LPC-60 60W Single Output Switching Power Supply series Features : Constant current design Universal AC input / Full range Epoxy encapsulated with IP67 level Withstand 300VAC surge input for 5 seconds Protections: Short circuit / Over current / Over voltage Fully isolated plastic case Cooling by free air convection UL1310 Class 2 power unit, pass LPS 100% full load burn-in test Low cost, high reliability Suitable for LED lighting and moving sign applications 2 years warranty LPS IP67 SPECIFICATION MODEL OUTPUT ( for 34V only) LPC-60-1050 LPC-60-1400 LPC-60-1750 DC VOLTAGE 48V 42V 34V DC VOLTAGE RANGE 9 ~ 48V 9 ~ 42V 9 ~ 34V CURRENT RANGE 1050mA 1400mA 1750mA RATED POWER 50.4W 58.8W 59.5W 200mVp-p 200mVp-p RIPPLE & NOISE (max.) Note.2 200mVp-p VOLTAGE TOLERANCE Note.3 5.0% LINE REGULATION 1.0% 2.0% LOAD REGULATION SETUP, RISE TIME INPUT ( except for 34V ) Note.6 500ms, 120ms / 230VAC 500ms, 120ms / 115VAC at full load HOLD UP TIME (Typ.) 50ms/230VAC VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 87% AC CURRENT INRUSH CURRENT(max.) 1.2A/115VAC 0.7A/230VAC COLD STAR 30A/115VAC 60A/230VAC LEAKAGE CURRENT 0.25mA / 240VAC CURRENT LIMIT Note.4 PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 16ms/115VAC at full load 85% 5% rated output current Protection type : Constant current limiting type 50.4 ~ 60V 44.1 ~ 56.7V 87% 39.1 ~ 45.9V Protection type : Shut off o/p voltage, clamping by TVS diode -30 ~ +70 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +80 , 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL1310 Class 2, CAN/CSA C22.2 No. 223-M91(for 34V only), IP67 approved, design refer to TUV EN60950-1, EN61347-2-13 WITHSTAND VOLTAGE I/P-O/P:3KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B OTHERS HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A 732Khrs min. MIL-HDBK-217F (25 ) DIMENSION 162.5*42.5*32mm (L*W*H) 0.4Kg; 32pcs/13.8Kg/0.56CUFT PACKING NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the derating curve for more details. 5. The power supply is considered a component which will be installed a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:LPC-60-SPEC 2008-12-11 LPC-60 60W Single Output Switching Power Supply Mechanical Specification Case No. 976A 600 162.5 series Unit:mm 600 18AWG 3.6 16AWG 42.5 3.6 3.5 AC/L(Brown) AC/N(Blue) 3.5 3.5 +V(Red) -V(Black) 32 3.5 Block Diagram fosc : 60KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING +V -V O.C.P. O.L.P. PWM CONTROL Derating Curve DETECTION CIRCUIT Static Characteristics Ta=25 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -30 -15 0 15 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 264 INPUT VOLTAGE (V) 60Hz File Name:LPC-60-SPEC 2008-12-11