TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 N-CHANNEL MOSFET Qualified per MIL-PRF-19500/556 DEVICES LEVELS 2N6784 2N6784U JAN JANTX JANTXV ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Drain – Source Voltage VDS 200 Vdc Gate – Source Voltage Continuous Drain Current VGS ± 20 Vdc ID1 2.25 Adc ID2 1.5 Adc Ptl 15 (1) W (2) Ω TC = +25°C Continuous Drain Current TC = +100°C Max. Power Dissipation Drain to Source On State Resistance Operating & Storage Temperature Rds(on) Top, Tstg 1.5 -55 to +150 °C Note: (1) Derated Linearly by 0.12 W/°C for TC > +25°C (2) VGS = 10Vdc, ID = 1.5A TO-205AF (formerly TO-39) ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) Parameters / Test Conditions Drain-Source Breakdown Voltage VGS = 0V, ID = 1mAdc Symbol Min. V(BR)DSS 200 Gate-Source Voltage (Threshold) VDS ≥ VGS, ID = 0.25mA VDS ≥ VGS, ID = 0.25mA, Tj = +125°C VDS ≥ VGS, ID = 0.25mA, Tj = -55°C VGS(th)1 VGS(th)2 VGS(th)3 2.0 1.0 Gate Current VGS = ±20V, VDS = 0V VGS = ±20V, VDS = 0V, Tj = +125°C IGSS1 IGSS2 Drain Current VGS = 0V, VDS = 160V VGS = 0V, VDS = 160V, Tj = +125°C Static Drain-Source On-State Resistance VGS = 10V, ID = 1.5A pulsed VGS = 10V, ID = 2.25A pulsed Tj = +125°C VGS = 10V, ID = 1.5A pulsed Diode Forward Voltage VGS = 0V, ID = 2.25A pulsed T4-LDS-0176 Rev. 1 (101183) Max. Unit Vdc 4.0 Vdc 5.0 ±100 ±200 nAdc U – 18 LCC IDSS1 IDSS2 25 0.25 µAdc mAdc rDS(on)1 rDS(on)2 1.5 1.6 Ω Ω rDS(on)3 2.81 Ω VSD 1.5 Vdc Page 1 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 DYNAMIC CHARACTERISTICS Parameters / Test Conditions Gate Charge: On-State Gate Charge Gate to Source Charge Gate to Drain Charge Symbol VGS = 10V, ID = 2.25A VDS = 100V Min. Qg(on) Qgs Qgd Max. Unit 8.6 1.5 5.5 nC Max. Unit SWITCHING CHARACTERISTICS Parameters / Test Conditions Symbol Switching time tests: Turn-on delay time Rinse time Turn-off delay time Fall time ID = 2.25A, VGS = 10Vdc, Gate drive impedance = 7.5Ω, VDD = 100Vdc Diode Reverse Recovery Time di/dt ≤ 100A/µs, VDD ≤ 50V, IF = 2.25A T4-LDS-0176 Rev. 1 (101183) Min. td(on) tr td(off) tf 15 20 30 20 trr 350 ns ns Page 2 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Ltr CD CH HD h J k LD LL LS LU L1 L2 P Q r α Dimensions Inches Millimeters Min Max Min Max .305 .355 7.75 9.02 .160 .180 4.07 4.57 .335 .370 8.51 9.39 .009 .041 0.23 1.04 .028 .034 0.72 0.86 .029 .045 0.74 1.14 .016 .021 0.41 0.53 .500 .750 12.7 19.05 .200 TP 5.08 TP .016 .019 0.41 0.48 .050 1.27 .250 6.35 .070 1.78 .050 1.27 .010 0.25 45° TP 45° TP Notes 2 3 7, 8 7, 8 6 7, 8 7, 8 7, 8 5 4 9 6 NOTES: 1 2 3 4 5 6 Dimensions are in inches. Millimeters are given for general information only. Beyond radius (r) maximum, j shall be held for a minimum length of .011 (0.028 mm). Dimension k measured from maximum HD. Outline in this zone is not controlled. Dimension CD shall not vary more than .010 (0.25 mm) in zone P. This zone is controlled for automatic handling. Leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7 LU applies between L1 and L2. LD applies between L2 and L minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8 All three leads. 9 Radius (r) applies to both inside corners of tab. 10 Drain is electrically connected to the case. 11 In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. FIGURE 1. Physical dimensions for TO-205AF. T4-LDS-0176 Rev. 1 (101183) Page 3 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 NOTES: Dimensions Inches Millimeters Min Max Min Max .345 .360 8.77 .280 .295 7.11 .095 .115 2.41 .040 .055 1.02 .055 .065 1.40 .050 BSC 1.27 BSC .025 BSC 0.635 BSC .008 BSC 0.203 BSC .020 .030 0.51 0.76 .105 REF 2.67 REF .120 REF 3.05 REF .045 .055 1.14 1.40 .070 .080 1.78 2.03 .120 .130 3.05 3.30 1 2 3 4 Dimensions are in inches. Millimeters are given for general information only. In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. Ceramic package only. Ltr BL BW CH LL1 LL2 LS LS1 LS2 LW Q1 Q2 Q3 TL TW FIGURE 2. Physical dimensions for LCC. T4-LDS-0176 Rev. 1 (101183) Page 4 of 4