QP-375 375W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC fan CH3,4 are isolated from other outputs and the polarity can be reversed No minimum load requirement for CH2,3,4 All output can be adjustable from -5~+10% With power good and fail signal output Built-in remote ON-OFF control Fixed switching frequency at 100KHz 3 years warranty .. SPECIFICATION QP-375-5A MODEL OUTPUT QP-375-5C CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V +12V 12V 12V +5V +12V 12V 5V 5V +12V 15V 15V RATED CURRENT 30A 10A 6A 3A 30A 10A 6A 3A 30A 9A CURRENT RANGE 3.5 ~ 40A 0 ~ 16A 0 ~ 6A 0 ~ 3A 3.5 ~ 40A 0 ~ 16A 0 ~ 6A 0 ~ 3A 3.5 ~ 40A 0 ~ 16A RATED POWER(max.) 378W 357W 4A 4A 0 ~ 4A 0 ~ 4A 378W RIPPLE & NOISE (max.) Note.2 100mVp-p 150mVp-p 150mVp-p 50mVp-p 100mVp-p 120mVp-p 120mVp-p 50mVp-p 100mVp-p 150mVp-p 150mVp-p 240mVp-p 4.75 ~ 5.5V 11.4 ~ 13.2V 11.4 ~ 13.2V 11.4 ~ 13.2V 4.75 ~ 5.5V 11.4 ~ 13.2V 11.4 ~ 13.2V ------ VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 11.4 ~ 13.2V 14.3 ~ 16.5V 14.3 ~ 16.5V VOLTAGE TOLERANCE Note.3 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 36ms at full load HOLD UP TIME (Typ.) VOLTAGE RANGE 1.0% 800ms, 50ms at full load SETUP, RISE TIME INPUT QP-375-5B OUTPUT NUMBER Note.7 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 77% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 6A/115VAC 3A/230VAC COLD START 45A PF>0.98/115VAC at full load 77% LEAKAGE CURRENT <2mA / 240VAC OVERLOAD 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 77% CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover 80 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms FUNCTION RC+/RC-:0 ~ 0.8V POWER ON; 4V ~ 10V POWER OFF REMOTE CONTROL OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT EMS IMMUNITY OTHERS (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A MTBF 75.9K hrs min. DIMENSION 280*127*63.5mm (L*W*H) 2.4Kg; 6pcs/14.8Kg/1.45CUFT PACKING NOTE -10 ~ +60 MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Peak current can not exceed 60 sec. 6. Isolated CH3 & CH4 maybe series connected or can be used as positive or negative outputs. 7. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-375-SPEC 2007-04-11 QP-375 375W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC fan CH3,4 are isolated from other outputs and the polarity can be reversed No minimum load requirement for CH2,3,4 All output can be adjustable from -5~+10% With power good and fail signal output Built-in remote ON-OFF control Fixed switching frequency at 100KHz 3 years warranty .. SPECIFICATION QP-375-5D MODEL OUTPUT CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE +5V +12V 12V 24V +5V +12V 24V 24V RATED CURRENT 30A 9A 4A 3A 30A 9A 3A 2A CURRENT RANGE 3.5 ~ 40A 0 ~ 16A 0 ~ 6A 0 ~ 3A 3.5 ~ 40A 0 ~ 16A 0 ~ 4A 0 ~ 3A RATED POWER(max.) 378W 120mVp-p 120mVp-p 240mVp-p 100mVp-p 120mVp-p 120mVp-p 240mVp-p 11.4 ~ 13.2V 11.4 ~ 13.2V 22.8 ~ 26.4V 4.75 ~ 5.5V 11.4 ~ 13.2V 22.8 ~ 26.4V 22.8 ~ 26.4V 378W RIPPLE & NOISE (max.) Note.2 100mVp-p 4.75 ~ 5.5V VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 800ms, 50ms at full load SETUP, RISE TIME 36ms at full load HOLD UP TIME (Typ.) VOLTAGE RANGE INPUT QP-375-5E OUTPUT NUMBER Note.7 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 78% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 6A/115VAC 3A/230VAC COLD START 45A PF>0.98/115VAC at full load 78% LEAKAGE CURRENT <2mA / 240VAC OVERLOAD 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover 80 5 (TSW1): Detect on heatsink of Q1,Q2 power transistor) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms FUNCTION RC+/RC-:0 ~ 0.8V POWER ON; 4V ~ 10V POWER OFF REMOTE CONTROL OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & EMC (Note 5) -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A MTBF 75.9K hrs min. DIMENSION 280*127*63.5mm (L*W*H) 2.4Kg; 6pcs/14.8Kg/1.45CUFT PACKING NOTE (Refer to output load derating curve) 20 ~ 90% RH non-condensing ISOLATION RESISTANCE HARMONIC CURRENT EMS IMMUNITY OTHERS -10 ~ +60 MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Peak current can not exceed 60 sec. 6. Isolated CH3 & CH4 maybe series connected or can be used as positive or negative outputs. 7. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-375-SPEC 2007-04-11 QP-375 375W Quad Output with PFC Function Mechanical Specification Case No. 927A series Unit:mm 92 63.5 250 +V2 ADJ. 9.5 8.2 I/P 1 2 3 +V3 ADJ. +V4 ADJ. 37 1 6 99.1 99.1 113 6-M3 L=6 127 8.2 8-M4 L=6 CN62 42.5 30.4 165.1 +V1 ADJ. TB1 1 2 3 4 5 6 7 8 9 10 9.5 O/P TB2 5 7 LED Air flow direction 165.1 165.1 240 42.4 31.7 13.9 10.1 280 2-M4 L=6 CN62 Pin No. Assignment : JST S6B-XH or equivalent AC Input Terminal Pin No. Assignment Assignment AC/L AC/N FG Pin No. 1 2 3 Pin No. Assignment Mating Housing Terminal 1 PF(Power good / Fail signal) GND 2 RS3 JST XHP JST SXH-001T-P0.6 RS+ or equivalent or equivalent 4 RC5 RC+ 6 DC Output Terminal Pin No. Assignment Pin No. 1,2 3,4,5 6 7 Assignment +V1 COM(V1 and V2) +V2 +V3 Pin No. 8 9 10 Assignment -V3 +V4 -V4 Block Diagram fosc : 100KHz POWER SWITCHING PWM CONTROL ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & P.F.C. FAN POWER SWITCHING RECTIFIERS & FILTER REGULATOR MA & CONTROL RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER +V4 -V4 +V3 -V3 +S +V1 COM -S +V2 PF FG O.L.P. O.T.P. PF PWM CONTROL Derating Curve O.V.P. DETECTION CIRCUIT +RC -RC Output Derating VS Input Voltage 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 85 95 105 115 125 135 180 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-375-SPEC 2007-04-11 QP-375-24 375W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC fan CH3,4 are isolated from other outputs and the polarity can be reversed No minimum load requirement for CH2,3,4 All output can be adjustable from -5~+10% With power good and fail signal output Built-in remote ON-OFF control Fixed switching frequency at 100KHz 3 years warranty .. SPECIFICATION QP-375-24B MODEL OUTPUT CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE +24V +5V 12V 12V +24V +5V 15V 15V RATED CURRENT 10A 10A 4A 4A 10A 10A 4A 4A CURRENT RANGE 1 ~ 10A 0 ~ 16A 0 ~ 4A 0 ~ 4A 1 ~ 10A 0 ~ 10A 0 ~ 4A 0 ~ 4A RATED POWER(max.) 386W 50mVp-p 120mVp-p 120mVp-p 240mVp-p 50mVp-p 150mVp-p 150mVp-p 4.5 ~ 5.5V 10.8 ~ 13.2V 10.8 ~ 13.2V 21.6 ~ 26.4V 4.5 ~ 5.5V 13.5 ~ 16.5V 13.5 ~ 16.5V 410W RIPPLE & NOISE (max.) Note.2 240mVp-p 21.6 ~ 26.4V VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8% 800ms, 50ms at full load SETUP, RISE TIME 36ms at full load HOLD UP TIME (Typ.) VOLTAGE RANGE INPUT QP-375-24C OUTPUT NUMBER Note.7 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 78% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 6A/115VAC 3A/230VAC COLD START 45A PF>0.98/115VAC at full load 80% LEAKAGE CURRENT <2mA / 240VAC OVERLOAD 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after condition is removed PROTECTION OVER VOLTAGE CH1:27.6 ~ 32.4V Protection type : Shut down o/p voltage, re-power on to recover 80 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms FUNCTION RC+/RC-:0 ~ 0.8V POWER ON; 4V ~ 10V POWER OFF REMOTE CONTROL OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT EMS IMMUNITY OTHERS (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A MTBF 75.9K hrs min. DIMENSION 280*127*63.5mm (L*W*H) 2.4Kg; 6pcs/14.8Kg/1.45CUFT PACKING NOTE -10 ~ +60 MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Peak current can not exceed 60 sec. 6. Isolated CH3 & CH4 maybe series connected or can be used as positive or negative outputs. 7. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-375-24-SPEC 2007-04-11 QP-375-24 375W Quad Output with PFC Function Mechanical Specification Case No. 927A 92 63.5 250 +V2 ADJ. 9.5 8.2 I/P 1 2 3 +V3 ADJ. +V4 ADJ. 37 1 6 99.1 99.1 113 6-M3 L=6 127 8.2 8-M4 L=6 CN62 42.5 30.4 165.1 +V1 ADJ. TB1 1 2 3 4 5 6 7 8 9 10 9.5 O/P TB2 5 7 LED Air flow direction Unit:mm 165.1 165.1 240 42.4 31.7 13.9 10.1 280 series 2-M4 L=6 CN62 Pin No. Assignment : JST S6B-XH or equivalent AC Input Terminal Pin No. Assignment Assignment AC/L AC/N FG Pin No. 1 2 3 Pin No. Assignment Mating Housing Terminal 1 PF(Power good / Fail signal) GND 2 RS3 JST XHP JST SXH-001T-P0.6 RS+ or equivalent or equivalent 4 RC5 RC+ 6 DC Output Terminal Pin No. Assignment Pin No. 1,2 3,4,5 6 7 Assignment +V1 COM(V1 and V2) +V2 +V3 Pin No. 8 9 10 Assignment -V3 +V4 -V4 Block Diagram fosc : 100KHz POWER SWITCHING PWM CONTROL ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & P.F.C. FAN POWER SWITCHING RECTIFIERS & FILTER REGULATOR MA & CONTROL RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER +V4 -V4 +V3 -V3 +S +V1 COM -S +V2 PF FG O.L.P. O.T.P. PF PWM CONTROL Derating Curve O.V.P. DETECTION CIRCUIT +RC -RC Output Derating VS Input Voltage 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -10 -10 0 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 85 95 105 115 125 135 180 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-375-24-SPEC 2007-04-11 QP-375P 375W Quad Output with PFC Function Mechanical Specification series Unit:mm 250 158 240 5 5 35 LED 1 1 2 6 CN62 3 +V1 ADJ. 113 123 4 5 TB1 TB2 6 +V2 ADJ. 7 1 8 +V3 ADJ. +V4 ADJ. 2 FS1 T6.3A/250V 3 10 3.2 52 6- 9 CN62 Pin No. Assignment : JST S6B-XH or equivalent AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Assignment Terminal Pin No. Mating Housing PF(Power good / Fail signal) 1 GND 2 RS3 JST XHP JST SXH-001T-P0.6 RS+ or equivalent or equivalent 4 RC5 RC+ 6 DC Output Terminal Pin No. Assignment Assignment AC/L AC/N FG Pin No. 1,2 3,4,5 6 7 Assignment +V1 COM(V1 and V2) +V2 +V3 Pin No. 8 9 10 Assignment -V3 +V4 -V4 Derating Curve Output Derating VS Input Voltage 100 100 80CFM 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 85 95 105 115 125 135 180 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-375P-SPEC 2007-04-11 QP-375 375W Quad Output with PFC Function series Control terminal instruction manual +V1 +V1 COM + Load - PF +5V GND COM COM DC 0~15V COM + Load - +V2 COM COM COM COM PF GND RSRS+ RCRC+ PF GND RSRS+ RCRC+ +V1 +V1 COM PF GND RSRS+ RCRC+ + Load - +V1 +V1 +V2 +V2 +V3 +V3 +V3 -V3 -V3 -V3 +V4 +V4 +V4 -V4 -V4 -V4 Remote Sensing COM -V3 Power Fail Signal Power Fail Signal PF Signal is the voltage difference between "GND" and "PF" pin output Power ON: When V RC+ , RC- =0 ~ 0.8V or Open Power OFF: When V RC+ , RC- =4 ~ 10V +V1 +V1 +V1 +V1 COM COM COM COM COM +V2 +V2 +V3 +V3 -V3 -V3 +V4 +V4 -V4 -V4 V3,V4 All Negative(-) -V3+(-V4) +V3 +V4 V3,V4 All Positive(+) -V4 V3 Puls Negative(-) +V1 +V1 +V1 +V1 COM COM COM COM COM COM COM COM COM COM +V2 +V2 +V3 +V3+V4 +V3 -V3 -V3 +V4 +V4 -V4 -V4 V3 Plus V4 Positive(+) File Name:QP-375-SPEC 2007-04-11