LINER LT1801IDD

LT1801/LT1802
Dual/Quad 80MHz, 25V/µs
Low Power Rail-to-Rail Input and
Output Precision Op Amps
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
The LT ®1801/LT1802 are dual/quad, low power, high
speed rail-to-rail input and output operational amplifiers
with excellent DC performance. The LT1801/LT1802 feature reduced supply current, lower input offset voltage,
lower input bias current and higher DC gain than other
devices with comparable bandwidth.
Gain Bandwidth Product: 80MHz
Input Common Mode Range Includes Both Rails
Output Swings Rail-to-Rail
Low Voltage Operation: Single or Split Supplies
2.3V to 12.6V
Low Quiescent Current: 2mA/Amplifier Max
Input Offset Voltage: 350µV Max
Input Bias Current: 250nA Max
3mm × 3mm × 0.8mm DFN Package
Large Output Current: 50mA Typ
Low Voltage Noise: 8.5nV/√Hz Typ
Slew Rate: 25V/µs Typ
Common Mode Rejection: 105dB Typ
Power Supply Rejection: 97dB Typ
Open-Loop Gain: 85V/mV Typ
Operating Temperature Range: – 40°C to 85°C
LT1801 is Available in 8-Lead SO, MS8 and DFN
Packages
LT1802 is Available in 14-Lead SO Package
Typically, the LT1801/LT1802 have an input offset voltage
of less than 100µV, an input bias current of less than 50nA
and an open-loop gain of 85 thousand.
The LT1801/LT1802 have an input range that includes
both supply rails and an output that swings within 20mV
of either supply rail to maximize the signal dynamic range
in low supply applications.
The LT1801/LT1802 maintain their performance for supplies from 2.3V to 12.6V and are specified at 3V, 5V and
±5V supplies. The inputs can be driven beyond the supplies without damage or phase reversal of the output.
The LT1801 is available in the MS8, SO-8 and the 3mm ×
3mm × 0.8mm dual fine pitch leadless package (DFN) with
the standard dual op amp pinout. The LT1802 features the
standard quad op amp configuration and is available in the
14-pin plastic SO package. The LT1801/LT1802 can be
used as plug-in replacements for many op amps to improve input/output range and performance.
U
APPLICATIO S
■
■
■
■
■
Low Voltage, High Frequency Signal Processing
Driving A/D Converters
Rail-to-Rail Buffer Amplifiers
Active Filters
Video Line Driver
For a single version of these amplifiers, see the LT1800
data sheet.
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
U
1MHz Filter Frequency Response
TYPICAL APPLICATIO
3V, 1MHz, 4th Order Butterworth Filter
0
909Ω
909Ω
2.67k
VIN
220pF
GAIN (dB)
–20
47pF
1.1k
–
3V
1.1k
2.21k
1/2 LT1801
+
22pF
470pF
–
–40
–60
–80
1/2 LT1801
+
VOUT
–100
–120
VS /2
18012 TA01
1k
10k
100k
1M
FREQUENCY (Hz)
10M
100M
18012 TA02
18012fb
1
LT1801/LT1802
W W
W
AXI U
U
ABSOLUTE
RATI GS
(Note 1)
Total Supply Voltage (VS– to VS+) ......................... 12.6V
Input Current (Note 2) ........................................ ±10mA
Output Short-Circuit Duration (Note 3) ............ Indefinite
Operating Temperature Range (Note 4) .. – 40°C to 85°C
Specified Temperature Range (Note 5) ... – 40°C to 85°C
Junction Temperature .......................................... 150°C
Storage Temperature Range ................. – 65°C to 150°C
Maximum Junction Temperature (DD Package) ... 125°C
Storage Temperature (DD Package) ..... – 65°C to 125°C
Lead Temperature (Soldering, 10 sec).................. 300°C
U
U
W
PACKAGE/ORDER I FOR ATIO
TOP VIEW
A
+IN A 3
V
OUT A
–IN A
+IN A
V–
7 OUT B
–IN A 2
–
TOP VIEW
8 V+
OUT A 1
6 –IN B
B
4
5 +IN B
1
2
3
4
8
7
6
5
V+
OUT B
–IN B
+IN B
MS8 PACKAGE
8-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 160°C/ W, (Note 10)
EXPOSED PAD INTERNALLY CONNECTED TO V–.
(PCB CONNECTION OPTIONAL)
TJMAX = 150°C, θJA = 250°C/ W, (Note 10)
ORDER PART
NUMBER
DD PART
MARKING
ORDER PART
NUMBER
MS8 PART
MARKING
LT1801CDD
LT1801IDD
LAAM*
LT1801CMS8
LT1801IMS8
LTYR
LTYS
TOP VIEW
OUT A 1
+IN A 3
V– 4
–
+
–
+
13 –IN D
–IN A 2
8
V+
7
OUT B
6
–IN B
5
+IN B
+IN A 3
–IN A 2
14 OUT D
OUT A 1
TOP VIEW
S8 PACKAGE
8-LEAD PLASTIC SO
A
D
V+ 4
+IN B 5
12 +IN D
11 V –
B
C
10 +IN C
–IN B 6
9
–IN C
OUT B 7
8
OUT C
S PACKAGE
14-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 190°C/ W, (Note 10)
TJMAX = 150°C, θJA = 160°C/ W, (Note 10)
ORDER PART
NUMBER
S8 PART
MARKING
ORDER PART
NUMBER
LT1801CS8
LT1801IS8
1801
1801I
LT1802CS
LT1802IS
Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges.
18012fb
2
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
VOS
Input Offset Voltage
∆VOS
IB
IOS
MIN
TYP
MAX
UNITS
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
VCM = VS
75
140
175
0.5
350
500
800
3
µV
µV
µV
mV
Input Offset Shift
VCM = 0V to VS – 1.5V
20
185
µV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
100
150
280
650
900
1200
µV
µV
µV
Input Bias Current
VCM = 1V
VCM = VS
25
500
250
1500
nA
nA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = 1V
VCM = VS
25
25
350
500
nA
nA
Input Offset Current
VCM = 1V
VCM = VS
25
25
200
200
nA
nA
Input Noise Voltage
0.1Hz to 10Hz
1.4
µVP-P
en
Input Noise Voltage Density
f = 10kHz
8.5
nV/√Hz
in
Input Noise Current Density
f = 10kHz
1
pA/√Hz
CIN
Input Capacitance
AVOL
Large-Signal Voltage Gain
CMRR
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 9)
VOL
Input Common Mode Range
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
Minimum Supply Voltage (Note 6)
Output Voltage Swing Low (Note 7)
VOH
Output Voltage Swing High (Note 7)
ISC
Short-Circuit Current
IS
GBW
SR
FPBW
HD
tS
∆G
∆θ
Supply Current per Amplifier
Gain Bandwidth Product
Slew Rate
Full Power Bandwidth
Harmonic Distortion
Settling Time
Differential Gain (NTSC)
Differential Phase (NTSC)
PSRR
2
VS = 5V, VO = 0.5V to 4.5V, RL = 1k at VS/2
VS = 5V, VO = 1V to 4V, RL = 100Ω at VS/2
VS = 3V, VO = 0.5V to 2.5V, RL = 1k at VS/2
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
VS = 2.5V to 10V, VCM = 0V
VS = 2.5V to 10V, VCM = 0V
No Load
ISINK = 5mA
ISINK = 20mA
No Load
ISOURCE = 5mA
ISOURCE = 20mA
VS = 5V
VS = 3V
Frequency = 2MHz
VS = 5V, AV = – 1, RL = 1k, VO = 4VP-P
VS = 5V, AV = 1, VO = 4VP-P
VS = 5V, AV = 1, RL = 1k, VO = 2VP-P, fC = 500kHz
0.01%, VS = 5V, VSTEP = 2V, AV = 1, RL = 1k
VS = 5V, AV = 2, RL = 150Ω
VS = 5V, AV = 2, RL = 150Ω
35
3.5
30
85
78
79
72
0
78
72
20
20
40
12.5
pF
85
8
85
105
97
105
97
VS
97
97
2.3
16
85
225
18
120
450
45
40
1.6
80
25
2
–75
250
0.35
0.4
2.5
60
200
500
60
250
800
2
V/mV
V/mV
V/mV
dB
dB
dB
dB
V
dB
dB
V
mV
mV
mV
mV
mV
mV
mA
mA
mA
MHz
V/µs
MHz
dBc
ns
%
Deg
18012fb
3
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the temperature range of
0°C < TA < 70°C. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
VOS
Input Offset Voltage
∆VOS
Input Offset Shift
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VOS TC
IB
Input Offset Voltage Drift (Note 8)
Input Bias Current
IOS
Input Bias Current Match
(Channel-to-Channel) (Note 9)
Input Offset Current
AVOL
Large-Signal Voltage Gain
CMRR
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 9)
VOL
Input Common Mode Range
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
Minimum Supply Voltage (Note 6)
Output Voltage Swing Low (Note 7)
VOH
Output Voltage Swing High (Note 7)
ISC
Short-Circuit Current
IS
GBW
SR
Supply Current per Amplifier
Gain Bandwidth Product
Slew Rate
PSRR
CONDITIONS
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
VCM = VS
VCM = 0V to VS – 1.5V
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
MIN
●
●
●
●
●
●
●
●
●
VCM = 1V
VCM = VS – 0.2V
VCM = 1V
VCM = VS – 0.2V
VCM = 1V
VCM = VS – 0.2V
VS = 5V, VO = 0.5V to 4.5V, RL = 1k at VS/2
VS = 5V, VO = 1V to 4V, RL = 100Ω at VS/2
VS = 3V, VO = 0.5V to 2.5V, RL = 1k at VS/2
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
●
●
●
●
●
●
●
●
●
●
●
●
●
●
VS = 2.5V to 10V, VCM = 0V
VS = 2.5V to 10V, VCM = 0V
●
●
25
2.5
20
82
74
76
68
0
74
68
●
No Load
ISINK = 5mA
ISINK = 20mA
No Load
ISOURCE = 5mA
ISOURCE = 20mA
VS = 5V
VS = 3V
●
●
●
●
●
●
●
●
20
15
●
Frequency = 2MHz
VS = 5V, AV = – 1, RL = 1k, VO = 4VP-P
●
●
35
11
TYP
125
140
290
0.6
30
200
200
275
1.5
50
550
25
25
25
25
75
6
75
101
93
101
93
MAX
500
650
950
3.5
275
850
1250
1500
5
300
2000
400
600
300
300
VS
91
91
2.3
18
100
300
25
150
600
40
30
2
75
22
2.5
80
225
600
80
300
950
2.8
UNITS
µV
µV
µV
mV
µV
µV
µV
µV
µV/°C
nA
nA
nA
nA
nA
nA
V/mV
V/mV
V/mV
dB
dB
dB
dB
V
dB
dB
V
mV
mV
mV
mV
mV
mV
mA
mA
mA
MHz
V/µs
18012fb
4
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the temperature range of
– 40°C < TA < 85°C. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted. (Note 5)
SYMBOL PARAMETER
CONDITIONS
VOS
Input Offset Voltage
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
VCM = VS
●
●
●
●
∆VOS
Input Offset Shift
VCM = 0V to VS – 1.5V
●
30
300
µV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = 0V
VCM = 0V (MS8)
VCM = 0V (DD)
●
●
●
200
280
320
1250
1600
1800
µV
µV
µV
●
1.5
5
VCM = VS – 0.2V
●
●
50
600
400
2250
nA
nA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = 1V
VCM = VS – 0.2V
●
●
25
25
450
700
nA
nA
IOS
Input Offset Current
VCM = 1V
VCM = VS – 0.2V
●
●
25
25
350
350
nA
nA
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 0.5V to 4.5V, RL = 1k at VS/2
VS = 5V, VO = 1.5V to 3.5V, RL = 100Ω at VS/2
VS = 3V, VO = 0.5V to 2.5V, RL = 1k at VS/2
●
●
●
20
2
17.5
65
6
65
V/mV
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
●
●
81
73
101
93
dB
dB
CMRR Match (Channel-to-Channel) (Note 9)
VS = 5V, VCM = 0V to 3.5V
VS = 3V, VCM = 0V to 1.5V
●
●
75
67
101
93
dB
dB
VOS TC
Input Offset Voltage Drift (Note 8)
IB
Input Bias Current
MIN
TYP
MAX
UNITS
175
200
320
0.75
700
850
1150
4
µV
µV
µV
mV
µV/°C
●
0
VS = 2.5V to 10V, VCM = 0V
●
73
PSRR Match (Channel-to-Channel) (Note 9)
VS = 2.5V to 10V, VCM = 0V
●
67
Minimum Supply Voltage (Note 6)
VCM = VO = 0.5V
●
2.3
2.5
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 10mA
●
●
●
15
105
170
90
250
400
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 10mA
●
●
●
25
150
300
90
350
700
mV
mV
mV
ISC
Short-Circuit Current
VS = 5V
VS = 3V
●
●
IS
Supply Current per Amplifier
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
12.5
12.5
●
VS
90
90
dB
30
30
2.1
V
dB
mA
mA
3
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz
●
25
70
MHz
SR
Slew Rate
VS = 5V, AV = – 1, RL = 1k, VO = 4V
●
9
18
V/µs
18012fb
5
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = ±5V, VCM = 0V, VOUT = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
VOS
Input Offset Voltage
∆VOS
Input Offset Shift
VCM = VS–
VCM = VS– (MS8)
VCM = VS– (DD)
VCM = VS+
VCM = VS– to VS+ – 1.5V
VCM = VS–
VCM = VS– (MS8)
VCM = VS– (DD)
VCM = VS– + 1V
VCM = VS+
VCM = VS– + 1V
VCM = VS+
VCM = VS– + 1V
VCM = VS+
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
IB
Input Bias Current
Input Bias Current Match
(Channel-to-Channel) (Note 9)
IOS
Input Offset Current
MIN
TYP
MAX
UNITS
150
180
260
0.7
600
750
1050
3.5
µV
µV
µV
mV
30
475
µV
150
275
325
1000
1300
1600
µV
µV
µV
25
400
250
1500
nA
nA
20
20
350
500
nA
nA
20
20
250
250
nA
nA
Input Noise Voltage
0.1Hz to 10Hz
1.4
µVP-P
en
Input Noise Voltage Density
f = 10kHz
8.5
nV/√Hz
in
Input Noise Current Density
f = 10kHz
1
pA/√Hz
CIN
Input Capacitance
f = 100kHz
2
pF
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –2V to 2V, RL = 100Ω
25
2.5
70
7
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VCM = VS– to 3.5V
85
109
dB
79
109
CMRR Match (Channel-to-Channel) (Note 9)
VCM = VS
– to 3.5V
VS–
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
VS+
VS+
= 2.5V to 10V, VS–
= 2.5V to 10V, VS–
dB
VS+
V
= 0V
78
97
dB
= 0V
72
97
dB
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 20mA
15
90
225
70
200
500
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 20mA
20
130
450
80
260
850
mV
mV
mV
ISC
Short-Circuit Current
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
Frequency = 2MHz
70
MHz
FPBW
Full Power Bandwidth
VO = 8VP-P
0.9
MHz
SR
Slew Rate
AV = – 1, RL = 1k, VO = ±4V, Measured at VO = ±2V
20
V/µs
HD
Harmonic Distortion
AV = 1, RL = 1k, VO = 2VP-P, fC = 500kHz
–75
dBc
tS
Settling Time
0.01%, VSTEP = 5V, AV = 1V, RL = 1k
300
ns
25
50
1.8
mA
3
mA
∆G
Differential Gain (NTSC)
AV = 2, RL = 150Ω
0.35
%
∆θ
Differential Phase (NTSC)
AV = 2, RL = 150Ω
0.2
Deg
18012fb
6
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the temperature range of
0°C < TA < 70°C. VS = ±5V, VCM = 0V, VOUT = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
–
TYP
MAX
UNITS
200
220
290
0.75
800
1000
1300
4
µV
µV
µV
mV
VOS
Input Offset Voltage
VCM = VS
VCM = VS– (MS8)
VCM = VS– (DD)
VCM = VS+
●
●
●
●
∆VOS
Input Offset Shift
VCM = VS– to VS+ – 1.5V
●
45
675
µV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = VS–
VCM = VS– (MS8)
VCM = VS– (DD)
●
●
●
240
300
340
1500
1700
1950
µV
µV
µV
●
1.5
5
VOS TC
Input Offset Voltage Drift (Note 8)
–
µV/°C
Input Bias Current
VCM = VS + 1V
VCM = VS+ – 0.2V
●
●
30
450
300
2000
nA
nA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = VS– + 1V
VCM = VS+ – 0.2V
●
●
25
25
400
700
nA
nA
IOS
Input Offset Current
VCM = VS– + 1V
VCM = VS+ – 0.2V
●
●
25
25
300
300
nA
nA
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –2V to 2V, RL = 100Ω
●
●
15
2
55
5
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VCM = VS– to 3.5V
●
82
105
dB
CMRR Match (Channel-to-Channel) (Note 9)
VCM = VS– to 3.5V
●
76
105
●
VS
–
= 0V
●
74
91
dB
= 0V
●
68
93
dB
IB
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
VS+
VS+
= 2.5V to 10V, VS–
= 2.5V to 10V, VS–
dB
VS
+
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 20mA
●
●
●
17
105
250
80
250
575
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 20mA
●
●
●
25
150
600
90
310
975
mV
mV
mV
ISC
Short-Circuit Current
●
IS
Supply Current per Amplifier
●
2.4
22.5
45
mA
4
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz
●
70
MHz
SR
Slew Rate
AV = – 1, RL = 1k, VO = ±4V,
Measured at VO = ±2V
●
20
V/µs
The ● denotes the specifications which apply over the temperature range of – 40°C < TA < 85°C. VS = ±5V, VCM = 0V, VOUT = 0V, unless
otherwise noted. (Note 5)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = VS
VCM = VS– (MS8)
VCM = VS– (DD)
VCM = VS+
●
●
●
●
350
350
350
0.75
1000
1200
1500
5
µV
µV
µV
mV
∆VOS
Input Offset Shift
VCM = VS– to VS+ – 1.5V
●
50
750
µV
●
●
●
280
380
410
1700
1900
2100
µV
µV
µV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
–
–
VCM = VS
VCM = VS– (MS8)
VCM = VS– (DD)
18012fb
7
LT1801/LT1802
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the temperature range
of – 40°C < TA < 85°C. VS = ±5V, VCM = 0V, VOUT = 0V, unless otherwise noted. (Note 5)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
µV/°C
VOS TC
Input Offset Voltage Drift (Note 8)
●
1.5
5
IB
Input Bias Current
VCM = VS– + 1V
VCM = VS+ – 0.2V
●
●
50
450
400
2250
nA
nA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = VS– + 1V
VCM = VS+ – 0.2V
●
●
25
25
450
700
nA
nA
IOS
Input Offset Current
VCM = VS– + 1V
VCM = VS+ – 0.2V
●
●
25
25
350
350
nA
nA
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –1V to 1V, RL = 100Ω
●
●
12.5
2
55
5
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VCM = VS– to 3.5V
●
81
104
dB
– to 3.5V
●
75
104
●
VS–
= 0V
●
73
= 0V
●
67
CMRR Match (Channel-to-Channel) (Note 9)
VCM = VS
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
VS+
VS+
= 2.5V to 10V, VS–
= 2.5V to 10V, VS–
dB
VS+
90
V
dB
90
dB
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 10mA
●
●
●
20
110
180
100
275
400
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 10mA
●
●
●
30
150
300
110
350
700
mV
mV
mV
ISC
Short-Circuit Current
●
IS
Supply Current per Amplifier
●
2.6
4.5
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz
●
65
MHz
SR
Slew Rate
AV = – 1, RL = 1k, VO = ±4V,
Measured at VO = ±2V
●
15
V/µs
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: The inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 1.4V, the input current should be limited to less than
10mA.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The LT1801C/LT1801I and LT1802C/LT1802I are guaranteed
functional over the temperature range of – 40°C to 85°C.
Note 5: The LT1801C/LT1802C are guaranteed to meet specified
performance from 0°C to 70°C. The LT1801C/LT1802C are designed,
characterized and expected to meet specified performance from
–40°C to 85°C but are not tested or QA sampled at these temperatures.
The LT1801I/LT1802I are guaranteed to meet specified performance from
–40°C to 85°C.
12.5
30
mA
Note 6: Minimum supply voltage is guaranteed by power supply rejection
ratio test.
Note 7: Output voltage swings are measured between the output and
power supply rails.
Note 8: This parameter is not 100% tested.
Note 9: Matching parameters are the difference between amplifiers A
and D and between B and C on the LT1802; between the two amplifiers
on the LT1801.
Note 10: Thermal resistance (θJA) varies with the amount of PC board
metal connected to the package. The specified values are for short traces
connected to the leads. If desired, the thermal resistance can be
substantially reduced by connecting Pin 4 of the SO-8 and MS8, Pin 11 of
the SO-14 or the underside metal of the DD package to a larger metal area
(VS– trace).
18012fb
8
LT1801/LT1802
U W
TYPICAL PERFOR A CE CHARACTERISTICS
VOS Distribution, VCM = 0V
(PNP Stage)
VS = 5V, 0V
VCM = 0V
25
20
15
10
Supply Current vs Supply Voltage
4
VS = 5V, 0V
VCM = 5V
40
PERCENT OF UNITS (%)
30
PERCENT OF UNITS (%)
45
35
SUPPLY CURRENT (mA)
35
VOS Distribution, VCM = 5V
(NPN Stage)
30
25
20
15
10
5
–150
–50
50
150
INPUT OFFSET VOLTAGE (µV)
0
–2000
250
–1200
–400
400
1200
INPUT OFFSET VOLTAGE (µV)
18012 G01
TA = 25°C
2
TA = –55°C
1
Input Bias Current
vs Common Mode Voltage
1.0
VS = 5V, 0V
TYPICAL PART
TA = –55°C
400
INPUT BIAS CURRENT (µA)
200
TA = 25°C
0
–100
–200
TA = 125°C
–300
–400
1
3
4
2
INPUT COMMON MODE VOLTAGE (V)
0.6
0.6
0.4
0.2
0
–0.2
–0.4
5
–0.6
–1.0
–1
0
2
3
4
5
1
INPUT COMMON MODE VOLTAGE (V)
OUTPUT SATURATION VOLTAGE (V)
OUTPUT SATURATION VOLTAGE (V)
0.2
PNP ACTIVE
VS = 5V, 0V
VCM = 1V
–0.1
20
–60 –40 –20 0
40
TEMPERATURE (°C)
6
60
80
18012 G06
Output Saturation Voltage
vs Load Current (Output High)
10
0.1
TA = 125°C
TA = 25°C
1
10
0.1
LOAD CURRENT (mA)
0.3
18012 G05
1
0.001
0.01
NPN ACTIVE
VS = 5V, 0V
VCM = 5V
0.4
0
VS = 5V, 0V
TA = –55°C
0.5
0.1
Output Saturation Voltage
vs Load Current (Output Low)
0.01
3 4 5 6 7 8 9 10 11 12
TOTAL SUPPLY VOLTAGE (V)
0.8
18012 G04
10
2
0.7
–0.8
0
1
Input Bias Current
vs Temperature
VS = 5V, 0V
TA = 25°C
TA = 125°C
TA = –55°C
0.8
300
100
0
18012 G03
INPUT BIAS (µA)
500
0
2000
18012 G02
Offset Voltage
vs Input Common Mode Voltage
OFFSET VOLTAGE (µV)
TA = 125°C
3
5
0
–250
–500
PER AMPLIFIER
100
18012 G07
VS = 5V, 0V
1
0.1
TA = 125°C
0.01
TA = –55°C
0.001
0.01
TA = 25°C
1
10
0.1
LOAD CURRENT (mA)
100
18012 G08
18012fb
9
LT1801/LT1802
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Short-Circuit Current
vs Power Supply Voltage
OUTPUT SHORT-CIRCUIT CURRENT (mA)
TA = –55°C
0.4
0.2
TA = 25°C
0
–0.2
TA = 125°C
–0.4
–0.6
0
1.5
2 2.5 3 3.5 4 4.5
TOTAL SUPPLY VOLTAGE (V)
5
70
60
50
40
30
20
10
0
–10
–20
–30
–40
–50
–60
–70
TA = 25°C
TA = 125°C
TA = –55°C
SINKING
TA = –55°C
SOURCING
TA = 125°C
2
4
2.5
4.5
3.5
3
POWER SUPPLY VOLTAGE (±V)
CHANGE IN OFFSET VOLTAGE (µV)
CHANGE IN OFFSET VOLTAGE (µV)
800
400
RL = 1k
0
–400
RL = 100Ω
1
1.5 2 2.5 3 3.5 4
OUTPUT VOLTAGE (V)
4.5
–1200
2.0
1200
800
400
RL = 1k
0
–400
–800
RL = 100Ω
–2000
5
–5 –4 –3 –2 –1 0 1 2 3
OUTPUT VOLTAGE (V)
Warm-Up Drift vs Time
4
NOISE VOLTAGE (nV/√Hz)
90
VS = ±2.5V
70
VS = ±1.5V
1.0
TYPICAL PART
20
40
TA = –55°C
0.5
0
–0.5 TA = 25°C
TA = 125°C
–1.0
–1.5
–2.0
15 30
–60 –45 –30 –15 0
OUTPUT CURRENT (mA)
5
45
60
18012 G14
VS = 5V, 0V
40
80 100 120
60
TIME AFTER POWER-UP (SECONDS)
140
18012 G15
NPN ACTIVE
VCM = 4.25V
30
20
10
50
0
VS = ±5V
50
100
40
3
Input Noise Voltage vs Frequency
VS = ±5V
60
2.5
1.5
60
80
1.5
2
1
OUTPUT VOLTAGE (V)
18012 G13
120
110
0.5
18012 G11
VS = ±5V
RL TO GND
1600
18012 G12
OFFSET VOLTAGE (µV)
RL = 100Ω
0
–1600
0.5
–400
–800
5
–1200
–1600
0
RL = 1k
0
Offset Voltage vs Output Current
2000
VS = 5V, 0V
RL TO GND
1200
–2000
400
Open-Loop Gain
1600
–1200
800
18012 G10
Open-Loop Gain
–800
1200
–2000
18012 G09
2000
VS = 3V, 0V
RL TO GND
1600
–1600
TA = 25°C
1.5
5.5
Open-Loop Gain
2000
CHANGE IN OFFSET VOLTAGE (mV)
CHANGE IN OFFSET VOLTAGE (mV)
0.6
CHANGE IN OFFSET VOLTAGE (µV)
Minimum Supply Voltage
PNP ACTIVE
VCM = 2.5V
0
0.01
0.1
1
10
FREQUENCY (kHz)
100
18012 G16
18012fb
10
LT1801/LT1802
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Input Current Noise vs Frequency
3.0
Gain Bandwidth and Phase
Margin vs Supply Voltage
0.1Hz to 10Hz Input Voltage Noise
2000
VS = 5V, 0V
100
VS = 5V, 0V
PNP ACTIVE
VCM = 2.5V
1.5
1.0
NPN ACTIVE
VCM = 4.25V
0
0.01
0.1
1000
GAIN BANDWIDTH (MHz)
INPUT NOISE VOLTAGE (nV)
2.0
0
–1000
1
10
FREQUENCY (kHz)
50
40
1
2
3
4 5 6 7
TIME (SECONDS)
8
9
10
50
40
SLEW RATE (V/µs)
60
30
AV = –1
RF = RG = 1k
RL = 1k
VS = ±2.5V
VS = ±5V
25
10
5 25 45 65 85 105 125
TEMPERATURE (°C)
20
70
100
60
80
50
60
40
40
20
30
GAIN
20
0
10
–20
0
–40
–60
–10
15
–20
10
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
–30
0.01
VS = ±2.5V
VS = ±5V
0.1
–80
1
10
FREQUENCY (MHz)
–100
100 300
18012 G22
18012 G21
18012 G20
Gain vs Frequency (AV = 2)
Gain vs Frequency (AV = 1)
12
18
6
12
RL = 1k
15 CL = 10pF
AV = 2
VS = ±2.5V
3
VS = ±5V
–3
GAIN (dB)
RL = 1k
9 CL = 10pF
AV = 1
GAIN (dB)
10
PHASE
20
9
6
VS = ±2.5V
3
VS = ±5V
–6
0
–9
–3
–12
0.1
9
PHASE (DEG)
60
PHASE MARGIN (DEG)
GBW PRODUCT
VS = ±5V
PHASE MARGIN
VS = ±5V
2 3 4 5 6 7 8
TOTAL SUPPLY VOLTAGE (V)
Gain and Phase vs Frequency
OPEN-LOOP GAIN (dB)
30
80
PHASE MARGIN
VS = ±2.5V
1
18012 G19
Slew Rate vs Temperature
GBW PRODUCT
VS = ±2.5V
0
0
18012 G18
35
90
GAIN BANDWIDTH (MHz)
60
PHASE MARGIN
20
0
100
–55 –35 –15
60
–2000
100
Gain Bandwidth and Phase
Margin vs Temperature
50
70
30
18012 G17
70
GAIN BANDWIDTH
PRODUCT
80
PHASE MARGIN (DEG)
NOISE CURRENT (pA/√Hz)
2.5
0.5
TA = 25°C
90
1
10
FREQUENCY (MHz)
100
300
18012 G23
–6
0.1
10
1
FREQUENCY (MHz)
100
300
18012 G24
18012fb
11
LT1801/LT1802
U W
TYPICAL PERFOR A CE CHARACTERISTICS
AV = 10
10
AV = 1
1
AV = 2
0.1
0.01
0.001
0.1
1
10
FREQUENCY (MHz)
100
100
80
60
40
20
0
0.01
500
0.1
1
10
FREQUENCY (MHz)
100
18012 G25
50
60
50
OVERSHOOT (%)
OVERSHOOT (%)
40
35
30
ROS = 20Ω
25
20
15
35
30
ROS = 10Ω
25
20
ROS = 20Ω
100
1000
CAPACITIVE LOAD (pF)
10000
ROS = RL = 50Ω
0
100
1000
CAPACITIVE LOAD (pF)
10
18012 G28
–60
RL = 150Ω, 2ND
RL = 1k,
2ND
–80
–90
–100
RL = 1k, 3RD
VS = 5V, 0V
AV = 1
VOUT = 2VP-P
–60
RL = 150Ω, 2ND
–70
RL = 1k, 2ND
RL = 150Ω, 3RD
–80
–90
RL = 1k, 3RD
0.1
1
FREQUENCY (MHz)
10
18012 G30
4.5
4.4
AV = 2
4.3
AV = –1
4.2
4.1
4.0
VS = 5V, 0V
RL = 1k
3.9
0.1
1
FREQUENCY (MHz)
100
4.6
RL = 150Ω,
3RD
–70
10
Maximum Undistorted Output
Signal vs Frequency
VS = 5V, 0V
AV = 2
VOUT = 2VP-P
–110
0.01
0.1
1
FREQUENCY (MHz)
18012 G29
OUTPUT VOLTAGE SWING (VP-P)
DISTORTION (dBc)
–50
0.01
–110
0.01
10000
Distortion vs Frequency
–40
0
–100
5
0
10
20
10
–50
10
ROS = RL = 50Ω
5
40
30
Distortion vs Frequency
40
15
10
50
–40
45
ROS = 10Ω
POSITIVE
SUPPLY
18012 G27
VS = 5V, 0V
AV = 2
55
45
NEGATIVE
SUPPLY
60
Series Output Resistor
vs Capacitive Load
VS = 5V, 0V
AV = 1
55
70
18012 G26
Series Output Resistor
vs Capacitive Load
60
VS = 5V, 0V
TA = 25°C
80
–10
0.001
DISTORTION (dBc)
OUTPUT IMPEDANCE (Ω)
100
90
VS = 5V, 0V
POWER SUPPLY REJECTION RATIO (dB)
120
VS = ±2.5V
COMMON MODE REJECTION RATIO (dB)
600
Power Supply Rejection Ratio
vs Frequency
Common Mode Rejection Ratio
vs Frequency
Output Impedance vs Frequency
10
18012 G31
1k
10k
100k
1M
FREQUENCY (Hz)
10M
18012 G32
18012fb
12
LT1801/LT1802
U W
TYPICAL PERFOR A CE CHARACTERISTICS
5V Small-Signal Response
5V Large-Signal Response
50mV/DIV
0V
1V/DIV
0V
VS = 5V, 0V
AV = 1
RL = 1k
100ns/DIV
VS = 5V, 0V
AV = 1
RL = 1k
18012 G33
2V/DIV
50mV/DIV
0V
0V
200ns/DIV
18012 G34
±5V Small-Signal Response
±5V Large-Signal Response
VS = ±5V
AV = 1
RL = 1k
50ns/DIV
VS = ±5V
AV = 1
RL = 1k
18012 G35
50ns/DIV
18012 G36
Output Overdriven Recovery
VIN
1V/DIV
0V
VOUT
2V/DIV
VS = 5V, 0V
AV = 2
RL = 1k
100ns/DIV
18012 G37
18012fb
13
LT1801/LT1802
U
W
U U
APPLICATIO S I FOR ATIO
A pair of complementary common emitter stages Q14/
Q15 that enable the output to swing from rail to rail
constructs the output stage. The capacitors C2 and C3
form the local feedback loops that lower the output impedance at high frequency. These devices are fabricated on
Linear Technology’s proprietary high speed complementary bipolar process.
Circuit Description
The LT1801/LT1802 have an input and output signal range
that covers from the negative power supply to the positive
power supply. Figure 1 depicts a simplified schematic of
the amplifier. The input stage is comprised of two differential amplifiers, a PNP stage Q1/Q2 and an NPN stage Q3/
Q4 that are active over the different ranges of common
mode input voltage. The PNP differential pair is active
between the negative supply to approximately 1.2V below
the positive supply. As the input voltage moves closer
toward the positive supply, the transistor Q5 will steer the
tail current I1 to the current mirror Q6/Q7, activating the
NPN differential pair and the PNP pair becomes inactive
for the rest of the input common mode range up to the
positive supply. Also at the input stage, devices Q17 to
Q19 act to cancel the bias current of the PNP input pair.
When Q1-Q2 are active, the current in Q16 is controlled to
be the same as the current in Q1-Q2, thus the base current
of Q16 is nominally equal to the base current of the input
devices. The base current of Q16 is then mirrored by
devices Q17-Q19 to cancel the base current of the input
devices Q1-Q2.
Power Dissipation
The LT1801 amplifier is offered in a small package, SO-8,
which has a thermal resistance of 190°C/W, θJA. So there
is a need to ensure that the die’s junction temperature
should not exceed 150°C. Junction temperature TJ is
calculated from the ambient temperature TA, power dissipation PD and thermal resistance θJA:
TJ = TA + (PD • θJA)
The power dissipation in the IC is the function of the supply
voltage, output voltage and the load resistance. For a given
supply voltage, the worst-case power dissipation PDMAX
occurs at the maximum supply current and the output
V+
R3
V+
+
R5
V–
ESDD1
I2
R4
+
D1
ESDD2
Q12
Q11
I1
Q13
+IN
D6
D8
D5
D7
–IN
D2
Q5
I3
OUT
CC
D3
BUFFER
AND
OUTPUT BIAS
Q10
V+
D4
Q9
Q16
Q17
Q18
V–
Q1 Q2
ESDD3
V–
+
VBIAS
Q4 Q3
ESDD4
Q15
C2
Q8
C1
Q19
Q7
Q14
Q6
R1
V–
R2
18012 F01
Figure 1. LT1801/LT1802 Simplified Schematic Diagram
18012fb
14
LT1801/LT1802
U
W
U U
APPLICATIO S I FOR ATIO
voltage is at half of either supply voltage (or the maximum
swing is less than 1/2 supply voltage). PDMAX is given by:
PDMAX = (VS • ISMAX) + (VS/2)2/RL
Example: An LT1801 in an SO-8 package operating on ±5V
supplies and driving a 50Ω load, the worst-case power
dissipation is given by:
PDMAX = (10 • 4.5mA) + (2.5)2/50 = 0.045 + 0.125
= 0.17W
If both amplifiers are loaded simultaneously, then the total
power dissipation is 0.34W.
The maximum ambient temperature that the part is allowed to operate is:
TA = TJ – (PDMAX • 190°C/W)
= 150°C – (0.34W • 190°C/W) = 85°C
Input Offset Voltage
The offset voltage will change depending upon which input
stage is active. The PNP input stage is active from the
negative supply rail to 1.2V from the positive supply rail,
then the NPN input stage is activated for the remaining input
range up to the positive supply rail during which the PNP
stage remains inactive. The offset voltage is typically less
than 75µV in the range that the PNP input stage is active.
Input Bias Current
The LT1801/LT1802 employ a patent-pending technique
to trim the input bias current to less than 250nA for the
input common mode voltage of 0.2V above negative
supply rail to 1.2V of the positive rail. The low input offset
voltage and low input bias current of the LT1801/LT1802
provide precision performance especially for high source
impedance applications.
Output
The LT1801/LT1802 can deliver a large output current, so
the short-circuit current limit is set around 50mA to
prevent damage to the device. Attention must be paid to
keep the junction temperature of the IC below the absolute
maximum rating of 150°C (refer to the Power Dissipation
section) when the output is continuously short circuited.
The output of the amplifier has reverse-biased diodes
connected to each supply. If the output is forced beyond
either supply, unlimited current will flow through these
diodes. If the current is transient and limited to several
hundred mA and the total supply voltage is less than
12.6V, the absolute maximum rating, no damage will
occur to the device.
Overdrive Protection
When the input voltage exceeds the power supplies, two
pairs of crossing diodes D1 to D4 will prevent the output
from reversing polarity. If the input voltage exceeds either
power supply by 700mV, diode D1/D2 or D3/D4 will turn
on to keep the output at the proper polarity. For the phase
reversal protection to perform properly, the input current
must be limited to less than 10mA. If the amplifier is
severely overdriven, an external resistor should be used to
limit the overdrive current.
The LT1801/LT1802’s input stages are also protected
against a large differential input voltage of 1.4V or higher
by a pair of back-back diodes D5/D8 to prevent the emitterbase breakdown of the input transistors. The current in these
diodes should be limited to less than 10mA when they are
active. The worst-case differential input voltage usually
occurs when the input is driven while the output is shorted
to ground in a unity gain configuration. In addition, the
amplifier is protected against ESD strikes up to 3kV on all
pins by a pair of protection diodes on each pin that are
connected to the power supplies as shown in Figure 1.
18012fb
15
LT1801/LT1802
U
W
U U
APPLICATIO S I FOR ATIO
Capacitive Load
Feedback Components
The LT1801/LT1802 are optimized for high bandwidth,
low power and precision applications. They can drive a
capacitive load of about 75pF in a unity-gain configuration,
and more for higher gain. When driving a larger capacitive
load, a resistor of 10Ω to 50Ω should be connected
between the output and the capacitive load to avoid ringing
or oscillation. The feedback should still be taken from the
output so that the resistor will isolate the capacitive load
to ensure stability. Graphs on capacitive loads indicate the
transient response of the amplifier when driving capacitive
load with a specified series resistor.
When feedback resistors are used to set up gain, care must
be taken to ensure that the pole formed by the feedback
resistors and the total capacitance at the inverting input
does not degrade stability. For instance, the LT1801/
LT1802 in a noninverting gain of 2, setup with two 5k
resistors and a capacitance of 5pF (part plus PC board) will
probably oscillate. The pole is formed at 12.7MHz that will
reduce phase margin by 57 degrees when the crossover
frequency of the amplifier is around 20MHz. A capacitor of
5pF or higher connected across the feedback resistor will
eliminate any ringing or oscillation.
U
TYPICAL APPLICATIO S
Single 3V Supply, 1MHz, 4th Order Butterworth Filter
Fast 1A Current Sense Amplifier
The circuit shown on the first page of this data sheet makes
use of the low voltage operation and the wide bandwidth
of the LT1801 to create a DC accurate 1MHz 4th order
lowpass filter powered from a 3V supply. The amplifiers
are configured in the inverting mode for the lowest distortion and the output can swing rail-to-rail for maximum
dynamic range. Also on the first page of this data sheet, the
graph displays the frequency response of the filter.
Stopband attenuation is greater than 100dB at 50MHz.
With a 2.25VP-P, 250kHz input signal, the filter has harmonic distortion products of less than – 85dBc. Worst
case output offset voltage is less than 6mV.
A simple, fast current sense amplifier in Figure 2 is suitable
for quickly responding to out-of-range currents. The circuit amplifies the voltage across the 0.1Ω sense resistor
by a gain of 20, resulting in a conversion gain of 2V/A. The
–3dB bandwidth of the circuit is 4MHz, and the uncertainty
due to VOS and IB is less than 4mA. The minimum output
voltage is 60mV, corresponding to 30mA. The large-signal
response of the circuit is shown in Figure 3.
IL
0A TO 1A
52.3Ω
3V
+
VOUT
0V TO 2V
1/2 LT1801
–
0.1Ω
52.3Ω
500mV/DIV
1k
0V
18012 F02
VOUT = 2 • IL
f–3dB = 4MHz
UNCERTAINTY DUE TO VOS, IB < 4mA
Figure 2. Fast 1A Current Sense
VS = 3V
50ns/DIV
18012 F03
Figure 3. Current Sense Amplifier Large-Signal Response
18012fb
16
LT1801/LT1802
U
TYPICAL APPLICATIO S
Single Supply 1A Laser Driver Amplifier
Figure 4 shows the LT1801 used in a 1A laser driver
application. One of the reasons the LT1801 is well suited
to this control task is that its 2.3V operation ensures that
it will be awaked during power-up and operated before the
circuit can otherwise cause significant current to flow in
the 2.1V threshold laser diode. Driving the noninverting
input of the LT1801 to a voltage VIN will control the turning
on of the high current NPN transistor, FMMT619 and the
laser diode. A current equal to VIN/R1 flows through the
laser diode. The LT1801 low offset voltage and low input
bias current allows it to control the current that flows
through the laser diode precisely. The overall circuit is a 1A
per volt V-to-I converter. Frequency compensation components R2 and C1 are selected for fast but zero-overshoot time domain response to avoid overcurrent conditions in the laser. The time domain response of this circuit,
measured at R1 and given a 500mV 230ns input pulse, is
shown in Figure 5. While the circuit is capable of 1A
operation, the laser diode and the transistor are thermally
limited due to power dissipation, so they must be operated
at low duty cycles.
5V
VIN
DO NOT FLOAT
+
R3
10Ω
Q1
ZETEX
FMMT619
1/2 LT1801
–
C1
39pF
IR LASER
INFINEON
SFH495
R2
330Ω
R1
1Ω
18012 F04
Figure 4. Single Supply 1A Laser Driver Amplifier
100mA/DIV
50ns/DIV
18012 F05
Figure 5. 500mA Pulse Response
18012fb
17
LT1801/LT1802
U
PACKAGE DESCRIPTIO
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
R = 0.115
TYP
5
0.38 ± 0.10
8
0.675 ±0.05
3.5 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
1.65 ± 0.10
(2 SIDES)
3.00 ±0.10
(4 SIDES)
PIN 1
PACKAGE TOP MARK
(NOTE
6)
OUTLINE
(DD) DFN 1203
0.25 ± 0.05
4
0.25 ± 0.05
0.75 ±0.05
0.200 REF
0.50
BSC
2.38 ±0.05
(2 SIDES)
1
0.50 BSC
2.38 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
3.2 – 3.45
(.126 – .136)
0.42 ± 0.04
(.0165 ± .0015)
TYP
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.65
(.0256)
BSC
8
7 6 5
0.52
(.206)
REF
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 ± 0.102
(.118 ± .004)
NOTE 4
4.90 ± 0.15
(1.93 ± .006)
DETAIL “A”
0° – 6° TYP
GAUGE PLANE
0.53 ± 0.015
(.021 ± .006)
DETAIL “A”
1
2 3
4
1.10
(.043)
MAX
0.86
(.034)
REF
0.18
(.077)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
BSC
0.13 ± 0.076
(.005 ± .003)
MSOP (MS8) 0802
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
18012fb
18
LT1801/LT1802
U
PACKAGE DESCRIPTIO
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
7
8
.245
MIN
5
6
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
3
2
4
.053 – .069
(1.346 – 1.752)
.008 – .010
(0.203 – 0.254)
.004 – .010
(0.101 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
.050
(1.270)
BSC
.014 – .019
(0.355 – 0.483)
TYP
NOTE:
1. DIMENSIONS IN
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
SO8 0303
S Package
14-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.337 – .344
(8.560 – 8.738)
NOTE 3
.045 ±.005
.050 BSC
14
N
12
11
10
9
8
N
.245
MIN
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
1
.030 ±.005
TYP
13
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
1
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
2
3
4
5
6
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.014 – .019
(0.355 – 0.483)
TYP
7
.050
(1.270)
BSC
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
S14 0502
18012fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1801/LT1802
U
TYPICAL APPLICATIO
Low Power High Voltage Amplifier
Certain materials used in optical applications have characteristics that change due to the presence and strength of
a DC electric field. The voltage applied across these
materials should be precisely controlled to maintain desired properties, sometimes as high as 100’s of volts. The
materials are not conductive and represent a capacitive
load.
The circuit of Figure 6 shows the LT1801 used in an
amplifier capable of a 250V output swing and providing
130V
5V
4.99k
10k
1k
Q5
Q6
0.1µF
5V
Q2
Q1
+
R2
2k
precise DC output voltage. When no signal is present, the
op amp output sits at about mid-supply. Transistors Q1
and Q3 create bias voltages for Q2 and Q4, which are
forced into a low quiescent current by degeneration resistors R4 and R5. When a transient signal arrives at VIN, the
op amp output moves and causes the current in Q2 or Q4
to change depending on the signal polarity. The current,
limited by the clipping of the LT1801 output and the 3kΩ
of total emitter degeneration, is mirrored to the output
devices to drive the capacitive load. The LT1801 output
then returns to near mid-supply, providing the precise DC
output voltage to the load. The attention to limit the current
of the output devices minimizes power dissipation thus
allowing for dense layout, and inherits better reliability.
Figure 7 shows the time domain response of the amplifier
providing a 200V output swing into a 100pF load.
5V
R4
2k
R6
2k
R5
2k
R7
2k
VOUT
1/2 LT1801
–
Q3
MATERIAL UNDER
ELECTRIC FIELD
100pF
Q4
VIN
R1
2k
C2
8pF
150V
C1
39pF
R3
200k
VIN
2V/DIV
10k
Q8
Q7
4.99k
1k
–130V
AV = VOUT/VIN = –100
±130V SUPPLY IQ = 130µA
OUTPUT SWING = ±128.8V
OUTPUT OFFSET ≅ 20mV
OUTPUT SHORT-CIRCUIT CURRENT ≅ 3mA
10% TO 90% RISE TIME ≅ 8µs, 200V OUTPUT STEP
SMALL-SIGNAL BANDWIDTH ≅ 150kHz
Q1, Q2, Q7, Q8: ON SEMI MPSA42
Q3, Q4, Q5, Q6: ON SEMI MPSA92
VOUT
50V/DIV
10µs/DIV
18012 F07
18012 F06
Figure 6. Low Power, High Voltage Amplifier
Figure 7. Large-Signal Time Domain
Response of the Amplifier
RELATED PARTS
PART NUMBER
LT1399
LT1498/LT1499
LT1630/LT1631
DESCRIPTION
Triple 300MHz Current Feedback Amplifier
Dual/Quad 10MHz, 6V/µs Rail-to-Rail Input and Output C-LoadTM Op Amps
Dual/Quad 30MHz, 10V/µs Rail-to-Rail Input and Output Op Amps
LT1800
LT1806/LT1807
80MHz, 25V/µs Low Power Rail-to-Rail Input/Output Precision Op Amp
Single/Dual 325MHz, 140V/µs Rail-to-Rail Input and Output Op Amps
LT1809/LT1810
Single/Dual 180MHz Rail-to-Rail Input/Output Op Amps
COMMENTS
0.1dB Gain Flatness to 150MHz, Shutdown
High DC Accuracy, 475µV VOS(MAX), 4µV/°C Max Drift
High DC Accuracy, 525µV VOS(MAX), 70mA Output Current,
Max Supply Current 4.4mA per Amplifier
Single Version of LT1801/LT1802
High DC Accuracy, 550µV VOS(MAX), Low Noise 3.5nV/√Hz,
Low Distortion –80dB at 5MHz, Power-Down (LT1806)
350V/µs Slew Rate, Low Distortion –90dBc at 5MHz,
Power-Down (LT1809)
C-Load is a trademark of Linear Technology Corporation.
18012fb
20
Linear Technology Corporation
LT 0607 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2002