions for leap years adjustments are based on more than one date or time item. To ensure proper operation when adjusting the time, the new time and data values should be set at least two seconds before leap year occurs. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.11.2 Interrupts The real-time clock interrupt is internally routed within the ICH9 both to the I/O APIC and the 8259. It is mapped to interrupt vector 8. This interrupt does not leave the ICH9, nor is it shared with any other interrupt. IRQ8# from the SERIRQ stream is ignored. However, the High Performance Event Timers can also be mapped to IRQ8#; in this case, the RTC interrupt is blocked. 5.11.3 Lockable RAM Ranges The RTC’s battery-backed RAM supports two 8-byte ranges that can be locked via the configuration space. If the locking bits are set, the corresponding range in the RAM will not be readable or writable. A write cycle to those locations will have no effect. A read cycle to those locations will not return the location’s actual value (resultant value is undefined). Once a range is locked, the range can be unlocked only by a hard reset, which will invoke the BIOS and allow it to relock the RAM range. 5.11.4 Century Rollover The ICH9 detects a rollover when the Year byte (RTC I/O space, index offset 09h) transitions form 99 to 00. Upon detecting the rollover, the ICH9 sets the NEWCENTURY_STS bit (TCOBASE + 04h, bit 7). If the system is in an S0 state, this causes an SMI#. The SMI# handler can update registers in the RTC RAM that are associated with century value. If the system is in a sleep state (S1–S5) when the century rollover occurs, the ICH9 also sets the NEWCENTURY_STS bit, but no SMI# is generated. When the system resumes from the sleep state, BIOS should check the NEWCENTURY_STS bit and update the century value in the RTC RAM. 5.11.5 Clearing Battery-Backed RTC RAM Clearing CMOS RAM in an ICH9-based platform can be done by using a jumper on RTCRST# or GPI. Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. Using RTCRST# to Clear CMOS A jumper on RTCRST# can be used to clear CMOS values, as well as reset to default, the state of those configuration bits that reside in the RTC power well. When the RTCRST# is strapped to ground, the RTC_PWR_STS bit (D31:F0:A4h bit 2) will be set and those configuration bits in the RTC power well will be set to their default state. BIOS can monitor the state of this bit, and manually clear the RTC CMOS array once the system is booted. The normal position would cause RTCRST# to be pulled up through a weak pull-up resistor. Table 5-21 shows which bits are set to their default state when RTCRST# is asserted. This RTCRST# jumper technique allows the jumper to be moved and then replaced—all while the system is powered off. Then, once booted, the RTC_PWR_STS can be detected in the set state. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 153 Functional Description Table 5-21. Configuration Bits Reset by RTCRST# Assertion (Sheet 1 of 2) Bit Name 154 Register Location Bit(s) Default State Alarm Interrupt Enable (AIE) Register B (General Configuration) (RTC_REGB) I/O space (RTC Index + 0Bh) 5 X Alarm Flag (AF) Register C (Flag Register) (RTC_REGC) I/O space (RTC Index + 0Ch) 5 X SWSMI_RATE_SEL General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 7:6 0 SLP_S4# Minimum Assertion Width General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 5:4 0 SLP_S4# Assertion Stretch Enable General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 3 0 RTC Power Status (RTC_PWR_STS) General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 2 0 Power Failure (PWR_FLR) General PM Configuration 3 Register (GEN_PMCON_3) D31:F0:A4h 1 0 AFTERG3_EN General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 0 0 Power Button Override Status (PWRBTNOR_STS) Power Management 1 Status Register (PM1_STS) PMBase + 00h 11 0 RTC Event Enable (RTC_EN) Power Management 1 Enable Register (PM1_EN) PMBase + 02h 10 0 Sleep Type (SLP_TYP) Power Management 1 Control (PM1_CNT) PMBase + 04h 12:10 0 PME_EN General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch 11 0 BATLOW_EN (Mobile Only) General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch 10 0 RI_EN General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch 8 0 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-21. Configuration Bits Reset by RTCRST# Assertion (Sheet 2 of 2) Bit Name Register Location Bit(s) Default State NEWCENTURY_STS TCO1 Status Register (TCO1_STS) TCOBase + 04h 7 0 Intruder Detect (INTRD_DET) TCO2 Status Register (TCO2_STS) TCOBase + 06h 0 0 Top Swap (TS) Backed Up Control Register (BUC) Chipset Config Registers:Offset 3414h 0 X Using a GPI to Clear CMOS A jumper on a GPI can also be used to clear CMOS values. BIOS would detect the setting of this GPI on system boot-up, and manually clear the CMOS array. Note: The GPI strap technique to clear CMOS requires multiple steps to implement. The system is booted with the jumper in new position, then powered back down. The jumper is replaced back to the normal position, then the system is rebooted again. Warning: Clearing CMOS, using a jumper on VccRTC, must not be implemented. 5.12 Processor Interface (D31:F0) The ICH9 interfaces to the processor with a variety of signals • Standard Outputs to processor: A20M#, SMI#, NMI, INIT#, INTR, STPCLK#, IGNNE#, CPUPWRGD, DPSLP# (Mobile Only) • Standard Input from processor: FERR#, THRMTRIP# • Intel SpeedStep® technology output to processor: CPUPWRGD (Mobile Only) Most ICH9 outputs to the processor use standard buffers. The ICH9 has separate V_CPU_IO signals that are pulled up at the system level to the processor voltage, and thus determines VOH for the outputs to the processor. 5.12.1 Processor Interface Signals This section describes each of the signals that interface between the ICH9 and the processor(s). Note that the behavior of some signals may vary during processor reset, as the signals are used for frequency strapping. 5.12.1.1 A20M# (Mask A20) The A20M# signal is active (low) when both of the following conditions are true: • The ALT_A20_GATE bit (Bit 1 of PORT92 register) is a 0 • The A20GATE input signal is a 0 The A20GATE input signal is expected to be generated by the external microcontroller (KBC). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 155 Functional Description 5.12.1.2 INIT# (Initialization) The INIT# signal is active (driven low) based on any one of several events described in Table 5-22. When any of these events occur, INIT# is driven low for 16 PCI clocks, then driven high. Note: The 16-clock counter for INIT# assertion halts while STPCLK# is active. Therefore, if INIT# is supposed to go active while STPCLK# is asserted, it actually goes active after STPCLK# goes inactive. This section refers to INIT#, but applies to two signals: INIT# and INIT3_3V# (Desktop Only), as INIT3_3V# (Desktop Only) is functionally identical to INIT#, but signaling at 3.3 V. Table 5-22. INIT# Going Active Cause of INIT# Going Active Shutdown special cycle from processor observed on ICH-GMCH interconnect (from GMCH). Comment INIT# assertion based on value of Shutdown Policy Select register (SPS) PORT92 write, where INIT_NOW (bit 0) transitions from a 0 to a 1. PORTCF9 write, where SYS_RST (bit 1) was a 0 and RST_CPU (bit 2) transitions from 0 to 1. 5.12.1.3 RCIN# input signal goes low. RCIN# is expected to be driven by the external microcontroller (KBC). 0 to 1 transition on RCIN# must occur before the Intel® ICH9 will arm INIT# to be generated again. NOTE: RCIN# signal is expected to be low during S3, S4, and S5 states. Transition on the RCIN# signal in those states (or the transition to those states) may not necessarily cause the INIT# signal to be generated to the processor. CPU BIST To enter BIST, software sets CPU_BIST_EN bit and then does a full processor reset using the CF9 register. FERR#/IGNNE# (Numeric Coprocessor Error/ Ignore Numeric Error) The ICH9 supports the coprocessor error function with the FERR#/IGNNE# pins. The function is enabled via the COPROC_ERR_EN bit (Chipset Config Registers:Offset 31FFh:bit 1). FERR# is tied directly to the Coprocessor Error signal of the processor. If FERR# is driven active by the processor, IRQ13 goes active (internally). When it detects a write to the COPROC_ERR register (I/O Register F0h), the ICH9 negates the internal IRQ13 and drives IGNNE# active. IGNNE# remains active until FERR# is driven inactive. IGNNE# is never driven active unless FERR# is active. 156 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Figure 5-5. Coprocessor Error Timing Diagram FERR# Internal IRQ13 I/O Write to F0h IGNNE# If COPROC_ERR_EN is not set, the assertion of FERR# will not generate an internal IRQ13, nor will the write to F0h generate IGNNE#. 5.12.1.4 NMI (Non-Maskable Interrupt) Non-Maskable Interrupts (NMIs) can be generated by several sources, as described in Table 5-23. Table 5-23. NMI Sources Cause of NMI 5.12.1.5 Comment SERR# goes active (either internally, externally via SERR# signal, or via message from (G)MCH) Can instead be routed to generate an SCI, through the NMI2SCI_EN bit (Device 31:Function 0, TCO Base + 08h, bit 11). IOCHK# goes active via SERIRQ# stream (ISA system Error) Can instead be routed to generate an SCI, through the NMI2SCI_EN bit (Device 31:Function 0, TCO Base + 08h, bit 11). Stop Clock Request (STPCLK#) The ICH9 power management logic controls this active-low signal. Refer to Section 5.13 for more information on the functionality of this signal. 5.12.1.6 CPU Power Good (CPUPWRGD) This signal is connected to the processor’s PWRGOOD input. This signal represents a logical AND of the ICH9’s PWROK and VRMPWRGD signals. 5.12.1.7 Deeper Sleep (DPSLP#) (Mobile Only) This active-low signal controls the internal gating of the processor’s core clock. This signal asserts before and deasserts after the STP_CPU# signal to effectively stop the processor’s clock (internally) in the states in which STP_CPU# can be used to stop the processor’s clock externally. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 157 Functional Description 5.12.2 Dual-Processor Issues (Desktop Only) 5.12.2.1 Signal Differences In dual-processor designs, some of the processor signals are unused or used differently than for uniprocessor designs. Table 5-24. DP Signal Differences Signal A20M# / A20GATE Difference Generally not used, but still supported by Intel® ICH9. Used for S1 State as well as preparation for entry to S3–S5 5.12.2.2 STPCLK# Also allows for THERM# based throttling (not via ACPI control methods). Should be connected to both processors. FERR# / IGNNE# Generally not used, but still supported by ICH9. Power Management For multiple-processor (or Multiple-core) configurations in which more than one Stop Grant cycle may be generated, the (G)MCH is expected to count Stop Grant cycles and only pass the last one through to the ICH9. This prevents the ICH9 from getting out of sync with the processor on multiple STPCLK# assertions. Because the S1 state will have the STPCLK# signal active, the STPCLK# signal can be connected to both processors. However, for ACPI implementations, the BIOS must indicate that the ICH9 only supports the C1 state for dual-processor designs. In going to the S1 state for desktop, multiple Stop-Grant cycles will be generated by the processors. It is assumed that prior to setting the SLP_EN bit (which causes the transition to the S1 state), the processors will not be executing code that is likely to delay the Stop-Grant cycles. In going to the S3, S4, or S5 states, the system will appear to pass through the S1 state; thus, STPCLK# and SLP# are also used. During the S3, S4, and S5 states, both processors will lose power. Upon exit from those states, the processors will have their power restored. 158 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13 Power Management (D31:F0) 5.13.1 Features • Support for Advanced Configuration and Power Interface, Version 3.0a (ACPI) providing power and thermal management — ACPI 24-Bit Timer — Software initiated throttling of processor performance for Thermal and Power Reduction — Hardware Override to throttle processor performance if system too hot — SCI and SMI# Generation — ACPI C2 state Stop-Grant state (using STPCLK# signal) halts processor’s instruction stream • PCI PME# signal for Wake Up from Low-Power states • System Clock Control — (Mobile Only) ACPI C3 State: Ability to halt processor clock (but not memory clock) — (Mobile Only) ACPI C4 State: Ability to lower processor voltage. — (Mobile Only) CLKRUN# Protocol for PCI Clock Starting/Stopping • System Sleep State Control — ACPI S1 state: Stop Grant (using STPCLK# signal) halts processor’s instruction stream (only STPCLK# active) — ACPI S3 state — Suspend to RAM (STR) — ACPI S4 state — Suspend-to-Disk (STD) — ACPI G2/S5 state — Soft Off (SOFF) — Power Failure Detection and Recovery • Management Engine Power Management Support — New Wake events from the Management Engine (enabled from all S-States including Catastrophic S5 conditions) • Streamlined Legacy Power Management for APM-Based Systems 5.13.2 Intel® ICH9 and System Power States Table 5-25 shows the power states defined for ICH9-based platforms. The state names generally match the corresponding ACPI states. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 159 Functional Description Table 5-25. General Power States for Systems Using Intel® ICH9 State/ Substates Legacy Name / Description G0/S0/C0 Full On: Processor operating. Individual devices may be shut down to save power. The different processor operating levels are defined by Cx states, as shown in Table 5-26. Within the C0 state, the Intel® ICH9 can throttle the processor using the STPCLK# signal to reduce power consumption. The throttling can be initiated by software or by the operating system or BIOS. G0/S0/C1 Auto-Halt: Processor has executed an AutoHalt instruction and is not executing code. The processor snoops the bus and maintains cache coherency. G0/S0/C2 Stop-Grant: The STPCLK# signal goes active to the processor. The processor performs a Stop-Grant cycle, halts its instruction stream, and remains in that state until the STPCLK# signal goes inactive. In the Stop-Grant state, the processor snoops the bus and maintains cache coherency. G0/S0/C3 (Mobile Only) Stop-Clock: The STPCLK# signal goes active to the processor. The processor performs a Stop-Grant cycle, halts its instruction stream. ICH9 then asserts DPSLP# followed by STP_CPU#, which forces the clock generator to stop the processor clock. This is also used for Intel SpeedStep® technology support. Accesses to memory (by graphics, PCI, or internal units) is not permitted while in a C3 state. G0/S0/C4 (Mobile Only) Stop-Clock with Lower Processor Voltage: This closely resembles the G0/ S0/C3 state. However, after the ICH9 has asserted STP_CPU#, it then lowers the voltage to the processor. This reduces the leakage on the processor. Prior to exiting the C4 state, the ICH9 increases the voltage to the processor. G0/S0/C5 (Mobile Only) Stop-Clock with Very Low Processor Voltage and Cache Flush: The processor voltage is dropped to the minimum level needed to maintain the state. Caches are flushed from the processor to main memory prior to entering C5, allowing bus master activity while in C5. G0/S0/C6 (Mobile Only) Stop-Clock with Partially Processor Power Down and Cache Flush: C6 includes a cache flush as in C5. The processor saves internal state to RAM allowing the processor to partially turn off. Stop-Grant: Similar to G0/S0/C2 state. G1/S1 160 Note: The behavior for this state is slightly different when supporting Intel® 64 processors. G1/S3 Suspend-To-RAM (STR): The system context is maintained in system DRAM, but power is shut off to non-critical circuits. Memory is retained, and refreshes continue. All clocks stop except RTC clock. G1/S4 Suspend-To-Disk (STD): The context of the system is maintained on the disk. All power is then shut off to the system except for the logic required to resume. G2/S5 Soft Off (SOFF): System context is not maintained. All power is shut off except for the logic required to restart. A full boot is required when waking. G3 Mechanical OFF (MOFF): System context not maintained. All power is shut off except for the RTC. No “Wake” events are possible, because the system does not have any power. This state occurs if the user removes the batteries, turns off a mechanical switch, or if the system power supply is at a level that is insufficient to power the “waking” logic. When system power returns, transition will depend on the state just prior to the entry to G3 and the AFTERG3 _EN bit in the GEN_PMCON3 register (D31:F0, offset A4). Refer to Table 5-33 for more details. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-26 shows the transitions rules among the various states. Note that transitions among the various states may appear to temporarily transition through intermediate states. For example, in going from S0 to S1, it may appear to pass through the G0/S0/ C2 states. These intermediate transitions and states are not listed in the table. Table 5-26. State Transition Rules for Intel® ICH9 Present State Transition Trigger Next State • • • • • • • Processor halt instruction Level 2 Read Level 3 Read (Mobile Only) Level 4 Read (Mobile Only) SLP_EN bit set Power Button Override Mechanical Off/Power Failure • • • • • • G0/S0/C1 G0/S0/C2 G0/S0/C2, G0/S0/C3 or G0/S0/C4 - depending on C4onC3_EN bit (D31:F0:Offset A0h:bit 7) and BM_STS_ZERO_EN bit (D31:F0:Offset A9h:bit 2) (Mobile Only) G1/Sx or G2/S5 state G2/S5 G3 • • • • Any Enabled Break Event STPCLK# goes active Power Button Override Power Failure • • • • G0/S0/C0 G0/S0/C2 G2/S5 G3 • • • • Any Enabled Break Event Power Button Override Power Failure Previously in C3/C4 and bus masters idle • • • • G0/S0/C0 G2/S5 G3 C3 or C4 - depending on PDME bit (D31:F0: Offset A9h: bit 4) • • Any Enabled Break Event Any Bus Master Event • • • • • Power Button Override Power Failure Previously in C4 and bus masters idle • • • G0/S0/C0 G0/S0/C2 - if PUME bit (D31:F0: Offset A9h: bit 3) is set, else G0/S0/C0 G2/S5 G3 C4 - depending on PDME bit (D31:F0: Offset A9h: bit 4 G0/S0/C4 (Mobile Only) • • • • Any Enabled Break Event Any Bus Master Event Power Button Override Power Failure • • • • G0/S0/C0 G0/S0/C2 - if PUME bit (D31:F0: Offset A9h: bit 3) is set, else G0/S0/C0 G2/S5 G3 G0/S0/C5 (Mobile Only) • • • • Any Enabled Break Event Any Bus Master Event Power Button Override Power Failure • • • • G0/S0/C0 C5 G2/S5 G3 G0/S0/C6 (Mobile Only) • • • • Any Enabled Break Event Any Bus Master Event Power Button Override Power Failure • • • • G0/S0/C0 G6 G2/S5 G3 G1/S1, G1/S3, or G1/S4 • • • Any Enabled Wake Event Power Button Override Power Failure • • • G0/S0/C0 (See Note 2) G2/S5 G3 G2/S5 • • Any Enabled Wake Event Power Failure • • G0/S0/C0 (See Note 2) G3 • Power Returns • Optional to go to S0/C0 (reboot) or G2/S5 (stay off until power button pressed or other wake event). (See Note 1 and 2) G0/S0/C0 G0/S0/C1 G0/S0/C2 G0/S0/C3 (Mobile Only) G3 NOTES: 1. Some wake events can be preserved through power failure. 2. Transitions from the S1–S5 or G3 states to the S0 state are deferred until BATLOW# is inactive in mobile configurations. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 161 Functional Description 5.13.3 System Power Planes The system has several independent power planes, as described in Table 5-27. Note that when a particular power plane is shut off, it should go to a 0 V level. s Table 5-27. System Power Plane Plane Controlled By Description CPU SLP_S3# signal The SLP_S3# signal can be used to cut the power to the processor completely. For Mobile systems, the DPRSLPVR support allows lowering the processor’s voltage during the C4 state. MAIN MEMORY 5.13.4 SLP_S3# signal SLP_S4# signal SLP_S5# signal Link Controller SLP_M# DEVICE[n] GPIO When SLP_S3# goes active, power can be shut off to any circuit not required to wake the system from the S3 state. Since the S3 state requires that the memory context be preserved, power must be retained to the main memory. The processor, devices on the PCI bus, LPC I/F, and graphics will typically be shut off when the Main power plane is shut, although there may be small subsections powered. When the SLP_S4# goes active, power can be shut off to any circuit not required to wake the system from the S4. Since the memory context does not need to be preserved in the S4 state, the power to the memory can also be shut down. When SLP_S5# goes active, power can be shut to any circuit not required to wake the system from the S5 state. Since the memory context does not need to be preserved in the S5 state, the power to the memory can also be shut. This pin is asserted when the manageability platform goes to MOff. Depending on the platform, this pin may be used to control the MCH, ICH controller link power planes, the clock chip power, and the SPI flash power. Individual subsystems may have their own power plane. For example, GPIO signals may be used to control the power to disk drives, audio amplifiers, or the display screen. SMI#/SCI Generation On any SMI# event taking place, ICH9 asserts SMI# to the processor, which causes it to enter SMM space. SMI# remains active until the EOS bit is set. When the EOS bit is set, SMI# goes inactive for a minimum of 4 PCI clocks. If another SMI event occurs, SMI# is driven active again. The SCI is a level-mode interrupt that is typically handled by an ACPI-aware operating system. In non-APIC systems (which is the default), the SCI IRQ is routed to one of the 8259 interrupts (IRQ 9, 10, or 11). The 8259 interrupt controller must be programmed to level mode for that interrupt. In systems using the APIC, the SCI can be routed to interrupts 9, 10, 11, 20, 21, 22, or 23. The interrupt polarity changes depending on whether it is on an interrupt shareable with a PIRQ or not (see Section 13.1.3). The interrupt remains asserted until all SCI sources are removed. Table 5-28 shows which events can cause an SMI# and SCI. Note that some events can be programmed to cause either an SMI# or SCI. The usage of the event for SCI (instead of SMI#) is typically associated with an ACPI-based system. Each SMI# or SCI source has a corresponding enable and status bit. 162 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-28. Causes of SMI# and SCI (Sheet 1 of 2) Cause SW Generated GPE SCI Yes SMI Additional Enables Where Reported Yes SWGPE_EN=1 SWGPE_STS SPI_STS SPI Command Completed No Yes FSMIE (See SPI Hardware Sequencing Flash Control Register) PME# Yes Yes PME_EN=1 PME_STS PME_B0 (Internal, Bus 0, PME-Capable Agents) Yes Yes PME_B0_EN=1 PME_B0_STS PCI Express* PME Messages Yes Yes PCI Express Hot Plug Message Yes Yes Power Button Press Yes Yes PWRBTN_EN=1 PWRBTN_STS Power Button Override (Note 7) Yes No None PWRBTNOR_STS PCI_EXP_EN=1 (Not enabled for SMI) HOT_PLUG_EN=1 (Not enabled for SMI) PCI_EXP_STS HOT_PLUG_STS RTC Alarm Yes Yes RTC_EN=1 RTC_STS Ring Indicate Yes Yes RI_EN=1 RI_STS USB#1 wakes Yes Yes USB1_EN=1 USB1_STS USB#2 wakes Yes Yes USB2_EN=1 USB2_STS USB#3 wakes Yes Yes USB3_EN=1 USB3_STS USB#4 wakes Yes Yes USB4_EN=1 USB4_STS USB#5 wakes Yes Yes USB5_EN=1 USB5_STS USB#6 wakes Yes Yes USB6_EN=1 USB6_STS THRM# pin active Yes Yes THRM_EN=1 THRM_STS ACPI Timer overflow (2.34 sec.) Yes Yes TMROF_EN=1 TMROF_STS Any GPI Yes Yes GPI[x]_Route=10 (SCI) GPI[x]_Route=01 (SMI) GPE0[x]_EN=1 TCO SCI Logic Yes No TCOSCI_EN=1 TCOSCI_STS TCO SCI message from (G)MCH Yes No none MCHSCI_STS TCO SMI Logic No Yes TCO_EN=1 TCO_STS TCO SMI — Year 2000 Rollover No Yes none NEWCENTURY_STS TCO SMI — TCO TIMEROUT No Yes none TIMEOUT TCO SMI — OS writes to TCO_DAT_IN register No Yes none OS_TCO_SMI TCO SMI — Message from (G)MCH No Yes none MCHSMI_STS TCO SMI — NMI occurred (and NMIs mapped to SMI) No Yes NMI2SMI_EN=1 NMI2SMI_STS TCO SMI — INTRUDER# signal goes active No Yes INTRD_SEL=10 INTRD_DET TCO SMI — Change of the BIOSWE bit from 0 to 1 No Yes BC.LE=1 BIOSWR_STS Intel® I/O Controller Hub 9 (ICH9) Family Datasheet GPI[x]_STS GPE0_STS 163 Functional Description Table 5-28. Causes of SMI# and SCI (Sheet 2 of 2) Cause SCI SMI Additional Enables Where Reported TCO SMI — Write attempted to BIOS No Yes BIOSWE=1 BIOSWR_STS BIOS_RLS written to Yes No GBL_EN=1 GBL_STS GBL_RLS written to No Yes BIOS_EN=1 BIOS_STS Write to B2h register No Yes APMC_EN = 1 APM_STS Periodic timer expires No Yes PERIODIC_EN=1 PERIODIC_STS 64 ms timer expires No Yes SWSMI_TMR_EN=1 SWSMI_TMR_STS Enhanced USB Legacy Support Event No Yes LEGACY_USB2_EN = 1 LEGACY_USB2_STS Enhanced USB Intel Specific Event No Yes INTEL_USB2_EN = 1 INTEL_USB2_STS UHCI USB Legacy logic No Yes LEGACY_USB_EN=1 LEGACY_USB_STS Serial IRQ SMI reported No Yes none SERIRQ_SMI_STS Device monitors match address in its range No Yes none DEVMON_STS, DEVACT_STS SMBus Host Controller No Yes SMB_SMI_EN Host Controller Enabled SMBus host status reg. SMBus Slave SMI message No Yes none SMBUS_SMI_STS SMBus SMBALERT# signal active No Yes none SMBUS_SMI_STS SMBus Host Notify message received No Yes HOST_NOTIFY_INTRE N SMBUS_SMI_STS HOST_NOTIFY_STS (Mobile Only) BATLOW# assertion Yes Yes BATLOW_EN=1. BATLOW_STS Access microcontroller 62h/ 66h No Yes MCSMI_EN MCSMI_STS SLP_EN bit written to 1 No Yes SMI_ON_SLP_EN=1 SMI_ON_SLP_EN_STS USB2_STS, Write Enable Status USB Per-Port Registers Write Enable bit changes to 1. No Yes USB2_EN=1, Write_Enable_SMI_En able=1 Write attempted to BIOS No Yes BIOSWE = 0 BIOSWR_STS GPIO Lockdown Enable bit changes from ‘1’ to ‘0’. No Yes GPIO_UNLOCK_SMI_E N=1 GPIO_UNLOCK_SMI_S TS NOTES: 1. SCI_EN must be 1 to enable SCI. SCI_EN must be 0 to enable SMI. 2. SCI can be routed to cause interrupt 9:11 or 20:23 (20:23 only available in APIC mode). 3. GBL_SMI_EN must be 1 to enable SMI. 4. EOS must be written to 1 to re-enable SMI for the next 1. 5. ICH9 must have SMI# fully enabled when ICH9 is also enabled to trap cycles. If SMI# is not enabled in conjunction with the trap enabling, then hardware behavior is undefined. 6. Only GPI[15:0] may generate an SMI# or SCI. 7. When a power button override first occurs, the system will transition immediately to S5. The SCI will only occur after the next wake to S0 if the residual status bit (PWRBTNOR_STS) is not cleared prior to setting SCI_EN. 164 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.4.1 PCI Express* SCI PCI Express ports and the (G)MCH (via DMI) have the ability to cause PME using messages. When a PME message is received, ICH9 will set the PCI_EXP_STS bit. If the PCI_EXP_EN bit is also set, the ICH9 can cause an SCI via the GPE1_STS register. 5.13.4.2 PCI Express* Hot-Plug PCI Express has a Hot-Plug mechanism and is capable of generating a SCI via the GPE1 register. It is also capable of generating an SMI. However, it is not capable of generating a wake event. 5.13.5 Dynamic Processor Clock Control The ICH9 has extensive control for dynamically starting and stopping system clocks. The clock control is used for transitions among the various S0/Cx states, and processor throttling. Each dynamic clock control method is described in this section. The various sleep states may also perform types of non-dynamic clock control. The ICH9 supports the ACPI C0, C1 and C2 states (in desktop) or C0, C1, C2, C3, C4, C5 and C6 (in mobile) states. The Dynamic Processor Clock control is handled using the following signals: • STPCLK#: Used to halt processor instruction stream. • (Mobile Only) STP_CPU#: Used to stop processor’s clock • (Mobile Only) DPSLP#: Used to force Deeper Sleep for processor. • (Mobile Only) DPRSLPVR: Used to lower voltage of VRM during C4 state. • (Mobile Only) DPRSTP#: Used to alert the processor of C4 state. Also works in conjunction with DPRSLPVR to communicate to the VRM whether a slow or fast voltage ramp should be used. The C1 state is entered based on the processor performing an auto halt instruction. The C2 state is entered based on the processor reading the Level 2 register in the ICH9. (Mobile Only) The C2 state can also be entered from C3 or C4 states if bus masters require snoops and the PUME bit (D31:F0: Offset A9h: bit 3) is set. (Mobile Only) The C3 state is entered based on the processor reading the Level 3 register in the ICH9 and when the C4onC3_EN bit is clear (D31:F0:Offset A0:bit 7). This state can also be entered after a temporary return to C2 from a prior C3 or C4 state. (Mobile Only) The C4 state is entered based on the processor reading the Level 4 register in the ICH9, or by reading the Level 3 register when the C4onC3_EN bit is set. This state can also be entered after a temporary return to C2 from a prior C4 state. (Mobile Only) The C5 or C6 state is entered based on the processor reading the Level 5 or Level 6 register in the ICH9 or the processor sending the stop grant message. Note: The ICH uses the same flow for both C5 and C6 states. The platform must only support one or the other since the programmable exit timers for C5 and C6 are different, and the flow uses the same timers for both which are statically configured. A C1 or C2 state in desktop or a C1, C2, C3, C4, C5 or C6 state in mobile ends due to a Break event. Based on the break event, the ICH9 returns the system to C0 state. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 165 Functional Description Table 5-29 lists the possible break events from C2, C3, C4, C5 or C6. The break events from C1 are indicated in the processor’s datasheet. The break events for C3, C4, C5 and C6 are Mobile Only. Table 5-29. Break Events Breaks from Comment Any unmasked interrupt goes active C2, C3, C4, C5, C6 IRQ[0:15] when using the 8259s, IRQ[0:23] for I/O APIC. Since SCI is an interrupt, any SCI will also be a break event. Any internal event that cause an NMI or SMI# C2, C3, C4, C5, C6 Many possible sources Any internal event that cause INIT# to go active C2, C3, C4 C5, C6 Could be indicated by the keyboard controller via the RCIN input signal. Event 5.13.5.1 Need to wake up processor so it can do snoops Any bus master request (internal, external or DMA) goes active and BM_RLD=1 (D31:F0:Offset PMBASE+04h: bit 1) C3, C4 Processor Pending Break Event Indication C2, C3, C4 Only available if FERR# enabled for break event indication (See FERR# Mux Enable in GCS, Chipset Config Registers:Offset 3410h:bit 6) REQ-C0 Message from MCH C2, C3, C4, C5, C6 Can be sent at any time after the Ack-C2 message and before the Ack-C0 message, when not in C0 state. Note: If the PUME bit (D31:F0: Offset A9h: bit 3) is set, then bus master activity will NOT be treated as a break event. Instead, there will be a return only to the C2 state. Slow C4 and C5 Exit (Mobile Only) In order to eliminate the audible noise caused by aggressive voltage ramps when exiting C4 or C5 states at a regular, periodic frequency, the ICH9 supports a method to slow down the voltage ramp at the processor VR for certain break events. If enabled for this behavior, the ICH9 treats IRQ0 and IRQ8 as “slow” break events since both of these can be the system timer tick interrupt. Rather than carefully tracking the interrupt and timer configuration information to track the one correct interrupt, it was deemed acceptable to simplify the logic and slow the break exit sequence for both interrupts. Other break event sources invoke the normal exit timings. The ICH9 indicates that a slow voltage ramp is desired by deasserting DPRSTP# (high) and leaving DPRSLPVR asserted (high). The normal voltage ramp rate is communicated by deasserting DPRSTP# (high) and deasserting DPRSLPVR (low). The ICH9 waits an additional delay before starting the normal voltage ramp timer during the C4 or C5 exit sequence. If a “fast” break event occurs during the additional, slow-Exit time delay, the ICH9 quickly deasserts DPRSLPVR (low), thereby speeding up the voltage ramp and reducing the delay to a value that is typically seen by the device in the past. In the event that a fast break event and a slow break event occur together, the fast flow is taken. The ICH9 provides separate enabled for Slow C4 Exit and Slow C5 exit. 166 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.5.2 Transition Rules among S0/Cx and Throttling States The following priority rules and assumptions apply among the various S0/Cx and throttling states: • Entry to any S0/Cx state is mutually exclusive with entry to any S1–S5 state. This is because the processor can only perform one register access at a time and Sleep states have higher priority than thermal throttling. • When the SLP_EN bit is set (system going to a S1–S5 sleep state), the THTL_EN and FORCE_THTL bits can be internally treated as being disabled (no throttling while going to sleep state). • If the THTL_EN or FORCE_THTL bits are set, and a Level 2, Level 3 or Level 4 read then occurs, the system should immediately go and stay in a C2, C3 or C4 state until a break event occurs. A Level 2, Level 3 or Level 4 read has higher priority than the software initiated throttling. C3 and C4 support is Mobile Only. • After an exit from a C2, C3 or C4 state (due to a Break event), and if the THTL_EN or FORCE_THTL bits are still set, the system will continue to throttle STPCLK#. Depending on the time of break event, the first transition on STPCLK# active can be delayed by up to one THRM period (1024 PCI clocks = 30.72 µs). C3 and C4 support is Mobile Only. • The Host controller must post Stop-Grant cycles in such a way that the processor gets an indication of the end of the special cycle prior to the ICH9 observing the Stop-Grant cycle. This ensures that the STPCLK# signals stays active for a sufficient period after the processor observes the response phase. • If in the C1 state and the STPCLK# signal goes active, the processor will generate a Stop-Grant cycle, and the system should go to the C2 state. When STPCLK# goes inactive, it should return to the C1 state. 5.13.5.3 Deferred C3/C4 (Mobile Only) Due to the new DMI protocol, if there is any bus master activity (other than true isochronous), then the C0 to C3 transition will pause at the C2 state. ICH9 will keep the processor in a C2 state until: • ICH9 sees no bus master activity. • A break event occurs. In this case, the ICH9 will perform the C2 to C0 sequence. Note that bus master traffic is not a break event in this case. To take advantage of the Deferred C3/C4 mode, the BM_STS_ZERO_EN bit must be set. This will cause the BM_STS bit to read as 0 even if some bus master activity is present. If this is not done, then the software may avoid even attempting to go to the C3 or C4 state if it sees the BM_STS bit as 1. If the PUME bit (D31:F0: Offset A9h: bit 3) is 0, then the ICH9 will treat bus master activity as a break event. When reaching the C2 state, if there is any bus master activity, the ICH9 will return the processor to a C0 state. 5.13.5.4 POPUP (Auto C3/C4 to C2) (Mobile Only) When the PUME bit (D31:F0: Offset A9h: bit 3) is set, the ICH9 enables a mode of operation where standard (non-isochronous) bus master activity will not be treated as a full break event from the C3 or C4 states. Instead, these will be treated merely as bus master events and return the platform to a C2 state, and thus allow snoops to be performed. After returning to the C2 state, the bus master cycles will be sent to the (G)MCH, even if the ARB_DIS bit is set. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 167 Functional Description 5.13.5.5 POPDOWN (Auto C2 to C3/C4) (Mobile Only) After returning to the C2 state from C3/C4, it the PDME bit (D31:F0: Offset A9h: bit 4) is set, the platform can return to a C3 or C4 state (depending on where it was prior to going back up to C2). This behaves similar to the Deferred C3/C4 transition, and will keep the processor in a C2 state until: • Bus masters are no longer active. • A break event occurs. Note: Bus master traffic is not a break event in this case. 5.13.5.6 C5 and C6 Entry/Exit (Mobile Only) The ICH9 uses the same flow for both C5 and C6 states. However, the platform must only support C5 or C6, since the same programmable exit times used are different, and the timers are shared. The ICH essentially aliases the Level 5 and Level 6 reads together and the Ack_C5 and Ack_C6 messages together. C5/C6 Entry: 1. ICH receives Level 5 Read or Level 6 Read from MCH 2. ICH asserts STPCLK# 3. MCH receives Stop Grant message from processor 4. ICH receives Req C2 message from MCH 5. ICH asserts PMSYNC# to MCH 6. ICH receives Ack_C5 or Ack_C6 message from MCH after MCH has switched to No snoop mode and asserts CPU_SLP. MCH must no send Req_C0 until after it sends Ack_C5 or Ack_C6. 7. ICH asserts DPSLP#, STPCPU#, DPRSTP# and DPRSLPVR signals in sequence based on timer values. 5.13.5.7 C5 Exit (Mobile Only) When the ICH detects a break event after entering C5 due to an internal or external event, it de-asserts DPRSLPVR, DPRSTP#, STPCPU#, DPSLP#, PMSYNC# and STPCLK# signals in sequence based on timer values. The ICH does not attempt to abort the C5 entry sequence if a break event is detected while entering C5. 5.13.6 Dynamic PCI Clock Control (Mobile Only) The PCI clock can be dynamically controlled independent of any other low-power state. This control is accomplished using the CLKRUN# protocol as described in the PCI Mobile Design Guide, and is transparent to software. The Dynamic PCI Clock control is handled using the following signals: • CLKRUN#: Used by PCI and LPC peripherals to request the system PCI clock to run • STP_PCI#: Used to stop the system PCI clock Note: 168 The 33 MHz clock to the ICH9 is “free-running” and is not affected by the STP_PCI# signal. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.6.1 Conditions for Checking the PCI Clock When there is a lack of PCI activity the ICH9 has the capability to stop the PCI clocks to conserve power. “PCI activity” is defined as any activity that would require the PCI clock to be running. Any of the following conditions will indicate that it is not okay to stop the PCI clock: • Cycles on PCI or LPC • Cycles of any internal device that would need to go on the PCI bus • SERIRQ activity Behavioral Description • When there is a lack of activity (as defined above) for 29 PCI clocks, the ICH9 deasserts (drive high) CLKRUN# for 1 clock and then tri-states the signal. 5.13.6.2 Conditions for Maintaining the PCI Clock PCI masters or LPC devices that wish to maintain the PCI clock running will observe the CLKRUN# signal deasserted, and then must re-assert if (drive it low) within 3 clocks. • When the ICH9 has tri-stated the CLKRUN# signal after deasserting it, the ICH9 then checks to see if the signal has been re-asserted (externally). • After observing the CLKRUN# signal asserted for 1 clock, the ICH9 again starts asserting the signal. • If an internal device needs the PCI bus, the ICH9 asserts the CLKRUN# signal. 5.13.6.3 Conditions for Stopping the PCI Clock • If no device re-asserts CLKRUN# once it has been deasserted for at least 6 clocks, the ICH9 stops the PCI clock by asserting the STP_PCI# signal to the clock synthesizer. 5.13.6.4 Conditions for Re-Starting the PCI Clock • A peripheral asserts CLKRUN# to indicate that it needs the PCI clock re-started. • When the ICH9 observes the CLKRUN# signal asserted for 1 (free running) clock, the ICH9 deasserts the STP_PCI# signal to the clock synthesizer within 4 (free running) clocks. • Observing the CLKRUN# signal asserted externally for 1 (free running) clock, the ICH9 again starts driving CLKRUN# asserted. If an internal source requests the clock to be re-started, the ICH9 re-asserts CLKRUN#, and simultaneously deasserts the STP_PCI# signal. 5.13.6.5 LPC Devices and CLKRUN# If an LPC device (of any type) needs the 33 MHz PCI clock, such as for LPC DMA or LPC serial interrupt, then it can assert CLKRUN#. Note that LPC devices running DMA or bus master cycles will not need to assert CLKRUN#, since the ICH9 asserts it on their behalf. The LDRQ# inputs are ignored by the ICH9 when the PCI clock is stopped to the LPC devices in order to avoid misinterpreting the request. The ICH9 assumes that only one more rising PCI clock edge occurs at the LPC device after the assertion of STP_PCI#. Upon deassertion of STP_PCI#, the ICH9 assumes that the LPC device receives its first clock rising edge corresponding to the ICH9’s second PCI clock rising edge after the deassertion. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 169 Functional Description 5.13.7 Sleep States 5.13.7.1 Sleep State Overview The ICH9 directly supports different sleep states (S1–S5), which are entered by setting the SLP_EN bit, or due to a Power Button press. The entry to the Sleep states is based on several assumptions: • Entry to a Cx state is mutually exclusive with entry to a Sleep state. This is because the processor can only perform one register access at a time. A request to Sleep always has higher priority than throttling. • Prior to setting the SLP_EN bit, the software turns off processor-controlled throttling. Note that thermal throttling cannot be disabled, but setting the SLP_EN bit disables thermal throttling (since S1–S5 sleep state has higher priority). • The G3 state cannot be entered via any software mechanism. The G3 state indicates a complete loss of power. 5.13.7.2 Initiating Sleep State Sleep states (S1–S5) are initiated by: • Masking interrupts, turning off all bus master enable bits, setting the desired type in the SLP_TYP field, and then setting the SLP_EN bit. The hardware then attempts to gracefully put the system into the corresponding Sleep state. • Pressing the PWRBTN# Signal for more than 4 seconds to cause a Power Button Override event. In this case the transition to the S5 state is less graceful, since there are no dependencies on observing Stop-Grant cycles from the processor or on clocks other than the RTC clock • Assertion of the THRMTRIP# signal will cause a transition to the S5 state. This can occur when system is in S0 or S1 state. Table 5-30. Sleep Types Sleep Type 5.13.7.3 Comment ® S1 Intel ICH9 asserts the STPCLK# signal. This lowers the processor’s power consumption. No snooping is possible in this state. S3 ICH9 asserts SLP_S3#. The SLP_S3# signal controls the power to non-critical circuits. Power is only retained to devices needed to wake from this sleeping state, as well as to the memory. S4 ICH9 asserts SLP_S3# and SLP_S4#. The SLP_S4# signal shuts off the power to the memory subsystem. Only devices needed to wake from this state should be powered. S5 Same power state as S4. ICH9 asserts SLP_S3#, SLP_S4# and SLP_S5#. Exiting Sleep States Sleep states (S1–S5) are exited based on Wake events. The Wake events forces the system to a full on state (S0), although some non-critical subsystems might still be shut off and have to be brought back manually. For example, the hard disk may be shut off during a sleep state, and have to be enabled via a GPIO pin before it can be used. Upon exit from the ICH9-controlled Sleep states, the WAK_STS bit is set. The possible causes of Wake Events (and their restrictions) are shown in Table 5-31. Note: 170 (Mobile Only) If the BATLOW# signal is asserted, ICH9 does not attempt to wake from an S1–S5 state, even if the power button is pressed. This prevents the system from waking when the battery power is insufficient to wake the system. Wake events that occur while BATLOW# is asserted are latched by the ICH9, and the system wakes after BATLOW# is deasserted. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-31. Causes of Wake Events Cause RTC Alarm Power Button States Can Wake From S1–S5 (Note 1) S1–S5 How Enabled Set RTC_EN bit in PM1_EN register Always enabled as Wake event. (Note 2). GPE0_EN register GPI[0:15] S1–S5 (Note 1) Note: GPI’s that are in the core well are not capable of waking the system from sleep states when the core well is not powered. Classic USB S1–S4 Set USB1_EN, USB 2_EN, USB3_EN, USB4_EN, USB5_EN, and USB6_EN bits in GPE0_EN register LAN S1–S5 Will use PME#. Wake enable set with LAN logic. RI# S1–S5 (Note 1) Intel® High Definition Audio S1–S5 Set RI_EN bit in GPE0_EN register Event sets PME_B0_STS bit; PM_B0_EN must be enabled. Can not wake from S5 state if it was entered due to power failure or power button override. S1–S5 (Note 1) PME_B0_EN bit in GPE0_EN register Secondary PME# S1–S5 Set PME_EN bit in GPE0_EN register. PCI_EXP_WAKE# S1–S5 PCI_EXP_WAKE bit (Note 3) Primary PME# Must use the PCI Express* WAKE# pin rather than messages for wake from S3,S4, or S5. PCI_EXP PME Message S1 SMBALERT# S1–S5 Always enabled as Wake event SMBus Slave Wake Message (01h) S1–S5 Wake/SMI# command always enabled as a Wake event. Note: SMBus Slave Message can wake the system from S1– S5, as well as from S5 due to Power Button Override. (Note 2). SMBus Host Notify message received S1–S5 HOST_NOTIFY_WKEN bit SMBus Slave Command register. Reported in the SMB_WAK_STS bit in the GPEO_STS register. ME Non-Maskable Wake S1-S5 Always enabled as Wake event. (Note 2). NOTES: 1. This is a wake event from S5 only if the sleep state was entered by setting the SLP_EN and SLP_TYP bits via software, or if there is a power failure. 2. If in the S5 state due to a power button override or THRMTRIP#, the possible wake events are due to Power Button, Hard Reset Without Cycling (See Command Type 3 in Table 5-53), Hard Reset System (See Command Type 4 in Table 5-53), Wake SMBus Slave Message (01h) and ME initiated non-maskable wake. 3. When the WAKE# pin is active and the PCI Express device is enabled to wake the system, the ICH9 will wake the platform. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 171 Functional Description It is important to understand that the various GPIs have different levels of functionality when used as wake events. The GPIs that reside in the core power well can only generate wake events from sleep states where the core well is powered. Also, only certain GPIs are “ACPI Compliant,” meaning that their Status and Enable bits reside in ACPI I/O space. Table 5-32 summarizes the use of GPIs as wake events. Table 5-32. GPI Wake Events GPI Power Well Wake From Notes GPI[7:0] Core S1 ACPI Compliant GPI[15:8] Suspend S1–S5 ACPI Compliant The latency to exit the various Sleep states varies greatly and is heavily dependent on power supply design, so much so that the exit latencies due to the ICH9 are insignificant. 5.13.7.4 PCI Express* WAKE# Signal and PME Event Message PCI Express ports can wake the platform from any sleep state (S1, S3, S4, or S5) using the WAKE# pin. WAKE# is treated as a wake event, but does not cause any bits to go active in the GPE_STS register. PCI Express ports and the (G)MCH (via DMI) have the ability to cause PME using messages. When a PME message is received, ICH9 will set the PCI_EXP_STS bit. 5.13.7.5 Sx-G3-Sx, Handling Power Failures Depending on when the power failure occurs and how the system is designed, different transitions could occur due to a power failure. The AFTER_G3 bit provides the ability to program whether or not the system should boot once power returns after a power loss event. If the policy is to not boot, the system remains in an S5 state (unless previously in S4). There are only three possible events that will wake the system after a power failure. 1. PWRBTN#: PWRBTN# is always enabled as a wake event. When RSMRST# is low (G3 state), the PWRBTN_STS bit is reset. When the ICH9 exits G3 after power returns (RSMRST# goes high), the PWRBTN# signal is already high (because VCCstandby goes high before RSMRST# goes high) and the PWRBTN_STS bit is 0. 2. RI#: RI# does not have an internal pull-up. Therefore, if this signal is enabled as a wake event, it is important to keep this signal powered during the power loss event. If this signal goes low (active), when power returns the RI_STS bit is set and the system interprets that as a wake event. 3. RTC Alarm: The RTC_EN bit is in the RTC well and is preserved after a power loss. Like PWRBTN_STS the RTC_STS bit is cleared when RSMRST# goes low. The ICH9 monitors both PWROK and RSMRST# to detect for power failures. If PWROK goes low, the PWROK_FLR bit is set. If RSMRST# goes low, PWR_FLR is set. Note: 172 Although PME_EN is in the RTC well, this signal cannot wake the system after a power loss. PME_EN is cleared by RTCRST#, and PME_STS is cleared by RSMRST#. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-33. Transitions Due to Power Failure 5.13.8 State at Power Failure AFTERG3_EN bit Transition When Power Returns S0, S1, S3 1 0 S5 S0 S4 1 0 S4 S0 S5 1 0 S5 S0 Thermal Management The ICH9 has mechanisms to assist with managing thermal problems in the system. 5.13.8.1 THRM# Signal The THRM# signal is used as a status input for a thermal sensor. Based on the THRM# signal going active, the ICH9 generates an SMI# or SCI (depending on SCI_EN). If the THRM_POL bit is set low, when the THRM# signal goes low, the THRM_STS bit will be set. This is an indicator that the thermal threshold has been exceeded. If the THRM_EN bit is set, then when THRM_STS goes active, either an SMI# or SCI will be generated (depending on the SCI_EN bit being set). The power management software (BIOS or ACPI) can then take measures to start reducing the temperature. Examples include shutting off unwanted subsystems, or halting the processor. By setting the THRM_POL bit to high, another SMI# or SCI can optionally be generated when the THRM# signal goes back high. This allows the software (BIOS or ACPI) to turn off the cooling methods. Note: THRM# assertion does not cause a TCO event message in S3 or S4. The level of the signal is not reported in the heartbeat message. 5.13.8.2 Software Initiated Passive Cooling This mode is initiated by software setting the THTL_EN or FORCE_THTL bits. Software sets the THTL_DTY or THRM_DTY bits to select throttle ratio and THTL_EN or FORCE_THTL bit to enable the throttling. Throttling results in STPCLK# active for a minimum time of 12.5% and a maximum of 87.5%. The period is 1024 PCI clocks. Thus, the STPCLK# signal can be active for as little as 128 PCI clocks or as much as 896 PCI clocks. The actual slowdown (and cooling) of the processor depends on the instruction stream, because the processor is allowed to finish the current instruction. Furthermore, the ICH9 waits for the STOPGRANT cycle before starting the count of the time the STPCLK# signal is active. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 173 Functional Description 5.13.8.3 THRM# Override Software Bit The FORCE_THTL bit allows the BIOS to force passive cooling, independent of the ACPI software (which uses the THTL_EN and THTL_DTY bits). If this bit is set, the ICH9 starts throttling using the ratio in the THRM_DTY field. When this bit is cleared the ICH9 stops throttling, unless the THTL_EN bit is set (indicating that ACPI software is attempting throttling). If both the THTL_EN and FORCE_THTL bits are set, then the ICH should use the duty cycle defined by the THRM_DTY field, not the THTL_DTY field. 5.13.8.4 Active Cooling Active cooling involves fans. The GPIO signals from the ICH9 can be used to turn on/off a fan. 5.13.9 Event Input Signals and Their Usage The ICH9 has various input signals that trigger specific events. This section describes those signals and how they should be used. 5.13.9.1 PWRBTN# (Power Button) The ICH9 PWRBTN# signal operates as a “Fixed Power Button” as described in the Advanced Configuration and Power Interface, Version 2.0b. PWRBTN# signal has a 16 ms de-bounce on the input. The state transition descriptions are included in Table 5-34. Note that the transitions start as soon as the PWRBTN# is pressed (but after the debounce logic), and does not depend on when the Power Button is released. Note: During the time that the SLP_S4# signal is stretched for the minimum assertion width (if enabled), the Power Button is not a wake event. Refer to Power Button Override Function section below for further detail. Table 5-34. Transitions Due to Power Button Present State Transition/Action S0/Cx PWRBTN# goes low SMI# or SCI generated (depending on SCI_EN, PWRBTN_INIT_EN, PWRBTN_EN and GLB_SMI_EN) S1–S5 PWRBTN# goes low Wake Event. Transitions to S0 state G3 PWRBTN# pressed None S0–S4 174 Event PWRBTN# held low for at least 4 consecutive seconds Comment Software typically initiates a Sleep state Standard wakeup No effect since no power Not latched nor detected Unconditional transition to S5 state No dependence on processor (e.g., Stop-Grant cycles) or any other subsystem Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Power Button Override Function If PWRBTN# is observed active for at least four consecutive seconds, the state machine unconditionally transitions to the G2/S5 state, regardless of present state (S0–S4), even if PWROK is not active. In this case, the transition to the G2/S5 state does not depend on any particular response from the processor (e.g., a Stop-Grant cycle), nor any similar dependency from any other subsystem. The PWRBTN# status is readable to check if the button is currently being pressed or has been released. The status is taken after the de-bounce, and is readable via the PWRBTN_LVL bit. Note: The 4-second PWRBTN# assertion should only be used if a system lock-up has occurred. The 4-second timer starts counting when the ICH9 is in a S0 state. If the PWRBTN# signal is asserted and held active when the system is in a suspend state (S1–S5), the assertion causes a wake event. Once the system has resumed to the S0 state, the 4second timer starts. Note: During the time that the SLP_S4# signal is stretched for the minimum assertion width (if enabled by D31:F0:A4h bit 3), the Power Button is not a wake event. As a result, it is conceivable that the user will press and continue to hold the Power Button waiting for the system to awake. Since a 4-second press of the Power Button is already defined as an Unconditional Power down, the power button timer will be forced to inactive while the power-cycle timer is in progress. Once the power-cycle timer has expired, the Power Button awakes the system. Once the minimum SLP_S4# power cycle expires, the Power Button must be pressed for another 4 to 5 seconds to create the Override condition to S5. Sleep Button The Advanced Configuration and Power Interface, Version 2.0b defines an optional Sleep button. It differs from the power button in that it only is a request to go from S0 to S1–S4 (not S5). Also, in an S5 state, the Power Button can wake the system, but the Sleep Button cannot. Although the ICH9 does not include a specific signal designated as a Sleep Button, one of the GPIO signals can be used to create a “Control Method” Sleep Button. See the Advanced Configuration and Power Interface, Version 2.0b for implementation details. 5.13.9.2 RI# (Ring Indicator) The Ring Indicator can cause a wake event (if enabled) from the S1–S5 states. Table 5-35 shows when the wake event is generated or ignored in different states. If in the G0/S0/Cx states, the ICH9 generates an interrupt based on RI# active, and the interrupt will be set up as a Break event. Table 5-35. Transitions Due to RI# Signal Note: Present State Event RI_EN Event S0 RI# Active X Ignored S1–S5 RI# Active 0 Ignored 1 Wake Event Filtering/Debounce on RI# will not be done in ICH9. Can be in modem or external. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 175 Functional Description 5.13.9.3 PME# (PCI Power Management Event) The PME# signal comes from a PCI device to request that the system be restarted. The PME# signal can generate an SMI#, SCI, or optionally a Wake event. The event occurs when the PME# signal goes from high to low. No event is caused when it goes from low to high. There is also an internal PME_B0 bit. This is separate from the external PME# signal and can cause the same effect. 5.13.9.4 SYS_RESET# Signal When the SYS_RESET# pin is detected as active after the 16 ms debounce logic, the ICH9 attempts to perform a “graceful” reset, by waiting up to 25 ms for the SMBus to go idle. If the SMBus is idle when the pin is detected active, the reset occurs immediately; otherwise, the counter starts. If at any point during the count the SMBus goes idle the reset occurs. If, however, the counter expires and the SMBus is still active, a reset is forced upon the system even though activity is still occurring. Once the reset is asserted, it remains asserted for 5 to 6 ms regardless of whether the SYSRESET# input remains asserted or not. It cannot occur again until SYS_RESET# has been detected inactive after the debounce logic, and the system is back to a full S0 state with PLTRST# inactive. Note that if bit 3 of the CF9h I/O register is set then SYS_RESET# will result in a full power cycle reset. 5.13.9.5 THRMTRIP# Signal If THRMTRIP# goes active, the processor is indicating an overheat condition, and the ICH9 immediately transitions to an S5 state. However, since the processor has overheated, it does not respond to the ICH9’s STPCLK# pin with a stop grant special cycle. Therefore, the ICH9 does not wait for one. Immediately upon seeing THRMTRIP# low, the ICH9 initiates a transition to the S5 state, drive SLP_S3#, SLP_S4#, SLP_S5# low, and set the CTS bit. The transition looks like a power button override. When a THRMTRIP# event occurs, the ICH9 will power down immediately without following the normal S0 -> S5 path. The ICH9 will immediately drive SLP_S3#, SLP_S4#, and SLP_S5# low after sampling THRMTRIP# active. If the processor is running extremely hot and is heating up, it is possible (although very unlikely) that components around it, such as the ICH9, are no longer executing cycles properly. Therefore, if THRMTRIP# goes active, and the ICH9 is relying on state machine logic to perform the power down, the state machine may not be working, and the system will not power down. The ICH provides filtering for short low glitches on the THRMTRIP# signal in order to prevent erroneous system shut downs from noise. Glitches shorter than 25nsec are ignored. During boot, THRMTRIP# is ignored until SLP_S3#, PWROK, VRMPWRGD/VGATE, and PLTRST# are all ‘1’. During entry into a powered-down state (due to S3, S4, S5 entry, power cycle reset, etc.) THRMTRIP# is ignored until either SLP_S3# = 0, or PWROK = 0, or VRMPWRGD/VGATE = 0. Note: A thermal trip event will: • • • • 176 Set the AFTERG3_EN bit Clear the PWRBTN_STS bit Clear all the GPE0_EN register bits Clear the SMB_WAK_STS bit only if SMB_SAK_STS was set due to SMBus slave receiving message and not set due to SMBAlert Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.10 ALT Access Mode Before entering a low power state, several registers from powered down parts may need to be saved. In the majority of cases, this is not an issue, as registers have read and write paths. However, several of the ISA compatible registers are either read only or write only. To get data out of write-only registers, and to restore data into read-only registers, the ICH9 implements an ALT access mode. If the ALT access mode is entered and exited after reading the registers of the ICH9 timer (8254), the timer starts counting faster (13.5 ms). The following steps listed below can cause problems: 1. BIOS enters ALT access mode for reading the ICH9 timer related registers. 2. BIOS exits ALT access mode. 3. BIOS continues through the execution of other needed steps and passes control to the operating system. After getting control in step #3, if the operating system does not reprogram the system timer again, the timer ticks may be happening faster than expected. For example DOS and its associated software assume that the system timer is running at 54.6 ms and as a result the time-outs in the software may be happening faster than expected. Operating systems (e.g., Microsoft Windows* 98, Windows* 2000, and Windows NT*) reprogram the system timer and therefore do not encounter this problem. For some other loss (e.g., Microsoft MS-DOS*) the BIOS should restore the timer back to 54.6 ms before passing control to the operating system. If the BIOS is entering ALT access mode before entering the suspend state it is not necessary to restore the timer contents after the exit from ALT access mode. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 177 Functional Description 5.13.10.1 Write Only Registers with Read Paths in ALT Access Mode The registers described in Table 5-36 have read paths in ALT access mode. The access number field in the table indicates which register will be returned per access to that port. Table 5-36. Write Only Registers with Read Paths in ALT Access Mode (Sheet 1 of 2) Restore Data I/O Addr 00h 01h 02h 03h 04h 05h 06h 07h 178 # of Rds Access Restore Data Data I/O Addr # of Rds Access Data 1 DMA Chan 0 base address low byte 1 Timer Counter 0 status, bits [5:0] 2 DMA Chan 0 base address high byte 2 Timer Counter 0 base count low byte 1 DMA Chan 0 base count low byte 3 Timer Counter 0 base count high byte 2 DMA Chan 0 base count high byte 4 Timer Counter 1 base count low byte 1 DMA Chan 1 base address low byte 5 Timer Counter 1 base count high byte 2 DMA Chan 1 base address high byte 6 Timer Counter 2 base count low byte 1 DMA Chan 1 base count low byte 7 Timer Counter 2 base count high byte 2 DMA Chan 1 base count high byte 41h 1 Timer Counter 1 status, bits [5:0] 1 DMA Chan 2 base address low byte 42h 1 Timer Counter 2 status, bits [5:0] 2 DMA Chan 2 base address high byte 70h 1 Bit 7 = NMI Enable, Bits [6:0] = RTC Address 1 DMA Chan 2 base count low byte 2 DMA Chan 2 base count high byte 1 DMA Chan 3 base address low byte 2 DMA Chan 3 base address high byte 1 DMA Chan 3 base count low byte 2 DMA Chan 3 base count high byte 2 2 2 2 2 2 2 2 40h C4h C6h C8h 7 1 DMA Chan 5 base address low byte 2 DMA Chan 5 base address high byte 1 DMA Chan 5 base count low byte 2 DMA Chan 5 base count high byte 1 DMA Chan 6 base address low byte 2 DMA Chan 6 base address high byte 2 2 2 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-36. Write Only Registers with Read Paths in ALT Access Mode (Sheet 2 of 2) Restore Data I/O Addr # of Rds Access Restore Data Data I/O Addr 20h Data 1 DMA Chan 6 base count low byte DMA Chan 0–3 Command2 2 DMA Chan 0–3 Request 2 DMA Chan 6 base count high byte 3 DMA Chan 0 Mode: Bits(1:0) = 00 1 DMA Chan 7 base address low byte 4 DMA Chan 1 Mode: Bits(1:0) = 01 2 DMA Chan 7 base address high byte 5 DMA Chan 2 Mode: Bits(1:0) = 10 1 DMA Chan 7 base count low byte 6 DMA Chan 3 Mode: Bits(1:0) = 11. 2 DMA Chan 7 base count high byte 1 PIC ICW2 of Master controller 1 DMA Chan 4–7 Command2 2 PIC ICW3 of Master controller 2 DMA Chan 4–7 Request 3 PIC ICW4 of Master controller 3 DMA Chan 4 Mode: Bits(1:0) = 00 4 PIC OCW1 of Master controller1 4 DMA Chan 5 Mode: Bits(1:0) = 01 5 PIC OCW2 of Master controller 5 DMA Chan 6 Mode: Bits(1:0) = 10 6 PIC OCW3 of Master controller 6 DMA Chan 7 Mode: Bits(1:0) = 11. 7 PIC ICW2 of Slave controller 8 PIC ICW3 of Slave controller 9 PIC ICW4 of Slave controller 6 12 Access 1 CAh 08h # of Rds 10 PIC OCW1 of Slave controller1 11 PIC OCW2 of Slave controller 12 PIC OCW3 of Slave controller CCh CEh D0h 2 2 2 6 NOTES: 1. The OCW1 register must be read before entering ALT access mode. 2. Bits 5, 3, 1, and 0 return 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 179 Functional Description 5.13.10.2 PIC Reserved Bits Many bits within the PIC are reserved, and must have certain values written in order for the PIC to operate properly. Therefore, there is no need to return these values in ALT access mode. When reading PIC registers from 20h and A0h, the reserved bits shall return the values listed in Table 5-37. Table 5-37. PIC Reserved Bits Return Values 5.13.10.3 PIC Reserved Bits Value Returned ICW2(2:0) 000 ICW4(7:5) 000 ICW4(3:2) 00 ICW4(0) 0 OCW2(4:3) 00 OCW3(7) 0 OCW3(5) Reflects bit 6 OCW3(4:3) 01 Read Only Registers with Write Paths in ALT Access Mode The registers described in Table 5-38 have write paths to them in ALT access mode. Software restores these values after returning from a powered down state. These registers must be handled special by software. When in normal mode, writing to the base address/count register also writes to the current address/count register. Therefore, the base address/count must be written first, then the part is put into ALT access mode and the current address/count register is written. Table 5-38. Register Write Accesses in ALT Access Mode 180 I/O Address Register Write Value 08h DMA Status Register for channels 0–3. D0h DMA Status Register for channels 4–7. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.11 System Power Supplies, Planes, and Signals 5.13.11.1 Power Plane Control with SLP_S3#, SLP_S4#, SLP_S5# and SLP_M# The SLP_S3# output signal can be used to cut power to the system core supply, since it only goes active for the Suspend-to-RAM state (typically mapped to ACPI S3). Power must be maintained to the ICH9 suspend well, and to any other circuits that need to generate Wake signals from the Suspend-to-RAM state. During S3 (Suspend-to-RAM) all signals attached to powered down plans will be tri-stated or driven low, unless they are pulled via a pull-up resistor. Cutting power to the core may be done via the power supply, or by external FETs on the motherboard. The SLP_S4# or SLP_S5# output signal can be used to cut power to the system core supply, as well as power to the system memory, since the context of the system is saved on the disk. Cutting power to the memory may be done via the power supply, or by external FETs on the motherboard. The SLP_S4# output signal is used to remove power to additional subsystems that are powered during SLP_S3#. SLP_S5# output signal can be used to cut power to the system core supply, as well as power to the system memory, since the context of the system is saved on the disk. Cutting power to the memory may be done via the power supply, or by external FETs on the motherboard. SLP_M# output signal can be used to cut power to the Controller Link, Clock chip and SPI flash on a platform that supports Intel® AMT (Digital Office only) or ASF. 5.13.11.2 SLP_S4# and Suspend-To-RAM Sequencing The system memory suspend voltage regulator is controlled by the Glue logic. The SLP_S4# signal should be used to remove power to system memory rather than the SLP_S5# signal. The SLP_S4# logic in the ICH9 provides a mechanism to fully cycle the power to the DRAM and/or detect if the power is not cycled for a minimum time. Note: To utilize the minimum DRAM power-down feature that is enabled by the SLP_S4# Assertion Stretch Enable bit (D31:F0:A4h bit 3), the DRAM power must be controlled by the SLP_S4# signal. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 181 Functional Description 5.13.11.3 PWROK Signal The PWROK input should go active no sooner than 99 ms after the core supply voltages becoming valid. PWROK must not glitch, even if RSMRST# is low. Note: 1. SYSRESET# is recommended for implementing the system reset button. This saves external logic that is needed if the PWROK input is used. Additionally, it allows for better handling of the SMBus and processor resets, and avoids improperly reporting power failures. 2. PWROK and RSMRST# are sampled using the RTC clock. Therefore, low times that are less than one RTC clock period may not be detected by the ICH9. 3. In the case of true PWROK failure, PWROK will go low before VRMPWRGD. 4. When PWROK goes inactive, a host power cycle reset will occur. A host power cycle is the assertion of SLP_S3#, SLP_S4#, and SLP_S5#, and the deassertion of these signals 3-5 seconds later. The Management Engine remains powered throughout this cycle. 5.13.11.4 CPUPWRGD Signal This signal is connected to the processor’s VRM via the VRMPWRGD signal and is internally AND’d with the PWROK signal that comes from the system power supply. 5.13.11.5 VRMPWRGD Signal VRMPWRGD is an input from the regulator indicating that all of the outputs from the regulator are on and within specification. Platforms that use the VRMPWRGD signal to start the clock chip PLLs assume that it asserts milliseconds before PWROK in order to provide valid clocks in time for the PWROK rising. Note: When VRMPWRGD goes inactive, a host power cycle reset will occur. A host power cycle is the assertion of SLP_S3#, SLP_S4#, and SLP_S5#, and the deassertion of these signals 3-5 seconds later. The Management Engine remains powered throughout this cycle. 5.13.11.6 BATLOW# (Battery Low) (Mobile Only) The BATLOW# input can inhibit waking from S3, S4, and S5 states if there is not sufficient power. It also causes an SMI# if the system is already in an S0 state. 182 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.13.12 Clock Generators The clock generator is expected to provide the frequencies shown in Table 5-39. Table 5-39. Intel® ICH9 Clock Inputs Clock Domain Frequency Source Usage 100 MHz Main Clock Generator Used by SATA controller. Stopped in S3 – S based on SLP_S3# assertion. Main Clock Generator Used by DMI and PCI Express*. Stopped in S3 – S5 based on SLP_S3# assertion. 33 MHz Main Clock Generator Desktop: Free-running PCI Clock to ICH9. Stopped in S3 – S5 based on SLP_S3# assertion. Mobile: Free-running (not affected by STP_PCI# PCI Clock to ICH9. This is not the system PCI clock. This clock must keep running in S0 while the system PCI clock may stop based on CLKRUN# protocol. Stopped in S3 – S5 based on SLP_S3# assertion. CLK48 48.000 MHz Main Clock Generator Used by USB controllers and Intel® High Definition Audio controller. Stopped in S3 – S5 based on SLP_S3# assertion. CLK14 14.318 MHz Main Clock Generator Used by ACPI timers. Stopped in S3 – S5 based on SLP_S3# assertion. GLAN_CLK 5 to 62.5 MHz Platform LAN Connect LAN Connect Interface and Gigabit LAN Connect Interface. Control policy is determined by the clock source. SATA_CLK DMI_CLK PCICLK 5.13.12.1 Differential 100 MHz Differential Clock Control Signals from Intel® ICH9 to Clock Synthesizer (Mobile Only) The clock generator is assumed to have direct connect from the following ICH9 signals: • STP_CPU#: Stops processor clocks in C3 and C4 states • STP_PCI#: Stops system PCI clocks (not the ICH9 free-running 33 MHz clock) due to CLKRUN# protocol • SLP_S3#: Expected to drive clock chip PWRDOWN (through inverter), to stop clocks in S3 to S5. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 183 Functional Description 5.13.13 Legacy Power Management Theory of Operation Instead of relying on ACPI software, legacy power management uses BIOS and various hardware mechanisms. The scheme relies on the concept of detecting when individual subsystems are idle, detecting when the whole system is idle, and detecting when accesses are attempted to idle subsystems. However, the operating system is assumed to be at least APM enabled. Without APM calls, there is no quick way to know when the system is idle between keystrokes. The ICH9 does not support burst modes. 5.13.13.1 APM Power Management (Desktop Only) The ICH9 has a timer that, when enabled by the 1MIN_EN bit in the SMI Control and Enable register, generates an SMI# once per minute. The SMI handler can check for system activity by reading the DEVACT_STS register. If none of the system bits are set, the SMI handler can increment a software counter. When the counter reaches a sufficient number of consecutive minutes with no activity, the SMI handler can then put the system into a lower power state. If there is activity, various bits in the DEVACT_STS register will be set. Software clears the bits by writing a 1 to the bit position. The DEVACT_STS register allows for monitoring various internal devices, or Super I/O devices (SP, PP, FDC) on LPC or PCI, keyboard controller accesses, or audio functions on LPC or PCI. Other PCI activity can be monitored by checking the PCI interrupts. 5.13.13.2 Mobile APM Power Management (Mobile Only) In mobile systems, there are additional requirements associated with device power management. To handle this, the ICH9 has specific SMI# traps available. The following algorithm is used: 1. The periodic SMI# timer checks if a device is idle for the require time. If so, it puts the device into a low-power state and sets the associated SMI# trap. 2. When software (not the SMI# handler) attempts to access the device, a trap occurs (the cycle does not really go to the device and an SMI# is generated). 3. The SMI# handler turns on the device and turns off the trap. The SMI# handler exits with an I/O restart. This allows the original software to continue. 5.13.14 Reset Behavior When a reset is triggered, the ICH will send a warning message to the MCH to allow the MCH to attempt to complete any outstanding memory cycles and put memory into a safe state before the platform is reset. When the MCH is ready, it will send an acknowledge message to the ICH. Once the message is received the ICH asserts PLTRST#. The ICH does not require an acknowledge message from the MCH to trigger PLTRST#. A global reset will occur after 4 seconds if an acknowledge from the MCH is not received. Note: 184 When the ICH causes a reset by asserting PLTRST# its output signals will go to their reset states as defined in Chapter 3. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description A reset in which the host platform is reset and PLTRST# is asserted is called a Host Reset or Host Partition Reset. Depending on the trigger a host reset may also result in power cycling see Table 5-40 for details. If a host reset is triggered and the ICH times out before receiving an acknowledge message from the MCH a Global Reset with power cycle will occur. A reset in which the host and ME partitions of the platform are reset is called a Global Reset. The following table shows the various reset triggers: Table 5-40. Causes of Host and Global Resets Host Reset without Power Cycle Host Reset with Power Cycle Global Reset with Power Cycle Write of 0Eh to CF9h Register when Global Reset bit = 0b No Yes No (Note 1) Write of 06h to CF9h Register when Global Reset bit = 0b Yes No No (Note 1) Write of 06h or 0Eh to CF9h register when Global Reset bit = 1b No No Yes SYS_RESET# Asserted and CF9h bit 3 = 0 Yes No No (Note 1) SYS_RESET# Asserted and CF9h bit 3 = 1 No Yes No (Note 1) SMBus Slave Message received for Reset with Power Cycle No Yes No (Note 1) SMBus Slave Message received for Reset without Power Cycle Yes No No (Note 1) TCO Watchdog timer reaches zero two times Yes No No (Note 1) Power Failure: PWROK signal or VRMPWROK signal goes inactive or RSMRST# asserts No No Yes (Note 2) Special shutdown cycle from CPU causes CF9h-like PLTRST# and CF9h Global Reset bit = 1 No No Yes Special shutdown cycle from CPU causes CF9h-like PLTRST# and CF9h bit 3 = 1 No Yes No (Note 2) Special Shutdown Cycle from CPU causes CF9hlike PLTRST# and CF9h Global Reset bit = 0 Yes No No (Note 1) ME Triggered Host Reset without power cycle Yes No No (Note 1) ME Triggered Host Reset with power cycle No Yes No (Note 1) ME Triggered Global Reset No No Yes ME Initiated Host Reset with power down No Yes (Note 3) No (Note 1) Trigger NOTES: 1. Trigger will result in Global Reset with power cycle if the acknowledge message is not received by the ICH. 2. ICH does not send warning message to MCH, reset occurs without delay. 3. ICH waits for enabled wake event to complete reset. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 185 Functional Description 5.14 System Management (D31:F0) The ICH9 provides various functions to make a system easier to manage and to lower the Total Cost of Ownership (TCO) of the system. In addition, ICH9 provides integrated ASF Management support, requires use of SPI Flash and Management Engine firmware. Features and functions can be augmented via external A/D converters and GPIO, as well as an external microcontroller. The following features and functions are supported by the ICH9: • Processor present detection — Detects if processor fails to fetch the first instruction after reset • Various Error detection (such as ECC Errors) indicated by host controller — Can generate SMI#, SCI, SERR, NMI, or TCO interrupt • Intruder Detect input — Can generate TCO interrupt or SMI# when the system cover is removed — INTRUDER# allowed to go active in any power state, including G3 • Detection of bad BIOS Flash (FWH or Flash on SPI) programming — Detects if data on first read is FFh (indicates that BIOS flash is not programmed) • Ability to hide a PCI device — Allows software to hide a PCI device in terms of configuration space through the use of a device hide register (See Section 10.1.75) Note: Voltage ID from the processor can be read via GPI signals. ASF functionality with the integrated ICH9 ASF controller requires a correctly configured system, including an appropriate component of the ICH9 (see Section 1.3), (G)MCH with Management Engine, Management Engine Firmware, system BIOS support, and appropriate Platform LAN Connect Device. 5.14.1 Theory of Operation The System Management functions are designed to allow the system to diagnose failing subsystems. The intent of this logic is that some of the system management functionality can be provided without the aid of an external microcontroller. 5.14.1.1 Detecting a System Lockup When the processor is reset, it is expected to fetch its first instruction. If the processor fails to fetch the first instruction after reset, the TCO timer times out twice and the ICH9 asserts PLTRST#. 5.14.1.2 Handling an Intruder The ICH9 has an input signal, INTRUDER#, that can be attached to a switch that is activated by the system’s case being open. This input has a two RTC clock debounce. If INTRUDER# goes active (after the debouncer), this will set the INTRD_DET bit in the TCO_STS register. The INTRD_SEL bits in the TCO_CNT register can enable the ICH9 to cause an SMI# or interrupt. The BIOS or interrupt handler can then cause a transition to the S5 state by writing to the SLP_EN bit. The software can also directly read the status of the INTRUDER# signal (high or low) by clearing and then reading the INTRD_DET bit. This allows the signal to be used as a GPI if the intruder function is not required. 186 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description If the INTRUDER# signal goes inactive some point after the INTRD_DET bit is written as a 1, then the INTRD_DET signal will go to a 0 when INTRUDER# input signal goes inactive. Note that this is slightly different than a classic sticky bit, since most sticky bits would remain active indefinitely when the signal goes active and would immediately go inactive when a 1 is written to the bit. Note: The INTRD_DET bit resides in the ICH9’s RTC well, and is set and cleared synchronously with the RTC clock. Thus, when software attempts to clear INTRD_DET (by writing a 1 to the bit location) there may be as much as two RTC clocks (about 65 µs) delay before the bit is actually cleared. Also, the INTRUDER# signal should be asserted for a minimum of 1 ms to ensure that the INTRD_DET bit will be set. Note: If the INTRUDER# signal is still active when software attempts to clear the INTRD_DET bit, the bit remains set and the SMI is generated again immediately. The SMI handler can clear the INTRD_SEL bits to avoid further SMIs. However, if the INTRUDER# signal goes inactive and then active again, there will not be further SMIs, since the INTRD_SEL bits would select that no SMI# be generated. 5.14.1.3 Detecting Improper Firmware Hub Programming The ICH9 can detect the case where the BIOS flash is not programmed. This results in the first instruction fetched to have a value of FFh. If this occurs, the ICH9 sets the BAD_BIOS bit. The BIOS flash may reside in FWH or flash on the SPI bus. 5.14.1.4 Heartbeat and Event Reporting via SMLink/SMBus Heartbeat and event reporting via SMLink/SMBus is no longer supported. The AMT logic in ICH9 (Digital Office Only) can be programmed to generate an interrupt to the Management Engine when an event occurs. The Management Engine will poll the TCO registers to gather appropriate bits to send the event message to the Gigabit Ethernet controller, if Management Engine is programmed to do so. The Management Engine is responsible for sending ASF 2.0 messages if programmed to do so. In Advanced TCO BMC mode, the external micro-controller (BMC) accesses the TCO info through SMBus. 5.14.2 TCO Modes 5.14.2.1 TCO Legacy/Compatible Mode In TCO Legacy/Compatible mode the Intel Management Engine and Intel AMT logic (Digital Office only) and AMT SMBus controllers are disabled. To enable Legacy/ Compatible TCO mode the TCOMODE bit 7 in the ICHSTRP0 register in the SPI device must be 0. Note: SMBus and SMLink may be tied together externally, if a device has a single SMBus interface and needs access to the TCO slave and be visisble to the host SMBus controller. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 187 Functional Description . Figure 5-6. TCO Legacy/Compatible Mode SMBus Configuration Intel® ICH9 TCO Compatible Mode ® Intel AMT SMBus Controller 2 X Intel® AMT SMBus Controller 1 X SPD (Slave) uCtrl SMBus Host SMBus Legacy Sensors (Master or Slave with ALERT) TCO Slave SMLink ASF Sensors (Master or Slave) In TCO Legacy/Compatible mode the Intel ICH9 can function directly with the integrated Gigabit Ethernet controller or equivalent external LAN controller to report messages to a network management console without the aid of the system processor. This is crucial in cases where the processor is malfunctioning or cannot function due to being in a low-power state. Table 5-41 includes a list of events that will report messages to the network management console. Table 5-41. Event Transitions that Cause Messages Event INTRUDER# pin Assertion? Deassertion? Comments yes no Must be in “S1 or hung S0” state Must be in “S1 or hung S0” state. Note that the THRM# pin is isolated when the core power is off, thus preventing this event in S3-S5. THRM# pin yes yes Watchdog Timer Expired yes no (NA) GPIO[11]/ SMBALERT# pin yes yes Must be in “S1 or hung S0” state BATLOW# (Mobile Only) yes yes Must be in “S1 or hung S0” state CPU_PWR_FLR yes no “S1 or hung S0” state entered “S1 or hung S0” state entered NOTE: The GPIO11/SMBALERT# pin will trigger an event message (when enabled by the GPIO11_ALERT_DISABLE bit) regardless of whether it is configured as a GPI or not. 188 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.14.2.2 Advanced TCO Mode Intel ICH9 supports two modes of Advanced TCO. Intel® Active Management Technology mode (Digital Office only) and BMC mode. To enable Advance TCO mode (AMT or BMC mode) the TCOMODE bit 7 in the ICHSTRP0 register in the SPI device must be 1. 5.14.2.2.1 Advanced TCO Intel® Active Management Technology mode (Digital Office Only) In this mode, AMT SMBus Controller 1, Host SMBus and SMLink are connected together internally. See Figure 5-7. This mode is enabled when the BMCMODE bit 15 in the ICHSTRP0 register in the SPI device is 0. The AMT SMBus Controller 2 can be connected to either the SMBus pins or the SMLink pins by the MESM2SEL bit 23 in the ICHSTRP0 register in the SPI device. The default is to have the AMT SMBus Controller 2 connected to SMLink. The AMT SMBus Controller 2 has no connection to LINKALERT#. Figure 5-7. Advanced TCO Intel® AMT Mode SMBus/SMLink Configuration Intel® ICH9 Intel® AMT AMT SMBus SMBus Controller 2 Controller 2 Advanced TCO AMT Mode SMLink Intel® AMT AMT SMBus SMBus Controller 1 Controller 1 Embedded Controller SPD (Slave) uCtrl Host SMBus SMBus TCO Slave 5.14.2.2.2 Legacy Sensors (Master or Slave with ALERT) ASF Sensors (Master or Slave) Advanced TCO BMC Mode In this mode, the external microcontroller (BMC) is connected to both SMLink and SMBus. The BMC communicates with Management Engine through AMT SMBus connected to SMLink. The host and TCO slave communicated with BMC through SMBus. See Figure 5-8. This mode is enabled when the BMCMODE bit 15 in the ICHSTRP0 register in the SPI device is 1. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 189 Functional Description Figure 5-8. Advanced TCO BMC Mode SMBus/SMLink Configuration Advanced TCO BMC Mode Intel® ICH9 Intel® AMT SMBus Controller 2 Intel® AMT SMBus Controller 1 SMLink BMC SPD (Slave) Host SMBus SMBus TCO Slave 5.15 Legacy Sensors (Master or Slave with ALERT) ASF Sensors (Master or Slave) General Purpose I/O (D31:F0) The ICH9 contains up to 61 General Purpose Input/Output (GPIO) signals. Each GPIO can be configured as an input or output signal. The number of inputs and outputs varies depending on ICH9 configuration. 5.15.1 Power Wells Some GPIOs exist in the suspend power plane. Care must be taken to make sure GPIO signals are not driven high into powered-down planes. Some ICH9 GPIOs may be connected to pins on devices that exist in the core well. If these GPIOs are outputs, there is a danger that a loss of core power (PWROK low) or a Power Button Override event results in the ICH9 driving a pin to a logic 1 to another device that is powered down. 5.15.2 SMI# and SCI Routing The routing bits for GPIO[0:15] allow an input to be routed to SMI# or SCI, or neither. Note that a bit can be routed to either an SMI# or an SCI, but not both. 190 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.15.3 Triggering GPIO[1:15] have “sticky” bits on the input. Refer to the GPE0_STS register. As long as the signal goes active for at least 2 clock cycles, the ICH9 keeps the sticky status bit active. The active level can be selected in the GP_LVL register. If the system is in an S0 or an S1 state, the GPI inputs are sampled at 33 MHz, so the signal only needs to be active for about 60 ns to be latched. In the S3–S5 states, the GPI inputs are sampled at 32.768 kHz, and thus must be active for at least 61 microseconds to be latched. If the input signal is still active when the latch is cleared, it will again be set. Another edge trigger is not required. This makes these signals “level” triggered inputs. 5.15.4 Serial POST Codes Over GPIO ICH9 adds the extended capability allowing system software to serialize POST or other messages on GPIO. This capability negates the requirement for dedicated diagnostic LEDs on the platform. Additionally, based on the newer BTX form factors, the PCI bus as a target for POST codes is increasingly difficult to support as the total number of PCI devices supported are decreasing. 5.15.4.1 Theory of operation For the ICH9 generation POST code serialization logic will be shared with GPIO. These GPIOs will likely be shared with LED control offered by the Super I/O (SIO) component. The following reference diagram shows a likely configuration. Figure 5-9. Serial Post over GPIO Reference Circuit V_3P3_STBY R ICH SIO LED Note: The pull-up value is based on the brightness required. The anticipated usage model is that either the ICH9 or the SIO can drive a pin low to turn off an LED. In the case of the power LED, the SIO would normally leave its corresponding pin in a high-Z state to allow the LED to turn on. In this state, the ICH9 can blink the LED by driving its corresponding pin low and subsequently tri-stating the buffer. An external optical sensing device can detect the on/off state of the LED. By externally post-processing the information from the optical device, the serial bit stream can be recovered. The hardware will supply a ‘sync’ byte before the actual data transmission to allow external detection of the transmit frequency. The frequency of transmission should be limited to 1 transition every 1μs to ensure the detector can reliably sample Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 191 Functional Description the on/off state of the LED. To allow flexibility in pull-up resistor values for power optimization, the frequency of the transmission is programmable via the DRS field in the GP_SB_CMDSTS register (Section 13.10.6). The serial bit stream is Manchester encoded. This choice of transmission ensures that a transition will be seen on every clock. The 1 or 0 data is based on the transmission happening during the high or low phase of the clock. A simplified hardware/software register interface provides control and status information to track the activity of this block. Software enabling the serial blink capability should implement an algorithm referenced below to send the serialized message on the enabled GPIO. 1. Read the Go/Busy status bit in the GP_SB_CMDSTS register and verify it is cleared. This will ensure that the GPIO is idled and a previously requested message is still not in progress. 2. Write the data to serialize into the GP_SB_DATA register (Section 13.10.7). 3. Write the DLS and DRS values into the GP_SB_CMDSTS register and set the Go bit. This may be accomplished using a single write. The reference diagram shows the LEDs being powered from the suspend supply. By providing a generic capability that can be used both in the main and the suspend power planes maximum flexibility can be achieved. A key point to make is that the ICH will not unintentionally drive the LED control pin low unless a serialization is in progress. System board connections utilizing this serialization capability are required to use the same power plane controlling the LED as the ICH9 GPIO pin. Otherwise, the ICH9 GPIO may float low during the message and prevent the LED from being controlled from the SIO. The hardware will only be serializing messages when the core power well is powered and the processor is operational. Care should be taken to prevent the ICH9 from driving an active ‘1’ on a pin sharing the serial LED capability. Since the SIO could be driving the line to 0, having the ICH drive a 1 would create a high current path. A recommendation to avoid this condition involves choosing a GPIO defaulting to an input. The GP_SER_BLINK register (Section 13.10.7) should be set first before changing the direction of the pin to an output. This sequence ensures the open-drain capability of the buffer is properly configured before enabling the pin as an output. 5.15.4.2 Serial Message Format In order to serialize the data onto the GPIO, an initial state of high-Z is assumed. The SIO is required to have its LED control pin in a high-Z state as well to allow ICH9 to blink the LED (refer to the reference diagram). The three components of the serial message include the sync, data, and idle fields. The sync field is 7 bits of ‘1’ data followed by 1 bit of ‘0’ data. Starting from the high-Z state (LED on) provides external hardware a known initial condition and a known pattern. In case one or more of the leading 1 sync bits are lost, the 1s followed by 0 provide a clear indication of ‘end of sync’. This pattern will be used to ‘lock’ external sampling logic to the encoded clock. The data field is shifted out with the highest byte first (MSB). Within each byte, the most significant bit is shifted first (MSb). The idle field is enforced by the hardware and is at least 2 bit times long. The hardware will not clear the Busy and Go bits until this idle time is met. Supporting the idle time in hardware prevents time-based counting in BIOS as the hardware is immediately ready for the next serial code when the Go bit is cleared. Note that the idle state is represented as a high-Z condition on the pin. If the last transmitted bit is a 1, returning 192 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description to the idle state will result in a final 0-1 transition on the output Manchester data. Two full bit times of idle correspond to a count of 4 time intervals (the width of the time interval is controlled by the DRS field). The following waveform shows a 1-byte serial write with a data byte of 5Ah. The internal clock and bit position are for reference purposes only. The Manchester D is the resultant data generated and serialized onto the GPIO. Since the buffer is operating in open-drain mode the transitions are from high-Z to 0 and back. Bit 7 6 5 4 3 2 1 0 Internal Clock Manchester D 8-bit sync field (1111_1110) 5.15.5 5A data byte 2 clk idle Controller Link GPIOs (Digital Office Only) The following GPIOs can be used as Controller Link GPIOs: GPIO9/WOL_EN, GPIO10/ CLGPIO1 (Desktop)/SUS_PWR_ACK (Mobile), GPIO14/CLGPIO2 (Desktop)/ AC_PRESENT (Mobile), GPIO24/MEM_LED, GPIO60/CLGPIO4, GPIO57/CLGPIO5 and GPIO58/CLGPIO6. Controller Link GPIOs are only available on Intel® AMT or ASF enabled platforms with supporting Management Engine Firmware. Controller Link GPIOs are owned by the management engine and are configured by Management Engine firmware. When configured a a Controller Link GPIO the GPIO_USE_SEL bit is ignored. If the Controller Link GPIO is utilized in a platform, its associated GPIO functionality is no longer available to the host. If the Controller Link GPIO is not utilized in a platform, the signal can instead be used as its associated General Purpose I/O. 5.16 SATA Host Controller (D31:F2, F5) The SATA function in the ICH9 has three modes of operation to support different operating system conditions. In the case of Native IDE enabled operating systems, the ICH9 utilizes two controllers to enable all six ports of the bus. The first controller (Device 31: Function 2) supports ports 0 -3 and the second controller (Device 31: Function 5) supports ports 4 and 5. When using a legacy operating system, only one controller (Device 31: Function 2) is available that supports ports 0 - 3. In AHCI or RAID mode, only one controller (Device 31: Function 2) is utilized enabling all six ports. The MAP register, Section 15.1.29, provides the ability to share PCI functions. When sharing is enabled, all decode of I/O is done through the SATA registers. Device 31, Function 1 (IDE controller) is hidden by software writing to the Function Disable Register (D31, F0, offset F2h, bit 1), and its configuration registers are not used. The ICH9 SATA controllers feature six (desktop only) / four (mobile only) sets of interface signals (ports) that can be independently enabled or disabled (they cannot be tri-stated or driven low). Each interface is supported by an independent DMA controller. The ICH9 SATA controllers interact with an attached mass storage device through a register interface that is equivalent to that presented by a traditional IDE host adapter. The host software follows existing standards and conventions when accessing the register interface and follows standard command protocol conventions. Note: SATA interface transfer rates are independent of UDMA mode settings. SATA interface transfer rates will operate at the bus’s maximum speed, regardless of the UDMA mode reported by the SATA device or the system BIOS. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 193 Functional Description 5.16.1 SATA Feature Support ICH9 (AHCI/RAID Disabled) ICH9 (AHCI/RAID Enabled) Native Command Queuing (NCQ) N/A Supported Auto Activate for DMA N/A Supported Hot Plug Support N/A Supported Asynchronous Signal Recovery N/A Supported Feature 3 Gb/s Transfer Rate Supported Supported ATAPI Asynchronous Notification N/A Supported Host & Link Initiated Power Management N/A Supported Supported Supported Command Completion Coalescing N/A N/A External SATA N/A Supported Staggered Spin-Up Feature 194 Description Native Command Queuing (NCQ) Allows the device to reorder commands for more efficient data transfers Auto Activate for DMA Collapses a DMA Setup then DMA Activate sequence into a DMA Setup only Hot Plug Support Allows for device detection without power being applied and ability to connect and disconnect devices without prior notification to the system Asynchronous Signal Recovery Provides a recovery from a loss of signal or establishing communication after hot plug 3 Gb/s Transfer Rate Capable of data transfers up to 3Gb/s ATAPI Asynchronous Notification A mechanism for a device to send a notification to the host that the device requires attention Host & Link Initiated Power Management Capability for the host controller or device to request Partial and Slumber interface power states Staggered Spin-Up Enables the host the ability to spin up hard drives sequentially to prevent power load problems on boot Command Completion Coalescing Reduces interrupt and completion overhead by allowing a specified number of commands to complete and then generating an interrupt to process the commands External SATA Technology that allows for an outside the box connection of up to 2 meters (when using the cable defined in SATA-IO) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.16.2 Theory of Operation 5.16.2.1 Standard ATA Emulation The ICH9 contains a set of registers that shadow the contents of the legacy IDE registers. The behavior of the Command and Control Block registers, PIO, and DMA data transfers, resets, and interrupts are all emulated. Note: The ICH9 will assert INTR when the master device completes the EDD command regardless of the command completion status of the slave device. If the master completes EDD first, an INTR is generated and BSY will remain '1' until the slave completes the command. If the slave completes EDD first, BSY will be '0' when the master completes the EDD command and asserts INTR. Software must wait for busy to clear (0) before completing an EDD command, as required by the ATA5 through ATA7 (T13) industry standards. 5.16.2.2 48-Bit LBA Operation The SATA host controller supports 48-bit LBA through the host-to-device register FIS when accesses are performed via writes to the task file. The SATA host controller will ensure that the correct data is put into the correct byte of the host-to-device FIS. There are special considerations when reading from the task file to support 48-bit LBA operation. Software may need to read all 16-bits. Since the registers are only 8-bits wide and act as a FIFO, a bit must be set in the device/control register, which is at offset 3F6h for primary and 376h for secondary (or their native counterparts). If software clears bit 7 of the control register before performing a read, the last item written will be returned from the FIFO. If software sets bit 7 of the control register before performing a read, the first item written will be returned from the FIFO. 5.16.3 SATA Swap Bay Support The ICH9 provides for basic SATA swap bay support using the PSC register configuration bits and power management flows. A device can be powered down by software and the port can then be disabled, allowing removal and insertion of a new device. Note: This SATA swap bay operation requires board hardware (implementation specific), BIOS, and operating system support. 5.16.4 Hot Plug Operation ICH9 supports Hot Plug Surprise removal and Insertion Notification in the PARTIAL, SLUMBER and Listen Mode states when used with Low Power Device Presence Detection. Software can take advantage of power savings in the low power states while enabling hot plug operation. Refer to chapter 7 of the AHCI specification for details. 5.16.4.1 Low Power Device Presence Detection Low Power Device Presence Detection enables SATA Link Power Management to coexist with hot plug (insertion and removal) without interlock switch or cold presence detect. The detection mechanism allows Hot Plug events to be detectable by hardware across all link power states (Active, PARTIAL, SLUMBER) as well as AHCI Listen Mode. If the Low Power Device Presence Detection circuit is disabled the ICH9 reverts to Hot Plug Surprise Removal Notification (without an interlock switch) mode that is mutually exclusive of the PARTIAL and SLUMBER power management states. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 195 Functional Description 5.16.5 Function Level Reset Support (FLR) The SATA Host Controller supports the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel® Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a PCI reset was asserted. 5.16.5.1 FLR Steps 5.16.5.1.1 FLR Initialization 1. A FLR is initiated by software writing a ‘1’ to the Initiate FLR bit. 2. All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.16.5.1.2 FLR Operation The Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 5.16.5.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: 196 From the time Initiate FLR bit is written to '1' software must wait at least 100 ms before accessing the function. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.16.6 Intel® Matrix Storage Technology Configuration (Intel® ICH9R, ICH9DH, ICH9DO, ICH9M and ICH9M-E Only) The Intel® Matrix Storage Technology offers several diverse options for RAID (redundant array of independent disks) to meet the needs of the end user. AHCI support provides higher performance and alleviates disk bottlenecks by taking advantage of the independent DMA engines that each SATA port offers in ICH9. • RAID Level 0 performance scaling up to 4 drives, enabling higher throughput for data intensive applications such as video editing. • Data security is offered through RAID Level 1, which performs mirroring. • RAID Level 10 provides high levels of storage performance with data protection, combining the fault-tolerance of RAID Level 1 with the performance of RAID Level 0. By striping RAID Level 1 segments, high I/O rates can be achieved on systems that require both performance and fault-tolerance. RAID Level 10 requires 4 hard drives, and provides the capacity of two drives. • RAID Level 5 provides highly efficient storage while maintaining fault-tolerance on 3 or more drives. By striping parity, and rotating it across all disks, fault tolerance of any single drive is achieved while only consuming 1 drive worth of capacity. That is, a 3 drive RAID 5 has the capacity of 2 drives, or a 4 drive RAID 5 has the capacity of 3 drives. RAID 5 has high read transaction rates, with a medium write rate. RAID 5 is well suited for applications that require high amounts of storage while maintaining fault tolerance. Note: Intel® Matrix Storage Technology RAID functionality not supported on ICH9M base component. By using the ICH9’s built-in Intel Matrix Storage Technology, there is no loss of PCI resources (request/grant pair) or add-in card slot. Intel® Matrix Storage Technology functionality requires the following items: 1. ICH9 component enabled for Intel Matrix Storage Technology (see Section 1.3) 2. Intel Matrix Storage Manager RAID Option ROM must be on the platform 3. Intel Matrix Storage Manager drivers, most recent revision. 4. At least two SATA hard disk drives (minimum depends on RAID configuration). Intel Matrix Storage Technology is not available in the following configurations: 1. The SATA controller is in compatible mode. 5.16.6.1 Intel® Matrix Storage Manager RAID Option ROM The Intel Matrix Storage Manager RAID Option ROM is a standard PnP Option ROM that is easily integrated into any System BIOS. When in place, it provides the following three primary functions: • Provides a text mode user interface that allows the user to manage the RAID configuration on the system in a pre-operating system environment. Its feature set is kept simple to keep size to a minimum, but allows the user to create & delete RAID volumes and select recovery options when problems occur. • Provides boot support when using a RAID volume as a boot disk. It does this by providing Int13 services when a RAID volume needs to be accessed by DOS applications (such as NTLDR) and by exporting the RAID volumes to the System BIOS for selection in the boot order. • At each boot up, provides the user with a status of the RAID volumes and the option to enter the user interface by pressing CTRL-I. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 197 Functional Description 5.16.7 Power Management Operation Power management of the ICH9 SATA controller and ports will cover operations of the host controller and the SATA wire. 5.16.7.1 Power State Mappings The D0 PCI power management state for device is supported by the ICH9 SATA controller. SATA devices may also have multiple power states. From parallel ATA, three device states are supported through ACPI. They are: • D0 – Device is working and instantly available. • D1 – device enters when it receives a STANDBY IMMEDIATE command. Exit latency from this state is in seconds • D3 – from the SATA device’s perspective, no different than a D1 state, in that it is entered via the STANDBY IMMEDIATE command. However, an ACPI method is also called which will reset the device and then cut its power. Each of these device states are subsets of the host controller’s D0 state. Finally, SATA defines three PHY layer power states, which have no equivalent mappings to parallel ATA. They are: • PHY READY – PHY logic and PLL are both on and active • Partial – PHY logic is powered, but in a reduced state. Exit latency is no longer than 10 ns • Slumber – PHY logic is powered, but in a reduced state. Exit latency can be up to 10 ms. Since these states have much lower exit latency than the ACPI D1 and D3 states, the SATA controller defines these states as sub-states of the device D0 state. Figure 5-10. SATA Power States Power Intel® ICH SATA Controller = D0 Device = D0 PHY = Ready PHY = Partial PHY = Slumber Device = D1 PHY = Off (port disabled) PHY = Slumber PHY = Off (port disabled) Device = D3 PHY = Slumber PHY = Off (port disabled) Resume Latency 198 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.16.7.2 Power State Transitions 5.16.7.2.1 Partial and Slumber State Entry/Exit The partial and slumber states save interface power when the interface is idle. It would be most analogous to PCI CLKRUN# (in power savings, not in mechanism), where the interface can have power saved while no commands are pending. The SATA controller defines PHY layer power management (as performed via primitives) as a driver operation from the host side, and a device proprietary mechanism on the device side. The SATA controller accepts device transition types, but does not issue any transitions as a host. All received requests from a SATA device will be ACKed. When an operation is performed to the SATA controller such that it needs to use the SATA cable, the controller must check whether the link is in the Partial or Slumber states, and if so, must issue a COM_WAKE to bring the link back online. Similarly, the SATA device must perform the same action. 5.16.7.2.2 Device D1, D3 States These states are entered after some period of time when software has determined that no commands will be sent to this device for some time. The mechanism for putting a device in these states does not involve any work on the host controller, other then sending commands over the interface to the device. The command most likely to be used in ATA/ATAPI is the “STANDBY IMMEDIATE” command. 5.16.7.2.3 Host Controller D3HOT State After the interface and device have been put into a low power state, the SATA host controller may be put into a low power state. This is performed via the PCI power management registers in configuration space. There are two very important aspects to note when using PCI power management. 1. When the power state is D3, only accesses to configuration space are allowed. Any attempt to access the memory or I/O spaces will result in master abort. 2. When the power state is D3, no interrupts may be generated, even if they are enabled. If an interrupt status bit is pending when the controller transitions to D0, an interrupt may be generated. When the controller is put into D3, it is assumed that software has properly shut down the device and disabled the ports. Therefore, there is no need to sustain any values on the port wires. The interface will be treated as if no device is present on the cable, and power will be minimized. When returning from a D3 state, an internal reset will not be performed. 5.16.7.2.4 Non-AHCI Mode PME# Generation When in non-AHCI mode (legacy mode) of operation, the SATA controller does not generate PME#. This includes attach events (since the port must be disabled), or interlock switch events (via the SATAGP pins). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 199 Functional Description 5.16.7.3 SMI Trapping (APM) Device 31:Function2:Offset C0h (see Section 14.1.37) contain control for generating SMI# on accesses to the IDE I/O spaces. These bits map to the legacy ranges (1F0– 1F7h, 3F6h, 170–177h, and 376h) and native IDE ranges defined by PCMDBA, PCTLBA, SCMDBA an SCTLBA. If the SATA controller is in legacy mode and is using these addresses, accesses to one of these ranges with the appropriate bit set causes the cycle to not be forwarded to the SATA controller, and for an SMI# to be generated. If an access to the Bus-Master IDE registers occurs while trapping is enabled for the device being accessed, then the register is updated, an SMI# is generated, and the device activity status bits (Section 14.1.38) are updated indicating that a trap occurred. 5.16.8 SATA Device Presence In legacy mode, the SATA controller does not generate interrupts based on hot plug/ unplug events. However, the SATA PHY does know when a device is connected (if not in a partial or slumber state), and it s beneficial to communicate this information to host software as this will greatly reduce boot times and resume times. The flow used to indicate SATA device presence is shown in Figure 5-11. The ‘PxE’ bit refers to PCS.P[3:0]E bits, depending on the port being checked and the ‘PxP’ bits refer to the PCS.P[3:0]P bits, depending on the port being checked. If the PCS/PxP bit is set a device is present, if the bit is cleared a device is not present. If a port is disabled, software can check to see if a new device is connected by periodically reenabling the port and observing if a device is present, if a device is not present it can disable the port and check again later. If a port remains enabled, software can periodically poll PCS.PxP to see if a new device is connected. Figure 5-11. Flow for Port Enable / Device Present Bits 5.16.9 SATA LED The SATALED# output is driven whenever the BSY bit is set in any SATA port. The SATALED# is an active-low open-drain output. When SATALED# is low, the LED should be active. When SATALED# is high, the LED should be inactive. 200 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.16.10 AHCI Operation The ICH9 provides hardware support for Advanced Host Controller Interface (AHCI), a programming interface for SATA host controllers developed through a joint industry effort. AHCI defines transactions between the SATA controller and software and enables advanced performance and usability with SATA. Platforms supporting AHCI may take advantage of performance features such as no master/slave designation for SATA devices—each device is treated as a master—and hardware assisted native command queuing. AHCI also provides usability enhancements such as Hot-Plug. AHCI requires appropriate software support (e.g., an AHCI driver) and for some features, hardware support in the SATA device or additional platform hardware. The ICH9 supports all of the mandatory features of the Serial ATA Advanced Host Controller Interface Specification, Revision 1.2 and many optional features, such as hardware assisted native command queuing, aggressive power management, LED indicator support, and Hot-Plug through the use of interlock switch support (additional platform hardware and software may be required depending upon the implementation). Note: For reliable device removal notification while in AHCI operation without the use of interlock switches (surprise removal), interface power management should be disabled for the associated port. See Section 7.3.1 of the AHCI Specification for more information. 5.16.11 Serial ATA Reference Clock Low Power Request (SATACLKREQ#) The 100 MHz Serial ATA Reference Clock (SATACLKP, SATACLKN) is implemented on the system as a ground-terminated low-voltage differential signal pair driven by the system Clock Chip. When all the SATA links are in Slumber or disabled, the SATA Reference Clock is not needed and may be stopped and tri-stated at the clock chip allowing system-level power reductions. The ICH9 uses the SATACLKREQ# output signal to communicate with the system Clock Chip to request either SATA clock running or to tell the system clock chip that it can stop the SATA Reference Clock. ICH9 drives this signal low to request clock running, and tristates the signal to indicate that the SATA Reference Clock may be stopped (the ICH9 never drives the pin high). When the SATACLKREQ# is tristated by the ICH9, the clock chip may stop the SATA Reference Clock within 100 ns, anytime after 100 ns, or not at all. If the SATA Reference Clock is not already running, it will start within 100 ns after a SATACLKREQ# is driven low by the ICH9. To enable SATA Reference Clock Low Power Request: 1. Configure GPIO35 to native function 2. Set SATA Clock Request Enable (SCRE) bit to ‘1’ (Dev 31:F2:Offset 94h:bit 28). Note: The reset default for SATACLKREQ# is low to insure that the SATA Reference Clock is running after system reset. 5.16.12 SGPIO Signals The SGPIO signals, in accordance to the SFF-8485 specification, support per-port LED signaling. These signals are not related to SATALED#, which allows for simplified indication of SATA command activity. The SGPIO group interfaces with an external controller chip that fetches and serializes the data for driving across the SGPIO bus. The output signals then control the LEDs. This feature is only valid in AHCI/RAID mode. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 201 Functional Description 5.16.12.1 Mechanism The enclosure management for SATA Controller 1 (Device 31: Function 2) involves sending messages that control LEDs in the enclosure. The messages for this function are stored after the normal registers in the AHCI BAR, at Offset 400h bytes for ICH9 from the beginning of the AHCI BAR as specified by the EM_LOC global register (Section 14.4.1.8). Software creates messages for transmission in the enclosure management message buffer. The data in the message buffer should not be changed if CTL.TM bit is set by software to transmit an update message. Software should only update the message buffer when CTL.TM bit is cleared by hardware otherwise the message transmitted will be indeterminate. Software then writes a register to cause hardware to transmit the message or take appropriate action based on the message content. The software should only create message types supported by the controller, which is LED messages for ICH9. If the software creates other non LED message types (e.g. SAF-TE, SES-2), the SGPIO interface may hang and the result is indeterminate. During reset all SGPIO pins will be in tri-state state. The interface will continue to be in tri-state state after reset until the first transmission occurs when software programs the message buffer and sets the transmit bit CTL.TM. The SATA Host controller will initiate the transmission by driving SCLOCK and at the same time drive the SLOAD to ‘0’ prior to the actual bit stream transmission. The Host will drive SLOAD low for at least 5 SCLOCK then only start the bit stream by driving the SLOAD to high. SLOAD will be driven high for 1 SCLOCK follow by vendor specific pattern that is default to “0000” if software has yet to program the value. A total of 18-bit stream from 6 ports (Port0, Port1, Port2, Port3, Port4 and Port5) of 3-bit per port LED message will be transmitted on SDATAOUT0 pin after the SLOAD is driven high for 1 SCLOCK. Only 2 ports (port4 and port5) of 6 bit total LED message follow by 12 bits of tri-state value will be transmitted out on SDATAOUT1 pin. All the default LED message values will be high prior to software setting them, except the Activity LED message that is configured to be hardware driven that will be generated based on the activity from the respective port. All the LED message values will be driven to ‘1’ for the port that is unimplemented as indicated in the Port Implemented register regardless of the software programmed value through the message buffer. There are 2 different ways of resetting ICH SGPIO interface, asynchronous reset and synchronous reset. Asynchronous reset is caused by platform reset to cause the SGPIO interface to be tri-state asynchronously. Synchronous reset is caused by setting the CTL.RESET bit, clearing the GHC.AE bit or HBA reset, where Host Controller will complete the existing full bit stream transmission then only tri-state all the SGPIO pins. After the reset, both synchronous and asynchronous, the SGPIO pins will stay tristated. Note: ICH Host Controller does not ensure to cause the target SGPIO device or controller to be reset. Software is responsible to keep ICH SGPIO interface in tri-state stated for 2 second in order to cause a reset on the target of the SGPIO interface. 5.16.12.2 Message Format Messages shall be constructed with a one Dword header that describes the message to be sent followed by the actual message contents. The first Dword shall be constructed as follows: 202 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Bit 31:28 Description Reserved Message Type (MTYPE): Specifies the type of the message. The message types are: 0h = LED 27:24 1h = SAF-TE 2h = SES-2 3h = SGPIO (register based interface) All other values reserved 23:16 Data Size (DSIZE): Specifies the data size in bytes. If the message (enclosure services command) has a data buffer that is associated with it that is transferred, the size of that data buffer is specified in this field. If there is no separate data buffer, this field shall have a value of ‘0’. The data directly follows the message in the message buffer. For ICH9, this value should always be ‘0’. 15:8 Message Size (MSIZE): Specifies the size of the message in bytes. The message size does not include the one Dword header. A value of ‘0’ is invalid. For ICH9, the message size is always 4 bytes. 7:0 Reserved The SAF-TE, SES-2, and SGPIO message formats are defined in the corresponding specifications, respectively. The LED message type is defined in Section 5.16.12.3. It is the responsibility of software to ensure the content of the message format is correct. If the message type is not programmed as 'LED' for this controller, the controller shall not take any action to update its LEDs. Note that for LED message type, the message size is always consisted of 4 bytes. 5.16.12.3 LED Message Type The LED message type specifies the status of up to three LEDs. Typically, the usage for these LEDs is activity, fault, and locate. Not all implementations necessarily contain all LEDs (for example, some implementations may not have a locate LED). The message identifies the HBA port number and the Port Multiplier port number that the slot status applies to. If a Port Multiplier is not in use with a particular device, the Port Multiplier port number shall be ‘0’. The format of the LED message type is defined in Table 5-42. The LEDs shall retain their values until there is a following update for that particular slot. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 203 Functional Description Table 5-42. Multi-activity LED Message Type Byte Description Value (VAL): This field describes the state of each LED for a particular location. There are three LEDs that may be supported by the HBA. Each LED has 3 bits of control. LED values are: 000b - LED shall be off 001b - LED shall be solid on as perceived by human eye All other values reserved The LED bit locations are: Bits 2:0 - Activity LED (may be driven by hardware) Bits 5:3 - Vendor Specific LED (e.g. locate) 3-2 Bits 8:6 - Vendor Specific LED (e.g. fault) Bits 15:9 - Reserved Vendor specific message is: Bit 3:0 - Vendor Specific Pattern Bit 15:4 - Reserved Note: If Activity LED Hardware Driven (ATTR.ALHD) bit is set, host will output the hardware LED value sampled internally and will ignore software written activity value on bit [2:0]. Since ICH9 Enclosure Management does not support port multiplier based LED message, the LED message will be generated independently based on respective port’s operation activity. Vendor specific LED values Locate (Bits 5:3) and Fault (Bits 8:6) always are driven by software. Port Multiplier Information: Specifies slot specific information related to Port Multiplier. 1 Bits 3:0 specify the Port Multiplier port number for the slot that requires the status update. If a Port Multiplier is not attached to the device in the affected slot, the Port Multiplier port number shall be '0'. Bits 7:4 are reserved. ICH9 does not support LED messages for devices behind a Port MUltiplier. This byte should be 0. HBA Information: Specifies slot specific information related to the HBA. Bits 4:0 - HBA port number for the slot that requires the status update. 0 Bit 5 - If set to '1', Value is a vendor specific message that applies to the entire enclosure. If cleared to '0', Value applies to the port specified in bits 4:0. Bits 7:6 - Reserved 204 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.16.12.4 SGPIO Waveform Figure 5-12. Serial Data transmitted over the SGPIO Interface Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 205 Functional Description 5.16.13 External SATA ICH9 supports external SATA. External SATA utilizes the SATA interface outside of the system box. The usage model for this feature must comply with the Serial ATA II Cables and Connectors Volume 2 Gold specification at www.sata-io.org. Intel validates two configurations: 1. The cable-up solution involves an internal SATA cable that connects to the SATA motherboard connector and spans to a back panel PCI bracket with an e-SATA connector. A separate e-SATA cable is required to connect an e-SATA device. 2. The back-panel solution involves running a trace to the I/O back panel and connecting a device via an external SATA connector on the board. 5.17 High Precision Event Timers This function provides a set of timers that can be used by the operating system. The timers are defined such that in the future, the operating system may be able to assign specific timers to used directly by specific applications. Each timer can be configured to cause a separate interrupt. ICH9 provides four timers. The four timers are implemented as a single counter each with its own comparator and value register. This counter increases monotonically. Each individual timer can generate an interrupt when the value in its value register matches the value in the main counter. The registers associated with these timers are mapped to a memory space (much like the I/O APIC). However, it is not implemented as a standard PCI function. The BIOS reports to the operating system the location of the register space. The hardware can support an assignable decode space; however, the BIOS sets this space prior to handing it over to the operating system (See Section 9.4). It is not expected that the operating system will move the location of these timers once it is set by the BIOS. 5.17.1 Timer Accuracy 1. The timers are accurate over any 1 ms period to within 0.05% of the time specified in the timer resolution fields. 2. Within any 100 microsecond period, the timer reports a time that is up to two ticks too early or too late. Each tick is less than or equal to 100 ns, so this represents an error of less than 0.2%. 3. The timer is monotonic. It does not return the same value on two consecutive reads (unless the counter has rolled over and reached the same value). The main counter is clocked by the 14.31818 MHz clock, synchronized into the 66.666 MHz domain. This results in a non-uniform duty cycle on the synchronized clock, but does have the correct average period. The accuracy of the main counter is as accurate as the 14.3818 MHz clock. 5.17.2 Interrupt Mapping Mapping Option #1 (Legacy Replacement Option) In this case, the Legacy Replacement Rout bit (LEG_RT_CNF) is set. This forces the mapping found in Table 5-43. 206 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-43. Legacy Replacement Routing Timer 8259 Mapping APIC Mapping Comment 0 IRQ0 IRQ2 In this case, the 8254 timer will not cause any interrupts 1 IRQ8 IRQ8 In this case, the RTC will not cause any interrupts. 2&3 Per IRQ Routing Field. Per IRQ Routing Field Mapping Option #2 (Standard Option) In this case, the Legacy Replacement Rout bit (LEG_RT_CNF) is 0. Each timer has its own routing control. The interrupts can be routed to various interrupts in the 8259 or I/O APIC. A capabilities field indicates which interrupts are valid options for routing. If a timer is set for edge-triggered mode, the timers should not be share with any PCI interrupts. For the Intel ICH9, the only supported interrupt values are as follows: Timer 0 and 1: IRQ20, 21, 22 & 23 (I/O APIC only). Timer 2: IRQ11 (8259 or I/O APIC) and IRQ20, 21, 22 & 23 (I/O APIC only). Timer 3: IRQ12 (8259 or I/O APIC) and IRQ 20, 21, 22 & 23 (I/O APIC only). 5.17.3 Periodic vs. Non-Periodic Modes Non-Periodic Mode Timer 0 is configurable to 32 (default) or 64-bit mode, whereas Timers 1, 2 and 3 only support 32-bit mode (See Section 21.1.5). All four timers support non-periodic mode. Consult Section 2.3.9.2.1 of the IA-PC HPET Specification for a description of this mode. Periodic Mode Timer 0 is the only timer that supports periodic mode. Consult Section 2.3.9.2.2 of the IA-PC HPET Specification for a description of this mode. The following usage model is expected: 1. Software clears the ENABLE_CNF bit to prevent any interrupts 2. Software Clears the main counter by writing a value of 00h to it. 3. Software sets the TIMER0_VAL_SET_CNF bit. 4. Software writes the new value in the TIMER0_COMPARATOR_VAL register 5. Software sets the ENABLE_CNF bit to enable interrupts. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 207 Functional Description The Timer 0 Comparator Value register cannot be programmed reliably by a single 64-bit write in a 32-bit environment except if only the periodic rate is being changed during run-time. If the actual Timer 0 Comparator Value needs to be reinitialized, then the following software solution will always work regardless of the environment: 1. Set TIMER0_VAL_SET_CNF bit 2. Set the lower 32 bits of the Timer0 Comparator Value register 3. Set TIMER0_VAL_SET_CNF bit 4. Set the upper 32 bits of the Timer0 Comparator Value register 5.17.4 Enabling the Timers The BIOS or operating system PnP code should route the interrupts. This includes the Legacy Rout bit, Interrupt Rout bit (for each timer), interrupt type (to select the edge or level type for each timer) The Device Driver code should do the following for an available timer: 1. Set the Overall Enable bit (Offset 04h, bit 0). 2. Set the timer type field (selects one-shot or periodic). 3. Set the interrupt enable 4. Set the comparator value 5.17.5 Interrupt Levels Interrupts directed to the internal 8259s are active high. See Section 5.9 for information regarding the polarity programming of the I/O APIC for detecting internal interrupts. If the interrupts are mapped to the 8259 or I/O APIC and set for level-triggered mode, they can be shared with PCI interrupts. They may be shared although it’s unlikely for the operating system to attempt to do this. If more than one timer is configured to share the same IRQ (using the TIMERn_INT_ROUT_CNF fields), then the software must configure the timers to leveltriggered mode. Edge-triggered interrupts cannot be shared. 5.17.6 Handling Interrupts If each timer has a unique interrupt and the timer has been configured for edgetriggered mode, then there are no specific steps required. No read is required to process the interrupt. If a timer has been configured to level-triggered mode, then its interrupt must be cleared by the software. This is done by reading the interrupt status register and writing a 1 back to the bit position for the interrupt to be cleared. Independent of the mode, software can read the value in the main counter to see how time has passed between when the interrupt was generated and when it was first serviced. If Timer 0 is set up to generate a periodic interrupt, the software can check to see how much time remains until the next interrupt by checking the timer value register. 208 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.17.7 Issues Related to 64-Bit Timers with 32-Bit Processors A 32-bit timer can be read directly using processors that are capable of 32-bit or 64-bit instructions. However, a 32-bit processor may not be able to directly read 64-bit timer. A race condition comes up if a 32-bit processor reads the 64-bit register using two separate 32-bit reads. The danger is that just after reading one half, the other half rolls over and changes the first half. If a 32-bit processor needs to access a 64-bit timer, it must first halt the timer before reading both the upper and lower 32-bits of the timer. If a 32-bit processor does not want to halt the timer, it can use the 64-bit timer as a 32-bit timer by setting the TIMERn_32MODE_CNF bit. This causes the timer to behave as a 32-bit timer. The upper 32-bits are always 0. Alternatively, software may do a multiple read of the counter while it is running. Software can read the high 32 bits, then the low 32 bits, the high 32 bits again. If the high 32 bits have not changed between the two reads, then a rollover has not happened and the low 32 bits are valid. If the high 32 bits have changed between reads, then the multiple reads are repeated until a valid read is performed. Note: On a 64-bit platform, if software attempts a 64 bit read of the 64-bit counter, software must be aware that some platforms may split the 64 bit read into two 32 bit reads. The read maybe inaccurate if the low 32 bits roll over between the high and low reads. 5.18 USB UHCI Host Controllers (D29:F0, F1, F2, F3 and D26:F0, F1 and F2) The ICH9 contains six USB full/low-speed host controllers that support the standard Universal Host Controller Interface (UHCI), Revision 1.1. Each UHCI Host Controller (UHC) includes a root hub with two separate USB ports each, for a total of twelve USB ports. • Overcurrent detection on all twelve USB ports is supported. The overcurrent inputs are not 5 V tolerant, and can be used as GPIs if not needed. • The ICH9’s UHCI host controllers are arbitrated differently than standard PCI devices to improve arbitration latency. • The UHCI controllers use the Analog Front End (AFE) embedded cell that allows support for USB full-speed signaling rates, instead of USB I/O buffers. Note: D26:F2 can be configured as D29:F3 during BIOS Post. 5.18.1 Data Structures in Main Memory Section 3.1 - 3.3 of the Universal Host Controller Interface Specification, Revision 1.1 details the data structures used to communicate control, status, and data between software and the ICH9. 5.18.2 Data Transfers to/from Main Memory Section 3.4 of the Universal Host Controller Interface Specification, Revision 1.1 describes the details on how HCD and the ICH9 communicate via the Schedule data structures. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 209 Functional Description 5.18.3 Data Encoding and Bit Stuffing The ICH9 USB employs NRZI data encoding (Non-Return to Zero Inverted) when transmitting packets. Full details on this implementation are given in the Universal Serial Bus Specification, Revision 2.0. 5.18.4 Bus Protocol 5.18.4.1 Bit Ordering Bits are sent out onto the bus least significant bit (LSb) first, followed by next LSb, through to the most significant bit (MSb) last. 5.18.4.2 SYNC Field All packets begin with a synchronization (SYNC) field, which is a coded sequence that generates a maximum edge transition density. The SYNC field appears on the bus as IDLE followed by the binary string “KJKJKJKK,” in its NRZI encoding. It is used by the input circuitry to align incoming data with the local clock and is defined to be 8 bits in length. SYNC serves only as a synchronization mechanism. The last two bits in the SYNC field are a marker that is used to identify the first bit of the PID. All subsequent bits in the packet must be indexed from this point. 5.18.4.3 Packet Field Formats All packets have distinct start and end of packet delimiters. Full details are given in the Universal Serial Bus Specification, Revision 2.0, in Section 8.3.1. 5.18.4.4 Address Fields Function endpoints are addressed using the function address field and the endpoint field. Full details on this are given in the Universal Serial Bus Specification, Revision 2.0, in Section 8.3.2. 5.18.4.5 Frame Number Field The frame number field is an 11-bit field that is incremented by the host on a per frame basis. The frame number field rolls over upon reaching its maximum value of 7FFh, and is sent only for SOF tokens at the start of each frame. 5.18.4.6 Data Field The data field may range from 0 to 1023 bytes and must be an integral numbers of bytes. Data bits within each byte are shifted out LSB first. 5.18.4.7 Cyclic Redundancy Check (CRC) CRC is used to protect the all non-PID fields in token and data packets. In this context, these fields are considered to be protected fields. Full details on this are given in the Universal Serial Bus Specification, Revision 2.0, in Section 8.3.5. 5.18.5 Packet Formats The USB protocol calls out several packet types: token, data, and handshake packets. Full details on this are given in the Universal Serial Bus Specification, Revision 2.0, in section 8.4. 210 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.18.6 USB Interrupts There are two general groups of USB interrupt sources, those resulting from execution of transactions in the schedule, and those resulting from an ICH9 operation error. All transaction-based sources can be masked by software through the ICH9’s Interrupt Enable register. Additionally, individual transfer descriptors can be marked to generate an interrupt on completion. When the ICH9 drives an interrupt for USB, it internally drives the PIRQA# pin for USB function #0 and USB function #3, PIRQD# pin for USB function #1, and the PIRQC# pin for USB function #2, until all sources of the interrupt are cleared. In order to accommodate some operating systems, the Interrupt Pin register must contain a different value for each function of this new multi-function device. 5.18.6.1 Transaction-Based Interrupts These interrupts are not signaled until after the status for the last complete transaction in the frame has been written back to host memory. This ensures that software can safely process through (Frame List Current Index -1) when it is servicing an interrupt. CRC Error / Time-Out A CRC/Time-Out error occurs when a packet transmitted from the ICH9 to a USB device or a packet transmitted from a USB device to the ICH9 generates a CRC error. The ICH9 is informed of this event by a time-out from the USB device or by the ICH9’s CRC checker generating an error on reception of the packet. Additionally, a USB bus timeout occurs when USB devices do not respond to a transaction phase within 19-bit times of an EOP. Either of these conditions causes the C_ERR field of the TD to decrement. When the C_ERR field decrements to 0, the following occurs: • The Active bit in the TD is cleared • The Stalled bit in the TD is set • The CRC/Time-out bit in the TD is set. • At the end of the frame, the USB Error Interrupt bit is set in the HC status register. If the CRC/Time out interrupt is enabled in the Interrupt Enable register, a hardware interrupt will be signaled to the system. Interrupt on Completion Transfer Descriptors contain a bit that can be set to cause an interrupt on their completion. The completion of the transaction associated with that block causes the USB Interrupt bit in the HC Status Register to be set at the end of the frame in which the transfer completed. When a TD is encountered with the IOC bit set to 1, the IOC bit in the HC Status register is set to 1 at the end of the frame if the active bit in the TD is set to 0 (even if it was set to 0 when initially read). If the IOC Enable bit of Interrupt Enable register (bit 2 of I/O offset 04h) is set, a hardware interrupt is signaled to the system. The USB Interrupt bit in the HC status register is set either when the TD completes successfully or because of errors. If the completion is because of errors, the USB Error bit in the HC status register is also set. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 211 Functional Description Short Packet Detect A transfer set is a collection of data which requires more than one USB transaction to completely move the data across the USB. An example might be a large print file which requires numerous TDs in multiple frames to completely transfer the data. Reception of a data packet that is less than the endpoint’s Max Packet size during Control, Bulk or Interrupt transfers signals the completion of the transfer set, even if there are active TDs remaining for this transfer set. Setting the SPD bit in a TD indicates to the HC to set the USB Interrupt bit in the HC status register at the end of the frame in which this event occurs. This feature streamlines the processing of input on these transfer types. If the Short Packet Interrupt Enable bit in the Interrupt Enable register is set, a hardware interrupt is signaled to the system at the end of the frame where the event occurred. Serial Bus Babble When a device transmits on the USB for a time greater than its assigned Max Length, it is said to be babbling. Since isochrony can be destroyed by a babbling device, this error results in the Active bit in the TD being cleared to 0 and the Stalled and Babble bits being set to 1. The C_ERR field is not decremented for a babble. The USB Error Interrupt bit in the HC Status register is set to 1 at the end of the frame. A hardware interrupt is signaled to the system. If an EOF babble was caused by the ICH9 (due to incorrect schedule for instance), the ICH9 forces a bit stuff error followed by an EOP and the start of the next frame. Stalled This event indicates that a device/endpoint returned a STALL handshake during a transaction or that the transaction ended in an error condition. The TDs Stalled bit is set and the Active bit is cleared. Reception of a STALL does not decrement the error counter. A hardware interrupt is signaled to the system. Data Buffer Error This event indicates that an overrun of incoming data or a under-run of outgoing data has occurred for this transaction. This would generally be caused by the ICH9 not being able to access required data buffers in memory within necessary latency requirements. Either of these conditions causes the C_ERR field of the TD to be decremented. When C_ERR decrements to 0, the Active bit in the TD is cleared, the Stalled bit is set, the USB Error Interrupt bit in the HC Status register is set to 1 at the end of the frame and a hardware interrupt is signaled to the system. Bit Stuff Error A bit stuff error results from the detection of a sequence of more that six 1s in a row within the incoming data stream. This causes the C_ERR field of the TD to be decremented. When the C_ERR field decrements to 0, the Active bit in the TD is cleared to 0, the Stalled bit is set to 1, the USB Error Interrupt bit in the HC Status register is set to 1 at the end of the frame and a hardware interrupt is signaled to the system. 212 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.18.6.2 Non-Transaction Based Interrupts If an ICH9 process error or system error occurs, the ICH9 halts and immediately issues a hardware interrupt to the system. Resume Received This event indicates that the ICH9 received a RESUME signal from a device on the USB bus during a global suspend. If this interrupt is enabled in the Interrupt Enable register, a hardware interrupt is signaled to the system allowing the USB to be brought out of the suspend state and returned to normal operation. ICH9 Process Error The HC monitors certain critical fields during operation to ensure that it does not process corrupted data structures. These include checking for a valid PID and verifying that the MaxLength field is less than 1280. If it detects a condition that would indicate that it is processing corrupted data structures, it immediately halts processing, sets the HC Process Error bit in the HC Status register and signals a hardware interrupt to the system. This interrupt cannot be disabled through the Interrupt Enable register. Host System Error The ICH9 sets this bit to 1 when a Parity error, Master Abort, or Target Abort occurs. When this error occurs, the ICH9 clears the Run/Stop bit in the Command register to prevent further execution of the scheduled TDs. This interrupt cannot be disabled through the Interrupt Enable register. 5.18.7 USB Power Management The Host controller can be put into a suspended state and its power can be removed. This requires that certain bits of information are retained in the suspend power plane of the ICH9 so that a device on a port may wake the system. Such a device may be a faxmodem, which will wake up the machine to receive a fax or take a voice message. The settings of the following bits in I/O space will be maintained when the ICH9 enters the S3, S4, or S5 states. Table 5-44. Bits Maintained in Low Power States Register Offset Bit Command 00h 3 Enter Global Suspend Mode (EGSM) Status 02h 2 Resume Detect Port Status and Control 10h & 12h Description 2 Port Enabled/Disabled 6 Resume Detect 8 Low-speed Device Attached 12 Suspend When the ICH9 detects a resume event on any of its ports, it sets the corresponding USB_STS bit in ACPI space. If USB is enabled as a wake/break event, the system wakes up and an SCI generated. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 213 Functional Description 5.18.8 USB Legacy Keyboard Operation When a USB keyboard is plugged into the system, and a standard keyboard is not, the system may not boot, and MS-DOS legacy software will not run, because the keyboard will not be identified. The ICH9 implements a series of trapping operations which will snoop accesses that go to the keyboard controller, and put the expected data from the USB keyboard into the keyboard controller. Note: The scheme described below assumes that the keyboard controller (8042 or equivalent) is on the LPC bus. This legacy operation is performed through SMM space. Figure 5-13 shows the Enable and Status path. The latched SMI source (60R, 60W, 64R, 64W) is available in the Status Register. Because the enable is after the latch, it is possible to check for other events that didn't necessarily cause an SMI. It is the software's responsibility to logically AND the value with the appropriate enable bits. Note also that the SMI is generated before the PCI cycle completes (e.g., before TRDY# goes active) to ensure that the processor doesn't complete the cycle before the SMI is observed. The logic also needs to block the accesses to the 8042. If there is an external 8042, then this is simply accomplished by not activating the 8042 CS. This is done by logically ANDing the four enables (60R, 60W, 64R, 64W) with the 4 types of accesses to determine if 8042CS should go active. An additional term is required for the “passthrough” case. The state table for Figure 5-13 is shown in Table 5-45. Figure 5-13. USB Legacy Keyboard Flow Diagram To Individual "Caused By" "Bits" 60 READ KBC Accesses S D PCI Config Comb. Decoder Clear SMI_60_R AND R EN_SMI_ON_60R Read, Write SMI Same for 60W, 64R, 64W OR EN_PIRQD# AND To PIRQD# To "Caused By" Bit USB_IRQ S Clear USB_IRQ D R AND EN_SMI_ON_IRQ 214 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-45. USB Legacy Keyboard State Transitions Current State Action Data Value Next State IDLE 64h / Write D1h GateState1 Standard D1 command. Cycle passed through to 8042. SMI# doesn't go active. PSTATE (offset C0, bit 6) goes to 1. IDLE 64h / Write Not D1h IDLE Bit 3 in Config Register determines if cycle passed through to 8042 and if SMI# generated. IDLE 64h / Read N/A IDLE Bit 2 in Config Register determines if cycle passed through to 8042 and if SMI# generated. IDLE 60h / Write Don't Care IDLE Bit 1 in Config Register determines if cycle passed through to 8042 and if SMI# generated. IDLE 60h / Read N/A IDLE Bit 0 in Config Register determines if cycle passed through to 8042 and if SMI# generated. GateState1 60h / Write GateState2 Cycle passed through to 8042, even if trap enabled in Bit 1 in Config Register. No SMI# generated. PSTATE remains 1. If data value is not DFh or DDh then the 8042 may chose to ignore it. GateState1 Cycle passed through to 8042, even if trap enabled via Bit 3 in Config Register. No SMI# generated. PSTATE remains 1. Stay in GateState1 because this is part of the double-trigger sequence. ILDE Bit 3 in Config space determines if cycle passed through to 8042 and if SMI# generated. PSTATE goes to 0. If Bit 7 in Config Register is set, then SMI# should be generated. GateState1 GateState1 XXh 64h / Write 64h / Write D1h Not D1h Comment GateState1 60h / Read N/A IDLE This is an invalid sequence. Bit 0 in Config Register determines if cycle passed through to 8042 and if SMI# generated. PSTATE goes to 0. If Bit 7 in Config Register is set, then SMI# should be generated. GateState1 64h / Read N/A GateState1 Just stay in same state. Generate an SMI# if enabled in Bit 2 of Config Register. PSTATE remains 1. IDLE Standard end of sequence. Cycle passed through to 8042. PSTATE goes to 0. Bit 7 in Config Space determines if SMI# should be generated. IDLE Improper end of sequence. Bit 3 in Config Register determines if cycle passed through to 8042 and if SMI# generated. PSTATE goes to 0. If Bit 7 in Config Register is set, then SMI# should be generated. GateState2 64 / Write GateState2 64h / Write FFh Not FFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 215 Functional Description Table 5-45. USB Legacy Keyboard State Transitions Current State Action Data Value Next State Comment GateState2 64h / Read N/A GateState2 Just stay in same state. Generate an SMI# if enabled in Bit 2 of Config Register. PSTATE remains 1. GateState2 60h / Write IDLE Improper end of sequence. Bit 1 in Config Register determines if cycle passed through to 8042 and if SMI# generated. PSTATE goes to 0. If Bit 7 in Config Register is set, then SMI# should be generated. IDLE Improper end of sequence. Bit 0 in Config Register determines if cycle passed through to 8042 and if SMI# generated. PSTATE goes to 0. If Bit 7 in Config Register is set, then SMI# should be generated. GateState2 5.18.9 60h / Read XXh N/A Function Level Reset Support (FLR) The USB UHCI Controllers support the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel® Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a PCI reset was asserted. 5.18.9.1 FLR Steps 5.18.9.1.1 FLR Initialization 1. A FLR is initiated by software writing a 1 to the Initiate FLR bit. 2. All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.18.9.1.2 FLR Operation The Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 5.18.9.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: 216 From the time Initiate FLR bit is written to 1, software must wait at least 100 ms before accessing the function. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.19 USB EHCI Host Controllers (D29:F7 and D26:F7) The ICH9 contains two Enhanced Host Controller Interface (EHCI) host controllers which support up to twelve USB 2.0 high-speed root ports. USB 2.0 allows data transfers up to 480 Mb/s using the same pins as the twelve USB full-speed/low-speed ports. The ICH9 contains port-routing logic that determines whether a USB port is controlled by one of the UHCI controllers or by one of the EHCI controllers. USB 2.0 based Debug Port is also implemented in the ICH9. A summary of the key architectural differences between the USB UHCI host controllers and the EHCI host controller are shown in Table 5-46. Table 5-46. UHCI vs. EHCI Parameter 5.19.1 USB UHCI USB EHCI Accessible by I/O space Memory Space Memory Data Structure Single linked list Separated into Periodic and Asynchronous lists Differential Signaling Voltage 3.3 V 400 mV Ports per Controller 2 6 or 8 (controller #1) and 6 or 4 (Controller #2) EHC Initialization The following descriptions step through the expected ICH9 Enhanced Host Controller (EHC) initialization sequence in chronological order, beginning with a complete power cycle in which the suspend well and core well have been off. 5.19.1.1 BIOS Initialization BIOS performs a number of platform customization steps after the core well has powered up. Contact your Intel Field Representative for additional ICH9 BIOS information. 5.19.1.2 Driver Initialization See Chapter 4 of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 217 Functional Description 5.19.1.3 EHC Resets In addition to the standard ICH9 hardware resets, portions of the EHC are reset by the HCRESET bit and the transition from the D3HOT device power management state to the D0 state. The effects of each of these resets are: Reset Does Reset HCRESET bit set. Memory space registers except Structural Parameters (which is written by BIOS). Software writes the Device Power State from D3HOT (11b) to D0 (00b). Core well registers (except BIOSprogrammed registers). Does not Reset Comments Configuration registers. The HCRESET must only affect registers that the EHCI driver controls. PCI Configuration space and BIOS-programmed parameters can not be reset. Suspend well registers; BIOSprogrammed core well registers. The D3-to-D0 transition must not cause wake information (suspend well) to be lost. It also must not clear BIOSprogrammed registers because BIOS may not be invoked following the D3-to-D0 transition. If the detailed register descriptions give exceptions to these rules, those exceptions override these rules. This summary is provided to help explain the reasons for the reset policies. 5.19.2 Data Structures in Main Memory See Section 3 and Appendix B of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 for details. 5.19.3 USB 2.0 Enhanced Host Controller DMA The ICH9 USB 2.0 EHC implements three sources of USB packets. They are, in order of priority on USB during each microframe: 1. The USB 2.0 Debug Port (see Section USB 2.0 Based Debug Port), 2. The Periodic DMA engine, and 3. The Asynchronous DMA engine. The ICH9 always performs any currently-pending debug port transaction at the beginning of a microframe, followed by any pending periodic traffic for the current microframe. If there is time left in the microframe, then the EHC performs any pending asynchronous traffic until the end of the microframe (EOF1). Note that the debug port traffic is only presented on one port (Port #0), while the other ports are idle during this time. 5.19.4 Data Encoding and Bit Stuffing See Chapter 8 of the Universal Serial Bus Specification, Revision 2.0. 218 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.19.5 Packet Formats See Chapter 8 of the Universal Serial Bus Specification, Revision 2.0. The ICH9 EHCI allows entrance to USB test modes, as defined in the USB 2.0 specification, including Test J, Test Packet, etc. However note that the ICH9 Test Packet test mode interpacket gap timing may not meet the USB 2.0 specification. 5.19.6 USB 2.0 Interrupts and Error Conditions Section 4 of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 goes into detail on the EHC interrupts and the error conditions that cause them. All error conditions that the EHC detects can be reported through the EHCI Interrupt status bits. Only ICH9-specific interrupt and error-reporting behavior is documented in this section. The EHCI Interrupts Section must be read first, followed by this section of the datasheet to fully comprehend the EHC interrupt and error-reporting functionality. • Based on the EHC’s Buffer sizes and buffer management policies, the Data Buffer Error can never occur on the ICH9. • Master Abort and Target Abort responses from hub interface on EHC-initiated read packets will be treated as Fatal Host Errors. The EHC halts when these conditions are encountered. • The ICH9 may assert the interrupts which are based on the interrupt threshold as soon as the status for the last complete transaction in the interrupt interval has been posted in the internal write buffers. The requirement in the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 (that the status is written to memory) is met internally, even though the write may not be seen on DMI before the interrupt is asserted. • Since the ICH9 supports the 1024-element Frame List size, the Frame List Rollover interrupt occurs every 1024 milliseconds. • The ICH9 delivers interrupts using PIRQH#. • The ICH9 does not modify the CERR count on an Interrupt IN when the “Do Complete-Split” execution criteria are not met. • For complete-split transactions in the Periodic list, the “Missed Microframe” bit does not get set on a control-structure-fetch that fails the late-start test. If subsequent accesses to that control structure do not fail the late-start test, then the “Missed Microframe” bit will get set and written back. 5.19.6.1 Aborts on USB 2.0-Initiated Memory Reads If a read initiated by the EHC is aborted, the EHC treats it as a fatal host error. The following actions are taken when this occurs: • The Host System Error status bit is set • The DMA engines are halted after completing up to one more transaction on the USB interface • If enabled (by the Host System Error Enable), then an interrupt is generated • If the status is Master Abort, then the Received Master Abort bit in configuration space is set • If the status is Target Abort, then the Received Target Abort bit in configuration space is set • If enabled (by the SERR Enable bit in the function’s configuration space), then the Signaled System Error bit in configuration bit is set. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 219 Functional Description 5.19.7 USB 2.0 Power Management 5.19.7.1 Pause Feature This feature allows platforms (especially mobile systems) to dynamically enter lowpower states during brief periods when the system is idle (i.e., between keystrokes). This is useful for enabling power management features like Intel SpeedStep® technology in the ICH9. The policies for entering these states typically are based on the recent history of system bus activity to incrementally enter deeper power management states. Normally, when the EHC is enabled, it regularly accesses main memory while traversing the DMA schedules looking for work to do; this activity is viewed by the power management software as a non-idle system, thus preventing the power managed states to be entered. Suspending all of the enabled ports can prevent the memory accesses from occurring, but there is an inherent latency overhead with entering and exiting the suspended state on the USB ports that makes this unacceptable for the purpose of dynamic power management. As a result, the EHCI software drivers are allowed to pause the EHC’s DMA engines when it knows that the traffic patterns of the attached devices can afford the delay. The pause only prevents the EHC from generating memory accesses; the SOF packets continue to be generated on the USB ports (unlike the suspended state). 5.19.7.2 Suspend Feature The Enhanced Host Controller Interface (EHCI) For Universal Serial Bus Specification, Section 4.3 describes the details of Port Suspend and Resume. 5.19.7.3 ACPI Device States The USB 2.0 function only supports the D0 and D3 PCI Power Management states. Notes regarding the ICH9 implementation of the Device States: 1. The EHC hardware does not inherently consume any more power when it is in the D0 state than it does in the D3 state. However, software is required to suspend or disable all ports prior to entering the D3 state such that the maximum power consumption is reduced. 2. In the D0 state, all implemented EHC features are enabled. 3. In the D3 state, accesses to the EHC memory-mapped I/O range will master abort. Note that, since the Debug Port uses the same memory range, the Debug Port is only operational when the EHC is in the D0 state. 4. In the D3 state, the EHC interrupt must never assert for any reason. The internal PME# signal is used to signal wake events, etc. 5. When the Device Power State field is written to D0 from D3, an internal reset is generated. See section EHC Resets for general rules on the effects of this reset. 6. Attempts to write any other value into the Device Power State field other than 00b (D0 state) and 11b (D3 state) will complete normally without changing the current value in this field. 220 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.19.7.4 ACPI System States The EHC behavior as it relates to other power management states in the system is summarized in the following list: — The System is always in the S0 state when the EHC is in the D0 state. However, when the EHC is in the D3 state, the system may be in any power management state (including S0). — When in D0, the Pause feature (See Section 5.19.7.1) enables dynamic processor low-power states to be entered. — The PLL in the EHC is disabled when entering the S3/S4/S5 states (core power turns off). — All core well logic is reset in the S3/S4/S5 states. 5.19.7.5 Mobile Considerations The ICH9 USB 2.0 implementation does not behave differently in the mobile configurations versus the desktop configurations. However, some features may be especially useful for the mobile configurations. • If a system (e.g., mobile) does not implement all twelve USB 2.0 ports, the ICH9 provides mechanisms for changing the structural parameters of the EHC and hiding unused UHCI controllers. See the Intel® ICH9 BIOS Specification for information on how BIOS should configure the ICH9. • Mobile systems may want to minimize the conditions that will wake the system. The ICH9 implements the “Wake Enable” bits in the Port Status and Control registers, as specified in the EHCI spec, for this purpose. • Mobile systems may want to cut suspend well power to some or all USB ports when in a low-power state. The ICH9 implements the optional Port Wake Capability Register in the EHC Configuration Space for this platform-specific information to be communicated to software. 5.19.8 Interaction with UHCI Host Controllers The Enhanced Host controllers share its ports with UHCI Host controllers in the ICH9. The UHC at D29:F0 shares ports 0 and 1; the UHC at D29:F1 shares ports 2 and 3; the UHC at D29:F2 shares ports 4 and 5 with the EHC at D29:F7, while the UHC at D26:F0 shares ports 6 and 7, the UHC at D26:F1 shares ports 8 and 9, and the UHC at D26:F2 shares ports 10 and 11 with EHC at D26:F7. There is very little interaction between the Enhanced and the UHCI controllers other than the muxing control which is provided as part of the EHC. Figure 5-14 shows the USB Port Connections at a conceptual level. Note: D26:F2 can be configured as D29:F3 during BIOS post. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 221 Functional Description 5.19.8.1 Port-Routing Logic Integrated into the EHC functionality is port-routing logic, which performs the muxing between the UHCI and EHCI host controllers. The ICH9 conceptually implements this logic as described in Section 4.2 of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0. If a device is connected that is not capable of USB 2.0’s high-speed signaling protocol or if the EHCI software drivers are not present as indicated by the Configured Flag, then the UHCI controller owns the port. Owning the port means that the differential output is driven by the owner and the input stream is only visible to the owner. The host controller that is not the owner of the port internally sees a disconnected port. Figure 5-14. Intel® ICH9-USB Port Connections Default Six and Six Configuration EHCI #1 UHCI Port 0 Port 1 EHCI #2 UHCI UHCI UHCI Port 2 Port 3 Port 4 Port 5 UHCI Port 6 Port 7 UHCI Port 8 Port 9 UHCI UHCI Port 10 Port 11 Figure 5-15. Intel® ICH9-USB Port Connections Eight and Four Configuration EHCI #1 UHCI Port 0 Port 1 UHCI Port 2 Port 3 UHCI UHCI Port 4 Port 5 EHCI #2 UHCI Port 10 Port 11 UHCI Port 6 Port 7 UHCI UHCI Port 8 Port 9 Note that the port-routing logic is the only block of logic within the ICH9 that observes the physical (real) connect/disconnect information. The port status logic inside each of the host controllers observes the electrical connect/disconnect information that is generated by the port-routing logic. Only the differential signal pairs are multiplexed/de-multiplexed between the UHCI and EHCI host controllers. The other USB functional signals are handled as follows: • The Overcurrent inputs (OC[11:0]#) are directly routed to both controllers. An overcurrent event is recorded in both controllers’ status registers. 222 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description The Port-Routing logic is implemented in the Suspend power well so that reenumeration and re-mapping of the USB ports is not required following entering and exiting a system sleep state in which the core power is turned off. The ICH9 also allows the USB Debug Port traffic to be routed in and out of Port #0 and Port#6. When in this mode, the Enhanced Host controller is the owner of Port #0 and Port#6. 5.19.8.2 Device Connects The Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 describes the details of handling Device Connects in Section 4.2. There are four general scenarios that are summarized below. 1. Configure Flag = 0 and a full-speed/low-speed-only Device is connected — In this case, the UHC is the owner of the port both before and after the connect occurs. The EHC (except for the port-routing logic) never sees the connect occur. The UHCI driver handles the connection and initialization process. 2. Configure Flag = 0 and a high-speed-capable Device is connected — In this case, the UHC is the owner of the port both before and after the connect occurs. The EHC (except for the port-routing logic) never sees the connect occur. The UHCI driver handles the connection and initialization process. Since the UHC does not perform the high-speed chirp handshake, the device operates in compatible mode. 3. Configure Flag = 1 and a full-speed/low-speed-only Device is connected — In this case, the EHC is the owner of the port before the connect occurs. The EHCI driver handles the connection and performs the port reset. After the reset process completes, the EHC hardware has cleared (not set) the Port Enable bit in the EHC’s PORTSC register. The EHCI driver then writes a 1 to the Port Owner bit in the same register, causing the UHC to see a connect event and the EHC to see an “electrical” disconnect event. The UHCI driver and hardware handle the connection and initialization process from that point on. The EHCI driver and hardware handle the perceived disconnect. 4. Configure Flag = 1 and a high-speed-capable Device is connected — In this case, the EHC is the owner of the port before, and remains the owner after, the connect occurs. The EHCI driver handles the connection and performs the port reset. After the reset process completes, the EHC hardware has set the Port Enable bit in the EHC’s PORTSC register. The port is functional at this point. The UHC continues to see an unconnected port. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 223 Functional Description 5.19.8.3 Device Disconnects The Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 describes the details of handling Device Connects in Section 4.2. There are three general scenarios that are summarized below. 1. Configure Flag = 0 and the device is disconnected — In this case, the UHC is the owner of the port both before and after the disconnect occurs. The EHC (except for the port-routing logic) never sees a device attached. The UHCI driver handles disconnection process. 2. Configure Flag = 1 and a full-speed/low-speed-capable Device is disconnected — In this case, the UHC is the owner of the port before the disconnect occurs. The disconnect is reported by the UHC and serviced by the associated UHCI driver. The port-routing logic in the EHC cluster forces the Port Owner bit to 0, indicating that the EHC owns the unconnected port. 3. Configure Flag = 1 and a high-speed-capable Device is disconnected — In this case, the EHC is the owner of the port before, and remains the owner after, the disconnect occurs. The EHCI hardware and driver handle the disconnection process. The UHC never sees a device attached. 5.19.8.4 Effect of Resets on Port-Routing Logic As mentioned above, the Port Routing logic is implemented in the suspend power well so that remuneration and re-mapping of the USB ports is not required following entering and exiting a system sleep state in which the core power is turned off. Reset Event Suspend Well Reset Core Well Reset D3-to-D0 Reset HCRESET 5.19.9 Effect on Configure Flag Effect on Port Owner Bits cleared (0) set (1) no effect no effect no effect no effect cleared (0) set (1) USB 2.0 Legacy Keyboard Operation The ICH9 must support the possibility of a keyboard downstream from either a fullspeed/low-speed or a high-speed port. The description of the legacy keyboard support is unchanged from USB 1.1 (See Section 5.18.8). The EHC provides the basic ability to generate SMIs on an interrupt event, along with more sophisticated control of the generation of SMIs. 224 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.19.10 USB 2.0 Based Debug Port The ICH9 supports the elimination of the legacy COM ports by providing the ability for new debugger software to interact with devices on a USB 2.0 port. High-level restrictions and features are: • Operational before USB 2.0 drivers are loaded. • Functions even when the port is disabled. • Works even though non-configured port is default-routed to the UHCI. Note that the Debug Port can not be used to debug an issue that requires a full-speed/lowspeed device on Port #0 using the UHCI drivers. • Allows normal system USB 2.0 traffic in a system that may only have one USB port. • Debug Port device (DPD) must be high-speed capable and connect directly to Port #0 and Port#6 on ICH9 systems (e.g., the DPD cannot be connected to Port #0/Port#6 through a hub). • Debug Port FIFO always makes forward progress (a bad status on USB is simply presented back to software). • The Debug Port FIFO is only given one USB access per microframe. The Debug port facilitates operating system and device driver debug. It allows the software to communicate with an external console using a USB 2.0 connection. Because the interface to this link does not go through the normal USB 2.0 stack, it allows communication with the external console during cases where the operating system is not loaded, the USB 2.0 software is broken, or where the USB 2.0 software is being debugged. Specific features of this implementation of a debug port are: • Only works with an external USB 2.0 debug device (console) • Implemented for a specific port on the host controller • Operational anytime the port is not suspended AND the host controller is in D0 power state. • Capability is interrupted when port is driving USB RESET 5.19.10.1 Theory of Operation There are two operational modes for the USB debug port: 1. Mode 1 is when the USB port is in a disabled state from the viewpoint of a standard host controller driver. In Mode 1, the Debug Port controller is required to generate a “keepalive” packets less than 2 ms apart to keep the attached debug device from suspending. The keepalive packet should be a standalone 32-bit SYNC field. 2. Mode 2 is when the host controller is running (i.e., host controller’s Run/Stop# bit is 1). In Mode 2, the normal transmission of SOF packets will keep the debug device from suspending. Behavioral Rules 1. In both modes 1 and 2, the Debug Port controller must check for software requested debug transactions at least every 125 microseconds. 2. If the debug port is enabled by the debug driver, and the standard host controller driver resets the USB port, USB debug transactions are held off for the duration of the reset and until after the first SOF is sent. 3. If the standard host controller driver suspends the USB port, then USB debug transactions are held off for the duration of the suspend/resume sequence and until after the first SOF is sent. 4. The ENABLED_CNT bit in the debug register space is independent of the similar port control bit in the associated Port Status and Control register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 225 Functional Description Table 5-47 shows the debug port behavior related to the state of bits in the debug registers as well as bits in the associated Port Status and Control register. Table 5-47. Debug Port Behavior OWNER_CN T ENABLED_C T Port Enable Run / Stop Suspen d 0 X X X X Debug port is not being used. Normal operation. 1 0 X X X Debug port is not being used. Normal operation. 1 1 0 0 X Debug port in Mode 1. SYNC keepalives sent plus debug traffic X Debug port in Mode 2. SOF (and only SOF) is sent as keepalive. Debug traffic is also sent. Note that no other normal traffic is sent out this port, because the port is not enabled. 1 1 0 1 Debug Port Behavior 1 1 1 0 0 Invalid. Host controller driver should never put controller into this state (enabled, not running and not suspended). 1 1 1 0 1 Port is suspended. No debug traffic sent. 1 1 1 1 0 Debug port in Mode 2. Debug traffic is interspersed with normal traffic. 1 1 1 1 1 Port is suspended. No debug traffic sent. 5.19.10.1.1 OUT Transactions An Out transaction sends data to the debug device. It can occur only when the following are true: • The debug port is enabled • The debug software sets the GO_CNT bit • The WRITE_READ#_CNT bit is set The sequence of the transaction is: 1. Software sets the appropriate values in the following bits: — USB_ADDRESS_CNF — USB_ENDPOINT_CNF — DATA_BUFFER[63:0] — TOKEN_PID_CNT[7:0] — SEND_PID_CNT[15:8] — DATA_LEN_CNT — WRITE_READ#_CNT: (note: this will always be 1 for OUT transactions) — GO_CNT: (note: this will always be 1 to initiate the transaction) 226 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 2. The debug port controller sends a token packet consisting of: — SYNC — TOKEN_PID_CNT field — USB_ADDRESS_CNT field — USB_ENDPOINT_CNT field — 5-bit CRC field 3. After sending the token packet, the debug port controller sends a data packet consisting of: — SYNC — SEND_PID_CNT field — The number of data bytes indicated in DATA_LEN_CNT from the DATA_BUFFER — 16-bit CRC NOTE: A DATA_LEN_CNT value of 0 is valid in which case no data bytes would be included in the packet. 4. After sending the data packet, the controller waits for a handshake response from the debug device. • If a handshake is received, the debug port controller: — a. Places the received PID in the RECEIVED_PID_STS field — b. Resets the ERROR_GOOD#_STS bit — c. Sets the DONE_STS bit • If no handshake PID is received, the debug port controller: — a. Sets the EXCEPTION_STS field to 001b — b. Sets the ERROR_GOOD#_STS bit — c. Sets the DONE_STS bit 5.19.10.1.2 IN Transactions An IN transaction receives data from the debug device. It can occur only when the following are true: • The debug port is enabled • The debug software sets the GO_CNT bit • The WRITE_READ#_CNT bit is reset The sequence of the transaction is: 1. Software sets the appropriate values in the following bits: — USB_ADDRESS_CNF — USB_ENDPOINT_CNF — TOKEN_PID_CNT[7:0] — DATA_LEN_CNT — WRITE_READ#_CNT: (note: this will always be 0 for IN transactions) — GO_CNT: (note: this will always be 1 to initiate the transaction) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 227 Functional Description 2. The debug port controller sends a token packet consisting of: — SYNC — TOKEN_PID_CNT field — USB_ADDRESS_CNT field — USB_ENDPOINT_CNT field — 5-bit CRC field. 3. After sending the token packet, the debug port controller waits for a response from the debug device. If a response is received: — The received PID is placed into the RECEIVED_PID_STS field — Any subsequent bytes are placed into the DATA_BUFFER — The DATA_LEN_CNT field is updated to show the number of bytes that were received after the PID. 4. If a valid packet was received from the device that was one byte in length (indicating it was a handshake packet), then the debug port controller: — Resets the ERROR_GOOD#_STS bit — Sets the DONE_STS bit 5. If a valid packet was received from the device that was more than one byte in length (indicating it was a data packet), then the debug port controller: — Transmits an ACK handshake packet — Resets the ERROR_GOOD#_STS bit — Sets the DONE_STS bit 6. If no valid packet is received, then the debug port controller: — Sets the EXCEPTION_STS field to 001b — Sets the ERROR_GOOD#_STS bit — Sets the DONE_STS bit. 5.19.10.1.3 Debug Software Enabling the Debug Port There are two mutually exclusive conditions that debug software must address as part of its startup processing: • The EHCI has been initialized by system software • The EHCI has not been initialized by system software Debug software can determine the current ‘initialized’ state of the EHCI by examining the Configure Flag in the EHCI USB 2.0 Command Register. If this flag is set, then system software has initialized the EHCI. Otherwise the EHCI should not be considered initialized. Debug software will initialize the debug port registers depending on the state of the EHCI. However, before this can be accomplished, debug software must determine which root USB port is designated as the debug port. Determining the Debug Port Debug software can easily determine which USB root port has been designated as the debug port by examining bits 20:23 of the EHCI Host Controller Structural Parameters register. This 4-bit field represents the numeric value assigned to the debug port (i.e., 0000=port 0). 228 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Debug Software Startup with Non-Initialized EHCI Debug software can attempt to use the debug port if after setting the OWNER_CNT bit, the Current Connect Status bit in the appropriate (See Determining the Debug Port) PORTSC register is set. If the Current Connect Status bit is not set, then debug software may choose to terminate or it may choose to wait until a device is connected. If a device is connected to the port, then debug software must reset/enable the port. Debug software does this by setting and then clearing the Port Reset bit the PORTSC register. To ensure a successful reset, debug software should wait at least 50 ms before clearing the Port Reset bit. Due to possible delays, this bit may not change to 0 immediately; reset is complete when this bit reads as 0. Software must not continue until this bit reads 0. If a high-speed device is attached, the EHCI will automatically set the Port Enabled/ Disabled bit in the PORTSC register and the debug software can proceed. Debug software should set the ENABLED_CNT bit in the Debug Port Control/Status register, and then reset (clear) the Port Enabled/Disabled bit in the PORTSC register (so that the system host controller driver does not see an enabled port when it is first loaded). Debug Software Startup with Initialized EHCI Debug software can attempt to use the debug port if the Current Connect Status bit in the appropriate (See Determining the Debug Port) PORTSC register is set. If the Current Connect Status bit is not set, then debug software may choose to terminate or it may choose to wait until a device is connected. If a device is connected, then debug software must set the OWNER_CNT bit and then the ENABLED_CNT bit in the Debug Port Control/Status register. Determining Debug Peripheral Presence After enabling the debug port functionality, debug software can determine if a debug peripheral is attached by attempting to send data to the debug peripheral. If all attempts result in an error (Exception bits in the Debug Port Control/Status register indicates a Transaction Error), then the attached device is not a debug peripheral. If the debug port peripheral is not present, then debug software may choose to terminate or it may choose to wait until a debug peripheral is connected. 5.19.11 USB Pre-Fetch Based Pause The Pre-Fetch Based Pause is a power management feature in USB (EHCI) host controllers to ensure maximum C3/C4 processor power state time with C2 popup. This feature applies to the period schedule, and works by allowing the DMA engine to identify periods of idleness and preventing the DMA engine from accessing memory when the periodic schedule is idle. Typically in the presence of periodic devices with multiple millisecond poll periods, the periodic schedule will be idle for several frames between polls. The USB Pre-Fetch Based Pause feature is disabled by setting bit 4 of EHCI Configuration Register Section 17.1.30. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 229 Functional Description 5.19.12 Function Level Reset Support (FLR) The USB EHCI Controllers support the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel® Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a PCI reset was asserted. 5.19.12.1 FLR Steps 5.19.12.1.1 FLR Initialization 1. A FLR is initiated by software writing a ‘1’ to the Initiate FLR bit. 2. All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.19.12.1.2 FLR Operation The Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 5.19.12.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: From the time Initiate FLR bit is written to 1, software must wait at least 100 ms before accessing the function. 5.20 SMBus Controller (D31:F3) The ICH9 provides an System Management Bus (SMBus) 2.0 host controller as well as an SMBus Slave Interface. The host controller provides a mechanism for the processor to initiate communications with SMBus peripherals (slaves). The ICH9 is also capable of operating in a mode in which it can communicate with I2C compatible devices. The ICH9 can perform SMBus messages with either packet error checking (PEC) enabled or disabled. The actual PEC calculation and checking is performed in hardware by the ICH9. The Slave Interface allows an external master to read from or write to the ICH9. Write cycles can be used to cause certain events or pass messages, and the read cycles can be used to determine the state of various status bits. The ICH9’s internal host controller cannot access the ICH9’s internal Slave Interface. The ICH9 SMBus logic exists in Device 31:Function 3 configuration space, and consists of a transmit data path, and host controller. The transmit data path provides the data flow logic needed to implement the seven different SMBus command protocols and is controlled by the host controller. The ICH9 SMBus controller logic is clocked by RTC clock. The SMBus Address Resolution Protocol (ARP) is supported by using the existing host controller commands through software, except for the new Host Notify command (which is actually a received message). 230 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description The programming model of the host controller is combined into two portions: a PCI configuration portion, and a system I/O mapped portion. All static configuration, such as the I/O base address, is done via the PCI configuration space. Real-time programming of the Host interface is done in system I/O space. The ICH9 SMBus host controller checks for parity errors as a target. If an error is detected, the detected parity error bit in the PCI Status Register (Device 31:Function 3:Offset 06h:bit 15) is set. If bit 6 and bit 8 of the PCI Command Register (Device 31:Function 3:Offset 04h) are set, an SERR# is generated and the signaled SERR# bit in the PCI Status Register (bit 14) is set. Note: The ICH9 SMBus Controller may stop responding if an SMBus device suddenly stops transmitting in the middle of a packet. This could result in unexpected system behavior, including a system hang. 5.20.1 Host Controller The SMBus host controller is used to send commands to other SMBus slave devices. Software sets up the host controller with an address, command, and, for writes, data and optional PEC; and then tells the controller to start. When the controller has finished transmitting data on writes, or receiving data on reads, it generates an SMI# or interrupt, if enabled. The host controller supports 8 command protocols of the SMBus interface (see System Management Bus (SMBus) Specification, Version 2.0): Quick Command, Send Byte, Receive Byte, Write Byte/Word, Read Byte/Word, Process Call, Block Read/Write, Block Write–Block Read Process Call, and Host Notify. The SMBus host controller requires that the various data and command fields be setup for the type of command to be sent. When software sets the START bit, the SMBus Host controller performs the requested transaction, and interrupts the processor (or generates an SMI#) when the transaction is completed. Once a START command has been issued, the values of the “active registers” (Host Control, Host Command, Transmit Slave Address, Data 0, Data 1) should not be changed or read until the interrupt status bit (INTR) has been set (indicating the completion of the command). Any register values needed for computation purposes should be saved prior to issuing of a new command, as the SMBus host controller updates all registers while completing the new command. The ICH9 supports the System Management Bus (SMBus) Specification, Version 2.0. Slave functionality, including the Host Notify protocol, is available on the SMBus pins. The SMLink and SMBus signals can be tied together externally depending on the TCO mode used. Refer to Section 5.14.2 for more details. Using the SMB host controller to send commands to the ICH9’s SMB slave port is not supported. 5.20.1.1 Command Protocols In all of the following commands, the Host Status Register (offset 00h) is used to determine the progress of the command. While the command is in operation, the HOST_BUSY bit is set. If the command completes successfully, the INTR bit will be set in the Host Status Register. If the device does not respond with an acknowledge, and the transaction times out, the DEV_ERR bit is set. If software sets the KILL bit in the Host Control Register while the command is running, the transaction will stop and the FAILED bit will be set. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 231 Functional Description Quick Command When programmed for a Quick Command, the Transmit Slave Address Register is sent. The PEC byte is never appended to the Quick Protocol. Software should force the PEC_EN bit to 0 when performing the Quick Command. Software must force the I2C_EN bit to 0 when running this command. See section 5.5.1 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Send Byte / Receive Byte For the Send Byte command, the Transmit Slave Address and Device Command Registers are sent For the Receive Byte command, the Transmit Slave Address Register is sent. The data received is stored in the DATA0 register. Software must force the I2C_EN bit to 0 when running this command. The Receive Byte is similar to a Send Byte, the only difference is the direction of data transfer. See sections 5.5.2 and 5.5.3 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Write Byte/Word The first byte of a Write Byte/Word access is the command code. The next 1 or 2 bytes are the data to be written. When programmed for a Write Byte/Word command, the Transmit Slave Address, Device Command, and Data0 Registers are sent. In addition, the Data1 Register is sent on a Write Word command. Software must force the I2C_EN bit to 0 when running this command. See section 5.5.4 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Read Byte/Word Reading data is slightly more complicated than writing data. First the ICH9 must write a command to the slave device. Then it must follow that command with a repeated start condition to denote a read from that device's address. The slave then returns 1 or 2 bytes of data. Software must force the I2C_EN bit to 0 when running this command. When programmed for the read byte/word command, the Transmit Slave Address and Device Command Registers are sent. Data is received into the DATA0 on the read byte, and the DAT0 and DATA1 registers on the read word. See section 5.5.5 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Process Call The process call is so named because a command sends data and waits for the slave to return a value dependent on that data. The protocol is simply a Write Word followed by a Read Word, but without a second command or stop condition. When programmed for the Process Call command, the ICH9 transmits the Transmit Slave Address, Host Command, DATA0 and DATA1 registers. Data received from the device is stored in the DATA0 and DATA1 registers. The Process Call command with I2C_EN set and the PEC_EN bit set produces undefined results. Software must force either I2C_EN or PEC_EN to 0 when running this command. See section 5.5.6 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Note: 232 For process call command, the value written into bit 0 of the Transmit Slave Address Register (SMB I/O register, offset 04h) needs to be 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Note: If the I2C_EN bit is set, the protocol sequence changes slightly: the Command Code (bits 18:11 in the bit sequence) are not sent - as a result, the slave will not acknowledge (bit 19 in the sequence). Block Read/Write The ICH9 contains a 32-byte buffer for read and write data which can be enabled by setting bit 1 of the Auxiliary Control register at offset 0Dh in I/O space, as opposed to a single byte of buffering. This 32-byte buffer is filled with write data before transmission, and filled with read data on reception. In the ICH9, the interrupt is generated only after a transmission or reception of 32 bytes, or when the entire byte count has been transmitted/received. The byte count field is transmitted but ignored by the ICH9 as software will end the transfer after all bytes it cares about have been sent or received. For a Block Write, software must either force the I2C_EN bit or both the PEC_EN and AAC bits to 0 when running this command. The block write begins with a slave address and a write condition. After the command code the ICH9 issues a byte count describing how many more bytes will follow in the message. If a slave had 20 bytes to send, the first byte would be the number 20 (14h), followed by 20 bytes of data. The byte count may not be 0. A Block Read or Write is allowed to transfer a maximum of 32 data bytes. When programmed for a block write command, the Transmit Slave Address, Device Command, and Data0 (count) registers are sent. Data is then sent from the Block Data Byte register; the total data sent being the value stored in the Data0 Register. On block read commands, the first byte received is stored in the Data0 register, and the remaining bytes are stored in the Block Data Byte register. See section 5.5.7 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Note: For Block Write, if the I2C_EN bit is set, the format of the command changes slightly. The ICH9 will still send the number of bytes (on writes) or receive the number of bytes (on reads) indicated in the DATA0 register. However, it will not send the contents of the DATA0 register as part of the message. Also, the Block Write protocol sequence changes slightly: the Byte Count (bits 27:20 in the bit sequence) are not sent - as a result, the slave will not acknowledge (bit 28 in the sequence). I2C Read This command allows the ICH9 to perform block reads to certain I2C devices, such as serial E2PROMs. The SMBus Block Read supports the 7-bit addressing mode only. However, this does not allow access to devices using the I2C “Combined Format” that has data bytes after the address. Typically these data bytes correspond to an offset (address) within the serial memory chips. Note: This command is supported independent of the setting of the I2C_EN bit. The I2C Read command with the PEC_EN bit set produces undefined results. Software must force both the PEC_EN and AAC bit to 0 when running this command. For I2C Read command, the value written into bit 0 of the Transmit Slave Address Register (SMB I/O register, offset 04h) needs to be 0. The format that is used for the command is shown in Table 5-48. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 233 Functional Description Table 5-48. I2C Block Read Bit 1 8:2 9 10 18:11 Description Start Slave Address — 7 bits Write Acknowledge from slave Send DATA1 register 19 Acknowledge from slave 20 Repeated Start 27:21 Slave Address — 7 bits 28 Read 29 Acknowledge from slave 37:30 38 46:39 47 Data byte 1 from slave — 8 bits Acknowledge Data byte 2 from slave — 8 bits Acknowledge – Data bytes from slave / Acknowledge – Data byte N from slave — 8 bits – NOT Acknowledge – Stop The ICH9 will continue reading data from the peripheral until the NAK is received. Block Write–Block Read Process Call The block write-block read process call is a two-part message. The call begins with a slave address and a write condition. After the command code the host issues a write byte count (M) that describes how many more bytes will be written in the first part of the message. If a master has 6 bytes to send, the byte count field will have the value 6 (0000 0110b), followed by the 6 bytes of data. The write byte count (M) cannot be 0. The second part of the message is a block of read data beginning with a repeated start condition followed by the slave address and a Read bit. The next byte is the read byte count (N), which may differ from the write byte count (M). The read byte count (N) cannot be 0. The combined data payload must not exceed 32 bytes. The byte length restrictions of this process call are summarized as follows: • M ≥ 1 byte • N ≥ 1 byte • M + N ≤ 32 bytes The read byte count does not include the PEC byte. The PEC is computed on the total message beginning with the first slave address and using the normal PEC computational rules. It is highly recommended that a PEC byte be used with the Block Write-Block Read Process Call. Software must do a read to the command register (offset 2h) to reset the 32 byte buffer pointer prior to reading the block data register. 234 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Note that there is no STOP condition before the repeated START condition, and that a NACK signifies the end of the read transfer. Note: E32B bit in the Auxiliary Control register must be set when using this protocol. See section 5.5.8 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. 5.20.2 Bus Arbitration Several masters may attempt to get on the bus at the same time by driving the SMBDATA line low to signal a start condition. The ICH9 continuously monitors the SMBDATA line. When the ICH9 is attempting to drive the bus to a 1 by letting go of the SMBDATA line, and it samples SMBDATA low, then some other master is driving the bus and the ICH9 will stop transferring data. If the ICH9 sees that it has lost arbitration, the condition is called a collision. The ICH9 will set the BUS_ERR bit in the Host Status Register, and if enabled, generate an interrupt or SMI#. The processor is responsible for restarting the transaction. When the ICH9 is a SMBus master, it drives the clock. When the ICH9 is sending address or command as an SMBus master, or data bytes as a master on writes, it drives data relative to the clock it is also driving. It will not start toggling the clock until the start or stop condition meets proper setup and hold time. The ICH9 will also ensure minimum time between SMBus transactions as a master. Note: The ICH9 supports the same arbitration protocol for both the SMBus and the System Management (SMLINK) interfaces. 5.20.3 Bus Timing 5.20.3.1 Clock Stretching Some devices may not be able to handle their clock toggling at the rate that the ICH9 as an SMBus master would like. They have the capability of stretching the low time of the clock. When the ICH9 attempts to release the clock (allowing the clock to go high), the clock will remain low for an extended period of time. The ICH9 monitors the SMBus clock line after it releases the bus to determine whether to enable the counter for the high time of the clock. While the bus is still low, the high time counter must not be enabled. Similarly, the low period of the clock can be stretched by an SMBus master if it is not ready to send or receive data. 5.20.3.2 Bus Time Out (Intel® ICH9 as SMBus Master) If there is an error in the transaction, such that an SMBus device does not signal an acknowledge, or holds the clock lower than the allowed time-out time, the transaction will time out. The ICH9 will discard the cycle and set the DEV_ERR bit. The time out minimum is 25 ms (800 RTC clocks). The time-out counter inside the ICH9 will start after the last bit of data is transferred by the ICH9 and it is waiting for a response. The 25 ms timeout counter will not count under the following conditions: 1. BYTE_DONE_STATUS bit (SMBus I/O Offset 00h, bit 7) is set 2. The SECOND_TO_STS bit (TCO I/O Offset 06h, bit 1) is not set (this indicates that the system has not locked up). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 235 Functional Description 5.20.4 Interrupts / SMI# The ICH9 SMBus controller uses PIRQB# as its interrupt pin. However, the system can alternatively be set up to generate SMI# instead of an interrupt, by setting the SMBUS_SMI_EN bit (Device 31:Function 0:Offset 40h:bit 1). Table 5-50 and Table 5-51 specify how the various enable bits in the SMBus function control the generation of the interrupt, Host and Slave SMI, and Wake internal signals. The rows in the tables are additive, which means that if more than one row is true for a particular scenario then the Results for all of the activated rows will occur. Table 5-49. Enable for SMBALERT# Event INTREN (Host Control I/O Register, Offset 02h, Bit 0) SMB_SMI_EN (Host Configuration Register, D31:F3:Offset 40h, Bit 1) SMBALERT_DIS (Slave Command I/O Register, Offset 11h, Bit 2) X X X Wake generated X 1 0 Slave SMI# generated (SMBUS_SMI_STS) 1 0 0 Interrupt generated SMBALERT# asserted low (always reported in Host Status Register, Bit 5) Result Table 5-50. Enables for SMBus Slave Write and SMBus Host Events Event SMB_SMI_EN (Host Configuration Register, D31:F3:Offset 40h, Bit1) Event Slave Write to Wake/SMI# Command X X Wake generated when asleep. Slave SMI# generated when awake (SMBUS_SMI_STS). Slave Write to SMLINK_SLAVE_S MI Command X X Slave SMI# generated when in the S0 state (SMBUS_SMI_STS) 0 X None 1 0 Interrupt generated 1 1 Host SMI# generated Any combination of Host Status Register [4:1] asserted 236 INTREN (Host Control I/O Register, Offset 02h, Bit 0) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-51. Enables for the Host Notify Command 5.20.5 HOST_NOTIFY_INTRE N (Slave Control I/O Register, Offset 11h, bit 0) SMB_SMI_EN (Host Config Register, D31:F3:Off40h, Bit 1) HOST_NOTIFY_WKEN (Slave Control I/O Register, Offset 11h, bit 1) 0 X 0 None X X 1 Wake generated 1 0 X Interrupt generated 1 1 X Slave SMI# generated (SMBUS_SMI_STS) Result SMBALERT# SMBALERT# is multiplexed with GPIO[11]. When enable and the signal is asserted, The ICH9 can generate an interrupt, an SMI#, or a wake event from S1–S5. 5.20.6 SMBus CRC Generation and Checking If the AAC bit is set in the Auxiliary Control register, the ICH9 automatically calculates and drives CRC at the end of the transmitted packet for write cycles, and will check the CRC for read cycles. It will not transmit the contents of the PEC register for CRC. The PEC bit must not be set in the Host Control register if this bit is set, or unspecified behavior will result. If the read cycle results in a CRC error, the DEV_ERR bit and the CRCE bit in the Auxiliary Status register at offset 0Ch will be set. 5.20.7 SMBus Slave Interface The ICH9’s SMBus Slave interface is accessed via the SMBus. The SMBus slave logic will not generate or handle receiving the PEC byte and will only act as a Legacy Alerting Protocol device. The slave interface allows the ICH9 to decode cycles, and allows an external microcontroller to perform specific actions. Key features and capabilities include: • Supports decode of three types of messages: Byte Write, Byte Read, and Host Notify. • Receive Slave Address register: This is the address that the ICH9 decodes. A default value is provided so that the slave interface can be used without the processor having to program this register. • Receive Slave Data register in the SMBus I/O space that includes the data written by the external microcontroller. • Registers that the external microcontroller can read to get the state of the ICH9. • Status bits to indicate that the SMBus slave logic caused an interrupt or SMI# due to the reception of a message that matched the slave address. — Bit 0 of the Slave Status Register for the Host Notify command — Bit 16 of the SMI Status Register (Section 13.8.3.15) for all others Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 237 Functional Description Note: The external microcontroller should not attempt to access the Intel ICH9’s SMBus slave logic until either: — 800 milliseconds after both: RTCRST# is high and RSMRST# is high, OR — The PLTRST# de-asserts If a master leaves the clock and data bits of the SMBus interface at 1 for 50 µs or more in the middle of a cycle, the ICH9 slave logic's behavior is undefined. This is interpreted as an unexpected idle and should be avoided when performing management activities to the slave logic. Note: When an external microcontroller accesses the SMBus Slave Interface over the SMBus a translation in the address is needed to accommodate the least significant bit used for read/write control. For example, if the ICH9 slave address (RCV_SLVA) is left at 44h (default), the external micro controller would use an address of 88h/89h (write/read). 5.20.7.1 Format of Slave Write Cycle The external master performs Byte Write commands to the ICH9 SMBus Slave I/F. The “Command” field (bits 11:18) indicate which register is being accessed. The Data field (bits 20:27) indicate the value that should be written to that register. Table 5-52 has the values associated with the registers. Table 5-52. Slave Write Registers Register 0 1–3 Function Command Register. See Table 5-53 below for valid values written to this register. Reserved 4 Data Message Byte 0 5 Data Message Byte 1 6–7 Reserved 8 Reserved 9–FFh Reserved NOTE: The external microcontroller is responsible to make sure that it does not update the contents of the data byte registers until they have been read by the system processor. The ICH9 overwrites the old value with any new value received. A race condition is possible where the new value is being written to the register just at the time it is being read. ICH9 will not attempt to cover this race condition (i.e., unpredictable results in this case). 238 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description . Table 5-53. Command Types Command Type Description 0 Reserved 1 WAKE/SMI#. This command wakes the system if it is not already awake. If system is already awake, an SMI# is generated. NOTE: The SMB_WAK_STS bit will be set by this command, even if the system is already awake. The SMI handler should then clear this bit. 2 Unconditional Powerdown. This command sets the PWRBTNOR_STS bit, and has the same effect as the Powerbutton Override occurring. 3 HARD RESET WITHOUT CYCLING: This command causes a hard reset of the system (does not include cycling of the power supply). This is equivalent to a write to the CF9h register with bits 2:1 set to 1, but bit 3 set to 0. 4 HARD RESET SYSTEM. This command causes a hard reset of the system (including cycling of the power supply). This is equivalent to a write to the CF9h register with bits 3:1 set to 1. 5 Disable the TCO Messages. This command will disable the Intel® ICH9 from sending Heartbeat and Event messages (as described in Section 5.14). Once this command has been executed, Heartbeat and Event message reporting can only be re-enabled by assertion and deassertion of the RSMRST# signal. 6 WD RELOAD: Reload watchdog timer. 7 Reserved 8 SMLINK_SLV_SMI. When ICH9 detects this command type while in the S0 state, it sets the SMLINK_SLV_SMI_STS bit (see Section 13.9.5). This command should only be used if the system is in an S0 state. If the message is received during S1– S5 states, the ICH9 acknowledges it, but the SMLINK_SLV_SMI_STS bit does not get set. NOTE: It is possible that the system transitions out of the S0 state at the same time that the SMLINK_SLV_SMI command is received. In this case, the SMLINK_SLV_SMI_STS bit may get set but not serviced before the system goes to sleep. Once the system returns to S0, the SMI associated with this bit would then be generated. Software must be able to handle this scenario. 9-FFh Reserved. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 239 Functional Description 5.20.7.2 Format of Read Command The external master performs Byte Read commands to the ICH9 SMBus Slave interface. The “Command” field (bits 18:11) indicate which register is being accessed. The Data field (bits 30:37) contain the value that should be read from that register. Table 5-54. Slave Read Cycle Format Bit 1 Description Driven by Comment Start External Microcontroller Slave Address - 7 bits External Microcontroller Must match value in Receive Slave Address register 9 Write External Microcontroller Always 0 10 ACK Intel ICH9 Command code – 8 bits External Microcontroller 19 ACK Intel ICH9 20 Repeated Start External Microcontroller Slave Address - 7 bits External Microcontroller Must match value in Receive Slave Address register 28 Read External Microcontroller Always 1 29 ACK Intel ICH9 30-37 Data Byte Intel ICH9 38 NOT ACK External Microcontroller 39 Stop External Microcontroller 2-8 11-18 21-27 Indicates which register is being accessed. See Table 5-55 below for list of implemented registers. Value depends on register being accessed. Table 5-55 below for list of implemented registers. Table 5-55. Data Values for Slave Read Registers (Sheet 1 of 3) Register Bits 0 7:0 1 2:0 Description Reserved for capabilities indication. Should always return 00h. Future chips may return another value to indicate different capabilities. System Power State 000 = S0 001 = S1 010 = Reserved 011 = S3 100 = S4 101 = S5 110 = Reserved 111 = Reserved 2 3 7:3 Reserved 3:0 Reserved 7:4 Reserved 5:0 Watchdog Timer current value Note that Watchdog Timer has 10 bits, but this field is only 6 bits. If the current value is greater than 3Fh, ICH9 will always report 3Fh in this field. 7:6 4 240 0 Reserved 1 = The Intruder Detect (INTRD_DET) bit is set. This indicates that the system cover has probably been opened. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-55. Data Values for Slave Read Registers (Sheet 2 of 3) Register Bits Description 1 1 = BTI Temperature Event occurred. This bit will be set if the Intel ICH9’s THRM# input signal is at a valid low voltage state. This bit will be clear if the THRM# input signal is at a valid high voltage state. NOTE: This bit interprets the behavior if the THRM# pin as active low. This bit is set independent of the TRM#_POL bit setting. 2 DOA CPU Status. This bit will be 1 to indicate that the processor is dead 3 1 = SECOND_TO_STS bit set. This bit will be set after the second timeout (SECOND_TO_STS bit) of the Watchdog Timer occurs. 6:4 7 Reserved. Will always be 0, but software should ignore. Reflects the value of the GPIO[11]/SMBALERT# pin (and is dependent upon the value of the GPI_INV[11] bit. If the GPI_INV[11] bit is 1, then the value in this bit equals the level of the GPI[11]/SMBALERT# pin (high = 1, low = 0). If the GPI_INV[11] bit is 0, then the value of this bit will equal the inverse of the level of the GPIO[11]/SMBALERT# pin (high = 0, low = 1). 5 0 FWH bad bit. This bit will be 1 to indicate that the FWH read returned FFh, which indicates that it is probably blank. 1 Battery Low Status. ‘1’ if the BATLOW# pin is a ‘0’.(Mobile Only) 2 CPU Power Failure Status: ‘1’ if the CPUPWR_FLR bit in the GEN_PMCON_2 register is set. 3 INIT# due to receiving Shutdown message: This event is visible from the reception of the shutdown message until a platform reset is done if the Shutdown Policy Select bit (SPS) is configured to drive INIT#. When the SPS bit is configured to generate PLTRST# based on shutdown, this register bit will always return 0. Events on signal will not create a event message 4 Reserved 5 POWER_OK_BAD: Indicates the failure core power well ramp during boot/resume. This bit will be active if the SLP_S3# pin is de-asserted and PWROK pin is not asserted. 6 Thermal Trip: This bit will shadow the state of processor Thermal Trip status bit (CTS) (16.2.1.2, GEN_PMCON_2, bit 3). Events on signal will not create a event message Reserved: Default value is “X” 7 Note: Software should not expect a consistent value when this bit is read through SMBUS/SMLINK 6 7:0 Contents of the Message 1 register. Refer to Section 13.9.8 for the description of this register. 7 7:0 Contents of the Message 2 register. Refer to Section 13.9.8 for the description of this register. 8 7:0 Contents of the TCO_WDCNT register. Refer to Section 13.9.9 for the description of this register. 9 7:0 Seconds of the RTC A 7:0 Minutes of the RTC B 7:0 Hours of the RTC C 7:0 “Day of Week” of the RTC Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 241 Functional Description Table 5-55. Data Values for Slave Read Registers (Sheet 3 of 3) 5.20.7.2.1 Register Bits Description D 7:0 “Day of Month” of the RTC E 7:0 Month of the RTC F 7:0 Year of the RTC 10h–FFh 7:0 Reserved Behavioral Notes According to SMBus protocol, Read and Write messages always begin with a Start bit – Address– Write bit sequence. When the ICH9 detects that the address matches the value in the Receive Slave Address register, it will assume that the protocol is always followed and ignore the Write bit (bit 9) and signal an Acknowledge during bit 10. In other words, if a Start –Address–Read occurs (which is invalid for SMBus Read or Write protocol), and the address matches the ICH9’s Slave Address, the ICH9 will still grab the cycle. Also according to SMBus protocol, a Read cycle contains a Repeated Start–Address– Read sequence beginning at bit 20. Once again, if the Address matches the ICH9’s Receive Slave Address, it will assume that the protocol is followed, ignore bit 28, and proceed with the Slave Read cycle. Note: An external microcontroller must not attempt to access the ICH9’s SMBus Slave logic until at least 1 second after both RTCRST# and RSMRST# are deasserted (high). 5.20.7.3 Slave Read of RTC Time Bytes The ICH9 SMBus slave interface allows external SMBus master to read the internal RTC’s time byte registers. The RTC time bytes are internally latched by the ICH9’s hardware whenever RTC time is not changing and SMBus is idle. This ensures that the time byte delivered to the slave read is always valid and it does not change when the read is still in progress on the bus. The RTC time will change whenever hardware update is in progress, or there is a software write to the RTC time bytes. The ICH9 SMBus slave interface only supports Byte Read operation. The external SMBus master will read the RTC time bytes one after another. It is software’s responsibility to check and manage the possible time rollover when subsequent time bytes are read. For example, assuming the RTC time is 11 hours: 59 minutes: 59 seconds. When the external SMBus master reads the hour as 11, then proceeds to read the minute, it is possible that the rollover happens between the reads and the minute is read as 0. This results in 11 hours: 0 minute instead of the correct time of 12 hours: 0 minutes. Unless it is certain that rollover will not occur, software is required to detect the possible time rollover by reading multiple times such that the read time bytes can be adjusted accordingly if needed. 242 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.20.7.4 Format of Host Notify Command The ICH9 tracks and responds to the standard Host Notify command as specified in the System Management Bus (SMBus) Specification, Version 2.0. The host address for this command is fixed to 0001000b. If the ICH9 already has data for a previously-received host notify command which has not been serviced yet by the host software (as indicated by the HOST_NOTIFY_STS bit), then it will NACK following the host address byte of the protocol. This allows the host to communicate non-acceptance to the master and retain the host notify address and data values for the previous cycle until host software completely services the interrupt. Note: Host software must always clear the HOST_NOTIFY_STS bit after completing any necessary reads of the address and data registers. Table 5-56 shows the Host Notify format. Table 5-56. Host Notify Format Bit 1 8:2 9 10 Description Start Driven By Comment External Master SMB Host Address — 7 bits External Master Always 0001_000 Write External Master Always 0 ACK (or NACK) Intel® ICH9 ICH9 NACKs if HOST_NOTIFY_STS is 1 Device Address – 7 bits External Master Indicates the address of the master; loaded into the Notify Device Address Register 18 Unused — Always 0 External Master 7-bit-only address; this bit is inserted to complete the byte 19 ACK ICH9 Data Byte Low — 8 bits External Master ACK ICH9 Data Byte High — 8 bits External Master 37 ACK ICH9 38 Stop External Master 17:11 27:20 28 36:29 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Loaded into the Notify Data Low Byte Register Loaded into the Notify Data High Byte Register 243 Functional Description 5.21 Intel® High Definition Audio Overview The ICH9’s High Definition Audio (HDA) controller communicates with the external codec(s) over the Intel High Definition Audio serial link. The controller consists of a set of DMA engines that are used to move samples of digitally encoded data between system memory and an external codec(s). The ICH9 implements four output DMA engines and 4 input DMA engines. The output DMA engines move digital data from system memory to a D-A converter in a codec. ICH9 implements a single Serial Data Output signal (HDA_SDOUT) that is connected to all external codecs. The input DMA engines move digital data from the A-D converter in the codec to system memory. The ICH9 implements four Serial Digital Input signals (HDA_SDI[3:0]) supporting up to four codecs. Audio software renders outbound and processes inbound data to/from buffers in system memory. The location of individual buffers is described by a Buffer Descriptor List (BDL) that is fetched and processed by the controller. The data in the buffers is arranged in a predefined format. The output DMA engines fetch the digital data from memory and reformat it based on the programmed sample rate, bit/sample and number of channels. The data from the output DMA engines is then combined and serially sent to the external codecs over the Intel High Definition Audio link. The input DMA engines receive data from the codecs over the Intel High Definition Audio link and format the data based on the programmable attributes for that stream. The data is then written to memory in the predefined format for software to process. Each DMA engine moves one stream of data. A single codec can accept or generate multiple streams of data, one for each A-D or D-A converter in the codec. Multiple codecs can accept the same output stream processed by a single DMA engine. Codec commands and responses are also transported to and from the codecs via DMA engines. 5.21.1 Intel® High Definition Audio Docking (Mobile Only) 5.21.1.1 Dock Sequence Note that this sequence is followed when the system is running and a docking event occurs. 1. Since the ICH9 supports docking, the Docking Supported (DCKSTS. DS) bit defaults to a 1. POST BIOS and ACPI BIOS software uses this bit to determine if the HD Audio controller supports docking. BIOS may write a 0 to this RWO bit during POST to effectively turn off the docking feature. 2. After reset in the undocked quiescent state, the Dock Attach (DCKCTL.DA) bit and the Dock Mate (DCKSTS.DM) bit are both de-asserted. The HDA_DOCK_EN# signal is de-asserted and HDA_DOCK_RST# is asserted. Bit Clock, SYNC and SDO signals may or may no be running at the point in time that the docking event occurs. 3. The physical docking event is signaled to ACPI BIOS software via ACPI control methods. This is normally done through a GPIO signal on the ICH9 and is outside the scope of this section of the spec. 4. ACPI BIOS software first checks that the docking is supported via DCKSTS.DS=1 and that the DCKSTS.DM=0 and then initiates the docking sequence by writing a 1 to the DCKCTL.DA bit. 5. The HD Audio controller then asserts the HDA_DOCK_EN# signal so that the Bit Clock signal begins toggling to the dock codec. HDA_DOCK_EN# shall be asserted synchronously to Bit Clock and timed such that Bit Clock is low, SYNC is low, and SDO is low. Pull-down resistors on these signals in the docking station discharge the signals low so that when the state of the signal on both sides of the switch is the same when the switch is turned on. This reduces the potential for charge 244 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description coupling glitches on these signals. Note that in the ICH9 the first 8 bits of the Command field are “reserved” and always driven to 0's. This creates a predictable point in time to always assert HDA_DOCK_EN#. Note that the HD Audio link reset exit specification that requires that SYNC and SDO be driven low during Bit Clock startup is not ensured. Note also that the SDO and Bit Clock signals may not be low while HDA_DOCK_RST# is asserted which also violates the spec. 6. After the controller asserts HDA_DOCK_EN# it waits for a minimum of 2400 Bit Clocks (100us) and then de-asserts HDA_DOCK_RST#. This is done in such a way to meet the HD Audio link reset exit specification. HDA_DOCK_RST# de-assertion should be synchronous to Bit Clock and timed such that there are least 4 full Bit ClockS from the de-assertion of HDA_DOCK_RST# to the first frame SYNC assertion. 7. The Connect/Turnaround/Address Frame hardware initialization sequence will now occur on the dock codecs' SDI signals. A dock codec is detected when SDI is high on the last Bit Clock cycle of the Frame Sync of a Connect Frame. The appropriate bit(s) in the State Change Status (STATESTS) register will be set. The Turnaround and Address Frame initialization sequence then occurs on the dock codecs' SDI(s). 8. After this hardware initialization sequence is complete (approximately 32 frames), the controller hardware sets the DCKSTS.DM bit to 1 indicating that the dock is now mated. ACPI BIOS polls the DCKSTS.DM bit and when it detects it is set to 1, conveys this to the OS through a plug-N-play IRP. This eventually invokes the HD Audio Bus Driver, which then begins it's codec discovery, enumeration, and configuration process. 9. Alternatively to step #8, the HD Audio Bus Driver may choose to enable an interrupt by setting the WAKEEN bits for SDINs that didn't originally have codecs attached to them. When a corresponding STATESTS bit gets set an interrupt will be generated. In this case the HD Audio Bus Driver is called directly by this interrupt instead of being notified by the plug-N-play IRP. 10. HD Audio Bus Driver software “discovers” the dock codecs by comparing the bits now set in the STATESTS register with the bits that were set prior to the docking event. 5.21.1.2 Exiting D3/CRST# when Docked 1. In D3/CRST#, CRST# is asserted by the HD Audio Bus Driver. CRST# asserted resets the dock state machines, but does not reset the DCKCTL.DA bit. Because the dock state machines are reset, the dock is electrically isolated (HDA_DOCK_EN# de-asserted) and DOCK_RST# is asserted. 2. The Bus Driver clears the STATESTS bits, then de-asserts CRST#, waits approximately 7ms, then checks the STATESTS bits to see which codecs are present. 3. When CRST# is de-asserted, the dock state machine detects that DCKCTL.DA is still set and the controller hardware sequences through steps to electrically connect the dock by asserting HDA_DOCK_EN# and then eventually de-asserts DOCK_RST#. This completes within the 7ms mentioned in step 2). 4. The Bus Driver enumerates the codecs present as indicated via the STATESTS bits. 5. Note that this process did not require BIOS or ACPI BIOS to set the DCKCTL.DA bit. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 245 Functional Description 5.21.1.3 Cold Boot/Resume from S3 When Docked 1. When booting and resuming from S3, PLTRST# switches from asserted to deasserted. This clears the DCKCTL.DA bit and the dock state machines. Because the dock state machines are reset, the dock is electrically isolated (HDA_DOCK_EN# de-asserted) and DOCK_RST# is asserted. 2. POST BIOS detects that the dock is attached and sets the DCKCTL.DA bit to 1. Note that at this point CRST# is still asserted so the dock state machine will remain in it's reset state. 3. The Bus Driver clears the STATESTS bits, then de-asserts CRST#, waits approximately 7ms, then checks the STATESTS bits to see which codecs are present. 4. When CRST# is de-asserted, the dock state machine detects that DCKCTL.DA is still set and the controller hardware sequences through steps to electrically connect the dock by asserting HDA_DOCK_EN# and then eventually de-asserts DOCK_RST#. This completes within the 7ms mentioned in step 3). 5. The Bus Driver enumerates the codecs present as indicated via the STATESTS bits. 5.21.1.4 Undock Sequence There are two possible undocking scenarios. The first is the one that is initiated by the user that invokes software and gracefully shuts down the dock codecs before they are undocked. The second is referred to as the “surprise undock” where the user undocks while the dock codec is running. Both of these situations appear the same to the controller as it is not cognizant of the “surprise removal”. But both sequences will be discussed here. 5.21.1.4.1 Normal Undock 1. In the docked quiescent state, the Dock Attach (DCKCTL.DA) bit and the Dock Mate (DCKSTS.DM) bit are both asserted. The HDA_DOCK_EN# signal is asserted and HDA_DOCK_RST# is de-asserted. 2. The user initiates an undock event through the GUI interface or by pushing a button. This mechanism is outside the scope of this section of the document. Either way ACPI BIOS software will be invoked to manage the undock process. 3. ACPI BIOS will call the HD Audio Bus Driver software in order to halt the stream to the dock codec(s) prior to electrical undocking. If the HD Audio Bus Driver is not capable of halting the stream to the docked codec, ACPI BIOS will initiate the hardware undocking sequence as described in the next step while the dock stream is still running. From this standpoint, the result is similar to the “surprise undock” scenario where an audio glitch may occur to the docked codec(s) during the undock process. 4. The ACPI BIOS initiates the hardware undocking sequence by writing a 0 to the DCKCTL.DA bit. 5. The HD Audio controller asserts HDA_DOCK_RST#. HDA_DOCK_RST# assertion shall be synchronous to Bit Clock. There are no other timing requirements for HDA_DOCK_RST# assertion. Note that the HD Audio link reset specification requirement that the last Frame sync be skipped will not be met. 6. A minimum of 4 Bit Clocks after HDA_DOCK_RST# the controller will de-assert HDA_DOCK_EN# to isolate the dock codec signals from the ICH9 HD Audio link signals. HDA_DOCK_EN# is de-asserted synchronously to Bit Clock and timed such that Bit Clock, SYNC, and SDO are low. 7. After this hardware undocking sequence is complete the controller hardware clears the DCKSTS.DM bit to 0 indicating that the dock is now un-mated. ACPI BIOS software polls DCKSTS.DM and when it sees DM set, conveys to the end user that physical undocking can proceed. The controller is now ready for a subsequent docking event. 246 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.21.1.4.2 Surprise Undock 1. In the surprise undock case the user undocks before software has had the opportunity to gracefully halt the stream to the dock codec and initiate the hardware undock sequence. 2. A signal on the docking connector is connected to the switch that isolates the dock codec signals from the ICH9 HD Audio link signals (DOCK_DET# in the conceptual diagram). When the undock event begins to occur the switch will be put into isolate mode. 3. The undock event is communicated to the ACPI BIOS via ACPI control methods that are outside the scope of this section of the document. 4. ACPI BIOS software writes a 0 to the DCKCTL.DA bit. ACPI BIOS then calls the HD Audio Bus Driver via plug-N-play IRP. The Bus Driver then posthumously cleans up the dock codec stream. 5. The HD Audio controller hardware is oblivious to the fact that a surprise undock occurred. The flow from this point on is identical to the normal undocking sequence described in section 0 starting at step 3). It finishes with the hardware clearing the DCKSTS.DM bit set to 0 indicating that the dock is now un-mated. The controller is now ready for a subsequent docking event. 5.21.1.5 Interaction Between Dock/Undock and Power Management States When exiting from S3, PLTRST# will be asserted. The POST BIOS is responsible for initiating the docking sequence if the dock is already attached when PLTRST# is deasserted. POST BIOS writes a 1 to the DCKCTL.DA bit prior to the HD Audio driver deasserting CRTS# and detecting and enumerating the codecs attached to the HDA_DOCK_RST# signal. The HD Audio controller does not directly monitor a hardware signal indicating that a dock is attached. Therefore a method outside the scope of this document must be used to cause the POST BIOS to initiate the docking sequence. When exiting from D3, CRST# will be asserted. When CRST# bit is “0” (asserted), the DCKCTL.DA bit is not cleared. The dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, HDA_DOCK_RST# will be asserted and the DCKSTS.DM bit will be cleared to reflect this state. When the CRST# bit is de-asserted, the dock state machine will detect that DCKCTL.DA is set to “1” and will begin sequencing through the dock process. Note that this does not require any software intervention. 5.21.1.6 Relationship between HDA_DOCK_RST# and HDA_RST# HDA_RST# will be asserted when a PLTRST# occurs or when the CRST# bit is 0. As long as HDA_RST# is asserted, the DOCK_RST# signal will also be asserted. When PLTRST# is asserted, the DCKCTL.DA and DCKSTS.DM bits will be get cleared to their default state (0's), and the dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, and HDA_DOCK_RST# will be asserted. After any PLTRST#, POST BIOS software is responsible for detecting that a dock is attached and then writing a “1” to the DCKCTL.DA bit prior to the HD Audio Bus Driver de-asserting CRST#. When CRST# bit is “0” (asserted), the DCKCTL.DA bit is not cleared. The dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, HDA_DOCK_RST# will be asserted and the DCKSTS.DM bit will be cleared to reflect this state. When the CRST# bit is de-asserted, the dock state machine will detect that DCKCTL.DA is set to “1” and will begin sequencing through the dock process. Note that this does not require any software intervention. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 247 Functional Description 5.21.2 Function Level Reset Support (FLR) The Intel® High Definition Audio Controller supports the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a PCI reset was asserted. 5.21.2.1 FLR Steps 5.21.2.1.1 FLR Initialization 1. A FLR is initiated by software writing a ‘1’ to the Initiate FLR bit. 2. All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.21.2.1.2 FLR Operation The Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 5.21.2.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: From the time Initiate FLR bit is written to 1, software must wait at least 100 ms before accessing the function. 5.22 Intel® Active Management Technology (Intel® AMT) (Digital Office Only) Intel Active Management Technology is a set of advanced manageability features developed as a direct result of IT customer feedback gained through Intel market research. Reducing the Total Cost of Ownership (TCO) through improved asset tracking, remote manageability, and fewer desk-side visits were identified as key IT priorities. Intel AMT extends the capabilities of existing management solutions by making the asset information, remote diagnostics, recovery and contain capabilities always available, or Out of Band (OOB), even when the system is in a low-power “off” state or the OS is hung. Another feature of Intel AMT is System Defense. System Defense is used to stop the propagation of worms and viruses. Programmable packet filters in the integrated LAN Controller are used to accomplish this. These filters inspect all incoming and all outgoing packets and decide whether to block or pass the packets as configured. There is no indication to the host that a packet has been blocked or accepted. The logic can be used to accept or block reception to host or transmission to network paths. Additionally, counter logic can be used to count the number or filter matches for a given filter. This feature allows for statistical sampling of connections as well as rate limiting of connections. 248 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.22.1 Intel® AMT Features • E-Asset Tag • OOB HW and SW Inventory Logs • OOB Alerts • IDE Redirect • Serial over LAN for Remote Control • Remote Diagnostics Execution • OS Lock-Up Alert • OS Repair • Remote BIOS Recovery and Update 5.22.2 Intel® AMT Requirements Intel AMT is a platform-level solution that utilizes multiple system components including: • Intel AMT-Ready ICH9 component • Intel Gigabit Ethernet PHY (Intel® 82566 Gigabit Platform LAN Connect device) with Intel Active Management Technology for remote access • SPI flash memory with 4KB or 8KB sector erase that meets requirements set in Section 5.23.4 (32 Mb minimum for Intel AMT) to store asset information, management software code, and logs • BIOS to provide asset detection and POST diagnostics (BIOS and Intel AMT can optionally share same flash memory device) • Familiar ISV software packages to take advantage of Intel AMT’s platform management capabilities 5.23 Serial Peripheral Interface (SPI) The Serial Peripheral Interface (SPI) is a 4-pin interface that provides a potentially lower-cost alternative for system flash versus the Firmware Hub on the LPC bus. The 4-pin SPI interface consists of clock (CLK), master data out (Master Out Slave In (MOSI)), master data in (Master In Slave Out (MISO)) and an active low chip select (SPI_CS[1:0]#). The ICH9 supports up to two SPI flash devices using two separate Chip Select pins. Each SPI flash device can be up to 16 MBytes. The ICH9 SPI interface supports 20 MHz and 33 MHz SPI devices. Communication on the SPI bus is done with a Master – Slave protocol. The Slave is connected to the ICH9 and is implemented as a tri-state bus. Note: When SPI is selected by the Boot BIOS Destination Strap and a SPI device is detected by the ICH9, LPC based BIOS flash is disabled. 5.23.1 SPI Supported Feature Overview SPI Flash on the ICH9 has two operational modes, descriptor and non-descriptor. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 249 Functional Description 5.23.1.1 Non-Descriptor Mode Non-descriptor mode is similar to the flash functionality of ICH7. In this mode, SPI Flash can only be used for BIOS. Direct read and writes are not supported. BIOS has read/write access only through register accesses. Through those register accesses BIOS can read and write to the entire flash without security checking. There is also no support for the integrated Gigabit Ethernet, Management Engine, as well multiple SPI Flash components. 5.23.1.2 Descriptor Mode Descriptor Mode enables many new features of the chipset: • Integrated Gigabit Ethernet and Host processor for Gigabit Ethernet Software • Intel® Active Management Technology (Digital Office Only) • Intel® Quiet System Technology • Supports two SPI Flash components using two separate chip select pins • Hardware enforced security restricting master accesses to different regions • Chipset Soft Strap region provides the ability to use Flash NVM as an alternative to hardware pull-up/pull-down resistors for both ICH and MCH • Supports the SPI Fast Read instruction and frequencies of 33 MHz • Uses standardized Flash Instruction Set 5.23.1.2.1 SPI Flash Regions In Descriptor Mode the Flash is divided into five separate regions: Region Content 0 Flash Descriptor 1 BIOS 2 Management Engine 3 Gigabit Ethernet 4 Platform Data Only three masters can access the four regions: Host processor running BIOS code, Integrated Gigabit Ethernet and Host processor running Gigabit Ethernet Software, and Management Engine. The only required region is Region 0, the Flash Descriptor. Region 0 must be located in the first sector of device 0 (offset 0). Flash Region Sizes SPI flash space requirements differ by platform and configuration. The Flash Descriptor requires one 4 KB or larger block. GbE requires two 4 KB or larger blocks. The Platform Data Region is 32 KB. The amount of flash space consumed is dependent on the erase granularity of the flash part and the platform requirements for the ME and BIOS regions. The ME region will contain firmware to support Intel® Advanced Fan Speed Control, Intel® Active Management Technology (Digital Office only), ASF 2.0 and integrated Trusted Platform Module (mobile only). 250 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description Table 5-57. Region Size versus Erase Granularity of Flash Components 5.23.1.3 Region Size with 4 KB Blocks Size with 8 KB Blocks (Mobile Only) Size with 64 KB Blocks Descriptor 4 KB 8 KB 64 KB GbE 8 KB 16 KB 128 KB Platform Data Region 32 KB 32 KB Not Supported BIOS Varies by Platform Varies by Platform Varies by Platform ME Varies by Platform Varies by Platform Varies by Platform Device Partitioning The ICH9 SPI Flash controller supports two sets of attributes in SPI flash space. This allows for supporting an asymmetric flash component that has two separate sets of attributes in the upper and lower part of the memory array. An example of this is a flash part that has different erase granularities in two different parts of the memory array. This allows for the usage of two separate flash vendors if using two different flash parts. Figure 5-16. Flash Partition Boundary UpperFlash Partition … FlashPartition Boundary Lower Flash Partition 5.23.2 … Flash Descriptor The maximum size of the Flash Descriptor is 4 KB. If the block/sector size of the SPI flash device is greater than 4 KB, the flash descriptor will only use the first 4 KB of the first block. The flash descriptor requires its own block at the bottom of memory (0x00h). The information stored in the Flash Descriptor can only be written during the manufacturing process as its read/write permissions must be set to Read only when the computer leaves the manufacturing floor. The Flash Descriptor is made up of eleven sections: Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 251 Functional Description Figure 5-17. Flash Descriptor Sections 4KB OEM Section Descriptor Upper MAP Management Engine VSCC Table Reserved MCH Soft Straps ICH Soft Straps Master Region Component Descriptor MAP Signature 0 1. The Flash signature selects Descriptor Mode as well as verifies if the flash is programmed and functioning. The data at the bottom of the flash (offset 0) must be 0FF0A55Ah in order to be in Descriptor mode. 2. The Descriptor map has pointers to the other five descriptor sections as well as the size of each. 252 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 3. The component section has information about the SPI flash in the system including: the number of components, density of each, invalid instructions (such as chip erase), and frequencies for read, fast read and write/erase instructions. 4. The Region section points to the three other regions as well as the size of each region. 5. The master region contains the security settings for the flash, granting read/write permissions for each region and identifying each master by a requestor ID. See Section 5.23.2.1 for more information. 6 & 7. The MCH and ICH chipset soft strap sections contain MCH and ICH configurable parameters. 8. The Reserved region between the top of the MCH strap section and the bottom of the OEM Section is reserved for future chipset usages. 9 . The Descriptor Upper MAP determines the length and base address of the Management Engine VSCC Table. 10. The Management Engine VSCC Table holds the JEDEC ID and the VSCC information of the entire SPI Flash supported by the NVM image. 11. OEM Section is 256 Bytes reserved at the top of the Flash Descriptor for use by OEM. 5.23.2.1 Descriptor Master Region The master region defines read and write access setting for each region of the SPI device. The master region recognizes three masters: BIOS, Gigabit Ethernet, and Management Engine. Each master is only allowed to do direct reads of its primary regions. Table 5-58. Region Access Control Table Master Read/Write Access Region CPU and BIOS ME/MCH GbE Controller Descriptor N/A N/A N/A BIOS CPU and BIOS can always read from and write to BIOS Region Read / Write Read / Write Management Engine Read / Write ME can always read from and write to ME Region Read / Write Gigabit Ethernet Read / Write Read / Write GbE software can always read from and write to GbE region Platform Data Region N/A N/A N/A Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 253 Functional Description 5.23.3 Flash Access There are two types of flash accesses: Direct Access: • Masters are allowed to do direct read only of their primary region — Gigabit Ethernet region can only be directly accessed by the Gigabit Ethernet controller. Gigabit Ethernet software must use Program Registers to access the Gigabit Ethernet region. • Master's Host or Management Engine virtual read address is converted into the SPI Flash Linear Address (FLA) using the Flash Descriptor Region Base/Limit registers Program Register Access: • Program Register Accesses are not allowed to cross a 4KB boundary and can not issue a command that might extend across two components • Software programs the FLA corresponding to the region desired — Software must read the devices Primary Region Base/Limit address to create a FLA. 5.23.3.1 Direct Access Security • Requester ID of the device must match that of the primary Requester ID in the Master Section • Calculated Flash Linear Address must fall between primary region base/limit • Direct Write not allowed • Direct Read Cache contents are reset to 0's on a read from a different master — Supports the same cache flush mechanism in ICH7 which includes Program Register Writes 5.23.3.2 Register Access Security • Only primary region masters can access the registers Note: Processor running Gigabit Ethernet software can access Gigabit Ethernet registers • Masters are only allowed to read or write those regions they have read/write permission • Using the Flash Region Access Permissions, one master can give another master read/write permissions to their area • Using the five Protected Range registers, each master can add separate read/write protection above that granted in the Flash Descriptor for their own accesses — Example: BIOS may want to protect different regions of BIOS from being erased — Ranges can extend across region boundaries 5.23.4 Serial Flash Device Compatibility Requirements A variety of serial flash devices exist in the market. For a serial flash device to be compatible with the Intel ICH9 SPI bus, it must meet the minimum requirements detailed in the following sections. 254 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.23.4.1 Intel® ICH9 SPI Based BIOS Requirements A serial flash device must meet the following minimum requirements when used explicitly for system BIOS storage. • Erase size capability of at least one of the following: 64 Kbytes, 8 Kbytes, 4 Kbytes, or 256 bytes. • Device must support multiple writes to a page without requiring a preceding erase cycle (Refer to Section 5.23.5) • Serial flash device must ignore the upper address bits such that an address of FFFFFFh aliases to the top of the flash memory. • SPI Compatible Mode 0 support (clock phase is 0 and data is latched on the rising edge of the clock). • If the device receives a command that is not supported or incomplete (less than 8 bits), the device must complete the cycle gracefully without any impact on the flash content. • An erase command (page, sector, block, chip, etc.) must set all bits inside the designated area (page, sector, block, chip, etc.) to 1 (Fh). • Status Register bit 0 must be set to 1 when a write, erase or write to status register is in progress and cleared to 0 when a write or erase is NOT in progress. • Devices requiring the Write Enable command mst automatically clear the Write Enable Latch at the end of Data Program instructions. • Byte write must be supported. The flexibility to perform a write between 1 byte to 64 bytes is recommended. • Hardware Sequencing requirements are optional in BIOS only platforms. • SPI flash parts that do not meet Hardware sequencing command set requirements may work in BIOS only platforms via software sequencing. 5.23.4.2 Integrated LAN Firmware SPI Flash Requirements A serial flash device that will be used for system BIOS and Integrated LAN or Integrated LAN only must meet all the SPI Based BIOS Requirements plus: • Hardware sequencing • 4, 8 or 64 KBytes erase capability must be supported. 5.23.4.2.1 SPI Flash Unlocking Requirements for Integrated LAN BIOS must ensure there is no SPI flash based read/write/erase protection on the GbE region. GbE firmware and drivers for the integrated LAN need to be able to read, write and erase the GbE region at all times. 5.23.4.3 Intel® Management Engine Firmware SPI Flash Requirements Intel Management Engine Firmware must meet the SPI flash based BIOS Requirements plus: • Hardware Sequencing. • Flash part must be uniform 4 KB erasable block throughout the entire device or for desktop platform only, the flash part may have 64 KB blocks with the first block (lowest address) divided into 4 KB or 8 KB blocks. • Write protection scheme must meet SPI flash unlocking requirements for Management Engine. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 255 Functional Description 5.23.4.3.1 SPI Flash Unlocking Requirements for Management Engine Flash devices must be globally unlocked (read, write and erase access on the ME region) from power on by writing 00h to the flash’s status register to disable write protection. If the status register must be unprotected, it must use the enable write status register command 50h or write enable 06h. Opcode 01h (write to status register) must then be used to write a single byte of 00h into the status register. This must unlock the entire part. If the SPI flash’s status register has non-volatile bits that must be written to, bits [5:2] of the flash’s status register must be all 0h to indicate that the flash is unlocked. If there is no need to execute a write enable on the status register, then opcodes 06h and 50h must be ignored. After global unlock, BIOS has the ability to lock down small sections of the flash as long as they do not involve the ME or GbE region. 5.23.4.4 Hardware Sequencing Requirements The following table contains a list of commands and the associated opcodes that a SPIbased serial flash device must support in order to be compatible with hardware sequencing. Table 5-59. Hardware Sequencing Commands and Opcode Requirements Commands 5.23.4.4.1 Opcode Notes Write to Status Register 01h Writes a byte to SPI flash’s status register. Enable Write to Status Register command must be run prior to this command. Program Data 02h Single byte or 64 byte write as determined by flash part capabilities and software. Read Data 03h Write Disable 04h Read Status 05h Write Enable 06h Outputs contents of SPI flash’s status register Fast Read 0Bh Enable Write to Status Register 50h or 06h Enables a bit in the status register to allow an update to the status register Erase Program mable 256B, 4 Kbyte, 8 Kbyte or 64 Kbyte Full Chip Erase C7h JEDEC ID 9Fh See Section . JEDEC ID Since each serial flash device may have unique capabilities and commands, the JEDEC ID is the necessary mechanism for identifying the device so the uniqueness of the device can be comprehended by the controller (master). The JEDEC ID uses the opcode 9Fh and a specified implementation and usage model. This JEDEC Standard Manufacturer and Device ID read method is defined in Standard JESD21-C, PRN03-NV. 256 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.23.5 Multiple Page Write Usage Model The system BIOS and Intel Active Management Technology firmware (Digital Office only) usage models require that the serial flash device support multiple writes to a page (minimum of 512 writes) without requiring a preceding erase command. BIOS commonly uses capabilities such as counters that are used for error logging and system boot progress logging. These counters are typically implemented by using byte-writes to ‘increment’ the bits within a page that have been designated as the counter. The Intel AMT firmware usage model requires the capability for multiple data updates within any given page. These data updates occur via byte-writes without executing a preceding erase to the given page. Both The BIOS and Intel AMT firmware multiple page write usage models applies to sequential and non-sequential data writes. Note: This usage model requirement is based on any given bit only being written once from a ‘1’ to a ‘0’without requiring the preceding erase. An erase would be required to change bits back to the 1 state. 5.23.5.1 Soft Flash Protection There are two types of flash protection that are not defined in the flash descriptor supported by ICH9: 1. BIOS Range Write Protection 2. SMI#-Based Global Write Protection Both mechanisms are logically OR’d together such that if any of the mechanisms indicate that the access should be blocked, then it is blocked. Table 5-60 provides a summary of the mechanisms. Table 5-60. Flash Protection Mechanism Summary Mechanism Accesses Blocked Range Specific? Reset-Override or SMI#Override? Equivalent Function on FWH BIOS Range Write Protection Writes Yes Reset Override FWH Sector Protection Write Protect Writes No SMI# Override Same as Write Protect in previous ICHs for FWH A blocked command will appear to software to finish, except that the Blocked Access status bit is set in this case. 5.23.5.2 BIOS Range Write Protection The ICH9 provides a method for blocking writes to specific ranges in the SPI flash when the Protected BIOS Ranges are enabled. This is achieved by checking the Opcode type information (which can be locked down by the initial Boot BIOS) and the address of the requested command against the base and limit fields of a Write Protected BIOS range. Note: Once BIOS has locked down the Protected BIOS Range registers, this mechanism remains in place until the next system reset. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 257 Functional Description 5.23.5.3 SMI# Based Global Write Protection The ICH provides a method for blocking writes to the SPI flash when the Write Protected bit is cleared (i.e., protected). This is achieved by checking the Opcode type information (which can be locked down by the initial Boot BIOS) of the requested command. The Write Protect and Lock Enable bits interact in the same manner for SPI BIOS as they do for the FWH BIOS. 5.23.6 Flash Device Configurations The ICH9-based platform may use the serial flash in multiple configurations. The following table focuses on the supported configurations involving the ICH9 and Intel Active Management Technology (Digital Office only). Configuration System BIOS Storage Intel® ICH9 Firmware Minimum Number of SPI Device(s) 1 SPI No 1 2 Non-SPI Yes 1 3 SPI Yes 1 4 Non-SPI No 0 Note: When SPI is selected for BIOS and a SPI device is detected by the ICH9, LPC based BIOS flash is disabled. Note: Firmware includes Intel Active Management Technology (Digital Office only), ASF, Intel Quiet System Technology and Gigabit Ethernet. 5.23.7 SPI Flash Device Recommended Pinout The table below contains the recommended serial flash device pin-out for an 8-pin device. Use of the recommended pin-out on an 8-pin device reduces complexities involved with designing the serial flash device onto a motherboard and allows for support of a common footprint usage model (refer to Section 5.23.8.1). Table 5-61. Recommended Pinout for 8-Pin Serial Flash Device Pin # Signal 1 Chips Select 2 Data Output 3 Write Protect 4 Ground 5 Data Input 6 Serial Clock 7 Hold / Reset 8 Supply Voltage Although an 8-pin device is preferred over a 16-pin device due to footprint compatibility, the following table contains the recommended serial flash device pin-out for a 16-pin SOIC. 258 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.23.8 Serial Flash Device Package Table 5-62. Recommended Pinout for 16-Pin Serial Flash Device 5.23.8.1 Pin # Signal Pin # Signal 1 Hold / Reset 9 Write Protect 2 Supply Voltage 10 Ground 3 No Connect 11 No Connect 4 No Connect 12 No Connect 5 No Connect 13 No Connect 6 No Connect 14 No Connect 7 Chip Select 15 Serial Data In 8 Serial Data Out 16 Serial Clock Common Footprint Usage Model In order to minimize platform motherboard redesign and to enable platform Bill of Material (BOM) selectability, many PC System OEM’s design their motherboard with a single common footprint. This common footprint allows population of a soldered down device or a socket that accepts a leadless device. This enables the board manufacturer to support, via selection of the appropriate BOM, either of these solutions on the same system without requiring any board redesign. The common footprint usage model is desirable during system debug and by flash content developers since the leadless device can be easily removed and reprogrammed without damage to device leads. When the board and flash content is mature for highvolume production, both the socketed leadless solution and the soldered down leaded solution are available through BOM selection. 5.23.8.2 Serial Flash Device Package Recommendations It is highly recommended that the common footprint usage model be supported. An example of how this can be accomplished is as follows: • The recommended pinout for 8-pin serial flash devices is used (refer to Section 5.23.7). • The 8-pin device is supported in either an 8-contact VDFPN (6x5 mm MLP) package or an 8-contact WSON (5x6 mm) package. These packages can fit into a socket that is land pattern compatible with the wide body SO8 package. • The 8-pin device is supported in the SO8 (150 mil) and in the wide-body SO8 (200 mil) packages. The 16-pin device is supported in the SO16 (300 mil) package. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 259 Functional Description 5.24 Intel® Quiet System Technology (Intel® QST) (Desktop Only) The ICH9 implements three PWM and 4 TACH signals for Intel Quiet System Technology (QST). Note: Intel Quiet System Technology functionality requires a correctly configured system, including an appropriate (G)MCH with ME, ME Firmware, and system BIOS support. 5.24.1 PWM Outputs This signal is driven as open-drain. An external pull-up resistor is integrated into the fan to provide the rising edge of the PWM output signal. The PWM output is driven low during reset, which represents 0% duty cycle to the fans. After reset de-assertion, the PWM output will continue to be driven low until one of the following occurs: • The internal PWM control register is programmed to a non-zero value by the Intel QST firmware. • The watchdog timer expires (enabled and set at 4 seconds by default). • The polarity of the signal is inverted by the Intel QST firmware. Note that if a PWM output will be programmed to inverted polarity for a particular fan, then the low voltage driven during reset represents 100% duty cycle to the fan. 5.24.2 TACH Inputs This signal is driven as an open-collector or open-drain output from the fan. An external pull-up is expected to be implemented on the motherboard to provide the rising edge of the TACH input. This signal has analog hysteresis and digital filtering due to the potentially slow rise and fall times. This signal has a weak internal pull-up resistor to keep the input buffer from floating if the TACH input is not connected to a fan. 5.25 Thermal Sensors ICH9 integrates two thermal sensors that monitor the temperature within its die. The thermal sensors are used for Intel®Quiet System Technology (Intel®QST). The Intel QST firmware can internally access the temperature measured by the sensors and use the data as a factor to determine how to control the fans. The ICH9 thermal sensors also provide the capability to protect the ICH9 under a catastrophic thermal situation. When the sensors are enabled and correctly programmed by the system BIOS, the ICH9 will shut down the system when the ICH9 thermal limit is reached. Refer to the Thermal Memory Mapped Configuration Registers Section 23.2 for more info on the catastrophic settings. 260 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Functional Description 5.26 Feature Capability Mechanism A set of registers is included in the ICH9 LPC Interface (Device 31, Function 0, offset E0h - EBh) that allows the system software or BIOS to easily determine the features supported by ICH9. These registers can be accessed through LPC PCI configuration space, thus allowing for convenient single point access mechanism for chipset feature detection. This set of registers consists of: Capability ID (FDCAP) Capability Length (FDLEN) Capability Version and Vendor-Specific Capability ID (FDVER) Feature Vector (FVECT) 5.27 Integrated Trusted Platform Module (Mobile Only) The integrated TPM (TPM) implementation consists of firmware, Intel® Management Engine resources and dedicated hardware within the ICH and the (G)MCH. The integrated TPM supports all requirements of the TPM Specification Version 1.2, Level 2 Revision 103, as published by the Trusted Computing Group. Note: Integrated TPM functionality requires a correctly configured system, including an appropriate mobile (G)MCH with Intel Management Engine firmware, ICH9M and SPI Flash. 5.27.1 Integrated TPM Hardware Requirements The following hardware components are required for TPM 1.2 functionality : 1. SPI Flash Memory: The SPI flash component connected to the ICH (SPI interface) provides non-volatile storage requirement for the integrated TPM. It contains the FW code which is loaded by the Intel Management Engine upon power on. 2. Monotonic Counters: The ICH9M contains four TPM 1.2 compliant monotonic counters that reside in the RTC well which maintains values programmed by the integrated TPM across power cycles. The counters are only incremented by TPM software (host or ME) and are not controlled by the ICH hardware. 3. Physical Presence: Physical presence indication is required in order to enable certain TPM commands. These commands are generally used to bypass owner authorized commands when the authorization data is unavailable or to set the integrated TPM to a non-owner state. The Management Engine Firmware uses the CLGPIO5 pin on the ICH9M to indicate Physical Presence to the platform when pulled high. In addition, Physical Presence flags can be set to force Physical Presence by firmware. 4. Chipset: An ICH9M and (G)MCH with Intel Management Engine enabled is required for integrated TPM support. 5.27.2 Enabling integrated TPM The integrated TPM is enabled based on the combination of a functional strap on both the ICH and the MCH and a soft strap bit found in the SPI Descriptor. When the integrated TPM is enabled, Front Side Bus cycles that would otherwise propagate to the LPC bus will be routed by the Config Bus Decoder to the integrated TPM Host Decoder. Either Functional strap or the soft strap bit may be used to disable the integrated TPM. • ICH Functional Strap: The ICH9M enables Integrated TPM when SPI_MOSI is sampled high on the rising edge of CLPWROK and disabled if the SPI_MOSI signal is sampled low. See Section 2.24.1 for details. The SPI_MOSI signal requires an Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 261 Functional Description external pull-up resistor to enable the integrated TPM. SPI_MOSI has an integrated pull-down resistor enabled at reset only and does not require an external pull-down resistor to disable integrated TPM. • Soft Strap: The integrated TPM Disable bit (bit 2) in the MCHSTRP0 register (FSMBA + 0h) within the flash descriptor can act as an override to the functional straps on both the ICH and MCH. When set, the integrated TPM will be disabled regardless of the values of the functional straps on the ICH and/or MCH. This bit along with both functional straps must be appropriately configured to enable integrated TPM. • (G)MCH Functional Strap: For (G)MCH functional strap information, consult the appropriate MCH EDS. §§ 262 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition 6 Ballout Definition This chapter contains the Intel® ICH9 ballout information. 6.1 Intel® ICH9 Ballout (Desktop Only) This section contains the ICH9 ballout. Figure 6-1 and Figure 6-2 show the ballout from a top of the package view. Table 6-1 is the BGA ball list, sorted alphabetically by signal name. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 263 Ballout Definition Figure 6-1. 1 Intel® ICH9 Ballout (Top view–Left Side) (Desktop Only) 2 3 4 5 6 7 8 9 10 GPIO12 GPIO14 / CLGPIO2 VccLAN1_0 5 Vss Vcc3_3 VccLAN1_0 5 A Vss Vcc3_3 PIRQD# AD11 AD4 V5REF GNT1# / GPIO51 B Vcc3_3 Vss PCICLK AD9 Vss AD8 AD7 DEVSEL# GNT2# / GPIO53 C AD24 AD25 AD26 D AD27 AD15 AD21 C/BE2# AD14 AD1 AD3 AD0 11 12 13 14 15 SMLINK0 A GPIO27 VccLAN3_3 SLP_S3# GPIO24 / MEM_LED Vss VccLAN3_3 SLP_S4# Vss SMLINK1 B PLTRST# STP_PCI# / GPIO15 C S4_STATE# GPIO57 / / GPIO26 CLGPIO5 TP0 D LAN_RSTS LAN_RXD2 YNC E PIRQB# Vss PAR AD16 TRDY# AD10 C/BE3# AD2 AD6 AD18 AD5 Vss F PIRQC# PIRQG# / GPIO4 AD29 PERR# Vss GNT3# / GPIO55 AD13 Vss STOP# C/BE0# Vss REQ2# / GPIO52 LAN_TXD1 LAN_TXD0 F G AD30 PIRQH# / GPIO5 C/BE1# AD19 Vcc3_3 FRAME# REQ1# / GPIO50 LAN_TXD2 LAN_RXD0 G H FWH1 / LAD1 Vss Vcc1_5_A Vcc1_5_A AD12 Vss LAN_RXD1 VccSus3_3 H J FWH3 / LAD3 K E Vcc3_3 AD23 AD20 AD17 REQ3# / GPIO54 Vss AD31 GNT0# AD22 Vcc3_3 PLOCK# Vcc3_3 LDRQ1# / GPIO23 PIRQA# Vss AD28 IRDY# J GPIO18 GPIO32 FWH0 / LAD0 SERR# PIRQE# / GPIO2 REQ0# Vcc3_3 K L SATACLKR EQ# / GPIO35 Vss RCIN# FWH4 / LFRAME# LDRQ0# PIRQF# / GPIO3 Vcc3_3 L M OC7# / GPIO31 GPIO16 INIT3_3V# CLK14 Vss FWH2 / LAD2 Vss Vcc1_05 Vcc1_05 Vss Vcc1_05 M N OC5# / GPIO29 OC4# / GPIO43 OC1# / GPIO40 OC6# / GPIO30 SERIRQ GPIO0 SPKR Vcc1_05 Vss Vss Vss N P OC11# / GPIO47 Vss OC8# / GPIO44 OC0# / GPIO59 Vss OC2# / GPIO41 A20GATE Vss Vss Vss Vss P R SUS_STAT # / LPCPD PCIRST# PME# SUSCLK OC9# / GPIO45 OC3# / GPIO42 Vss Vcc1_05 Vss Vss Vss R CLPWROK OC10# / GPIO46 CK_PWRG D Vss Vss Vss Vss T U Vss Vss T Vcc1_5_A U VccSus3_3 VccSus3_3 VccSus3_3 V USBP11N USBP11P Vss USBP9P USBP9N W Vss USBP10N USBP10P Vss Vss Y USBP8N USBP8P Vss USBP6P USBP6N Vss VccSus3_3 Y AA Vss USBP7P USBP7N Vss Vss Vcc1_5_A Vcc1_5_A AA AB USBP5N USBP5P Vss USBP3P USBP3N Vcc1_5_A Vcc1_5_A AC Vss USBP4P USBP4N Vss Vss VccSus1_05 Vss VccSusHDA VccHDA Vcc1_5_A Vss Vcc1_5_A Vcc1_5_A Vcc1_5_A AC AD USBP2N USBP2P Vss USBP0P USBP0N Vss VccSus1_5 Vss Vcc3_3 Vcc1_5_A Vcc1_5_A Vcc1_5_A Vss Vss AD AE Vss USBP1P USBP1N Vss Vss SATALED# Vss Vss Vss Vcc1_5_A Vss Vss Vss Vss AE Vss GPIO20 GPIO33 Vss SATA5TXN Vss SATA4TXN Vcc1_5_A SATA3TXN Vss SATA2TXP Vss AF AF V5REF_Sus VccSus3_3 AG USBRBIAS# USBRBIAS AH HDA_SDIN2 AJ HDA_RST# AK HDA_SYNC Vss 1 2 264 Vss PWRBTN# VccSus3_3 VccSus3_3 VccSus3_3 VccSus3_3 Vcc1_05 Vss Vss Vss VccSus3_3 Vcc1_05 Vss Vss Vss V VccSus3_3 VccSus3_3 Vcc1_05 Vcc1_05 Vss Vcc1_05 W Vss AB CLK48 AG HDA_BIT_C HDA_SDIN1 LK HDA_SDOU HDA_SDIN3 T GPIO34 Vss SATA5TXP Vss SATA4TXP Vcc1_5_A Vcc1_5_A SATA3TXP Vss SATA2TXN Vss AH Vss Vss SATARBIAS SATA5RXN Vss SATA4RXN Vcc1_5_A SATA3RXN Vss SATA2RXN Vss SATA1RXN AJ HDA_SDIN0 Vcc3_3 VccUSBPLL SATARBIAS SATA5RXP # Vss SATA4RXP Vcc1_5_A SATA3RXP Vss SATA2RXP Vss SATA1RXP AK 3 4 5 8 9 10 11 12 13 14 15 6 7 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Figure 6-2. 16 Intel® ICH9 Ballout (Top view–Right Side) (Desktop Only) 17 18 19 20 21 GPIO13 GPIO8 RTCX1 VccRTC VccCL1_05 Vcc1_05 RTCRST# RTCX2 Vss VccCL3_3 Vcc1_05 Vss SPI_MISO Vss VRMPWRG VccCL3_3 D Vcc1_05 PWROK SPI_MOSI CL_VREF0 A TP6 VccSus3_3 GPIO9 / WOL_EN B TP7 Vss STP_CPU# / GPIO25 Vss VccSus3_3 C SMBALERT # / GPIO11 GPIO10 / CLGPIO1 TP5 SST VccSus3_3 LAN_RST# 22 23 24 25 26 27 F SMBDATA VccSus3_3 GPIO56 SLP_M# Vss TP4 LINKALERT# SYS_RESE / GPIO60 / T# CLGPIO4 29 30 Vss A GLAN_COM VccGLAN1_ PI 5 B VccGLAN1_ VccGLAN1_ VccGLAN1_ 5 5 5 C PERn6 / PERp6 / GLAN_RXN GLAN_RXP D Vss Vss D E 28 VccGLAN3_ VccGLANPL GLAN_COM VccCL1_5 3 L PO WAKE# LAN100_SL P Vss INTVRMEN Vcc1_05 SPI_CS0# PETn6 / GLAN_TXN PETp6 / GLAN_TXP Vss Vss E TP3 Vss RSMRST# SPI_CS1# / GPIO58 / CLGPIO6 Vcc1_05 GLAN_CLK Vss Vss PERp5 PERn5 F RI# CL_RST0# INTRUDER# CL_CLK0 SPI_CLK Vcc1_05 Vss PETn5 PETp5 Vss Vss G Vss SRTCRST# CL_DATA0 Vcc1_05 Vcc1_05 Vss Vss Vss PERp4 PERn4 H J Vcc1_05 Vcc1_5_B Vcc1_5_B PETn4 PETp4 Vss Vss J K Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss Vss PERp3 PERn3 K L Vss Vcc1_5_B Vcc1_5_B PETn3 PETp3 Vss Vss L G Vss H SMBCLK SLP_S5# GPIO28 VccSus1_05 VccSus1_5 Vss M Vss Vcc1_05 Vcc1_05 Vcc1_05 Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss Vss PERp2 PERn2 M N Vss Vss Vss Vcc1_05 Vss Vcc1_5_B Vcc1_5_B PETn2 PETp2 Vss Vss N P Vss Vss Vss Vss Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss Vss PERp1 PERn1 P R Vss Vss Vss Vcc1_05 Vss Vcc1_5_B Vcc1_5_B PETn1 PETp1 Vss Vss R T Vss Vss Vss Vss Vcc1_5_B Vcc1_5_B Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss VccDMIPLL T U Vss Vss Vss Vcc1_05 Vss Vcc1_5_B DMI_CLKP DMI_CLKN Vcc1_5_B Vcc1_5_B Vcc1_5_B U V Vss Vss Vss Vcc1_05 Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss Vss DMI0TXP DMI0TXN V W Vss Vcc1_05 Vcc1_05 Vcc1_05 Vss Vcc1_5_B Vcc1_5_B DMI0RXP DMI0RXN Vss Vss W Y Vcc1_5_B Vcc1_5_B Vcc1_5_B Vss Vss DMI1TXP DMI1TXN Y AA Vcc1_5_B Vcc1_5_B Vcc1_5_B DMI1RXN DMI1RXP Vss Vss AA Vcc1_5_A Vcc1_5_B Vcc1_5_B Vss Vss DMI2TXP DMI2TXN AB PECI Vss Vcc1_5_B DMI2RXN DMI2RXP Vss Vss AC Vcc1_5_B Vcc1_5_B Vcc1_5_B DMI3TXN DMI3TXP AD AB AC Vcc1_5_A Vcc1_5_A Vcc1_5_A Vcc3_3 AD Vss Vcc1_5_A Vss Vss SDATAOUT SATA5GP 1 / GPIO48 AE Vss Vcc1_5_A Vss Vss SATA1GP / SATA2GP / SATA3GP / GPIO19 GPIO36 GPIO37 AF SATA1TXP Vcc1_5_A SATA_CLKN SATA_CLK P Vcc1_5_A Vss Vcc3_3 Vcc3_3 IGNNE# Vss SATA4GP CPUPWRG THRMTRIP D # INIT# TP2 Vss DMI3RXP Vcc1_5_B Vcc1_5_B Vcc1_5_B AE Vss NMI Vss DMI3RXN DMI_IRCO MP Vss DMI_ZCOM P AF Vss VccDMI VccDMI AG AG AH SATA1TXN Vcc1_5_A Vcc1_5_A Vss Vss TACH0 / GPIO17 TACH2 / GPIO6 SDATAOUT 0 / GPIO39 Vcc3_3 MCH_SYNC # SMI# INTR V_CPU_IO Vss Vcc3_3 AH GPIO49 Vss FERR# A20M# STPCLK# V_CPU_IO AJ AK AJ Vss SATA0RXP Vcc1_5_A SATA0TXP Vss PWM0 PWM1 Vss SCLOCK / GPIO22 AK Vss SATA0RXN Vcc1_5_A SATA0TXN VccSATAPL L TACH1 / GPIO1 PWM2 TACH3 / GPIO7 SLOAD / GPIO38 SATA0GP / GPIO21 THRM# Vss TP1 Vss Vss 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 265 Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) 266 Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # A20GATE P8 CL_CLK0 G22 GNT0# H5 A20M# AJ28 CL_DATA0 H21 GNT1# / GPIO51 A7 AD0 C10 CL_RST0# G20 GNT2# / GPIO53 C7 AD1 C8 CL_VREF0 C27 GNT3# / GPIO55 F7 AD2 E9 CLK14 M5 GPIO0 N7 AD3 C9 CLK48 AG3 GPIO8 A20 AD4 A5 CLPWROK T6 GPIO9 / WOL_EN A18 AD5 E12 CPUPWRGD AD23 GPIO10 / CLGPIO1 C17 AD6 E10 DEVSEL# C6 GPIO12 A8 AD7 B7 DMI_CLKN U26 GPIO13 A19 AD8 B6 DMI_CLKP U25 GPIO14 / CLGPIO2 A9 AD9 B4 DMI_IRCOMP AF28 GPIO16 M2 AD10 E7 DMI_ZCOMP AF30 GPIO18 K1 AD11 A4 DMI0RXN W28 GPIO20 AF5 AD12 H12 DMI0RXP W26 GPIO24 / MEM_LED A14 AD13 F8 DMI0TXN V30 GPIO27 A11 AD14 C5 DMI0TXP V29 GPIO28 G18 AD15 D2 DMI1RXN AA26 GPIO32 K2 AD16 E5 DMI1RXP AA28 GPIO33 AF6 AD17 G7 DMI1TXN Y30 GPIO34 AH5 AD18 E11 DMI1TXP Y29 GPIO49 AJ25 AD19 G10 DMI2RXN AC26 GPIO56 F16 AD20 G6 DMI2RXP AC28 GPIO57 / CLGPIO5 C12 AD21 D3 DMI2TXN AB30 HDA_BIT_CLK AH3 AD22 H6 DMI2TXP AB29 HDA_RST# AJ1 AD23 G5 DMI3RXN AF26 HDA_SDIN0 AK3 AD24 C1 DMI3RXP AE26 HDA_SDIN1 AH4 AD25 C2 DMI3TXN AD29 HDA_SDIN2 AH1 AD26 C3 DMI3TXP AD30 HDA_SDIN3 AJ3 AD27 D1 FERR# AJ27 HDA_SDOUT AJ2 AD28 J7 FRAME# G12 HDA_SYNC AK1 AD29 F3 FWH0 / LAD0 K3 IGNNE# AC22 AD30 G1 FWH1 / LAD1 H1 INIT# AE23 AD31 H3 FWH2 / LAD2 M7 INIT3_3V# M3 C/BE0# F11 FWH3 / LAD3 J1 INTR AH27 C/BE1# G9 FWH4 / LFRAME# L5 INTRUDER# G21 C/BE2# C4 GLAN_CLK F25 INTVRMEN E23 C/BE3# E8 GLAN_COMPI B29 IRDY# J8 CK_PWRGD T8 GLAN_COMPO A29 LAN_RST# C21 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball # Ball Name Ball # Ball Name Ball # LAN_RSTSYNC E14 PERp4 H29 RTCRST# A25 LAN_RXD0 G15 PERp5 F29 RTCX1 A21 LAN_RXD1 H14 PERp6 / GLAN_RXP D30 RTCX2 B21 LAN_RXD2 E13 PERR# F5 LAN_TXD0 F15 PETn1 R26 S4_STATE# / GPIO26 C11 LAN_TXD1 F14 PETn2 N26 SATA_CLKN AF18 LAN_TXD2 G14 PETn3 L26 SATA_CLKP AF19 SATA0GP / GPIO21 AK25 SATA0RXN AK17 SATA0RXP AJ17 SATA0TXN AK19 SATA0TXP AJ19 LAN100_SLP E21 PETn4 J26 LDRQ0# L6 PETn5 G26 LDRQ1# / GPIO23 J3 LINKALERT# / GPIO60 / CLGPIO4 F18 MCH_SYNC# AH25 NMI AF24 OC0# / GPIO59 P5 OC1# / GPIO40 N3 OC2# / GPIO41 P7 OC3# / GPIO42 R7 OC4# / GPIO43 N2 OC5# / GPIO29 N1 OC6# / GPIO30 N5 OC7# / GPIO31 M1 OC8# / GPIO44 P3 OC9# / GPIO45 R6 OC10# / GPIO46 T7 OC11# / GPIO47 P1 PAR E3 PCICLK B3 PCIRST# R2 PECI AC23 PERn1 P30 PERn2 M30 PERn3 K30 PERn4 H30 PERn5 F30 PERn6 / GLAN_RXN D29 PERp1 P29 PERp2 M29 PERp3 K29 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PETn6 / GLAN_TXN E26 PETp1 R28 PETp2 N28 PETp3 L28 PETp4 J28 PETp5 G28 PETp6 / GLAN_TXP E28 PIRQA# J5 PIRQB# E1 PIRQC# F1 PIRQD# A3 PIRQE# / GPIO2 K6 PIRQF# / GPIO3 L7 PIRQG# / GPIO4 F2 PIRQH# / GPIO5 G2 PLOCK# H8 PLTRST# C14 PME# R3 PWM0 AJ21 PWM1 AJ22 PWM2 AK22 PWRBTN# T3 PWROK C25 RCIN# L3 REQ0# K7 REQ1# / GPIO50 G13 SATA1GP / GPIO19 AE20 SATA1RXN AJ15 SATA1RXP AK15 SATA1TXN AH16 SATA1TXP AF16 SATA2GP / GPIO36 AE21 SATA2RXN AJ13 SATA2RXP AK13 SATA2TXN AH14 SATA2TXP AF14 SATA3GP / GPIO37 AE22 SATA3RXN AJ11 SATA3RXP AK11 SATA3TXN AF12 SATA3TXP AH12 SATA4GP AF22 SATA4RXN AJ9 SATA4RXP AK9 SATA4TXN AF10 SATA4TXP AH9 SATA5GP AD21 SATA5RXN AJ7 SATA5RXP AK7 SATA5TXN AF8 REQ2# / GPIO52 F13 REQ3# / GPIO54 G8 SATA5TXP AH7 RI# G19 L1 RSMRST# F22 SATACLKREQ# / GPIO35 SATALED# AE7 267 Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # SATARBIAS AJ6 TACH2 / GPIO6 AH22 V_CPU_IO AH28 SATARBIAS# AK6 TACH3 / GPIO7 AK23 V_CPU_IO AJ30 SCLOCK / GPIO22 AJ24 THRM# AK26 V5REF A6 SDATAOUT0 / GPIO39 AH23 THRMTRIP# AD24 V5REF_Sus AF1 TP0 C13 Vcc1_05 A24 SDATAOUT1 / GPIO48 AD20 TP1 AK28 Vcc1_05 B24 SERIRQ N6 TP2 AE24 Vcc1_05 C24 SERR# K5 TP3 F20 Vcc1_05 E24 SLOAD / GPIO38 AK24 TP4 E19 Vcc1_05 F24 SLP_M# F17 TP5 C18 Vcc1_05 G24 SLP_S3# A13 TP6 A16 Vcc1_05 H23 SLP_S4# B13 TP7 B16 Vcc1_05 H24 SLP_S5# G17 TRDY# E6 Vcc1_05 J23 SMBALERT# / GPIO11 USBP0N AD6 Vcc1_05 M12 C16 USBP0P AD5 Vcc1_05 M13 SMBCLK H16 USBP1N AE3 Vcc1_05 M15 SMBDATA E16 USBP1P AE2 Vcc1_05 M17 SMI# AH26 USBP2N AD1 Vcc1_05 M18 SMLINK0 A15 USBP2P AD2 Vcc1_05 M19 SMLINK1 B15 USBP3N AB6 Vcc1_05 N12 SPI_CLK G23 USBP3P AB5 Vcc1_05 N19 SPI_CS0# E25 USBP4N AC3 Vcc1_05 R12 USBP4P AC2 Vcc1_05 R19 SPI_CS1# / GPIO58 / CLGPIO6 F23 USBP5N AB1 Vcc1_05 U12 SPI_MISO B26 USBP5P AB2 Vcc1_05 U19 SPI_MOSI C26 USBP6N Y6 Vcc1_05 V12 SPKR N8 USBP6P Y5 Vcc1_05 V19 SRTCRST# H20 USBP7N AA3 Vcc1_05 W12 SST C19 USBP7P AA2 Vcc1_05 W13 STOP# F10 USBP8N Y1 Vcc1_05 W15 STP_CPU# / GPIO25 B18 USBP8P Y2 Vcc1_05 W17 STP_PCI# / GPIO15 C15 USBP9N V6 Vcc1_05 W18 STPCLK# AJ29 USBP9P V5 Vcc1_05 W19 SUS_STAT# / LPCPD USBP10N W2 Vcc1_5_A AA7 R1 USBP10P W3 Vcc1_5_A AA8 SUSCLK R5 USBP11N V1 Vcc1_5_A AB7 USBP11P V2 Vcc1_5_A AB8 USBRBIAS AG2 Vcc1_5_A AB23 USBRBIAS# AG1 Vcc1_5_A AC11 SYS_RESET# F19 TACH0 / GPIO17 AH21 TACH1 / GPIO1 268 Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) AK21 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Ball # Ball Name Vcc1_5_A AC13 Vcc1_5_A AC14 Vcc1_5_A Vcc1_5_A Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball # Ball Name Ball # Vcc1_5_B J25 Vcc3_3 AK4 Vcc1_5_B K23 Vcc3_3 A2 AC15 Vcc1_5_B K24 Vcc3_3 B1 AC16 Vcc1_5_B K25 Vcc3_3 B9 Vcc1_5_A AC17 Vcc1_5_B L24 Vcc3_3 G3 Vcc1_5_A AC18 Vcc1_5_B L25 Vcc3_3 G11 Vcc1_5_A AC20 Vcc1_5_B M23 Vcc3_3 H7 Vcc1_5_A AD11 Vcc1_5_B M24 Vcc3_3 J2 Vcc1_5_A AD12 Vcc1_5_B M25 Vcc3_3 K8 Vcc1_5_A AD13 Vcc1_5_B N24 Vcc3_3 L8 Vcc1_5_A AD17 Vcc1_5_B N25 VccCL1_05 A23 Vcc1_5_A AE11 Vcc1_5_B P23 VccCL1_5 A26 Vcc1_5_A AE17 Vcc1_5_B P24 VccCL3_3 B23 Vcc1_5_A AF11 Vcc1_5_B P25 VccCL3_3 C23 Vcc1_5_A AF17 Vcc1_5_B R24 VccDMI AG29 Vcc1_5_A AH10 Vcc1_5_B R25 VccDMI AG30 Vcc1_5_A AH11 Vcc1_5_B T23 VccDMIPLL T30 Vcc1_5_A AH17 Vcc1_5_B T24 VccGLAN1_5 B30 Vcc1_5_A AH18 Vcc1_5_B T25 VccGLAN1_5 C28 Vcc1_5_A AJ10 Vcc1_5_B T26 VccGLAN1_5 C29 Vcc1_5_A AJ18 Vcc1_5_B T28 VccGLAN1_5 C30 Vcc1_5_A AK10 Vcc1_5_B U24 VccGLAN3_3 A27 Vcc1_5_A AK18 Vcc1_5_B U28 VccGLANPLL A28 Vcc1_5_A H10 Vcc1_5_B U29 VccHDA AC10 Vcc1_5_A H11 Vcc1_5_B U30 VccLAN1_05 A10 Vcc1_5_A T1 Vcc1_5_B V23 VccLAN1_05 B10 Vcc1_5_B AA23 Vcc1_5_B V24 VccLAN3_3 A12 Vcc1_5_B AA24 Vcc1_5_B V25 VccLAN3_3 B12 Vcc1_5_B AA25 Vcc1_5_B W24 VccRTC A22 Vcc1_5_B AB24 Vcc1_5_B W25 VccSATAPLL AK20 Vcc1_5_B AB25 Vcc1_5_B Y23 VccSus1_05 AC7 Vcc1_5_B AC25 Vcc1_5_B Y24 VccSus1_05 H17 Vcc1_5_B AD25 Vcc1_5_B Y25 VccSus1_5 AD8 Vcc1_5_B AD26 Vcc3_3 AC19 VccSus1_5 H18 Vcc1_5_B AD28 Vcc3_3 AC21 VccSus3_3 AF2 Vcc1_5_B AE28 Vcc3_3 AD10 VccSus3_3 A17 Vcc1_5_B AE29 Vcc3_3 AF21 VccSus3_3 B20 Vcc1_5_B AE30 Vcc3_3 AH24 VccSus3_3 C20 Vcc1_5_B J24 Vcc3_3 AH30 VccSus3_3 E17 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 269 Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) 270 Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # VccSus3_3 H15 Vss AD22 Vss AJ20 VccSus3_3 U1 Vss AE1 Vss AJ23 VccSus3_3 U2 Vss AE5 Vss AJ26 VccSus3_3 U3 Vss AE6 Vss AK2 VccSus3_3 U5 Vss AE8 Vss AK8 VccSus3_3 U6 Vss AE9 Vss AK12 VccSus3_3 U7 Vss AE10 Vss AK14 VccSus3_3 U8 Vss AE12 Vss AK16 VccSus3_3 V8 Vss AE13 Vss AK27 VccSus3_3 W7 Vss AE14 Vss AK29 VccSus3_3 W8 Vss AE15 Vss AK30 VccSus3_3 Y8 Vss AE16 Vss A1 VccSusHDA AC9 Vss AE18 Vss A30 VccUSBPLL AK5 Vss AE19 Vss B2 VRMPWRGD C22 Vss AE25 Vss B5 Vss AA1 Vss AF3 Vss B8 Vss AA5 Vss AF7 Vss B11 Vss AA6 Vss AF9 Vss B14 Vss AA29 Vss AF13 Vss B17 Vss AA30 Vss AF15 Vss B19 Vss AB3 Vss AF20 Vss B22 Vss AB26 Vss AF23 Vss B25 Vss AB28 Vss AF25 Vss B27 Vss AC1 Vss AF29 Vss B28 Vss AC5 Vss AG28 Vss D28 Vss AC6 Vss AH2 Vss E2 Vss AC8 Vss AH6 Vss E15 Vss AC12 Vss AH8 Vss E18 Vss AC24 Vss AH13 Vss E22 Vss AC29 Vss AH15 Vss E29 Vss AC30 Vss AH19 Vss E30 Vss AD3 Vss AH20 Vss F6 Vss AD7 Vss AH29 Vss F9 Vss AD9 Vss AJ4 Vss F12 Vss AD14 Vss AJ5 Vss F21 Vss AD15 Vss AJ8 Vss F26 Vss AD16 Vss AJ12 Vss F28 Vss AD18 Vss AJ14 Vss G16 Vss AD19 Vss AJ16 Vss G25 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Table 6-1. Intel® ICH9 Ballout by Signal Name (Desktop Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # Vss G29 Vss P15 Vss V15 Vss G30 Vss P16 Vss V16 Vss H2 Vss P17 Vss V17 Vss H9 Vss P18 Vss V18 Vss H13 Vss P19 Vss V26 Vss H19 Vss P26 Vss V28 Vss H22 Vss P28 Vss W1 Vss H25 Vss R8 Vss W5 Vss H26 Vss R13 Vss W6 Vss H28 Vss R14 Vss W14 Vss J6 Vss R15 Vss W16 Vss J29 Vss R16 Vss W23 Vss J30 Vss R17 Vss W29 Vss K26 Vss R18 Vss W30 Vss K28 Vss R23 Vss Y3 Vss L2 Vss R29 Vss Y7 Vss L23 Vss R30 Vss Y26 Vss L29 Vss T2 Vss Y28 Vss L30 Vss T5 WAKE# E20 Vss M6 Vss T12 Vss M8 Vss T13 Vss M14 Vss T14 Vss M16 Vss T15 Vss M26 Vss T16 Vss M28 Vss T17 Vss N13 Vss T18 Vss N14 Vss T19 Vss N15 Vss T29 Vss N16 Vss U13 Vss N17 Vss U14 Vss N18 Vss U15 Vss N23 Vss U16 Vss N29 Vss U17 Vss N30 Vss U18 Vss P2 Vss U23 Vss P6 Vss V3 Vss P12 Vss V7 Vss P13 Vss V13 Vss P14 Vss V14 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 271 Ballout Definition 6.2 Intel® 82801IBM ICH9M and 82801IEM ICH9M-E Ballout (Mobile Only) This section contains the 82801IBM ICH9M and 82801IEM ICH9M-E ballout. Figure 6-3 and Figure 6-4 show the ballout from the top of the package view. Table 6-2 is the BGA ball list, sorted alphabetically by signal name. 272 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Intel® ICH9M and ICH9M-E Ballout (Top View–Left Side) (Mobile Only) Figure 6-3. 1 2 3 4 5 6 7 8 GPIO57 / CLGPIO5 9 GPIO27 10 11 12 13 A VSS VSS AD14 STOP# C/BE3# V5REF GNT1# / GPIO51 B VSS VSS AD19 C/BE1# VSS REQ1# / GPIO50 AD7 VSS Vcc3_3 C AD24 PLOCK# AD21 PIRQD# AD9 DEVSEL# AD8 AD1 AD5 D AD27 AD15 IRDY# PCICLK AD17 C/BE2# FRAME# C/BE0# AD2 AD18 AD0 AD13 VSS AD4 AD6 VSS AD3 LAN_TXD2 14 VccLAN1_0 VccLAN1_ VccLAN3_ SMBDATA STP_PCI# 5 05 3 GPIO56 VSS 15 Vcc1_05 A VSS Vcc1_05 B PLTRST# Vcc1_05 C LAN_TXD1 LAN_TXD0 LAN_RXD2 Vcc1_05 D VccLAN3_ BATLOW# 3 GPIO14 / LAN_PHY_ S4_STATE# LAN_RSTS AC_PRESE PWR_CTRL / GPIO26 YNC NT / GPIO12 E PIRQB# VSS PAR PERR# VSS REQ3# / GPIO54 F REQ0# PIRQG# / GPIO4 AD22 AD23 TRDY# GNT3# / GPIO55 AD20 AD11 Vcc3_3 AD16 AD12 GNT2# / GPIO53 REQ2# / GPIO52 G AD30 PIRQH# / GPIO5 Vcc3_3 GNT0# AD28 Vcc3_3 AD25 VSS Vcc1_5_A Vcc1_5_A AD10 VSS LAN_RXD1 H CLK14 VSS AD31 PIRQE# / GPIO2 VSS AD29 AD26 H J LDRQ1# / GPIO23 Vcc3_3 LDRQ0# SERR# PIRQA# PIRQC# Vcc3_3 J K GPIO18 FWH3 / LAD3 FWH4 / LFRAME# FWH1 / LAD1 FWH0 / LAD0 PIRQF# / GPIO3 Vcc3_3 K L SATACLK REQ# / GPIO35 VSS RCIN# CLKRUN# VSS FWH2 / LAD2 VSS Vcc1_05 Vcc1_05 VSS Vcc1_05 VSS L VSS Vcc1_05 E LAN_RXD0 Vcc1_05 F VSS G M OC4# / DPRSLPVR GPIO43 / GPIO16 OC7# / GPIO31 OC6# / GPIO30 SERIRQ PMSYNC# / GPIO0 SPKR Vcc1_05 VSS VSS VSS VSS M N OC9# / GPIO45 OC5# / GPIO29 OC8# / GPIO44 OC0# / GPIO59 OC1# / GPIO40 OC2# / GPIO41 A20GATE VSS VSS VSS VSS VSS N P SUSCLK VSS OC11# / GPIO47 VSS OC10# / GPIO46 OC3# / GPIO42 VSS Vcc1_05 VSS VSS VSS VSS P R PCIRST# PME# PWRBTN# VSS VSS VSS VSS VSS R T VccSus3 VccSus3_3 VccSus3_3 VccSus3_3 VccSus3_3 VccSus3_3 VccSus3_3 _3 Vcc1_05 VSS VSS VSS VSS T U USBP11N USBP11P Vcc1_05 VSS VSS VSS VSS U Vcc1_05 Vcc1_05 VSS Vcc1_05 VSS SUS_STAT CK_PWRG CLPWROK # / LPCPD D VSS USBP10P V VSS USBP9N USBP9P VSS USBP10N VccSus3_3 VccSus3_3 VSS VccSus3_3 VccSus3_3 W USBP8N USBP8P VSS USBP6P USBP6N VccSus3_3 VccSus3_3 Y VSS USBP7P USBP7N VSS VSS VccSus3_3 VccSus3_3 AA USBP5N USBP5P VSS USBP3P USBP3N VSS Vcc1_5_A AB VSS USBP4N USBP4P VSS VSS Vcc1_5_A Vcc1_5_A AC USBP2N USBP2P VSS USBP0P USBP0N Vcc1_5_A Vcc1_5_A AD VSS USBP1P USBP1N VSS VSS VSS VSS V W Y AA AB VccSus1_0 Vcc1_5_A 5 Vcc3_3 Vcc1_5_A Vcc1_5_A Vcc1_5_A Vcc1_5_A AC VccSus1_5 VSS VSS Vcc1_5_A VSS VSS VSS Vcc1_5_A AD HDA_DOCK HDA_RST# _RST# / GPIO34 VSS SATA5TXN Vcc1_5_A VSS VSS VSS Vcc1_5_A AE AE V5REF_S us VSS VSS VSS HDA_SDIN 3 VSS AF VccSus3 _3 VSS CLK48 HDA_SDIN 0 VSS HDA_BIT_ CLK VSS GPIO20 VSS SATA5TXP Vcc1_5_A SATA4TXP VSS SATA1TXP Vcc1_5_A AF AG USBRBIA USBRBIAS S# VSS HDA_DOC K_EN# / GPIO33 SATALED# VSS Vcc1_5_A Vcc1_5_A SATA4TXN VSS SATA1TXN Vcc1_5_A AG VSS VSS SATARBIAS VSS SATA5RXN Vcc1_5_A SATA4RXN VSS SATA1RXN VSS Vcc1_5_A AH AJ VSS HDA_SDIN HDA_SDO 1 UT AH VSS VSS HDA_SDIN HDA_SYN 2 C AJ VSS VSS VccSusHD A VccHDA VccUSBPL L Vcc3_3 SATARBIAS # VSS SATA5RXP Vcc1_5_A SATA4RXP VSS SATA1RXP VSS Vcc1_5_A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 273 Ballout Definition Figure 6-4. 16 Intel® ICH9M and ICH9M-E Ballout (Top View–Right Side) (Mobile Only) 17 18 20 21 22 VccRTC VccCL3_3 RTCRST# VSS VccCL3_3 VSS VSS RTCX1 RTCX2 CL_VREF0 VSS SLP_M# VSS C SLP_S3# SMLINK0 D VccSus3_3 VccSus3_3 CL_RST1# GPIO28 LAN_RST# VRMPWRG D RSMRST# SPI_CLK SPI_CS0# E SLP_S4# LINKALERT# / GPIO60 / CLGPIO4 VSS STP_CPU# WAKE# VSS VccSus3_3 SPI_MISO F VSS CL_DATA0 VccCL1_05 SMBCLK GPIO8 CL_CLK1 VSS TP3 INTVRMEN GPIO10 / SUS_PWR_ CL_DATA1 ACK VccSus1_05 VccSus1_5 SLP_S5# TP11 24 B SMLINK1 CL_VREF1 LAN100_SL P 23 A G SMBALERT# VccSus3_3 / GPIO11 19 GPIO24 / MEM_LED VSS RI# SYS_RESET # GPIO9 / WOL_EN ENERGY_D INTRUDER ETECT / # GPIO13 SRTCRST# CL_RST0# PWROK VSS 25 26 27 VccGLAN3_ VccGLANPL 3 L 28 29 VSS VSS A VSS B GLAN_COM GLAN_COM PO PI PERp6 / PERn6 / GLAN_RXP GLAN_RXN C SPI_MOSI PETp6 / PETn6 / VccGLAN1_ VccGLAN1_ GLAN_TXP GLAN_TXN 5 5 D VSS GLAN_CLK VccGLAN1_ VccGLAN1_ 5 5 SPI_CS1# CL_CLK0 Vcc1_5_B PETp5 VccCL1_5 VSS Vcc1_5_B VSS PERp5 PERn5 E PETn5 VSS VSS F VSS VSS PERp4 PERn4 G H VSS Vcc1_5_B Vcc1_5_B PETp4 PETn4 VSS VSS H J VSS Vcc1_5_B Vcc1_5_B VSS VSS PERp3 PERn3 J K Vcc1_5_B Vcc1_5_B Vcc1_5_B PETp3 PETn3 VSS VSS L Vcc1_05 Vcc1_05 Vcc1_05 Vcc1_5_B Vcc1_5_B Vcc1_5_B VSS VSS PERp2 PERn2 L M VSS VSS Vcc1_05 VSS Vcc1_5_B Vcc1_5_B PETp2 PETn2 VSS VSS M N VSS VSS VSS Vcc1_5_B Vcc1_5_B Vcc1_5_B VSS VSS PERp1 PERn1 N VSS K P VSS VSS Vcc1_05 R VSS VSS VSS Vcc1_5_B Vcc1_5_B PETp1 PETn1 VSS VSS P Vcc1_5_B Vcc1_5_B Vcc1_5_B Vcc1_5_B VSS VccDMIPLL R T VSS VSS Vcc1_05 VSS Vcc1_5_B DMI_CLKP DMI_CLKN Vcc1_5_B Vcc1_5_B Vcc1_5_B T U VSS VSS Vcc1_05 Vcc1_5_B Vcc1_5_B Vcc1_5_B VSS VSS DMI0TXP DMI0TXN U V Vcc1_05 Vcc1_05 Vcc1_05 VSS Vcc1_5_B Vcc1_5_B DMI0RXP DMI0RXN VSS VSS V W VccDMI Vcc1_5_B Vcc1_5_B VSS VSS DMI1TXP DMI1TXN W Y VccDMI Vcc1_5_B Vcc1_5_B DMI1RXP DMI1RXN VSS VSS Y AA VSS Vcc1_5_B Vcc1_5_B VSS VSS DMI2TXP DMI2TXN AA V_CPU_IO Vcc1_5_B Vcc1_5_B DMI2RXP DMI2RXN VSS VSS AB Vcc1_5_A Vcc3_3 Vcc1_5_A VSS V_CPU_IO Vcc1_5_B Vcc1_5_B VSS VSS DMI3TXP DMI3TXN AC VSS CPUPWRGD VSS Vcc1_5_B Vcc1_5_B DMI3RXP DMI3RXN VSS VSS AD Vcc1_5_B Vcc1_5_B AE AB AC Vcc1_5_A VSS Vcc1_5_A AD Vcc1_5_A VSS VSS Vcc3_3 SATA5GP / GPIO37 AE VSS VSS GPIO17 SLOAD / GPIO38 VSS SATA4GP / GPIO36 INIT# DPSLP# VSS Vcc1_5_B Vcc1_5_B Vcc1_5_B AF VSS SATA0TXN VSS SATA1GP / GPIO19 Vcc3_3 SDATAOUT 1 / GPIO48 VSS NMI SMI# IGNNE# VSS VSS AG VSS SATA0TXP VSS GPIO1 VSS GPIO7 SDATAOUT 0 / GPIO39 VSS Vcc3_3 INTR THRMTRIP # TP12 VSS Vcc3_3 AG AH SATA0RXP VSS SATA_CLKN VSS TP8 GPIO6 VSS SATA0GP / GPIO21 GPIO49 VSS VSS STPCLK# VSS VSS AH AJ SATA0RXN VSS SATA_CLKP VccSATAPL L TP9 TP10 SCLOCK / GPIO22 THRM# MCH_SYNC# DPRSTP# FERR# A20M# VSS VSS AJ 16 17 18 19 20 21 22 23 24 25 26 27 28 29 274 DMI_IRCO DMI_ZCOM MP P Intel® I/O Controller Hub 9 (ICH9) Family Datasheet AF Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # Ball Name A20GATE N7 A20M# AJ27 AD0 AD1 AD2 Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball # Ball Name CL_CLK1 B19 FWH3 / LAD3 K2 CL_DATA0 F22 FWH4 / LFRAME# K3 D11 CL_DATA1 C19 GLAN_CLK E25 C8 CL_RST0# F21 GLAN_COMPI B28 D9 CL_RST1# D18 GLAN_COMPO B27 AD3 E12 CL_VREF0 C25 AD4 E9 CL_VREF1 A19 GNT0# G4 AD5 C9 CLK14 H1 GNT1# / GPIO51 A7 AD6 E10 CLK48 AF3 GNT2# / GPIO53 F12 AD7 B7 CLKRUN# L4 GNT3# / GPIO55 F6 AD8 C7 CLPWROK R6 GPIO1 AG19 AD9 C5 CPUPWRGD AD22 GPIO6 AH21 AD10 G11 DEVSEL# C6 GPIO7 AG21 AD11 F8 DMI_CLKN T26 GPIO8 A21 AD12 F11 DMI_CLKP T25 GPIO9 / WOL_EN C20 AD13 E7 DMI_IRCOMP AF28 AD14 A3 DMI_ZCOMP AF29 GPIO10 / SUS_PWR_ACK C18 AD15 D2 DMI0RXN V27 GPIO12 C12 V26 GPIO13 C21 GPIO14 / AC_PRESENT C11 AD16 F10 DMI0RXP AD17 D5 DMI0TXN U29 AD18 D10 DMI0TXP U28 AD19 B3 DMI1RXN Y27 AD20 F7 DMI1RXP Y26 AD21 C3 DMITXN W29 AD22 F3 DMI1TXP W28 AD23 F4 DMI2RXN AB27 AD24 C1 DMI2RXP AB26 AD25 G7 DMI2TXN AA29 AD26 H7 DMI2TXP AA28 AD27 D1 DMI3RXN AD27 AD28 G5 DMI3RXP AD26 AD29 H6 DMI3TXN AC29 AD30 G1 DMI3TXP AC28 AD31 H3 BATLOW# B13 DPRSLPVR / GPIO16 M2 C/BE0# D8 DPRSTP# AJ25 C/BE1# B4 DPSLP# AE23 C/BE2# D6 FERR# AJ26 C/BE3# A5 FRAME# D7 CK_PWRGD R5 FWH0 / LAD0 K5 F24 FWH1 / LAD1 K4 FWH2 / LAD2 L6 CL_CLK0 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ball # GPIO17 AE18 GPIO18 K1 GPIO20 AF8 GPIO24 / MEM_LED A16 GPIO27 A9 GPIO28 D19 GPIO49 AH24 GPIO56 B10 GPIO57 / CLGPIO5 A8 HDA_BIT_CLK AF6 HDA_DOCK_EN# / GPIO33 AG7 HDA_DOCK_RST# / GPIO34 AE8 HDA_RST# AE7 HDA_SDIN0 AF4 HDA_SDIN1 AG4 HDA_SDIN2 AH3 HDA_SDIN3 AE5 HDA_SDOUT AG5 HDA_SYNC AH4 275 Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # IGNNE# AF25 PERp1 N28 RTCX2 C24 INIT# AE22 PERp2 L28 INTR AG25 PERp3 J28 S4_STATE# / GPIO26 C10 INTRUDER# C22 PERp4 G28 SATA_CLKN AH18 E28 SATA_CLKP AJ18 C28 SATA0GP / GPIO21 AH23 AJ16 AH16 INTVRMEN IRDY# B22 D3 PERp5 PERp6 / GLAN_RXP LAN_RST# D20 PERR# E4 SATA0RXN LAN_RSTSYNC C13 PETn1 P27 SATA0RXP M27 SATA0TXN AF17 AG17 LAN_RXD0 F14 PETn2 LAN_RXD1 G13 PETn3 K27 SATA0TXP LAN_RXD2 D14 PETn4 H27 SATA1GP / GPIO19 AF19 LAN_TXD0 D13 PETn5 F27 SATA1RXN AH13 D27 SATA1RXP AJ13 AG14 AF14 LAN_TXD1 D12 PETn6 / GLAN_TXN LAN_TXD2 E13 PETp1 P26 SATA1TXN LAN100_SLP A22 PETp2 M26 SATA1TXP LDRQ0# J3 PETp3 K26 SATA4GP / GPIO36 AE21 PETp4 H26 SATA4RXN AH11 PETp5 F26 SATA4RXP AJ11 PETp6 / GLAN_TXP D26 SATA4TXN AG12 PIRQA# J5 SATA4TXP AF12 AD20 LDRQ1# / GPIO23 J1 LINKALERT# / GPIO60 / CLGPIO4 E17 MCH_SYNC# AJ24 NMI AF23 PIRQB# E1 SATA5GP / GPIO37 OC0# / GPIO59 N4 PIRQC# J6 SATA5RXN AH9 OC1# / GPIO40 N5 PIRQD# C4 SATA5RXP AJ9 OC2# / GPIO41 N6 PIRQE# / GPIO2 H4 SATA5TXN AE10 OC3# / GPIO42 P6 K6 SATA5TXP AF10 OC4# / GPIO43 M1 PIRQG# / GPIO4 F2 OC5# / GPIO29 N2 L1 PIRQH# / GPIO5 G2 SATACLKREQ# / GPIO35 OC6# / GPIO30 M4 PLOCK# C2 SATALED# AG8 PLTRST# C14 SATARBIAS AH7 SATARBIAS# AJ7 SCLOCK / GPIO22 AJ22 SDATAOUT0 / GPIO39 AG22 OC7# / GPIO31 276 Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) M3 PIRQF# / GPIO3 OC8# / GPIO44 N3 PME# R2 OC9# / GPIO45 N1 PMSYNC# / GPIO0 M6 OC10# / GPIO46 P5 PWRBTN# R3 OC11# / GPIO47 P3 PWROK G20 PAR E3 RCIN# L3 AF21 PCICLK D4 SDATAOUT1 / GPIO48 REQ0# F1 PCIRST# R1 SERIRQ M5 REQ1# / GPIO50 B6 PERn1 N29 SERR# J4 REQ2# / GPIO52 F13 PERn2 L29 SLOAD / GPIO38 AE19 REQ3# / GPIO54 E6 PERn3 J29 SLP_M# B16 RI# F19 PERn4 G29 SLP_S3# C16 RSMRST# D22 PERn5 E29 SLP_S4# E16 RTCRST# A25 PERn6 / GLAN_RXN C29 SLP_S5# G17 RTCX1 C23 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # SMBALERT# / GPIO11 A17 SMBCLK G16 SMBDATA A13 SMI# Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # Ball Name Ball # USBP5P AA2 Vcc1_05 V14 USBP6N W5 Vcc1_05 V16 USBP6P W4 Vcc1_05 V17 USBP7N Y3 Vcc1_05 V18 AF24 USBP7P Y2 Vcc1_5_A AA7 SMLINK0 C17 USBP8N W1 Vcc1_5_A AB6 SMLINK1 B18 USBP8P W2 Vcc1_5_A AB7 SPI_CLK D23 USBP9N V2 Vcc1_5_A AC11 SPI_CS0# D24 USBP9P V3 Vcc1_5_A AC12 SPI_CS1# F23 USBP10N U5 Vcc1_5_A AC13 SPI_MISO E23 USBP10P U4 Vcc1_5_A AC14 SPI_MOSI D25 USBP11N U1 Vcc1_5_A AC16 SPKR M7 USBP11P U2 Vcc1_5_A AC18 SRTCRST# F20 USBRBIAS AG2 Vcc1_5_A AC19 STOP# A4 USBRBIAS# AG1 Vcc1_5_A AC21 STP_CPU# E19 V_CPU_IO AB23 Vcc1_5_A AC6 STP_PCI# A14 V_CPU_IO AC23 Vcc1_5_A AC7 STPCLK# AH27 V5REF A6 Vcc1_5_A AC9 SUS_STAT# / LPCPD R4 V5REF_Sus AE1 Vcc1_5_A AD11 SUSCLK P1 Vcc1_05 A15 Vcc1_5_A AD15 SYS_RESET# G19 Vcc1_05 B15 Vcc1_5_A AD16 Vcc1_05 C15 Vcc1_5_A AE11 Vcc1_05 D15 Vcc1_5_A AE15 Vcc1_05 E15 Vcc1_5_A AF11 Vcc1_05 F15 Vcc1_5_A AF15 Vcc1_05 L11 Vcc1_5_A AG10 Vcc1_05 L12 Vcc1_5_A AG11 Vcc1_05 L14 Vcc1_5_A AG15 Vcc1_05 L16 Vcc1_5_A AH10 Vcc1_05 L17 Vcc1_5_A AH15 Vcc1_05 L18 Vcc1_5_A AJ10 Vcc1_05 M11 Vcc1_5_A AJ15 Vcc1_05 M18 Vcc1_5_A G10 Vcc1_05 P11 Vcc1_5_A G9 Vcc1_05 P18 Vcc1_5_B AA24 Vcc1_05 T11 Vcc1_5_B AA25 Vcc1_05 T18 Vcc1_5_B AB24 Vcc1_05 U11 Vcc1_5_B AB25 Vcc1_05 U18 Vcc1_5_B AC24 Vcc1_05 V11 Vcc1_5_B AC25 Vcc1_05 V12 Vcc1_5_B AD24 THRM# AJ23 THRMTRIP# AG26 TP3 B21 TP8 AH20 TP9 AJ20 TP10 AJ21 TP11 A20 TP12 AG27 TRDY# F5 USBP0N AC5 USBP0P AC4 USBP1N AD3 USBP1P AD2 USBP2N AC1 USBP2P AC2 USBP3N AA5 USBP3P AA4 USBP4N AB2 USBP4P AB3 USBP5N AA1 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 277 Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name 278 Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball # Ball Name Ball # Ball Name Ball # Vcc1_5_B AD25 Vcc3_3 AC10 VccSus3_3 E22 Vcc1_5_B AE25 Vcc3_3 AC20 VccSus3_3 T1 Vcc1_5_B AE26 Vcc3_3 AD19 VccSus3_3 T2 Vcc1_5_B AE27 Vcc3_3 AF20 VccSus3_3 T3 Vcc1_5_B AE28 Vcc3_3 AG24 VccSus3_3 T4 Vcc1_5_B AE29 Vcc3_3 AG29 VccSus3_3 T5 Vcc1_5_B F25 Vcc3_3 AJ6 VccSus3_3 T6 Vcc1_5_B G25 Vcc3_3 B9 VccSus3_3 T7 Vcc1_5_B H24 Vcc3_3 F9 VccSus3_3 U6 Vcc1_5_B H25 Vcc3_3 G3 VccSus3_3 U7 Vcc1_5_B J24 Vcc3_3 G6 VccSus3_3 V6 Vcc1_5_B J25 Vcc3_3 J2 VccSus3_3 V7 Vcc1_5_B K23 Vcc3_3 J7 VccSus3_3 W6 Vcc1_5_B K24 Vcc3_3 K7 VccSus3_3 W7 Vcc1_5_B K25 VccCL1_05 G22 VccSus3_3 Y6 Vcc1_5_B L23 VccCL1_5 G23 VccSus3_3 Y7 Vcc1_5_B L24 VccCL3_3 A24 VccSusHDA AJ3 Vcc1_5_B L25 VccCL3_3 B24 VccUSBPLL AJ5 Vcc1_5_B M24 VccDMI W23 VRMPWRGD D21 Vcc1_5_B M25 VccDMI Y23 Vss AA3 Vcc1_5_B N23 VccDMIPLL R29 Vss AA6 Vcc1_5_B N24 VccGLAN1_5 D28 Vss AA23 Vcc1_5_B N25 VccGLAN1_5 D29 Vss AA26 Vcc1_5_B P24 VccGLAN1_5 E26 Vss AA27 Vcc1_5_B P25 VccGLAN1_5 E27 Vss AB1 Vcc1_5_B R24 VccGLAN3_3 A26 Vss AB4 Vcc1_5_B R25 VccGLANPLL A27 Vss AB5 Vcc1_5_B R26 VccHDA AJ4 Vss AB28 Vcc1_5_B R27 VccLAN1_05 A10 Vss AB29 Vcc1_5_B T24 VccLAN1_05 A11 Vss AC3 Vcc1_5_B T27 VccLAN3_3 A12 Vss AC17 Vcc1_5_B T28 VccLAN3_3 B12 Vss AC22 Vcc1_5_B T29 VccRTC A23 Vss AC26 Vcc1_5_B U23 VccSATAPLL AJ19 Vss AC27 Vcc1_5_B U24 VccSus1_05 AC8 Vss AD1 Vcc1_5_B U25 VccSus1_05 F17 Vss AD4 Vcc1_5_B V24 VccSus1_5 AD8 Vss AD5 Vcc1_5_B V25 VccSus1_5 F18 Vss AD6 Vcc1_5_B W24 VccSus3_3 A18 Vss AD7 Vcc1_5_B W25 VccSus3_3 AF1 Vss AD9 Vcc1_5_B Y24 VccSus3_3 D16 Vss AD10 Vcc1_5_B Y25 VccSus3_3 D17 Vss AD12 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # Ball Name Ball # Ball Name Ball # Vss AD13 Vss AH5 Vss E11 Vss AD14 Vss AH6 Vss E14 Vss AD17 Vss AH8 Vss E18 Vss AD18 Vss AH12 Vss E21 Vss AD21 Vss AH14 Vss E24 Vss AD23 Vss AH17 Vss F16 Vss AD28 Vss AH19 Vss F28 Vss AD29 Vss AH22 Vss F29 Vss AE2 Vss AH25 Vss G8 Vss AE3 Vss AH26 Vss G12 Vss AE4 Vss AH28 Vss G14 Vss AE6 Vss AH29 Vss G18 Vss AE9 Vss AJ1 Vss G21 Vss AE12 Vss AJ2 Vss G24 Vss AE13 Vss AJ8 Vss G26 Vss AE14 Vss AJ12 Vss G27 Vss AE16 Vss AJ14 Vss H2 Vss AE17 Vss AJ17 Vss H5 Vss AE20 Vss AJ28 Vss H23 Vss AE24 Vss AJ29 Vss H28 Vss AF2 Vss A1 Vss H29 Vss AF5 Vss A2 Vss J23 Vss AF7 Vss A28 Vss J26 Vss AF9 Vss A29 Vss J27 Vss AF13 Vss B1 Vss K28 Vss AF16 Vss B2 Vss K29 Vss AF18 Vss B5 Vss L2 Vss AF22 Vss B8 Vss L5 Vss AF26 Vss B11 Vss L7 Vss AF27 Vss B14 Vss L13 Vss AG3 Vss B17 Vss L15 Vss AG6 Vss B20 Vss L26 Vss AG9 Vss B23 Vss L27 Vss AG13 Vss B25 Vss M12 Vss AG16 Vss B26 Vss M13 Vss AG18 Vss B29 Vss M14 Vss AG20 Vss C26 Vss M15 Vss AG23 Vss C27 Vss M16 Vss AG28 Vss E2 Vss M17 Vss AH1 Vss E5 Vss M23 Vss AH2 Vss E8 Vss M28 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 279 Ballout Definition Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) 280 Table 6-2. Intel® ICH9M and ICH9M-E Ballout by Signal Name (Mobile Only) Ball Name Ball # Ball Name Ball # Vss M29 Vss U14 Vss N11 Vss U15 Vss N12 Vss U16 Vss N13 Vss U17 Vss N14 Vss U26 Vss N15 Vss U27 Vss N16 Vss V1 Vss N17 Vss V4 Vss N18 Vss V5 Vss N26 Vss V13 Vss N27 Vss V15 Vss P2 Vss V23 Vss P4 Vss V28 Vss P7 Vss V29 Vss P12 Vss W3 Vss P13 Vss W26 Vss P14 Vss W27 Vss P15 Vss Y1 Vss P16 Vss Y4 Vss P17 Vss Y5 Vss P23 Vss Y28 Vss P28 Vss Y29 Vss P29 WAKE# E20 Vss R11 Vss R12 Vss R13 Vss R14 Vss R15 Vss R16 Vss R17 Vss R18 Vss R28 Vss T12 Vss T13 Vss T14 Vss T15 Vss T16 Vss T17 Vss T23 Vss U3 Vss U12 Vss U13 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition 6.3 Intel® ICH9M-SFF Ballout (Mobile Only) This section contains the ICH9 Mobile Small Form Factor (ICH9M-SFF) ballout. Figure 6-5 and Figure 6-6 show the ballout from the top of the package view. Table 6-3 is BGA ball list, sorted alphabetically by signal name. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 281 Ballout Definition Figure 6-5. 1 Intel® ICH9M SFF Preliminary Ballout(Top view–Left Side) 2 3 4 5 6 7 8 9 10 11 12 13 AD2 AD0 AD5 LAN_TXD2 A A VSS TRDY# AD12 AD10 C/BE1# STOP# DEVSEL# AD4 REQ1# / GP50 B PAR AD25 AD17 VSS PCICLK AD19 VSS FRAME# AD8 VSS REQ2# / GP52 AD1 VSS B C AD27 AD15 IRDY# AD26 PLOCK# GNT3# / GP55 PIRQD# AD14 C/BE3# GNT2# / GP53 AD7 AD3 LAN_TXD1 C D AD28 VSS AD21 PERR# AD20 REQ3# / GP54 AD16 AD9 AD13 C/BE0# AD18 LAN_RXD1 LAN_TXD0 D E GNT0# AD29 AD23 AD24 VSS C/BE2# VSS AD11 VSS AD6 VSS GNT1# / GP51 VSS E F PIRQA# PIRQC# GPIO4 / PIRQG# AD22 PIRQB# G GPIO3 / PIRQF# VSS GPIO2 / PIRQE# REQ0# VSS V5REF Vcc3_3 Vcc1_5_A VSS VccLAN1_05 VccLAN3_3 H LDRQ0# AD31 LAD0 GPIO5 / PIRQH# SERR# Vcc3_3 Vcc3_3 Vcc1_5_A VSS VccLAN1_05 J LDRQ1# / GP23 LFRAME# LAD1 AD30 VSS VccSus3_3 VccSus3_3 VSS VSS VSS F VSS G VSS VccLAN3_3 H VSS VSS J K CLK14 VSS GPIO18 SPKR LAD2 VccSus3_3 VccSus3_3 VSS VSS VSS VSS VSS K L RCIN# PMSYNC# / GPIO0 LAD3 SERIRQ VSS VccSus3_3 VccSus3_3 VSS VSS Vcc1_05 Vcc1_05 Vcc1_05 L M DPRSLPVR / GP16 OC7# / GPIO31 OC6# / GPIO30 SATACLKRE Q# / GP35 CLKRUN# / GP32 VccSus3_3 VccSus3_3 VSS VSS Vcc1_05 VSS VSS M N OC2# / GPIO41 VSS A20GATE OC1# / GPIO40 VSS VccSus3_3 VccSus3_3 VSS VSS Vcc1_05 VSS VSS N P OC4# / GPIO43 OC5# / GPIO29 OC8# / GPIO44 OC0# / GPIO59 OC3# / GPIO42 VccSus3_3 VccSus3_3 VSS VSS Vcc1_05 VSS VSS P R OC9# / GPIO45 OC11# / GPIO47 SUSCLK OC10# / GPIO46 VSS VSS VSS VSS VSS Vcc1_05 Vcc1_05 Vcc1_05 R T PME# VSS PCIRST# CL_PWROK SUS_STAT# /LPCPD# VccSus1_05 VSS Vcc1_5_A VSS VSS VSS VSS T U CK_PWRGD USBP10P USBP10N PWRBTN# VSS Vcc1_5_A VSS Vcc1_5_A Vcc1_5_A Vcc1_5_A U V USBP8N USBP8P VSS USBP11N USBP11P VccSus1_5 VSS VSS VccSusHDA Vcc1_5_A Vcc1_5_A Vcc1_5_A V W VSS USBP7N USBP7P VSS VSS VSS VCCSUS3_3 VSS VCC1_5_A VSS Vcc1_5_A Vcc1_5_A W V5REF_SUS VCCUSBPLL Y USBP6N USBP6P VSS USBP9P USBP9N AA VSS USBP5P USBP5N VSS HDA_SDIN3 VSS HDA_RST# VSS Vcc3_3 SATA5TXP VSS SATA4TXP VSS AA AB USBP4P USBP4N VSS USBP3P CLK48 HDA_SDIN0 HDA_SYNC GPIO34 / HAD_DOCK _RST# VSS SATA5TXN VSS SATA4TXN VSS AB AC VSS USBP2N USBP2P VSS USBP3N AD USBP0P VSS USBP1N USBP1P AE VSS USBP0N VSS VSS 1 2 3 4 282 USBRBIASN Y HDA_SDIN2 HDA_SDOUT VSS USBRBIASP HDA_SDIN1 5 6 GPIO20 SATALED# VSS SATA5RXN VSS SATA1RXP AC VccHDA GPIO33 / HDA_DOCK _EN# VSS SATARBIAS# SATA5RXP SATA4RXN SATA1RXN AD HDA_BIT_CL K VSS Vcc3_3 SATARBIAS VSS SATA4RXP VSS AE 7 8 9 10 11 12 13 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Figure 6-6. Intel® ICH9M-SFF Preliminary Ballout(Top view–Right Side) 14 15 16 A LAN_RXD0 GPIO14 / AC_PRESENT GPIO57 / CLGPIO5 17 CL_VREF1 B LAN_RXD2 STPPCI# / GP15 VSS C GPIO12 / LAN_PHY_PWR _CTRL SMBDATA D LAN_RSTSYNC E GPIO26 / S4_STATE# 18 19 20 21 22 23 24 25 CL_CLK1 TP11 STPCPU# / GP25 PLTRST# GPIO24 / MEM_LED SMBALERT# / GP11 SMLINK1 VSS A CL_ST1# CL_DATA1 VSS SLP_S4# LINKALERT# / GPIO60 / CLGPIO4 VSS SLP_M# VRMPWRGD GPIO8 B BATLOW# CL_RST0# SMBCLK TP3 RI# WAKE# CL_CLK0 INTRUDER# SRTCRST# SYS_RESET# C GPIO56 / GBEDOCK# SLP_S5# GPIO27 SLP_S3# RSMRST# GPIO13 GPIO9 / WOL_EN LAN_RST# PWROK VSS LAN100_SLP D VSS GPIO10 / SUS_PWR_A CK VSS SMLINK0 VSS GPIO28 VSS CL_DATA0 SPI_CS0# SPI_CLK INTVRMEN E CL_VREF0 SPI_MOSI GPIO58 / SPI_CS1# / CLGPIO6 VSS RTCX1 F VSS GLAN_CLK SPI_MISO RTCRST# RTCX2 G VSS PERn6/ GLAN_RXn PERp6/ GLAN_RXp H PETp6/ GLAN_TXp PETn6/ GLAN_TXn VSS J K F G VCCSUS3_3 VCCSUS3_3 VSS VccRTC VccCL1_05 VSS H VCCSUS3_3 VccSus1_05 VccSus1_5 VccCL1_5 VSS VccGLAN1_5 J VccCL3_3 VSS VSS VccGLANPLL VccGLAN1_5 Vcc1_5_B VSS VSS K VccCL3_3 VSS VccGLAN3_3 VSS Vcc1_5_B Vcc1_5_B PETn5 PETp5 VSS PERn5 PERp5 L Vcc1_05 Vcc1_05 VSS VSS Vcc1_5_B Vcc1_5_B VSS VSS PETp4 PETn4 VSS L M VSS Vcc1_05 VSS VSS Vcc1_5_B Vcc1_5_B PETn3 PETp3 VSS PERp4 PERn4 M N VSS Vcc1_05 VSS VSS Vcc1_5_B Vcc1_5_B VSS VSS PERn3 PERp3 VSS N P VSS Vcc1_05 VSS VSS Vcc1_5_B VccDMIPLL PETn2 PETp2 VSS PERp2 PERn2 P R Vcc1_05 Vcc1_05 VSS VSS Vcc1_5_B VSS VSS VSS PETp1 PETn1 VSS R GLAN_COMPO GLAN_COMPI T VSS VSS VSS VccDMI Vcc1_5_B Vcc1_5_B DMI_CLKN DMI_CLKP VSS PERp1 PERn1 T U VSS Vcc1_5_A V_CPU_IO VccDMI Vcc1_5_B Vcc1_5_B VSS VSS DMI0TXP DMI0TXN VSS U V VCC3_3 Vcc1_5_A V_CPU_IO VSS Vcc3_3 VSS DMI1TXN DMI1TXP VSS DMI0RXP DMI0RXN V W VCC3_3 VSS VSS VccSATAPLL Vcc1_5_A VSS VSS VSS DMI1RXN DMI1RXP VSS W DMI2TXN DMI2TXP VSS DMI2RXN DMI2RXP Y VSS VSS DMI3TXN DMI3TXP VSS AA DMI_ZCOMP DMI_IRCOMP A20M# DMI3RXN DMI3RXP AB SMI# TP11 THRMTRIP# VSS STPCLK# AC Y AA SATA1TXN VSS VSS VSS GPIO19 / SATA1GP AB SATA1TXP VSS SATA_CLKP TP8 GPIO38 / SLOAD AC VSS SATA0TXN SATA_CLKN TP9 GPIO39 / SDATAOUT0 AD SATA0RXP SATA0TXP VSS TP10 GPIO7 VSS THRM# NMI VSS IGNNE# INTR FERR# AD AE SATA0RXN VSS GPIO1 / TACH1 GPIO17 GPIO6 GPIO21 / SATA0GP GPIO36 / SATA4GP INIT# CPUPWRGD DPRSTP# DPSLP# VSS AE 14 15 16 17 18 19 20 21 22 23 24 25 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet VSS GPIO37 / SATA5GP GPIO48 / MCH_SYNC# SDATAOUT1 GPIO22 / SCLOCK GPIO49 283 Ballout Definition Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Names A20GATE Ball Names Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Ball Names Ball N3 CL_DATA0 E22 GNT1# / GPIO51 E12 AB23 CL_DATA1 B18 GNT2# / GPIO53 C10 AD0 A11 CL_PWROK T4 GNT3# / GPIO55 AD1 B12 CL_RST0# C17 GPIO1 / TACH1 AE16 GPIO10 / SUS_PWR_ACK E16 GPIO12 / LAN_PHY_PWR_CTRL C14 GPIO13 D20 GPIO14 / AC_PRESENT A15 A20M# AD10 A4 CL_ST1# B17 AD11 E8 CL_VREF0 F21 AD12 A3 CL_VREF1 A17 AD13 D9 CLK14 K1 AD14 C8 CLK48 AB5 AD15 C2 CLKRUN# / GPIO32 AD16 D7 CPUPWRGD AE22 AD17 B3 TP11 AC22 AD18 D11 DEVSEL# A7 AD19 B6 DMI_CLKN T21 AD2 A10 DMI_CLKP T22 AD20 D5 DMI_IRCOMP AB22 AD21 D3 DMI_ZCOMP AB21 AD22 F4 DMI0RXN V25 AD23 E3 DMI0RXP V24 AD24 E4 DMI0TXN AD25 B2 AD26 C4 AD27 M5 C6 GPIO17 AE17 GPIO18 K3 GPIO19 / SATA1GP AA18 GPIO2 / PIRQE# G3 GPIO20 AC8 GPIO21 / SATA0GP AE19 GPIO22 / SCLOCK AC19 GPIO24 / MEM_LED A22 U24 GPIO26 / S4_STATE# E14 DMI0TXP U23 GPIO27 D17 DMI1RXN W23 GPIO28 E20 C1 DMI1RXP W24 GPIO3 / PIRQF# G1 AD28 D1 DMI1TXN V21 AD29 E2 DMI1TXP V22 GPIO33 / HDA_DOCK_EN# AD8 C12 DMI2RXN Y24 AB8 AD30 J4 DMI2RXP Y25 GPIO34 / HDA_DOCK_RST# AD31 H2 DMI2TXN Y21 AD4 A8 DMI2TXP Y22 AD5 A12 DMI3RXN AB24 AD6 E10 DMI3RXP AB25 AD7 C11 DMI3TXN AA23 AD8 B9 DMI3TXP AA24 AD9 D8 DPRSLPVR / GPIO16 BATLOW# C16 DPRSTP# C/BE0# D10 DPSLP# C/BE1# A5 FERR# C/BE2# E6 FRAME# C/BE3# C9 GLAN_CLK G22 GPIO6 AE18 CK_PWRGD U1 GLAN_COMPI H22 GPIO7 AD18 CL_CLK0 C22 GLAN_COMPO H21 GPIO8 B25 CL_CLK1 A18 GNT0# AD3 284 Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) GPIO36 / SATA4GP AE20 GPIO37 / SATA5GP AA20 GPIO38 / SLOAD AB18 GPIO39 / SDATAOUT0 AC18 GPIO4 / PIRQG# F3 GPIO48 / SDATAOUT1 AB19 AE23 GPIO49 AC20 AE24 GPIO5 / PIRQH# AD25 GPIO56 D15 GPIO57 / CLGPIO5 A16 M1 B8 H4 E1 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Names Ball Names GPIO9 / WOL_EN D21 OC5# / GPIO29 P2 PWRBTN# HDA_BIT_CLK AE7 OC6# / GPIO30 M3 PWROK HDA_RST# AA7 OC7# / GPIO31 M2 RCIN# L1 HDA_SDIN0 AB6 OC8# / GPIO44 P3 REQ0# G4 HDA_SDIN1 AE6 OC9# / GPIO45 R1 REQ1# / GPIO50 A9 HDA_SDIN2 AC6 PAR B1 REQ2# / GPIO52 B11 HDA_SDIN3 AA5 PCICLK B5 REQ3# / GPIO54 D6 HDA_SDOUT AC7 PCIRST# T3 RI# C20 HDA_SYNC Ball Names Ball U4 D23 AB7 PERn1 T25 RSMRST# D19 AD23 PERn2 P25 RTCRST# G24 INIT# AE21 PERn3 N23 RTCX1 F25 INTR AD24 PERn4 M25 RTCX2 G25 INTRUDER# C23 PERn5 K24 SATA_CLKN AC16 INTVRMEN E25 PERn6/GLAN_RXn H24 SATA_CLKP AB16 IRDY# C3 PERp1 T24 SATA0RXN AE14 LAD0 H3 PERp2 P24 SATA0RXP AD14 LAD1 J3 PERp3 N24 SATA0TXN AC15 LAD2 K5 PERp4 M24 SATA0TXP AD15 L3 IGNNE# LAD3 PERp5 K25 SATA1RXN AD13 LAN_RST# D22 PERp6/GLAN_RXp H25 SATA1RXP AC13 LAN_RSTSYNC D14 PERR# D4 SATA1TXN AA14 LAN_RXD0 A14 PETn1 R24 SATA1TXP AB14 LAN_RXD1 D12 PETn2 P21 SATA4RXN AD12 LAN_RXD2 B14 PETn3 M21 SATA4RXP AE12 LAN_TXD0 D13 PETn4 L24 SATA4TXN AB12 LAN_TXD1 C13 PETn5 K21 SATA4TXP AA12 LAN_TXD2 A13 PETn6/GLAN_TXn J24 SATA5RXN AC11 LAN100_SLP D25 PETp1 R23 SATA5RXP AD11 LDRQ0# H1 PETp2 P22 SATA5TXN AB10 LDRQ1# / GPIO23 J1 PETp3 M22 SATA5TXP AA10 LFRAME# J2 PETp4 L23 PETp5 K22 SATACLKREQ# / GPIO35 M4 PETp6/GLAN_TXp J23 SATALED# AC9 PIRQA# F1 SATARBIAS AE10 AD10 LINKALERT# / GPIO60 / CLGPIO4 B21 MCH_SYNC# AB20 NMI AD21 PIRQB# F5 SATARBIAS# OC0# / GPIO59 P4 PIRQC# F2 SERIRQ L4 OC1# / GPIO40 N4 PIRQD# C7 SERR# H5 OC10# / GPIO46 R4 PLOCK# C5 SLP_M# B23 OC11# / GPIO47 R2 PLTRST# A21 SLP_S3# D18 OC2# / GPIO41 N1 PME# T1 SLP_S4# B20 OC3# / GPIO42 P5 L2 SLP_S5# D16 OC4# / GPIO43 P1 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PMSYNC# / GPIO0 285 Ballout Definition Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Names Ball SMBALERT# / GPIO11 A23 SMBCLK SMBDATA Names Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Ball Names Ball USBP4P AB1 Vcc1_5_A G9 USBP5N AA3 Vcc1_5_A H9 C18 USBP5P AA2 Vcc1_5_A U11 Y1 Vcc1_5_A V11 C15 USBP6N AC21 USBP6P Y2 Vcc1_5_A T9 SMLINK0 E18 USBP7N W2 Vcc1_5_A U9 SMLINK1 A24 USBP7P W3 VCC1_5_A W10 SPI_CLK E24 USBP8N V1 Vcc1_5_B J19 SPI_CS0# E23 USBP8P V2 Vcc1_5_B K18 SPI_CS1# F23 USBP9N Y5 Vcc1_5_B K19 SPI_MISO G23 USBP9P Y4 Vcc1_5_B L18 SPI_MOSI F22 USBRBIASN AD5 Vcc1_5_B L19 SPKR K4 SMI# SRTCRST# STOP# STPCLK# USBRBIASP AE5 Vcc1_5_B M18 C24 V_CPU_IO U16 Vcc1_5_B M19 A6 V_CPU_IO V16 Vcc1_5_B N18 V5REF G7 Vcc1_5_B N19 AC25 STPCPU# / GPIO25 A20 V5REF_SUS U7 Vcc1_5_B P18 STPPCI# / GPIO15 B15 Vcc1_05 L11 Vcc1_5_B R18 SUS_STAT#/LPCPD# T5 Vcc1_05 L12 Vcc1_5_B T18 SUSCLK R3 Vcc1_05 L13 Vcc1_5_B T19 C25 Vcc1_05 L14 Vcc1_5_B U18 THRM# AD20 Vcc1_05 L15 Vcc1_5_B U19 THRMTRIP# AC23 Vcc1_05 M11 Vcc3_3 V18 TP10 AD17 Vcc1_05 M15 Vcc3_3 AE9 TP11 A19 Vcc1_05 N11 Vcc3_3 AA9 TP3 C19 Vcc1_05 N15 Vcc3_3 G8 TP8 AB17 Vcc1_05 P11 Vcc3_3 H7 TP9 AC17 Vcc1_05 P15 Vcc3_3 H8 TRDY# A2 Vcc1_05 R11 VCC3_3 V14 USBP0N AE2 Vcc1_05 R12 VCC3_3 W14 USBP0P AD1 Vcc1_05 R13 VCCSATAPLL W17 USBP10N U3 Vcc1_05 R14 VccCL1_05 G18 USBP10P U2 Vcc1_05 R15 VccCL1_5 H17 USBP11N V4 Vcc1_5_A U13 VccCL3_3 J14 USBP11P V5 Vcc1_5_A V13 VccCL3_3 K14 USBP1N AD3 Vcc1_5_A W13 VccDMI T17 USBP1P AD4 Vcc1_5_A U12 VccDMI U17 USBP2N AC2 Vcc1_5_A V12 VccDMIPLL P19 USBP2P AC3 Vcc1_5_A W12 VccGLAN1_5 H19 USBP3N AC5 Vcc1_5_A U15 VccGLAN3_3 K16 USBP3P AB4 Vcc1_5_A V15 VccGLANPLL J17 USBP4N AB2 Vcc1_5_A W18 VccHDA AD7 SYS_RESET# 286 Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Ballout Definition Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Names Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Ball Names Ball Names Ball VccGLAN1_5 J18 VSS E11 VSS L17 VccLAN1_05 G11 VSS E13 VSS L21 VccLAN1_05 H11 VSS E15 VSS L22 VccLAN3_3 G12 VSS E17 VSS L25 VccLAN3_3 H13 VSS E19 VSS M9 VccRTC G17 VSS E21 VSS M10 VccSus1_05 T7 VSS F24 VSS M12 VccSus1_05 H15 VSS G2 VSS M13 VccSus1_5 H16 VSS G5 VSS M14 VccSus1_5 V7 VSS G10 VSS M16 VCCSUS3_3 W8 VSS G13 VSS M17 VCCSUS3_3 G14 VSS G16 VSS M23 VCCSUS3_3 G15 VSS G19 VSS N2 VCCSUS3_3 H14 VSS G21 VSS N5 VccSus3_3 J7 VSS H10 VSS N9 VccSus3_3 J8 VSS H12 VSS N10 VccSus3_3 K7 VSS H18 VSS N12 VccSus3_3 K8 VSS H23 VSS N13 VccSus3_3 L7 VSS J5 VSS N14 VccSus3_3 L8 VSS J9 VSS N16 VccSus3_3 M7 VSS J10 VSS N17 VccSus3_3 M8 VSS J11 VSS N21 VccSus3_3 N7 VSS J12 VSS N22 VccSus3_3 N8 VSS J13 VSS N25 VccSus3_3 P7 VSS J15 VSS P9 VccSus3_3 P8 VSS J21 VSS P10 VccSusHDA V10 VSS J22 VSS P12 VCCUSBPLL U8 VSS J25 VSS P13 VRMPWRGD B24 VSS K2 VSS P14 B4 VSS K9 VSS P16 VSS B7 VSS K10 VSS P17 VSS B10 VSS K11 VSS P23 VSS B13 VSS K12 VSS R5 VSS B16 VSS K13 VSS R7 VSS B19 VSS K15 VSS R8 VSS B22 VSS K17 VSS R9 VSS D2 VSS K23 VSS R10 VSS D24 VSS L5 VSS R16 VSS E5 VSS L9 VSS R17 VSS E7 VSS L10 VSS R19 VSS E9 VSS L16 VSS R21 VSS Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 287 Ballout Definition Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) 288 Table 6-3. Intel® ICH9M-SFF Ballout by Signal Name - (Mobile Only) Names Ball Names VSS R22 VSS AA15 VSS R25 VSS AA16 VSS T2 VSS AA17 VSS T8 VSS AA19 VSS T10 VSS AA21 VSS T11 VSS AA22 VSS T12 VSS AA25 VSS T13 VSS AB3 VSS T14 VSS AB9 VSS T15 VSS AB11 VSS T16 VSS AB13 VSS T23 VSS AB15 VSS U5 VSS AC1 VSS U10 VSS AC4 VSS U14 VSS AC10 VSS U21 VSS AC12 VSS U22 VSS AC14 VSS U25 VSS AC24 VSS V3 VSS AD2 VSS V8 VSS AD6 VSS V19 VSS AD9 VSS V23 VSS AD16 VSS W1 VSS AD19 VSS W4 VSS AD22 VSS W5 VSS AE4 VSS W7 VSS AE11 VSS W9 VSS AE13 VSS W11 VSS AE15 VSS W15 VSS AE3 VSS W16 VSS A1 VSS W19 VSS A25 VSS W21 VSS AE1 VSS W22 VSS AE25 VSS W25 VSS V17 VSS Y3 VSS AE8 VSS Y23 VSS V9 VSS AA1 VSS J16 VSS AA4 WAKE# C21 VSS AA6 VSS AA8 VSS AA11 VSS AA13 Ball §§ Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Package Information 7 Package Information 7.1 Intel® ICH9 Package (Desktop Only) The ICH9 package information is shown in Figure 7-1, Figure 7-2, and Figure 7-3. Note: All dimensions, unless otherwise specified, are in millimeters Figure 7-1. Intel® ICH9 Package (Top View) -A// 0.127 A -B- PIN #1 I.D (SHINY) 1.0 DIA X 0.15 DEPTH 9.0 X 9.0 FROM CENTER LINE 22.10 REF 0.127 A 4 X 45° TOP VIEW Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 289 Package Information Figure 7-2. Intel® ICH9 Package (Bottom View) Figure 7-3. Intel® ICH9 Package (Side View) // 0.15 0.20 C -C- 3 SEATING PLANE SIDE VIEW 290 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Package Information 7.2 Intel® ICH9 Mobile Package (Mobile Only) 7.2.1 Intel® 82801IBM ICH9M and 82801IEM ICH9M-E Package The ICH9M package information is shown in Figure 7-4, Figure 7-5, and Figure 7-6. Note: All dimensions unless otherwise specified are in millimeters Figure 7-4. Intel® ICH9M Package (Top View) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 291 Package Information Figure 7-5. Intel® ICH9M Package (Bottom View) Figure 7-6. Intel® ICH9M Package (Side View) // 0.15 0.20 C -C- 3 SEATING PLANE SIDE VIEW 292 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Package Information 7.2.2 Intel® ICH9M-SSF Package Figure 7-7. Intel® ICH9M-SSF Package Drawing §§ Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 293 Package Information 294 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics 8 Electrical Characteristics This chapter contains the DC and AC characteristics for the ICH9. AC timing diagrams are included 8.1 Thermal Specifications Refer to the Intel® I/O Controller Hub (ICH9) Thermal Design Guidelines document for ICH9 thermal information. 8.2 Absolute Maximum Ratings Table 8-1. Intel® ICH9 Absolute Maximum Ratings Parameter Maximum Limits Voltage on any 3.3 V Pin with respect to Ground -0.5 to Vcc3_3 + 0.5 V Voltage on any 5 V Tolerant Pin with respect to Ground (V5REF = 5 V) -0.5 to V5REF + 0.5 V 1.05 V Supply Voltage with respect to VSS -0.5 to 2.1 V 1.25 V Supply Voltage with respect to VSS -0.5V to 2.1V 1.5 V Supply Voltage with respect to VSS -0.5 to 2.1 V 3.3 V Supply Voltage with respect to VSS -0.5 to 4.6 V 5.0 V Supply Voltage with respect to VSS -0.5 to 5.5 V V_CPU_IO Supply Voltage with respect to VSS -0.5 to 2.1 V 8.3 DC Characteristics Table 8-2. DC Current Characteristics1 (Desktop Only) Power Plane Symbol Maximum Power Consumption S0 S3 S4/S5 G3 V5REF 2 mA N/A N/A N/A V5REF_Sus 2 mA 1 mA 1 mA N/A Vcc3_3 308 mA N/A N/A N/A VccSus3_3 212 mA 53 mA 53 mA N/A VccHDA6 32mA N/A N/A N/A VccSusHDA6 32 mA 1 mA 1 mA N/A VccGLAN3_3 1 mA N/A N/A N/A VccGLAN1_5 80 mA N/A N/A N/A VccLAN3_35 19 mA 78 mA 78 mA N/A Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 295 Electrical Characteristics Table 8-2. DC Current Characteristics1 (Desktop Only) Power Plane Maximum Power Consumption Symbol S0 S3 S4/S5 G3 VccLAN1_052, 5 Powered by Vcc1_05 in S0 Powered by VccLAN3_3 in S3 Powered by VccLAN3_3 in S4/ S5 N/A VccCL3_3 19 mA 73 mA 73 mA N/A VccCL1_52 Powered by Vcc1_5_A in S0 Powered by VccCL3_3 in S3 Powered by VccCL3_3 in S4/S5 N/A Powered by Vcc1_05 in S0 Powered by VccCL3_3 in S3 Powered by VccCL3_3 in S4/S5 N/A Vcc1_5_A 1.644 A N/A N/A N/A Vcc1_5_B 646 mA N/A N/A N/A Powered by Vcc1_5_A in S0 Powered by VccSus3_3 in S3 Powered by VccSus3_3 in S4/S5 N/A 1.634 A N/A N/A N/A Powered by Vcc1_05 in S0 Powered by VccSus3_3 in S3 Powered by VccSus3_3 in S4/S5 N/A N/A N/A N/A 6 μA 50 mA N/A N/A N/A 2 mA N/A N/A N/A VccGLANPLL 23 mA N/A N/A N/A VccUSBPLL VccCL1_052 VccSus1_52 Vcc1_05 VccSus1_052 VccRTC3, 4 VccDMI 7 V_CPU_IO 11 mA N/A N/A N/A 7 VccDMIPLL 23 mA N/A N/A N/A VccSATAPLL 47 mA N/A N/A N/A NOTES: 1. These are estimated DC current numbers. 2. Internal voltage regulators power these wells inside the Intel® ICH9 and current for these rails are accounted for in the sourcing voltage rail current requirements. 3. Only the G3 state of this rail is shown to provide an estimate of battery life. 4. Icc (RTC) data is taken with VccRTC at 3.0 V while the system is in a mechanical off (G3) state at room temperature. 5. The current for this rail in S3 and S4/S5 is based on the integrated LAN running at 10/100. 6. The current for this rail was measured with VccHDA and VccSusHDA set to 3.3 V. 7. The current for this rail was measured with VccDMI set to 1.5 V. 296 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-3. Preliminary DC Current Characteristics (Mobile Only)1 Power Plane Symbol Maximum Power Consumption S0 S3 S4/S5 G3 V5REF 2 mA N/A N/A N/A V5REF_Sus 2 mA 1 mA 1 mA N/A Vcc3_3 308 mA N/A N/A N/A VccSus3_3 212 mA 53 mA 53 mA N/A 11 mA N/A N/A N/A 11 mA 1 mA 1 mA N/A 6 VccHDA 6 VccSusHDA VccGLAN3_3 1 mA N/A N/A N/A VccGLAN1_5 80 mA N/A N/A N/A VccLAN3_35 19 mA 78 mA 78 mA N/A Powered by Vcc1_05 in S0 Powered by VccLAN3_3 in S3 Powered by VccLAN3_3 in S4/S5 N/A VccCL3_3 19 mA 73 mA 73 mA N/A VccCL1_52 Powered by Vcc1_5_A in S0 Powered by VccCL3_3 in S3 Powered by VccCL3_3 in S4/S5 N/A Powered by Vcc1_05 in S0 Powered by VccCL3_3 in S3 Powered by VccCL3_3 in S4/S5 N/A Vcc1_5_A 1.342 A N/A N/A N/A Vcc1_5_B 646 mA N/A N/A N/A Powered by Vcc1_5_A in S0 Powered by VccSus3_3 in S3 Powered by VccSus3_3 in S4/S5 N/A 1.634 A N/A N/A N/A Powered by Vcc1_05 in S0 Powered by VccSus3_3 in S3 Powered by VccSus3_3 in S4/S5 N/A N/A N/A N/A 6 μA 48 mA N/A N/A N/A VccLAN1_052, 5 VccCL1_052 VccSus1_52 Vcc1_05 VccSus1_052 VccRTC3, 4 VccDMI 7 V_CPU_IO 2 mA N/A N/A N/A VccGLANPLL 23 mA N/A N/A N/A VccUSBPLL 11 mA N/A N/A N/A VccDMIPLL7 23 mA N/A N/A N/A VccSATAPLL 47 mA N/A N/A N/A NOTES: 1. These are preliminary DC current numbers and are subject to change. 2. Internal voltage regulators power these wells inside the Intel® ICH9 and current for this rail is accounted for in the sourcing voltage rail current requirements. 3. Only the G3 state of this rail is shown to provide an estimate of battery life. 4. Icc (RTC) data is taken with VccRTC at 3.0 V while the system is in a mechanical off (G3) state at room temperature. 5. The current for this rail in S3 and S4/S5 is based on the integrated LAN running at 10/100. 6. The current for this rail was measured with VccHDA and VccSusHDA set to 1.5 V. 7. The current for this rail was measured with VccDMI set to 1.25 V. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 297 Electrical Characteristics Table 8-4. DC Characteristic Input Signal Association (Sheet 1 of 2) Symbol VIH1/VIL1 (5V Tolerant) VIH2/VIL2 Associated Signals PCI Signals: AD[31:0], C/BE[3:0]#, DEVSEL#, FRAME#, IRDY#, PAR, PERR#, PLOCK#, REQ[3:0]#, SERR#, STOP#, TRDY# Interrupt Signals: PIRQ[D:A]#, PIRQ[H:E]# GPIO Signals: GPIO[54, 52, 50, 5:2] Gigabit LAN Connect Signals: GLAN_RX[p,n] Clock Signals: CLK48 Power Management Signals: MCH_SYNC#, THRM#, VRMPWRGD, LAN_RST#, CLPWROK Mobile Only: CLKRUN# SATA Signals: SATAGP[5:4, 1:0] Desktop Only: SATAGP[3:2] VIH3/VIL3 Interrupt Signals: SERIRQ Processor Signals: RCIN#, A20GATE USB Signals: OC[11:0]# GPIO Signals: GPIO[59, 55, 53, 51, 49:36, 35, 31:29, 22:16, 7:6, 1, 0], Desktop Only: GPIO32 Intel® Quiet System Technology Signals: TACH[3:0] Strap Signals: GNT[3:0]#,SPKR, SATALED# (Strap purposes only) Clock Signals: CLK14, PCICLK LPC/Firmware Hub Signals: LAD[3:0]/FWH[3:0], LDRQ0#, LDRQ1# VIH4/VIL4 PCI Signals: PME# SPI Signals: SPI_MISO GPIO Signals: GPIO[33, 23] Strap Signals: SPI_MOSI, GNT0# (Strap purposes only) SMBus Signals: SMBCLK, SMBDATA, SMBALERT# VIH5/VIL5 System Management Signals: SMLINK[1:0], LINKALERT#, CLGPIO4 (Digital Office Only) GPIO Signals: GPIO[60, 11] VIH6/VIL6 LAN Signals: GLAN_CLK, LAN_RXD[2:0] VIH7/VIL7 Processor Signals: FERR#, THRMTRIP# VIMIN8/VIMAX8 PCI Express* Data RX Signals: PER[p,n][6:1] VIH9/VIL9 Real Time Clock Signals: RTCX1 VIMIN10/VIMAX10 SATA Signals: SATA[3:0]RX[P,N], Desktop Only: SATA[5:4]RX[P,N] Intel® High Definition Audio Signals: HDA_SDIN[3:0] Strap Signals: HDA_SDOUT, HDA_SYNC (Strap purposes only) VIH11/VIL11 GPIO Signals: GPIO34 NOTE: See VIL_HDA/VIH_HDA for High Definition Audio Low Voltage Mode VIH12/VIL12/ Vcross(abs) 298 Clock Signals: DMI_CLKN, DMI_CLKP, SATA_CLKN, SATA_CLKP Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-4. DC Characteristic Input Signal Association (Sheet 2 of 2) Symbol Associated Signals Power Management Signals: PWRBTN#, RI#, SYS_RESET#, WAKE# Mobile Only: BATLOW# GPIO Signals: GPIO[60, 57:56, 28:26, 24, 14:12, 10:8], VIH13/VIL13 Desktop Only: GPIO[25, 15] System Management Signals: Desktop Only: CLGPIO1, CLGPIO2, CLGPIO4 (Digital Office Only) Mobile Only: AC_PRESENT Power Management Signals: PWROK, RSMRST# VIH14/VIL14 VIH_CL/VIL_CL VIH_CL2/VIL_CL2 VDI / VCM / VSE (5V Tolerant) VHSSQ / VHSDSC / VHSCM System Management Signals: INTRUDER# Miscellaneous Signals: INTVRMEN, LAN100_SLP, RTCRST#, SRTCRST# Controller Link: CL_CLK0, CL_DATA0 Mobile Only: CL_CLK1, CL_DATA1 GPIO Signals: GPIO58 (Desktop Only) System Management Signals: CLGPIO6 (Digital Office Only USB Signals: USBP[11:0][P,N] (Low-speed and Full-speed) USB Signals: USBP[11:0][P,N] (in High-speed Mode) (5V Tolerant) Intel® High Definition Audio Signals: HDA_SDIN[3:0] VIH_HDA / VIL_HDA Strap Signals: HDA_SDOUT, HDA_SYNC (Strap purposes only) NOTE: Only applies when running in Low Voltage Mode (1.5 V) VIH_SST/VIL_SST VIH_PECI/VIL_PECI Intel® Quiet System Technology Signals: Desktop Only: SST Intel® Quiet System Technology Signals: Desktop Only: PECI NOTES: 1. VDI = | USBPx[P] – USBPx[N] 2. Includes VDI range 3. Applies to Low-Speed/High-Speed USB 4. PCI Express mVdiff p-p = 2*|PETp[x] – PETn[x]| 5. GLAN mVdiff p-p = 2* |GLAN_RXp – GLAN_RXn| 6. SATA Vdiff, RX (VIMAX10/MIN10) is measured at the SATA connector on the receiver side (generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]RXP – SATA[x]RXN| 7. VccRTC is the voltage applied to the VccRTC well of the ICH9. When the system is in a G3 state, this is generally supplied by the coin cell battery, but for S5 and greater, this is generally VccSus3_3. 8. CL_Vref = 0.27 (VccCL1_5). CL_VREF0 applies to Desktop configurations. CL_VREF1 applies to Mobile configurations. 9. Applies to Ultra DMA Modes greater than Ultra DMA Mode 4. 10. This is an AC Characteristic that represents transient values for these signals. 11. Applies to Hogh-Speed USB 2.0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 299 Electrical Characteristics Table 8-5. Symbol DC Input Characteristics (Sheet 1 of 2) Parameter Min Max Unit Notes VIL1 Input Low Voltage –0.5 0.3(3.3 V) V Note 12 VIH1 Input High Voltage 0.5(3.3 V) V5REF + 0.5 V Note 12 VIL2 Minimum Input Voltage 200 — mVdiff p-p Note 5 VIH2 Maximum Input Voltage — 1350 mVdiff p-p Note 5 VIL3 Input Low Voltage –0.5 0.8 V VIH3 Input High Voltage 2.0 3.3 V + 0.5 V Note 12 VIL4 Input Low Voltage –0.5 0.3(3.3 V) V Note 12 VIH4 Input High Voltage 0.5(3.3 V) 3.3 V + 0.5 V Note 12 VIL5 Input Low Voltage –0.5 0.8 V VIH5 Input High Voltage 2.1 3.3 V + 0.5 V Note 12 VIL6 Input Low Voltage -0.5 0.3(3.3 V) V Note 12 VIH6 Input High Voltage 0.6(3.3 V) 3.3 V + 0.5 V Note 12 VIL7 Input Low Voltage –0.5 0.58(V_CPU_IO) V VIH7 Input High Voltage 0.73(V_CPU_IO) V_CPU_IO + 0.5 V VIMIN8 Minimum Input Voltage 175 — mVdiff p-p Note 4 VIMAX8 Maximum Input Voltage — 1200 mVdiff p-p Note 4 VIL9 Input Low Voltage –0.5 0.10 V VIH9 Input High Voltage 0.40 1.2 V VIMIN10- Gen1i Minimum Input Voltage - 1.5 Gb/s internal SATA 325 — mVdiff p-p 6 VIMAX10-Gen1i Maximum Input Voltage - 1.5 Gb/s internal SATA — 600 mVdiff p-p 6 VIMIN10-Gen1m Minimum Input Voltage - 1.5 Gb/s eSATA 240 — mVdiff p-p 6 VIMAX10-Gen1m Maximum Input Voltage - 1.5 Gb/s eSATA — 600 mVdiff p-p 6 VIMIN10-Gen2i Minimum Input Voltage - 3.0 Gb/s internal SATA 275 — mVdiff p-p 6 VIMAX10-Gen2i Maximum Input Voltage - 3.0 Gb/s internal SATA — 750 mVdiff p-p 6 VIMIN10-Gen2m Minimum Input Voltage - 3.0 Gb/s eSATA 240 — mVdiff p-p 6 300 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-5. Symbol VIMAX10-Gen2m DC Input Characteristics (Sheet 2 of 2) Parameter Maximum Input Voltage - 3.0 Gb/s eSATA Min Max Unit Notes — 750 mVdiff p-p 6 VIL11 Input Low Voltage –0.5 0.35(3.3 V) V Note 12 VIH11 Input High Voltage 0.65(3.3 V) 3.3 V + 0.5 V Note 12 VIL12 Input Low Voltage -0.150 0.150 V VIH12 Input High Voltage 0.660 0.850 V VIL13 Input Low Voltage –0.5 0.8 V VIH13 Input High Voltage 2.0 3.3 V + 0.5 V VIL14 Input Low Voltage –0.5 0.78 V VIH14 Input High Voltage 2.0 VccRTC + 0.5 V Note 7 VIL_CL Input Low Voltage –0.3 (CL_VREF - 0.075) V Note 8 VIH_CL Input High Voltage (CL_VREF + 0.075) 1.2 V Note 8 VIL_CL2 Input Low Voltage –0.5 0.3(VccCL3_3) V VIH_CL2 Input High Voltage 0.5(VccCL3_3) VccCL3_3 + 0.5 V 0.250 0.550 V Vcross(abs) Absolute Crossing Point Note 12 VDI Differential Input Sensitivity 0.2 — V Note 1,3 VCM Differential Common Mode Range 0.8 2.5 V Note 2,3 VSE Single-Ended Receiver Threshold 0.8 2.0 V Note 3 VHSSQ HS Squelch Detection Threshold 100 150 mV Note 11 VHSDSC HS Disconnect Detection Threshold 525 625 mV Note 11 VHSCM HS Data Signaling Common Mode Voltage Range –50 500 mV Note 11 VIL_HDA Input Low Voltage — 0.4(VccHDA) V VIH_HDA Input High Voltage 0.6(VccHDA) — V VIL_SST Input Low Voltage -0.5 0.4 V VIH_SST Input High Voltage 1.1 Vcc + 0.5 V VIL_PECI Input Low Voltage -0.5 0.275(V_CPU_IO) V VIH_PECI Input High Voltage 0.725(V_CPU_IO) V_CPU_IO + 0.5 V NOTES: 1. VDI = | USBPx[P] – USBPx[N] 2. Includes VDI range 3. Applies to Low-Speed/Full-Speed USB 4. PCI Express mVdiff p-p = 2*|PETp[x] - PETn[x]| 5. GLAN mVdiff p-p = 2* |GLAN_RXp - GLAN_RXn| 6. SATA Vdiff, RX (VIMAX10/MIN10) is measured at the SATA connector on the receiver side (generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]RXP SATA[x]RXN| Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 301 Electrical Characteristics 7. 8. 9. 10. 11. 12. Table 8-6. VccRTC is the voltage applied to the VccRTC well of the ICH9. When the system is in a G3 state, this is generally supplied by the coin cell battery, but for S5 and greater, this is generally VccSus3_3. CL_Vref = 0.27 (VccCL1_5). CL_VREF0 applies to Desktop configurations. CL_VREF1 applies to Mobile configurations. Applies to Ultra DMA Modes greater than Ultra DMA Mode 4 This is an AC Characteristic that represents transient values for these signals Applies to Hogh-Speed USB 2.0. 3.3 V refers to VccSus3_3 for signals in the suspend well and to Vcc3_3 for signals in the core well. See Table 3-2 and Table 3-3 for signal and power well association. DC Characteristic Output Signal Association (Sheet 1 of 2) Symbol VOH1/VOL1 Associated Signals Processor Signals: A20M#, IGNNE#, INIT#, INTR, NMI, SMI#, STPCLK#, CPUPWRGD Mobile Only: DPSLP# Power Management Signals: Mobile Only: DPRSTP# PCI Signals: AD[31:0], C/BE[3:0]#, DEVSEL#, FRAME#, IRDY#, PAR, PERR#, PLOCK#, SERR#(1), STOP#, TRDY# VOH2/VOL2 Intel® High Definition Audio Signals: HDA_RST#, HDA_SDOUT, HDA_SYNC, HDA_BIT_CLK NOTE: See VOH_HDA/VOL_HDA for High Definition Audio Low Voltage Mode GPIO Signals: GPIO33 SMBus Signals: SMBCLK VOH3/VOL3 (1), SMBDATA (1) System Management Signals: SMLINK[1:0](1), LINKALERT# GPIO Signals: GPIO[60, 11] Power Management Signals: SLP_S3#, SLP_S4#, SLP_S5#, SLP_M#, SUSCLK, SUS_STAT#/LPCPD#, CK_PWRGD, S4_STATE# Mobile Only: DPRSLPVR, CLKRUN#, PMSYNC# SATA Signals: SATACLKREQ#, SATALED#, SLOAD, SDATAOUT[1:0] VOH4/VOL4 GPIO Signals: GPIO[49:48, 39:35, 32:31, 26, 21:18, 16, 7:6, 0], Desktop Only: GPIO32 Intel® High Definition Audio Signals: HDA_DOCK_EN# (Mobile Only) Other Signals: SPKR Interrupt Signals: SERIRQ VOH5/VOL5 VOMIN6/VOMAX6 VOMIN7/VOMAX7 302 USB Signals: USBP[11:0][P,N] in Low-speed and Full-speed Modes PCI Express* Data TX Signals: PET[p,n][6:1] SATA Signals: SATA[5:4, 1:0]TX[P,N], Desktop Only: SATA[3:2]TX[P,N] Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-6. DC Characteristic Output Signal Association (Sheet 2 of 2) Symbol Associated Signals LPC/Firmware Hub Signals: LAD[3:0]/FWH[3:0], LFRAME#/FWH[4], Desktop Only: INIT3_3V# Power Management Signal: PLTRST# PCI Signals: PCIRST#, GNT[3:0]#, PME#(1) Interrupt Signals: PIRQ[D:A], PIRQ[H:E]#(1) VOH8/VOL8 GPIO Signals: GPIO[58, 55:50, 34, 23:22, 17, 5:2, 1] SATA Signals: SCLOCK System Management Signals: CLGPIO6 (Digital Office Only) Intel® High Definition Audio Signals: HDA_DOCK_RST# (Mobile Only) SPI Signals: SPI_CS0#, SPI_MOSI, SPI_CLK LAN Signals: LAN_RSTSYNC, LAN_TXD[2:0] Power Management Signals: STP_CPU#, STP_PCI# GPIO Signals: GPIO[60, 59, 57:56, 47:40, 31:27, 24, 15:12, 10:8], Desktop Only: GPIO[25, 15] System Management Signals: LINKALERT#, WOL_EN, MEM_LED VOH9/VOL9 Digital Office Only (Desktop): CLGPIO1, CLGPIO2, CLGPIO04, CLGPIO5 Mobile Only: SUS_PWR_ACK Gigabit LAN Signals: LAN_PHY_PWR_CTRL Controller Link Signals: Mobile Only: CL_RST1# VOMIN10/VOMAX10 Gigabit Lan Connect Signals: GLAN_TX[p,n] VHSOI VHSOH VHSOL USB Signals: USBP[11:0][P:N] in High-speed Mode VCHIRPJ VCHIRPK VOH_HDA/VOL_HDA Intel® High Definition Audio Signals: HDA_RST#, HDA_SDOUT, HDA_SYNC NOTE: Only applies when running in Low Voltage Mode (1.5 V) VOH_PWM/ VOL_PWM VOH_CL1/VOL_CL1 VOH_CL2/VOL_CL2 Intel® Quiet System Technology PWM: Desktop Only: PWM[2:0](1) Link Controller Signals: CL_CLK0, CL_DATA0 Mobile Only: CL_CLK1, CL_DATA1 Link Controller Signals: CL_RST0# SPI Signals: SPI_CS1# VOH_CL3/VOL_CL3 VOH_SST/VOL_SST VOH_PECI/ VOL_PECI GPIO Signals: GPIO58 (Desktop Only) System Management Signals: CLGPIO6 (Digital Office Only) SST signal: Desktop Only: SST PECI signal: Desktop Only: PECI NOTE: 1. These signals are open drain. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 303 Electrical Characteristics Table 8-7. Symbol DC Output Characteristics (Sheet 1 of 2) Parameter Min Max Unit IOL / IOH Notes Note 4 VOL1 Output Low Voltage — 0.255 V 3 mA VOH1 Output High Voltage V_CPU_IO - 0.3 — V -3 mA VOL2 Output Low Voltage — 0.1(3.3 V) V 1.5 mA Note 7 VOH2 Output High Voltage 0.9(3.3 V) — V -0.5 mA Note 7 VOL3 Output Low Voltage — 0.4 V 4 mA VOH3 Output High Voltage 3.3 V - 0.5 — V -2 mA VOL4 Output Low Voltage — 0.4 V 6 mA VOH4 Output High Voltage 3.3 V - 0.5 — V -2 mA VOL5 Output Low Voltage — 0.4 V 5 mA VOH5 Output High Voltage 3.3 V – 0.5 — V -2 mA Note1 Note 7 Note 7 Note 7 VOMIN6 Minimum Output Voltage 800 — mVdif fp-p Note 2 VOMAX6 Maximum Output Voltage — 1200 mVdif fp-p Note 2 VOMIN7-Gen1i,m Minimum Output Voltage 400 — mVdif fp-p Note 3 VOMAX7-Gen1i,m Maximum Output Voltage — 600 mVdif fp-p Note 3 VOMIN7-Gen2i,m Minimum Output Voltage 400 — mVdif fp-p Note 3 VOMAX7-Gen2i,m Maximum Output Voltage — 700 mVdif fp-p Note 3 VOL8 Output Low Voltage — 0.1(3.3 V) V 1.5 mA Note 7 VOH8 Output High Voltage 0.9(3.3 V) — V -0.5 mA Note 1 Note 7 VOL9 Output Low Voltage — 0.4 V 6 mA VOH9 Output High Voltage 3.3 V - 0.5 — V -0.5 mA VOMIN10 Minimum Output Voltage 750 — mVdif fp-p Note 6 VOMAX10 Maximum Output Voltage — 1350 mVdif fp-p Note 6 –10.0 10.0 mV VHSOI HS Idle Level VHSOH HS Data Signaling High 360 440 mV VHSOL HS Data Signaling Low –10.0 10.0 mV 700 1100 mV VCHIRPJ 304 Note 7 Chirp J Level Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-7. Symbol DC Output Characteristics (Sheet 2 of 2) Parameter Min Max Unit –900 –500 mV IOL / IOH VCHIRPK Chirp K Level VOL_HDA Output Low Voltage — 0.1(VccHDA) V 1.5 mA VOH_HDA Output High Voltage 0.9(VccHDA) — V -0.5 mA VOL_PWM Output Low Voltage — 0.4 V 5 mA VOH_PWM Output High Voltage — — VOL_CL1 Output Low Voltage — 0.15 V VOH_CL1 Output High Voltage 0.485(VccCL1_5) — V VOL_CL2 Output Low Voltage — 0.1(VccCL1_5) V 1.5 mA VOH_CL2 Output High Voltage 0.9(VccCL1_5) — V -1.5 mA VOL_CL3 Output Low Voltage — 0.4 V 6 mA VOH_CL3 Output High Voltage VccCL3_3 -0.5 — V -0.5 mA VOL_SST Output Low Voltage — 0.3 V 0.5 mA VOH_SST Output High Voltage 1.1 — V -6 mA VOL_PECI Output Low Voltage — 0.25(V_CPU_IO) V 0.5 mA VOH_PECI Output High Voltage 0.75(V_CPU_IO) — Notes Note 1 1 mA -6 mA NOTES: 1. The SERR#, PIRQ[H:A], SMBDATA, SMBCLK, LINKALERT#, SMLINK[1:0], and PWM[2:0] signal has an open drain driver and SATALED# has an open collector driver, and the VOH spec does not apply. This signal must have external pull up resistor. 2. PCI Express mVdiff p-p = 2*|PETp[x] – PETn[x]| 3. SATA Vdiff, tx (VOMIN7/VOMAX7) is measured at the SATA connector on the transmit side (generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]TXP – SATA[x]TXN| 4. Maximum Iol for CPUPWRGD is 12mA for short durations (<500 mS per 1.5 s) and 9 mA for long durations. 5. For INIT3_3V only, for low current devices, the following applies: VOL5 Max is 0.15 V at an IOL5 of 2 mA. 6. GLAN mVdiff p-p = 2*|GLAN_TXp – GLAN_TXn| 7. 3.3 V refers to VccSus3_3 for signals in the suspend well and to Vcc3_3 for signals in the core well. See Table 3-2 and Table 3-3 for signal and power well association. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 305 Electrical Characteristics Table 8-8. Other DC Characteristics (Sheet 1 of 2) Symbol V_CPU_IO Parameter Processor I/F Min Nom Max Unit Notes 0.945 — 1.3 V 1 V5REF ICH9 Core Well Reference Voltage 4.75 5 5.25 V 1 CL_VREF Controller Link Reference Voltage 0.385 0.405 0.425 V 1 I/O Buffer Voltage 3.135 3.3 3.465 V 1 Internal Logic and I/O Buffer Voltage 1.425 1.5 1.575 V 1 Vcc3_3 Vcc1_5_A, Vcc1_5_B, VccUSBPLL, VccSATAPLL, VccDMIPLL VccGLANPLL V5REF_Sus Suspend Well Reference Voltage 4.75 5 5.25 V 1 VccSus3_3 Suspend Well I/O Buffer Voltage 3.135 3.3 3.465 V 1 Vcc1_05 Internal Logic Voltage 0.998 1.05 1.102 V 1 VccHDA High Definition Audio Controller Core Voltage 3.135 3.3 3.465 V 1 VccHDA (low voltage 1.5 V) High Definition Audio Controller Low Voltage Mode Core Voltage 1.425 1.5 1.575 V 1 Vcc_DMI (Mobile Only) DMI Buffer Voltage 0.998 1.05 1.102 V Vcc_DMI (Desktop Only) DMI Buffer Voltage 1.188 1.25 1.312 V Vcc_DMI (ESI Mode Only) DMI Buffer Voltage 1.425 1.5 1.575 V LAN Controller I/O Buffer Voltage 3.135 3.3 3.465 V 1 VccGLAN1_5 Gigabit Lan Transmitter and Receiver Voltage 1.425 1.5 1.575 V 1 VccGLAN3_3 Gigabit Lan Internal Logic and I/O Buffer Voltage 3.135 3.3 3.465 V 1 Controller Link Buffer Voltage 3.135 — 3.465 V 1 VccLAN3_3 VccCL3_3 VccRTC (G3-S0) VccSusHDA VccSusHDA (low voltage) 306 2 — 3.465 V 1 High Definition Audio Controller Suspend Voltage Battery Voltage 3.135 3.3 3.465 V 1 High Definition Audio Controller Low Voltage Mode Suspend Voltage 1.425 1.5 1.575 V 1 VDI Differential Input Sensitivity 0.2 — — V |(USBPx+,USB Px–)| VCM Differential Common Mode Range 0.8 — 2.5 V Includes VDI VCRS Output Signal Crossover Voltage 1.3 — 2.0 V VSE Single Ended Rcvr Threshold 0.8 — 2.0 V ILI1 ATA Input Leakage Current –200 — 200 µA (0 V < VIN < 5V) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-8. Other DC Characteristics (Sheet 2 of 2) Symbol Parameter Min Nom Max Unit Notes ILI2 PCI_3V Hi-Z State Data Line Leakage –10 — 10 µA (0 V < VIN < Vcc3_3) ILI3 PCI_5V Hi-Z State Data Line Leakage –70 — 70 µA Max VIN = 2.7 V Min VIN = 0.5 V ILI4 Input Leakage Current – Clock signals –100 — +100 µA 2 ILI5 Input Leakage Current – SPI signals -10 — +10 µA CIN Input Capacitance – All Other — — 12 pF FC = 1 MHz COUT Output Capacitance — — 12 pF FC = 1 MHz CI/O I/O Capacitance — — 12 pF FC = 1 MHz Typical Value CL XTAL1 6 pF CL XTAL2 6 pF NOTES: 1. The I/O buffer supply voltage is measured at the ICH package pins. The tolerances shown in Table 9-8 are inclusive of all noise from DC up to 20 MHz. In testing, the voltage rails should be measured with a bandwidth limited oscilloscope that has a rolloff of 3 dB/decade above 20 MHz. 2. Includes CLK14, CLK48, GLAN_CLK and PCICLK Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 307 Electrical Characteristics 8.4 AC Characteristics 1 Table 8-9. Clock Timings (Sheet 1 of 2) Sym Parameter Min Max Unit Notes Figure PCI Clock (PCICLK) t1 Period 30 33.3 ns 8-1 t2 High Time 12 — ns 8-1 t3 Low Time 12 — ns 8-1 t4 Rise Time — 3 ns 8-1 t5 Fall Time — 3 ns 8-1 14 MHz Clock (CLK14) t6 Period 67 70 ns 8-1 t7 High Time 20 — ns 8-1 t8 Low Time 20 — ns 8-1 t41 Rising Edge Rate 1.0 4.0 V/ns 5 t42 Falling Edge Rate 1.0 4.0 V/ns 5 1 48 MHz Clock (CLK48) fclk48 Operating Frequency 48.000 — MHz t9 Frequency Tolerance — 100 ppm High Time 7 — ns 8-1 t10 t11 Low Time 7 — ns 8-1 t12 Rise Time — 1.2 ns 8-1 t13 Fall Time — 1.2 ns 8-1 SMBus Clock (SMBCLK) fsmb Operating Frequency 10 100 KHz t18 High time 4.0 50 μs t19 Low time 4.7 — μs 8-10 t20 Rise time — 1000 ns 8-10 t21 Fall time — 300 ns 8-10 HDA_BIT_CLK fHDA (Intel® 2 8-10 High Definition Audio) Operating Frequency 24.0 MHz Frequency Tolerance — 100 ppm t26a Input Jitter (refer to Clock Chip Specification) — 300 ppm t27a High Time (Measured at 0.75 Vcc) 18.75 22.91 ns 8-1 t28a Low Time (Measured at 0.35 Vcc) 18.75 22.91 ns 8-1 SATA Clock (SATA_CLKP, SATA_CLKN) / DMI Clock (DMI_CLKP, DMI_CLKN) t36 308 Period 9.997 10.0533 ns Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-9. Clock Timings (Sheet 2 of 2) Sym tsatasl Parameter Min Max 2.5 8 Slew rate Unit Notes V/ns 7 kHz 4 Figure Suspend Clock (SUSCLK) fsusclk Operating Frequency 32 t39 High Time 10 — μs 4 t39a Low Time 10 — μs 4 MHz 6 Gigabit Internet Clock (GLAN_CLK) tglanclk Operating Fequency 5 62.5 tglanhi High Time 6.4 — ns tglanlo Low Time 6.4 — ns tglansl Slew rate 1.0 4 V/ns Intel® Quiet System Technology fpwm PWM Operating Frequency 10 28,000 Hz NOTES: 1. The CLK48 expects a 40/60% duty cycle. 2. The maximum high time (t18 Max) provide a simple ensured method for devices to detect bus idle conditions. 3. BITCLK Rise and Fall times are measured from 10%VDD and 90%VDD. 4. SUSCLK duty cycle can range from 30% minimum to 70% maximum. 5. CLK14 edge rates in a system as measured from 0.8 V to 2.0 V. 6. The active frequency can be 5 MHz, 50 MHz or 62.5 MHz depending on the interface speed. Dynamic changes of the normal operating frequency are not allowed. 7. See CK505 Clock Synthesizer Specification for measurement procedure. Table 8-10. PCI Interface Timing Sym Parameter Min Max Units Notes Figure 2 11 ns 1 8-2 t40 AD[31:0] Valid Delay t41 AD[31:0] Setup Time to PCICLK Rising 7 — ns 8-3 t42 AD[31:0] Hold Time from PCICLK Rising 0 — ns 8-3 t43 C/BE[3:0]#, FRAME#, TRDY#, IRDY#, STOP#, PAR, PERR#, PLOCK#, DEVSEL# Valid Delay from PCICLK Rising 2 11 ns t44 C/BE[3:0]#, FRAME#, TRDY#, IRDY#, STOP#, PAR, PERR#, PLOCK#, IDSEL, DEVSEL# Output Enable Delay from PCICLK Rising 2 t45 C/BE[3:0]#, FRAME#, TRDY#, IRDY#, STOP#, PERR#, PLOCK#, DEVSEL#, GNT[A:B]# Float Delay from PCICLK Rising 2 t46 C/BE[3:0]#, FRAME#, TRDY#, IRDY#, STOP#, SERR#, PERR#, DEVSEL#, Setup Time to PCICLK Rising 7 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 28 1 8-2 ns 8-6 ns 8-4 ns 8-3 309 Electrical Characteristics Table 8-10. PCI Interface Timing Sym Parameter Min Max Units Notes Figure t47 C/BE[3:0]#, FRAME#, TRDY#, IRDY#, STOP#, SERR#, PERR#, DEVSEL#, REQ[A:B]# Hold Time from PCLKIN Rising 0 — ns 8-3 t48 PCIRST# Low Pulse Width 1 ms 8-5 t49 GNT[3:0]# Valid Delay from PCICLK Rising 2 12 ns t50 REQ[3:0]# Setup Time to PCICLK Rising 12 — ns NOTE: 1. Refer to note 3 of table 4-4 in Section 4.2.2.2 and note 2 of table 4-6 in Section 4.2.3.2 of the PCI Local Bus Specification, Revision 2.3 for measurement details. Table 8-11. Universal Serial Bus Timing Sym Parameter Min Max Units Notes Fig Full-speed Source (Note 7) t100 USBPx+, USBPx- Driver Rise Time 4 20 ns 1, CL = 50 pF 8-7 t101 USBPx+, USBPx- Driver Fall Time 4 20 ns 1, CL = 50 pF 8-7 –3.5 –4 3.5 4 ns ns 2, 3 8-8 - For Paired Transitions t103 Source SE0 interval of EOP 160 175 ns 4 8-9 t104 Source Jitter for Differential Transition to SE0 Transition –2 5 ns 5 –18.5 –9 18.5 9 ns ns 3 8-8 4 8-9 Source Differential Driver Jitter t102 - To Next Transition Receiver Data Jitter Tolerance t105 - T o Next Transition - For Paired Transitions t106 EOP Width: Must accept as EOP 82 — ns t107 Width of SE0 interval during differential transition — 14 ns Low-speed Source (Note 8) t108 USBPx+, USBPx – Driver Rise Time 75 300 ns 1, 6 CL = 50 pF CL = 350 pF 8-7 t109 USBPx+, USBPx – Driver Fall Time 75 300 ns 1,6 CL = 50 pF CL = 350 pF 8-7 –25 –14 25 14 ns ns 2, 3 8-8 For Paired Transitions t111 Source SE0 interval of EOP 1.25 1.50 µs 4 8-9 t112 Source Jitter for Differential Transition to SE0 Transition –40 100 ns 5 Source Differential Driver Jitter t110 310 To Next Transition Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-11. Universal Serial Bus Timing Sym Parameter Min Max Units Notes Fig Full-speed Source (Note 7) t113 Receiver Data Jitter Tolerance - To Next Transition- For Paired Transitions –152 –200 152 200 ns ns 3 8-8 t114 EOP Width: Must accept as EOP 670 — ns 4 8-9 t115 Width of SE0 interval during differential transition — 210 ns NOTES: 1. Driver output resistance under steady state drive is spec’d at 28 ohms at minimum and 43 ohms at maximum. 2. Timing difference between the differential data signals. 3. Measured at crossover point of differential data signals. 4. Measured at 50% swing point of data signals. 5. Measured from last crossover point to 50% swing point of data line at leading edge of EOP. 6. Measured from 10% to 90% of the data signal. 7. Full-speed Data Rate has minimum of 11.97 Mb/s and maximum of 12.03 Mb/s. 8. Low-speed Data Rate has a minimum of 1.48 Mb/s and a maximum of 1.52 Mb/s. Table 8-12. SATA Interface Timings Sym Parameter Min Max Units Notes UI Gen I Operating Data Period 666.43 670.23 ps UI-2 Gen II Operating Data Period (3Gb/s) 333.21 335.11 ps t120 Rise Time 0.15 0.41 UI 1 t121 Fall Time 0.15 0.41 UI 2 t122 TX differential skew — 20 ps t123 COMRESET 310.4 329.6 ns 3 t124 COMWAKE transmit spacing 103.5 109.9 ns 3 t125 OOB Operating Data period 646.67 686.67 ns 4 Figure NOTES: 1. 20% – 80% at transmitter 2. 80% – 20% at transmitter 3. As measured from 100 mV differential crosspoints of last and first edges of burst. 4. Operating data period during Out-Of-Band burst transmissions. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 311 Electrical Characteristics Table 8-13. SMBus Timing Sym Parameter Min Max Units Notes Fig t130 Bus Tree Time Between Stop and Start Condition 4.7 — µs 8-10 t131 Hold Time after (repeated) Start Condition. After this period, the first clock is generated. 4.0 — µs 8-10 t132 Repeated Start Condition Setup Time 4.7 — µs 8-10 t133 Stop Condition Setup Time 4.0 — µs 8-10 t134 Data Hold Time 0 — ns 4 8-10 t135 Data Setup Time 250 — ns t136 Device Time Out 25 35 ms 1 8-10 t137 Cumulative Clock Low Extend Time (slave device) — 25 ms 2 8-11 t138 Cumulative Clock Low Extend Time (master device) — 10 ms 3 8-11 NOTES: 1. A device will timeout when any clock low exceeds this value. 2. t137 is the cumulative time a slave device is allowed to extend the clock cycles in one message from the initial start to stop. If a slave device exceeds this time, it is expected to release both its clock and data lines and reset itself. 3. t138 is the cumulative time a master device is allowed to extend its clock cycles within each byte of a message as defined from start-to-ack, ack-to-ack or ack-to-stop. 4. t134 has a minimum timing for I2C of 0 ns, while the minimum timing for SMBus is 300 ns. Table 8-14. Intel® High Definition Audio Timing 312 Sym Parameter Min Max Units Notes Fig t143 Time duration for which HDA_SDOUT is valid before HDA_BIT_CLK edge. 7 — ns 8-13 t144 Time duration for which HDA_SDOUT is valid after HDA_BIT_CLK edge. 7 — ns 8-13 t145 Setup time for HDA_SDIN[3:0] at rising edge of HDA_BIT_CLK 15 — ns 8-13 t146 Hold time for HDA_SDIN[3:0] at rising edge of HDA_BIT_CLK 0 — ns 8-13 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-15. LPC Timing Sym Parameter Min Max Units Notes Fig 11 ns 8-2 ns 8-6 t150 LAD[3:0] Valid Delay from PCICLK Rising 2 t151 LAD[3:0] Output Enable Delay from PCICLK Rising 2 t152 LAD[3:0] Float Delay from PCICLK Rising — 28 ns 8-4 t153 LAD[3:0] Setup Time to PCICLK Rising 7 — ns 8-3 t154 LAD[3:0] Hold Time from PCICLK Rising 0 — ns 8-3 t155 LDRQ[1:0]# Setup Time to PCICLK Rising 12 — ns 8-3 t156 LDRQ[1:0]# Hold Time from PCICLK Rising 0 — ns 8-3 t157 LFRAME# Valid Delay from PCICLK Rising 2 12 ns 8-2 Min Max Units Table 8-16. Miscellaneous Timings Sym Parameter Notes Fig t160 SERIRQ Setup Time to PCICLK Rising 7 — ns 8-3 t161 SERIRQ Hold Time from PCICLK Rising 0 — ns 8-3 t162 RI#, EXTSMI#, GPIO, USB Resume Pulse Width 2 — RTCCLK 8-5 t163 SPKR Valid Delay from OSC Rising — 200 ns 8-2 t164 SERR# Active to NMI Active — 200 ns t165 IGNNE# Inactive from FERR# Inactive — 230 ns 1 Table 8-17. SPI Timings (20 MHz) Sym Parameter Min Max Units Notes 17.2 18.4 MHz 1 40% 60% Fig t180 Serial Clock Frequency - 20MHz Operation t182 SPI Clock Duty cycle at the host t183 Tco of SPI_MOSI with respect to serial clock falling edge at the host -5 13 ns 8-12 t184 Setup of SPI_MISO with respect to serial clock falling edge at the host 16 — ns 8-12 t185 Hold of SPI_MISO with respect to serial clock falling edge at the host 0 — ns 8-12 t186 Setup of SPI_CS[1:0]# assertion with respect to serial clock rising at the host 30 — ns 8-12 t187 Hold of SPI_CS[1:0]# deassertion with respect to serial clock falling at the host 30 — ns 8-12 8-12 NOTE: 1. The typical clock frequency driven by the ICH9 is 17.86 MHz. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 313 Electrical Characteristics Table 8-18. SPI Timings (33 MHz) Sym Parameter Min Max Units Notes MHz 1 Fig t180b Serial Clock Frequency - 33MHz Operation 30.3 32.19 t182b SPI Clock Duty cycle at the host 48% 52% t183b Tco of SPI_MOSI with respect to serial clock falling edge at the host -5 5 ns 8-12 t184b Setup of SPI_MISO with respect to serial clock falling edge at the host 8 — ns 8-12 t185b Hold of SPI_MISO with respect to serial clock falling edge at the host 0 — ns 8-12 t186b Setup of SPI_CS[1:0]# assertion with respect to serial clock rising at the host 30 — ns 8-12 t187b Hold of SPI_CS[1:0]# deassertion with respect to serial clock falling at the host 30 — ns 8-12 8-12 NOTE: 1. The typical clock frequency driven by the ICH9 is 31.25 MHz. Table 8-19. SST Timings Sym tBIT Parameter Min Max Units Bit time (overall time evident on SST) 0.495 500 µs Bit time driven by an originator 0.495 250 µs tBIT,jitter Bit time jitter between adjacent bits in an SST message header or data bytes after timing has been negotiated — — % tBIT,drift Change in bit time across a SST address or SST message bits as driven by the originator. This limit only applies across tBIT-A bit drift and tBIT-M drift. — — % tH1 High level time for logic '1' 0.6 0.8 x tBIT tH0 High level time for logic '0' 0.2 0.4 x tBIT tSSTR Rise time (measured from VOL = 0.3V to VIH,min) — 25 + 5 ns/ node tSSTF Fall time (measured from VOH = 1.1V to VIL,max) — 33 ns/ node Notes 1 Fig - 2 NOTES: 1. The originator must drive a more restrictive time to allow for quantized sampling errors by a client yet still attain the minimum time less than 500 µs. tBIT limits apply equally to tBIT-A and tBIT-M. ICH9 is targeted on 1 Mbps which is 1 µs bit time. 2. The minimum and maximum bit times are relative to tBIT defined in the Timing Negotiation pulse. 314 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-20. PECI Timings Sym tBIT Parameter Bit time (overall time evident on PECI) Bit time driven by an originator Min Max Units 0.495 500 µs 0.495 250 µs tBIT,jitter Bit time jitter between adjacent bits in an PECI message header or data bytes after timing has been negotiated — — % tBIT,drift Change in bit time across a PECI address or PECI message bits as driven by the originator. This limit only applies across tBIT-A bit drift and tBIT-M drift. — — % Notes Fig 1 tH1 High level time for logic '1' 0.6 0.8 x tBIT tH0 High level time for logic '0' 0.2 0.4 x tBIT 2 tPECIR Rise time (measured from VOL to VIH,min, Vtt(nom) -5%) — 30 + 5 ns/ node 3 tPECIF Fall time (measured from VOH to VIL,max, Vtt(nom) +5%) — 30 ns/ node 3 NOTES: 1. The originator must drive a more restrictive time to allow for quantized sampling errors by a client yet still attain the minimum time less than 500 µs. tBIT limits apply equally to tBIT-A and tBIT-M. ICH9 is targeted on 2 MHz which is 500 ns bit time. 2. The minimum and maximum bit times are relative to tBIT defined in the Timing Negotiation pulse. 3. Extended trace lengths may appear as additional nodes. Table 8-21. Power Sequencing and Reset Signal Timings (Sheet 1 of 2) Sym Parameter Min Max Units 18 — ms Notes Fig 8-14 8-15 t200 VccRTC active to RTCRST# inactive t201 V5REF_Sus active to VccSus3_3 active 0 — ms 1 8-14 8-15 t202 VccSus3_3 active to VccSus1_05 active — — – 2 8-14 8-15 t203 VccRTC supply active to VccSus supplies active 0 — ms 3 8-14 8-15 t204 VccSus supplies active to LAN_RST# inactive, RSMRST# inactive 10 — ms t205 VccSus3_3 active to VccSus1_5 active — — — 9 t206 VccLAN3_3 active to VccLAN1_05 active — — — 6 t207 VccCL3_3 active to VccCL1_05 active — — ms 7 t208 VccCL3_3 active to VccCL1_5 active — — ms 8 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 8-14 8-15 315 Electrical Characteristics Table 8-21. Power Sequencing and Reset Signal Timings (Sheet 2 of 2) Sym Parameter Min Max Units Notes Fig t209 V5REF active to Vcc3_3 active 0 — ms 1 8-14 t211 Vcc1_5 active to V_CPU_IO active — — – 4 8-14 t212 VRMPWRGD active to PWROK active 3 — ms t213 VccSus supplies active to Vcc supplies active 0 — ms 8-15 8-17 8-18 3 Vcc supplies active to PWROK t214 Note: PWROK assertion indicates that PCICLK has been stable for at least 1 ms. t217 PWROK and VRMPWRGD active to SUS_STAT# inactive and Processor interface signals latched to strap value t218 SUS_STAT# inactive to PLTRST# inactive t219 99 — ms 33 71 RTCCLK 8-14 8-14 8-15 8-17 8-18 5, 10, 12 8-15 8-17 8-18 8-20 8-15 8-17 8-18 8-20 2 3 RTCCLK 10 PLTRST# assertion to VccGLANPLL inactive for platforms using ICH9 integrated GbE LAN 200 — μs 11 t228 HDA_RST# active low pulse width 1 — μs t229 HDA_RST# inactive to HDA_BIT_CLK startup delay 162.8 — ns NOTES: 1. V5REF must be powered up before Vcc3_3, or after Vcc3_3 within 0.7 V. Also, V5REF must power down after Vcc3_3, or before Vcc3_3 within 0.7 V. 2. The associated 3.3 V and 1.05 V supplies are assumed to power up or down ‘together’. 3. The VccSus supplies must never be active while the VccRTC supply is inactive. 4. Vcc1_5 must power up before V_CPU_IO or after V_CPU_IO within 0.7 V, b) V_CPU_IO must power down before Vcc1_5 or after Vcc1_5 within 0.7 V. 5. INIT# value determined by value of the CPU BISTEnable bit (Chipset Configuration Register Offset 3414h: bit 2). 6. The associated 3.3 V and 1.05 V supplies are assumed to power up or down ‘together’. 7. The associated 3.3 V and 1.05 V supplies are assumed to power up or down ‘together’. 8. The associated 3.3 V and 1.5 V supplies are assumed to power up or down ‘together’. 9. The associated 3.3 V and 1.5 V supplies are assumed to power up or down ‘together’. 10. These transitions are clocked off the internal RTC. 1 RTC clock is approximately from 28.992 µs to 32.044 µs 11. “VccGLANPLL inactive" is defined for this timing to be when VccGLANPLL drops to 1.425 V or less, as measured at the ICH9. This timing applies only to platforms using ICH9 integrated GbE LAN. 12. Maximum timing may be exceeded in a management engine enabled system. 316 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics . Table 8-22. Power Management Timings (Sheet 1 of 3) Sym Min Max Units VccSus active to SLP_S5#, SLP_S4#, SLP_S3#, SUS_STAT#, PLTRST# and PCIRST#active — 50 ns t232 RSMRST# inactive to SUSCLK running, SLP_S5# inactive — 110 ms t233 SLP_S5# inactive to SLP_S4# inactive t230 t231 Parameter t234 SLP_S4# inactive to SLP_S3# inactive t250 Processor I/F signals latched prior to STPCLK# active See Note Below 1 Note 16 RTCCLK 0 — 3.36 — µs Notes 8-15 6, 22 8-15 8 8-15 8-23 1 8-15 8-17 8-18 8-23 8-24 9 8-19 8-21 8-22 8-22 3, 11 8-20 8-21 8-22 (Mobile Only) t251 Bus Master Idle to DPSLP# active (Mobile Only) Fig t252 DMI message to PMSYNC# assertion (Mobile Only) 0 — PCICLK t253 DPSLP# active to STP_CPU# active (Mobile Only) 1 1 PCICLK 3 8-20 8-21 8-22 0 — PCICLK 3, 10 8-21 8-22 0 — 1.5 1.8 t254 STP_CPU# active to processor clock stopped 8-22 (Mobile Only) t255 STP_CPU# active to DPRSTP#, DPRSLPVR active 8-21 8-22 (Mobile Only) t265 Break Event to DPRSTP#, DPRSLPVR inactive (C4 Exit) (Mobile Only) µs 12 8-21 8-22 t266a DPRSLPVR, DPRSTP# inactive to STP_CPU# inactive and CPU Vcc ramped (Mobile Only) Programable. See D31:F0:AA, bits 3:2 µs 8-21 t266b DPRSLPVR, DPRSTP# inactive to STP_CPU# inactive and CPU Vcc ramped (Mobile Only) Programable. See D31:F0:A8 bits 2:0 µs 8-22 Break Event to STP_CPU# inactive t267 (C3 Exit) 6 Note 14 PCICLK 3, 13, 14 8-20 0 3 PCICLK 3, 10 8-21 8-22 (Mobile Only) t268 STP_CPU# inactive to processor clock running (Mobile Only) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 317 Electrical Characteristics Table 8-22. Power Management Timings (Sheet 2 of 3) Sym t269 t270 Parameter STP_CPU# inactive to DPSLP# inactive (Mobile Only) DPSLP# inactive to STPCLK# inactive (Mobile Only) Min Max Units Notes Fig 1 1 PCICLK 3, 7 8-20 8-21 8-22 0 µs 8-20 8-21 8-22 0 ns 8-19 Break Event to STPCLK# inactive t273 (C2 Exit) (Mobile Only) t274 STPCLK# inactive to processor I/F signals unlatched 8 9 PCICLK 3, 9 (Mobile Only) t275 PMSYNC# de-assert to STPCLK# deassert. (Mobile Only) Programable. See D31:F0:A8 8-19 8-21 8-22 µs 8-22 PCICLK 2 8-16 8-17 8-18 8-22 PCICLK 3 8-16 RTCCLK 1 8-17 8-18 bits 5:3 t280 STPCLK# active to DMI Message 0 t281 DMI Message to CPUSLP# active 60 t283 DMI Message to SUS_STAT# active 2 t284 SUS_STAT# active to PLTRST#, PCIRST# active (Desktop Only) 7 17 RTCCLK 1 8-17 2 10 RTCCLK 1 8-18 5 7 RTCCLK 1 8-18 1 2 RTCCLK 1 8-17 8-18 0 ms 4 8-18 0 ms 4 8-17 20 ns 23 8-18 8-28 RTCCLK 1 8-17 8-18 t285 t286 SUS_STAT# active to STP_PCI# active (Mobile Only) STP_PCI# active to PLTRST# and PCIRST# active 63 (Mobile Only) t287 t288 PLTRST#, PCIRST# active to SLP_S3# active SLP_S3# active to PWROK, VRMPWRGD inactive (Mobile Only) t289 SLP_S3# active to PWROK, VRMPWRGD inactive (Desktop Only) t290 PWROK, VRMPWRGD inactive to Vcc supplies inactive (nominal voltage -5%) (Mobile Only) t291 318 SLP_S3# active to SLP_S4# active 1 2 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Table 8-22. Power Management Timings (Sheet 3 of 3) Sym t294 Parameter Min PWROK, VRMPWRGD inactive to Vcc supplies inactive (nominal voltage -5%) Max Units Notes Fig ns 23 8-17 8-27 20 (Desktop Only) t295 SLP_S4# active to SLP_S5# active 1 2 RTCCLK 1, 5 8-17 8-18 t296 Wake Event to SLP_S5# inactive 1 10 RTCCLK 1 8-17 8-18 8 8-17 8-18 8-23 8-24 8-25 1 8-25 8 8-17 8-18 1 8-17 8-18 t297 SLP_S5# inactive to SLP_S4# inactive See Note Below t298 S4_STATE# inactive to SLP_S3# inactive t299 S4 Wake Event to SLP_S4# inactive (S4 Wake) t300 S3 Wake Event to SLP_S3# inactive (S3 Wake) 0 t301 S1 Wake Event to STPCLK# inactive 9 t302 SLP_M# inactive to SLP_S3# inactive ±10 ns t303 SLP_S4# inactive to SLP_M# inactive when Intel® AMT enabled ±10 ns 15 1 Note 16 RTCCLK See Note Below small as possible RTCCLK PCICLK 8-16 (Digital Office Only) t304 RSMRST# deassertion to LAN_RST# deassertion 0 ms 17 t305a LAN Power Rails active to LAN_RST# deassertion 1 ms 18 t305b LAN_RST# assertion to LAN power rails inactive 20 ns 25 t306 LANRST# assertion to PWROK assertion 0 ms t307 SLP_S3# active to Vcc supplies inactive (nominal voltage -5%) 5 us t308a RSMRST# deassertion to CLPWROK assertion 0 ms t308b Controller Link Power Rails active to CLPWROK assertion 1 ms t308c CLPWROK assertion to PWROK assertion 0 ms 24 8-17 8-18 Other Timings t310 THRMTRIP# active to SLP_S3#, SLP_S4#, SLP_S5# active 175 ns t311 RSMRST# rising edge transition from 20% to 80% 50 μs t312 RSMRST# falling edge transition t313 SLP_M# active to RSMRST# active Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 21 500 μs 8-18 319 Electrical Characteristics NOTES: 1. These transitions are clocked off the internal RTC. 1 RTC clock is approximately from 28.992 µs to 32.044 µs. 2. The ICH9 STPCLK# assertion will trigger the processor to send a stop grant acknowledge cycle. The timing for this cycle getting to the ICH9 is dependant on the processor and the memory controller. 3. These transitions are clocked off the 33 MHz PCICLK. 1 PCICLK is approximately 30 ns. 4. The ICH9 has no maximum timing requirement for this transition. It is up to the system designer to determine if the SLP_S3#, SLP_S4# and SLP_S5# signals are used to control the power planes. 5. If the transition to S5 is due to Power Button Override, SLP_S3#, SLP_S4# and SLP_S5# are asserted together similar to timing t287 (PCIRST# active to SLP_S3# active). 6. If there is no RTC battery in the system, so VccRTC and the VccSus supplies come up together, the delay from RTCRST# and RSMRST# inactive to SUSCLK toggling may be as much as 2.5 s. 7. This value is programmable in multiples of 1024 PCI CLKs. Maximum is 8192 PCI CLKs (245.6 µs). 8. The Min/Max times depend on the programming of the “SLP_S4# Minimum Assertion Width” and the “SLP_S4# Assertion Stretch Enable bits (D31:F0:A4h bits 5:3)”. 9. Note that this does not apply for synchronous SMIs. 10. This is a clock generator specification 11. If the (G)MCH does not have the CPUSLP# signal, then the minimum value can be 16 PCICLK. 12. This is non-zero to enforce the minimum assert time for DPRSLPVR. If the minimum assert time for DPRSLPVR has been met, then this is permitted to be 0. 13. This is non-zero to enforce the minimum assert time for STP_CPU#. If the minimum assert time for STP_CPU# has been met, then this is permitted to be 0. 14. This value should be at most a few clocks greater than the minimum. 15. When AMT enabled, S4_STATE# indicates if system is in S4 state or below. (Digital Office Only). 16. For t234 and t298, the SLP_M# stretching logic can push the Max value much larger than the Min (e.g., up to 3 seconds). With the installation of the Intel Manageability Engine firmware, the Max value of t234 and t298 is 99 ms. Without the installation of the firmware, the Max value is 4 RTC clocks. 17. RSMRST# must de-assert at or before LAN_RST# de-assertion. 18. Measured from VccLAN3_3 or VccLAN1_05 power within voltage spec (which ever is later in time) to LAN_RST# = (Vih+Vil)/2. It is acceptable to use an RC circuit sourced from VccLAN3_3 to create LAN_RST#. The rising edge of LAN_RST# needs to be a clean, monotonic edge for frequency content below 10 MHz. 19. If Integrated LAN is supported, LAN_RST# must be de-asserted at or before PWROK assertion. 20. If Integrated LAN is not supported, LANRST# should be tied to ground and must never deassert 21. RSMRST# falling edge must transition to 0.8 V or less before VccSus3_3 drops to 2.1 V 22. If bit 0 of Section 13.8.1.3 is set to a 1, SLP_S5# will not be de-asserted until a wake event is detected. If bit 0 is set to 0, SLP_S5# will de-assert within the specification listed in the table. 23. t290 and t294 are not applied to V5REF. V5REF timings are bonded by power sequencing. t290 and t294 apply during S0 to G3 transitions only. 24. t307 is applicable in S0 to Sx transitions. 25. A power rail is considered to be inactive when the rail is at its normal voltage minus 5% or less. 320 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics 8.5 Timing Diagrams Figure 8-1. Clock Timing Period High Time 2.0V 0.8V Low Time Fall Time Figure 8-2. Rise Time Valid Delay from Rising Clock Edge Clock 1.5V Valid Delay Output Figure 8-3. VT Setup and Hold Times Clock 1.5V Setup Time Input Intel® I/O Controller Hub 9 (ICH9) Family Datasheet VT Hold Time VT 321 Electrical Characteristics Figure 8-4. Float Delay Input VT Float Delay Output Figure 8-5. Pulse Width Pulse Width VT Figure 8-6. VT Output Enable Delay 1.5V Clock Output Enable Delay Output Figure 8-7. VT USB Rise and Fall Times Rise Time 90% CL Fall Time 90% Differential Data Lines 10% 10% CL tR tF Low-speed: 75 ns at CL = 50 pF, 300 ns at C L = 350 pF Full-speed: 4 to 20 ns at C L = 50 pF High-speed: 0.8 to 1.2 ns at C L = 10 pF 322 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Figure 8-8. USB Jitter T period Crossover Points Differential Data Lines Jitter Consecutive Transitions Paired Transitions Figure 8-9. USB EOP Width Tperiod Data Crossover Level Differential Data Lines EOP Width Figure 8-10. SMBus Transaction t19 t20 t21 SMBCLK t135 t131 t134 t133 t132 t18 SMBDATA t130 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 323 Electrical Characteristics Figure 8-11. SMBus Timeout Start Stop t137 CLKack CLKack t138 t138 SMBCLK SMBDATA Figure 8-12. SPI Timings t182 t182 SPI_CLK t183 SPI_MOSI t184 t185 SPI_MISO t186 t187 SPI_CS# 324 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Figure 8-13. Intel® High Definition Audio Input and Output Timings HDA_BIT_CLK HDA_SDOUT t143 t144 t143 t144 HDA_SDIN[3:0] t145 t146 Figure 8-14. Power Sequencing and Reset Signal Timings PWROK t214 V_CPU_IO t211 Vcc1_5_A, Vcc1_5_B Vcc1_05 and other power1 Vcc3_3 t209 t213 V5REF LAN_RST#, RSMRST# t204 t203 VccSus1_05 t202 VccSus3_3 t201 V5REF_Sus RTCRST# VccRTC t200 ICH7 P S D kt d NOTES: 1. Other power includes VccUSBPLL, VccDMIPLL, and VccSATAPLL. All of these power signals must independently meet the timings shown in the figure. There are no timing interdependencies between Vcc1_05 and these other power signals. There are also no timing interdependencies for these power signals, including Vcc1_05, to Vcc3_3 and Vcc1_5_A/Vcc1_5_B. 2. PWROK must not glitch, even if RSMRST# is low. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 325 Electrical Characteristics Figure 8-15. G3 (Mechanical Off) to S0 Timings System State G3 G3 S5 S4 S3 S0 S0 state DMI message STPCLK# Processor I/F signals Strap Values Normal Operation PLTRST# t218 SUS_STAT# T212 VRMPWRGD t217 PWROK t214 Vcc 1 SLP_S3# t230 t234 t233 SLP_S4# SLP_S5# t232 Running SUSCLK t231 RSMRST# LAN_RST# t204 VccSus1_05 t202 VccSus3_3 NOTE: 1. Vcc includes Vcc1_5_A, Vcc1_5_B, Vcc3_3, Vcc1_05, VccUSBPLL, VccDMIPLL, VccSATAPLL, V5REF and V_CPU_IO. 326 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Figure 8-16. S0 to S1 to S0 Timing S0 STATE S0 S1 S1 S1 S0 S0 t301 STPCLK# DMI Message t280 Wake Event Figure 8-17. S0 to S5 to S0 Timings (Desktop Only) S0 S0 S3 S3 S4 S5 S4 S3 S3/S4/S5 S0 S0 STPCLK# t280 DMI Message SUS_STAT# t283 PLTRST# SLP_M# t284 t218 t300 SLP_S3# t287 t299 SLP_S4# t234 t291 SLP_S5# t297 t295 t296 Wake Event t212 VRMPWRGD t289 PWROK t214 Vcc 1 t217 t307 NOTE: 1. Vcc includes Vcc1_5_A, Vcc1_5_B, Vcc3_3, Vcc1_05, VccUSBPLL, VccDMIPLL, and VccSATAPLL. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 327 Electrical Characteristics Figure 8-18. S0 to S5 to S0 Timings (Mobile Only) S0 S0 S3 S3 S4 S5 S3/S4/S5 S0 S0 STPCLK# DMI Message STP_CPU#, CPUSLP#, DPSLP#, DPRSTP# t280 DPRSLPVR SUS_STAT# t283 t217 STP_PCI# t285 t218 PLTRST# PCIRST# t286 SLP_M# t302 t300 SLP_S3# t287 t234 t299 SLP_S4# t291 t297 SLP_S5# t295 Wake Event t296 t307 PWROK t288 Vcc t214 RSMRST# t313 NOTE: Vcc includes Vcc1_5_A, Vcc1_5_B, Vcc3_3, Vcc1_05, VccUSBPLL, VccDMIPLL, and VccSATAPLL. Figure 8-19. C0 to C2 to C0 Timings (Mobile Only) CPU I/F Unlatched Signals Latched Unlatched STPCLK# Break Event 328 t250 t273 t274 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Figure 8-20. C0 to C3 to C0 Timings (Mobile Only) CPU I/F Signals Latched Unlatched Unlatched t274 STPCLK# t250 Bus Master Idle Active t270 t251 DPSLP# STP_CPU# t253 CPU Clocks t267 Running t269 Running Stopped t254 t268 Break Event Figure 8-21. C0 to C4 to C0 Timings (Mobile Only) CPU I/F Signals Latched Unlatched Unlatched t250 t274 STPCLK# Bus Master Active Idle t270 t251 DPSLP# t269 t253 STP_CPU# t268 t254 CPU Clocks Stopped Running Running t265 DPRSTP# DPRSLPVR t255 t266a CPU Vcc Break Event Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 329 Electrical Characteristics Figure 8-22. C0 to C5/C6 to C0 Timings (Mobile Only) CPU I/F Unlatched Signals Latched Unlatched t275 STPCLK# t274 t250 Bus Master Active DMI Message PMSYNC# t280 t252 t270 t269 DPSLP# t251 STP_CPU# CPU Clocks t253 t268 Running Stopped t254 Running t265 DPRSTP# t266b DPRSLPVR t255 CPU Vcc Break Event Figure 8-23. Sleep control signal relationship - Host boots and Management Engine off t234 SLP_S3# S4_STATE# t297 SLP_S4# SLP_S5# t302 SLP_M # NOTES: 1. t290 is also applicable when the system transitions from S0 to G3. 330 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Electrical Characteristics Figure 8-24. Sleep control signal relationship - Host and Management Engine boot after G3 t2 3 4 SLP_S3# t2 9 7 S4_STATE# SLP_S4# SLP_S5# SLP_M # NOTE: When both the host and Management Engine boot after G3, SLP_M# does not have any timing dependency on other sleep control signals. SLP_M# will be de-asserted some time between SLP_S5# de-assertion and SLP_S3# de-assertion. Figure 8-25. Sleep control signal relationship - Host stays in S5 and Management Engine boots after G3 t2 9 8 SLP_S3# t2 9 7 S4_STATE# SLP_S4# SLP_S5# W ake event t3 0 3 SLP_M # Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 331 Electrical Characteristics Figure 8-26. S4, S5/M1 to S0/M0 t2 9 8 SLP_S3# t2 9 7 S4_STATE# SLP_S4# SLP_S5# W ake event t3 0 3 SLP_M # NOTE: Vcc includes Vcc1_5_A, Vcc1_5_B, Vcc3_3, Vcc1_05, VccUSBPLL, VccDMIPLL, and VccSATAPLL. Figure 8-27. S0 to G3 Timings (Desktop Only) PW ROK V cc t294 Figure 8-28. S0 to G3 Timings (Mobile Only) PW ROK V cc t2 9 0 NOTE: Vcc includes Vcc1_5_A, Vcc1_5_B, Vcc3_3, Vcc1_05, VccUSBPLL, VccDMIPLL, and VccSATAPLL. §§ 332 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Register and Memory Mapping 9 Register and Memory Mapping The ICH9 contains registers that are located in the processor’s I/O space and memory space and sets of PCI configuration registers that are located in PCI configuration space. This chapter describes the ICH9 I/O and memory maps at the register-set level. Register access is also described. Register-level address maps and Individual register bit descriptions are provided in the following chapters. The following notations and definitions are used in the register/instruction description chapters. RO Read Only. In some cases, if a register is read only, writes to this register location have no effect. However, in other cases, two separate registers are located at the same location where a read accesses one of the registers and a write accesses the other register. See the I/O and memory map tables for details. WO Write Only. In some cases, if a register is write only, reads to this register location have no effect. However, in other cases, two separate registers are located at the same location where a read accesses one of the registers and a write accesses the other register. See the I/O and memory map tables for details. R/W Read/Write. A register with this attribute can be read and written. R/WC Read/Write Clear. A register bit with this attribute can be read and written. However, a write of 1 clears (sets to 0) the corresponding bit and a write of 0 has no effect. R/WO Read/Write-Once. A register bit with this attribute can be written only once after power up. After the first write, the bit becomes read only. R/WLO Read/Write, Lock-Once. A register bit with this attribute can be written to the non-locked value multiple times, but to the locked value only once. After the locked value has been written, the bit becomes read only. Reserved The value of reserved bits must never be changed. For details see Section 9.2. Default When ICH9 is reset, it sets its registers to predetermined default states. The default state represents the minimum functionality feature set required to successfully bring up the system. Hence, it does not represent the optimal system configuration. It is the responsibility of the system initialization software to determine configuration, operating parameters, and optional system features that are applicable, and to program the ICH9 registers accordingly. Bold Register bits that are highlighted in bold text indicate that the bit is implemented in the ICH9. Register bits that are not implemented or are hardwired will remain in plain text. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 333 Register and Memory Mapping 9.1 PCI Devices and Functions The Intel ICH9 incorporates a variety of PCI devices and functions, as shown in Table 9-1. They are divided into seven logical devices. The first is the DMI-To-PCI bridge (Device 30). The second device (Device 31) contains most of the standard PCI functions that always existed in the PCI-to-ISA bridges (South Bridges), such as the Intel PIIX4. The third and fourth (Device 29 and Device 26) are the USB and USB2 host controller devices. The fifth (Device 28) is PCI Express device. The sixth (Device 27) is HD Audio controller device, and the seventh (Device 25) is the Gigabit Ethernet controller device. If for some reason, the particular system platform does not want to support any one of the Device Functions, with the exception of D30:F0, they can individually be disabled. The integrated Gigabit Ethernet controller will be disabled if no Platform LAN Connect component is detected (See Chapter 5.3). When a function is disabled, it does not appear at all to the software. A disabled function will not respond to any register reads or writes, insuring that these devices appear hidden to software. b Table 9-1. PCI Devices and Functions Bus:Device:Function Function Description Bus 0:Device 30:Function 0 PCI-to-PCI Bridge Bus 0:Device 31:Function 0 LPC Controller1 Bus 0:Device 31:Function 2 SATA Controller #1 Bus 0:Device 31:Function 3 SMBus Controller Bus 0:Device 31:Function 5 SATA Controller #23 Bus 0:Device 31:Function 6 Thermal Subsystem Bus 0:Device 29:Function 0 USB UHCI Controller #1 Bus 0:Device 29:Function 1 USB UHCI Controller #2 Bus 0:Device 29:Function 2 USB UHCI Controller #3 Bus 0:Device 29:Function 3 USB UHCI Controller #62 Bus 0:Device 29:Function 7 USB EHCI Controller #1 Bus 0:Device 26:Function 0 USB UCHI Controller #4 Bus 0:Device 26:Function 1 USB UHCI Controller #5 Bus 0:Device 26:Function 2 USB UHCI Controller #62 Bus 0:Device 26:Fucntion 7 USB EHCI Controller #2 Bus 0:Device 28:Function 0 PCI Express* Port 1 Bus 0:Device 28:Function 1 PCI Express Port 2 Bus 0:Device 28:Function 2 PCI Express Port 3 Bus 0:Device 28:Function 3 PCI Express Port 4 Bus 0:Device 28:Function 4 PCI Express Port 5 Bus 0:Device 28:Function 5 PCI Express Port 6 Bus 0:Device 27:Function 0 Intel® High Definition Audio Controller Bus 0:Device 25:Function 0 Gigabit Ethernet Controller NOTES: 1. The PCI-to-LPC bridge contains registers that control LPC, Power Management, System Management, GPIO, Processor Interface, RTC, Interrupts, Timers, and DMA. 334 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Register and Memory Mapping 2. 3. 9.2 The ICH9 can optionally configure the USB ports from a 6-6 configuration into a 8-4 configuration, with 8 ports on D29:F7 EHCI and 4 ports on D26:F7 EHCI. In the 8-4 configuration UHCI #6 will be mapped to D29:F3. In the 6-6 configuration UHCI #6 will be mapped to D26:F2. SATA controller 2 (D31:F5) is only visible in ICH9 desktop components and when D31:F2 CC.SCC=01h. PCI Configuration Map Each PCI function on the ICH9 has a set of PCI configuration registers. The register address map tables for these register sets are included at the beginning of the chapter for the particular function. Configuration Space registers are accessed through configuration cycles on the PCI bus by the Host bridge using configuration mechanism #1 detailed in the PCI Local Bus Specification, Revision 2.3. Some of the PCI registers contain reserved bits. Software must deal correctly with fields that are reserved. On reads, software must use appropriate masks to extract the defined bits and not rely on reserved bits being any particular value. On writes, software must ensure that the values of reserved bit positions are preserved. That is, the values of reserved bit positions must first be read, merged with the new values for other bit positions and then written back. Note the software does not need to perform read, merge, write operation for the configuration address register. In addition to reserved bits within a register, the configuration space contains reserved locations. Software should not write to reserved PCI configuration locations in the device-specific region (above address offset 3Fh). 9.3 I/O Map The I/O map is divided into Fixed and Variable address ranges. Fixed ranges cannot be moved, but in some cases can be disabled. Variable ranges can be moved and can also be disabled. 9.3.1 Fixed I/O Address Ranges Table 9-2 shows the Fixed I/O decode ranges from the processor perspective. Note that for each I/O range, there may be separate behavior for reads and writes. DMI (Direct Media Interface) cycles that go to target ranges that are marked as “Reserved” will not be decoded by the ICH9, and will be passed to PCI unless the Subtractive Decode Policy bit is set (D31:F0:Offset 42h, bit 0). If a PCI master targets one of the fixed I/O target ranges, it will be positively decoded by the ICH9 in medium speed. Address ranges that are not listed or marked “Reserved” are not decoded by the ICH9 (unless assigned to one of the variable ranges). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 335 Register and Memory Mapping Table 9-2. 336 Fixed I/O Ranges Decoded by Intel® ICH9 (Sheet 1 of 2) I/O Address Read Target Write Target Internal Unit 00h–08h DMA Controller DMA Controller DMA 09h–0Eh RESERVED DMA Controller DMA 0Fh DMA Controller DMA Controller DMA 10h–18h DMA Controller DMA Controller DMA 19h–1Eh RESERVED DMA Controller DMA 1Fh DMA Controller DMA Controller DMA 20h–21h Interrupt Controller Interrupt Controller Interrupt 24h–25h Interrupt Controller Interrupt Controller Interrupt 28h–29h Interrupt Controller Interrupt Controller Interrupt 2Ch–2Dh Interrupt Controller Interrupt Controller Interrupt 2E–2F LPC SIO LPC SIO Forwarded to LPC 30h–31h Interrupt Controller Interrupt Controller Interrupt 34h–35h Interrupt Controller Interrupt Controller Interrupt 38h–39h Interrupt Controller Interrupt Controller Interrupt 3Ch–3Dh Interrupt Controller Interrupt Controller Interrupt 40h–42h Timer/Counter Timer/Counter PIT (8254) 43h RESERVED Timer/Counter PIT 4E–4F LPC SIO LPC SIO Forwarded to LPC 50h–52h Timer/Counter Timer/Counter PIT 53h RESERVED Timer/Counter PIT 60h Microcontroller Microcontroller Forwarded to LPC 61h NMI Controller NMI Controller Processor I/F 62h Microcontroller Microcontroller Forwarded to LPC 64h Microcontroller Microcontroller Forwarded to LPC 66h Microcontroller Microcontroller Forwarded to LPC 70h RESERVED NMI and RTC Controller RTC 71h RTC Controller RTC Controller RTC 72h RTC Controller NMI and RTC Controller RTC 73h RTC Controller RTC Controller RTC 74h RTC Controller NMI and RTC Controller RTC 75h RTC Controller RTC Controller RTC 76h RTC Controller NMI and RTC Controller RTC 77h RTC Controller RTC Controller RTC 80h DMA Controller, or LPC, or PCI DMA Controller and LPC or PCI DMA 81h–83h DMA Controller DMA Controller DMA Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Register and Memory Mapping Table 9-2. Fixed I/O Ranges Decoded by Intel® ICH9 (Sheet 2 of 2) I/O Address Read Target Write Target Internal Unit 84h–86h DMA Controller DMA Controller and LPC or PCI DMA 87h DMA Controller DMA Controller DMA 88h DMA Controller DMA Controller and LPC or PCI DMA 89h–8Bh DMA Controller DMA Controller DMA 8Ch–8Eh DMA Controller DMA Controller and LPC or PCI DMA 08Fh DMA Controller DMA Controller DMA 90h–91h DMA Controller DMA Controller DMA 92h Reset Generator Reset Generator Processor I/F 93h–9Fh DMA Controller DMA Controller DMA A0h–A1h Interrupt Controller Interrupt Controller Interrupt A4h–A5h Interrupt Controller Interrupt Controller Interrupt A8h–A9h Interrupt Controller Interrupt Controller Interrupt ACh–ADh Interrupt Controller Interrupt Controller Interrupt B0h–B1h Interrupt Controller Interrupt Controller Interrupt B2h–B3h Power Management Power Management Power Management B4h–B5h Interrupt Controller Interrupt Controller Interrupt B8h–B9h Interrupt Controller Interrupt Controller Interrupt BCh–BDh Interrupt Controller Interrupt Controller Interrupt C0h–D1h DMA Controller DMA Controller DMA D2h–DDh RESERVED DMA Controller DMA DEh–DFh DMA Controller DMA Controller DMA F0h PCI and Master Abort1 FERR#/IGNNE# / Interrupt Controller Processor I/F 170h–177h SATA Controller or PCI SATA Controller or PCI Forwarded to SATA 1F0h–1F7h SATA Controller or PCI SATA Controller or PCI Forwarded to SATA 376h SATA Controller or PCI SATA Controller or PCI Forwarded to SATA 3F6h SATA Controller or PCI SATA Controller or PCI Forwarded to SATA 4D0h–4D1h Interrupt Controller Interrupt Controller Interrupt CF9h Reset Generator Reset Generator Processor I/F NOTE: 1. A read to this address will subtractively go to PCI, where it will master abort. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 337 Register and Memory Mapping 9.3.2 Variable I/O Decode Ranges Table 9-3 shows the Variable I/O Decode Ranges. They are set using Base Address Registers (BARs) or other configuration bits in the various PCI configuration spaces. The PNP software (PCI or ACPI) can use their configuration mechanisms to set and adjust these values. Warning: The Variable I/O Ranges should not be set to conflict with the Fixed I/O Ranges. Unpredictable results if the configuration software allows conflicts to occur. The ICH9 does not perform any checks for conflicts. Table 9-3. Variable I/O Decode Ranges Mappable Size (Bytes) Target ACPI Anywhere in 64 KB I/O Space 64 Power Management IDE Bus Master Anywhere in 64 KB I/O Space 16 IDE Unit Native IDE Command Anywhere in 64 KB I/O Space 8 IDE Unit Native IDE Control Anywhere in 64 KB I/O Space 4 IDE Unit USB UHCI Controller #1 Anywhere in 64 KB I/O Space 32 USB Unit 1 USB UHCI Controller #2 Anywhere in 64 KB I/O Space 32 USB Unit 2 USB UHCI Controller #3 Anywhere in 64 KB I/O Space 32 USB Unit 3 USB UHCI Controller #4 Anywhere in 64 KB I/O Space 32 USB Unit 4 USB UHCI Controller #5 Anywhere in 64 KB I/O Space 32 USB Unit 5 USB UHCI Controller #6 Anywhere in 64 KB I/O Space 32 USB Unit 6 SMBus Anywhere in 64 KB I/O Space 32 SMB Unit TCO 96 Bytes above ACPI Base 32 TCO Unit GPIO Anywhere in 64 KB I/O Space 64 GPIO Unit Parallel Port 3 Ranges in 64 KB I/O Space 8 LPC Peripheral Serial Port 1 8 Ranges in 64 KB I/O Space 8 LPC Peripheral Serial Port 2 8 Ranges in 64 KB I/O Space 8 LPC Peripheral Range Name Floppy Disk Controller 2 Ranges in 64 KB I/O Space 8 LPC Peripheral LAN Anywhere in 64 KB I/O Space 32 LAN Unit LPC Generic 1 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral LPC Generic 2 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral LPC Generic 3 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral LPC Generic 4 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral I/O Trapping Ranges Anywhere in 64 KB I/O Space 1 to 256 Trap on Backbone NOTE: 1. Decode range size determined by D31:F0:ADh:bits 5:4 338 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Register and Memory Mapping 9.4 Memory Map Table 9-4 shows (from the processor perspective) the memory ranges that the ICH9 decodes. Cycles that arrive from DMI that are not directed to any of the internal memory targets that decode directly from DMI will be driven out on PCI unless the Subtractive Decode Policy bit is set (D31:F0:Offset 42h, bit 0). PCI cycles generated by external PCI masters will be positively decoded unless they fall in the PCI-to-PCI bridge memory forwarding ranges (those addresses are reserved for PCI peer-to-peer traffic). If the cycle is not in the internal LAN controller’s range, it will be forwarded up to DMI. Software must not attempt locks to the ICH9’s memorymapped I/O ranges for EHCI and HPET. If attempted, the lock is not honored which means potential deadlock conditions may occur. Table 9-4. Memory Decode Ranges from Processor Perspective (Sheet 1 of 2) Memory Range Target Dependency/Comments 0000 0000h–000D FFFFh 0010 0000h–TOM (Top of Memory) Main Memory TOM registers in Host controller 000E 0000h–000E FFFFh Firmware Hub Bit 6 in Firmware Hub Decode Enable register is set 000F 0000h–000F FFFFh Firmware Hub Bit 7 in Firmware Hub Decode Enable register is set FEC0 x000h–FEC0 x040h IO(x) APIC inside ICH9 X is controlled via APIC Range Select (ASEL) field and APIC Enable (AEN) bit FEC1 0000h–FEC1 7FFF PCI Express* Port 1 PCI Express* Root Port 1 I/OxAPIC Enable (PAE) set FEC1 8000h–FEC1 8FFFh PCI Express* Port 2 PCI Express* Root Port 2 I/OxAPIC Enable (PAE) set FEC2 0000h–FEC2 7FFFh PCI Express* Port 3 PCI Express* Root Port 3 I/OxAPIC Enable (PAE) set FEC2 8000h–FEC2 8FFFh PCI Express* Port 4 PCI Express* Root Port 4 I/OxAPIC Enable (PAE) set FEC3 0000h–FEC3 7FFFh PCI Express* Port 5 PCI Express* Root Port 5 I/OxAPIC Enable (PAE) set FEC3 8000h–FEC3 8FFFh PCI Express* Port 6 PCI Express* Root Port 6 I/OxAPIC Enable (PAE) set FED4 0000h–FED4 BFFFh TPM on LPC FFC0 0000h–FFC7 FFFFh Firmware Hub (or PCI)2 Bit 8 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 9 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 10 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 11 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 12 in Firmware Hub Decode Enable register is set FF80 0000h–FF87 FFFFh FFC8 0000h–FFCF FFFFh FF88 0000h–FF8F FFFFh FFD0 0000h–FFD7 FFFFh FF90 0000h–FF97 FFFFh FFD8 0000h–FFDF FFFFh FF98 0000h–FF9F FFFFh FFE0 000h–FFE7 FFFFh FFA0 0000h–FFA7 FFFFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 339 Register and Memory Mapping Table 9-4. Memory Decode Ranges from Processor Perspective (Sheet 2 of 2) Memory Range Target Dependency/Comments FFE8 0000h–FFEF FFFFh Firmware Hub (or PCI)3 Bit 13 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 14 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Always enabled. The top two, 64 KB blocks of this range can be swapped, as described in Section 7.4.1. Firmware Hub (or PCI)2 Bit 3 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 2 in Firmware Hub Decode Enable register is set Firmware Hub (or PCI)2 Bit 1 in Firmware Hub Decode Enable register is set FF00 0000h–FF0F FFFFh Firmware Hub (or PCI)2 Bit 0 in Firmware Hub Decode Enable register is set 128 KB anywhere in 4-GB range Integrated LAN Controller Enable via BAR in Device 25:Function 0 (Integrated LAN Controller) 1 KB anywhere in 4-GB range USB EHCI Controller #11 Enable via standard PCI mechanism (Device 29, Function 7) 1 KB anywhere in 4-GB range USB EHCI Controller #21 Enable via standard PCI mechanism (Device 26, Function 7) 512 B anywhere in 64-bit addressing space Intel® High Definition Audio Host Controller Enable via standard PCI mechanism (Device 27, Function 0) FED0 X000h–FED0 X3FFh High Precision Event Timers 1 BIOS determines the “fixed” location which is one of four, 1-KB ranges where X (in the first column) is 0h, 1h, 2h, or 3h. All other PCI FFA8 0000h–FFAF FFFFh FFF0 0000h–FFF7 FFFFh FFB0 0000h–FFB7 FFFFh FFF8 0000h–FFFF FFFFh FFB8 0000h–FFBF FFFFh FF70 0000h–FF7F FFFFh FF30 0000h–FF3F FFFFh FF60 0000h–FF6F FFFFh FF20 0000h–FF2F FFFFh FF50 0000h–FF5F FFFFh FF10 0000h–FF1F FFFFh FF40 0000h–FF4F FFFFh None NOTES: 1. Software must not attempt locks to memory mapped I/O ranges for USB EHCI or High Precision Event Timers. If attempted, the lock is not honored, which means potential deadlock conditions may occur. 2. PCI is the target when the Boot BIOS Destination selection bits are set to 10b (Chipset Config Registers:Offset 3401 bits 11:10). When PCI selected, the Firmware Hub Decode Enable bits have no effect. 9.4.1 Boot-Block Update Scheme The ICH9 supports a “top-block swap” mode that has the ICH9 swap the top block in the Firmware Hub (the boot block) with another location. This allows for safe update of the Boot Block (even if a power failure occurs). When the “TOP_SWAP” Enable bit is set, the ICH9 will invert A16 for cycles targeting Firmware Hub space. When this bit is 0, the ICH9 will not invert A16. This bit is automatically set to 0 by RTCRST#, but not by PLTRST#. The scheme is based on the concept that the top block is reserved as the “boot” block, and the block immediately below the top block is reserved for doing boot-block updates. 340 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Register and Memory Mapping The algorithm is: 1. Software copies the top block to the block immediately below the top 2. Software checks that the copied block is correct. This could be done by performing a checksum calculation. 3. Software sets the TOP_SWAP bit. This will invert A16 for cycles going to the Firmware Hub. processor access to FFFF_0000h through FFFF_FFFFh will be directed to FFFE_0000h through FFFE_FFFFh in the Firmware Hub, and processor accesses to FFFE_0000h through FFFE_FFFF will be directed to FFFF_0000h through FFFF_FFFFh. 4. Software erases the top block 5. Software writes the new top block 6. Software checks the new top block 7. Software clears the TOP_SWAP bit 8. Software sets the Top_Swap Lock-Down bit If a power failure occurs at any point after step 3, the system will be able to boot from the copy of the boot block that is stored in the block below the top. This is because the TOP_SWAP bit is backed in the RTC well. Note: The top-block swap mode may be forced by an external strapping option (See Section 2.24.1). When top-block swap mode is forced in this manner, the TOP_SWAP bit cannot be cleared by software. A re-boot with the strap removed will be required to exit a forced top-block swap mode. Note: Top-block swap mode only affects accesses to the Firmware Hub space, not feature space. Note: The top-block swap mode has no effect on accesses below FFFE_0000h. §§ Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 341 Register and Memory Mapping 342 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10 Chipset Configuration Registers This section describes all registers and base functionality that is related to chipset configuration and not a specific interface (such as LPC, PCI, or PCI Express*). It contains the root complex register block, which describes the behavior of the upstream internal link. This block is mapped into memory space, using the Root Complex Base Address (RCBA) register of the PCI-to-LPC bridge. Accesses in this space must be limited to 32-(DW) bit quantities. Burst accesses are not allowed. All Chipset Configuration Registers are located in the core well unless otherwise indicated. 10.1 Chipset Configuration Registers (Memory Space) Note: Address locations that are not shown should be treated as Reserved (see Section 9.2 for details). . Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 1 of 4) Offset Mnemonic 0000–0003h VCH Register Name Virtual Channel Capability Header Default Type 10010002h R/WO 0004–0007h VCAP1 Virtual Channel Capability #1 00000801h RO, R/WO 0008–000Bh VCAP2 Virtual Channel Capability #2 00000001h RO 000C–000Dh PVC Port VC Control 0000h RO, R/W 000E–000Fh PVS Port VC Status 0000h RO 0010–0013h V0CAP VC 0 Resource Capability 00000001h RO 0014–0017h V0CTL VC 0 Resource Control 800000FFh R/W, RO 001A–001Bh V0STS VC 0 Resource Status 0000h RO 001C–001Fh V1CAP VC 1 Resource Capability 03008011h R/WO, RO 0020–0023h V1CTL VC 1 Resource Control 00000000h R/W 0026–0027h V1STS VC 1 Resource Status 0000h RO 0030-006Fh PAT Port Arbitration Table 0088-008Bh CIR1 00000000h R/WO 00AC-00AFh REC 0000h R/W 1A010005h RO Chipset Initialization Register 1 Root Error Command Root Complex Topology Capability List 0100–0103h RCTCL 0104–0107h ESD Element Self Description 00000802h R/WO, RO 0110–0113h ULD Upstream Link Descriptor 00000001h R/WO, RO 0118–011Fh ULBA Upstream Link Base Address 0000000000000000h R/WO 0120–0123h RP1D Root Port 1 Descriptor 01xx0002h R/WO, RO 0128–012Fh RP1BA 0130–0133h RP2D Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Root Port 1 Base Address Root Port 2 Descriptor 00000000000E0000h RO 02xx0002h R/WO, RO 343 Chipset Configuration Registers Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 2 of 4) 344 Offset Mnemonic 0138–013Fh RP2BA 0140–0143h RP3D 0148–014Fh RP3BA 0150–0153h RP4D 0158–015Fh RP4BA Register Name Root Port 2 Base Address Root Port 3 Descriptor Root Port 3 Base Address Root Port 4 Descriptor Root Port 4 Base Address Intel® High Definition Audio Descriptor 0160–0163h HDD 0168–016Fh HDBA 0170–0173h RP5D Root Port 5 Descriptor 0178–017Fh RP5A Root Port 5 Base Address 0180–0183h RP6D Root Port 6 Descriptor 0188–018Fh RP6BA Intel High Definition Audio Base Address Root Port 6 Base Address Default Type 00000000000E1000h RO 03xx0002h R/WO, RO 00000000000E2000h RO 04xx0002h R/WO, RO 00000000000E3000h RO 15xx0002h R/WO, RO 00000000000D8000h RO 05xx0002h R/WO, RO 00000000000E4000h RO 06xx0002h R/WO, RO 00000000000E5000h RO 01A0–01A3h ILCL Internal Link Capability List 00010006h RO 01A4–01A7h LCAP Link Capabilities 00012841h RO, R/WO 01A8–01A9h LCTL Link Control 0000h R/W 01AA–01ABh LSTS Link Status 0041h RO 01F4-01F7h CIR2 Chipset Initialization Register 2 00000000h R/W 01FC-01FDh CIR3 Chipset Initialization Register 3 0000h R/W 0220-0223h BCR Backbone Configuration 00000000h R/W 0224–0227h RPC Root Port Configuration 0000000yh R/W, RO 0234-0327h DMIC DMI Control 00000000h R/W, RO 0238–023Bh RPFN Root Port Function Number for PCI Express Root Ports 00543210h R/WO, RO 0290-0293h FPSS Function Level Reset Pending Status Summary 00000000h RO 0F20-0F23h CIR13 Chipset Initialization Register 13 B2B477CCh R/W 1D40-1D47h CIR5 Chipset Initialization Register 5 0000000000000000h R/W 1E00–1E03h TRSR Trap Status Register 00000000h R/WC, RO 1E10–1E17h TRCR Trapped Cycle Register 0000000000000000h RO 1E18-1E1Fh TWDR Trapped Write Data Register 0000000000000000h RO 1E80-1E87h IOTR0 I/O Trap Register 0 0000000000000000h R/W 1E88-1E8Fh IOTR1 I/O Trap Register 1 0000000000000000h R/W 1E90-1E97h IOTR2 I/O Trap Register 2 0000000000000000h R/W 1E98-1E9Fh IOTR3 I/O Trap Register 3 0000000000000000h R/W 2010-2013h DMC DMI Miscellaneous Control register 00000002h R/W 2024-2027h CIR6 Chipset Initialization Register 6 (Mobile Only) 0B4030C0h R/W Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 3 of 4) Offset Mnemonic Register Name Default Type 2034-2037h CIR7 Chipset Initialization Register 7 B2B477CCh R/W 20C4-20C5h CIR11 Chipset Initialization Register 11 (Mobile Only) 0000h R/W 20E4-20E5h CIR12 Chipset Initialization Register 12 (Mobile Only) 0000h R/W 3000–3000h TCTL 00h R/W 3100–3103h D31IP Device 31 Interrupt Pin TCO Control 03243200h R/W, RO 3104–3107h D30IP Device 30 Interrupt Pin 00000000h RO 3108–310Bh D29IP Device 29 Interrupt Pin 10004321h R/W 310C–310Fh D28IP Device 28 Interrupt Pin 00214321h R/W 3110–3113h D27IP Device 27 Interrupt Pin 00000001h R/W 3114–3117h D26IP Device 26 Interrupt Pin 30000321h R/W 3118–311Bh D25IP Device 25 Interrupt Pin 00000001h R/W 3140–3141h D31IR Device 31 Interrupt Route 3210h R/W 3142–3143h D30IR Device 30 Interrupt Route 0000h RO 3144–3145h D29IR Device 29 Interrupt Route 3210h R/W 3146–3147h D28IR Device 28 Interrupt Route 3210h R/W 3148–3149h D27IR Device 27 Interrupt Route 3210h R/W 314C–314Dh D26IR Device 26 Interrupt Route 3210h R/W 3150–3151h D25IR Device 25 Interrupt Route 3210h R/W 31FF–31FFh OIC 00h R/W 3300-3303h SBEMC3 Scheduled Break Event C3 (Mobile Only) 00000000h R/W 3304-3307h SBEMC4 Schedule Break Event C4 (Mobile Only) 00000000h R/W 3400–3403h RC RTC Configuration 00000000h R/W, R/WLO 3404–3407h HPTC High Precision Timer Configuration 00000000h R/W 3410–3413h GCS General Control and Status 000000yy0h R/W, R/WLO 3414–3414h BUC Backed Up Control 00h R/W Other Interrupt Control 3418–341Bh FD Function Disable 00000000h R/W 341C–341Fh CG Clock Gating 00000000h R/W 3420–3420h PDSW 00h R/W 3430-3433h CIR8 Chipset Initialization Register 8 00000000h R/W 350C-350Fh CIR9 Chipset Initialization Register 9 00000000h R/W Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Function Disable SUS Well 345 Chipset Configuration Registers Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 4 of 4) 10.1.1 Offset Mnemonic 3524–3525h PPO 352C-352Fh CIR10 35F0-35F3h MAP Register Name USB Port Power Off Chipset Initialization Register 10 USB Remap Control Bit 0000h R/W 0008C008hh R/W 00000000h R/WO Attribute: Size: R/WO 32-bit Description 31:20 Next Capability Offset (NCO) — R/WO. Indicates the next item in the list. 19:16 Capability Version (CV) — R/WO. Indicates support as a version 1 capability structure. 15:0 Capability ID (CID) — R/WO. Indicates this is the Virtual Channel capability item. VCAP1—Virtual Channel Capability #1 Register Offset Address: 0004–0007h Default Value: 00000801h Bit Attribute: Size: RO, R/WO 32-bit Description 31:12 Reserved 11:10 Port Arbitration Table Entry Size (PATS) — RO. Indicates the size of the port arbitration table is 4 bits (to allow up to 8 ports). 9:8 7 6:4 3 2:0 346 Type VCH—Virtual Channel Capability Header Register Offset Address: 0000–0003h Default Value: 10010002h 10.1.2 Default Reference Clock (RC) — RO. Fixed at 100 ns. Reserved Low Priority Extended VC Count (LPEVC) — RO. Indicates that there are no additional VCs of low priority with extended capabilities. Reserved Extended VC Count (EVC) — R/WO. Indicates that there is one additional VC (VC1) that exists with extended capabilities. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.3 VCAP2—Virtual Channel Capability #2 Register Offset Address: 0008–000Bh Default Value: 00000001h Description 31:24 VC Arbitration Table Offset (ATO) — RO. Indicates that no table is present for VC arbitration since it is fixed. 7:0 Reserved VC Arbitration Capability (AC) — RO. Indicates that the VC arbitration is fixed in the root complex. PVC—Port Virtual Channel Control Register Offset Address: 000C–000Dh Default Value: 0000h Bit 15:04 10.1.5 RO 32-bit Bit 23:8 10.1.4 Attribute: Size: Attribute: Size: RO, R/W 16-bit Description Reserved 3:1 VC Arbitration Select (AS) — R/W. Indicates which VC should be programmed in the VC arbitration table. The root complex takes no action on the setting of this field since there is no arbitration table. 0 Load VC Arbitration Table (LAT) — RO. Indicates that the table programmed should be loaded into the VC arbitration table. This bit is defined as read/write with always returning 0 on reads. PVS—Port Virtual Channel Status Register Offset Address: 000E–000Fh Default Value: 0000h Bit 15:1 0 Attribute: Size: RO 16-bit Description Reserved VC Arbitration Table Status (VAS) — RO. Indicates the coherency status of the VC Arbitration table when it is being updated. This field is always 0 in the root complex since there is no VC arbitration table. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 347 Chipset Configuration Registers 10.1.6 V0CAP—Virtual Channel 0 Resource Capability Register Offset Address: 0010–0013h Default Value: 00000001h RO 32-bit Bit Description 31:24 Port Arbitration Table Offset (AT) — RO. This VC implements no port arbitration table since the arbitration is fixed. 23 22:16 Reserved Maximum Time Slots (MTS) — RO. This VC implements fixed arbitration, and therefore this field is not used. 15 Reject Snoop Transactions (RTS) — RO. This VC must be able to take snoopable transactions. 14 Advanced Packet Switching (APS) — RO. This VC is capable of all transactions, not just advanced packet switching transactions. 13:8 7:0 348 Attribute: Size: Reserved Port Arbitration Capability (PAC) — RO. Indicates that this VC uses fixed port arbitration. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.7 V0CTL—Virtual Channel 0 Resource Control Register Offset Address: 0014–0017h Default Value: 800000FFh Bit 31 R/W, RO 32-bit Description Virtual Channel Enable (EN) — RO. Always set to 1. VC0 is always enabled and cannot be disabled. 30:27 Reserved 26:24 Virtual Channel Identifier (ID) — RO. Indicates the ID to use for this virtual channel. 23:20 Reserved 19:17 Port Arbitration Select (PAS) — R/W. Indicates which port table is being programmed. The root complex takes no action on this setting since the arbitration is fixed and there is no arbitration table. 16 15:8 7:1 0 10.1.8 Attribute: Size: Load Port Arbitration Table (LAT) — RO. The root complex does not implement an arbitration table for this virtual channel. Reserved Transaction Class / Virtual Channel Map (TVM) — R/W. Indicates which transaction classes are mapped to this virtual channel. When a bit is set, this transaction class is mapped to the virtual channel. Reserved V0STS—Virtual Channel 0 Resource Status Register Offset Address: 001A–001Bh Default Value: 0000h Bit 15:2 Attribute: Size: RO 16-bit Description Reserved 1 VC Negotiation Pending (NP) — RO. When set, indicates the virtual channel is still being negotiated with ingress ports. 0 Port Arbitration Tables Status (ATS) — RO. There is no port arbitration table for this VC, so this bit is reserved at 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 349 Chipset Configuration Registers 10.1.9 V1CAP—Virtual Channel 1 Resource Capability Register Offset Address: 001C–001Fh Default Value: 03008011h Bit 31:24 23 22:16 Description Port Arbitration Table Offset (AT) — RO. Indicates the location of the port arbitration table in the root complex. A value of 3h indicates the table is at offset 30h. Reserved Maximum Time Slots (MTS) — R/WO. This value is updated by platform BIOS based upon the determination of the number of time slots available in the platform. Reject Snoop Transactions (RTS) — RO. All snoopable transactions on VC1 are rejected. This VC is for isochronous transfers only. 14 Advanced Packet Switching (APS) — RO. This VC is capable of all transactions, not just advanced packet switching transactions. 7:0 Reserved Port Arbitration Capability (PAC) — RO. Indicates the port arbitration capability is time-based WRR of 128 phases. V1CTL—Virtual Channel 1 Resource Control Register Offset Address: 0020–0023h Default Value: 00000000h Bit 31 Attribute: Size: R/W 32-bit Description Virtual Channel Enable (EN) — R/W. Enables the VC when set. Disables the VC when cleared. 30:27 Reserved 26:24 Virtual Channel Identifier (ID) — R/W. Indicates the ID to use for this virtual channel. 23:20 Reserved 19:17 Port Arbitration Select (PAS) — R/W. Indicates which port table is being programmed. The only permissible value of this field is 4h for the time-based WRR entries. 16 15:8 7:1 0 350 R/WO, RO 32-bit 15 13:8 10.1.10 Attribute: Size: Load Port Arbitration Table (LAT) — R/W. When set, the port arbitration table loaded based upon the PAS field in this register. This bit always returns 0 when read. Reserved Transaction Class / Virtual Channel Map (TVM) — R/W. Indicates which transaction classes are mapped to this virtual channel. When a bit is set, this transaction class is mapped to the virtual channel. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.11 V1STS—Virtual Channel 1 Resource Status Register Offset Address: 0026–0027h Default Value: 0000h Bit 15:2 10.1.12 Attribute: Size: RO 16-bit Description Reserved 1 VC Negotiation Pending (NP) — RO. When set, indicates the virtual channel is still being negotiated with ingress ports. 0 Port Arbitration Tables Status (ATS) — RO. Indicates the coherency status of the port arbitration table. This bit is set when LAT (offset 000Ch:bit 0) is written with value 1 and PAS (offset 0014h:bits19:17) has value of 4h. This bit is cleared after the table has been updated. PAT—Port Arbitration Table Offset Address: 0030-006Fh Default Value: Attribute: Size: 64-Byte This a 64-byte register that contains the arbitration table to be loaded into the port arbitration table. Every 4-bits contains an entry for one of the downstream PCI Express* ports or a 0h to indicate idol. The ports are mapped as follows: • Port 1: Value used is 1h. • Port 2: Value used is 2h. • Port 3: Value used is 3h. • Port 4: Value used is 4h. • Port 5: Value used is 5h. • Port 6: Value used is 6h. • Intel® High Definition Audio: Value used is Fh. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 351 Chipset Configuration Registers 10.1.13 CIR1—Chipset Initialization Register 1 Offset Address: 0088–008Bh Default Value: 00000000h Bit 31:21 20 19:16 15 14:13 12 11:0 10.1.14 Attribute: Size: R/WO 32-bit Description Reserved CIR1 Field 3 — R/WO. BIOS must set this bit. Reserved CIR1 Field 2 — R/WO. BIOS must set this bit. Reserved CIR1 Field 1— R/WO. BIOS must set this bit. Reserved REC—Root Error Command Register Offset Address: 00AC–00AFh Default Value: 0000h Bit Attribute: Size: R/W 32-bit Description Drop Poisoned Downstream Packets (DPDP) — R/W. Determines how downstream packets on DMI are handled that are received with the EP field set, indicating poisoned data: 31 1: This packet and all subsequent packets with data received on DMI for any VC will have their Unsupported Transaction (UT) field set causing them to master Abort downstream. Packets without data such as memory, IO and config read requests are allowed to proceed. 0: Packets are forwarded downstream without forcing the UT field set. 30:0 10.1.15 Reserved RCTCL—Root Complex Topology Capabilities List Register Offset Address: 0100–0103h Default Value: 1A010005h Bit RO 32-bit Description 31:20 Next Capability (NEXT) — RO. Indicates the next item in the list. 19:16 Capability Version (CV) — RO. Indicates the version of the capability structure. 15:0 352 Attribute: Size: Capability ID (CID) — RO. Indicates this is a PCI Express* link capability section of an RCRB. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.16 ESD—Element Self Description Register Offset Address: 0104–0107h Default Value: 00000802h Bit Description Port Number (PN) — RO. A value of 0 to indicate the egress port for the Intel® ICH9. 23:16 Component ID (CID) — R/WO. Indicates the component ID assigned to this element by software. This is written once by platform BIOS and is locked until a platform reset. Number of Link Entries (NLE) — RO. Indicates that one link entry (corresponding to DMI), 6 root port entries (for the downstream ports), and the Intel® High Definition Audio device are described by this RCRB. 7:4 Reserved 3:0 Element Type (ET) — RO. Indicates that the element type is a root complex internal link. ULD—Upstream Link Descriptor Register Offset Address: 0110–0113h Default Value: 00000001h Attribute: Size: R/WO, RO 32-bit Bit Description 31:24 Target Port Number (PN) — R/WO. This field is programmed by platform BIOS to match the port number of the (G)MCH RCRB that is attached to this RCRB. 23:16 Target Component ID (TCID) — R/WO. This field is programmed by platform BIOS to match the component ID of the (G)MCH RCRB that is attached to this RCRB. 15:2 10.1.18 R/WO, RO 32-bit 31:24 15:8 10.1.17 Attribute: Size: Reserved 1 Link Type (LT) — RO. Indicates that the link points to the (G)MCH RCRB. 0 Link Valid (LV) — RO. Indicates that the link entry is valid. ULBA—Upstream Link Base Address Register Offset Address: 0118–011Fh Default Value: 0000000000000000h Attribute: Size: R/WO 64-bit Bit Description 63:32 Base Address Upper (BAU) — R/WO. This field is programmed by platform BIOS to match the upper 32-bits of base address of the (G)MCH RCRB that is attached to this RCRB. 31:0 Base Address Lower (BAL) — R/WO. This field is programmed by platform BIOS to match the lower 32-bits of base address of the (G)MCH RCRB that is attached to this RCRB. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 353 Chipset Configuration Registers 10.1.19 RP1D—Root Port 1 Descriptor Register Offset Address: 0120–0123h Default Value: 01xx0002h Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 1h (root port #1). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When FD.PE1D (offset 3418h, bit 16) is set, this link is not valid (returns 0). When FD.PE1D is cleared, this link is valid (returns 1). RP1BA—Root Port 1 Base Address Register Offset Address: 0128–012Fh Default Value: 00000000000E0000h Bit RO 64-bit Description Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #0. Reserved RP2D—Root Port 2 Descriptor Register Offset Address: 0130–0133h Default Value: 02xx0002h Attribute: Size: R/WO, RO 32-bit Bit Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 2h (root port #2). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. 15:2 354 Attribute: Size: 63:28 11:0 10.1.21 R/WO, RO 32-bit Bit 15:2 10.1.20 Attribute: Size: Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When RPC.PC (offset 0224h, bits 1:0) is ‘01’, ‘10’, or ‘11’, or FD.PE2D (offset 3418h, bit 17) is set, the link for this root port is not valid (return 0). When RPC.PC is ‘00’ and FD.PE2D is cleared, the link for this root port is valid (return 1). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.22 RP2BA—Root Port 2 Base Address Register Offset Address: 0138–013Fh Default Value: 00000000000E1000h Bit Description Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #1. Reserved RP3D—Root Port 3 Descriptor Register Offset Address: 0140–0143h Default Value: 03xx0002h Attribute: Size: R/WO, RO 32-bit Bit Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 3h (root port #3). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. 15:2 10.1.24 RO 64-bit 63:28 11:0 10.1.23 Attribute: Size: Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When RPC.PC (offset 0224h, bits 1:0) is ‘11’, or FD.PE3D (offset 3418h, bit 18) is set, the link for this root port is not valid (return 0). When RPC.PC is ‘00’, ‘01’, or “10’, and FD.PE3D is cleared, the link for this root port is valid (return 1). RP3BA—Root Port 3 Base Address Register Offset Address: 0148–014Fh Default Value: 00000000000E2000h Bit Attribute: Size: RO 64-bit Description 63:28 Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #2. 11:0 Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 355 Chipset Configuration Registers 10.1.25 RP4D—Root Port 4 Descriptor Register Offset Address: 0150–0153h Default Value: 04xx0002h Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 4h (root port #4). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When RPC.PC (offset 0224h, bits 1:0) is ‘10’ or ‘11’, or FD.PE4D (offset 3418h, bit 19) is set, the link for this root port is not valid (return 0). When RPC.PC is ‘00’ or ‘01’ and FD.PE4D is cleared, the link for this root port is valid (return 1). RP4BA—Root Port 4 Base Address Register Offset Address: 0158–015Fh Default Value: 00000000000E3000h Bit RO 64-bit Description Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #3. Reserved HDD—Intel® High Definition Audio Descriptor Register Offset Address: 0160–0163h Default Value: 0Fxx0002h Bit Attribute: Size: R/WO, RO 32-bit Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 15h (Intel® High Definition Audio). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. 15:2 356 Attribute: Size: 63:28 11:0 10.1.27 R/WO, RO 32-bit Bit 15:2 10.1.26 Attribute: Size: Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When FD.ZD (offset 3418h, bit 4) is set, the link to Intel High Definition Audio is not valid (return 0). When FD.ZD is cleared, the link to Intel High Definition Audio is valid (return 1). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.28 HDBA—Intel® High Definition Audio Base Address Register Offset Address: 0168–016Fh Default Value: 00000000000D8000h Bit Description Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #27. 14:12 Function Number (FN) — RO. Indicates the root port is on function #0. Reserved RP5D—Root Port 5 Descriptor Register Offset Address: 0170–0173h Default Value: 05xx0002h Attribute: Size: R/WO, RO 32-bit Bit Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 5h (root port #5). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. 15:2 10.1.30 RO 64-bit 63:28 11:0 10.1.29 Attribute: Size: Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When FD.PE5D (offset 3418h, bit 20) is set, the link for this root port is not valid (return 0). When FD.PE5D is cleared, the link for this root port is valid (return 1). RP5BA—Root Port 5 Base Address Register Offset Address: 0178–017Fh Default Value: 00000000000E4000h Bit Attribute: Size: RO 64-bit Description 63:28 Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #4. 11:0 Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 357 Chipset Configuration Registers 10.1.31 RP6D—Root Port 6 Descriptor Register Offset Address: 0180–0183h Default Value: 06xx0002h Description 31:24 Target Port Number (PN) — RO. Indicates the target port number is 6h (root port #6). 23:16 Target Component ID (TCID) — R/WO. This field returns the value of the ESD.CID (offset 0104h, bits 23:16) field programmed by platform BIOS, since the root port is in the same component as the RCRB. Reserved 1 Link Type (LT) — RO. Indicates that the link points to a root port. 0 Link Valid (LV) — RO. When RPC.PC2 (offset 0224h, bits 1:0) is ‘01’ or FD.PE6D (offset 3418h, bit 21) is set, the link for this root port is not valid (return 0). When RPC.PC is ‘00’ and FD.PE6D is cleared, the link for this root port is valid (return 1). RP6BA—Root Port 6 Base Address Register Offset Address: 0188–018Fh Default Value: 00000000000E5000h Bit RO 64-bit Description Reserved 27:20 Bus Number (BN) — RO. Indicates the root port is on bus #0. 19:15 Device Number (DN) — RO. Indicates the root port is on device #28. 14:12 Function Number (FN) — RO. Indicates the root port is on function #5. Reserved ILCL—Internal Link Capabilities List Register Offset Address: 01A0–01A3h Default Value: 00010006h Bit Attribute: Size: RO 32-bit Description 31:20 Next Capability Offset (NEXT) — RO. Indicates this is the last item in the list. 19:16 Capability Version (CV) — RO. Indicates the version of the capability structure. 15:0 358 Attribute: Size: 63:28 11:0 10.1.33 R/WO, RO 32-bit Bit 15:2 10.1.32 Attribute: Size: Capability ID (CID) — RO. Indicates this is capability for DMI. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.34 LCAP—Link Capabilities Register Offset Address: 01A4–01A7h Default Value: 00012841h Bit 10.1.35 R/WO, RO 32-bit Description 31:18 Reserved 17:15 (Desktop Only) Reserved 17:15 (Mobile Only) Attribute: Size: L1 Exit Latency (EL1) — RO. L1 is supported on DMI. 14:12 L0s Exit Latency (EL0) — R/WO. This field indicates that exit latency is 128 ns to less than 256 ns. 11:10 Active State Link PM Support (APMS) — R/WO. Indicates that L0s and L1 (Mobile only) are supported on DMI. 9:4 Maximum Link Width (MLW) — RO. Indicates the maximum link width is 4 ports. 3:0 Maximum Link Speed (MLS) — RO. Indicates the link speed is 2.5 Gb/s. LCTL—Link Control Register Offset Address: 01A8–01A9h Default Value: 0000h Bit 15:8 7 6:2 Attribute: Size: R/W 16-bit Description Reserved Extended Synch (ES) — R/W. When set, forces extended transmission of FTS ordered sets when exiting L0s prior to entering L0. Reserved Active State Link PM Control (APMC) — R/W. Indicates whether DMI should enter L0s. 1:0 00 = Disabled 01 = L0s entry enabled 10 = Reserved 11 = Reserved 10.1.36 LSTS—Link Status Register Offset Address: 01AA–01ABh Default Value: 0041h Bit 15:10 Attribute: Size: RO 16-bit Description Reserved 9:4 Negotiated Link Width (NLW) — RO. Negotiated link width is x4 (000100b). ICH9M may also indicate x2 (000010b), depending on (G)MCH configuration. 3:0 Link Speed (LS) — RO. Link is 2.5 Gb/s. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 359 Chipset Configuration Registers 10.1.37 CIR2 — Chipset Initialization Register 2 Offset Address: 01F4–01F7h Default Value: 00000000h Bit 31:0 10.1.38 CIR2 Field 1 — R/W. BIOS shall program to 86000040h CIR3 — Chipset Initialization Register 3 Bit 15:11 10:8 7:4 3 2 1:0 Attribute: Size: R/W 16-bit Description Reserved CIR3 Field 3 — R/W. BIOS must program this field to 110b. Reserved CIR3 Field 2 — R/W. BIOS must set this bit. Reserved CIR3 Field 1 — R/W. BIOS must program this field to 11b. BCR — Backbone Configuration Register Offset Address: 0220–0223h Default Value: 00000000h Bit 31:7 6 360 R/W 32-bit Description Offset Address: 01FC–01FDh Default Value: 0000h 10.1.39 Attribute: Size: Attribute: Size: R/W 32-bit Description Reserved BCR Field 2 — R/W. BIOS must set this bit. 5:3 Reserved 2:0 BCR Field 1 — R/W. BIOS program this field to 101b Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.40 RPC—Root Port Configuration Register Offset Address: 0224–0227h Default Value: 0000000yh (y = 00xxb) Bit 31:8 Attribute: Size: R/W, RO 32-bit Description Reserved High Priority Port Enable (HPE) — R/W. 7 0 = The high priority path is not enabled. 1 = The port selected by the HPP field in this register is enabled for high priority. It will be arbitrated above all other VC0 (including integrated VC0) devices. High Priority Port (HPP) — R/W. This controls which port is enabled for high priority when the HPE bit in this register is set. 111 = Reserved 110 = Reserved 6:4 101 = Port 6 100 = Port 5 101 = Port 4 010 = Port 3 001 = Port 2 000 = Port 1 3 Reserved Port Configuration2 (PC2) — R/W. This controls how the PCI bridges are organized in various modes of operation for Ports 5 and 6. 1 = Reserved 2 0 = 2 x1s, Port 5 (x1), Port 6 (x1) This bit is in the resume well and is only reset by RSMRST#. NOTE: Writing to this bit is for debug/testing only. This bit should be treated as Read Only and modifiable only through the GNT2# / GPIO53 pin strap. Port Configuration (PC) — R/W. This controls how the PCI bridges are organized in various modes of operation for Ports 1-4. For the following mappings, if a port is not shown, it is considered a x1 port with no connection. These bits represent the strap values of HDA_SDOUT (bit 1) and HDA_SYNC (bit 0) when TP[3] is not pulled low at the rising edge of PWROK. 11 = 1 x4, Port 1 (x4) 10 = Reserved 1:0 01 = Reserved (Desktop Only) 01 = 1x2 and 2x1s, Port 1 (x2), Port 3 (x1) and Port 4 (x1) (Mobile Only) 00 = 4 x1s, Port 1 (x1), Port 2 (x1), Port 3 (x1) and Port 4 (x1) These bits live in the resume well and are only reset by RSMRST#. NOTE: Writing to these bits is for debug/testing only. These bits should be treated as Read Only and modifiable only through the HDA_SDOUT and HDA_SYNC pin straps. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 361 Chipset Configuration Registers 10.1.41 DMIC—DMI Control Register Offset Address: 0234–0237h Default Value: 00000000h Bit 31:2 1:0 10.1.42 Attribute: Size: R/W 32-bit Description Reserved DMI Clock Gate Enable (DMICGEN) — R/W. BIOS must program this field to 11b. RPFN—Root Port Function Number and Hide for PCI Express* Root Ports Offset Address: 0238–023Ch Default Value: 00543210h Attribute: Size: R/WO, RO 32-bit For the PCI Express root ports, the assignment of a function number to a root port is not fixed. BIOS may re-assign the function numbers on a port by port basis. This capability will allow BIOS to disable/hide any root port and still have functions 0 thru N1 where N is the total number of enabled root ports. Port numbers will remain fixed to a physical root port. The existing root port Function Disable registers operate on physical ports (not functions). Port Configuration (1x4, 4x1, etc.) is not affected by the logical function number assignment and is associated with physical ports. Bit 31:24 23 22:20 19 18:16 15 14:12 11 362 Description Reserved Root Port 6 Config Hide (RP6CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Root Port 6 Function Number (RP6FN) — R/WO. These bits set the function number for PCI Express Root Port 6. This root port function number must be a unique value from the other root port function numbers Root Port 5 Config Hide (RP5CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Root Port 5 Function Number (RP5FN) — R/WO. These bits set the function number for PCI Express Root Port 5. This root port function number must be a unique value from the other root port function numbers Root Port 4 Config Hide (RP4CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Root Port 4 Function Number (RP4FN) — R/WO. These bits set the function number for PCI Express Root Port 4. This root port function number must be a unique value from the other root port function numbers Root Port 3 Config Hide (RP3CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers Bit 10:8 7 6:4 3 2:0 10.1.43 Description Root Port 3 Function Number (RP3FN) — R/WO. These bits set the function number for PCI Express Root Port 3. This root port function number must be a unique value from the other root port function numbers Root Port 2 Config Hide (RP2CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Root Port 2 Function Number (RP2FN) — R/WO. These bits set the function number for PCI Express Root Port 2. This root port function number must be a unique value from the other root port function numbers Root Port 1 Config Hide (RP1CH) — RW. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to ‘1’ the root port will not claim any downstream configuration transactions. Root Port 1 Function Number (RP1FN) — R/WO. These bits set the function number for PCI Express Root Port 1. This root port function number must be a unique value from the other root port function numbers FLRSTAT—FLR Pending Status Register Offset Address: 0290–0293h Default Value: 00000000h Bit 31:24 Attribute: Size: RO 32-bit Description Reserved. FLR Pending Status for D29:F7, EHCI #1 — R0. 23 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. 22:20 Reserved. FLR Pending Status for D29:F3, UHCI #6 — R0. 19 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. FLR Pending Status for D29:F2, UHCI #3 — R0. 18 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. FLR Pending Status for D29:F1, UHCI #2 — R0. 17 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. FLR Pending Status for D29:F0, UHCI #1 — R0. 16 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. FLR Pending Status for D26:F7, EHCI #2 — R0. 15 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. 14:11 Reserved. FLR Pending Status for D26:F2, UHCI #6 — R0. 10 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 363 Chipset Configuration Registers Bit Description FLR Pending Status for D26:F1, UHCI #5 — R0. 9 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. FLR Pending Status for D26:F0, UHCI #4 — R0. 8 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. 7:0 10.1.44 Reserved. CIR13—Chipset Initialization Register 13 Offset Address: 0F20h–0F23h Default Value: B2B477CCh Bit Description Reserved 19:16 CIR13 Field 1 — R/W. BIOS must program this field to 0101b. Reserved CIR5—Chipset Initialization Register 5 Offset Address: 1D40h–1D47h Default Value: 0000000000000000h Bit 63:1 0 10.1.46 R/W 32-bit 31:20 15:0 10.1.45 Attribute: Size: Attribute: Size: R/W 64-bit Description Reserved CIR5 Field 1 — R/W. BIOS must program this field to 1b. TRSR—Trap Status Register Offset Address: 1E00–1E03h Default Value: 00000000h Bit 31:4 Attribute: Size: R/WC, RO 32-bit Description Reserved Cycle Trap SMI# Status (CTSS) — R/WC. These bits are set by hardware when the corresponding Cycle Trap register is enabled and a matching cycle is received (and trapped). These bits are OR’ed together to create a single status bit in the Power Management register space. 3:0 Note that the SMI# and trapping must be enabled in order to set these bits. These bits are set before the completion is generated for the trapped cycle, thereby ensuring that the processor can enter the SMI# handler when the instruction completes. Each status bit is cleared by writing a 1 to the corresponding bit location in this register. 364 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.47 TRCR—Trapped Cycle Register Offset Address: 1E10–1E17h Default Value: 0000000000000000h Attribute: Size: RO 64-bit This register saves information about the I/O Cycle that was trapped and generated the SMI# for software to read. Bit 63:25 Description Reserved Read/Write# (RWI) — RO. 24 23:20 Reserved 19:16 Active-high Byte Enables (AHBE) — RO. This is the dword-aligned byte enables associated with the trapped cycle. A 1 in any bit location indicates that the corresponding byte is enabled in the cycle. 15:2 1:0 10.1.48 0 = Trapped cycle was a write cycle. 1 = Trapped cycle was a read cycle. Trapped I/O Address (TIOA) — RO. This is the dword-aligned address of the trapped cycle. Reserved TWDR—Trapped Write Data Register Offset Address: 1E18–1E1Fh Default Value: 0000000000000000h Attribute: Size: RO 64-bit This register saves the data from I/O write cycles that are trapped for software to read. Bit 63:32 31:0 Description Reserved Trapped I/O Data (TIOD) — RO. Dword of I/O write data. This field is undefined after trapping a read cycle. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 365 Chipset Configuration Registers 10.1.49 IOTRn — I/O Trap Register (0-3) Offset Address: 1E80–1E87h Register 0 1E88–1E8Fh Register 1 1E90–1E97h Register 2 1E98–1E9Fh Register 3 Default Value: 0000000000000000h Attribute: R/W Size: 64-bit These registers are used to specify the set of I/O cycles to be trapped and to enable this functionality. Bit 63:50 Description Reserved Read/Write Mask (RWM) — R/W. 49 0 = The cycle must match the type specified in bit 48. 1 = Trapping logic will operate on both read and write cycles. Read/Write# (RWIO) — R/W. 48 0 = Write 1 = Read NOTE: The value in this field does not matter if bit 49 is set. 47:40 Reserved 39:36 Byte Enable Mask (BEM) — R/W. A 1 in any bit position indicates that any value in the corresponding byte enable bit in a received cycle will be treated as a match. The corresponding bit in the Byte Enables field, below, is ignored. 35:32 Byte Enables (TBE) — R/W. Active-high dword-aligned byte enables. 31:24 Reserved 23:18 Address[7:2] Mask (ADMA) — R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the dword address, allowing for traps on address ranges up to 256 bytes in size. 17:16 Reserved 15:2 I/O Address[15:2] (IOAD) — R/W. dword-aligned address 1 Reserved 0 0 = Trapping and SMI# logic disabled. 1 = The trapping logic specified in this register is enabled. Trap and SMI# Enable (TRSE) — R/W. 366 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.50 DMC—DMI Miscellaneous Control Register Offset Address: 2010–2013h Default Value: 00000002h Bit 31:20 19 Attribute: Size: R/W 32-bit Description Reserved DMI Misc. Control Field 1 — R/W. BIOS shall always program this field as per the BIOS Specification. 0 = Disable DMI Power Savings. 1 = Enable DMI Power Savings. 18:12 Reserved 11:10 (Mobile Only) DMI Misc. Control Field 2 — R/W. BIOS shall set these bits to 11b 11:10 10.1.51 (Desktop Only) Reserved 9:0 Reserved CIR6—Chipset Initialization Register 6 Offset Address: 2024–2027h Default Value: 0B4030C0h Bit Attribute: Size: R/W 32-bit Description 31:24 (Mobile Only) Reserved 23:21 (Mobile Only) CIR6 Field 2 — R/W. BIOS must program this field to 011b. 20:8 (Mobile Only) Reserved 31:8 (Desktop Only) Reserved 7 6:0 CIR6 Field 1 — R/W. BIOS must clear this bit. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 367 Chipset Configuration Registers 10.1.52 CIR7—Chipset Initialization Register 7 Offset Address: 2034–2037h Default Value: B2B477CCh Bit Description Reserved 19:16 CIR7 Field 1 — R/W. BIOS must program this field to 0101b. Reserved CIR11—Chipset Initialization Register 11 (Mobile Only) Offset Address: 20C4–20C5h Default Value: 0000h Bit 15 14:0 10.1.54 Attribute: Size: R/W 16-bit Description CIR11 Field 1— R/W. BIOS may program this field to 1b. Reserved CIR12—Chipset Initialization Register 12 (Mobile Only) Offset Address: 20E4–20E5h Default Value: 0000h Bit 15 14:0 368 R/W 32-bit 31:20 15:0 10.1.53 Attribute: Size: Attribute: Size: R/W 16-bit Description CIR12 Field 1— R/W. BIOS may program this field to 1b. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.55 TCTL—TCO Configuration Register Offset Address: 3000–3000h Default Value: 00h Attribute: Size: Bit R/W 8-bit Description TCO IRQ Enable (IE) — R/W. 7 6:3 0 = TCO IRQ is disabled. 1 = TCO IRQ is enabled, as selected by the TCO_IRQ_SEL field. Reserved TCO IRQ Select (IS) — R/W. Specifies on which IRQ the TCO will internally appear. If not using the APIC, the TCO interrupt must be routed to IRQ9-11, and that interrupt is not sharable with the SERIRQ stream, but is shareable with other PCI interrupts. If using the APIC, the TCO interrupt can also be mapped to IRQ20-23, and can be shared with other interrupt. 2:0 000 001 010 011 100 101 110 111 = = = = = = = = IRQ 9 IRQ 10 IRQ 11 Reserved IRQ 20 (only IRQ 21 (only IRQ 22 (only IRQ 23 (only if if if if APIC APIC APIC APIC enabled) enabled) enabled) enabled) When setting the these bits, the IE bit should be cleared to prevent glitching. When the interrupt is mapped to APIC interrupts 9, 10 or 11, the APIC should be programmed for active-high reception. When the interrupt is mapped to APIC interrupts 20 through 23, the APIC should be programmed for active-low reception. 10.1.56 D31IP—Device 31 Interrupt Pin Register Offset Address: 3100–3103h Default Value: 03243200h Bit 31:28 Attribute: Size: R/W, RO 32-bit Description Reserved Thermal Throttle Pin (TTIP) — R/W. Indicates which pin the Thermal Throttle controller drives as its interrupt 27:24 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h–Fh = Reserved SATA Pin 2 (SIP2) — R/W. Indicates which pin the SATA controller 2 drives as its interrupt. 23:20 19:16 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h–Fh = Reserved Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 369 Chipset Configuration Registers Bit Description SM Bus Pin (SMIP) — R/W. Indicates which pin the SMBus controller drives as its interrupt. 15:12 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h–Fh = Reserved SATA Pin (SIP) — R/W. Indicates which pin the SATA controller drives as its interrupt. 11:8 10.1.57 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h–Fh = Reserved 7:4 Reserved 3:0 LPC Bridge Pin (LIP) — RO. Currently, the LPC bridge does not generate an interrupt, so this field is read-only and 0. D30IP—Device 30 Interrupt Pin Register Offset Address: 3104–3107h Default Value: 00000000h Bit 31:4 3:0 370 Attribute: Size: RO 32-bit Description Reserved PCI Bridge Pin (PIP) — RO. Currently, the PCI bridge does not generate an interrupt, so this field is read-only and 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.58 D29IP—Device 29 Interrupt Pin Register Offset Address: 3108–310Bh Default Value: 10004321h Bit Attribute: Size: R/W 32-bit Description EHCI Pin (EIP) — R/W. Indicates which pin the EHCI controller #1 drives as its interrupt. 0h = No interrupt 31:28 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved 27:16 Reserved UHCI #6 Pin (U3P) — R/W. Indicates which pin the UHCI controller #6 (Device 29 Function 3) drives as its interrupt, if controller exists 0h = No interrupt 1h = INTA# 15:12 2h = INTB# 3h = INTC# 4h = INTD# (Default) 5h-7h = Reserved NOTE: This field should be set to 0h when UHCI Controller #6 Remap bit (RCBA offset 35F0h:bit 0) is set to 0. UHCI #3 Pin (U2P) — R/W. Indicates which pin the UHCI controller #3 (Device 29 Function 2) drives as its interrupt. 0h = No interrupt 11:8 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-7h = Reserved UHCI #2 Pin (U1P) — R/W. Indicates which pin the UHCI controller #2 (Device 29 Function 1) drives as its interrupt. 0h = No interrupt 7:4 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-7h = Reserved UHCI #1 Pin (U0P) — R/W. Indicates which pin the UHCI controller #1 (Device 29 Function 0) drives as its interrupt. 0h = No interrupt 3:0 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 371 Chipset Configuration Registers 10.1.59 D28IP—Device 28 Interrupt Pin Register Offset Address: 310C–310Fh Default Value: 00214321h Bit 31:16 Attribute: Size: R/W 32-bit Description Reserved PCI Express* #6 Pin (P6IP) — R/W. Indicates which pin the PCI Express* port #6 drives as its interrupt. 23:20 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-7h = Reserved PCI Express #5 Pin (P5IP) — R/W. Indicates which pin the PCI Express port #5 drives as its interrupt. 19:16 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved PCI Express #4 Pin (P4IP) — R/W. Indicates which pin the PCI Express* port #4 drives as its interrupt. 15:12 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# 4h = INTD# (Default) 5h-7h = Reserved PCI Express #3 Pin (P3IP) — R/W. Indicates which pin the PCI Express port #3 drives as its interrupt. 11:8 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-7h = Reserved PCI Express #2 Pin (P2IP) — R/W. Indicates which pin the PCI Express port #2 drives as its interrupt. 7:4 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-7h = Reserved PCI Express #1 Pin (P1IP) — R/W. Indicates which pin the PCI Express port #1 drives as its interrupt. 3:0 372 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.60 D27IP—Device 27 Interrupt Pin Register Offset Address: 3110–3113h Default Value: 00000001h Bit 31:4 Attribute: Size: R/W 32-bit Description Reserved Intel® High Definition Audio Pin (ZIP) — R/W. Indicates which pin the Intel High Definition Audio controller drives as its interrupt. 0h = No interrupt 3:0 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 373 Chipset Configuration Registers 10.1.61 D26IP—Device 26 Interrupt Pin Register Offset Address: 3114–3117h Default Value: 30000321h Bit Attribute: Size: R/W 32-bit Description EHCI #2 Pin (E2IP) — R/W. Indicates which pin the EHCI controller #2 drives as its interrupt: 31:28 27:12 0h = No Interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-Fh = Reserved Reserved UHCI #6 Pin (U2P) — R/W. Indicates which pin UHCI controller #6 (Device 26 Function 2) drives as its interrupt, if controller exists. 11:8 0h = No Interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-Fh = Reserved NOTE: This field should be set to 0h when UHCI Controller #6 Remap bit (RCBA offset 35F0h:bit 0) is set to 1. UHCI #5 Pin (U1P) — R/W. Indicates which pin UHCI controller #5 (Device 26 Function 1), drives as its interrupt. 7:4 0h = No Interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-Fh = Reserved UHCI #4 Pin (U0P) — R/W. Indicates which pin UHCI controller #4 (Device 26 Function 0), drives as its interrupt. 3:0 374 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.62 D25IP—Device 25 Interrupt Pin Register Offset Address: 3118–311Bh Default Value: 00000001h Bit 31:4 Attribute: Size: R/W 32-bit Description Reserved GBE LAN Pin (LIP) — R/W. Indicates which pin the internal GbE LAN controller drives as its interrupt 3:0 10.1.63 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved D31IR—Device 31 Interrupt Route Register Offset Address: 3140–3141h Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR) — R/W. Indicates which physical pin on the Intel® ICH is connected to the INTD# pin reported for device 31 functions. 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 31 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 375 Chipset Configuration Registers Bit Description Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 31 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 31 functions. 2:0 10.1.64 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# (Default) PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# D30IR—Device 30 Interrupt Route Register Offset Address: 3142–3143h Default Value: 0000h Bit 15:0 376 Attribute: Size: RO 16-bit Description Reserved. No interrupts generated from Device 30. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.65 D29IR—Device 29 Interrupt Route Register Offset Address: 3144–3145h Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR) — R/W. Indicates which physical pin on the Intel® ICH is connected to the INTD# pin reported for device 29 functions. 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 29 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 29 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 29 functions. 2:0 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# (Default) PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 377 Chipset Configuration Registers 10.1.66 D28IR—Device 28 Interrupt Route Register Offset Address: 3146–3147h Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR) — R/W. Indicates which physical pin on the Intel® ICH is connected to the INTD# pin reported for device 28 functions. 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 28 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 28 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 28 functions. 2:0 378 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# (Default) PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.67 D27IR—Device 27 Interrupt Route Register Offset Address: 3148–3149h Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR) — R/W. Indicates which physical pin on the Intel® ICH is connected to the INTD# pin reported for device 27 functions. 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 27 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 27 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 27 functions. 2:0 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# (Default) PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 379 Chipset Configuration Registers 10.1.68 D26IR—Device 26 Interrupt Route Register Offset Address: 314C–314Dh Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR) — R/W. Indicates which physical pin on the ICH is connected to the INTD# pin reported for device 26 functions: 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 26 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 26 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 26 functions. 0h = PIRQA# (Default) 2:0 380 1h 2h 3h 4h 5h 6h 7h = = = = = = = PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.69 D25IR—Device 25 Interrupt Route Register Offset Address: 3150–3151h Default Value: 3210h Bit 15 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR): — R/W. Indicates which physical pin on the ICH is connected to the INTD# pin reported for device 25 functions: 14:12 11 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# PIRQD# (Default) PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt C Pin Route (ICR) — R/W. Indicates which physical pin on the ICH is connected to the INTC# pin reported for device 25 functions. 10:8 7 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# PIRQC# (Default) PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt B Pin Route (IBR) — R/W. Indicates which physical pin on the ICH is connected to the INTB# pin reported for device 25 functions. 6:4 3 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# PIRQB# (Default) PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Reserved Interrupt A Pin Route (IAR) — R/W. Indicates which physical pin on the ICH is connected to the INTA# pin reported for device 25 functions. 2:0 0h 1h 2h 3h 4h 5h 6h 7h = = = = = = = = PIRQA# (Default) PIRQB# PIRQC# PIRQD# PIRQE# PIRQF# PIRQG# PIRQH# Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 381 Chipset Configuration Registers 10.1.70 OIC—Other Interrupt Control Register Offset Address: 31FF–31FFh Default Value: 00h Attribute: Size: R/W 8-bit Bit Description 7:4 APIC Range Select (ASEL) — R/W.These bits define address bits 15:12 for the IOxAPIC range. The default value of 0h enables compatibility with prior ICH products as an initial value. This value must not be changed unless the IOxAPIC Enable bit is cleared. 3:2 Reserved Coprocessor Error Enable (CEN) — R/W. 1 0 = FERR# will not generate IRQ13 nor IGNNE#. 1 = If FERR# is low, the Intel® ICH9 generates IRQ13 internally and holds it until an I/O port F0h write. It will also drive IGNNE# active. APIC Enable (AEN) — R/W. 0 10.1.71 0 = The internal IOxAPIC is disabled. 1 = Enables the internal IOxAPIC and its address decode. NOTE: SW should read this register after modifying APIC enable bit prior to access to the IOxAPIC address range. SBEMC3—Scheduled Break Event C3 Exit Latency (Mobile Only) Offset Address: 3300–3303h Default Value: 00000000h Bit 31:23 22:16 15 14:8 7 6:0 382 Attribute: Size: R/W 32-bit Description Reserved. Present State C3 Future State C3 Exit Latency (C3C3EL) — R/W. Sets exit latency if present and future C-state is C3. Reserved. Present State C2 Future State C3 Exit Latency (C2C3EL) — R/W. Sets exit latency if present c-state is C2 and future C-state is C3. Reserved. Present State C0 Future State C3 Exit Latency (C0C3EL) — R/W. Sets exit latency if present c-state is C0 and future C-state is C3. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.72 SBEMC4—Scheduled Break Event C4 Exit Latency (Mobile Only) Offset Address: 3304–3307h Default Value: 00000000h Bit 31 30:24 22:16 15 14:8 7 6:0 10.1.73 Attribute: Size: R/W 32-bit Description Reserved. Present State C4 Future State C4 Exit Latency (C4C4EL) — R/W. Sets exit latency if present and future c-state is C4. Present State C3 Future State C4 Exit Latency (C3C4EL) — R/W. Sets exit latency if present c-state is C3 and future C-state is C4. Reserved. Present State C2 Future State C4 Exit Latency (C2C4EL) — R/W. Sets exit latency if present c-state is C2 and future C-state is C4. Reserved. Present State C0 Future State C4 Exit Latency (C0C4EL) — R/W. Sets exit latency if present c-state is C0 and future C-state is C4. RC—RTC Configuration Register Offset Address: 3400–3403h Default Value: 00000000h Bit Attribute: Size: R/W, R/WLO 32-bit Description 31:5 Reserved Upper 128 Byte Lock (UL) — R/WLO. 4 0 = Bytes not locked. 1 = Bytes 38h-3Fh in the upper 128-byte bank of RTC RAM are locked and cannot be accessed. Writes will be dropped and reads will not return any ensured data. Bit reset on system reset. Lower 128 Byte Lock (LL) — R/WLO. 3 0 = Bytes not locked. 1 = Bytes 38h-3Fh in the lower 128-byte bank of RTC RAM are locked and cannot be accessed. Writes will be dropped and reads will not return any ensured data. Bit reset on system reset. Upper 128 Byte Enable (UE) — R/W. 2 1:0 0 = Bytes locked. 1 = The upper 128-byte bank of RTC RAM can be accessed. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 383 Chipset Configuration Registers 10.1.74 HPTC—High Precision Timer Configuration Register Offset Address: 3404–3407h Default Value: 00000000h Bit 31:8 Attribute: Size: R/W 32-bit Description Reserved Address Enable (AE) — R/W. 7 6:2 0 = Address disabled. 1 = The Intel® ICH9 will decode the High Precision Timer memory address range selected by bits 1:0 below. Reserved Address Select (AS) — R/W. This 2-bit field selects 1 of 4 possible memory address ranges for the High Precision Timer functionality. The encodings are: 1:0 00 = FED0_0000h – FED0_03FFh 01 = FED0_1000h – FED0_13FFh 10 = FED0_2000h – FED0_23FFh 11 = FED0_3000h – FED0_33FFh 384 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.75 GCS—General Control and Status Register Offset Address: 3410–3413h Attribute: Default Value: 00000yy0h (yy = xx0000x0b)Size: Bit 31:13 R/W, R/WLO 32-bit Description Reserved. Function Level Reset Capability Structure Select (FLRCSSEL) — R/W. 12 0 = Function Level Reset (FLR) will utilize the standard capability structure with unique capability ID assigned by PCISIG. 1 = Vendor Specific Capability Structure is selected for FLR. Boot BIOS Straps (BBS) — R/W. This field determines the destination of accesses to the BIOS memory range. The default values for these bits represent the strap values of GNT0# (bit 11) at the rising edge of PWROK and SPI_CS1#/GPIO58 (Desktop Only) /CLGPIO6 (Digital Office Only) (bit 10) at the rising edge of CLPWROK. Bits 11:10 0xb 11:10 Description SPI 10b PCI 11b LPC When PCI is selected, the top 16MB of memory below 4GB (FF00_0000h to FFFF_FFFFh) is accepted by the primary side of the PCI P2P bridge and forwarded to the PCI bus. This allows systems with corrupted or unprogrammed flash to boot from a PCI device. The PCI-to-PCI bridge Memory Space Enable bit does not need to be set (nor any other bits) in order for these cycles to go to PCI. Note that BIOS decode range bits and the other BIOS protection bits have no effect when PCI is selected. This functionality is intended for debug/testing only. When SPI or LPC is selected, the range that is decoded is further qualified by other configuration bits described in the respective sections. The value in this field can be overwritten by software as long as the BIOS Interface Lock-Down (bit 0) is not set. NOTE: Booting to PCI is intended for debug/testing only. Boot BIOS Destination Select to LPC/PCI by functional strap or via Boot BIOS Destination Bit will not affect SPI accesses initiated by Management Engine or Integrated GbE LAN. Server Error Reporting Mode (SERM) — R/W. 9 8:7 0 = The Intel® ICH9 is the final target of all errors. The (G)MCH sends a messages to the ICH for the purpose of generating NMI. 1 = The (G)MCH is the final target of all errors from PCI Express* and DMI. In this mode, if the ICH9 detects a fatal, non-fatal, or correctable error on DMI or its downstream ports, it sends a message to the (G)MCH. If the ICH9 receives an ERR_* message from the downstream port, it sends that message to the (G)MCH. Reserved FERR# MUX Enable (FME) — R/W. This bit enables FERR# to be a processor break event indication. 6 0 = Disabled. 1 = The ICH9 examines FERR# during a C2, C3, or C4 state as a break event. See Chapter 5.13.5 for a functional description. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 385 Chipset Configuration Registers Bit 5 Description No Reboot (NR) — R/W. This bit is set when the “No Reboot” strap (SPKR pin on ICH9) is sampled high on PWROK. This bit may be set or cleared by software if the strap is sampled low but may not override the strap when it indicates “No Reboot”. 0 = System will reboot upon the second timeout of the TCO timer. 1 = The TCO timer will count down and generate the SMI# on the first timeout, but will not reboot on the second timeout. Alternate Access Mode Enable (AME) — R/W. 4 3 0 = Disabled. 1 = Alternate access read only registers can be written, and write only registers can be read. Before entering a low power state, several registers from powered down parts may need to be saved. In the majority of cases, this is not an issue, as registers have read and write paths. However, several of the ISA compatible registers are either read only or write only. To get data out of write-only registers, and to restore data into read-only registers, the ICH implements an alternate access mode. For a list of these registers see Section 5.13.10. Shutdown Policy Select (SPS) — R/W. When cleared (default), the ICH9 will drive INIT# in response to the shutdown Vendor Defined Message (VDM). When set to 1, ICH9 will treat the shutdown VDM similar to receiving a CF9h I/O write with data value06h, and will drive PLTRST# active. Reserved Page Route (RPR) — R/W. Determines where to send the reserved page registers. These addresses are sent to PCI or LPC for the purpose of generating POST codes. The I/O addresses modified by this field are: 80h, 84h, 85h, 86h, 88h, 8Ch, 8Dh, and 8Eh. 2 0 = Writes will be forwarded to LPC, shadowed within the ICH, and reads will be returned from the internal shadow 1 = Writes will be forwarded to PCI, shadowed within the ICH, and reads will be returned from the internal shadow. Note, if some writes are done to LPC/PCI to these I/O ranges, and then this bit is flipped, such that writes will now go to the other interface, the reads will not return what was last written. Shadowing is performed on each interface. The aliases for these registers, at 90h, 94h, 95h, 96h, 98h, 9Ch, 9Dh, and 9Eh, are always decoded to LPC. 1 Reserved BIOS Interface Lock-Down (BILD) — R/WLO. 0 386 0 = Disabled. 1 = Prevents BUC.TS (offset 3414, bit 0) and GCS.BBS (offset 3410h, bits 11:10) from being changed. This bit can only be written from 0 to 1 once. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.76 BUC—Backed Up Control Register Offset Address: 3414–3414h Default Value: 0000000xb Attribute: Size: R/W 8-bit All bits in this register are in the RTC well and only cleared by RTCRST# Bit Description 7:6 Reserved LAN Disable — R/W. 5 0 = LAN is Enabled 1 = LAN is Disabled. This bit is locked by the Function Disable SUS Well Lockdown register. Once locked this bit can not be changed by software. Daylight Savings Override (SDO) — R/W. 4 3 0 = Daylight Savings is Enabled. 1 = The DSE bit in RTC Register B is set to Read-only with a value of 0 to disable daylight savings. Reserved CPU BIST Enable (CBE) — R/W. This bit is in the resume well and is reset by RSMRST#, but not PLTRST# nor CF9h writes. 2 1 0 = Disabled. 1 = The INIT# signals will be driven active when CPURST# is active. INIT# and INIT3_3V# will go inactive with the same timings as the other processor interface signals (hold time after CPURST# inactive). Reserved Top Swap (TS) — R/W. 0 0 = Intel® ICH9 will not invert A16. 1 = ICH9 will invert A16 for cycles going to the BIOS space (but not the feature space) in the FWH. If ICH is strapped for Top-Swap (GNT3# is low at rising edge of PWROK), then this bit cannot be cleared by software. The strap jumper should be removed and the system rebooted. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 387 Chipset Configuration Registers 10.1.77 FD—Function Disable Register Offset Address: 3418–341Bh Default Value: See bit description Attribute: Size: R/W 32-bit The UHCI functions must be disabled from highest function number to lowest within each PCI device (Device 29 or Device 26). For example, if only two UHCIs are wanted on Device 29, software must disable UHCI #3 (UD3 bit set). When disabling UHCIs, the EHCI Structural Parameters Registers must be updated with coherent information in “Number of Companion Controllers” and “N_Ports” fields. When disabling a function, only the configuration space is disabled. Software must ensure that all functionality within a controller that is not desired (such as memory spaces, I/O spaces, and DMA engines) is disabled prior to disabling the function. When a function is disabled, software must not attempt to re-enable it. A disabled function can only be re-enabled by a platform reset. Bit 31:26 Description Reserved Serial ATA Disable 2 (SAD2) — R/W. Default is 0. 25 0 = The SATA controller #2 (D31:F5) is enabled. 1 = The SATA controller #2 (D31:F5) is disabled. Thermal Throttle Disable (TTD) — R/W. Default is 0. 24 23:22 21 20 0 = Thermal Throttle is enabled. 1 = Thermal Throttle is disabled. Reserved PCI Express* 6 Disable (PE6D) — R/W. Default is 0. When disabled, the link for this port is put into the “link down” state. 0 = PCI Express* port #6 is enabled. 1 = PCI Express port #6 is disabled. PCI Express 5 Disable (PE5D) — R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #5 is enabled. 1 = PCI Express port #5 is disabled. PCI Express 4 Disable (PE4D) — R/W. Default is 0. When disabled, the link for this port is put into the “link down” state. 19 0 = PCI Express port #4 is enabled. 1 = PCI Express port #4 is disabled. NOTE: This bit must be set when Port 1 is configured as a x4. PCI Express 3 Disable (PE3D) — R/W. Default is 0. When disabled, the link for this port is put into the link down state. 18 0 = PCI Express port #3 is enabled. 1 = PCI Express port #3 is disabled. NOTE: This bit must be set when Port 1 is configured as a x4. PCI Express 2 Disable (PE2D) — R/W. Default is 0. When disabled, the link for this port is put into the link down state. 17 388 0 = PCI Express port #2 is enabled. 1 = PCI Express port #2 is disabled. NOTE: This bit must be set when Port 1 is configured as a x4 or a x2. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers Bit 16 Description PCI Express 1 Disable (PE1D) — R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #1 is enabled. 1 = PCI Express port #1 is disabled. EHCI #1 Disable (EHCI1D) — R/W. Default is 0. 15 0 = The EHCI #1 is enabled. 1 = The EHCI #1 is disabled. LPC Bridge Disable (LBD) — R/W. Default is 0. 0 = The LPC bridge is enabled. 1 = The LPC bridge is disabled. Unlike the other disables in this register, the following additional spaces will no longer be decoded by the LPC bridge: 14 • • • · Memory cycles below 16 MB (1000000h) · I/O cycles below 64 KB (10000h) · The Internal I/OxAPIC at FEC0_0000 to FECF_FFFF Memory cycles in the LPC BIOS range below 4 GB will still be decoded when this bit is set, but the aliases at the top of 1 MB (the E and F segment) no longer will be decoded. EHCI #2 Disable (EHCI2D) — R/W. Default is 0. 13 0 = The EHCI #2 is enabled. 1 = The EHCI #2 is disabled. Note: When this bit is set, the UHCI #5 function is not available and the UHCI #4 must be disabled by setting bit 11 in this register. UHCI #5 Disable (U5D) — R/W. Default is 0 12 0 = The UHCI #5 is enabled. 1 = The UHCI #5 is disabled. When the EHCI #2 Device Disable (EHCI2D) is set, this bit is a don’t care UHCI #4 Disable (U4D) — R/W. Default is 0. 11 0 = The 4th UHCI (ports 6 and 7) is enabled. 1 = The 4th UHCI (ports 6 and 7) is disabled. Note that UHCI #4 must be disabled when EHCI #2 is disabled with bit 13 in this register. UHCI #3 Disable (U3D) — R/W. Default is 0. 10 0 = The 3rd UHCI (ports 4 and 5) is enabled. 1 = The 3rd UHCI (ports 4 and 5) is disabled. UHCI #2 Disable (U2D) — R/W. Default is 0. 9 0 = The 2nd UHCI (ports 2 and 3) is enabled. 1 = The 2nd UHCI (ports 2 and 3) is disabled. UHCI #1 Disable (U1D) — R/W. Default is 0. 8 0 = The 1st UHCI (ports 0 and 1) is enabled. 1 = The 1st UHCI (ports 0 and 1) is disabled. UHCI #6 Disable (U6D) — R/W. Default is 0. 7 6:5 0 = The 6th UHCI (ports 10 and 11) is enabled. 1 = The 6th UHCI (ports 10 and 11) is disabled. Reserved Intel® High Definition Audio Disable (HDAD) — R/W. Default is 0. 4 0 = The Intel High Definition Audio controller is enabled. 1 = The Intel High Definition Audio controller is disabled and its PCI configuration space is not accessible. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 389 Chipset Configuration Registers Bit Description SM Bus Disable (SD) — R/W. Default is 0. 3 0 = The SM Bus controller is enabled. 1 = The SM Bus controller is disabled. In ICH5 and previous, this also disabled the I/ O space. In ICH9, it only disables the configuration space. Serial ATA Disable 1 (SAD1) — R/W. Default is 0. 10.1.78 2 0 = The SATA controller #1 (D31:F2) is enabled. 1 = The SATA controller #1 (D31:F2) is disabled. 1 Reserved 0 BIOS must set this bit to 1b. CG—Clock Gating Offset Address: 341C–341Fh Default Value: 00000000h Bit Attribute: Size: R/W 32-bit Description Legacy (LPC) Dynamic Clock Gate Enable — R/W. 31 0 = Legacy Dynamic Clock Gating is Disabled 1 = Legacy Dynamic Clock Gating is Enabled 30 Reserved USB UHCI Dynamic Clock Gate Enable — R/W. 29:28 0 = USB UHCI Dynamic Clock Gating is Disabled 1 = USB UHCI Dynamic Clock Gating is Enabled 0 = Reserved 1 = Reserved 27 (Desktop Only) SATA Port 3 Dynamic Clock Gate Enable — R/W. 26 (Desktop Only) SATA Port 2 Dynamic Clock Gate Enable — R/W. 27:26 (Mobile Only) 0 = SATA Port 3 Dynamic Clock Gating is Disabled 1 = SATA Port 3 Dynamic Clock Gating is Enabled 0 = SATA Port 2 Dynamic Clock Gating is Disabled 1 = SATA Port 2 Dynamic Clock Gating is Enabled Reserved SATA Port 1 Dynamic Clock Gate Enable — R/W. 25 0 = SATA Port 1 Dynamic Clock Gating is Disabled 1 = SATA Port 1 Dynamic Clock Gating is Enabled SATA Port 0 Dynamic Clock Gate Enable — R/W. 24 0 = SATA Port 0 Dynamic Clock Gating is Disabled 1 = SATA Port 0 Dynamic Clock Gating is Enabled LAN Static Clock Gating Enable (LANSCGE) — R/W. 23 390 0 = LAN Static Clock Gating is Disabled 1 = LAN Static Clock Gating is Enabled when the LAN Disable bit is set in the Backed Up Control RTC register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers Bit Description High Definition Audio Dynamic Clock Gate Enable — R/W. 22 0 = High Definition Audio Dynamic Clock Gating is Disabled 1 = High Definition Audio Dynamic Clock Gating is Enabled High Definition Audio Static Clock Gate Enable — R/W. 21 0 = High Definition Audio Static Clock Gating is Disabled 1 = High Definition Audio Static Clock Gating is Enabled USB EHCI Static Clock Gate Enable — R/W. 20 0 = USB EHCI Static Clock Gating is Disabled 1 = USB EHCI Static Clock Gating is Enabled USB EHCI Dynamic Clock Gate Enable — R/W. 19 0 = USB EHCI Dynamic Clock Gating is Disabled 1 = USB EHCI Dynamic Clock Gating is Enabled SATA Port 5 Dynamic Clock Gate Enable — R/W. 18 0 = SATA Port 5 Dynamic Clock Gating is Disabled 1 = SATA Port 5 Dynamic Clock Gating is Enabled SATA Port 4 Dynamic Clock Gate Enable — R/W. 17 0 = SATA Port 4 Dynamic Clock Gating is Disabled 1 = SATA Port 4 Dynamic Clock Gating is Enabled 16 0 = PCI Dynamic Gating is Disabled 1 = PCI Dynamic Gating is Enabled PCI Dynamic Gate Enable — R/W. 15:6 Reserved SMBus Clock Gating Enable (SMBCGEN) — R/W. 5 0 = SMBus Clock Gating is Disabled. 1 = SMBus Clock Gating is Enabled. PCI Express* RX Clock Gating Enable (PRXCGEN) — R/W. 4 0 = AFE RX Clock Gating is Disabled 1 = AFE RX Clock Gating is Enabled whenever all PCIe ports RX are in squelch DMI and PCI Express* RX Dynamic Clock Gate Enable — R/W. 3 0 = DMI and PCI Express root port RX Dynamic Clock Gating is Disabled 1 = DMI and PCI Express root port RX Dynamic Clock Gating is Enabled 2 0 = PCI Express root port TX Dynamic Clock Gating is Disabled 1 = PCI Express root port TX Dynamic Clock Gating is Enabled PCI Express TX Dynamic Clock Gate Enable — R/W. DMI TX Dynamic Clock Gate Enable — R/W. 1 0 = DMI TX Dynamic Clock Gating is Disabled 1 = DMI TX Dynamic Clock Gating is Enabled PCI Express Root Port Static Clock Gate Enable — R/W. 0 0 = PCI Express root port Static Clock Gating is Disabled 1 = PCI Express root port Static Clock Gating is Enabled Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 391 Chipset Configuration Registers 10.1.79 FDSW—Function Disable SUS Well Offset Address: 3420h Default Value: 00h Bit Attribute: Size: R/W 8-bit Description Function Disable SUS Well Lockdown (FDSWL)— R/W 7 6:0 10.1.80 0 = FDSW registers are not locked down 1 = FDSW registers are locked down NOTE: This bit must be set when Intel® Active Management Technology is enabled. Reserved CIR8—Chipset Initialization Register 8 Offset Address: 3430-3433h Default Value: 00000000h Bit 10.1.81 R/W 32-bit Description 7:2 Reserved 1:0 CIR8 Field 1 — R/W. BIOS must program this field to 10b. CIR9—Chipset Initialization Register 9 Offset Address: 350Ch–350Fh Default Value: 00000000h Bit Attribute: Size: R/W 32-bit Description 31:28 Reserved 27:26 CIR9 Field 1 — R/W. BIOS must program this field to 10b. 25:0 10.1.82 Attribute: Size: Reserved PPO - Port Power Off Offset Address: 3524–3525h Default Value: 0000h Bit 15:12 Attribute: Size: R/W 16-bit Description Reserved USB Port Power Off— R/W 1 = The corresponding EHCI and UHCI ports are electrically disconnected in this mode. 11:0 392 Warning: The platform must ensure that the powered off ports are not routed to any internal USB header or external USB connector. The ICH provides pull-down termination resistors. This register can not be written when the USB Per-Port Registers Write Enable bit (UPRWC register, PMBASE + 3C, bit 1) is 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Chipset Configuration Registers 10.1.83 CIR10 - Chipset Initialization Register 10 Offset Address: 352C–352Fh Default Value: 0008C008h Bit R/W 32-bit Description 32:18 Reserved 17:16 CIR10 Field 1— R/W. BIOS must program this field to 11b. 15:0 10.1.84 Attribute: Size: Reserved MAP - Remap Control Register Offset Address: 35F0-35F3h Default Value: 00000000h Bit 31:01 Attribute: Size: R/WO 32-bit Description Reserved UHCI Controller # 6 Remap — R/WO 1 = UHCI Controller #6 is mapped to Device 29 Function 3 0 0 = UHCI Controller #6 is mapped to Device 26 Function 2 Note: When this bit is set, SW should reprogram the HCSPARAMS register (Section 17.2.1.3) to reflect the correct value for N_CC (bits 15:12) and N_Ports (bits 3:0) in each EHCI controller. §§ Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 393 Chipset Configuration Registers 394 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11 PCI-to-PCI Bridge Registers (D30:F0) The ICH9 PCI bridge resides in PCI Device 30, Function 0 on bus #0. This implements the buffering and control logic between PCI and the backbone. The arbitration for the PCI bus is handled by this PCI device. 11.1 PCI Configuration Registers (D30:F0) Note: Address locations that are not shown should be treated as Reserved (see Section 9.2 for details). . Table 11-1. PCI Bridge Register Address Map (PCI-PCI—D30:F0) (Sheet 1 of 2) Offset 00h–01h 02h–03h Mnemonic VID DID Register Name Default Type Vendor Identification 8086h RO Device Identification See register description RO 04h–05h PCICMD PCI Command 0000h R/W, RO 06h–07h PSTS PCI Status 0010h R/WC, RO 08h RID Revision Identification See register description RO 09h–0Bh CC Class Code 060401h RO 0Dh PMLT Primary Master Latency Timer 00h RO 0Eh HEADTYP Header Type 01h RO 18h–1Ah BNUM Bus Number 000000h RO 1Bh SMLT Secondary Master Latency Timer 00h R/W 1Ch–1Dh IOBASE_LIMIT I/O Base and Limit 0000h R/W, RO 1Eh–1Fh SECSTS Secondary Status 0280h R/WC, RO 20h–23h MEMBASE_LIMIT Memory Base and Limit 00000000h R/W 24h–27h PREF_MEM_BASE _LIMIT Prefetchable Memory Base and Limit 00010001h R/W, RO 28h–2Bh PMBU32 Prefetchable Memory Upper 32 Bits 00000000h R/W 2Ch–2Fh PMLU32 Prefetchable Memory Limit Upper 32 Bits 00000000h R/W 34h CAPP Capability List Pointer 50h RO 3Ch–3Dh INTR Interrupt Information 0000h R/W, RO 3Eh–3Fh BCTRL Bridge Control 0000h R/WC, RO, R/W 40h–41h SPDH Secondary PCI Device Hiding 0000h R/W, RO 44h–47h DTC Delayed Transaction Control 00000000h R/W 48h–4Bh BPS Bridge Proprietary Status 00000000h R/WC, RO Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 395 PCI-to-PCI Bridge Registers (D30:F0) Table 11-1. PCI Bridge Register Address Map (PCI-PCI—D30:F0) (Sheet 2 of 2) Offset 11.1.1 Mnemonic Register Name 4Ch–4Fh BPC Bridge Policy Configuration 50–51h SVCAP Subsystem Vendor Capability Pointer 54h–57h SVID Subsystem Vendor IDs Bit 15:0 00001200h R/W RO 000Dh RO 00000000 R/WO Attribute: Size: RO 16 bits Description Vendor ID — RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h. DID— Device Identification Register (PCI-PCI—D30:F0) Offset Address: 02h–03h Default Value: See bit description 396 Type VID— Vendor Identification Register (PCI-PCI—D30:F0) Offset Address: 00h–01h Default Value: 8086h 11.1.2 Default Attribute: Size: RO 16 bits Bit Description 15:0 Device ID — RO.This is a 16-bit value assigned to the PCI bridge. Refer to the Intel® I/O Controller Hub (ICH9) Family Specification Update for the value of the Device ID Register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.3 PCICMD—PCI Command (PCI-PCI—D30:F0) Offset Address: 04h–05h Default Value: 0000h Bit 15:11 Attribute: Size: R/W, RO 16 bits Description Reserved 10 Interrupt Disable (ID) — RO. Hardwired to 0. The PCI bridge has no interrupts to disable 9 Fast Back to Back Enable (FBE) — RO. Hardwired to 0, per the PCI Express* Base Specification, Revision 1.0a. SERR# Enable (SERR_EN) — R/W. 8 7 0 = Disable. 1 = Enable the ICH9 to generate an NMI (or SMI# if NMI routed to SMI#) when the D30:F0 SSE bit (offset 06h, bit 14) is set. Wait Cycle Control (WCC) — RO. Hardwired to 0, per the PCI Express* Base Specification, Revision 1.0a. Parity Error Response (PER) — R/W. 6 0 = The ICH9 ignores parity errors on the PCI bridge. 1 = The ICH9 will set the SSE bit (D30:F0, offset 06h, bit 14) when parity errors are detected on the PCI bridge. 5 VGA Palette Snoop (VPS) — RO. Hardwired to 0, per the PCI Express* Base Specification, Revision 1.0a. 4 Memory Write and Invalidate Enable (MWE) — RO. Hardwired to 0, per the PCI Express* Base Specification, Revision 1.0a 3 Special Cycle Enable (SCE) — RO. Hardwired to 0, per the PCI Express* Base Specification, Revision 1.0a and the PCI- to-PCI Bridge Specification. Bus Master Enable (BME) — R/W. 2 1 0 11.1.4 0 = Disable 1 = Enable. Allows the PCI-to-PCI bridge to accept cycles from PCI. Memory Space Enable (MSE) — R/W. Controls the response as a target for memory cycles targeting PCI. 0 = Disable 1 = Enable I/O Space Enable (IOSE) — R/W. Controls the response as a target for I/O cycles targeting PCI. 0 = Disable 1 = Enable PSTS—PCI Status Register (PCI-PCI—D30:F0) Offset Address: 06h–07h Default Value: 0010h Note: Attribute: Size: R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 397 PCI-to-PCI Bridge Registers (D30:F0) Bit Description Detected Parity Error (DPE) — R/WC. 15 0 = Parity error Not detected. 1 = Indicates that the ICH9 detected a parity error on the internal backbone. This bit gets set even if the Parity Error Response bit (D30:F0:04 bit 6) is not set. Signaled System Error (SSE) — R/WC. Several internal and external sources of the bridge can cause SERR#. The first class of errors is parity errors related to the backbone. The PCI bridge captures generic data parity errors (errors it finds on the backbone) as well as errors returned on backbone cycles where the bridge was the master. If either of these two conditions is met, and the primary side of the bridge is enabled for parity error response, SERR# will be captured as shown below. As with the backbone, the PCI bus captures the same sets of errors. The PCI bridge captures generic data parity errors (errors it finds on PCI) as well as errors returned on PCI cycles where the bridge was the master. If either of these two conditions is met, and the secondary side of the bridge is enabled for parity error response, SERR# will be captured as shown below. 14 The final class of errors is system bus errors. There are three status bits associated with system bus errors, each with a corresponding enable. The diagram capturing this is shown below. After checking for the three above classes of errors, an SERR# is generated, and PSTS.SSE logs the generation of SERR#, if CMD.SEE (D30:F0:04, bit 8) is set, as shown below. Received Master Abort (RMA) — R/WC. 13 398 0 = No master abort received. 1 = Set when the bridge receives a master abort status from the backbone. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) Bit Description Received Target Abort (RTA) — R/WC. 12 0 = No target abort received. 1 = Set when the bridge receives a target abort status from the backbone. Signaled Target Abort (STA) — R/WC. 11 10:9 0 = No signaled target abort 1 = Set when the bridge generates a completion packet with target abort status on the backbone. Reserved. Data Parity Error Detected (DPD) — R/WC. 8 7:5 Reserved. 4 Capabilities List (CLIST) — RO. Hardwired to 1. Capability list exist on the PCI bridge. 3 Interrupt Status (IS) — RO. Hardwired to 0. The PCI bridge does not generate interrupts. 2:0 11.1.5 0 = Data parity error Not detected. 1 = Set when the bridge receives a completion packet from the backbone from a previous request, and detects a parity error, and CMD.PERE is set (D30:F0:04 bit 6). Reserved RID—Revision Identification Register (PCI-PCI—D30:F0) Offset Address: 08h Default Value: See bit description 11.1.6 Attribute: Size: RO 8 bits Bit Description 7:0 Revision ID — RO. Refer to the Intel® I/O Controller Hub (ICH9) Family Specification Update for the value of the Revision ID Register CC—Class Code Register (PCI-PCI—D30:F0) Offset Address: 09h-0Bh Default Value: 060401h Bit 23:16 15:8 7:0 Attribute: Size: RO 24 bits Description Base Class Code (BCC) — RO. Hardwired to 06h. Indicates this is a bridge device. Sub Class Code (SCC) — RO. Hardwired to 04h. Indicates this device is a PCI-to-PCI bridge. Programming Interface (PI) — RO. Hardwired to 01h. Indicates the bridge is subtractive decode Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 399 PCI-to-PCI Bridge Registers (D30:F0) 11.1.7 PMLT—Primary Master Latency Timer Register (PCI-PCI—D30:F0) Offset Address: 0Dh Default Value: 00h Bit 11.1.8 7:3 Master Latency Timer Count (MLTC) — RO. Reserved per the PCI Express* Base Specification, Revision 1.0a. 2:0 Reserved HEADTYP—Header Type Register (PCI-PCI—D30:F0) Bit 7 6:0 Attribute: Size: RO 8 bits Description Multi-Function Device (MFD) — RO. ‘0’ indicates a single function device Header Type (HTYPE) — RO. This 7-bit field identifies the header layout of the configuration space, which is a PCI-to-PCI bridge in this case. BNUM—Bus Number Register (PCI-PCI—D30:F0) Offset Address: 18h-1Ah Default Value: 000000h Bit 23:16 15:8 7:0 400 RO 8 bits Description Offset Address: 0Eh Default Value: 01h 11.1.9 Attribute: Size: Attribute: Size: R/W 24 bits Description Subordinate Bus Number (SBBN) — R/W. Indicates the highest PCI bus number below the bridge. Secondary Bus Number (SCBN) — R/W. Indicates the bus number of PCI. Primary Bus Number (PBN) — R/W. This field is default to 00h. In a multiple-ICH system, programmable PBN allows an ICH to be located on any bus. System configuration software is responsible for initializing these registers to appropriate values. PBN is not used by hardware in determining its bus number. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.10 SMLT—Secondary Master Latency Timer Register (PCI-PCI—D30:F0) Offset Address: 1Bh Default Value: 00h Attribute: Size: R/W 8 bits This timer controls the amount of time the ICH9 PCI-to-PCI bridge will burst data on its secondary interface. The counter starts counting down from the assertion of FRAME#. If the grant is removed, then the expiration of this counter will result in the deassertion of FRAME#. If the grant has not been removed, then the ICH9 PCI-to-PCI bridge may continue ownership of the bus. 11.1.11 Bit Description 7:3 Master Latency Timer Count (MLTC) — R/W. This 5-bit field indicates the number of PCI clocks, in 8-clock increments, that the ICH9 remains as master of the bus. 2:0 Reserved IOBASE_LIMIT—I/O Base and Limit Register (PCI-PCI—D30:F0) Offset Address: 1Ch-1Dh Default Value: 0000h Attribute: Size: R/W, RO 16 bits Bit Description 15:12 I/O Limit Address Limit bits[15:12] — R/W. I/O Base bits corresponding to address lines 15:12 for 4-KB alignment. Bits 11:0 are assumed to be padded to FFFh. 11:8 I/O Limit Address Capability (IOLC) — RO. Indicates that the bridge does not support 32-bit I/O addressing. 7:4 I/O Base Address (IOBA) — R/W. I/O Base bits corresponding to address lines 15:12 for 4-KB alignment. Bits 11:0 are assumed to be padded to 000h. 3:0 I/O Base Address Capability (IOBC) — RO. Indicates that the bridge does not support 32-bit I/O addressing. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 401 PCI-to-PCI Bridge Registers (D30:F0) 11.1.12 SECSTS—Secondary Status Register (PCI-PCI—D30:F0) Offset Address: 1Eh–1Fh Default Value: 0280h Note: Attribute: Size: R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit Description Detected Parity Error (DPE) — R/WC. 15 0 = Parity error not detected. 1 = Intel® ICH9 PCI bridge detected an address or data parity error on the PCI bus 14 0 = SERR# assertion not received 1 = SERR# assertion is received on PCI. Received System Error (RSE) — R/WC. Received Master Abort (RMA) — R/WC. 13 0 = No master abort. 1 = This bit is set whenever the bridge is acting as an initiator on the PCI bus and the cycle is master-aborted. For (G)MCH/ICH9 interface packets that have completion required, this must also cause a target abort to be returned and sets PSTS.STA. (D30:F0:06 bit 11) Received Target Abort (RTA) — R/WC. 12 0 = No target abort. 1 = This bit is set whenever the bridge is acting as an initiator on PCI and a cycle is target-aborted on PCI. For (G)MCH/ICH9 interface packets that have completion required, this event must also cause a target abort to be returned, and sets PSTS.STA. (D30:F0:06 bit 11). Signaled Target Abort (STA) — R/WC. 11 10:9 0 = No target abort. 1 = This bit is set when the bridge is acting as a target on the PCI Bus and signals a target abort. DEVSEL# Timing (DEVT) — RO. 01h = Medium decode timing. Data Parity Error Detected (DPD) — R/WC. 8 • • • The bridge is the initiator on PCI. PERR# is detected asserted or a parity error is detected internally BCTRL.PERE (D30:F0:3E bit 0) is set. 7 Fast Back to Back Capable (FBC) — RO. Hardwired to 1 to indicate that the PCI to PCI target logic is capable of receiving fast back-to-back cycles. 6 Reserved 5 66 MHz Capable (66MHZ_CAP) — RO. Hardwired to 0. This bridge is 33 MHz capable only. 4:0 402 0 = Conditions described below not met. 1 = The ICH9 sets this bit when all of the following three conditions are met: Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.13 MEMBASE_LIMIT—Memory Base and Limit Register (PCI-PCI—D30:F0) Offset Address: 20h–23h Default Value: 00000000h Attribute: Size: R/W 32 bits This register defines the base and limit, aligned to a 1-MB boundary, of the nonprefetchable memory area of the bridge. Accesses that are within the ranges specified in this register will be sent to PCI if CMD.MSE is set. Accesses from PCI that are outside the ranges specified will be accepted by the bridge if CMD.BME is set. Bit 31:20 Memory Limit (ML) — R/W. These bits are compared with bits 31:20 of the incoming address to determine the upper 1-MB aligned value (exclusive) of the range. The incoming address must be less than this value. 19:16 Reserved 15:4 3:0 11.1.14 Description Memory Base (MB) — R/W. These bits are compared with bits 31:20 of the incoming address to determine the lower 1-MB aligned value (inclusive) of the range. The incoming address must be greater than or equal to this value. Reserved PREF_MEM_BASE_LIMIT—Prefetchable Memory Base and Limit Register (PCI-PCI—D30:F0) Offset Address: 24h–27h Default Value: 00010001h Attribute: Size: R/W, RO 32-bit Defines the base and limit, aligned to a 1-MB boundary, of the prefetchable memory area of the bridge. Accesses that are within the ranges specified in this register will be sent to PCI if CMD.MSE is set. Accesses from PCI that are outside the ranges specified will be accepted by the bridge if CMD.BME is set. Bit Description 31:20 Prefetchable Memory Limit (PML) — R/W. These bits are compared with bits 31:20 of the incoming address to determine the upper 1-MB aligned value (exclusive) of the range. The incoming address must be less than this value. 19:16 15:4 3:0 64-bit Indicator (I64L) — RO. Indicates support for 64-bit addressing. Prefetchable Memory Base (PMB) — R/W. These bits are compared with bits 31:20 of the incoming address to determine the lower 1-MB aligned value (inclusive) of the range. The incoming address must be greater than or equal to this value. 64-bit Indicator (I64B) — RO. Indicates support for 64-bit addressing. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 403 PCI-to-PCI Bridge Registers (D30:F0) 11.1.15 PMBU32—Prefetchable Memory Base Upper 32 Bits Register (PCI-PCI—D30:F0) Offset Address: 28h–2Bh Default Value: 00000000h Bit 31:0 11.1.16 Prefetchable Memory Base Upper Portion (PMBU) — R/W. Upper 32-bits of the prefetchable address base. PMLU32—Prefetchable Memory Limit Upper 32 Bits Register (PCI-PCI—D30:F0) Bit 31:0 R/W 32 bits Prefetchable Memory Limit Upper Portion (PMLU) — R/W. Upper 32-bits of the prefetchable address limit. CAPP—Capability List Pointer Register (PCI-PCI—D30:F0) Attribute: Size: RO 8 bits Bit Description 7:0 Capabilities Pointer (PTR) — RO. Indicates that the pointer for the first entry in the capabilities list is at 50h in configuration space. INTR—Interrupt Information Register (PCI-PCI—D30:F0) Offset Address: 3Ch–3Dh Default Value: 0000h Bit 15:8 7:0 404 Attribute: Size: Description Offset Address: 34h Default Value: 50h 11.1.18 R/W 32 bits Description Offset Address: 2C–2Fh Default Value: 00000000h 11.1.17 Attribute: Size: Attribute: Size: R/W, RO 16 bits Description Interrupt Pin (IPIN) — RO. The PCI bridge does not assert an interrupt. Interrupt Line (ILINE) — R/W. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. Since the bridge does not generate an interrupt, BIOS should program this value to FFh as per the PCI bridge specification. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.19 BCTRL—Bridge Control Register (PCI-PCI—D30:F0) Offset Address: 3Eh–3Fh Default Value: 0000h Bit 15:12 11 10 9 Attribute: Size: R/WC, RO, R/W 16 bits Description Reserved Discard Timer SERR# Enable (DTE) — R/W. Controls the generation of SERR# on the primary interface in response to the DTS bit being set: 0 = Do not generate SERR# on a secondary timer discard 1 = Generate SERR# in response to a secondary timer discard Discard Timer Status (DTS) — R/WC. This bit is set to 1 when the secondary discard timer (see the SDT bit below) expires for a delayed transaction in the hard state. Secondary Discard Timer (SDT) — R/W. This bit sets the maximum number of PCI clock cycles that the Intel® ICH9 waits for an initiator on PCI to repeat a delayed transaction request. The counter starts once the delayed transaction data is has been returned by the system and is in a buffer in the ICH9 PCI bridge. If the master has not repeated the transaction at least once before the counter expires, the ICH9 PCI bridge discards the transaction from its queue. 0 = The PCI master timeout value is between 215 and 216 PCI clocks 1 = The PCI master timeout value is between 210 and 211 PCI clocks 8 Primary Discard Timer (PDT) — R/W. This bit is R/W for software compatibility only. 7 Fast Back to Back Enable (FBE) — RO. Hardwired to 0. The PCI logic will not generate fast back-to-back cycles on the PCI bus. Secondary Bus Reset (SBR) — R/W. Controls PCIRST# assertion on PCI. 6 0 = Bridge de-asserts PCIRST# 1 = Bridge asserts PCIRST#. When PCIRST# is asserted, the delayed transaction buffers, posting buffers, and the PCI bus are initialized back to reset conditions. The rest of the part and the configuration registers are not affected. Master Abort Mode (MAM) — R/W. Controls the ICH9 PCI bridge’s behavior when a master abort occurs: Master Abort on (G)MCH/ICH9 Interconnect (DMI): 0 = Bridge asserts TRDY# on PCI. It drives all 1s for reads, and discards data on writes. 1 = Bridge returns a target abort on PCI. 5 Master Abort PCI (non-locked cycles): 0 = Normal completion status will be returned on the (G)MCH/ICH9 interconnect. 1 = Target abort completion status will be returned on the (G)MCH/ICH9 interconnect. NOTE: All locked reads will return a completer abort completion status on the (G)MCH/ ICH9 interconnect. 4 VGA 16-Bit Decode (V16D) — R/W. Enables the ICH9 PCI bridge to provide 16-bits decoding of VGA I/O address precluding the decode of VGA alias addresses every 1 KB. This bit requires the VGAE bit in this register be set. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 405 PCI-to-PCI Bridge Registers (D30:F0) Bit Description VGA Enable (VGAE) — R/W. When set to a 1, the ICH9 PCI bridge forwards the following transactions to PCI regardless of the value of the I/O base and limit registers. The transactions are qualified by CMD.MSE (D30:F0:04 bit 1) and CMD.IOSE (D30:F0:04 bit 0) being set. 3 • • Memory addresses: 000A0000h-000BFFFFh I/O addresses: 3B0h-3BBh and 3C0h-3DFh. For the I/O addresses, bits [63:16] of the address must be 0, and bits [15:10] of the address are ignored (i.e., aliased). The same holds true from secondary accesses to the primary interface in reverse. That is, when the bit is 0, memory and I/O addresses on the secondary interface between the above ranges will be claimed. 2 ISA Enable (IE) — R/W. This bit only applies to I/O addresses that are enabled by the I/O Base and I/O Limit registers and are in the first 64 KB of PCI I/O space. If this bit is set, the ICH9 PCI bridge will block any forwarding from primary to secondary of I/O transactions addressing the last 768 bytes in each 1-KB block (offsets 100h to 3FFh). SERR# Enable (SEE) — R/W. Controls the forwarding of secondary interface SERR# assertions on the primary interface. When set, the PCI bridge will forward SERR# pin. 1 • • • SERR# is asserted on the secondary interface. This bit is set. CMD.SEE (D30:F0:04 bit 8) is set. Parity Error Response Enable (PERE) — R/W. 0 11.1.20 0 = Disable 1 = The ICH9 PCI bridge is enabled for parity error reporting based on parity errors on the PCI bus. SPDH—Secondary PCI Device Hiding Register (PCI-PCI—D30:F0) Offset Address: 40h–41h Default Value: 0000h Attribute: Size: R/W, RO 16 bits This register allows software to hide the PCI devices, either plugged into slots or on the motherboard. Bit 15:4 Description Reserved 3 Hide Device 3 (HD3) — R/W, RO. Same as bit 0 of this register, except for device 3 (AD[19]) 2 Hide Device 2 (HD2) — R/W, RO. Same as bit 0 of this register, except for device 2 (AD[18]) 1 Hide Device 1 (HD1) — R/W, RO. Same as bit 0 of this register, except for device 1 (AD[17]) Hide Device 0 (HD0) — R/W, RO. 0 406 0 = The PCI configuration cycles for this slot are not affected. 1 = Intel® ICH9 hides device 0 on the PCI bus. This is done by masking the IDSEL (keeping it low) for configuration cycles to that device. Since the device will not see its IDSEL go active, it will not respond to PCI configuration cycles and the processor will think the device is not present. AD[16] is used as IDSEL for device 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.21 DTC—Delayed Transaction Control Register (PCI-PCI—D30:F0) Offset Address: 44h–47h Default Value: 00000000h Bit Attribute: Size: R/W 32 bits Description Discard Delayed Transactions (DDT) — R/W. 31 0 = Logged delayed transactions are kept. 1 = The ICH9 PCI bridge will discard any delayed transactions it has logged. This includes transactions in the pending queue, and any transactions in the active queue, whether in the hard or soft DT state. The prefetchers will be disabled and return to an idle state. NOTES:If a transaction is running on PCI at the time this bit is set, that transaction will continue until either the PCI master disconnects (by de-asserting FRAME#) or the PCI bridge disconnects (by asserting STOP#). This bit is cleared by the PCI bridge when the delayed transaction queues are empty and have returned to an idle state. Software sets this bit and polls for its completion Block Delayed Transactions (BDT) — R/W. 30 29:8 0 = Delayed transactions accepted 1 = The ICH9 PCI bridge will not accept incoming transactions which will result in delayed transactions. It will blindly retry these cycles by asserting STOP#. All postable cycles (memory writes) will still be accepted. Reserved Maximum Delayed Transactions (MDT) — R/W. Controls the maximum number of delayed transactions that the ICH9 PCI bridge will run. Encodings are: 7:6 00 =) 2 Active, 5 pending 01 =) 2 active, no pending 10 =) 1 active, no pending 11 =) Reserved 5 Reserved Auto Flush After Disconnect Enable (AFADE) — R/W. 4 0 = The PCI bridge will retain any fetched data until required to discard by producer/ consumer rules. 1 = The PCI bridge will flush any prefetched data after either the PCI master (by deasserting FRAME#) or the PCI bridge (by asserting STOP#) disconnects the PCI transfer. Never Prefetch (NP) — R/W. 3 0 = Prefetch enabled 1 = The ICH9 will only fetch a single DW and will not enable prefetching, regardless of the command being an Memory read (MR), Memory read line (MRL), or Memory read multiple (MRM). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 407 PCI-to-PCI Bridge Registers (D30:F0) Bit Description Memory Read Multiple Prefetch Disable (MRMPD) — R/W. 2 0 = MRM commands will fetch multiple cache lines as defined by the prefetch algorithm. 1 = Memory read multiple (MRM) commands will fetch only up to a single, 64-byte aligned cache line. Memory Read Line Prefetch Disable (MRLPD) — R/W. 1 0 = MRL commands will fetch multiple cache lines as defined by the prefetch algorithm. 1 = Memory read line (MRL) commands will fetch only up to a single, 64-byte aligned cache line. Memory Read Prefetch Disable (MRPD) — R/W. 0 11.1.22 0 = MR commands will fetch up to a 64-byte aligned cache line. 1 = Memory read (MR) commands will fetch only a single DW. BPS—Bridge Proprietary Status Register (PCI-PCI—D30:F0) Offset Address: 48h–4Bh Default Value: 00000000h Bit 31:17 16 Attribute: Size: R/WC, RO 32 bits Description Reserved PERR# Assertion Detected (PAD) — R/WC. This bit is set by hardware whenever the PERR# pin is asserted on the rising edge of PCI clock. This includes cases in which the chipset is the agent driving PERR#. It remains asserted until cleared by software writing a 1 to this location. When enabled by the PERR#-to-SERR# Enable bit (in the Bridge Policy Configuration register), a 1 in this bit can generate an internal SERR# and be a source for the NMI logic. This bit can be used by software to determine the source of a system problem. 15:7 Reserved Number of Pending Transactions (NPT) — RO. This read-only indicator tells debug software how many transactions are in the pending queue. Possible values are: 000 = No pending transaction 001 = 1 pending transaction 010 = 2 pending transactions 6:4 011 = 3 pending transactions 100 = 4 pending transactions 101 = 5 pending transactions 110 - 111 = Reserved NOTE: This field is not valid if DTC.MDT (offset 44h:bits 7:6) is any value other than ‘00’. 3:2 Reserved Number of Active Transactions (NAT) — RO. This read-only indicator tells debug software how many transactions are in the active queue. Possible values are: 1:0 00 = No active transactions 01 = 1 active transaction 10 = 2 active transactions 11 = Reserved 408 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet PCI-to-PCI Bridge Registers (D30:F0) 11.1.23 BPC—Bridge Policy Configuration Register (PCI-PCI—D30:F0) Offset Address: 4Ch–4Fh Default Value: 00001200h Attribute: Size: Bit 31:14 13:8 R/W 32 bits Description Reserved Upstream Read Latency Threshold (URLT) — R/W: This field specifies the number of PCI clocks after internally enqueuing an upstream memory read request at which point the PCI target logic should insert wait states in order to optimize lead-off latency. When the master returns after this threshold has been reached and data has not arrived in the Delayed Transaction completion queue, then the PCI target logic will insert wait states instead of immediately retrying the cycle. The PCI target logic will insert up to 16 clocks of target initial latency (from FRAME# assertion to TRDY# or STOP# assertion) before retrying the PCI read cycle (if the read data has not arrived yet). Note that the starting event for this Read Latency Timer is not explicitly visible externally. A value of 0h disables this policy completely such that wait states will never be inserted on the read lead-off data phase. The default value (12h) specifies 18 PCI clocks (540 ns) and is approximately 4 clocks less than the typical idle lead-off latency expected for desktop ICH9 systems. This value may need to be changed by BIOS, depending on the platform. Subtractive Decode Policy (SDP) — R/W. 0 = The PCI bridge always forwards memory and I/O cycles that are not claimed by any other device on the backbone (primary interface) to the PCI bus (secondary interface). 1 = The PCI bridge will not claim and forward memory or I/O cycles at all unless the corresponding Space Enable bit is set in the Command register. NOTE: The Boot BIOS Destination Selection strap can force the BIOS accesses to PCI. 7 6 CMD.MSE BPC.SDP Range Forwarding Policy 0 0 Don’t Care Forward unclaimed cycles 0 1 Don’t Care Forwarding Prohibited 1 X Within range Positive decode and forward 1 X Outside Subtractive decode & forward PERR#-to-SERR# Enable (PSE) — R/W. When this bit is set, a 1 in the PERR# Assertion status bit (in the Bridge Proprietary Status register) will result in an internal SERR# assertion on the primary side of the bridge (if also enabled by the SERR# Enable bit in the primary Command register). SERR# is a source of NMI. Secondary Discard Timer Testmode (SDTT) — R/W. 5 4:3 0 = The secondary discard timer expiration will be defined in BCTRL.SDT (D30:F0:3E, bit 9) 1 = The secondary discard timer will expire after 128 PCI clocks. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 409 PCI-to-PCI Bridge Registers (D30:F0) Bit Description Peer Decode Enable (PDE) — R/W. 2 11.1.24 0 = The PCI bridge assumes that all memory cycles target main memory, and all I/O cycles are not claimed. 1 = The PCI bridge will perform peer decode on any memory or I/O cycle from PCI that falls outside of the memory and I/O window registers 1 Reserved 0 Received Target Abort SERR# Enable (RTAE) — R/W. When set, the PCI bridge will report SERR# when PSTS.RTA (D30:F0:06 bit 12) or SSTS.RTA (D30:F0:1E bit 12) are set, and CMD.SEE (D30:F0:04 bit 8) is set. SVCAP—Subsystem Vendor Capability Register (PCI-PCI—D30:F0) Offset Address: 50h–51h Default Value: 000Dh Bit 15:8 7:0 11.1.25 Attribute: Size: RO 16 bits Description Next Capability (NEXT) — RO. Value of 00h indicates this is the last item in the list. Capability Identifier (CID) — RO. Value of 0Dh indicates this is a PCI bridge subsystem vendor capability. SVID—Subsystem Vendor IDs Register (PCI-PCI—D30:F0) Offset Address: 54h–57h Default Value: 00000000h Bit Attribute: Size: R/WO 32 bits Description 31:16 Subsystem Identifier (SID) — R/WO. Indicates the subsystem as identified by the vendor. This field is write once and is locked down until a bridge reset occurs (not the PCI bus reset). 15:0 Subsystem Vendor Identifier (SVID) — R/WO. Indicates the manufacturer of the subsystem. This field is write once and is locked down until a bridge reset occurs (not the PCI bus reset). §§ 410 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12 Gigabit LAN Configuration Registers 12.1 Gigabit LAN Configuration Registers (Gigabit LAN — D25:F0) Note: Register address locations that are not shown in Table 12-1 should be treated as Reserved. / Table 12-1. Gigabit LAN Configuration Registers Address Map (Gigabit LAN —D25:F0) (Sheet 1 of 2) Offset Mnemonic Register Name Default Type 00h–01h VID Vendor Identification 8086h RO 02h–03h DID Device Identification See register description RO 04h–05h PCICMD PCI Command 0000h R/W, RO 06h–07h PCISTS PCI Status 0010h R/WC, RO 08h RID Revision Identification See register description RO 09h–0Bh CC Class Code 020000h RO 0Ch CLS Cache Line Size 00h R/W 0Dh PLT Primary Latency Timer 00h RO 0Eh HEADTYP Header Type 00h RO 10h–13h MBARA 00000000h R/W, RO Memory Base Address A 14h–17h MBARB Memory Base Address B 00000000h R/W, RO 18h–1Bh MBARC Memory Base Address C 00000001h R/W, RO 2Ch–2Dh SID Subsystem ID See register description RO 2Eh–2Fh SVID Subsystem Vendor ID See register description RO 30h–33h ERBA Expansion ROM Base Address See register description RO 34h CAPP Capabilities List Pointer C8h RO 3Ch–3Dh INTR Interrupt Information See register description R/W, RO 3Eh MLMG Maximum Latency/Minimum Grant 00h RO C8h–C9h CLIST1 D001h RO, R/WO CAh–CBh PMC PCI Power Management Capability See register description RO CCh–CDh PMCS PCI Power Management Control and Status See register description R/WC, R/W, RO Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Capabilities List 1 411 Gigabit LAN Configuration Registers Table 12-1. Gigabit LAN Configuration Registers Address Map (Gigabit LAN —D25:F0) (Sheet 2 of 2) 12.1.1 Offset Mnemonic CFh DR D0h–D1h CLIST2 D2h–D3h MCTL D4h–D7h MADDL D8h–DBh MADDH DCh–DDh MDAT E0h–E1h FLRCAP E2h–E3h FLRCLV E4h–E5h DEVCTRL Register Name Default Type See register description RO Capabilities List 2 E005h R/WO, RO Message Control 0080h R/W, RO Message Address Low See register description R/W Message Address High See register description R/W Message Data See register description R/W Function Level Reset Capability 0009h RO Function Level Reset Capability Length and Value See register description R/WO, RO 0000h R/W, RO Data Register Device Control VID—Vendor Identification Register (Gigabit LAN—D25:F0) Address Offset: 00h–01h Default Value: 8086h 12.1.2 RO 16 bits Bit Description 15:0 Vendor ID — RO. This is a 16-bit value assigned to Intel. The field may be auto-loaded from the NVM at address 0Eh during init time depending on the "Load Vendor/Device ID" bit field in NVM word 0Ah with a default value of 8086h. DID—Device Identification Register (Gigabit LAN—D25:F0) Address Offset: 02h–03h Default Value: See bit description Bit 15:0 412 Attribute: Size: Attribute: Size: RO 16 bits Description Device ID — RO. This is a 16-bit value assigned to the Intel® ICH9 Gigabit LAN controller. The field may be auto-loaded from the NVM word 0Dh during initialization time depending on the "Load Vendor/Device ID" bit field in NVM word 0Ah. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.3 PCICMD—PCI Command Register (Gigabit LAN—D25:F0) Address Offset: 04h–05h Default Value: 0000h Bit 15:11 Attribute: Size: R/W, RO 16 bits Description Reserved Interrupt Disable — R/W. This disables pin-based INTx# interrupts on enabled HotPlug and power management events. This bit has no effect on MSI operation. 10 0 = Internal INTx# messages are generated if there is an interrupt for Hot-Plug or power management and MSI is not enabled. 1 = Internal INTx# messages will not be generated. This bit does not affect interrupt forwarding from devices connected to the root port. Assert_INTx and Deassert_INTx messages will still be forwarded to the internal interrupt controllers if this bit is set. 9 Fast Back to Back Enable (FBE) — RO. Hardwired to ‘0’. SERR# Enable (SEE) — R/W. 8 7 0 = Disable 1 = Enables the Gb LAN controller to generate an SERR# message when PSTS.SSE is set. Wait Cycle Control (WCC) — RO. Hardwired to ‘0’. Parity Error Response (PER) — R/W. 6 0 = Disable. 1 = Indicates that the device is capable of reporting parity errors as a master on the backbone. 5 Palette Snoop Enable (PSE) — RO. Hardwired to ‘0’. 4 Postable Memory Write Enable (PMWE) — RO. Hardwired to ‘0’. 3 Special Cycle Enable (SCE) — RO. Hardwired to ‘0’. Bus Master Enable (BME) — R/W. 2 0 = Disable. All cycles from the device are master aborted 1 = Enable. Allows the root port to forward cycles onto the backbone from a Gigabit LAN* device. Memory Space Enable (MSE) — R/W. 1 0 = Disable. Memory cycles within the range specified by the memory base and limit registers are master aborted on the backbone. 1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers can be forwarded to the Gigabit LAN device. I/O Space Enable (IOSE) — R/W. This bit controls access to the I/O space registers. 0 0 = Disable. I/O cycles within the range specified by the I/O base and limit registers are master aborted on the backbone. 1 = Enable. Allows I/O cycles within the range specified by the I/O base and limit registers can be forwarded to the Gigabit LAN device. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 413 Gigabit LAN Configuration Registers 12.1.4 PCISTS—PCI Status Register (Gigabit LAN—D25:F0) Address Offset: 06h–07h Default Value: 0010h Bit Attribute: Size: R/WC, RO 16 bits Description Detected Parity Error (DPE) — R/WC. 15 0 = No parity error detected. 1 = Set when the Gb LAN controller receives a command or data from the backbone with a parity error. This is set even if PCIMD.PER (D25:F0, bit 6) is not set. Signaled System Error (SSE) — R/WC. 14 0 = No system error signaled. 1 = Set when the Gb LAN controller signals a system error to the internal SERR# logic. Received Master Abort (RMA) — R/WC. 13 0 = Root port has not received a completion with unsupported request status from the backbone. 1 = Set when the Gb LAN controller receives a completion with unsupported request status from the backbone. Received Target Abort (RTA) — R/WC. 12 0 = Root port has not received a completion with completer abort from the backbone. 1 = Set when the Gb LAN controller receives a completion with completer abort from the backbone. Signaled Target Abort (STA) — R/WC. 11 10:9 0 = No target abort received. 1 = Set whenever the Gb LAN controller forwards a target abort received from the downstream device onto the backbone. DEVSEL# Timing Status (DEV_STS) — RO. Hardwired to ‘0’. Master Data Parity Error Detected (DPED) — R/WC. 8 0 = No data parity error received. 1 = Set when the Gb LAN Controller receives a completion with a data parity error on the backbone and PCIMD.PER (D25:F0, bit 6) is set. 7 Fast Back to Back Capable (FB2BC) — RO. Hardwired to ‘0’. 6 Reserved 5 66 MHz Capable — RO. Hardwired to ‘0’. 4 Capabilities List — RO. Hardwired to ‘1’. Indicates the presence of a capabilities list. Interrupt Status — RO. Indicates status of Hot-Plug and power management interrupts on the root port that result in INTx# message generation. 3 0 = Interrupt is deasserted. 1 = Interrupt is asserted. This bit is not set if MSI is enabled. If MSI is not enabled, this bit is set regardless of the state of PCICMD.Interrupt Disable bit (D25:F0:04h:bit 10). 2:0 414 Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.5 RID—Revision Identification Register (Gigabit LAN—D25:F0) Offset Address: 08h Default Value: See bit description 12.1.6 Attribute: Size: Bit Description 7:0 Revision ID — RO. Refer to the Intel® I/O Controller Hub (ICH9) Family Specification Update for the value of the Revision ID Register CC—Class Code Register (Gigabit LAN—D25:F0) Address Offset: 09h–0Bh Default Value: 020000h Bit 23:0 12.1.7 RO 24 bits Class Code— RO. Identifies the device as an Ethernet Adapter. 020000h = Ethernet Adapter. CLS—Cache Line Size Register (Gigabit LAN—D25:F0) Attribute: Size: R/W 8 bits Bit Description 7:0 Cache Line Size — R/W. This field is implemented by PCI devices as a read write field for legacy compatibility purposes but has no impact on any device functionality. PLT—Primary Latency Timer Register (Gigabit LAN—D25:F0) Address Offset: 0Dh Default Value: 00h Bit 7:0 12.1.9 Attribute: Size: Description Address Offset: 0Ch Default Value: 00h 12.1.8 RO 8 bits Attribute: Size: RO 8 bits Description Latency Timer (LT) — RO. Hardwired to ‘0’. HT—Header Type Register (Gigabit LAN—D25:F0) Address Offset: 0Eh Default Value: 00h Bit 7:0 Attribute: Size: RO 8 bits Description Header Type (HT) — RO. 00h = Indicates this is a single function device. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 415 Gigabit LAN Configuration Registers 12.1.10 MBARA—Memory Base Address Register A (Gigabit LAN—D25:F0) Address Offset: 10h–13h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits The internal CSR registers and memories are accessed as direct memory mapped offsets from the base address register. SW may only access whole DWord at a time. Bit 31:17 16:4 3 2:1 0 12.1.11 Description Base Address (BA) — R/W. Software programs this field with the base address of this region. Memory Size (MSIZE) — R/W. Memory size is 128K Bytes. Prefetchable Memory (PM) — RO. The GbE LAN controller does not implement prefetchable memory. Memory Type (MT) — RO. Set to 00b indicating a 32 bit BAR. Memory / IO Space (MIOS) — RO. Set to ‘0’ indicating a Memory Space BAR. MBARB—Memory Base Address Register B (Gigabit LAN—D25:F0) Address Offset: 14h–17h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits The internal registers that are used to access the LAN Space in the External FLASH device. Access to these registers are direct memory mapped offsets from the base address register. SW may only access a DWord at a time. Bit 31:12 11:4 3 2:1 0 416 Description Base Address (BA) — R/W. Software programs this field with the base address of this region. Memory Size (MSIZE) — R/W. Memory size is 4K Bytes. Prefetchable Memory (PM) — RO. The Gb LAN controller does not implement prefetchable memory. Memory Type (MT) — RO. Set to 00b indicating a 32 bit BAR. Memory / IO Space (MIOS) — RO. Set to ‘0’ indicating a Memory Space BAR. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.12 MBARC—Memory Base Address Register C (Gigabit LAN—D25:F0) Address Offset: 18h–1Bh Default Value: 00000001h Attribute: Size: R/W, RO 32 bits Internal registers, and memories, can be accessed using I/O operations. There are two 4B registers in the IO mapping window: Addr Reg and Data Reg. SW may only access a Dword at a time. Bit 31:5 4:1 0 12.1.13 Description Base Address (BA) — R/W. Software programs this field with the base address of this region. I/O Size (IOSIZE) — RO. I/O space size is 32 Bytes. Memory / IO Space (MIOS) — RO. Set to ‘1’ indicating an IO Space BAR. SVID—Subsystem Vendor ID Register (Gigabit LAN—D25:F0) Address Offset: 2Ch–2Dh Default Value: See bit description 12.1.14 RO 16 bits Bit Description 15:0 Subsystem Vendor ID (SVID) — RO. This value may be loaded automatically from the NVM Word 0Ch upon power up depending on the "Load Subsystem ID" bit field in NVM word 0Ah. A value of 8086h is default for this field upon power up if the NVM does not respond or is not programmed. All functions are initialized to the same value. SID—Subsystem ID Register (Gigabit LAN—D25:F0) Address Offset: 2Eh–2Fh Default Value: See bit description Bit 15:0 12.1.15 Attribute: Size: Attribute: Size: RO 16 bits Description Subsystem ID (SID) — RO. This value may be loaded automatically from the NVM Word 0Bh upon power up or reset depending on the “Load Subsystem ID” bit field in NVM word 0Ah with a default value of 0000h. This value is loadable from NVM word location 0Bh. ERBA—Expansion ROM Base Address Register (Gigabit LAN—D25:F0) Address Offset: 30h–33h Default Value: See bit description Attribute: Size: RO 32 bits Bit Description 32:0 Expansion ROM Base Address (ERBA) — RO. This register is used to define the address and size information for boot-time access to the optional FLASH memory. If no Flash memory exists this register reports 00000000h. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 417 Gigabit LAN Configuration Registers 12.1.16 CAPP—Capabilities List Pointer Register (Gigabit LAN—D25:F0) Address Offset: 34h Default Value: C8h 12.1.17 Attribute: Size: R0 8 bits Bit Description 7:0 Capabilities Pointer (PTR) — RO. Indicates that the pointer for the first entry in the capabilities list is at C8h in configuration space. INTR—Interrupt Information Register (Gigabit LAN—D25:F0) Address Offset: 3Ch–3Dh Default Value: 0100h Function Level Reset: No Bit 15:8 Attribute: Size: R/W, RO 16 bits Description Interrupt Pin (IPIN) — RO. Indicates the interrupt pin driven by the Gb LAN controller. 01h = The Gb LAN controller implements legacy interrupts on INTA. 7:0 12.1.18 Interrupt Line (ILINE) — R/W. Default = 00h. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. MLMG—Maximum Latency/Minimum Grant Register (Gigabit LAN—D25:F0) Address Offset: 3Eh Default Value: 00h Bit 7:0 12.1.19 RO 8 bits Description Maximum Latency/Minimum Grant (MLMG) — RO. Not used. Hardwired to 00h. CLIST 1—Capabilities List Register 1 (Gigabit LAN—D25:F0) Address Offset: C8h–C9h Default Value: D001h Attribute: Size: RO, R/WO 16 bits Bit Description 15:8 Next Capability (NEXT) — RO. Value of D0h indicates the location of the next pointer. 7:0 418 Attribute: Size: Capability ID (CID) — RO. Indicates the linked list item is a PCI Power Management Register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.20 PMC—PCI Power Management Capabilities Register (Gigabit LAN—D25:F0) Address Offset: CAh–CBh Default Value: See bit descriptions Function Level Reset: No (Bits 15:11 only) Bit Attribute: Size: RO 16 bits Description PME_Support (PMES) — RO. This five-bit field indicates the power states in which the function may assert PME#. It depend on PM Ena and AUX-PWR bits in word 0Ah in the NVM: 15:11 Condition Function Value PM Ena=0 No PME at all states 0000b PM Ena & AUX-PWR=0 PME at D0 and D3hot 01001b PM Ena & AUX-PWR=1 PME at D0, D3hot and D3cold 11001b These bits are not reset by Function Level Reset. 10 D2_Support (D2S) — RO. The D2 state is not supported. 9 D1_Support (D1S) — RO. The D1 state is not supported. 8:6 Aux_Current (AC) — RO. Required current defined in the Data Register. 5 Device Specific Initialization (DSI) — RO. Set to ‘1’. The GbE LAN Controller requires its device driver to be executed following transition to the D0 un-initialized state. 4 Reserved 3 PME Clock (PMEC) — RO. Hardwired to ‘0’. 2:0 Version (VS) — RO. Hardwired to 010b to indicate support for Revision 1.1 of the PCI Power Management Specification. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 419 Gigabit LAN Configuration Registers 12.1.21 PMCS—PCI Power Management Control and Status Register (Gigabit LAN—D25:F0) Address Offset: CCh–CDh Default Value: See bit description Function Level Reset: No (Bit 8 only) Bit 15 Attribute: Size: R/WC, R/W, RO 16 bits Description PME Status (PMES) — R/WC. This bit is set to ‘1’ when the function detects a wakeup event independent of the state of the PMEE bit. Writing a “1” will clear this bit. Data Scale (DSC) — R/W. This field indicates the scaling factor to be used when interpreting the value of the Data register. 14:13 For the GbE LAN and common functions this field equals 01b (indicating 0.1 watt units) if the PM is enabled in the NVM, and the Data_Select field is set to 0, 3, 4, 7, (or 8 for Function 0). Else it equals 00b. For the manageability functions this field equals 10b (indicating 0.01 watt units) if the PM is enabled in the NVM, and the Data_Select field is set to 0, 3, 4, 7. Else it equals 00b. Data Select (DSL) — R/W. This four-bit field is used to select which data is to be reported through the Data register (offset CFh) and Data_Scale field. These bits are writeable only when the Power Management is enabled via NVM. 0h = D0 Power Consumption 12:9 3h = D3 Power Consumption 4h = D0 Power Dissipation 7h = D3 Power Dissipation 8h = Common Power All other values are reserved. 8 7:2 PME Enable (PMEE) — R/W. If Power Management is enabled in the NVM, writing a ‘1’ to this register will enable Wakeup. If Power Management is disabled in the NVM, writing a “1” to this bit has no affect, and will not set the bit to “1”. This bit is not reset by Function Level Reset. Reserved - Returns a value of ‘000000’. Power State (PS) — R/W. This field is used both to determine the current power state of the GbE LAN Controller and to set a new power state. The values are: 00 – D0 state (default) 1:0 01 – Ignored 10 – Ignored 11 – D3 state (Power Management must be enables in the NVM or this cycle will be ignored). 420 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.22 DR—Data Register (Gigabit LAN—D25:F0) Address Offset: CFh Default Value: See bit description 12.1.23 Attribute: Size: RO 8 bits Bit Description 7:0 Reported Data (RD) — RO. This register is used to report power consumption and heat dissipation. This register is controlled by the Data_Select field in the PMCS (Offset CCh, bits 12:9), and the power scale is reported in the Data_Scale field in the PMCS (Offset CCh, bits 14:13). The data of this field is loaded from the NVM if PM is enabled in the NVM or with a default value of 0x00 otherwise. CLIST 2—Capabilities List Register 2 (Gigabit LAN—D25:F0) Address Offset: D0h–D1h Default Value: E005h Function Level Reset: No (Bits 15:8 only) Bit 15:8 Attribute: Size: R/WO, RO 16 bits Description Next Capability (NEXT) — R/WO. Value of E0h points to the Function Level Reset capability structure. These bits are not reset by Function Level Reset. 7:0 12.1.24 Capability ID (CID) — RO. Indicates the linked list item is a Message Signaled Interrupt Register. MCTL—Message Control Register (Gigabit LAN—D25:F0) Address Offset: D2h–D3h Default Value: 0080h Bit 15:8 7 Attribute: Size: R/W, RO 16 bits Description Reserved 64-bit Capable (CID) — RO. Set to ‘1’ to indicate that the GbE LAN Controller is capable of generating 64-bit message addresses. 6:4 Multiple Message Enable (MME) — RO. Returns 000b to indicate that the GbE LAN controller only supports a single message. 3:1 Multiple Message Capable (MMC) — RO. The GbE LAN controller does not support multiple messages. MSI Enable (MSIE) — R/W. 0 0 = MSI generation is disabled. 1 = The Gb LAN controller will generate MSI for interrupt assertion instead of INTx signaling. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 421 Gigabit LAN Configuration Registers 12.1.25 MADDL—Message Address Low Register (Gigabit LAN—D25:F0) Address Offset: D4h–D7h Default Value: See bit description 12.1.26 Attribute: Size: Bit Description 31:0 Message Address Low (MADDL) — R/W. Written by the system to indicate the lower 32 bits of the address to use for the MSI memory write transaction. The lower two bits will always return 0 regardless of the write operation. MADDH—Message Address High Register (Gigabit LAN—D25:F0) Address Offset: D8h–DBh Default Value: See bit description Bit 31:0 12.1.27 Attribute: Size: R/W 32 bits Description Message Address High (MADDH) — R/W. Written by the system to indicate the upper 32 bits of the address to use for the MSI memory write transaction. MDAT—Message Data Register (Gigabit LAN—D25:F0) Address Offset: DCh–DDh Default Value: See bit description 12.1.28 R/W 32 bits Attribute: Size: R/W 16 bits Bit Description 31:0 Message Data (MDAT) — R/W. Written by the system to indicate the lower 16 bits of the data written in the MSI memory write DWORD transaction. The upper 16 bits of the transaction are written as 0000h. FLRCAP—Function Level Reset Capability (Gigabit LAN—D25:F0) Address Offset: E0h–E1h Default Value: 0009h Bit 15:8 Attribute: Size: RO 16 bits Description Next Pointer — RO. This field provides an offset to the next capability item in the capability list. The value of 00h indicates the last item in the list. Capability ID — RO. The value of this field depends on the FLRCSSEL bit. 7:0 13h = If FLRCSSEL = 0 09h = If FLRCSSEL = 1, indicating vendor specific capability. 422 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.1.29 FLRCLV—Function Level Reset Capability Length and Version (Gigabit LAN—D25:F0) Address Offset: E2h–E3h Attribute: R/WO, RO Default Value: See Description. Size: 16 bits Function Level Reset: No (Bits 9:8 Only When FLRCSSEL = 0) When FLRCSSEL = 0, this register is defined as follows: Bit 15:10 9 Description Reserved. Function Level Reset Capability — R/WO. 1 = Support for Function Level Reset. This bit is not reset by Function Level Reset. 8 TXP Capability — R/WO. 1 = Indicates support for the Transactions Pending (TXP) bit. TXP must be supported if FLR is supported. 7:0 Capability Length — RO. The value of this field indicates the number of bytes of the vendor specific capability as require by the PCI spec. It has the value of 06h for the Function Level Reset capability. When FLRCSSEL = 1, this register is defined as follows: Bit 15:12 12.1.30 Description Vendor Specific Capability ID — RO. A value of 2h in this field identifies this capability as Function Level Reset. 11:8 Capability Version— RO. The value of this field indicates the version of the Function Level Reset Capability. Default is 0h. 7:0 Capability Length — RO. The value of this field indicates the number of bytes of the vendor specific capability as require by the PCI spec. It has the value of 06h for the Function Level Reset capability. DEVCTRL—Device Control (Gigabit LAN—D25:F0) Address Offset: E4-E5h Default Value: 0000h Bit 15:9 8 Attribute: Size: R/W, RO 16 bits Description Reserved. Transactions Pending (TXP) — R/W. 1 = Indicates the controller has issued Non-Posted requests which have not been completed. 0 = Indicates that completions for all Non-Posted requests have been received. 7:1 0 Reserved Initiate Function Level Reset — RO. This bit is used to initiate an FLT transition. A write of ‘1’ initiates the transition. Since hardware must not respond to any cycles until Function Level Reset completion, the value read by software from this bit is 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 423 Gigabit LAN Configuration Registers 12.2 MBARA—Gigabit LAN Base Address A Registers The internal CSR registers and memories are accessed as direct memory mapped offsets from the base address register. This block is mapped into memory space, using the MBARA Base Address register see Section 12.1.10. SW may only access whole DWord at a time. Table 12-2. Gigabit LAN Base Address A Registers Address Map (Gigabit LAN— D25:F0) 12.2.1 MBARA+Offset Mnemonic Register Name Default Type 00–03h LDR4 LAN Device Initialization 4 14200100h R/W 08–0Bh LDR3 LAN Device Initialization 3 00080xxxh RO 18–1Bh LDCR2 LAN Device Control 2 01500000h R/W 20–23h LDCR4 LAN Device Control 4 1000xxxxh R/W F00h-F03h LDCR5 LAN Device Control 5 00000000h R/W 3004–3007h LDR2 LAN Device Initialization 2 B2B577CCh R/W 3024-3027h LDR1 LAN Device Initialization 1 600060006h R/W LDR4—LAN Device Initialization Register 4 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + 0h Default Value: 14200100h Bit 31:25 24 23:0 12.2.2 Attribute: Size: RO 32 bits Description Reserved LDR4 Field 1 — R/W. BIOS may set this bit to 1. Reserved LDR3—LAN Device Initialization Register 3 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + 8h Default Value: 00080xxxh Bit 31 30:0 424 Attribute: Size: RO 32 bits Description LDR3 Field 1 — RO. When set, this bit enables the automatic reduction of DMA frequency. This bit is loaded from word 13h in the NVM. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet Gigabit LAN Configuration Registers 12.2.3 LDCR2—LAN Device Control Register 2 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + 18h Default Value: 01500000h Bit 31:21 20 Attribute: Size: R/W 32 bits Description Reserved LAN PHY Power Down Enable (LPPDE) — R/W. When set, enables the PHY to enter a low-power state when the LAN controller is at the DMoff / D3 or Dr and no WoL. This bit is loaded from word 13h in the NVM. 19 19:0 12.2.4 LDCR2 Field 1 — R/W. This bit is loaded from word 13h in the NVM. Reserved LDCR4—LAN Device Control Register 4 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + 20h Default Value: 1000xxxxh Bit 31:0 12.2.5 Attribute: Size: R/W 32 bits Description BIOS may program this field. LDR5—LAN Device Control Register 5 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + F00h Default Value: 00000000h Bit 31:6 5 4:0 12.2.6 Attribute: Size: R/W 32 bits Description Reserved LDCR5 Field 1 — R/W. BIOS may set this bit. Reserved LDR2—LAN Device Initialization Register 1 (Gigabit LAN Memory Mapped Base Address Register) Address Offset: MBARA + 3024h Default Value: 60006006h Bit 31:17 16 15:0 Attribute: Size: R/W 32 bits Description Reserved LDR1 Field 1 — R/W. BIOS must program this field to 1b. Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 425 Gigabit LAN Configuration Registers § §§ 426 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13 LPC Interface Bridge Registers (D31:F0) The LPC bridge function of the ICH9 resides in PCI Device 31:Function 0. This function contains many other functional units, such as DMA and Interrupt controllers, Timers, Power Management, System Management, GPIO, RTC, and LPC Configuration Registers. Registers and functions associated with other functional units (EHCI, UHCI, etc.) are described in their respective sections. 13.1 PCI Configuration Registers (LPC I/F—D31:F0) Note: Address locations that are not shown should be treated as Reserved. . Table 13-1. LPC Interface PCI Register Address Map (LPC I/F—D31:F0) (Sheet 1 of 2) Offset Mnemonic 00h–01h VID 02h–03h DID 04h–05h PCICMD PCI Command 06h–07h PCISTS PCI Status 08h RID Register Name Default Type Vendor Identification 8086h RO Device Identification See register description RO 0007h R/W, RO 0210h R/WC, RO See register description RO Revision Identification 09h PI Programming Interface 00h RO 0Ah SCC Sub Class Code 01h RO 0Bh BCC Base Class Code 06h RO 0Dh PLT Primary Latency Timer 00h RO 0Eh HEADTYP 2Ch–2Fh SS 34h CAPP 40h–43h PMBASE Header Type Sub System Identifiers Capability List Pointer ACPI Base Address 44h ACPI_CNTL ACPI Control 48h–4Bh GPIOBASE GPIO Base Address 4C GC 60h–63h PIRQ[n]_ROUT 64h SIRQ_CNTL 68h–6Bh PIRQ[n]_ROUT 6C–6Dh LPC_IBDF 80h LPC_I/O_DEC 82h–83h LPC_EN 84h–87h GEN1_DEC Intel® I/O Controller Hub 9 (ICH9) Family Datasheet GPIO Control PIRQ[A–D] Routing Control Serial IRQ Control 80h RO 00000000h R/WO E0h RO 00000001h R/W, RO 00h R/W 00000001h R/W, RO 00h R/W 80808080h R/W 10h R/W, RO 80808080h R/W IOxAPIC Bus:Device:Function 00F8h R/W I/O Decode Ranges 0000h R/W 0000h R/W 00000000h R/W PIRQ[E–H] Routing Control LPC I/F Enables LPC I/F Generic Decode Range 1 427 LPC Interface Bridge Registers (D31:F0) Table 13-1. LPC Interface PCI Register Address Map (LPC I/F—D31:F0) (Sheet 2 of 2) Offset Mnemonic 88h–8Bh GEN2_DEC 8Ch–8Eh 90h–93h Default Type LPC I/F Generic Decode Range 2 00000000h R/W GEN3_DEC LPC I/F Generic Decode Range 3 00000000h R/W GEN4_DEC LPC I/F Generic Decode Range 4 00000000h R/W Firmware Hub Select 1 00112233h R/W, RO Firmware Hub Select 2 4567h R/W Firmware Hub Decode Enable 1 FFCFh R/W, RO 00h R/WLO, R/W, RO 0009h RO Power Management (See Section 13.8.1) A0h–CFh D0h–D3h 13.1.1 Register Name FWH_SEL1 D4h–D5h FWH_SEL2 D8h–D9h FWH_DEC_EN1 DCh BIOS_CNTL E0h-E1h FDCAP Feature Detection Capability ID E2h FDLEN Feature Detection Capability Length 0Ch RO E3h FDVER Feature Detection Version 10h RO E4h-EBh FDVCT Feature Vector See Description RO F0h-F3h RCBA Root Complex Base Address 00000000h R/W BIOS Control VID—Vendor Identification Register (LPC I/F—D31:F0) Offset Address: 00h–01h Default Value: 8086h Lockable: No Bit 15:0 13.1.2 RO 16-bit Core Description Vendor ID — RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h DID—Device Identification Register (LPC I/F—D31:F0) Offset Address: 02h–03h Default Value: See bit description Lockable: No 428 Attribute: Size: Power Well: Attribute: Size: Power Well: RO 16-bit Core Bit Description 15:0 Device ID — RO. This is a 16-bit value assigned to the Intel® ICH9 LPC bridge. Refer to the Intel® I/O Controller Hub (ICH9) Family Specification Update for the value of the Device ID Register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.3 PCICMD—PCI COMMAND Register (LPC I/F—D31:F0) Offset Address: 04h–05h Default Value: 0007h Lockable: No Bit 15:10 Attribute: Size: Power Well: R/W, RO 16-bit Core Description Reserved 9 Fast Back to Back Enable (FBE) — RO. Hardwired to 0. 8 SERR# Enable (SERR_EN) — R/W. The LPC bridge generates SERR# if this bit is set. 7 Wait Cycle Control (WCC) — RO. Hardwired to 0. Parity Error Response Enable (PERE) — R/W. 6 0 = No action is taken when detecting a parity error. 1 = Enables the ICH9 LPC bridge to respond to parity errors detected on backbone interface. 5 VGA Palette Snoop (VPS) — RO. Hardwired to 0. 4 Memory Write and Invalidate Enable (MWIE) — RO. Hardwired to 0. 3 Special Cycle Enable (SCE) — RO. Hardwired to 0. 2 Bus Master Enable (BME) — RO. Bus Masters cannot be disabled. 1 Memory Space Enable (MSE) — RO. Memory space cannot be disabled on LPC. 0 I/O Space Enable (IOSE) — RO. I/O space cannot be disabled on LPC. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 429 LPC Interface Bridge Registers (D31:F0) 13.1.4 PCISTS—PCI Status Register (LPC I/F—D31:F0) Offset Address: 06h–07h Default Value: 0210h Lockable: No Note: Attribute: Size: Power Well: RO, R/WC 16-bit Core For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit Description 15 Detected Parity Error (DPE) — R/WC. Set when the LPC bridge detects a parity error on the internal backbone. Set even if the PCICMD.PERE bit (D31:F0:04, bit 6) is 0 0 = Parity Error Not detected. 1 = Parity Error detected. 14 Signaled System Error (SSE)— R/WC. Set when the LPC bridge signals a system error to the internal SERR# logic. Master Abort Status (RMA) — R/WC. 13 0 = Unsupported request status not received. 1 = The bridge received a completion with unsupported request status from the backbone. Received Target Abort (RTA) — R/WC. 12 0 = Completion abort not received. 1 = Completion with completion abort received from the backbone. 11 0 = Target abort Not generated on the backbone. 1 = LPC bridge generated a completion packet with target abort status on the backbone. Signaled Target Abort (STA) — R/WC. 10:9 DEVSEL# Timing Status (DEV_STS) — RO. 01 = Medium Timing. Data Parity Error Detected (DPED) — R/WC. 8 • • • LPC bridge receives a completion packet from the backbone from a previous request, Parity error has been detected (D31:F0:06, bit 15) PCICMD.PERE bit (D31:F0:04, bit 6) is set. 7 Fast Back to Back Capable (FBC): Reserved – bit has no meaning on the internal backbone. 6 Reserved. 5 66 MHz Capable (66MHZ_CAP) — Reserved – bit has no meaning on the internal backbone. 4 Capabilities List (CLIST) — RO. Capability list exists on the LPC bridge. 3 Interrupt Status (IS) — RO. The LPC bridge does not generate interrupts. 2:0 430 0 = All conditions listed below Not met. 1 = Set when all three of the following conditions are met: Reserved. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.5 RID—Revision Identification Register (LPC I/F—D31:F0) Offset Address: 08h Default Value: See bit description Bit 7:0 13.1.6 RO 8 bits Description Revision ID (RID) — RO. Refer to the Intel® I/O Controller Hub (ICH9) Family Specification Update for the value of the Revision ID Register PI—Programming Interface Register (LPC I/F—D31:F0) Offset Address: 09h Default Value: 00h Bit 7:0 13.1.7 Attribute: Size: Attribute: Size: RO 8 bits Description Programming Interface — RO. SCC—Sub Class Code Register (LPC I/F—D31:F0) Offset Address: 0Ah Default Value: 01h Bit 7:0 Attribute: Size: RO 8 bits Description Sub Class Code — RO. 8-bit value that indicates the category of bridge for the LPC bridge. 01h = PCI-to-ISA bridge. 13.1.8 BCC—Base Class Code Register (LPC I/F—D31:F0) Offset Address: 0Bh Default Value: 06h Bit 7:0 Attribute: Size: RO 8 bits Description Base Class Code — RO. 8-bit value that indicates the type of device for the LPC bridge. 06h = Bridge device. 13.1.9 PLT—Primary Latency Timer Register (LPC I/F—D31:F0) Offset Address: 0Dh Default Value: 00h Bit Attribute: Size: RO 8 bits Description 7:3 Master Latency Count (MLC) — Reserved. 2:0 Reserved. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 431 LPC Interface Bridge Registers (D31:F0) 13.1.10 HEADTYP—Header Type Register (LPC I/F—D31:F0) Offset Address: 0Eh Default Value: 80h Bit 7 6:0 13.1.11 Attribute: Size: RO 8 bits Description Multi-Function Device — RO. This bit is 1 to indicate a multi-function device. Header Type — RO. This 7-bit field identifies the header layout of the configuration space. SS—Sub System Identifiers Register (LPC I/F—D31:F0) Offset Address: 2Ch–2Fh Default Value: 00000000h Attribute: Size: R/WO 32 bits This register is initialized to logic 0 by the assertion of PLTRST#. This register can be written only once after PLTRST# de-assertion. Bit Description 31:16 Subsystem ID (SSID) — R/WO. This is written by BIOS. No hardware action taken on this value. 15:0 13.1.12 Subsystem Vendor ID (SSVID) — R/WO. This is written by BIOS. No hardware action taken on this value. CAPP—Capability List Pointer (LPC I/F—D31:F0) Offset Address: 34h Default Value: E0h 13.1.13 Attribute: Size: RO 8 bits Bit Description 7:0 Capability Pointer (CP) — RO. Indicates the offset of the of the first capability item. PMBASE—ACPI Base Address Register (LPC I/F—D31:F0) Offset Address: 40h–43h Default Value: 00000001h Lockable: No Attribute: Size: Usage: Power Well: R/W, RO 32 bit ACPI, Legacy Core Sets base address for ACPI I/O registers, GPIO registers and TCO I/O registers. These registers can be mapped anywhere in the 64-K I/O space on 128-byte boundaries. Bit 31:16 15:7 6:1 0 432 Description Reserved Base Address — R/W. This field provides 128 bytes of I/O space for ACPI, GPIO, and TCO logic. This is placed on a 128-byte boundary. Reserved Resource Type Indicator (RTE) — RO. Hardwired to 1 to indicate I/O space. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.14 ACPI_CNTL—ACPI Control Register (LPC I/F — D31:F0) Offset Address: 44h Default Value: 00h Lockable: No Attribute: Size: Usage: Power Well: Bit R/W 8 bit ACPI, Legacy Core Description ACPI Enable (ACPI_EN) — R/W. 7 6:3 0 = Disable. 1 = Decode of the I/O range pointed to by the ACPI base register is enabled, and the ACPI power management function is enabled. Note that the APM power management ranges (B2/B3h) are always enabled and are not affected by this bit. Reserved SCI IRQ Select (SCI_IRQ_SEL) — R/W. Specifies on which IRQ the SCI will internally appear. If not using the APIC, the SCI must be routed to IRQ9–11, and that interrupt is not sharable with the SERIRQ stream, but is shareable with other PCI interrupts. If using the APIC, the SCI can also be mapped to IRQ20–23, and can be shared with other interrupts. 2:0 Bits SCI Map 000b IRQ9 001b IRQ10 010b IRQ11 011b Reserved 100b IRQ20 (Only available if APIC enabled) 101b IRQ21 (Only available if APIC enabled) When the interrupt is mapped to APIC interrupts 9, 10 or 11, the APIC should be programmed for active-high reception. When the interrupt is mapped to APIC interrupts 20 through 23, the APIC should be programmed for active-low reception. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 433 LPC Interface Bridge Registers (D31:F0) 13.1.15 GPIOBASE—GPIO Base Address Register (LPC I/F — D31:F0) Offset Address: 48h–4Bh Default Value: 00000001h Bit 31:16 15:7 (Mobile Only) Attribute: Size: R/W, RO 32 bit Description Reserved. Always 0. Base Address (BA) — R/W. Provides the 128 bytes of I/O space for GPIO. 15:6 (Desktop Only) 6:1 (Mobile Only) Base Address (BA) — R/W. Provides the 64 bytes of I/O space for GPIO. Reserved. Always 0. 5:1 (Desktop Only) 0 434 Reserved. Always 0. RO. Hardwired to 1 to indicate I/O space. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.16 GC—GPIO Control Register (LPC I/F — D31:F0) Offset Address: 4Ch Default Value: 00h Bit 7:5 4 3:1 Attribute: Size: R/W 8 bit Description Reserved. GPIO Enable (EN) — R/W. This bit enables/disables decode of the I/O range pointed to by the GPIO Base Address register (D31:F0:48h) and enables the GPIO function. 0 = Disable. 1 = Enable. Reserved. GPIO Lockdown Enable (GLE) — R/W. This bit enables lockdown of the following GPIO registers: 0 • • • • • • Offset Offset Offset Offset Offset Offset 00h: GPIO_USE_SEL[31:0] 04h: GP_IO_SEL[31:0] 0Ch: GP_LVL[31:0] 30h: GPIO_USE_SEL[63:32] 34h: GP_IO_SEL[63:32] 38h: GP_LVL[63:32] 0 = Disable. 1 = Enable. When this bit is written from a ‘1’ to a ‘0’ an SMI# is generated if enabled. This ensures that only SMM code can change the above GPIO registers after they are locked down. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 435 LPC Interface Bridge Registers (D31:F0) 13.1.17 PIRQ[n]_ROUT—PIRQ[A,B,C,D] Routing Control Register (LPC I/F—D31:F0) Offset Address: PIRQA – 60h, PIRQB – 61h, Attribute: PIRQC – 62h, PIRQD – 63h Default Value: 80h Size: Lockable: No Power Well: Bit R/W 8 bit Core Description Interrupt Routing Enable (IRQEN) — R/W. 7 0 = The corresponding PIRQ is routed to one of the ISA-compatible interrupts specified in bits[3:0]. 1 = The PIRQ is not routed to the 8259. NOTE: BIOS must program this bit to 0 during POST for any of the PIRQs that are being used. The value of this bit may subsequently be changed by the OS when setting up for I/O APIC interrupt delivery mode. 6:4 Reserved IRQ Routing — R/W. (ISA compatible.) 3:0 436 Value IRQ Value IRQ 0000b Reserved 1000b Reserved 0001b Reserved 1001b IRQ9 0010b Reserved 1010b IRQ10 0011b IRQ3 1011b IRQ11 0100b IRQ4 1100b IRQ12 0101b IRQ5 1101b Reserved 0110b IRQ6 1110b IRQ14 0111b IRQ7 1111b IRQ15 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.18 SIRQ_CNTL—Serial IRQ Control Register (LPC I/F—D31:F0) Offset Address: 64h Default Value: 10h Lockable: No Bit Attribute: Size: Power Well: R/W, RO 8 bit Core Description Serial IRQ Enable (SIRQEN) — R/W. 7 0 = The buffer is input only and internally SERIRQ will be a 1. 1 = Serial IRQs will be recognized. The SERIRQ pin will be configured as SERIRQ. Serial IRQ Mode Select (SIRQMD) — R/W. 6 0 = The serial IRQ machine will be in quiet mode. 1 = The serial IRQ machine will be in continuous mode. NOTE: For systems using Quiet Mode, this bit should be set to 1 (Continuous Mode) for at least one frame after coming out of reset before switching back to Quiet Mode. Failure to do so will result in the ICH9 not recognizing SERIRQ interrupts. 5:2 1:0 Serial IRQ Frame Size (SIRQSZ) — RO. Fixed field that indicates the size of the SERIRQ frame as 21 frames. Start Frame Pulse Width (SFPW) — R/W. This is the number of PCI clocks that the SERIRQ pin will be driven low by the serial IRQ machine to signal a start frame. In continuous mode, the ICH9 will drive the start frame for the number of clocks specified. In quiet mode, the ICH9 will drive the start frame for the number of clocks specified minus one, as the first clock was driven by the peripheral. 00 = 4 clocks 01 = 6 clocks 10 = 8 clocks 11 = Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 437 LPC Interface Bridge Registers (D31:F0) 13.1.19 PIRQ[n]_ROUT—PIRQ[E,F,G,H] Routing Control Register (LPC I/F—D31:F0) Offset Address: PIRQE – 68h, PIRQF – 69h, Attribute: PIRQG – 6Ah, PIRQH – 6Bh Default Value: 80h Size: Lockable: No Power Well: Bit R/W 8 bit Core Description Interrupt Routing Enable (IRQEN) — R/W. 7 0 = The corresponding PIRQ is routed to one of the ISA-compatible interrupts specified in bits[3:0]. 1 = The PIRQ is not routed to the 8259. NOTE: BIOS must program this bit to 0 during POST for any of the PIRQs that are being used. The value of this bit may subsequently be changed by the OS when setting up for I/O APIC interrupt delivery mode. 6:4 Reserved IRQ Routing — R/W. (ISA compatible.) 3:0 438 Value IRQ Value IRQ 0000b Reserved 1000b Reserved 0001b Reserved 1001b IRQ9 0010b Reserved 1010b IRQ10 0011b IRQ3 1011b IRQ11 0100b IRQ4 1100b IRQ12 0101b IRQ5 1101b Reserved 0110b IRQ6 1110b IRQ14 0111b IRQ7 1111b IRQ15 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.20 LPC_IBDF—IOxAPIC Bus:Device:Function (LPC I/F—D31:F0) Offset Address: 6Ch-6Dh Default Value: 00F8h Bit Attribute: Size: R/W 16 bit Description IOxAPIC Bus:Device:Function (IBDF)— R/W. this field specifies the bus:device:function that ICH9’s IOxAPIC will be using for the following: • • As the Requester ID when initiating Interrupt Messages to the processor. As the Completer ID when responding to the reads targeting the IOxAPIC’s Memory-Mapped I/ O registers. The 16-bit field comprises the following: Bits 15:0 15:8 Description Bus Number 7:3 Device Number 2:0 Function Number This field defaults to Bus 0: Device 31: Function 0 after reset. BIOS can program this field to provide a unique bus:device:function number for the internal IOxAPIC. 13.1.21 LPC_I/O_DEC—I/O Decode Ranges Register (LPC I/F—D31:F0) Offset Address: 80h Default Value: 0000h Bit 15:13 Attribute: Size: R/W 16 bit Description Reserved FDD Decode Range — R/W. Determines which range to decode for the FDD Port 12 11:10 0 = 3F0h – 3F5h, 3F7h (Primary) 1 = 370h – 375h, 377h (Secondary) Reserved LPT Decode Range — R/W. This field determines which range to decode for the LPT Port. 9:8 7 00 01 10 11 = = = = 378h – 37Fh and 778h – 77Fh 278h – 27Fh (port 279h is read only) and 678h – 67Fh 3BCh –3BEh and 7BCh – 7BEh Reserved Reserved Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 439 LPC Interface Bridge Registers (D31:F0) Bit Description COMB Decode Range — R/W. This field determines which range to decode for the COMB Port. 000 = 3F8h – 3FFh (COM1) 001 = 2F8h – 2FFh (COM2) 6:4 010 = 220h – 227h 011 = 228h – 22Fh 100 = 238h – 23Fh 101 = 2E8h – 2EFh (COM4) 110 = 338h – 33Fh 111 = 3E8h – 3EFh (COM3) 3 Reserved COMA Decode Range — R/W. This field determines which range to decode for the COMA Port. 000 = 3F8h – 3FFh (COM1) 001 = 2F8h – 2FFh (COM2) 2:0 010 = 220h – 227h 011 = 228h – 22Fh 100 = 238h – 23Fh 101 = 2E8h – 2EFh (COM4) 110 = 338h – 33Fh 111 = 3E8h – 3EFh (COM3) 13.1.22 LPC_EN—LPC I/F Enables Register (LPC I/F—D31:F0) Offset Address: 82h – 83h Default Value: 0000h Bit 15:14 Attribute: Size: Power Well: R/W 16 bit Core Description Reserved CNF2_LPC_EN — R/W. Microcontroller Enable # 2. 13 0 = Disable. 1 = Enables the decoding of the I/O locations 4Eh and 4Fh to the LPC interface. This range is used for a microcontroller. CNF1_LPC_EN — R/W. Super I/O Enable. 12 0 = Disable. 1 = Enables the decoding of the I/O locations 2Eh and 2Fh to the LPC interface. This range is used for Super I/O devices. MC_LPC_EN — R/W. Microcontroller Enable # 1. 11 0 = Disable. 1 = Enables the decoding of the I/O locations 62h and 66h to the LPC interface. This range is used for a microcontroller. KBC_LPC_EN — R/W. Keyboard Enable. 10 440 0 = Disable. 1 = Enables the decoding of the I/O locations 60h and 64h to the LPC interface. This range is used for a microcontroller. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description GAMEH_LPC_EN — R/W. High Gameport Enable 9 0 = Disable. 1 = Enables the decoding of the I/O locations 208h to 20Fh to the LPC interface. This range is used for a gameport. GAMEL_LPC_EN — R/W. Low Gameport Enable 8 7:4 0 = Disable. 1 = Enables the decoding of the I/O locations 200h to 207h to the LPC interface. This range is used for a gameport. Reserved FDD_LPC_EN — R/W. Floppy Drive Enable 3 0 = Disable. 1 = Enables the decoding of the FDD range to the LPC interface. This range is selected in the LPC_FDD/LPT Decode Range Register (D31:F0:80h, bit 12). LPT_LPC_EN — R/W. Parallel Port Enable 2 0 = Disable. 1 = Enables the decoding of the LPTrange to the LPC interface. This range is selected in the LPC_FDD/LPT Decode Range Register (D31:F0:80h, bit 9:8). COMB_LPC_EN — R/W. Com Port B Enable 1 0 = Disable. 1 = Enables the decoding of the COMB range to the LPC interface. This range is selected in the LPC_COM Decode Range Register (D31:F0:80h, bits 6:4). COMA_LPC_EN — R/W. Com Port A Enable 0 13.1.23 0 = Disable. 1 = Enables the decoding of the COMA range to the LPC interface. This range is selected in the LPC_COM Decode Range Register (D31:F0:80h, bits 3:2). GEN1_DEC—LPC I/F Generic Decode Range 1 Register (LPC I/F—D31:F0) Offset Address: 84h – 87h Default Value: 00000000h Bit Attribute: Size: Power Well: R/W 32 bit Core Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask — R/W. A ‘1’ in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 Reserved 15:2 Generic I/O Decode Range 1 Base Address (GEN1_BASE) — R/W. This address is aligned on a 128-byte boundary, and must have address lines 31:16 as 0. NOTE: The ICH Does not provide decode down to the word or byte level 1 Reserved 0 0 = Disable. 1 = Enable the GEN1 I/O range to be forwarded to the LPC I/F Generic Decode Range 1 Enable (GEN1_EN) — R/W. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 441 LPC Interface Bridge Registers (D31:F0) 13.1.24 GEN2_DEC—LPC I/F Generic Decode Range 2 Register (LPC I/F—D31:F0) Offset Address: 88h – 8Bh Default Value: 00000000h Bit Attribute: Size: Power Well: R/W 32 bit Core Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask — R/W. A ‘1’ in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 Reserved 15:2 1 Generic I/O Decode Range 2 Base Address (GEN1_BASE) — R/W. NOTE: The ICH Does not provide decode down to the word or byte level Reserved Generic Decode Range 2 Enable (GEN2_EN) — R/W. 0 13.1.25 0 = Disable. 1 = Enable the GEN2 I/O range to be forwarded to the LPC I/F GEN3_DEC—LPC I/F Generic Decode Range 3 Register (LPC I/F—D31:F0) Offset Address: 8Ch – 8Eh Default Value: 00000000h Bit Attribute: Size: Power Well: R/W 32 bit Core Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask — R/W. A ‘1’ in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 Reserved 15:2 1 Generic I/O Decode Range 3 Base Address (GEN3_BASE) — R/W. NOTE: The ICH Does not provide decode down to the word or byte level Reserved Generic Decode Range 3 Enable (GEN3_EN) — R/W. 0 442 0 = Disable. 1 = Enable the GEN3 I/O range to be forwarded to the LPC I/F Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.26 GEN4_DEC—LPC I/F Generic Decode Range 4 Register (LPC I/F—D31:F0) Offset Address: 90h – 93h Default Value: 00000000h Bit Attribute: Size: Power Well: R/W 32 bit Core Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask — R/W. A ‘1’ in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 Reserved 15:2 Generic I/O Decode Range 4 Base Address (GEN4_BASE) — R/W. NOTE: The ICH Does not provide decode down to the word or byte level 1 Reserved 0 0 = Disable. 1 = Enable the GEN4 I/O range to be forwarded to the LPC I/F Generic Decode Range 4 Enable (GEN4_EN) — R/W. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 443 LPC Interface Bridge Registers (D31:F0) 13.1.27 FWH_SEL1—Firmware Hub Select 1 Register (LPC I/F—D31:F0) Offset Address: D0h–D3h Default Value: 00112233h Bit 31:28 27:24 23:20 19:16 15:12 11:8 7:4 3:0 444 Attribute: Size: R/W, RO 32 bits Description FWH_F8_IDSEL — RO. IDSEL for two 512-KB Firmware Hub memory ranges and one 128-KB memory range. This field is fixed at 0000. The IDSEL programmed in this field addresses the following memory ranges: FFF8 0000h – FFFF FFFFh FFB8 0000h – FFBF FFFFh 000E 0000h – 000F FFFFh FWH_F0_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFF0 0000h – FFF7 FFFFh FFB0 0000h – FFB7 FFFFh FWH_E8_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFE8 0000h – FFEF FFFFh FFA8 0000h – FFAF FFFFh FWH_E0_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFE0 0000h – FFE7 FFFFh FFA0 0000h – FFA7 FFFFh FWH_D8_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFD8 0000h – FFDF FFFFh FF98 0000h – FF9F FFFFh FWH_D0_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFD0 0000h – FFD7 FFFFh FF90 0000h – FF97 FFFFh FWH_C8_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFC8 0000h – FFCF FFFFh FF88 0000h – FF8F FFFFh FWH_C0_IDSEL — R/W. IDSEL for two 512-KB Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFC0 0000h – FFC7 FFFFh FF80 0000h – FF87 FFFFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.28 FWH_SEL2—Firmware Hub Select 2 Register (LPC I/F—D31:F0) Offset Address: D4h–D5h Default Value: 4567h Bit 15:12 11:8 7:4 3:0 13.1.29 Attribute: Size: R/W 16 bits Description FWH_70_IDSEL — R/W. IDSEL for two, 1-M Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF70 0000h – FF7F FFFFh FF30 0000h – FF3F FFFFh FWH_60_IDSEL — R/W. IDSEL for two, 1-M Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF60 0000h – FF6F FFFFh FF20 0000h – FF2F FFFFh FWH_50_IDSEL — R/W. IDSEL for two, 1-M Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF50 0000h – FF5F FFFFh FF10 0000h – FF1F FFFFh FWH_40_IDSEL — R/W. IDSEL for two, 1-M Firmware Hub memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF40 0000h – FF4F FFFFh FF00 0000h – FF0F FFFFh FWH_DEC_EN1—Firmware Hub Decode Enable Register (LPC I/F—D31:F0) Offset Address: D8h–D9h Default Value: FFCFh Bit Attribute: Size: R/W, RO 16 bits Description FWH_F8_EN — RO. This bit enables decoding two 512-KB Firmware Hub memory ranges, and one 128-KB memory range. 15 0 = Disable 1 = Enable the following ranges for the Firmware Hub FFF80000h – FFFFFFFFh FFB80000h – FFBFFFFFh FWH_F0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 14 0 = Disable. 1 = Enable the following ranges for the Firmware Hub: FFF00000h – FFF7FFFFh FFB00000h – FFB7FFFFh FWH_E8_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 13 0 = Disable. 1 = Enable the following ranges for the Firmware Hub: FFE80000h – FFEFFFFh FFA80000h – FFAFFFFFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 445 LPC Interface Bridge Registers (D31:F0) Bit Description FWH_E0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 12 0 = Disable. 1 = Enable the following ranges for the Firmware Hub: FFE00000h – FFE7FFFFh FFA00000h – FFA7FFFFh FWH_D8_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 11 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFD80000h – FFDFFFFFh FF980000h – FF9FFFFFh FWH_D0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 10 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFD00000h – FFD7FFFFh FF900000h – FF97FFFFh FWH_C8_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 9 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFC80000h – FFCFFFFFh FF880000h – FF8FFFFFh FWH_C0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 8 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFC00000h – FFC7FFFFh FF800000h – FF87FFFFh FWH_Legacy_F_EN — R/W. This enables the decoding of the legacy 64KB range at F0000h – FFFFFh. 7 0 = Disable. 1 = Enable the following legacy ranges for the Firmware Hub F0000h – FFFFFh Note: The decode for the BIOS legacy F segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. FWH_Legacy_E_EN — R/W. This enables the decoding of the legacy 64KB range at E0000h – EFFFFh. 6 0 = Disable. 1 = Enable the following legacy ranges for the Firmware Hub E0000h – EFFFFh Note: The decode for the BIOS legacy E segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. 5:4 Reserved FWH_70_EN — R/W. Enables decoding two 1-M Firmware Hub memory ranges. 3 446 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FF70 0000h – FF7F FFFFh FF30 0000h – FF3F FFFFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description FWH_E0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 12 0 = Disable. 1 = Enable the following ranges for the Firmware Hub: FFE00000h – FFE7FFFFh FFA00000h – FFA7FFFFh FWH_D8_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 11 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFD80000h – FFDFFFFFh FF980000h – FF9FFFFFh FWH_D0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 10 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFD00000h – FFD7FFFFh FF900000h – FF97FFFFh FWH_C8_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 9 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFC80000h – FFCFFFFFh FF880000h – FF8FFFFFh FWH_C0_EN — R/W. This bit enables decoding two 512-KB Firmware Hub memory ranges. 8 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FFC00000h – FFC7FFFFh FF800000h – FF87FFFFh FWH_Legacy_F_EN — R/W. This enables the decoding of the legacy 64KB range at F0000h – FFFFFh. 7 0 = Disable. 1 = Enable the following legacy ranges for the Firmware Hub F0000h – FFFFFh Note: The decode for the BIOS legacy F segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. FWH_Legacy_E_EN — R/W. This enables the decoding of the legacy 64KB range at E0000h – EFFFFh. 6 0 = Disable. 1 = Enable the following legacy ranges for the Firmware Hub E0000h – EFFFFh Note: The decode for the BIOS legacy E segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. 5:4 Reserved FWH_70_EN — R/W. Enables decoding two 1-M Firmware Hub memory ranges. 3 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FF70 0000h – FF7F FFFFh FF30 0000h – FF3F FFFFh Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 447 LPC Interface Bridge Registers (D31:F0) Bit Description FWH_60_EN — R/W. Enables decoding two 1-M Firmware Hub memory ranges. 2 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FF60 0000h – FF6F FFFFh FF20 0000h – FF2F FFFFh FWH_50_EN — R/W. Enables decoding two 1-M Firmware Hub memory ranges. 1 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FF50 0000h – FF5F FFFFh FF10 0000h – FF1F FFFFh FWH_40_EN — R/W. Enables decoding two 1-M Firmware Hub memory ranges. 0 0 = Disable. 1 = Enable the following ranges for the Firmware Hub FF40 0000h – FF4F FFFFh FF00 0000h – FF0F FFFFh NOTE: This register effects the BIOS decode regardless of whether the BIOS is resident on LPC or SPI. The concept of Feature Space does not apply to SPI-based flash. The ICH simply decodes these ranges as memory accesses when enabled for the SPI flash interface. 448 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.30 BIOS_CNTL—BIOS Control Register (LPC I/F—D31:F0) Offset Address: DCh Default Value: 00h Lockable: No Attribute: Size: Power Well: Bit 7:5 4 R/WLO, R/W, RO 8 bit Core Description Reserved Top Swap Status (TSS) — RO. This bit provides a read-only path to view the state of the Top Swap bit that is at offset 3414h, bit 0. SPI Read Configuration (SRC) — R/W. This 2-bit field controls two policies related to BIOS reads on the SPI interface: Bit 3- Prefetch Enable Bit 2- Cache Disable Settings are summarized below: Bits 3:2 3:2 Description 00b No prefetching, but caching enabled. 64B demand reads load the read buffer cache with “valid” data, allowing repeated code fetches to the same line to complete quickly 01b No prefetching and no caching. One-to-one correspondence of host BIOS reads to SPI cycles. This value can be used to invalidate the cache. 10b Prefetching and Caching enabled. This mode is used for long sequences of short reads to consecutive addresses (i.e., shadowing). 11b Reserved. This is an invalid configuration, caching must be enabled when prefetching is enabled. BIOS Lock Enable (BLE) — R/WLO. 1 0 = Setting the BIOSWE will not cause SMIs. 1 = Enables setting the BIOSWE bit to cause SMIs. Once set, this bit can only be cleared by a PLTRST# BIOS Write Enable (BIOSWE) — R/W. 0 0 = Only read cycles result in Firmware Hub I/F cycles. 1 = Access to the BIOS space is enabled for both read and write cycles. When this bit is written from a 0 to a 1 and BIOS Lock Enable (BLE) is also set, an SMI# is generated. This ensures that only SMI code can update BIOS. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 449 LPC Interface Bridge Registers (D31:F0) 13.1.31 FDCAP—Feature Detection Capability ID (LPC I/F—D31:F0) Offset Address: E0h-E1h Default Value: 0009h Bit 13.1.32 15:8 Next Item Pointer (NEXT) — RO. Configuration offset of the next Capability Item. 00h indicates the last item in the Capability List. 7:0 Capability ID — RO. Indicates a Vendor Specific Capability FDLEN—Feature Detection Capability Length (LPC I/F—D31:F0) Bit 7:0 Attribute: Size: Power Well: RO 8 bit Core Description Capability Length — RO. Indicates the length of this Vendor Specific capability, as required by PCI Spec. FDVER—Feature Detection Version (LPC I/F—D31:F0) Offset Address: E3h Default Value: 10h Bit 450 RO 16 bit Core Description Offset Address: E2h Default Value: 0Ch 13.1.33 Attribute: Size: Power Well: Attribute: Size: Power Well: RO 8 bit Core Description 7:4 Vendor-Specific Capability ID — RO. A value of 1h in this 4-bit field identifies this Capability as Feature Detection Type. This field allows software to differentiate the Feature Detection Capability from other Vendor-Specific capabilities 3:0 Capability Version — RO. This field indicates the version of the Feature Detection capability Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.1.34 FDVCT—Feature Vector (LPC I/F—D31:F0) Offset Address: E4h-EBh Default Value: See Description Bit Attribute: Size: Power Well: RO 64 bit Core Description 63:39 Reserved Intel Active Management Technology Capability — RO. 38:37 00 = Capable 11 = Disabled 36:28 Reserved Desktop SATA Ports 2 & 3 Capability — RO. 27 0 = Capable 1 = Disabled 26:10 Reserved 9 (Desktop Only) Reserved 9 (Mobile Only) 8:6 Mobile Features Capability— RO. 0 = Disabled 1 = Capable Reserved SATA RAID 0/1/5/10 Capability— RO: 5 0 = Capable 1 = Disabled 4:0 13.1.35 Reserved RCBA—Root Complex Base Address Register (LPC I/F—D31:F0) Offset Address: F0-F3h Default Value: 00000000h Attribute: Size: R/W 32 bit Bit Description 31:14 Base Address (BA) — R/W. Base Address for the root complex register block decode range. This address is aligned on a 16-KB boundary. 13:1 0 Reserved Enable (EN) — R/W. When set, enables the range specified in BA to be claimed as the Root Complex Register Block. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 451 LPC Interface Bridge Registers (D31:F0) 13.2 DMA I/O Registers (LPC I/F—D31:F0) Table 13-2. DMA Registers (Sheet 1 of 2) Port 452 Alias Register Name Default Type 00h 10h Channel 0 DMA Base & Current Address Undefined R/W 01h 11h Channel 0 DMA Base & Current Count Undefined R/W 02h 12h Channel 1 DMA Base & Current Address Undefined R/W 03h 13h Channel 1 DMA Base & Current Count Undefined R/W 04h 14h Channel 2 DMA Base & Current Address Undefined R/W 05h 15h Channel 2 DMA Base & Current Count Undefined R/W 06h 16h Channel 3 DMA Base & Current Address Undefined R/W 07h 17h Channel 3 DMA Base & Current Count Undefined R/W 08h 18h Channel 0–3 DMA Command Undefined WO Channel 0–3 DMA Status Undefined RO 0Ah 1Ah Channel 0–3 DMA Write Single Mask 000001XXb WO 0Bh 1Bh Channel 0–3 DMA Channel Mode 000000XXb WO 0Ch 1Ch Channel 0–3 DMA Clear Byte Pointer Undefined WO 0Dh 1Dh Channel 0–3 DMA Master Clear Undefined WO 0Eh 1Eh Channel 0–3 DMA Clear Mask Undefined WO 0Fh 1Fh Channel 0–3 DMA Write All Mask 0Fh R/W 80h 90h Reserved Page Undefined R/W 81h 91h Channel 2 DMA Memory Low Page Undefined R/W 82h — Channel 3 DMA Memory Low Page Undefined R/W 83h 93h Channel 1 DMA Memory Low Page Undefined R/W 84h–86h 94h–96h Reserved Pages Undefined R/W 87h 97h Channel 0 DMA Memory Low Page Undefined R/W 88h 98h Reserved Page Undefined R/W 89h 99h Channel 6 DMA Memory Low Page Undefined R/W 8Ah 9Ah Channel 7 DMA Memory Low Page Undefined R/W 8Bh 9Bh Channel 5 DMA Memory Low Page Undefined R/W 8Ch–8Eh 9Ch–9Eh Reserved Page Undefined R/W 8Fh 9Fh Refresh Low Page Undefined R/W C0h C1h Channel 4 DMA Base & Current Address Undefined R/W C2h C3h Channel 4 DMA Base & Current Count Undefined R/W C4h C5h Channel 5 DMA Base & Current Address Undefined R/W C6h C7h Channel 5 DMA Base & Current Count Undefined R/W C8h C9h Channel 6 DMA Base & Current Address Undefined R/W CAh CBh Channel 6 DMA Base & Current Count Undefined R/W CCh CDh Channel 7 DMA Base & Current Address Undefined R/W Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) Table 13-2. DMA Registers (Sheet 2 of 2) 13.2.1 Port Alias CEh CFh D0h D1h Register Name Default Type Channel 7 DMA Base & Current Count Undefined R/W Channel 4–7 DMA Command Undefined WO Channel 4–7 DMA Status Undefined RO D4h D5h Channel 4–7 DMA Write Single Mask 000001XXb WO D6h D7h Channel 4–7 DMA Channel Mode 000000XXb WO D8h D9h Channel 4–7 DMA Clear Byte Pointer Undefined WO DAh DBh Channel 4–7 DMA Master Clear Undefined WO DCh DDh Channel 4–7 DMA Clear Mask Undefined WO DEh DFh Channel 4–7 DMA Write All Mask 0Fh R/W DMABASE_CA—DMA Base and Current Address Registers (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0 = 00h; Ch. #1 = 02h Ch. #2 = 04h; Ch. #3 = 06h Ch. #5 = C4h Ch. #6 = C8h Ch. #7 = CCh; Undefined No Bit Attribute: R/W Size: 16 bit (per channel), but accessed in two 8-bit quantities Power Well:Core Description Base and Current Address — R/W. This register determines the address for the transfers to be performed. The address specified points to two separate registers. On writes, the value is stored in the Base Address register and copied to the Current Address register. On reads, the value is returned from the Current Address register. 15:0 The address increments/decrements in the Current Address register after each transfer, depending on the mode of the transfer. If the channel is in auto-initialize mode, the Current Address register will be reloaded from the Base Address register after a terminal count is generated. For transfers to/from a 16-bit slave (channel’s 5-7), the address is shifted left one bit location. Bit 15 will be shifted into Bit 16. The register is accessed in 8 bit quantities. The byte is pointed to by the current byte pointer flip/flop. Before accessing an address register, the byte pointer flip/flop should be cleared to ensure that the low byte is accessed first Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 453 LPC Interface Bridge Registers (D31:F0) 13.2.2 DMABASE_CC—DMA Base and Current Count Registers (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Bit Ch. #0 = 01h; Ch. #1 = 03h Ch. #2 = 05h; Ch. #3 = 07h Ch. #5 = C6h; Ch. #6 = CAh Ch. #7 = CEh; Undefined No Attribute: R/W Size: 16-bit (per channel), but accessed in two 8-bit quantities Power Well:Core Description Base and Current Count — R/W. This register determines the number of transfers to be performed. The address specified points to two separate registers. On writes, the value is stored in the Base Count register and copied to the Current Count register. On reads, the value is returned from the Current Count register. 15:0 The actual number of transfers is one more than the number programmed in the Base Count Register (i.e., programming a count of 4h results in 5 transfers). The count is decrements in the Current Count register after each transfer. When the value in the register rolls from 0 to FFFFh, a terminal count is generated. If the channel is in autoinitialize mode, the Current Count register will be reloaded from the Base Count register after a terminal count is generated. For transfers to/from an 8-bit slave (channels 0–3), the count register indicates the number of bytes to be transferred. For transfers to/from a 16-bit slave (channels 5–7), the count register indicates the number of words to be transferred. The register is accessed in 8 bit quantities. The byte is pointed to by the current byte pointer flip/flop. Before accessing a count register, the byte pointer flip/flop should be cleared to ensure that the low byte is accessed first. 13.2.3 DMAMEM_LP—DMA Memory Low Page Registers (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: 454 Ch. #0 = 87h; Ch. #1 = 83h Ch. #2 = 81h; Ch. #3 = 82h Ch. #5 = 8Bh; Ch. #6 = 89h Ch. #7 = 8Ah; Undefined No Attribute: Size: Power Well: R/W 8-bit Core Bit Description 7:0 DMA Low Page (ISA Address bits [23:16]) — R/W. This register works in conjunction with the DMA controller's Current Address Register to define the complete 24-bit address for the DMA channel. This register remains static throughout the DMA transfer. Bit 16 of this register is ignored when in 16 bit I/O count by words mode as it is replaced by the bit 15 shifted out from the current address register. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.2.4 DMACMD—DMA Command Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0–3 = 08h; Ch. #4–7 = D0h Undefined No Bit 7:5 4 Attribute: Size: Power Well: WO 8-bit Core Description Reserved. Must be 0. DMA Group Arbitration Priority — WO. Each channel group is individually assigned either fixed or rotating arbitration priority. At part reset, each group is initialized in fixed priority. 0 = Fixed priority to the channel group 1 = Rotating priority to the group. 3 Reserved. Must be 0. DMA Channel Group Enable — WO. Both channel groups are enabled following part reset. 2 1:0 13.2.5 0 = Enable the DMA channel group. 1 = Disable. Disabling channel group 4–7 also disables channel group 0–3, which is cascaded through channel 4. Reserved. Must be 0. DMASTA—DMA Status Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0–3 = 08h; Ch. #4–7 = D0h Undefined No Attribute: Size: Power Well: RO 8-bit Core Bit Description 7:4 Channel Request Status — RO. When a valid DMA request is pending for a channel, the corresponding bit is set to 1. When a DMA request is not pending for a particular channel, the corresponding bit is set to 0. The source of the DREQ may be hardware or a software request. Note that channel 4 is the cascade channel, so the request status of channel 4 is a logical OR of the request status for channels 0 through 3. 4 = Channel 0 5 = Channel 1 (5) 6 = Channel 2 (6) 7 = Channel 3 (7) Channel Terminal Count Status — RO. When a channel reaches terminal count (TC), its status bit is set to 1. If TC has not been reached, the status bit is set to 0. Channel 4 is programmed for cascade, so the TC bit response for channel 4 is irrelevant: 3:0 0 = Channel 0 1 = Channel 1 (5) 2 = Channel 2 (6) 3 = Channel 3 (7) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 455 LPC Interface Bridge Registers (D31:F0) 13.2.6 DMA_WRSMSK—DMA Write Single Mask Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0–3 = 0Ah; Ch. #4–7 = D4h 0000 01xx No Bit 7:3 Attribute: Size: Power Well: WO 8-bit Core Description Reserved. Must be 0. Channel Mask Select — WO. 2 0 = Enable DREQ for the selected channel. The channel is selected through bits [1:0]. Therefore, only one channel can be masked / unmasked at a time. 1 = Disable DREQ for the selected channel. DMA Channel Select — WO. These bits select the DMA Channel Mode Register to program. 1:0 00 = Channel 0 (4) 01 = Channel 1 (5) 10 = Channel 2 (6) 11 = Channel 3 (7) 456 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.2.7 DMACH_MODE—DMA Channel Mode Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0–3 = 0Bh; Ch. #4–7 = D6h 0000 00xx No Bit Attribute: Size: Power Well: WO 8-bit Core Description DMA Transfer Mode — WO. Each DMA channel can be programmed in one of four different modes: 7:6 00 = Demand mode 01 = Single mode 10 = Reserved 11 = Cascade mode 5 Address Increment/Decrement Select — WO. This bit controls address increment/ decrement during DMA transfers. 0 = Address increment. (default after part reset or Master Clear) 1 = Address decrement. Autoinitialize Enable — WO. 4 0 = Autoinitialize feature is disabled and DMA transfers terminate on a terminal count. A part reset or Master Clear disables autoinitialization. 1 = DMA restores the Base Address and Count registers to the current registers following a terminal count (TC). DMA Transfer Type — WO. These bits represent the direction of the DMA transfer. When the channel is programmed for cascade mode, (bits[7:6] = 11) the transfer type is irrelevant. 3:2 00 = Verify – No I/O or memory strobes generated 01 = Write – Data transferred from the I/O devices to memory 10 = Read – Data transferred from memory to the I/O device 11 = Invalid DMA Channel Select — WO. These bits select the DMA Channel Mode Register that will be written by bits [7:2]. 1:0 00 = Channel 0 (4) 01 = Channel 1 (5) 10 = Channel 2 (6) 11 = Channel 3 (7) Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 457 LPC Interface Bridge Registers (D31:F0) 13.2.8 DMA Clear Byte Pointer Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: 13.2.9 WO 8-bit Core Description 7:0 Clear Byte Pointer — WO. No specific pattern. Command enabled with a write to the I/O port address. Writing to this register initializes the byte pointer flip/flop to a known state. It clears the internal latch used to address the upper or lower byte of the 16-bit Address and Word Count Registers. The latch is also cleared by part reset and by the Master Clear command. This command precedes the first access to a 16-bit DMA controller register. The first access to a 16-bit register will then access the significant byte, and the second access automatically accesses the most significant byte. DMA Master Clear Register (LPC I/F—D31:F0) Default Value: Ch. #0–3 = 0Dh; Ch. #4–7 = DAh xxxx xxxx Attribute: Size: WO 8-bit Bit Description 7:0 Master Clear — WO. No specific pattern. Enabled with a write to the port. This has the same effect as the hardware Reset. The Command, Status, Request, and Byte Pointer flip/flop registers are cleared and the Mask Register is set. DMA_CLMSK—DMA Clear Mask Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: 458 Attribute: Size: Power Well: Bit I/O Address: 13.2.10 Ch. #0–3 = 0Ch; Ch. #4–7 = D8h xxxx xxxx No Ch. #0–3 = 0Eh; Ch. #4–7 = DCh xxxx xxxx No Attribute: Size: Power Well: WO 8-bit Core Bit Description 7:0 Clear Mask Register — WO. No specific pattern. Command enabled with a write to the port. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.2.11 DMA_WRMSK—DMA Write All Mask Register (LPC I/F—D31:F0) I/O Address: Default Value: Lockable: Ch. #0–3 = 0Fh; Ch. #4–7 = DEh 0000 1111 No Bit 7:4 Attribute: Size: Power Well: R/W 8-bit Core Description Reserved. Must be 0. Channel Mask Bits — R/W. This register permits all four channels to be simultaneously enabled/disabled instead of enabling/disabling each channel individually, as is the case with the Mask Register – Write Single Mask Bit. In addition, this register has a read path to allow the status of the channel mask bits to be read. A channel's mask bit is automatically set to 1 when the Current Byte/Word Count Register reaches terminal count (unless the channel is in auto-initialization mode). 3:0 Setting the bit(s) to a 1 disables the corresponding DREQ(s). Setting the bit(s) to a 0 enables the corresponding DREQ(s). Bits [3:0] are set to 1 upon part reset or Master Clear. When read, bits [3:0] indicate the DMA channel [3:0] ([7:4]) mask status. Bit 0 = Channel 0 (4) 1 = Masked, 0 = Not Masked Bit 1 = Channel 1 (5) 1 = Masked, 0 = Not Masked Bit 2 = Channel 2 (6) 1 = Masked, 0 = Not Masked Bit 3 = Channel 3 (7) 1 = Masked, 0 = Not Masked NOTE: Disabling channel 4 also disables channels 0–3 due to the cascade of channel’s 0 – 3 through channel 4. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 459 LPC Interface Bridge Registers (D31:F0) 13.3 Timer I/O Registers (LPC I/F—D31:F0) Port Aliases 40h 50h 41h 51h 42h 43h 52h 53h Register Name Counter 0 Interval Time Status Byte Format Counter 0 Counter Access Port Counter 1 Interval Time Status Byte Format Counter 1 Counter Access Port Type 0XXXXXXXb RO Undefined R/W 0XXXXXXXb RO Undefined R/W 0XXXXXXXb RO Counter 2 Counter Access Port Undefined R/W Timer Control Word Undefined WO XXXXXXX0b WO X0h WO Counter 2 Interval Time Status Byte Format Timer Control Word Register Counter Latch Command 460 Default Value Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.3.1 TCW—Timer Control Word Register (LPC I/F—D31:F0) I/O Address: Default Value: 43h All bits undefined Attribute: Size: WO 8 bits This register is programmed prior to any counter being accessed to specify counter modes. Following part reset, the control words for each register are undefined and each counter output is 0. Each timer must be programmed to bring it into a known state. Bit Description Counter Select — WO. The Counter Selection bits select the counter the control word acts upon as shown below. The Read Back Command is selected when bits[7:6] are both 1. 7:6 00 = Counter 0 select 01 = Counter 1 select 10 = Counter 2 select 11 = Read Back Command Read/Write Select — WO. These bits are the read/write control bits. The actual counter programming is done through the counter port (40h for counter 0, 41h for counter 1, and 42h for counter 2). 5:4 00 = Counter Latch Command 01 = Read/Write Least Significant Byte (LSB) 10 = Read/Write Most Significant Byte (MSB) 11 = Read/Write LSB then MSB Counter Mode Selection — WO. These bits select one of six possible modes of operation for the selected counter. Bit Value 3:1 Mode 000b Mode 0 Out signal on end of count (=0) 001b Mode 1 Hardware retriggerable one-shot x10b Mode 2 Rate generator (divide by n counter) x11b Mode 3 Square wave output 100b Mode 4 Software triggered strobe 101b Mode 5 Hardware triggered strobe Binary/BCD Countdown Select — WO. 0 0 = Binary countdown is used. The largest possible binary count is 216 1 = Binary coded decimal (BCD) count is used. The largest possible BCD count is 104 There are two special commands that can be issued to the counters through this register, the Read Back Command and the Counter Latch Command. When these commands are chosen, several bits within this register are redefined. These register formats are described below: Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 461 LPC Interface Bridge Registers (D31:F0) 13.3.2 RDBK_CMD—Read Back Command (LPC I/F—D31:F0) The Read Back Command is used to determine the count value, programmed mode, and current states of the OUT pin and Null count flag of the selected counter or counters. Status and/or count may be latched in any or all of the counters by selecting the counter during the register write. The count and status remain latched until read, and further latch commands are ignored until the count is read. Both count and status of the selected counters may be latched simultaneously by setting both bit 5 and bit 4 to 0. If both are latched, the first read operation from that counter returns the latched status. The next one or two reads, depending on whether the counter is programmed for one or two byte counts, returns the latched count. Subsequent reads return an unlatched count. Bit 7:6 Description Read Back Command. Must be 11 to select the Read Back Command Latch Count of Selected Counters. 5 0 = Current count value of the selected counters will be latched 1 = Current count will not be latched Latch Status of Selected Counters. 4 0 = Status of the selected counters will be latched 1 = Status will not be latched 3 Counter 2 Select. 1 = Counter 2 count and/or status will be latched 2 Counter 1 Select. 1 = Counter 1 count and/or status will be latched 1 Counter 0 Select. 1 = Counter 0 count and/or status will be latched. 0 Reserved. Must be 0. LTCH_CMD—Counter Latch Command (LPC I/F—D31:F0) The Counter Latch Command latches the current count value. This command is used to insure that the count read from the counter is accurate. The count value is then read from each counter's count register through the Counter Ports Access Ports Register (40h for counter 0, 41h for counter 1, and 42h for counter 2). The count must be read according to the programmed format, i.e., if the counter is programmed for two byte counts, two bytes must be read. The two bytes do not have to be read one right after the other (read, write, or programming operations for other counters may be inserted between the reads). If a counter is latched once and then latched again before the count is read, the second Counter Latch Command is ignored. Bit Description Counter Selection. These bits select the counter for latching. If “11” is written, then the write is interpreted as a read back command. 7:6 00 = Counter 0 01 = Counter 1 10 = Counter 2 5:4 3:0 462 Counter Latch Command. 00 = Selects the Counter Latch Command. Reserved. Must be 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.3.3 SBYTE_FMT—Interval Timer Status Byte Format Register (LPC I/F—D31:F0) I/O Address: Default Value: Counter 0 = 40h, Counter 1 = 41h, Attribute: Counter 2 = 42h Size: Bits[6:0] undefined, Bit 7=0 RO 8 bits per counter Each counter's status byte can be read following a Read Back Command. If latch status is chosen (bit 4=0, Read Back Command) as a read back option for a given counter, the next read from the counter's Counter Access Ports Register (40h for counter 0, 41h for counter 1, and 42h for counter 2) returns the status byte. The status byte returns the following: Bit Description Counter OUT Pin State — RO. 7 6 0 = OUT pin of the counter is also a 0 1 = OUT pin of the counter is also a 1 Count Register Status — RO. This bit indicates when the last count written to the Count Register (CR) has been loaded into the counting element (CE). The exact time this happens depends on the counter mode, but until the count is loaded into the counting element (CE), the count value will be incorrect. 0 = Count has been transferred from CR to CE and is available for reading. 1 = Null Count. Count has not been transferred from CR to CE and is not yet available for reading. Read/Write Selection Status — RO. These reflect the read/write selection made through bits[5:4] of the control register. The binary codes returned during the status read match the codes used to program the counter read/write selection. 5:4 00 = Counter Latch Command 01 = Read/Write Least Significant Byte (LSB) 10 = Read/Write Most Significant Byte (MSB) 11 = Read/Write LSB then MSB Mode Selection Status — RO. These bits return the counter mode programming. The binary code returned matches the code used to program the counter mode, as listed under the bit function above. 000 = Mode 0 — Out signal on end of count (=0) 3:1 001 = Mode 1 — Hardware retriggerable one-shot x10 = Mode 2 — Rate generator (divide by n counter) x11 = Mode 3 — Square wave output 100 = Mode 4 — Software triggered strobe 101 = Mode 5 — Hardware triggered strobe Countdown Type Status — RO. This bit reflects the current countdown type. 0 0 = Binary countdown 1 = Binary Coded Decimal (BCD) countdown. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 463 LPC Interface Bridge Registers (D31:F0) 13.3.4 Counter Access Ports Register (LPC I/F—D31:F0) I/O Address: Default Value: Bit 7:0 464 Counter 0 – 40h, Counter 1 – 41h, Counter 2 – 42h All bits undefined Attribute: R/W Size: 8 bit Description Counter Port — R/W. Each counter port address is used to program the 16-bit Count Register. The order of programming, either LSB only, MSB only, or LSB then MSB, is defined with the Interval Counter Control Register at port 43h. The counter port is also used to read the current count from the Count Register, and return the status of the counter programming following a Read Back Command. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.4 8259 Interrupt Controller (PIC) Registers (LPC I/F—D31:F0) 13.4.1 Interrupt Controller I/O MAP (LPC I/F—D31:F0) The interrupt controller registers are located at 20h and 21h for the master controller (IRQ 0–7), and at A0h and A1h for the slave controller (IRQ 8–13). These registers have multiple functions, depending upon the data written to them. Table 13-3 shows the different register possibilities for each address. Table 13-3. PIC Registers (LPC I/F—D31:F0) Port Aliases Default Value Type Undefined WO 24h, 28h, Master PIC ICW1 Init. Cmd Word 1 2Ch, 30h, Master PIC OCW2 Op Ctrl Word 2 001XXXXXb WO 34h, 38h, 3Ch Master PIC OCW3 Op Ctrl Word 3 X01XXX10b WO Master PIC ICW2 Init. Cmd Word 2 Undefined WO 2Dh, 31h, Master PIC ICW3 Init. Cmd Word 3 Undefined WO 35h, 39h, 3Dh Master PIC ICW4 Init. Cmd Word 4 01h WO Master PIC OCW1 Op Ctrl Word 1 00h R/W A4h, A8h, Slave PIC ICW1 Init. Cmd Word 1 Undefined WO ACh, B0h, Slave PIC OCW2 Op Ctrl Word 2 001XXXXXb WO Slave PIC OCW3 Op Ctrl Word 3 X01XXX10b WO Slave PIC ICW2 Init. Cmd Word 2 Undefined WO ADh, B1h, Slave PIC ICW3 Init. Cmd Word 3 Undefined WO B5h, B9h, BDh Slave PIC ICW4 Init. Cmd Word 4 01h WO Slave PIC OCW1 Op Ctrl Word 1 00h R/W 4D0h – Master PIC Edge/Level Triggered 00h R/W 4D1h – Slave PIC Edge/Level Triggered 00h R/W 20h 25h, 29h, 21h A0h B4h, B8h, BCh A5h, A9h, A1h Note: Register Name Refer to note addressing active-low interrupt sources in 8259 Interrupt Controllers section (Chapter 5.8). Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 465 LPC Interface Bridge Registers (D31:F0) 13.4.2 ICW1—Initialization Command Word 1 Register (LPC I/F—D31:F0) Offset Address: Master Controller – 20h Slave Controller – A0h Default Value: All bits undefined Attribute: Size: WO 8 bit /controller A write to Initialization Command Word 1 starts the interrupt controller initialization sequence, during which the following occurs: 1. The Interrupt Mask register is cleared. 2. IRQ7 input is assigned priority 7. 3. The slave mode address is set to 7. 4. Special mask mode is cleared and Status Read is set to IRR. Once this write occurs, the controller expects writes to ICW2, ICW3, and ICW4 to complete the initialization sequence. Bit 7:5 ICW/OCW Select — WO. These bits are MCS-85 specific, and not needed. 000 = Should be programmed to “000” 4 ICW/OCW Select — WO. 1 = This bit must be a 1 to select ICW1 and enable the ICW2, ICW3, and ICW4 sequence. 3 Edge/Level Bank Select (LTIM) — WO. Disabled. Replaced by the edge/level triggered control registers (ELCR, D31:F0:4D0h, D31:F0:4D1h). 2 1 0 466 Description ADI — WO. 0 = Ignored for the ICH9. Should be programmed to 0. Single or Cascade (SNGL) — WO. 0 = Must be programmed to a 0 to indicate two controllers operating in cascade mode. ICW4 Write Required (IC4) — WO. 1 = This bit must be programmed to a 1 to indicate that ICW4 needs to be programmed. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.4.3 ICW2—Initialization Command Word 2 Register (LPC I/F—D31:F0) Offset Address: Master Controller – 21h Slave Controller – A1h Default Value: All bits undefined Attribute: Size: WO 8 bit /controller ICW2 is used to initialize the interrupt controller with the five most significant bits of the interrupt vector address. The value programmed for bits[7:3] is used by the processor to define the base address in the interrupt vector table for the interrupt routines associated with each IRQ on the controller. Typical ISA ICW2 values are 08h for the master controller and 70h for the slave controller. Bit 7:3 Description Interrupt Vector Base Address — WO. Bits [7:3] define the base address in the interrupt vector table for the interrupt routines associated with each interrupt request level input. Interrupt Request Level — WO. When writing ICW2, these bits should all be 0. During an interrupt acknowledge cycle, these bits are programmed by the interrupt controller with the interrupt to be serviced. This is combined with bits [7:3] to form the interrupt vector driven onto the data bus during the second INTA# cycle. The code is a three bit binary code: 2:0 Code Master Interrupt Slave Interrupt 000b IRQ0 IRQ8 001b IRQ1 IRQ9 010b IRQ2 IRQ10 011b IRQ3 IRQ11 100b IRQ4 IRQ12 101b IRQ5 IRQ13 110b IRQ6 IRQ14 111b IRQ7 IRQ15 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 467 LPC Interface Bridge Registers (D31:F0) 13.4.4 ICW3—Master Controller Initialization Command Word 3 Register (LPC I/F—D31:F0) Offset Address: 21h Default Value: All bits undefined Bit 7:3 2 1:0 13.4.5 WO 8 bits Description 0 = These bits must be programmed to 0. Cascaded Interrupt Controller IRQ Connection — WO. This bit indicates that the slave controller is cascaded on IRQ2. When IRQ8#–IRQ15 is asserted, it goes through the slave controller’s priority resolver. The slave controller’s INTR output onto IRQ2. IRQ2 then goes through the master controller’s priority solver. If it wins, the INTR signal is asserted to the processor, and the returning interrupt acknowledge returns the interrupt vector for the slave controller. 1 = This bit must always be programmed to a 1. 0 = These bits must be programmed to 0. ICW3—Slave Controller Initialization Command Word 3 Register (LPC I/F—D31:F0) Offset Address: A1h Default Value: All bits undefined Bit 468 Attribute: Size: Attribute: Size: WO 8 bits Description 7:3 0 = These bits must be programmed to 0. 2:0 Slave Identification Code — WO. These bits are compared against the slave identification code broadcast by the master controller from the trailing edge of the first internal INTA# pulse to the trailing edge of the second internal INTA# pulse. These bits must be programmed to 02h to match the code broadcast by the master controller. When 02h is broadcast by the master controller during the INTA# sequence, the slave controller assumes responsibility for broadcasting the interrupt vector. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.4.6 ICW4—Initialization Command Word 4 Register (LPC I/F—D31:F0) Offset Address: Master Controller – 021h Slave Controller – 0A1h Default Value: 01h Bit 7:5 Attribute: Size: WO 8 bits Description 0 = These bits must be programmed to 0. Special Fully Nested Mode (SFNM) — WO. 4 3 2 0 = Should normally be disabled by writing a 0 to this bit. 1 = Special fully nested mode is programmed. Buffered Mode (BUF) — WO. 0 = Must be programmed to 0 for the ICH9. This is non-buffered mode. Master/Slave in Buffered Mode — WO. Not used. 0 = Should always be programmed to 0. Automatic End of Interrupt (AEOI) — WO. 1 0 13.4.7 0 = This bit should normally be programmed to 0. This is the normal end of interrupt. 1 = Automatic End of Interrupt (AEOI) mode is programmed. Microprocessor Mode — WO. 1 = Must be programmed to 1 to indicate that the controller is operating in an Intel Architecture-based system. OCW1—Operational Control Word 1 (Interrupt Mask) Register (LPC I/F—D31:F0) Offset Address: Master Controller – 021h Slave Controller – 0A1h Default Value: 00h Attribute: Size: R/W 8 bits Bit Description 7:0 Interrupt Request Mask — R/W. When a 1 is written to any bit in this register, the corresponding IRQ line is masked. When a 0 is written to any bit in this register, the corresponding IRQ mask bit is cleared, and interrupt requests will again be accepted by the controller. Masking IRQ2 on the master controller will also mask the interrupt requests from the slave controller. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 469 LPC Interface Bridge Registers (D31:F0) 13.4.8 OCW2—Operational Control Word 2 Register (LPC I/F—D31:F0) Offset Address: Master Controller – 020h Attribute: Slave Controller – 0A0h Size: Default Value: Bit[4:0]=undefined, Bit[7:5]=001 WO 8 bits Following a part reset or ICW initialization, the controller enters the fully nested mode of operation. Non-specific EOI without rotation is the default. Both rotation mode and specific EOI mode are disabled following initialization. Bit Description Rotate and EOI Codes (R, SL, EOI) — WO. These three bits control the Rotate and End of Interrupt modes and combinations of the two. 000 = Rotate in Auto EOI Mode (Clear) 001 = Non-specific EOI command 010 = No Operation 7:5 011 = *Specific EOI Command 100 = Rotate in Auto EOI Mode (Set) 101 = Rotate on Non-Specific EOI Command 110 = *Set Priority Command 111 = *Rotate on Specific EOI Command *L0 – L2 Are Used 4:3 OCW2 Select — WO. When selecting OCW2, bits 4:3 = “00” Interrupt Level Select (L2, L1, L0) — WO. L2, L1, and L0 determine the interrupt level acted upon when the SL bit is active. A simple binary code, outlined below, selects the channel for the command to act upon. When the SL bit is inactive, these bits do not have a defined function; programming L2, L1 and L0 to 0 is sufficient in this case. 2:0 470 Code Interrupt Level Code Interrupt Level 000b IRQ0/8 000b IRQ4/12 001b IRQ1/9 001b IRQ5/13 010b IRQ2/10 010b IRQ6/14 011b IRQ3/11 011b IRQ7/15 Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.4.9 OCW3—Operational Control Word 3 Register (LPC I/F—D31:F0) Offset Address: Master Controller – 020h Attribute: Slave Controller – 0A0h Size: Default Value: Bit[6,0]=0, Bit[7,4:2]=undefined, Bit[5,1]=1 Bit WO 8 bits Description 7 Reserved. Must be 0. 6 Special Mask Mode (SMM) — WO. 1 = The Special Mask Mode can be used by an interrupt service routine to dynamically alter the system priority structure while the routine is executing, through selective enabling/disabling of the other channel's mask bits. Bit 5, the ESMM bit, must be set for this bit to have any meaning. Enable Special Mask Mode (ESMM) — WO. 5 4:3 0 = Disable. The SMM bit becomes a “don't care”. 1 = Enable the SMM bit to set or reset the Special Mask Mode. OCW3 Select — WO. When selecting OCW3, bits 4:3 = 01 Poll Mode Command — WO. 2 1:0 0 = Disable. Poll Command is not issued. 1 = Enable. The next I/O read to the interrupt controller is treated as an interrupt acknowledge cycle. An encoded byte is driven onto the data bus, representing the highest priority level requesting service. Register Read Command — WO. These bits provide control for reading the In-Service Register (ISR) and the Interrupt Request Register (IRR). When bit 1=0, bit 0 will not affect the register read selection. When bit 1=1, bit 0 selects the register status returned following an OCW3 read. If bit 0=0, the IRR will be read. If bit 0=1, the ISR will be read. Following ICW initialization, the default OCW3 port address read will be “read IRR”. To retain the current selection (read ISR or read IRR), always write a 0 to bit 1 when programming this register. The selected register can be read repeatedly without reprogramming OCW3. To select a new status register, OCW3 must be reprogrammed prior to attempting the read. 00 = No Action 01 = No Action 10 = Read IRQ Register 11 = Read IS Register Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 471 LPC Interface Bridge Registers (D31:F0) 13.4.10 ELCR1—Master Controller Edge/Level Triggered Register (LPC I/F—D31:F0) Offset Address: 4D0h Default Value: 00h Attribute: Size: R/W 8 bits In edge mode, (bit[x] = 0), the interrupt is recognized by a low to high transition. In level mode (bit[x] = 1), the interrupt is recognized by a high level. The cascade channel, IRQ2, the heart beat timer (IRQ0), and the keyboard controller (IRQ1), cannot be put into level mode. Bit Description IRQ7 ECL — R/W. 7 0 = Edge. 1 = Level. IRQ6 ECL — R/W. 6 0 = Edge. 1 = Level. IRQ5 ECL — R/W. 5 0 = Edge. 1 = Level. IRQ4 ECL — R/W. 4 0 = Edge. 1 = Level. IRQ3 ECL — R/W. 3 2:0 472 0 = Edge. 1 = Level. Reserved. Must be 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.4.11 ELCR2—Slave Controller Edge/Level Triggered Register (LPC I/F—D31:F0) Offset Address: 4D1h Default Value: 00h Attribute: Size: R/W 8 bits In edge mode, (bit[x] = 0), the interrupt is recognized by a low to high transition. In level mode (bit[x] = 1), the interrupt is recognized by a high level. The real time clock, IRQ8#, and the floating point error interrupt, IRQ13, cannot be programmed for level mode. Bit Description IRQ15 ECL — R/W. 7 0 = Edge 1 = Level IRQ14 ECL — R/W. 6 5 0 = Edge 1 = Level Reserved. Must be 0. IRQ12 ECL — R/W. 4 0 = Edge 1 = Level IRQ11 ECL — R/W. 3 0 = Edge 1 = Level IRQ10 ECL — R/W. 2 0 = Edge 1 = Level IRQ9 ECL — R/W. 1 0 = Edge 1 = Level 0 Reserved. Must be 0. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 473 LPC Interface Bridge Registers (D31:F0) 13.5 Advanced Programmable Interrupt Controller (APIC)(D31:F0) 13.5.1 APIC Register Map (LPC I/F—D31:F0) The APIC is accessed via an indirect addressing scheme. Two registers are visible by software for manipulation of most of the APIC registers. These registers are mapped into memory space. The address bits 15:12 of the address range are programmable through bit 7:4 of OIC register (Chipset Configuration Register, offset 31FFh.) The registers are shown in Table 13-4. Table 13-4. APIC Direct Registers (LPC I/F—D31:F0) Address Mnemonic FEC0_0000h IND FEC0_0010h FECO_0040h Register Name Size Type Index 8 bits R/W DAT Data 32 bits R/W EOIR EOI 32 bits WO Table 13-5 lists the registers which can be accessed within the APIC via the Index Register. When accessing these registers, accesses must be done one dword at a time. For example, software should never access byte 2 from the Data register before accessing bytes 0 and 1. The hardware will not attempt to recover from a bad programming model in this case. Table 13-5. APIC Indirect Registers (LPC I/F—D31:F0) Index 13.5.2 Mnemonic 00 ID 01 VER 02–0F — 10–11 REDIR_TBL0 12–13 REDIR_TBL1 ... ... 3E–3F REDIR_TBL23 40–FF — Register Name Size Type Identification 32 bits R/W Version 32 bits RO — RO Redirection Table 0 64 bits R/W, RO Redirection Table 1 64 bits R/W, RO ... ... 64 bits R/W, RO — RO Reserved ... Redirection Table 23 Reserved IND—Index Register (LPC I/F—D31:F0) Memory Address Default Value: FEC0_0000h 00h Attribute: Size: R/W 8 bits The Index Register will select which APIC indirect register to be manipulated by software. The selector values for the indirect registers are listed in Table 13-5. Software will program this register to select the desired APIC internal register . Bit 7:0 474 Description APIC Index — R/W. This is an 8-bit pointer into the I/O APIC register table. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.5.3 DAT—Data Register (LPC I/F—D31:F0) Memory Address Default Value: FEC0_0010h 00000000h Attribute: Size: R/W 32 bits This is a 32-bit register specifying the data to be read or written to the register pointed to by the Index register. This register can only be accessed in dword quantities. Bit 7:0 13.5.4 Description APIC Data — R/W. This is a 32-bit register for the data to be read or written to the APIC indirect register (Figure 13-5) pointed to by the Index register (Memory Address FEC0_0000h). EOIR—EOI Register (LPC I/F—D31:F0) Memory Address Default Value: FEC0h_0040h N/A Attribute: Size: WO 32 bits The EOI register is present to provide a mechanism to maintain the level triggered semantics for level-triggered interrupts issued on the parallel bus. When a write is issued to this register, the I/O APIC will check the lower 8 bits written to this register, and compare it with the vector field for each entry in the I/O Redirection Table. When a match is found, the Remote_IRR bit (Index Offset 10h, bit 14) for that I/O Redirection Entry will be cleared. Note: If multiple I/O Redirection entries, for any reason, assign the same vector for more than one interrupt input, each of those entries will have the Remote_IRR bit reset to 0. The interrupt which was prematurely reset will not be lost because if its input remained active when the Remote_IRR bit is cleared, the interrupt will be reissued and serviced at a later time. Note: Only bits 7:0 are actually used. Bits 31:8 are ignored by the ICH9. Note: To provide for future expansion, the processor should always write a value of 0 to Bits 31:8. Bit Description 31:8 Reserved. To provide for future expansion, the processor should always write a value of 0 to Bits 31:8. 7:0 Redirection Entry Clear — WO. When a write is issued to this register, the I/O APIC will check this field, and compare it with the vector field for each entry in the I/O Redirection Table. When a match is found, the Remote_IRR bit for that I/O Redirection Entry will be cleared. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 475 LPC Interface Bridge Registers (D31:F0) 13.5.5 ID—Identification Register (LPC I/F—D31:F0) Index Offset: Default Value: 00h 00000000h Attribute: Size: R/W 32 bits The APIC ID serves as a physical name of the APIC. The APIC bus arbitration ID for the APIC is derived from its I/O APIC ID. This register is reset to 0 on power-up reset. Bit 31:28 Reserved 27:24 APIC ID — R/W. Software must program this value before using the APIC. 23:16 Reserved 15 14:0 13.5.6 Description Scratchpad Bit. Reserved VER—Version Register (LPC I/F—D31:F0) Index Offset: Default Value: 01h 00170020h Attribute: Size: RO, RWO 32 bits Each I/O APIC contains a hardwired Version Register that identifies different implementation of APIC and their versions. The maximum redirection entry information also is in this register, to let software know how many interrupt are supported by this APIC. Bit Description 31:24 Reserved 23:16 Maximum Redirection Entries (MRE) — RWO. This is the entry number (0 being the lowest entry) of the highest entry in the redirection table. It is equal to the number of interrupt input pins minus one and is in the range 0 through 239. In the ICH9 this field is hardwired to 17h to indicate 24 interrupts. BIOS must write to this field after PLTRST# to lockdown the value. this allows BIOS to utilize some of the entries for its own purpose and thus advertising fewer IOxAPIC Redirection Entries to the OS. 15 14:8 7:0 476 Pin Assertion Register Supported (PRQ) — RO. Indicate that the IOxAPIC does not implement the Pin Assertion Register. Reserved Version (VS) — RO. This is a version number that identifies the implementation version. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet LPC Interface Bridge Registers (D31:F0) 13.5.7 REDIR_TBL—Redirection Table (LPC I/F—D31:F0) Index Offset: Default Value: 10h–11h (vector 0) through 3E–3Fh (vector 23) Bit 16 = 1. All other bits undefined Attribute:R/W, RO Size: 64 bits each, (accessed as two 32 bit quantities) The Redirection Table has a dedicated entry for each interrupt input pin. The information in the Redirection Table is used to translate the interrupt manifestation on the corresponding interrupt pin into an APIC message. The APIC will respond to an edge triggered interrupt as long as the interrupt is held until after the acknowledge cycle has begun. Once the interrupt is detected, a delivery status bit internally to the I/O APIC is set. The state machine will step ahead and wait for an acknowledgment from the APIC unit that the interrupt message was sent. Only then will the I/O APIC be able to recognize a new edge on that interrupt pin. That new edge will only result in a new invocation of the handler if its acceptance by the destination APIC causes the Interrupt Request Register bit to go from 0 to 1. (In other words, if the interrupt was not already pending at the destination.) Bit Description 63:56 Destination — R/W. If bit 11 of this entry is 0 (Physical), then bits 59:56 specifies an APIC ID. In this case, bits 63:59 should be programmed by software to 0. If bit 11 of this entry is 1 (Logical), then bits 63:56 specify the logical destination address of a set of processors. 55:48 Extended Destination ID (EDID) — RO. These bits are sent to a local APIC only when in Processor System Bus mode. They become bits 11:4 of the address. 47:17 Reserved Mask — R/W. 16 15 14 13 12 0 = Not masked: An edge or level on this interrupt pin results in the delivery of the interrupt to the destination. 1 = Masked: Interrupts are not delivered nor held pending. Setting this bit after the interrupt is accepted by a local APIC has no effect on that interrupt. This behavior is identical to the device withdrawing the interrupt before it is posted to the processor. It is software's responsibility to deal with the case where the mask bit is set after the interrupt message has been accepted by a local APIC unit but before the interrupt is dispensed to the processor. Trigger Mode — R/W. This field indicates the type of signal on the interrupt pin that triggers an interrupt. 0 = Edge triggered. 1 = Level triggered. Remote IRR — R/W. This bit is used for level triggered interrupts; its meaning is undefined for edge triggered interrupts. 0 = Reset when an EOI message is received from a local APIC. 1 = Set when Local APIC/s accept the level interrupt sent by the I/O APIC. Interrupt Input Pin Polarity — R/W. This bit specifies the polarity of each interrupt signal connected to the interrupt pins. 0 = Active high. 1 = Active low. Delivery Status — RO. This field contains the current status of the delivery of this interrupt. Writes to this bit have no effect. 0 = Idle. No activity for this interrupt. 1 = Pending. Interrupt has been injected, but delivery is not complete. Intel® I/O Controller Hub 9 (ICH9) Family Datasheet 477 LPC Interface Bridge Registers (D31:F0) Bit Description Destination Mode — R/W. This field determines the interpretation of the Destination field. 11 0 = Physical. Destination APIC ID is identified by bits 59:56. 1 = Logical. Destinations are identified by matching bit 63:56 with the Logical Destination in the Destination Format Register and Logical Destination Register in each Local APIC. 10:8 Delivery Mode — R/W. This field specifies how the APICs listed in the destination field should act upon reception of this signal. Certain Delivery Modes will only operate as intended when used in conjunction with a specific trigger mode. These encodings are listed in the note below: 7:0 Vector — R/W. This field contains the interrupt vector for this interrupt. Values range between 10h and FEh. NOTE: Delivery Mode encoding: 478 000 = Fixed. Deliver the signal on the INTR signal of all processor cores listed in the destination. Trigger Mode can be edge or level. 001 = Lowest Priority. Deliver the signal on the INTR signal of the processor core that is executing at the lowest priority among all the processors listed in the specified destination. Trigger Mode can be edge or level. 010 = SMI (System Management Interrupt). Requires the interrupt to be programmed as edge triggered. The vector information is ignored but must be programmed to all 0s for future compatibility: not supported 011 = Reserved 100 = NMI. Deliver the signal on the NMI signal of all processor cores listed in the destination. Vector information is ignored. NMI is treated as an edge triggered interrupt even if it is programmed as level triggered. For proper operation this redirection table entry must be programmed to edge triggered. The NMI delivery mode does not set the RIRR bit. If the redirection table is incorrectly set to level, the loop count will continue counting through the redirection table addresses. Once the count for the NMI pin is reached again, the interrupt will be sent again: not supported 101 = INIT. Deliver the signal to all processor cores listed in the destination by asserting the INIT signal. All addressed local APICs will assume their INIT state. INIT is always treated as an edge triggered interrupt even if programmed as level triggered. For proper operation this redirection table entry must be programmed to edge triggered. The INIT delivery mode does not set the RIRR bit. If the redirection table is incorrectly set to level, the loop count will continue counting through the redirection table addresses. Once the count for the INIT pin is reached again, the interrupt will be sent again: not supported 110 = Reserved 111 = ExtINT. Deliver the signal to the INTR signal of all processor cores listed in the destination as an interrupt that originated in an externally connected 8259A compatible interrupt controller. The INTA cycle that corresponds to