LX7202-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET KEY FEATURES DESCRIPTION Bi-directional EMI/RFI low-pass filter Line termination with integrated ESD protection Low TVS operating voltage (5.25V) Low leakage current Integrated single die construction Available with 15 or 22Ω Series Resistance Crosses from Semtech STF202 The 47 pF capacitor completes the high frequency filter and controls the edge rate of the USB signals. The LX7202 protects both D+ and D- data lines and the voltage bus from ESD. The TVS protection diodes exceed the requirements of IEC61000-4-2, level 4, 15kV (air discharge) and 8kV (contact discharge).The integrated configuration of the LX7202 minimizes board space and allows for ideal placement near the connector. The LX7202 is ideal for use in USB hubs, peripherals and portable appliances. APPLICATIONS USB 1.1 and USB 2.0 Full Speed Compliant Peripherals Computers and Printers Mobile phones Pagers and PDA’s Digital Cameras IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com PACKAGE ORDER INFO TJ (°C) Plastic 6-Pin SOT23 LX7202-15ISF LX7202-22ISF SF -40 to 125 -40 to 125 Package Marking 215 222 WWW . Microsemi .C OM The LX7202 is an integrated Universal Serial Bus (USB) line termination device with an EMI filter and ESD protection diodes. This device offers a cost effective and compact solution for one USB upstream port. The USB specification requires line termination resistors on both the D+ and D- lines. These resistors ensure signal integrity by matching the cable impedance to that of the differential driver. The 1.5 kΩ pull-up resistor identifies the appropriate data line for full speed or low speed operation. Tape & Reel Quantity (Reel Size) BENEFITS 3K (7inches) Filter response characterized up to 6 GHz <2dB insertion loss in the pass band >20dB attenuation in the 800900 MHz range >12dB attenuation in the WLAN frequencies of 2.4GHz and 5.06.0 GHz Note: Append the letter “T” to the part number For Tape & Reel Ordering PRODUCT HIGHLIGHT Rs D in from connector D out to IC 47pF 1.5K DIN 6 1 from connector 47pF D in from connector Rs D out to IC Circuit Diagram Copyright © 2002 Rev. 1.0c, 2005-01-28 DIN from connector 1 2 RPU 6 GND 5 DOUT 4 DOUT C RS LX7202-XX VBUS VBUS to IC C 3 to IC RS Functional Schematic with PinOut Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LX7202-xx I N T E G R A T E D P R O D U C T S EMI Filter & ESD Protection for Up Stream USB Ports P RODUCTION D ATA S HEET ABSOLUTE MAXIMUM RATINGS Steady State Power ...........................................................................100mW ESD Air Discharge per IEC61000-4-2.................................................16KV ESD Contact Discharge per IEC61000-4-2 .........................................10KV Lead Soldering Temperature (10 Seconds) ........................................ 260°C Operating Temperature ...................................................... -40°C to +125°C Storage Temperature Range............................................... -55°C to +150°C VBUS 1 6 GND DIN 2 5 DOUT DIN 3 from connector from connector WWW . Microsemi .C OM PACKAGE PIN OUT to IC 4 DOUT to IC Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. SF PACKAGE (Top View) THERMAL DATA SF Plastic SOT-23 6-Pin THERMAL RESISTANCE-JUNCTION TO CASE, θJC THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA 62 °C/W 96 °C/W Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. FUNCTIONAL PIN DESCRIPTION Name VBUS Description Bus Voltage DIN Data In GND Ground DOUT Data Out ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the operating ambient temperature -40°C ≤ TA otherwise noted. Symbol Stand-Off Voltage Breakdown Voltage Leakage Current Series Resistance (-15) Series Resistance (-22) Temperature Coefficient of RS Pull Up Resistance Capacitor VRWM VBR IR RS RS TCOEFF RPU C Total Capacitance Copyright © 2002 Rev. 1.0c, 2005-01-28 CTOT Test Conditions IR = 1mA VRWM = 5.25V, T = 25°C Each Line Each Line Each Line Each Line Each Line Between I/O Pins and Ground, Each Device VR = 0V, f = 1MHz Min +125°C except where LX7202-xx Typ Max 5.25 6 13.5 19.8 1.35 54 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 15 22 200 1.5 47 60 1 16.5 24.2 1.65 66 Units V V µA Ω Ω ppm KΩ pF pF Page 2 ELECTRICALS Parameter ≤ LX7202-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET APPLICATION CIRCUITS Peripheral (upstream) port LX7201 LX7202 V BUS RS 4 WWW . Microsemi .C OM Host or Hub (downstream) port GND 1 3 RPU C 6 C USB Transceiver RPD 5 RS 2 RS 2 USB Transceiver 5 C C RPD 6 1 GND V BUS 3 4 RS Figure 1 – Typical Application APPLICATION INFORMATION The LX7202 meets the requirements of the USB v1.1 and USB 2.0 Full Speed specification for device termination, EMI filtering and ESD protection. The RS resistor provides the proper signal termination; the 47pF capacitor controls the signal rise and fall slew; the TVS diodes protect the IC from ESD damage; and the total capacitance and resistance creates a low pass filter eliminating the high frequency energy from the circuit. The LX7202 can configure the upstream port for either Full-Speed or Low-Speed operation. The figures below show the proper connection in accordance with the USB specification. Host USB Transceiver cable Voltage Supply (Vbus) is connected to Pin 1 Ground is connected to Pin 6 D+ from the connector is routed to Pin 3 (1.5 kΩ pull-up resistor) and Pin 4 to the D+ line of the USB Transceiver D- from the connector is routed to Pin 2 and Pin 5 to the D- line of the USB Transceiver 1 6 VBUS GND LX7202 2 5 DIN GND VBUS DD+ Peripheral USB Transceiver APPLICATIONS GND VBUS DD+ FULL SPEED DEVICE The USB 2.0 specification offers a 12 Mbps data transfer rate known as Full-Speed which requires a 1.5 kΩ pull-up resistor to be connected to the D+ line. Slew rate control is accomplished with 47pF attached to the transceiver before the RS. DOUT 3 RPU DIN 4 DOUT Figure 2 – Connection for Full Speed Operation Copyright © 2002 Rev. 1.0c, 2005-01-28 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 LX7202-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET Voltage Supply (Vbus) is connected to Pin 1 Ground is connected to Pin 6 D+ from the connector is routed to Pin 2 and Pin 5 to the D+ line of the USB Transceiver D- from the connector is routed to Pin 3 (1.5 kΩ pullup resistor) and Pin 4 to the D- line of the USB Transceiver LOW SPEED DEVICE The USB v1.1 specification offers a 1.5 Mbps data transfer rate known as Low-Speed which requires a 1.5 k Ω pull-up resistor to be connected to the D- line. Slew rate control is accomplished with 47pF attached to the transceiver before the RS. Host USB Transceiver cable GND VBUS DD+ 1 6 VBUS GND LX7202 2 5 DIN GND VBUS DD+ Peripheral USB Transceiver DOUT 3 DIN WWW . Microsemi .C OM APPLICATION INFORMATION (CONTINUED) R PU 4 DOUT Figure 3 – Connection for Low Speed Operation ELECTROMAGNETIC EMISSION AND SUSCEPTABILITY Copyright © 2002 Rev. 1.0c, 2005-01-28 control cards, interface boards, external memory expansion cards and other input/output devices that may or may not contain digital circuitry. LX7202 is optimized to minimize the radiated EMI which is the primary concern in devices using USB. Refer to the typical filter response curve for the attenuation characteristics of LX7202 over the frequency range of 30KHz to 6GHz. Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 APPLICATIONS FCC Part 15 sets limits for maximum allowable EM emission and susceptibility. There are two types of emissions. Conducted emissions with frequency of emission of 0.45 to 30 MHz and Radiated emissions with frequency of emission of 30 MHz to 40 GHz. All digital computing devices including the peripheral devices must comply. Examples of peripheral devices include terminals, printers, external floppy disk drives and other fixed adjustable data storage devices, video monitors, keyboards, LX7202-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET WWW . Microsemi .C OM CHARACTERISTIC CURVES 8KV Contact ESD 1 M 5.0VΩ Ch1 40.0ns Figure 4 – 8KV ESD input pulse as per IEC61000-4-2. Vertical scale is equivalent to 5A/div. CH1 S12 LOG 5dB / REF 0 dB Figure 6 – Frequency response curve. Low insertion loss in the pass band and -20dB attenuation at 800-900 MHz. Better than -10dB attenuation at the WLAN frequencies of 2.4 and 5.0-6.0 GHz. Copyright © 2002 Rev. 1.0c, 2005-01-28 40.0ns Figure 5 – Clamping Characteristics when device subjected to an 8 KV ESD pulse. CH1 S12 LOG STOP 6 000.000 000 MHz M 20dB / REF 0 dB START 0.030 000 MHz STOP 6 000.000 000 MHz Figure 7 – Analog Crosstalk between the two datalines Dand D+ Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 CHARTS START 0.030 000 MHz 5.0V Ω LX7202-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET PACKAGE DIMENSIONS WWW . Microsemi .C OM SF 6 Pin Plastic SOT-23 D Dim A A1 B C D E F G H I J K G H E A1 A C B F J K I MILLIMETERS MIN MAX 0.90 1.30 0.90 1.45 0.25 0.50 0.09 0.20 2.80 3.10 1.50 1.75 0.95 BSC 1.90 BSC 2.60 3.00 0.35 0.55 0.00 0.15 10° MAX INCHES MIN MAX 0.035 0.051 0.035 0.057 0.010 0.020 0.004 0.008 0.110 0.122 0.059 0.069 0.038 BSC 0.075 BSC 0.102 0.118 0.014 0.022 0.000 0.006 10° MAX Note: 1. Dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006”) on any side. Lead dimension shall not include solder coverage. Recommended Footprint X Dim C D E X Y Y C (ref) MILLIMETERS MIN MAX 2.40 1.90 0.95 0.70 1.00 INCHES MIN MAX 0.094 0.074 0.037 0.028 0.039 MECHANICALS E (ref) D (ref) Copyright © 2002 Rev. 1.0c, 2005-01-28 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 LX7202-xx I N T E G R A T E D P R O D U C T S EMI Filter & ESD Protection for Up Stream USB Ports P RODUCTION D ATA S HEET NOTES WWW . Microsemi .C OM NOTES PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2002 Rev. 1.0c, 2005-01-28 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7