LINER LT1369CS

LT1366/LT1367
LT1368/LT1369
Dual and Quad Precision
Rail-to-Rail Input and Output
Op Amps
Description
Features
Input Common Mode Range Includes Both Rails
Output Swings Rail-to-Rail
Low Input Offset Voltage: 150µV
High Common Mode Rejection Ratio: 90dB
High AVOL: >1V/µV Driving 10k Load
Low Input Bias Current: 10nA
Wide Supply Range: 1.8V to ±15V
Low Supply Current: 375µA per Amplifier
High Output Drive: 30mA
400kHz Gain-Bandwidth Product
Slew Rate: 0.13V/µs
Stable for Capacitive Loads Up to 1000pF
The LT®1366/LT1367/LT1368/LT1369 are dual and quad
bipolar op amps which combine rail-to-rail input and output
operation with precision specifications. These op amps
maintain their characteristics over a supply range of 1.8V
to 36V. Operation is specified for 3V, 5V and ±15V supplies.
Input offset voltage is typically 150µV, with an open-loop
gain AVOL of 1 million while driving a 10k load. Common
mode rejection is typically 90dB over the full rail-to-rail
input range, and supply rejection is 110dB.
The LT1366/LT1367 have conventional compensation
which assures stability for capacitive loads of 1000pF or
less. The LT1368/LT1369 have compensation that requires
a 0.1µF output capacitor, which improves the amplifier’s
supply rejection and reduces output impedance at high
frequencies. The output capacitor’s filtering action reduces
high frequency noise, which is beneficial when driving
A/D converters.
Applications
n
n
n
n
Rail-to-Rail Buffer Amplifiers
Low Voltage Signal Processing
Supply Current Sensing at Either Rail
Driving A/D Converters
The LT1366/LT1368 are available in plastic 8-pin PDIP
and 8-lead SO packages with the standard dual op amp
pinout. The LT1367/LT1369 feature the standard quad
pinout, which is available in a plastic 14-lead SO package.
These devices can be used as plug-in replacements for
many standard op amps to improve input/output range
and precision.
L, LT, LTC, LTM, Over-The-Top, Linear Technology and the Linear logo are registered
trademarks and C-Load is a trademark of Linear Technology Corporation. All other trademarks
are the property of their respective owners.
Typical Application
Output Saturation Voltage vs Load Current
Positive Supply Rail Current Sense
VCC
1000
R1
200Ω
SATURATION VOLTAGE (mV)
|VOUT – VS|
n
n
n
n
n
n
n
n
n
n
n
n
100
Rs
0.2Ω
–
–
Q1
TP0610L
1/2 LT1366
+
ILOAD
LOAD
R2
20k
1/2 LT1366
+
( )
R2
R1
= ILOAD • 20Ω
VO = ILOAD • RS
1366 TA01
POSITIVE
RAIL
NEGATIVE
RAIL
10
1
0.001
0.01
0.1
1
LOAD CURRENT (mA)
10
1366 TA02
1366fb
LT1366/LT1367
LT1368/LT1369
Absolute Maximum Ratings
(Note 1)
Total Supply Voltage (V+ to V–)................................. 36V
Input Current........................................................ ±15mA
Output Short-Circuit Duration (Note 2)......... Continuous
Operating Temperature Range ............... –40°C to 85°C
Specified Temperature Range....................... 0°C to 70°C
Junction Temperature .......................................... 150°C
Storage Temperature Range.................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
Pin Configuration
LT1366/LT1368
LT1367/LT1369
TOP VIEW
TOP VIEW
–IN A 2
+IN A 3
V– 4
–IN A 2
7 OUT B
A
B
14 OUT D
OUT A 1
8 V+
OUT A 1
+IN A 3
6 –IN B
A
D
V+ 4
5 +IN B
+IN B 5
N8 PACKAGE
8-LEAD PDIP
–IN B 6
12 +IN D
11 V–
B
C
10 +IN C
9 – IN C
8 OUT C
OUT B 7
S8 PACKAGE
8-LEAD PLASTIC SO
13 –IN D
S PACKAGE
14-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 130°C/W (N8)
TJMAX = 150°C, θJA = 190°C/W (S8)
TJMAX = 150°C, θJA = 150°C/W
AVAILABLE OPTIONS
PRODUCT NUMBER
LT1366
LT1367
LT1368
LT1369
NUMBER OF OP AMPS
2
4
2
4
LOAD CAPACITANCE
0pF < CL < 1000pF
0pF < CL < 1000pF
CL = 0.1µF
CL = 0.1µF
MAX VOS (25°C)
AT VS = 5V, 0V
475µV
800µV
475µV
800µV
ORDER PART NUMBER
PLASTIC (N)
LT1366CN8
LT1368CN8
SURFACE MOUNT(S)
LT1366CS8
LT1367CS
LT1368CS8
LT1369CS
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT1366CN8#PBF
LT1366CN8#TRPBF
1366
8-Lead PDIP
0°C to 70°C
LT1366CS8#PBF
LT1366CS8#TRPBF
1366
8-Lead Plastic S0
0°C to 70°C
LT1367CS#PBF
LT1367CS#TRPBF
LT1367CS
14-Lead Plastic S0
0°C to 70°C
LT1368CN8#PBF
LT1368CN8#TRPBF
1368
8-Lead PDIP
0°C to 70°C
LT1368CS8#PBF
LT1368CS8#TRPBF
1368
8-Lead Plastic S0
0°C to 70°C
LT1369CS#PBF
LT1369CS#TRPBF
LT1369CS
14-Lead Plastic S0
0°C to 70°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1366fb
LT1366/LT1367
LT1368/LT1369
Electrical
Characteristics
TA = 25°C; VS = 5V, 0V; VCM = 2.5V; VO = 2.5V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage (LT1366/LT1368)
∆VOS
IB
MIN
TYP
MAX
UNITS
VCM = VCC
VCM = VEE
150
150
475
475
µV
µV
Input Offset Voltage (LT1367/LT1369)
VCM = VCC
VCM = VEE
150
150
800
700
µV
µV
Input Offset Voltage Shift (LT1366/LT1368)
Input Offset Voltage Match (Channel to Channel)
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
150
250
400
700
µV
µV
Input Offset Voltage Shift (LT1367/LT1369)
Input Offset Voltage Match (Channel to Channel)
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
150
250
650
1600
µV
µV
Input Bias Current
VCM = VCC
VCM = VEE
10
–10
35
0
nA
nA
0
–35
∆IB
Input Bias Current Shift
VCM = VEE to VCC
20
70
nA
IOS
Input Offset Current
VCM = VCC
VCM = VEE
1
0.3
12
12
nA
nA
∆IOS
Input Offset Current Shift
VCM = VEE to VCC
1
12
nA
Input Bias Current Match (Channel to Channel)
VCM = VCC (Note 4)
VCM = VEE (Note 4)
1
1
12
12
nA
nA
Input Noise Voltage Density
f = 1kHz
29
nV/√Hz
in
Input Noise Current Density
f = 1kHz
0.07
pA/√Hz
CIN
Input Capacitance
AVOL
Large-Signal Voltage Gain
CMRR
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
en
0
0
12
VO = 50mV to 4.8V, RL = 10k
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel to Channel) (Note 4)
VS = 2.0V to 12V, VCM = VO = 0.5V
VS = 2.0V to 12V, VCM = VO = 0.5V
VOL
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 2.5mA
VOH
Output Voltage Swing High
No Load
ISINK = 0.5mA
ISINK = 2.5mA
ISC
Short-Circuit Current
(Note 2)
IS
Supply Current per Amplifier
GBW
Gain-Bandwidth Product (LT1366/LT1367)
Gain-Bandwidth Product (LT1368/LT1369)
AV = 1000
AV = 1000
tS
Settling Time (LT1366/LT1367)
AV = 1, VSTEP = 4V to 0.1%
pF
250
2000
81
75
90
90
dB
dB
77
71
90
90
dB
dB
90
84
105
100
dB
dB
6
40
110
V/mV
12
70
200
VCC – 0.012 VCC – 0.004
VCC – 0.100 VCC – 0.050
VCC – 0.250 VCC – 0.150
±15
V
V
V
±30
340
0.4
0.16
30
mV
mV
mV
mA
520
µA
MHz
MHz
µs
1366fb
LT1366/LT1367
LT1368/LT1369
Electrical
Characteristics
The l denotes the specifications which apply over the specified
temperature range of 0°C < TA < 70°C. VS = 5V, 0V; VCM = 2.5V, VO = 2.5V, unless otherwise noted.
SYMBOL
VOS
VOS TC
∆VOS
IB
∆IB
IOS
∆IOS
AVOL
CMRR
PSRR
VOL
VOH
ISC
IS
PARAMETER
Input Offset Voltage (LT1366/LT1368)
CONDITIONS
VCM = VCC
VCM = VEE
Input Offset Voltage (LT1367/LT1369)
VCM = VCC
VCM = VEE
Input Offset Voltage Drift
(Note 3)
Input Offset Voltage Shift (LT1366/LT1368)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Offset Voltage Shift (LT1367/LT1369)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Bias Current
VCM = VCC
VCM = VEE
Input Bias Current Shift
VCM = VEE to VCC
Input Offset Current
VCM = VCC
VCM = VEE
Input Offset Current Shift
VCM = VEE to VCC
Input Bias Current Match (Channel to Channel)
VCM = VCC (Note 4)
VCM = VEE (Note 4)
Large-Signal Voltage Gain
VO = 50mV to 4.8V, RL = 10k
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Power Supply Rejection Ratio
VS = 2.3V to 12V, VCM = VO = 0.5V
VS = 2.3V to 12V, VCM = VO = 0.5V
PSRR Match (Channel to Channel) (Note 4)
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 2.5mA
Output Voltage Swing High
No Load
ISOURCE = 0.5mA
ISOURCE = 2.5mA
Short-Circuit Current
(Note 2)
Supply Current per Amplifier
MIN
l
l
l
l
l
l
l
l
l
l
l
0
–45
l
TYP
200
200
200
200
2
200
250
200
250
15
–10
25
MAX
575
575
950
900
6
425
900
675
1900
45
0
90
UNITS
µV
µV
µV
µV
µV/°C
µV
µV
µV
µV
nA
nA
nA
15
15
15
15
15
540
nA
nA
nA
nA
nA
V/mV
dB
dB
dB
dB
dB
dB
mV
mV
mV
V
V
V
mA
µA
TYP
150
150
150
150
150
250
150
250
10
–10
20
MAX
475
475
850
750
400
700
650
1700
35
0
70
UNITS
µV
µV
µV
µV
µV
µV
µV
µV
nA
nA
nA
1.0
0.3
12
12
2
1
l
2
l
0
2
l
0
1
l
250
2000
l
80
87
l
74
87
l
77
87
l
71
87
l
88
105
l
82
100
l
9
l
45
l
120
l VCC – 0.014 VCC – 0.005
l VCC – 0.110 VCC – 0.055
l VCC – 0.300 VCC – 0.180
l
±12.5
l
385
l
l
14
80
230
TA = 25°C; VS = 3V, 0V; VCM = 1.5V; VO = 1.5V, unless otherwise noted.
SYMBOL
VOS
PARAMETER
Input Offset Voltage (LT1366/LT1368)
Input Offset Voltage (LT1367/LT1369)
IB
Input Offset Voltage Shift (LT1366/LT1368)
Input Offset Voltage Match (Channel to Channel)
Input Offset Voltage Shift (LT1367/LT1369)
Input Offset Voltage Match (Channel to Channel)
Input Bias Current
∆IB
IOS
Input Offset Current
∆VOS
Input Bias Current Shift
CONDITIONS
VCM = VCC
VCM = VEE
VCM = VCC
VCM = VEE
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
VCM = VCC
VCM = VEE
VCM = VEE to VCC
VCM = VCC
VCM = VEE
MIN
0
–35
nA
nA
1366fb
LT1366/LT1367
LT1368/LT1369
Electrical
Characteristics
SYMBOL
∆IOS
AVOL
CMRR
VOL
VOH
ISC
IS
TA = 25°C; VS = 3V, 0V; VCM = 1.5V; VO = 1.5V, unless otherwise noted.
PARAMETER
Input Offset Current Shift
Input Bias Current Match (Channel to Channel)
CONDITIONS
VCM = VEE to VCC
VCM = VCC (Note 4)
VCM = VEE (Note 4)
Large-Signal Voltage Gain
VO = 50mV to 2.8V, RL = 10k
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 2.5mA
Output Voltage Swing High
No Load
ISINK = 0.5mA
ISINK = 2.5mA
Short-Circuit Current
(Note 2)
Supply Current per Amplifier
MIN
TYP
1
0
1
0
1
250
1500
77
86
71
86
73
86
67
86
6
40
110
VCC – 0.012 VCC – 0.004
VCC – 0.100 VCC – 0.050
VCC – 0.250 VCC – 0.150
±10
±20
330
MAX
12
12
12
12
70
200
500
UNITS
nA
nA
nA
V/mV
dB
dB
dB
dB
mV
mV
mV
V
V
V
mA
µA
The l denotes the specifications which apply over the specified temperature range of 0°C < TA < 70°C. VS = 3V, 0V; VCM = 1.5V,
VO = 1.5V, unless otherwise noted.
SYMBOL
VOS
∆VOS
VOS TC
IB
∆IB
IOS
∆IOS
AVOL
CMRR
VOL
VOH
ISC
IS
PARAMETER
Input Offset Voltage (LT1366/LT1368)
CONDITIONS
VCM = VCC
VCM = VEE
Input Offset Voltage (LT1367/LT1369)
VCM = VCC
VCM = VEE
Input Offset Voltage Shift (LT1366/LT1368)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Offset Voltage Shift (LT1367/LT1369)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Offset Voltage Drift
(Note 3)
Input Bias Current
VCM = VCC
VCM = VEE
Input Bias Current Shift
VCM = VEE to VCC
Input Offset Current
VCM = VCC
VCM = VEE
Input Offset Current Shift
VCM = VEE to VCC
Input Bias Current Match (Channel to Channel)
VCM = VCC (Note 4)
VCM = VEE (Note 4)
Large-Signal Voltage Gain
VO = 50mV to 2.8V, RL = 10k
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 2.5mA
Output Voltage Swing High
No Load
ISOURCE = 0.5mA
ISOURCE = 2.5mA
Short-Circuit Current
(Note 2)
Supply Current per Amplifier
MIN
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
0
–45
TYP
200
200
200
200
200
250
200
250
2
15
–10
25
2
1
2
0
2
0
1
150
1500
76
83
70
83
72
83
66
83
9
45
120
VCC – 0.014 VCC – 0.005
VCC – 0.110 VCC – 0.055
VCC – 0.300 VCC – 0.180
±10
375
MAX
575
575
950
900
425
900
675
1900
6
45
0
90
UNITS
µV
µV
µV
µV
µV
µV
µV
µV
µV/°C
nA
nA
nA
15
15
15
15
15
nA
nA
nA
nA
nA
V/mV
dB
dB
dB
dB
mV
mV
mV
V
V
V
mA
µA
14
80
230
520
1366fb
LT1366/LT1367
LT1368/LT1369
Electrical
Characteristics
TA = 25°C, VS = ±15V, VCM = 0V, VO = 0V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage (LT1366/LT1368)
TYP
MAX
UNITS
VCM = VCC
VCM = VEE
200
200
700
700
µV
µV
Input Offset Voltage (LT1367/LT1369)
VCM = VCC
VCM = VEE
200
200
1000
900
µV
µV
Input Offset Voltage Shift (LT1366/LT1368)
Input Offset Voltage Match (Channel to Channel)
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
150
300
500
1300
µV
µV
Input Offset Voltage Shift (LT1367/LT1369)
Input Offset Voltage Match (Channel to Channel)
VCM = VEE to VCC
VCM = VEE, VCC (Notes 4, 5)
150
300
650
2000
µV
µV
IB
Input Bias Current
VCM = VCC
VCM = VEE
10
–10
35
0
nA
nA
∆IB
Input Bias Current Shift
VCM = VEE to VCC
20
70
nA
IOS
Input Offset Current
VCM = VCC
VCM = VEE
1.0
0.3
12
12
nA
nA
∆IOS
Input Offset Current Shift
VCM = VEE to VCC
1
12
nA
Input Bias Current Match (Channel to Channel)
VCM = VCC (Note 4)
VCM = VEE (Note 4)
1
1
12
12
nA
nA
∆VOS
CIN
Input Capacitance
AVOL
Large-Signal Voltage Gain
SR
Slew Rate (LT1368/LT1369)
CMRR
PSRR
MIN
0
–35
0
0
7.1
pF
VO = –14.7V to 14.7V, RL = 10k
VO = –10V to 10V, RL = 2k
1000
500
Channel Separation
VO = –10V to 10V, RL = 2k
120
135
dB
Slew Rate (LT1366/LT1367)
AV = –1, RL = Open, VO = ±10V,
Measured at VO = ±5V
0.13
V/µs
AV = –1, RL = Open, VO = ±10V,
Measured at VO = ±5V
0.065
V/µs
10000
10000
V/mV
V/mV
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
95
89
106
106
dB
dB
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Power Supply Rejection Ratio
VS = ±5V to ±15V
VS = ±5V to ±15V (Note 4)
PSRR Match (Channel to Channel)
93
87
106
106
dB
dB
90
84
110
105
dB
dB
VOL
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 10mA
VEE + 0.006
VEE + 0.040
VEE + 0.240
VOH
Output Voltage Swing High
No Load
ISINK = 0.5mA
ISINK = 2.5mA
VCC – 0.012 VCC – 0.004
VCC – 0.100 VCC – 0.050
VCC – 0.800 VCC – 0.400
ISC
Short-Circuit Current
(Note 2)
IS
Supply Current per Amplifier
±30
VEE + 0.012
VEE + 0.070
VEE + 0.500
V
V
V
±75
370
V
V
V
mA
550
µA
1366fb
LT1366/LT1367
LT1368/LT1369
Electrical
Characteristics
The l denotes the specifications which apply over the specified
temperature range of 0°C < TA < 70°C. VS = ±15V, VCM = 0V, VO = 0V, unless otherwise noted.
SYMBOL
VOS
∆VOS
VOS TC
IB
∆IB
IOS
∆IOS
AVOL
CMRR
PSRR
VOL
VOH
ISC
IS
PARAMETER
Input Offset Voltage (LT1366/LT1368)
CONDITIONS
VCM = VCC
VCM = VEE
Input Offset Voltage (LT1367/LT1369)
VCM = VCC
VCM = VEE
Input Offset Voltage Shift (LT1366/LT1368)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Offset Voltage Shift (LT1367/LT1369)
VCM = VEE to VCC
Input Offset Voltage Match (Channel to Channel) VCM = VEE, VCC (Notes 4, 5)
Input Offset Voltage Drift
(Note 3)
Input Bias Current
VCM = VCC
VCM = VEE
Input Bias Current Shift
VCM = VEE to VCC
Input Offset Current
VCM = VCC
VCM = VEE
Input Offset Current Shift
VCM = VEE to VCC
Input Bias Current Match (Channel to Channel)
VCM = VCC (Note 4)
VCM = VEE (Note 4)
Large-Signal Voltage Gain
VO = –14.7V to 14.7V, RL = 10k
VO = –10V to 10V, RL = 2k
Channel Separation
VO = –10V to 10V, RL = 2k
Common Mode Rejection Ratio (LT1366/LT1368) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Common Mode Rejection Ratio (LT1367/LT1369) VCM = VEE to VCC
VCM = VEE to VCC (Note 4)
CMRR Match (Channel to Channel)
Power Supply Rejection Ratio
VS = ±5V to ±15V
VS = ±5V to ±15V (Note 4)
PSRR Match (Channel to Channel)
Output Voltage Swing Low
No Load
ISINK = 0.5mA
ISINK = 10mA
Output Voltage Swing High
No Load
ISOURCE = 0.5mA
ISOURCE = 10mA
Short-Circuit Current
(Note 2)
Supply Current per Amplifier
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Applies to short circuits to ground for all split supplies and for
single supplies less than 20V. Short circuits to either supply for supplies
greater than 20V total may permanently damage the part. A heat sink may
be required to keep the junction temperature below the absolute maximum
rating when the output is shorted indefinitely.
MIN
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
0
–45
TYP
250
250
250
250
200
300
200
300
2
15
–10
25
MAX
850
850
1150
1000
525
1500
750
2300
8
45
0
90
2
15
1
15
2
15
0
2
15
0
1
15
750
6000
500
6000
110
135
95
103
89
103
92
103
86
103
80
105
75
100
VEE + 0.009 VEE + 0.014
VEE + 0.045 VEE + 0.080
VEE + 0.300 VEE + 0.600
VCC – 0.014 VCC – 0.005
VCC – 0.11 VCC – 0.055
VCC – 0.95 VCC – 0.500
±30
415
575
UNITS
µV
µV
µV
µV
µV
µV
µV
µV
µV/°C
nA
nA
nA
nA
nA
nA
nA
nA
V/mV
V/mV
dB
dB
dB
dB
dB
dB
dB
V
V
V
V
V
V
mA
µA
Note 3: This parameter is not 100% tested.
Note 4: Matching parameters are the difference between amplifiers A and
D and between B and C on the LT1367/LT1369; between the two amplifiers
on the LT1366/LT1368.
Note 5: Input offset voltage match is the difference in offset voltage
between amplifiers measured at both VCM = VEE and VCM = VCC.
1366fb
LT1366/LT1367
LT1368/LT1369
Typical Performance Characteristics
(The data presented here applies to the LT1366/LT1367/LT1368/LT1369 unless otherwise noted.)
PNP Stage VOS Distribution
(LT1366/LT1368)
25
20
15
10
30
N-PACKAGE
VS = 5V, 0V
VCM = 5V
20
15
10
5
0
–350 –250 –150 –50 50 150 250
INPUT OFFSET VOLTAGE (µV)
350
LT1366 TPC03
Input Bias Current
vs Common Mode Voltage
300
200
100
20
TA = 125°C
400
TA = 25°C
300
TA = –55°C
200
100
0
0
–50 –35 –20 –5 10 25 40 55 70 85 100
TEMPERATURE (°C)
TA = –55°C
10
5
TA = 25°C
0
–5
TA = 125°C
–10
–15
0
4
8 12 16 20 24 28 32
TOTAL SUPPLY VOLTAGE (V)
LT1366 TPC04
–20
–2
36
–1
0
4
3
5
2
1
COMMON MODE VOLTAGE (V)
6
LT1366 TPC06
LT1366 TPC05
Input Bias Current
vs Temperature
Output Saturation Voltage vs
Load Current (Output High)
50
VS = 5V, 0V
15
500
350
LT1366 TPC01
INPUT BIAS CURRENT (nA)
SUPPLY CURRENT PER AMPLIFIER (µA)
SUPPLY CURRENT PER AMPLIFIER (µA)
0
–350 –250 –150 –50 50 150 250
INPUT OFFSET VOLTAGE (µV)
350
600
VS = 5V, 0V
10
Supply Current vs Supply Voltage
500
VS = ±15V
15
LT1366 TPC02
Supply Current vs Temperature
400
20
5
5
0
–350 –250 –150 –50 50 150 250
INPUT OFFSET VOLTAGE (µV)
N-PACKAGE
VS = 5V, 0V
VCM = 0V TO 5V
25
PERCENT OF UNITS (%)
PERCENT OF UNITS (%)
25
30
N-PACKAGE
VS = 5V, 0V
VCM = 0V
PERCENT OF UNITS (%)
30
∆VOS-Shift Between PNP and NPN
Stages (LT1366/LT1368)
NPN Stage VOS Distribution
(LT1366/LT1368)
Output Saturation Voltage vs
Load Current (Output Low)
1000
1000
20
10
0
–10
–20
VS = 5V, 0V, VCM = 5V
VS = ±15V, VCM = 15V
VS = 5V, 0V, VCM = 0V
VS = ±15V, VCM = –15V
–30
SATURATION VOLTAGE (mV)
30
SATURATION VOLTAGE (mV)
INPUT BIAS CURRENT (nA)
40
100
TA = 85°C
TA = 25°C
10
TA = –55°C
100
TA = 85°C
TA = 25°C
10
TA = –55°C
–40
–50
–50 –35 –20 –5 10 25 40 55 70 85 100
TEMPERATURE (°C)
LT1366 TPC07
1
0.001
0.01
0.1
1
LOAD CURRENT (mA)
10
LT1366 TPC08
1
0.001
0.01
0.1
1
LOAD CURRENT (mA)
10
LT1366 TPC09
1366fb
LT1366/LT1367
LT1368/LT1369
Typical Performance Characteristics
(The data presented here applies to the LT1366/LT1367/LT1368/LT1369 unless otherwise noted.)
0.1Hz to 10Hz
Output Voltage Noise
Minimum Supply Voltage
Noise Voltage Spectrum
70
VS = ±2.5V
VCM = 0V
TA = 70°C
TA = 85°C
100
50
TA = 25°C
0
TA = –55°C
NOISE VOLTAGE nV/√Hz
150
70
VS = 5V, 0V
60
0.7
0.2
VCM = 4V
0.1
0
1
10
100
FREQUENCY (Hz)
1000
PHASE
40
30
GAIN
80
20
80
10
20
0
0
10
80
70
60
50
40
30
1M
LT1366 TPC16
140
120
60
PHASE
0
40
–10
20
–20
0
GAIN
–10
–20
–30
–20
–20
–40
–40
–40
–30
–60
10M
–50
10k
1k
100k
1M
FREQUENCY (Hz)
10k
1k
LT1366 TPC15
PSRR vs Frequency
(LT1368/LT1369)
120
VS = ±2.5V
100
80
POSITIVE SUPPLY
60
40
20
0
NEGATIVE SUPPLY
1k
10k
100k
FREQUENCY (Hz)
–60
10M
100k
1M
FREQUENCY (Hz)
LT1366 TPC14
POWER SUPPLY REJECTION RATIO (dB)
90
10k
100k
FREQUENCY (Hz)
100
40
120
VS = ±2.5V
1k
30
VS = ±2.5V
CL = 0.1µF
PSRR vs Frequency
(LT1366/LT1367)
100
20
100
20
CMRR vs Frequency
(LT1366 and LT1367)
110
40
60
LT1366 TPC13
120
50
120
PHASE SHIFT (DEG)
VCM = 2.5V
0.3
LT1366 TPC12
140
PHASE SHIFT (DEG)
VOLTAGE GAIN (dB)
0.6
1000
Gain and Phase Shift
vs Frequency (LT1368/LT1369)
VS = ±2.5V
50
0.4
10
100
FREQUENCY (Hz)
1
LT1366 TPC11
Gain and Phase Shift
vs Frequency (LT1366/LT1367)
0.5
VCM = 2.5V
20
TIME (1s/DIV)
VOLTAGE GAIN (dB)
0.8
VCM = 4V
30
0
5
POWER SUPPLY REJECTION RATIO (dB)
3
2
4
TOTAL SUPPLY VOLTAGE (V)
Noise Current Spectrum
CURRENT NOISE (pA/√Hz)
40
10
LT1366 TPC10
COMMON MODE REJECTION RATIO (dB)
50
NONFUNCTIONAL
1
VS = 5V, 0V
60
OUTPUT VOLTAGE (200nV/DIV)
CHANGE IN OFFSET VOLTAGE (µV)
200
1M
LT1366 TPC17
VS = ±2.5V
100
80
POSITIVE SUPPLY
60
40
20
NEGATIVE SUPPLY
0
1k
10k
100k
FREQUENCY (Hz)
1M
LT1366 TPC18
1366fb
LT1366/LT1367
LT1368/LT1369
Typical Performance Characteristics
(The data presented here applies to the LT1366/LT1367/LT1368/LT1369 unless otherwise noted.)
Gain-Bandwidth and Phase
Margin vs Supply Voltage
(LT1366/LT1367)
Channel Separation vs Frequency
–50
54
–60
48
–70
GBW
PHASE MARGIN
350
42
PHASE MARGIN (DEG)
–80
300
36
250
30
200
24
150
18
100
12
50
6
–140
0
30
–150
0
0
5
25
15
20
10
SUPPLY VOLTAGE (V)
–90
LT1368/LT1369
–100
–110
–120
LT1366/LT1367
–130
RL = 2k
5
0
RL = 10k
–5
–10
100
1k
FREQUENCY (Hz)
10
–20
5
–20 –15 –10 –5 0
10
OUTPUT VOLTAGE (V)
10k
LT1366 TPC20
Capacitive Load Handling
(LT1366/LT1367)
60
VS = 5V, 0V
50
60
VS = ±15V
AV = 1
50
CL = 0.22µF
OVERSHOOT (%)
50
AV = 1
40
AV = 5
30
40
20
Overshoot vs Load Current
(LT1368/LT1369)
VS = ±2.5V
AV = 1
60
15
LT1366 TPC21
Overshoot vs Load Current
(LT1368/LT1369)
70
OVERSHOOT (%)
10
–15
LT1366 TPC19
80
VS = ±15V
15
CL = 0.047µF
OVERSHOOT (%)
FREQUENCY (kHz)
400
VS = ±15V
VOUT = ±1VP-P
RL = 2k
INPUT VOLTAGE (µV)
60
450
CHANNEL SEPARATION (dB)
500
Open-Loop Gain
20
CL = 0.1µF
30
20
CL = 0.22µF
40
CL = 0.047µF
30
CL = 0.1µF
20
20
0
10
AV = 10
100
1k
10k
CAPACITIVE LOAD (pF)
10
10
0
–10
100k
–5
0
5
LOAD CURRENT (mA)
LT1366 TPC22
CHANGE IN OFFSET VOLTAGE (µV)
SLEW RATE (V/µs)
0.14
0.12
0.10
0
4
THD + Noise vs
Peak-to-Peak Voltage
80
AV = –1
0.16
8 12 16 20 24 28 32
TOTAL SUPPLY VOLTAGE (V)
36
LT1366 TPC25
10
LT1366 TPC24
Warm-Up Drift vs Time
0.18
–5
0
5
LOAD CURRENT (mA)
LT1366 TPC23
Slew Rate vs Supply Voltage
0.20
0
–10
10
10
60
S8 PACKAGE
VS = ±15V
40
20
0
–20
N8 PACKAGE
VS = ±2.5V
–40
N8 PACKAGE
VS = ±15V
–60
–80
0
f = 1kHz
RL = 10k
(ALL CURVES)
1
S8 PACKAGE
VS = ±2.5V
15 30 45 60 75 90 105 120 135 150
TIME AFTER POWER-UP (SEC)
LT1366 TPC26
THD + NOISE (%)
10
0.1
VS = ±1.5V
AV = 1
0.01
0.001
VS = ±1.5V
AV = –1
0
1
2
3
VIN(P-P) (V)
VS = ±2.5V
AV = 1
VS = ±2.5V
AV = –1
4
5
LT1366 TPC27
1366fb
10
LT1366/LT1367
LT1368/LT1369
Typical Performance Characteristics
(The data presented here applies to the LT1366/LT1367/LT1368/LT1369 unless otherwise noted.)
Large-Signal Response
(LT1366/LT1367)
THD + Noise vs Frequency
0.1
5mV/DIV
VS = ±1.5V
VIN = 2VP-P
RL = 10k
5V/DIV
THD + NOISE (%)
1
Small-Signal Response
(LT1366/LT1367)
0V
AV = 1
0.01
AV = –1
VS = ±15V
UNITY GAIN
0.001
0.01
0.1
1
FREQUENCY (kHz)
100µs/DIV
VS = ±15V
UNITY GAIN
LT1366 TPC29
2µs/DIV
LT1366 TPC30
10
LT1366 TPC28
Applications information
Rail-to-Rail Operation
portions of the input common mode range. Lateral devices
are used in both input stages, eliminating the need for
clamps across the input pins. Each input stage is trimmed
for offset voltage. A complementary output configuration
(Q23 through Q26) is employed to create an output stage
with rail-to-rail swing. The amplifier is fabricated on Linear
The LT1366 family differs from conventional op amps in the
design of both the input and output stages. Figure 1 shows
a simplified schematic of the amplifier. The input stage
consists of two differential amplifiers, a PNP stage Q1/Q2
and an NPN stage Q3/Q4, which are active over different
V+
D4
I1
D7
D6
D5
Q21
Q17
Q10
Q11
Q5
Q23
Q16
V–
V–
V–
V–
IN+
V+
Q1 Q2
D1
IN–
V+
– 300mV
V+
C1
OUT
C2
V+
CC
D2
Q3 Q4
Q12
Q6
Q9
Q25
Q26
Q22
Q18
Q13
D3
Q20
Q14 Q15
Q7
Q8
V+
Q24
Q19
D8
D7
V–
LT1366 FO1
Figure 1. LT1366 Simplified Schematic Diagram
1366fb
11
LT1366/LT1367
LT1368/LT1369
Applications information
The collector currents of the two input pairs are combined
in the second stage, consisting of Q7 through Q11. Most
of the voltage gain in the amplifier is contained in this
stage. Differential amplifier Q14/Q15 buffers the output
of the second stage, converting the output voltage to differential currents. The differential currents pass through
current mirrors D4/Q17 and D5/Q16, and are converted to
differential voltages by Q18 and Q19. These voltages are
also buffered and applied to the output Darlington pairs
Q23/Q24 and Q25/Q26. Capacitors C1 and C2 form local
feedback loops around the output devices, lowering the
output impedance at high frequencies.
Input Offset Voltage
Since the amplifier has two input stages, the input offset
voltage changes depending upon which stage is active.
The input offsets are random, but bounded voltages. When
the amplifier switches between stages, offset voltages
may go up, down, or remain flat; but will not exceed the
guaranteed limits. This behavior is illustrated in three
distribution plots of input offset voltage in the Typical
Performance Characteristics section.
Overdrive Protection
Two circuits prevent the output from reversing polarity
when the input voltage exceeds the common mode range.
When the noninverting input exceeds the positive supply
by approximately 300mV, the clamp transistor Q12 (Figure 1) turns on, pulling the output of the second stage
low, which forces the output high. For inputs below the
negative supply, diodes D1 and D2 turn on, overcoming
the saturation of the input pair Q1/Q2.
110
MEASURED AS A
FOLLOWER
100
INPUT BIAS CURRENT (nA)
A simple comparator Q5 steers current from current source
I1 between the two input stages. When the input common
mode voltage VCM is near the negative supply, Q5 is reverse biased, and I1 becomes the tail current for the PNP
differential pair Q1/Q2. At the other extreme, when VCM
is within about 1.3V from the positive supply, Q5 diverts
I1 to the current mirror D3/Q6, which furnishes the tail
current for the NPN differential pair Q3/Q4.
When overdriven, the amplifier draws input current that
exceeds the normal input bias current. Figures 2 and 3
show some typical overdrive currents as a function of
input voltage. The input current must be less than 1mA of
positive overdrive or less than 7mA of negative overdrive,
for the phase reversal protection to work properly. When
the amplifier is severely overdriven, an external resistor
should be used to limit the overdrive current. In addition
to overdrive protection, the amplifier is protected against
ESD strokes up to 4kV on all pins.
90
+
80
–
70
T = 25°C
60
50
T = 85°C
40
T = –55°C
T = 70°C
30
20
10
0
–500
–300
–100 VS 100
300
500
COMMON MODE VOLTAGE RELATIVE TO
POSITIVE SUPPLY (mV)
LT1366 F02
Figure 2. Input Bias Current vs Common Mode Voltage
0
–10
INPUT BIAS CURRENT (nA)
Technology’s proprietary complementary bipolar process,
which ensures very similar DC and AC characteristics for
the output devices Q24 and Q26.
MEASURED AS A FOLLOWER
+
–20
–
–30
–40
–50
T = –55°C
–60
–70
T = 25°C
T = 70°C
T = 85°C
–80
–90
–100
–110
–800
–200
200
–600
–400
VS
COMMON MODE VOLTAGE RELATIVE TO
NEGATIVE SUPPLY (mV)
LT1366 F03
Figure 3. Input Bias Current vs Common Mode Voltage
1366fb
12
LT1366/LT1367
LT1368/LT1369
Applications information
Improved Supply Rejection in the LT1368/LT1369
The LT1368/LT1369 are variations of the LT1366/LT1367
offering greater supply rejection and lower high frequency
output impedance. The LT1368/LT1369 require a 0.1µF load
capacitance for compensation. The output capacitance
forms a filter, which reduces pickup from the supply and
lowers the output impedance. This additional filtering is
helpful in mixed analog/digital systems with common supplies, or systems employing switching supplies. Filtering
also reduces high frequency noise, which may be beneficial
when driving A/D converters.
Figure 4 shows the outputs of the LT1366/LT1368 perturbed
by a 200mVP-P 50kHz square wave added to the positive
supply. The LT1368’s power supply rejection is about ten
times greater than that of the LT1366 at 50kHz. Note the
5-to-1 scale change in the output voltage traces.
The tolerance of the external compensation capacitor is
not critical. The plots of Overshoot vs Load Current in the
Typical Performance Characteristics section illustrate the
effect of a capacitive load.
V+ (AC)
100mV/DIV
V+ (AC)
100mV/DIV
VOUT
100mV/DIV
VOUT
20mV/DIV
2µs/DIV
2µs/DIV
LT1366 F04a
Figure 4a. LT1366 Power Supply Rejection Test
LT1366 F04b
Figure 4b. LT1368 Power Supply Rejection Test
Typical Applications
Buffering A/D Converters
Figure 5 shows the LT1368 driving an LTC®1288 2-channel micropower A/D converter (ADC). The LTC1288 can
accommodate voltage references and input signals equal
to the supply rails. The sampling nature of this ADC
eliminates the need for an external sample-and-hold, but
may call for a drive amplifier because of the ADC’s 12µs
settling requirement. The LT1368’s rail-to-rail operation
and low input offset voltage make it well-suited for low
power, low frequency A/D applications. Either the LT1366
or LT1368 could be used for this application. However,
for low frequencies (f < 1kHz) the LT1368 provides better
supply rejection.
VCC
1µF
0.1µF
V0
+
1/2 LT1368
0.1µF
–
CS/SHDN
VCC (REF)
CH0
CLK
TO µP
LTC1288
V1
+
1/2 LT1368
–
CH1
DOUT
GND
DIN
LT1366 FO5
0.1µF
Figure 5. 2-Channel Low Power A/D Converter
1366fb
13
LT1366/LT1367
LT1368/LT1369
TYPICAL APPLICATIONS
Precision Low Dropout Regulator
Microprocessors and complex digital circuits frequently
specify tight control of power supply characteristics. The
circuit shown in Figure 6 provides a precise 3.6V, 1A output
from a minimum 3.8V input voltage. The circuit’s nominal
operating voltage is 4.75V ±5%. The voltage reference
and resistor ratios determine output voltage accuracy,
while the LT1366’s high gain enforces 0.2% line and load
regulation. Quiescent current is about 1mA and does not
change appreciably with supply or load. All components
are available in surface mount packages.
The regulator’s main loop consists of A1 and a logic-level
FET, Q1. The output is fed back to the op amp’s positive
input because of the phase inversion through Q1. The
regulator’s frequency response is limited by Q1’s roll-off
and the phase lead introduced by the output capacitor’s
effective series resistance (ESR). Two pole-zero networks
compensate for these effects. The pole formed with R5
and C2 rolls off the gain set with the feedback network,
while the pole formed with R7 and C3 rolls off A1’s gain
directly, which is the dominant influence on settling time.
The zeros formed with R6 and C2, and R8 and C3 provide
phase boost near the unity-gain crossover, which increases
the regulator’s phase margin. Although not directly part
of the compensation, R9 decouples the op amp’s output
from Q1’s large gate capacitance.
A second loop provides a foldback current limit. A2 compares the sense voltage across R1 with 50mV referenced
to the positive rail. When the sense voltage exceeds the
reference, A2’s output drives Q1’s gate positive via A1.
In current limit, the output voltage collapses and the
current limit LED (D1) turns on causing about 30mV to
drop across R3. A2 regulates Q1’s drain current so that
the deficit between the 50mV reference and the voltage
across R3 is made up across the sense resistor. The
reduced sense voltage is 20mV, which sets the current
limit to about 400mA. As the supply voltage increases, the
voltage across R3 increases, and the current limit folds
back to a lower level. The current limit loop deactivates
when the load current drops below the regulated output
current. When the supply turns on rapidly, C1 bypasses
the fold back circuit allowing the regulator to start-up into
a heavy load.
Q1 does not require a heat sink. When mounted on a type
FR4 PC board, Q1 has a thermal resistance of 50°C/W. At
1.4W worst-case dissipation, Q1 can operate up to 80°C.
VIN = 4.75V ±5%
R8
2k
10k
R7
13k
C3
6.8nF
–
A1
1/2 LT1366
R3
20Ω
R9
100Ω
+
Q1
Si9433DY
1.5k
+
+
50mV
–
C1
10µF
R1
0.05Ω
R2
2k
+
R4
10k
C5
47µF
0.1µF
–
A2
1/2 LT1366
D1
+
D2
1N4148
5k
VOUT
3.6V
1A
38.5k*
C4
1µF
LT1004-1.2
R5*
20k
C2
6.8nF
R6
6.2k
RMIN**
1k
4.75V TO 3.6V LDO AT 1A
*1% METAL FILM
**SET RMIN BASED ON LOAD CHARACTERISTICS
+
CLOAD
10µF
Q2
2N3904
23.2k
LT1366 F06
Figure 6. Precision 3.6V, 1A Low Dropout Regulator
1366fb
14
LT1366/LT1367
LT1368/LT1369
TYPICAL APPLICATIONS
High Side Current Source
The wide compliance current source shown in Figure 7
takes advantage of the LT1366’s ability to measure small
signals near the positive supply rail. The LT1366 adjusts
Q1’s gate voltage to force the voltage across the sense
resistor (RSENSE) to equal the voltage from the supply to
the potentiometer’s wiper. A rail-to-rail op amp is needed
because the voltage across the sense resistor must drop
to zero when the divided reference voltage is set to zero.
Q2 acts as a constant current sink to minimize error in the
reference voltage when the supply voltage varies.
The circuit can operate over a wide supply range
(5V < VCC < 30V). At low input voltage, circuit operation
is limited by the MOSFET’s gate drive requirements. At
VCC
RSENSE
0.2Ω
1k
0.0033µF
–
LT1004-1.2
1/2 LT1366
RP
10k
100Ω
+
Q1
MTP23P06
ILOAD
40k
LT1366 F07
Figure 7. High Side Current Source
VIN
–
A1
1/4 LT1367
which is easily achievable with a small heat sink. Input
voltages greater than 5V require the use of a larger heat
sink or a reduction of the output current.
The circuit’s supply regulation is about 0.03%/V. The output
impedance is equal to the MOSFET’s output impedance
multiplied by the op amp’s open-loop gain. Degradations in
current-source compliance occur when the voltage across
the MOSFET’s on-resistance and the sense resistor drops
below the voltage required to maintain the desired output
current. This condition occurs when:
An LT1367 is used in Figure 8 to form a 4th order Butterworth filter. The filter is a simplified state variable architecture consisting of two cascaded 2nd order sections.
Each section uses the 360 degree phase shift around
C2
10,000pF
R2*
8.6k
10,000pF
–
A2
1/4 LT1367
+
+
10,000pF
11.8k*
–
A3
1/4 LT1367
21.5k*
VOUT
+
10k
10k
–
A4
1/4 LT1367
+
29.5k*
3.3V
θHS = θJA(SYSTEM) – θJC(FET)
= (125°C – 70°C)/5W – 1.25°C/W
= 11°C/W –1.25°C/W
= 9.75°C/W
Single Supply, 1kHz, 4th Order Butterworth Filter
Q2
2N4340
R1*
29.5k
The circuit delivers 1A at 200mV of sense voltage. With a
5V input supply, the power dissipation is 5W. For operation at 70°C ambient temperature, the MOSFET’s heat sink
must have a thermal resistance of:
[VCC – VOUT] < [ILOAD • (RSENSE + RON)]
5V < VCC < 30V
0A < ILOAD < 1A AT VCC = 5V
0mA < ILOAD < 160mA AT VCC = 30V
C1
10,000pF
high input voltage, circuit operation is limited by the
LT1366’s absolute maximum ratings and the output power
requirements.
11.8k*
1µF
*1% RESISTORS
LT1366 F08
Figure 8. 4-Pole 1kHz, 3.3V Single Supply, State Variable Filter Using the LT1367
1366fb
15
LT1366/LT1367
LT1368/LT1369
TYPICAL APPLICATIONS
the 2 op amp loop to create a negative summing junction
at A1’s positive input1. The circuit has low sensitivities for
center frequency and Q, which are set with the following
equations:
2 = 1/(R1 • C1 • R2 • C2)
ω0
10k
V+
2
–
VIN
1
1/2 LT1366
3
+
VOUT
SIGNAL AMP
where:
R1 = 1/(ω0 • Q • C1) and R2 = Q/(ω0 • C2).
1M
The DC bias applied to A2 and A4, half supply, is not needed
when split supplies are available. The circuit swings railto-rail in the passband making it an excellent anti-aliasing
filter for ADCs. The amplitude response is flat to 1kHz then
rolls off at 80dB/decade.
+
7
1/2 LT1366
–
22pF
5
6
CANCELLATION AMP
1366 F10
1James Hahn, “State Variable Filter Trims Predecessor’s Component Count,” Electronics, April
1M
21, 1982.
Figure 10. Input Bias Current Cancellation
180
0
GAIN
144
PHASE
–20
72
36
–40
0
–36
–60
PHASE (DEG)
GAIN (dB)
VCC
108
–72
–108
–80
100
RP
10k
+
1/2 LT1366
–
RL
–144
1k
FREQUENCY (Hz)
–180
10k
1366 F11
1366 F09
Figure 9. Frequency Response of 4th Order Butterworth Filter
Figure 11. Rail-to-Rail Potentiometer Buffer
1366fb
16
LT1366/LT1367
LT1368/LT1369
package description
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.300 – .325
(7.620 – 8.255)
+.035
.325 –.015
8.255
+0.889
–0.381
.130 p .005
(3.302 p 0.127)
.045 – .065
(1.143 – 1.651)
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
.255 p .015*
(6.477 p 0.381)
.120
(3.048) .020
MIN (0.508)
MIN
.018 p .003
.100
(2.54)
BSC
N8 1002
(0.457 p 0.076)
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.050 BSC
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 p.005
8
.245
MIN
.160 p.005
.010 – .020
s 45o
(0.254 – 0.508)
NOTE:
1. DIMENSIONS IN
5
.150 – .157
(3.810 – 3.988)
NOTE 3
1
RECOMMENDED SOLDER PAD LAYOUT
.053 – .069
(1.346 – 1.752)
0o– 8o TYP
.016 – .050
(0.406 – 1.270)
6
.228 – .244
(5.791 – 6.197)
.030 p.005
TYP
.008 – .010
(0.203 – 0.254)
7
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 0303
1366fb
17
LT1366/LT1367
LT1368/LT1369
package description
S Package
14-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.337 – .344
(8.560 – 8.738)
NOTE 3
.045 p.005
.050 BSC
14
N
12
11
10
9
8
N
.245
MIN
.160 p.005
.228 – .244
(5.791 – 6.197)
1
.030 p.005
TYP
13
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
s 45o
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
1
2
3
4
5
.053 – .069
(1.346 – 1.752)
NOTE:
1. DIMENSIONS IN
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
7
.004 – .010
(0.101 – 0.254)
0o – 8o TYP
.016 – .050
(0.406 – 1.270)
6
.150 – .157
(3.810 – 3.988)
NOTE 3
.050
(1.270)
BSC
S14 0502
1366fb
18
LT1366/LT1367
LT1368/LT1369
Revision History
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
03/10
Change to Absolute Maximum Ratings
Updated Format of Order Information Section
Change to Electrical Characteristics Note
2
2
3, 4, 5, 6, 7
1366fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1366/LT1367
LT1368/LT1369
Typical Application
Instrumentation Amplifier
V+
0.1µF
+
10M
GUARD
1/4
LT1367
A1A
–
RF
102k
+
RG
11.3k
+
+
1/4
LT1367
A1C
1/4
LT1367
A1B
200Ω
INPUTS
100k
10k
OUTPUT
–
–
10M
–
10M
22pF
GUARD
–
( )
1/4
LT1367
A1D
R
GAIN = 10 1 + F = 100
RG
RG
11.3k
RF
102k
10k
1366 TA03
+
BW = 30kHz
100k
Related Parts
PART
DESCRIPTION
COMMENTS
LT1078/LT1079
Dual/Quad 55µA Max, Single Supply, Precision Op Amps
Input/Output Common Mode Includes Ground, 70µV VOS(MAX) and
2.5µV/°C Drift (Max), 200kHz GBW, 0.07V/µs Slew Rate
LTC1152
Rail-to-Rail Input, Rail-to-Rail Output, Zero-Drift Amplifier
High DC Accuracy, 10µV VOS(MAX), 100nV/°C Drift, 1MHz GBW,
1V/µs Slew Rate, Supply Current 2.2mA (Max), Single Supply,
Can Be Configured for C-Load™ Operation
LT1178/LT1179
Dual/Quad 17µA Max, Single Supply, Precision Op Amps
Input/Output Common Mode Includes Ground, 70µV VOS(MAX) and
4µV/°C Drift (Max), 85kHz GBW, 0.04V/µs Slew Rate
LT1211/LT1212
Dual/Quad 14MHz, 7V/µs, Single Supply, Precision Op Amps
Input Common Mode Includes Ground, 275µV VOS(MAX) and
6µV/°C Drift (Max), Supply Current 1.8mA per Op Amp (Max)
LT1495/LT1496
1.5µA, Rail-to-Rail Input/Output Dual/Quad
375µV VOS(MAX), 2µV/°C Drift (Max), Over-The-Top® Input
1366fb
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
LT 0310 REV B • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 1995