LINER LT1804CDD

LT1803/LT1804/LT1805
Single/Dual/Quad 100V/µs,
85MHz, Rail-to-Rail Input and
Output Op Amps
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
Slew Rate: 100V/µs
Gain Bandwidth Product: 85MHz
Input Common Mode Range Includes Both Rails
Output Swings Rail-to-Rail
Low Quiescent Current: 3mA Max per Amplifier
Large Output Current: 42mA
Voltage Noise: 21nV/√Hz
Power Supply Rejection: 90dB
Open-Loop Gain: 60V/mV
Operating Temperature Range: – 40°C to 85°C
Single Available in the 8-Pin SO and 5-Pin Low Profile
(1mm) SOT-23 (ThinSOTTM) Package
Dual Available in 8-Lead DFN and SO Packages
Quad Available in the 14-Pin Narrow SO Package
U
APPLICATIO S
■
■
■
■
■
Low Voltage, High Frequency Signal Processing
Driving A/D Converters
Rail-to-Rail Buffer Amplifiers
Active Filters
Video Line Driver
, LTC and LT are registered trademarks of Linear Technology Corporation.
ThinSOT is a trademark of Linear Technology Corporation.
The LT®1803/LT1804/LT1805 are single/dual/quad, low
power, high speed rail-to-rail input and output operational
amplifiers with excellent DC performance. The LT1803/
LT1804/LT1805 feature reduced supply current, lower
input offset voltage, lower input bias current and higher
DC gain than other devices with comparable bandwidth
and slew rate.
Typically, the LT1803/LT1804/LT1805 have an input offset voltage of 350µV, an input bias current of 125nA and
an open-loop gain of 60V/mV.
The LT1803/LT1804/LT1805 have an input range that
includes both supply rails and an output that swings within
20mV of either supply rail to maximize the signal dynamic
range in low supply applications.
The LT1803/LT1804/LT1805 are specified at 3V, 5V and
±5V supplies and typically maintain their performance for
supplies from 2.3V to 12.6V. The inputs can be driven
beyond the supplies without damage or phase reversal of
the output.
The LT1803 is available in the 8-pin SO package with the
standard op amp pinout and in the 5-pin SOT-23 package.
The LT1804 is available in 8-pin DFN and SO packages
with the standard op amp pinouts. The LT1805 features
the standard quad op amp configuration and is available in
a 14-pin plastic SO package.
U
TYPICAL APPLICATIO
Inverting DC Restore Circuit Response
Inverting DC Restore
R2
10k
R1
1k
VIN
VIN
50mV/DIV
GND
–
A
1/2 LT1804
VOUT
+
VS+
R4
100k
R5
2k
R6
1M
VS = ±5V
B
1/2 LT1804
+
C1
0.1µF
D1
1N4148
–
D2
1N4148
R3
1k
VOUT
500mV/DIV
GND
50µs/DIV
18045 TA02
18045 TA01
VS–
180345f
1
LT1803/LT1804/LT1805
W W
U
W
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Total Supply Voltage (V+ to V–) ........................... 12.6V
Input Current (Note 2) ....................................... ±10mA
Output Short-Circuit Duration (Note 3) ........... Indefinite
Operating Temperature Range (Note 4) .. – 40°C to 85°C
Specified Temperature Range (Note 5) ... – 40°C to 85°C
Maximum Junction Temperature ......................... 150°C
Maximum Junction Temperature (DD Package) .. 125°C
Storage Temperature Range ................. – 65°C to 150°C
Storage Temperature Range
(DD Package) ....................................... – 65°C to 125°C
Lead Temperature (Soldering, 10 sec).................. 300°C
W
U
U
PACKAGE/ORDER INFORMATION
TOP VIEW
TOP VIEW
5 V+
VOUT 1
V
–2
NC 1
–IN 2
+ –
+IN 3
4 –IN
+IN 3
–
+
V– 4
S5 PACKAGE
5-LEAD PLASTIC TSOT-23
TJMAX = 150°C, θJA = 250°C/W
8
NC
7
V+
6
VOUT
5
NC
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 190°C/W
ORDER PART
NUMBER
S5 PART
MARKING*
ORDER PART
NUMBER
S8 PART
MARKING
LT1803CS5
LT1803IS5
LTAFN
LT1803CS8
LT1803IS8
1803
1803I
TOP VIEW
TOP VIEW
OUT A 1
–IN A 2
+IN A 3
V
–
8
7
–
+A
4
–
B+
6
5
V
OUT B
–IN B
+IN B
DD PACKAGE
8-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 160°C/W
UNDERSIDE METAL INTERNALLY CONNECTED TO V –
(PCB CONNECTION OPTIONAL)
ORDER PART
NUMBER
LT1804CDD
LT1804IDD
DD PART
MARKING*
LADJ
OUT A 1
8
–IN A 2
+IN A 3
–
+A
V– 4
V+
7
OUT B
6
–IN B
5
+IN B
–
B+
14 OUT D
OUT A 1
TOP VIEW
+
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 190°C/W
–IN A 2
+IN A 3
V+
–
+A
–
D+
12 +IN D
11 V –
4
+IN B 5
13 –IN D
+
–
B
+
C–
10 +IN C
–IN B 6
9
–IN C
OUT B 7
8
OUT C
S PACKAGE
14-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 160°C/W
ORDER PART
NUMBER
S8 PART
MARKING
ORDER PART
NUMBER
LT1804CS8
LT1804IS8
1804
1804I
LT1805CS
LT1805IS
Consult LTC Marketing for parts specified with wider operating temperature ranges.
*The temperature grades are identified by a label on the shipping container.
180345f
2
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
TA = 25°C; VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted
SYMBOL
PARAMETER
CONDITIONS
TYP
MAX
VOS
Input Offset Voltage
VCM = 0V
VCM = 0V (DD Package)
VCM = 0V (SOT-23 Package)
VCM = VS
0.35
1.00
1.00
1.50
2
3
5
8
mV
mV
mV
mV
∆VOS
Input Offset Shift
VCM = 0V to VS – 2V
0.125
0.50
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = 0V
VCM = 0V (DD Package)
0.5
1.0
3.5
5.0
mV
mV
Input Bias Current
VCM = 1V
VCM = VS
125
3
750
5.5
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = 1V
VCM = VS
100
100
1250
1500
nA
nA
Input Offset Current
VCM = 1V
VCM = VS
100
50
1000
1000
nA
nA
IB
IOS
MIN
UNITS
Input Noise Voltage
0.1Hz to 10Hz
4
µVP-P
en
Input Noise Voltage Density
f = 10kHz
21
nV/√Hz
in
Input Noise Current Density
f = 10kHz
2.5
pA/√Hz
CIN
Input Capacitance
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 0.5V to 4.5V, RL = 1k to VS/2
VS = 5V, VO = 1V to 4V, RL = 100Ω to VS/2
VS = 3V, VO = 0.5V to 2.5V, RL = 1k to VS/2
20
2
15
60
4.5
45
V/mV
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
75
66
96
90
dB
dB
CMRR Match (Channel-to-Channel) (Note 9)
VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
69
60
91
85
dB
dB
2
Input Common Mode Range
PSRR
0␣ ␣
pF
VS
V
Power Supply Rejection Ratio
VS = 2.5V to 10V, VCM = 0V
68
90
dB
PSRR Match (Channel-to-Channel) (Note 9)
VS = 2.5V to 10V, VCM = 0V
62
90
dB
Minimum Supply Voltage (Note 6)
2.3
2.5
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 15mA
17
80
180
60
150
300
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 15mA
17
125
350
60
250
600
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
VS = 5V
VS = 3V
20
18
42
34
2.7
mA
mA
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
VS = 5V, Frequency = 2MHz, RL = 1k to 2.5V
50
85
3
MHz
mA
SR
Slew Rate
VS = 5V, AV = –1, RL = 1k to VS/2, VO = 0.5V to 4.5V
Measured at VO = 1.5V, 3.5V
65
100
V/µs
FPBW
Full Power Bandwidth (Note 10)
VS = 5V, AV = –1, VO = 0.5V to 4.5V, RL = 1k to VS/2
8
MHz
HD
Harmonic Distortion
VS = 5V, AV = 1, RL = 1k, VO = 2VP-P, fC = 1MHz
–75
dBc
tS
Settling Time
0.01%, VS = 5V, VSTEP = 2V, AV = 1, RL = 1k
350
ns
∆G
Differential Gain (NTSC)
VS = 5V, AV = 2, RL = 150Ω
0.15
%
∆θ
Differential Phase (NTSC)
VS = 5V, AV = 2, RL = 150Ω
1
Deg
180345f
3
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the 0°C ≤ TA ≤ 70°C
temperature range. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = 0V
VCM = 0V (DD Package)
VCM = 0V (SOT-23 Package)
VCM = VS
●
●
●
●
MIN
0.50
1.25
1.25
1.60
3.5
5
6
8.5
mV
mV
mV
mV
∆VOS
Input Offset Shift
VCM = 0V to VS – 2V
●
0.05
0.8
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = 0V
VCM = 0V (DD Package)
●
●
0.75
1.50
5.5
7.5
mV
mV
●
10
35
µV/°C
VOS TC
Input Offset Voltage Drift (Note 8)
IB
Input Bias Current
VCM = 1V
VCM = VS – 0.2V
●
●
150
3.2
1100
6
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = 1V
VCM = VS – 0.2V
●
●
120
120
1500
1800
nA
nA
IOS
Input Offset Current
VCM = 1V
VCM = VS – 0.2V
●
●
100
50
1400
1400
nA
nA
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 0.5V to 4.5V, RL = 1k to VS/2
VS = 5V, VO = 1V to 4V, RL = 100Ω to VS/2
VS = 3V, VO = 0.5V to 2.5V, RL=1k to VS/2
●
●
●
15
1.4
10
50
3.7
40
V/mV
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
●
●
71
61
95
90
dB
dB
CMRR Match (Channel-to-Channel) (Note 9) VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
●
●
65
55
90
85
dB
dB
Input Common Mode Range
●
0
PSRR
Power Supply Rejection Ratio
VS = 2.5V to 10V, VCM = 0V
●
65
PSRR Match (Channel-to-Channel) (Note 9)
VS = 2.5V to 10V, VCM = 0V
●
59
Minimum Supply Voltage (Note 6)
VS
87
V
dB
87
dB
●
2.3
2.5
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 15mA
●
●
●
19
100
200
80
225
450
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 15mA
●
●
●
19
150
450
80
350
900
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
VS = 5V
VS = 3V
●
●
17
15
40
28
3
mA
mA
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
VS = 5V, Frequency = 2MHz, RL = 1k to 2.5V
●
45
82
MHz
SR
Slew Rate
VS = 5V, AV = –1, RL = 1k to VS/2, VO = 0.5V to 4.5V
Measured at VO = 1.5V, 3.5V
●
45
93
V/µs
●
3.75
mA
180345f
4
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the –40°C ≤ TA ≤ 85°C
temperature range. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply unless otherwise noted. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = 0V
VCM = 0V (DD Package)
VCM = 0V (SOT-23 Package)
VCM = VS
●
●
●
●
MIN
0.7
1.5
1.5
1.7
4
6.5
7
9
mV
mV
mV
mV
∆VOS
Input Offset Shift
VCM = 0V to VS – 2V
●
0.125
1.00
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = 0V
VCM = 0V (DD Package)
●
●
1
2
6.5
9
mV
mV
●
10
35
µV/°C
VOS TC
Input Offset Voltage Drift (Note 8)
IB
Input Bias Current
VCM = 1V
VCM = VS – 0.2V
●
●
200
3.4
1500
6.5
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = 1V
VCM = VS – 0.2V
●
●
150
150
2000
2200
nA
nA
IOS
Input Offset Current
VCM = 1V
VCM = VS – 0.2V
●
●
100
50
1600
1600
nA
nA
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 0.5V to 4.5V, RL = 1k to VS/2
VS = 5V, VO = 1.5V to 3.5V, RL = 100Ω to VS/2
VS = 3V, VO = 0.5V to 2.5V, RL=1k to VS/2
●
●
●
12
1.3
8
48
4.8
35
V/mV
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
●
●
69
60
95
90
dB
dB
CMRR Match (Channel-to-Channel) (Note 9) VS = 5V, VCM = 0V to 3V
VS = 3V, VCM = 0V to 1V
●
●
63
54
90
85
dB
dB
Input Common Mode Range
●
0
PSRR
Power Supply Rejection Ratio
VS = 2.5V to 10V, VCM = 0V
●
64
PSRR Match (Channel-to-Channel) (Note 9)
VS = 2.5V to 10V, VCM = 0V
●
58
Minimum Supply Voltage (Note 6)
VS
86
V
dB
86
dB
●
2.3
2.5
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 10mA
●
●
●
20
100
170
90
250
350
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 10mA
●
●
●
20
170
300
90
400
600
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
VS = 5V
VS = 3V
●
●
12
11
35
27
3.1
mA
mA
IS
Supply Current per Amplifier
GBW
Gain Bandwidth Product
VS = 5V, Frequency = 2MHz, RL = 1k to 2.5V
●
40
77
MHz
SR
Slew Rate
VS = 5V, AV = –1, RL = 1k to VS/2, VO = 0.5V to 4.5V
Measured at VO = 1.5V, 3.5V
●
30
70
V/µs
●
4.25
mA
180345f
5
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = ±5V, VCM = 0V, VOUT = 0V, unless otherwise noted
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage
VCM = –5V
VCM = –5V (DD Package)
VCM = –5V (SOT-23 Package)
VCM = 5V
∆VOS
Input Offset Shift
VCM = –5V to 3V
0.3
1
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = –5V
VCM = –5V (DD Package)
0.5
1
4
5.5
mV
mV
Input Bias Current
VCM = –4V
VCM = 5V
125
2.5
750
5.5
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = –4V
VCM = 5V
150
150
1250
1500
nA
nA
Input Offset Current
VCM = –4V
VCM = 5V
100
50
1000
1000
nA
nA
Input Noise Voltage
0.1Hz to 10Hz
en
Input Noise Voltage Density
f = 10kHz
21
nV/√Hz
in
Input Noise Current Density
f = 10kHz
2.5
pA/√Hz
CIN
Input Capacitance
f = 100kHz
2
pF
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –1.5V to 1.5V, RL = 100Ω
20
2
55
5
V/mV
V/mV
CMRR
Common Mode Rejection Ratio
VCM = –5V to 3V
78
96
dB
CMRR Match (Channel-to-Channel) (Note 9)
VCM = –5V to 3V
72
96
IB
IOS
MIN
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
MAX
UNITS
0.35
1.50
1.50
1.50
2.5
3.5
6
8
mV
mV
mV
mV
VS–␣ ␣
VS+
VS+
= 2.5V to 10V, VS–
= 2.5V to 10V, VS–
µVP-P
4
Input Common Mode Range
PSRR
TYP
= 0V, VOUT = VS
+/2
68
= 0V, VOUT = VS
+/2
62
dB
VS+
90
V
dB
90
dB
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 15mA
17
85
200
60
150
300
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 15mA
17
125
350
60
250
600
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
IS
Supply Current per Amplifier
3
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz, RL = 1k
83
MHz
SR
Slew Rate
AV = –1, RL = 1k, VO = ±4V
Measured at VO = ±2V
88
V/µs
FPBW
Full Power Bandwidth (Note 10)
VO = 8VP-P, AV = –1, RL = 1k
4
MHz
HD
Harmonic Distortion
AV = 1, RL = 1k, VO = 2VP-P, fC = 1MHz
–75
dBc
tS
Settling Time
0.01%, VSTEP = 5V, AV = 1, RL = 1k
500
ns
∆G
Differential Gain (NTSC)
AV = 2, RL = 150Ω
0.75
%
∆θ
Differential Phase (NTSC)
AV = 2, RL = 150Ω
0.8
Deg
25
50
2.5
mA
180345f
6
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the 0°C ≤ TA ≤ 70°C
temperature range. VS = ±5V, VCM = 0V, VOUT = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = –5V
VCM = –5V (DD Package)
VCM = –5V (SOT-23 Package)
VCM = 5V
●
●
●
●
MIN
0.5
1.5
1.5
1.4
3.5
5
7
8.5
mV
mV
mV
mV
∆VOS
Input Offset Shift
VCM = –5V to 3V
●
0.35
1.5
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = –5V
VCM = –5V (DD Package)
●
●
0.75
1.50
5.5
7.5
mV
mV
●
10
35
µV/°C
VOS TC
Input Offset Voltage Drift (Note 8)
IB
Input Bias Current
VCM = –4V
VCM = 4.8V
●
●
175
2.5
1000
6
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = –4V
VCM = 4.8V
●
●
175
175
1500
1800
nA
nA
IOS
Input Offset Current
VCM = –4V
VCM = 4.8V
●
●
100
50
1400
1400
nA
nA
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –1.5V to 1.5V, RL = 100Ω
●
●
15
1.5
47
4.5
V/mV
V/mV
Common Mode Rejection Ratio
VCM = –5V to 3V
●
74
95
dB
CMRR Match (Channel-to-Channel) (Note 9)
VCM = –5V to 3V
●
68
95
CMRR
●
VS+ = 2.5V to 10V, VS– = 0V, VOUT = VS+/2
VS+ = 2.5V to 10V, VS– = 0V, VOUT = VS+/2
●
65
87
dB
●
59
87
dB
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
dB
VS–
VS+
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 15mA
●
●
●
19
100
220
80
225
475
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 15mA
●
●
●
19
150
460
80
350
900
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
●
IS
Supply Current per Amplifier
●
2.8
20
46
mA
3.75
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz, RL = 1k
●
80
MHz
SR
Slew Rate
AV = –1, RL = 1k, VO = ±4V,
Measured at VO = ±2V
●
84
V/µs
180345f
7
LT1803/LT1804/LT1805
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the –40°C ≤ TA ≤ 85°C
temperature range. VS = ±5V, VCM = 0V, VOUT = 0V unless otherwise noted. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = –5V
VCM = –5V (DD Package)
VCM = –5V (SOT-23 Package)
VCM = 5V
●
●
●
●
MIN
1
2
2
2
4.0
6.5
8
9
mV
mV
mV
mV
∆VOS
Input Offset Shift
VCM = –5V to 3V
●
0.4
1.7
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 9)
VCM = –5V
VCM = –5V (DD Package)
●
●
1
2
6.5
9.0
mV
mV
●
10
35
µV/°C
VOS TC
Input Offset Voltage Drift (Note 8)
IB
Input Bias Current
VCM = –4V
VCM = 4.8V
●
●
250
2.5
1200
6.5
nA
µA
Input Bias Current Match
(Channel-to-Channel) (Note 9)
VCM = –4V
VCM = 4.8V
●
●
200
250
2000
2200
nA
nA
IOS
Input Offset Current
VCM = –4V
VCM = 4.8V
●
●
100
50
1600
1600
nA
nA
AVOL
Large-Signal Voltage Gain
VO = –4V to 4V, RL = 1k
VO = –1V to 1V, RL = 100Ω
●
●
12
1.4
45
5.3
V/mV
V/mV
Common Mode Rejection Ratio
VCM = –5V to 3V
●
73
95
dB
CMRR Match (Channel-to-Channel) (Note 9)
VCM = –5V to 3V
●
67
95
CMRR
●
VS+ = 2.5V to 10V, VS– = 0V, VOUT = VS+/2
VS+ = 2.5V to 10V, VS– = 0V, VOUT = VS+/2
●
64
86
dB
●
58
86
dB
Input Common Mode Range
PSRR
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 9)
dB
VS–
VS+
V
VOL
Output Voltage Swing Low (Note 7)
No Load
ISINK = 5mA
ISINK = 10mA
●
●
●
20
110
170
90
250
350
mV
mV
mV
VOH
Output Voltage Swing High (Note 7)
No Load
ISOURCE = 5mA
ISOURCE = 10mA
●
●
●
20
170
300
90
400
600
mV
mV
mV
ISC
Short-Circuit Current (Note 3)
●
IS
Supply Current per Amplifier
●
2.9
12.5
34
mA
4.25
mA
GBW
Gain Bandwidth Product
Frequency = 2MHz, RL = 1k
●
75
MHz
SR
Slew Rate
AV = –1, RL = 1k, VO = ±4V,
Measured at VO = ±2V
●
65
V/µs
Note 1: Absolute Maximium Ratings are those values beyond which the
life of the device may be impaired.
Note 2: The inputs are protected by back-to-back diodes and by ESD
diodes to supply rails. If the differential input voltage exceeds 1.4V, or if an
input is driven beyond the supply rails, the input current should be limited
to less than 10mA. This parameter is not tested; however it is guaranteed
by characterization.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The LT1803C/LT1803I, LT1804C/LT1804I and LT1805C/LT1805I
are guaranteed functional over the temperature range of –40°C and 85°C.
Note 5: The LT1803C/LT1804C/LT1805C are guaranteed to meet specified
performance from 0°C to 70°C. The LT1803C/LT1804C/LT1805C are
designed, characterized and expected to meet specified performance from
–40°C to 85°C but are not tested or QA sampled at these temperatures.
The LT1803I/LT1804I/LT1805I are guaranteed to meet specified performance from –40°C to 85°C.
Note 6: Minimum supply voltage is guaranteed by power supply rejection
ratio test.
Note 7: Output voltage swings are measured between the output and
power supply rails.
Note 8: This parameter is not 100% tested.
Note 9: Matching parameters are the difference between amplifiers A and
D and between B and C on the LT1805; between the two amplifiers on the
LT1804.
Note 10: Full power bandwidth is based on slew rate:
FPBW = SR/2πVP
180345f
8
LT1803/LT1804/LT1805
U W
TYPICAL PERFOR A CE CHARACTERISTICS
VOS Distribution, VCM = 0V
(SO-8, PNP Stage)
20
15
10
20
15
10
5
5
0
–1250
0
750
–250 0 250
–750
INPUT OFFSET VOLTAGE (µV)
1250
4
–2
0
2
–4
INPUT OFFSET VOLTAGE (mV)
–6
25
20
15
10
0
–5 – 4
6
5.0
VS = 5V, 0V
VCM = 5V
2000
PER AMPLIFIER
VS = 5V, 0V
TYPICAL PART
1500
SUPPLY CURRENT (mA)
4.0
10
5
5
Offset Voltage vs Input Common
Mode Voltage
4.5
20
4
180345 G03
Supply Current vs Supply Voltage
15
1 2 3
–3 –2 –1 0
INPUT OFFSET VOLTAGE (mV)
180345 G02
VOS Distribution, VCM = 5V
(SOT-23, NPN Stage)
PERCENT OF UNITS (%)
30
5
180345 G01
25
VS = 5V, 0V
VCM = 0V
35
PERCENT OF UNITS (%)
25
25
40
VS = 5V, 0V
VCM = 5V
3.5
OFFSET VOLTAGE (µV)
PERCENT OF UNITS (%)
30
30
VS = 5V, 0V
VCM = 0V
PERCENT OF UNITS (%)
35
VOS Distribution, VCM = 0V
(SOT-23, PNP Stage)
VOS Distribution, VCM = 5V
(SO-8, NPN Stage)
TA = 125°C
3.0
TA = 25°C
2.5
TA = –55°C
2.0
1.5
1.0
1000
TA = 125°C
500
TA = 25°C
0
TA = –55°C
–500
0.5
–6
–2
0
2
4
–4
INPUT OFFSET VOLTAGE (mV)
0
6
0
1
2
3 4 5 6 7 8 9 10 11 12
TOTAL SUPPLY VOLTAGE (V)
180345 G04
3
INPUT BIAS CURRENT (µA)
INPUT BIAS CURRENT (µA)
2.5
TA = 125°C
0
TA = 25°C
–1
2.0
–1
0
3
2
1
4
5
COMMON MODE VOLTAGE (V)
6
180345 G07
NPN ACTIVE
VS = 5V, 0V
VCM = 5V
1.0
0.5
–0.5
–2
10
1.5
0
5
Output Saturation Voltage vs
Load Current (Output Low)
3.0
VS = 5V, 0V
TA = –55°C
1
2
3
4
INPUT COMMON MODE VOLTAGE (V)
180345 G06
Input Bias Current vs
Temperature
2
0
180345 G05
Input Bias Current vs Common
Mode Voltage
1
–1000
OUTPUT SATURATION VOLTAGE (V)
0
PNP ACTIVE
VS = 5V, 0V
VCM = 1V
–1.0
–50 –35 –20 –5 10 25 40 55
TEMPERATURE (°C)
70
85
180345 G08
VS = 5V, 0V
1
TA = 125°C
0.1
0.01
TA = 25°C
TA = –55°C
0.001
0.01
1
10
0.1
LOAD CURRENT (mA)
100
180345 G09
180345f
9
LT1803/LT1804/LT1805
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Saturation Voltage vs
Load Current (Output High)
6
1
TA = 125°C
TA = 25°C
0.1
TA = –55°C
0.01
0.001
0.01
4
TA = 125°C
2
TA = 25°C
0
TA = –55°C
–2
–4
–6
100
0.1
1
10
LOAD CURRENT (mA)
0
0
SOURCING
RL = 1k
0
–0.5
–1.0
–40
8
1.0
RL = 100Ω
0.5
RL = 1k
0
–0.5
–1.0
–4
–8
1
3
2
OUTPUT VOLTAGE (V)
4
TA = 125°C
2
0
TA = –55°C
TA = 25°C
–4
20
0
40
–20
OUTPUT CURRENT (mA)
60
80
180345 G16
160
VS = ±5V
10
VS = 5V
5
VS = 3V
0
–5
–10
–15
25
10
15
20
5
TIME AFTER POWER-UP (SECONDS)
30
180345 G17
VS = 5V, 0V
140
120
100
80
PNP ACTIVE
VCM = 2.5V
60
40
20
0
5
Input Noise Voltage
vs Frequency
INPUT NOISE VOLTAGE (nV/√Hz)
CHANGE IN OFFSET VOLTAGE (µV)
6
4
180345 G15
15
VS = ±5V
–6
–60 –40
5
Warm-Up Drift vs Time
(LT1804S8)
Offset Voltage Change
vs Output Current
–2
4
180345 G14
180345 G13
8
–10
–5 –4 –3 –2 –1 0 1 2 3
OUTPUT VOLTAGE (V)
–2.5
0
RL = 1k
–2
–6
3.0
RL = 100Ω
0
–2.0
2.5
5.0
VS = ±5V
RL TO GND
2
–2.0
1.5
2.0
1.0
OUTPUT VOLTAGE (V)
4.5
4.0
2.0
2.5 3.0 3.5
POWER SUPPLY VOLTAGE (±V)
4
–1.5
0.5
TA = 25°C
6
–1.5
0
TA = –55°C
TA = 125°C
–20
Open-Loop Gain
INPUT VOLTAGE (mV)
INPUT VOLTAGE (mV)
INPUT VOLTAGE (mV)
RL = 100Ω
TA = 125°C
20
10
1.5
–2.5
CHANGE IN OFFSET VOLTAGE (mV)
TA = –55°C
180345 G12
VS = 5V, 0V
RL TO GND
2.0
1.5
0.5
TA = 25°C
40
Open-Loop Gain
2.5
VS = 3V, 0V
RL TO GND
1.0
SINKING
180345 G11
Open-Loop Gain
2.0
60
–60
1.5
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
TOTAL SUPPLY VOLTAGE (V)
180345 G10
2.5
80
VCM = 0V
OUTPUT SHORT-CIRCUIT CURRENT (mA)
VS = 5V, 0V
CHANGE IN OFFSET VOLTAGE (mV)
OUTPUT SATURATION VOLTAGE (V)
10
Output Short-Circuit Current vs
Power Supply Voltage
Minimum Supply Voltage
NPN ACTIVE
VCM = 4.25V
0
0.01
0.1
10
1
FREQUENCY (kHz)
100
180345 G18
180345f
10
LT1803/LT1804/LT1805
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Input Current Noise
vs Frequency
6
5
PNP ACTIVE
VCM = 2.5V
3
NPN ACTIVE
VCM = 4.25V
2
VS = 5V, 0V
4
2
0
0.01
0.1
–6
100
10
1
FREQUENCY (kHz)
1
3
2
4 5 6 7
TIME (SECONDS)
VS = ±5V
90
40
PHASE MARGIN
VS = ±5V
PHASE
MARGIN (DEG)
VS = ±2.5V
–25
0
25
50
75
TEMPERATURE (°C)
VS = ±2.5V
70
24
18
12
12
6
6
–6
–12
VS = ±2.5V
VS = ±5V
100
125
120
40
140
GAIN
20
160
TA = 25°C
CL = 5pF
RL = 1k
VS = ±5V
VS = ±2.5V
–40
0.01
0.1
–12
–18
–24
100
300
180345 G25
180
200
1
10
FREQUENCY (MHz)
–30
0.1
220
100 300
180345 G24
Output Impedance vs Frequency
1000
CL = 10pF
RL = 100Ω
AV = 2
–6
–18
1
10
FREQUENCY (MHz)
60
–20
VS = ±2.5V
100
VS = ±2.5V
0
–24
–30
0.1
100
Gain vs Frequency (AV = 2)
30
CL = 10pF
RL = 100Ω
AV = 1
0
80
180345 G23
GAIN (dB)
GAIN (dB)
18
80
PHASE
0
0
25
50
75
TEMPERATURE (°C)
10
60
100
60
–25
9
Gain and Phase vs Frequency
80
Gain vs Frequency (AV = 1)
24
2 3 4 5 6 7 8
TOTAL SUPPLY VOLTAGE (V)
120
AV = –1
RF = RG = 1k
RL = 1k
180345 G22
30
1
180345 G21
VS = ±5V
40
–50
125
100
40
0
50
30
20
–50
PHASE MARGIN
50
10
GAIN (dB)
100
SLEW RATE (V/µs)
VS = ±2.5V
60
40
60
PHASE SHIFT (DEG)
GAIN
BANDWIDTH (MHz)
110
GAIN BANDWIDTH
50
9
8
Slew Rate vs Temperature
120
60
80
180345 G20
Gain Bandwidth and Phase
Margin vs Temperature
80
GAIN BANDWIDTH
PRODUCT
100
30
0
180345 G19
100
TA = 25°C
60
–2
–4
1
120
0
PHASE
MARGIN (DEG)
INPUT NOISE VOLTAGE (µV)
INPUT NOISE CURRENT (pA/√Hz)
7
GAIN
BANDWIDTH (MHz)
6
VS = 5V, 0V
VS = ±5V
OUTPUT IMPEDANCE (Ω)
8
4
Gain Bandwidth and Phase
Margin vs Supply Voltage
0.1Hz to 10Hz Voltage Noise
AV = 10
10
AV = 1
1
AV = 2
0.1
0.01
1
10
FREQUENCY (MHz)
100 300
180345 G26
0.001
0.1
1
10
100
FREQUENCY (kHz)
1000
180345 G27
180345f
11
LT1803/LT1804/LT1805
U W
TYPICAL PERFOR A CE CHARACTERISTICS
80
60
40
20
0
0.01
0.1
1
10
FREQUENCY (MHz)
100
80
60
40
NEGATIVE
SUPPLY
50
40
30
100
0
5
0
0.1
1
FREQUENCY (MHz)
10
100
15
100
1000
CAPACITIVE LOAD (pF)
10000
VS = 5V, 0V
AV = 2
– 40 V
OUT = 2VP-P
– 60
RL = 150Ω, 2ND
– 70
– 80
RL = 150Ω, 3RD
RL = 1kΩ, 2ND
–110
0.01
RL = 1kΩ, 3RD
0.1
1
FREQUENCY (MHz)
180345 G31
10
– 50
RL = 150Ω, 3RD
– 60
– 70
RL = 150Ω, 2ND
– 80
RL = 1kΩ, 3RD
RL = 1kΩ, 2ND
– 90
–100
0.01
0.1
1
FREQUENCY (MHz)
10
180345 G33
180345 G32
Maximum Undistorted Output
Signal vs Frequency
10000
–30
–100
5
100
1000
CAPACITIVE LOAD (pF)
Distortion vs Frequency (AV = 2)
Distortion vs Frequency (AV = 1)
–30
– 90
RS = 20Ω
10
180345 G30
DISTORTION (dBc)
RS = 50Ω,
RL = 50Ω
RS = 50Ω,
RL = 50Ω
15
180345 G29
DISTORTION (dBc)
OVERSHOOT (%)
30
10
20
VS = 5V, 0V
– 40 AV = 1
VOUT = 2VP-P
– 50 VCM = 2V
VS = 5V, 0V
45 AV = 2
CF = 5pF
40 R = 1k
G
35 RF = 1k
0
25
10
0.01
RS = 20Ω
30
10
–10
0.001
50
10
35
20
Overshoot and Series Output
Resistor vs Capacitive Load (AV = 2)
20
VS = 5V, 0V
45 AV = 1
POSITIVE
SUPPLY
70
180345 G28
25
50
VS = 5V, 0V
TA = 25°C
90
OVERSHOOT (%)
VS = 5V, 0V
RL = 1kΩ
TA = 25°C
POWER SUPPLY REJECTION RATIO (dB)
COMMON MODE REJECTION RATIO (dB)
100
Overshoot and Series Output
Resistor vs Capacitive Load (AV = 1)
Power Supply Rejection Ratio
vs Frequency
Common Mode Rejection Ratio
vs Frequency
5V Small-Signal Response
5V Large-Signal Response
OUTPUT VOLTAGE SWING (VP-P)
5.2
5.0
AV = –1
50mV/DIV
4.8
2.5V
1V/DIV
4.6
AV = 2
0V
4.4
4.2 VS = 5V, 0V
TA = 25°C
HD2, HD3 < –40dBc
4.0
0.01
0.1
1
FREQUENCY (MHz)
VS = 5V, 0V
AV = 1
RL = 1k
100ns/DIV
180345 G35
VS = 5V, 0V
AV = 1
RL = 1k
50ns/DIV
180345 G36
10
180345 G34
180345f
12
LT1803/LT1804/LT1805
U W
TYPICAL PERFOR A CE CHARACTERISTICS
±5V Large-Signal Response
±5V Small-Signal Response
0V
Output Overdrive Recovery
50mV/DIV
VIN
1V/DIV
0V
0V
2V/DIV
VOUT
2V/DIV
180345 G37
W
200ns/DIV
VS = ±5V
AV = 1
RL = 1k
50ns/DIV
180345 G38
VS = 5V, 0V
AV = 2
RL = 1k
100ns/DIV
180345 G39
U
VS = ±5V
AV = 1
RL = 1k
U U
APPLICATIO S I FOR ATIO
Circuit Description
Power Dissipation
The LT1803/LT1804/LT1805 have input and output signal
ranges from the negative power supply to the positive
power supply. Figure 1 depicts a simplified schematic of
one amplifier. The input stage is comprised of two differential amplifiers, a PNP stage Q1/Q2 and an NPN stage Q3/
Q4 that are active over the different ranges of the common
mode input voltage. The PNP differential pair is active
between the negative supply and approximately 1.3V
below the positive supply. As the input voltage moves
toward the positive supply, the transistor Q5 will steer the
tail current I1 to the current mirror Q6/Q7 activating the
NPN differential pair. The PNP pair becomes inactive for
the rest of the input common mode range up to the positive
supply. Also at the input stage, devices Q18 and Q19 act
to cancel the bias current of the PNP input pair. When Q1
and Q2 are active, the current in Q16 is controlled to be the
same as the current in Q1 and Q2; therefore, the base
current of Q16 is nominally equal to the base current of the
input devices. The base current of Q16 is then mirrored by
devices Q17 through Q19 to cancel the base current of the
input devices Q1 and Q2.
There is a need to ensure that the die’s junction temperature does not exceed 150°C. Junction temperature TJ is
calculated from the ambient temperature TA, power dissipation PD and thermal resistance θJA:
A pair of complementary common emitter stages Q14/
Q15 that enable the output to swing from rail-to-rail
constructs the output stage. The capacitors C1 and C2
form the local feedback loops that lower the output
impedance at high frequency. The LT1803/LT1804/LT1805
are fabricated on Linear Technology’s proprietary high
speed complementary bipolar process.
TJ = TA + (PD • θJA)
The power dissipated in the IC is a function of the supply
voltage, amplifier current, output voltage and output current. For a given supply voltage, the worst-case power
dissipation, PDMAX, occurs when the output current and
voltage drop in the amplifier product is maximized. For
example, if the amplifier is sourcing a constant current
then the PDMAX occurs when the output voltage is at about
VS–. On the other hand, for a given load resistance to
ground, the PDMAX will occur when the output voltage is at
half of either supply voltage. PDMAX for a given resistance
to ground is given by:
PDMAX = (VS+ – VS–) ISMAX + (VS/2)2/RL
Example: An LT1804 in an SO-8 package operating on ±5V
supplies and driving a 100Ω load to ground, the PDMAX per
amplifier is given by:
PDMAX = (10 • 3.25mA) + (2.5)2/100 = 0.0425 + 0.0625
= 0.095W
ISMAX is approximated for a typical part from the Supply
Currrent vs Supply Voltage graph.
180345f
13
LT1803/LT1804/LT1805
U
W
U U
APPLICATIO S I FOR ATIO
V+
R3
V+
+
R5
V–
ESDD1
I2
R4
+
D1
ESDD2
Q12
Q11
I1
Q13
+IN
D6
D5
D8
D2
Q5
OUT
D3
BUFFER
AND
OUTPUT BIAS
Q10
V+
D4
Q9
Q16
Q17
V–
Q1 Q2
ESDD3
V–
I3
CC
Q4 Q3
ESDD4
+
VBIAS
D7
–IN
Q15
C2
Q8
C1
Q18
Q19
Q7
Q14
Q6
R1
V–
R2
180345 F01
Figure 1. LT1803/LT1804/LT1805 Simplified Schematic Diagram
If both amplifiers are loaded simultaneously, then the total
power dissipation is 0.19W.
voltage is typically less than 1000µV in the range the PNP
input stage is active.
The maximum ambient temperature that the part is allowed to operate is:
Input Bias Current
TA = TJ – (PDMAX • 190°C/W)
= 150°C – (0.190W • 190°C/W) = 113.9°C
Similar calculations can be carried out for specific packages and conditions.
Also worth noting, the DD package includes a low θJA
underside metal which is internally connected to VS–. If the
underside metal is properly soldered to a PCB, the θJA of
the part will be close to 50°C/W. This θJA is significantly
less than leaving the underside metal unattached and can
be useful for certain applications.
Input Offset Voltage
The input offset voltage will change greatly based upon
which input stage is active. The PNP input stage is active
from the negative supply voltage to about 1.3V below the
positive supply rail, then the NPN input stage is activated
for the remaining input range up to the positive supply rail
during which the PNP stage remains inactive. The offset
The LT1803/LT1804/LT1805 employ a patent-pending
technique to reduce the input bias current to less than 1µA
for the input common mode voltage range of 0.2V above
the negative supply rail to 1.75V below the positive rail.
The low input offset voltage and low input bias current
provide precision performance in high source impedance
applications.
Output
The LT1803/LT1804/LT1805 can deliver a large output
current, so the short-circuit current limit is set around
50mA to prevent damage to the device. Attention must be
paid to keep the junction temperature of the IC below the
absolute maximum rating of 150°C (refer to the Power
Dissipation section) when the output is continuously short
circuited. The output of the amplifier has reverse-biased
diodes connected to each supply. If the output is forced
beyond either supply, unlimited current will flow through
these diodes. If the current is transient and limited to less
than 100mA and the total supply voltage is less than
180345f
14
LT1803/LT1804/LT1805
U
W
U U
APPLICATIO S I FOR ATIO
12.6V, the absolute maximum rating, no damage will
occur to the device.
Overdrive Protection
When the input voltage exceeds the power supplies, two
pairs of crossing diodes D1 through D4 will prevent the
output from reversing polarity. If the input voltage exceeds
either power supply by 700mV, diode D1/D2 or D3/D4 will
turn on to keep the output at the proper polarity. For the
phase reversal protection to perform properly, the input
current must be limited to less than 10mA. If the amplifier
is severely overdriven, an external resistor should be used
to limit the overdrive current.
The LT1803/LT1804/LT1805’s input stages are also protected against a large differential input voltage of 1.4V or
higher by a pair of back-to-back diodes D5 through D8 to
prevent the emitter-base breakdown of the input transistors. The current in these diodes should be limited to less
than 10mA when they are active. The worst-case differential input voltage usually occurs when the input is driven
while the output is shorted to ground in a unity gain
configuration. In addition, the amplifier is protected against
ESD strikes up to 3kV on all pins by a pair of protection
diodes on each pin that is connected to the power supplies
as shown in Figure 1.
Capacitive Load
The LT1803/LT1804/LT1805 are optimized for wide bandwidth, low power and precision applications. They can
drive a capacitive load of about 20pF in a unity-gain
configuration, and more for higher gain. When driving a
larger capacitive load, a resistor of 10Ω to 50Ω should be
connected between the output and the capacitive load to
avoid ringing or oscillation. The feedback should still be
taken from the output so that the resistor will isolate the
capacitive load to ensure stability. Graphs on capacitive
load indicate the transient response of the amplifier when
driving a capacitive load with a specified resistor.
Feedback Components
When feedback resistors are used to set up gain, care must
be taken to ensure that the pole formed by the feedback
resistors and the total capacitance at the inverting input
does not degrade stability. For instance, the LT1803/
LT1804/LT1805 in a noninverting gain of 2 setup with two
5k resistors and a capacitance of 5pF (part plus PC board)
will probably oscillate. The pole formed at 12.7MHz,
reduces phase margin by about 58 degrees when the
crossover frequency of the amplifier is around 20MHz. A
capacitor of 5pF or higher connected across the feedback
resistor will eliminate any ringing or oscillation.
180345f
15
LT1803/LT1804/LT1805
U
PACKAGE DESCRIPTIO
S5 Package
5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
0.62
MAX
0.95
REF
2.90 BSC
(NOTE 4)
1.22 REF
1.4 MIN
3.85 MAX 2.62 REF
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45 TYP
5 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
1.90 BSC
S5 TSOT-23 0302
180345f
16
LT1803/LT1804/LT1805
U
PACKAGE DESCRIPTIO
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
0.675 ±0.05
3.5 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.28 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
5
3.00 ±0.10
(4 SIDES)
0.38 ± 0.10
8
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(DD8) DFN 0203
0.200 REF
0.75 ±0.05
0.00 – 0.05
4
0.28 ± 0.05
1
0.50 BSC
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. ALL DIMENSIONS ARE IN MILLIMETERS
3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
4. EXPOSED PAD SHALL BE SOLDER PLATED
180345f
17
LT1803/LT1804/LT1805
U
PACKAGE DESCRIPTIO
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
7
6
5
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.053 – .069
(1.346 – 1.752)
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 0303
180345f
18
LT1803/LT1804/LT1805
U
PACKAGE DESCRIPTIO
S Package
14-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.337 – .344
(8.560 – 8.738)
NOTE 3
.045 ±.005
.050 BSC
14
N
12
11
10
9
8
N
.245
MIN
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
1
.030 ±.005
TYP
13
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
1
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
2
3
4
5
6
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.014 – .019
(0.355 – 0.483)
TYP
7
.050
(1.270)
BSC
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
S14 0502
180345f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1803/LT1804/LT1805
U
TYPICAL APPLICATIO
500mA Pulse Response of LED Array Driver
LED Array Driver
10V
3.01k
3
VIN
+
5V
7
6
332Ω
10Ω
LT1803
2
–
4
INTERNATIONAL
RECTIFIER
IRLL3303
IOUT
PIN 3
0V
27pF
VSENSE
•••
332Ω
0V
2 FOOT WIRE
VSENSE
IOUT = VIN • 1A
RSENSE
0.1Ω
(NOT CURRENT LIMITED UNDER
SHORT-CIRCUIT CONDITIONS)
SCANNER LED ARRAY
RATED 600mA AT 5V
PIN 6
FET
SOURCE
0V
1803 TAO3a
1803 TA03b
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1399
Triple 300MHz Current Feedback Amplifier
0.1dB Gain Flatness to 150MHz, Shutdown
LT1498/LT1499
Dual/Quad 10MHz, 6Vµs Rail-to-Rail Input and Output
C-LoadTM Op Amps
High DC Accuracy, 475µV VOS(MAX), 4µV/°C Max Drift,
Max Supply Current 2.2mA per Amp
LT1630/LT1631
Dual/Quad 30MHz, 10V/µs Rail-to-Rail Input and Output Op Amps
High DC Accuracy, 525µV VOS(MAX), 70mA Output Current,
Max Supply Current 4.4mA per Amplifier
LT1800/LT1801
LT1802
Single/Dual/Quad 80MHz, 25V/µs Low Power Rail-to-Rail
Input/Output Precision Op Amps
High DC Accuracy, 350µV VOS(MAX), Max Supply Currrent
2mA per Amplifier
LT1806/LT1807
Single/Dual 325MHz, 140V/µs Rail-to-Rail Input/Output Amps
High DC Accuracy, 550µV VOS(MAX), Low Noise 3.5nV/√Hz,
Low Distortion – 80dB at 5MHz, Power-Down (LT1806)
LT1809/LT1810
Single/Dual 180MHz Rail-to-Rail Input/Output Op Amps
350V/µs Slew Rate, Low Distortion – 90dB at 5MHz,
Power-Down (LT1809)
LT6200/LT6201
Single/Dual Ultralow Noise Rail-to-Rail Amplifier
0.95nV/Hz, 165MHz Gain Bandwidth, 44V/µs
LT6200-5
Single Ultralow Noise Rail-to-Rail Amplifier
0.95nV/Hz, 800MHz Gain Bandwidth, 210V/µs, AV ≥5
LT6200-10
Single Ultralow Noise Rail-to-Rail Amplifier
0.95nV/Hz, 1.6GHz Gain Bandwidth, 340V/µs, AV ≥10
LT6202/LT6203
LT6204
Single/Dual/Quad 90MHz, 24V/µs Rail-to-Rail Input/Output,
Ultralow 1.9nV/√Hz Noise, Low Power Op Amps
High DC Accuracy, 500µV VOS(MAX), Max Supply Currrent
3mA per Amplifier
C-Load is a trademark of Linear Technology Corporation.
180345f
20
Linear Technology Corporation
LT/TP 0803 1K • PRINTED IN THE USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2003